TC1001-04 83 © 2004 Cooper Cameron, Cameron Division
T BOP
The Cameron T blowout preventer offers a unique combination of benefits including safety, economy, reli-
ability, extended service life, reduced height and fast and easy service.
Side ram removal on the T BOP permits reduced stack height and facilitates change-out of rams and pack-
ers. Sliding the rams to the side simplifies access and handling and reduces vertical clearance requirements.
The T BOP is available in a modular design which greatly reduces stack height. The design is possible be-
cause the side ram removal feature of the T BOP allows for construction of a BOP stack with virtually no ex-
tra space between BOP body cavities. Each BOP body or module has only a slightly raised face and gasket
prep.
The design of the T is based on Cameron’s experience with the highly successful U and U II ram-type BOPs
and combines much of this proven technology including:
• Metal-to-metal bonnet gaskets increase the safety and reliability in critical service
applications.
• Hydraulic stud tensioning ensures that stud loading is consistently accurate and even.
• Hydraulically operated locking mechanisms, ST Locks, act directly on the operating piston
tailrod and are interlocked by sequence caps to ensure that the locks are unlocked/opened
before the BOP is opened.
• Bonnet studs instead of bonnet bolts reduce the need to make and break threads in the BOP
body.
• Most operating system seals can be replaced with the bonnet in the ram change position
without removing the bonnets.
• The standard T BOP has a large enough piston area to shear all commonly used sizes and
grades of drill pipe.
Other features include hydraulically opening bonnets, forged body and a wide selection of rams to meet all
applications. See pages 114-120 for rams available to fit the T BOP.
TC1001-04 84 © 2004 Cooper Cameron, Cameron Division
T BOP Accessories
A high-pressure, hydraulic pump system is utilized with all Cameron T BOPs fortensioning of the bonnet studs.
Part Number Description
645035-02 High Pressure, Hydraulic Pump Unit to Operate Hydraulic Bonnet Studs
615309-01 10-Foot High-Pressure Hose Assembly for Hydraulic Pump Unit
615309-02 25-Foot High-Pressure Hose Assembly for Hydraulic Pump Unit
708490-01 Male Half of Quick-Disconnect Coupling (One Required per Ram Cavity)
T BOP Hydraulic Control System
The T blowout preventer is designed so that hydraulic pressure opens and closes therams and provides a means for side ram removal.
Ram opening pressure opens the rams and closes the bonnets after ram change-out. Therams are pulled outward, close to the bonnets, before the bonnets begin moving to-wards the preventer body. This assures that the rams never obstruct the bore or inter-fere with pipe in the hole. Hydraulic pressure draws the bonnets tightly against thepreventer body and the bonnet studs are hydraulically tensioned to hold the bonnetsclosed. Ram opening pressure is also used to automatically unlock the ST-locks.
Ram closing pressure closes the rams. When the bonnet nuts are released, closing pres-sure opens the bonnets. When the bonnet has moved to the fully extended position, aram removal tray is inserted and ram opening pressure brings the rams into the clear forremoval. ST-locks are locked by applying pressure to the ST-lock lock port. This pressurewedges a piston-like assembly into position to ensure that the rams are locked in theclosed position. An option is available where the locks are also locked automatically byinstalling a sequence valve in the system.
T BOP Operating Data and Fluid Requirements
Bore Size andWorking Pressure
Gallonsto Open
Pipe Rams(1 set)
Gallonsto Close
Pipe Rams(1 set)
Gallonsto OpenBonnets(1 set)
Gallonsto CloseBonnets(1 set)
ClosingRatio
OpeningRatio
Gallonsto UnlockST Locks
(1 set)
Gallonsto Lock
ST Locks(1 set)
13-5/8” 10,000 psi 12.9 13.9 15.43 13.75 8.6:1 4.3:1 --- ---
18-3/4” 15,000 psi 22.4 24.3 27.63 24.64 6.7:1 3.1:1 3.42 3.41
TC1001-04 85 © 2004 Cooper Cameron, Cameron Division
T BOP Dimensions
Both the 13-5/8” 10,000 psi WP and the 18-3/4” 15,000 psi WP TBOPs are available in sin-gle, double and modular configurations. In addition, end preparations can be API flange,clamp hub or studded connections.
The following designations refer to the T BOP dimensional drawings on the next page:
A-1 Length - bonnets closed, with ST-locks
A-2 Length - bonnets opened, with ST-locks
A-3 Length - bonnets closed, locking screws locked
A-4 Length - bonnets opened, locking screws unlocked
B-1 Height - flanged
B-2 Height - clamp hubs
B-3 Height - studded x flanged
B-4 Height - modular
C Width - no side outlets
D Centerline of preventer to outlet flange or hub face. This distance is variable and must be
determined per individual specifications.
E-1 Top of preventer to centerline of outlet - flanged
E-2 Top of preventer to centerline of outlet - Cameron clamp hubs
E-3 Top of preventer to centerline of outlet - studded x flanged
E-4 Top of preventer to centerline of outlet - modular
F-1 Top of upper ram to top flange face
F-2 Top of upper ram to top hub face
F-3 Top of upper ram to studded face
F-4 Top of upper ram to modular face
G Height of ram
H Centerline of upper outlet to centerline of lower outlet
J Centerline of upper ST-lock (or locking screw) to centerline of lower ST-lock (or locking
screw)
13-5/8” 10,000 psi WP T BOP Dimensions
Style A-3 A-4 B-1 B-2 B-3 B-4 C E-1 E-2 E-3 E-4 F-1 F-2 F-3 F-4 G H J Weight
Single 124” 175.6” 43.6” 34.4” 33.5” 23.3” 32” 26.7” 22.1” 16.6” 16.6” 18” 13.4” 7.9” 7.9” 7.5” 24.6”* 24.6”15,500
lb
Double 124” 175.6” 68.2”* 59.0”* 58.1”* -- 32” 26.7” 22.1” 16.6” -- 18” 13.4” 7.9” -- 7.5” 24.6”* 24.6”27,650
lb
18-3/4” 15,000 psi WP T BOP Dimensions
Style A-1 A-2 B-1 B-2 B-3 B-4 C E-1 E-2 E-3 E-4 F-1 F-2 F-3 F-4 G H J Weight
Single 177” 217” 64.2” 53” 49” 32.1” 47” 40.6” 35.1” 25.6” 24.6” 26.4” 20.8” 11.3” 10.3” 11.5” 34”* 34”44,000
lb
Double 177” 217” 98.3”* 87”* 83.1”* -- 47” 40.6” 35.1” 25.6” -- 26.4” 20.8” 11.3” 10.3” 11.5” 34”* 34”85,000
lb
TC1001-04 86 © 2004 Cooper Cameron, Cameron Division
T BOP Dimensions
SD 034608
A-3 (Bonnets Closed)A-4 (Bonnets Opened)
A-1 (Bonnets Closed)A-2 (Bonnets Opened)
B
B
C
C
D
D
J
J
E
E
F
F
G
G
H
H
13-5/8” 10,000 psi WP T BOP Part Numbers
13-5/8” 10,000 psi WP T BOP Component List and Part Numbers
Item Description Qty Part Number
1 Body (Typical) 1
2* Plug 4 201026
3 TX Bonnet Gasket 2 644799-01
4 Screw, 12 Pt Cap 24 702585-14-00-10
5 Bonnet Stud 8 644652-01
6 Bearing Retainer 4 644653-01
7 Split Bearing 8 644654-01
8 Wear Ring 8 614742-10
9 Bonnet Subassembly, Right Hand 1 644797-01
10 Bonnet Subassembly, Left Hand 1 644797-02
11 Nut Subassembly 8 644616-02
12 Collar Subassembly 8 644789-01
13 O-Ring 4 702645-32-31
14* Pipe Plug 4 K201024
15* Pipe Plug 4 675029-49
16 Ram Guide Pin 4 644658-01
TC1001-04 87 © 2004 Cooper Cameron, Cameron Division
If you require parts certified to API 16A, Please verify part numbers with your local Cameron representative.
TC1001-04 88 © 2004 Cooper Cameron, Cameron Division
13-5/8” 10,000 psi WP T BOP Bonnet Subassembly Part Numbers
13-5/8” 10,000 psi WP T BOP Bonnet Subassembly Parts List
Item Description Qty Part Number Item Description Qty Part Number
30 Bonnet 1 644630-01 59 Retaining Ring, Spirolox 1 018572-18
31 Liner, Operating Cylinder 1 644631-01 60 O-Ring, Size 360 1 702645-36-01
32 O-Ring 1 644768-02 61 Screw, 12 Pt Cap 2 702585-06-00-30
33 Operating Piston Subassembly 1 644791-01 62 Backup Ring 1 644771-01
34 Seal Ring 1 710410 63 Seal Ring 1 710369
35 Wear Ring 1 614742-08 64 Retainer Ring 1 644737-01
36 Ram Change Piston, Open 1 644637-01 65 Retaining Ring, Spirolox 1 708393
37 Ram Change Piston, Closed 1 644637-02 66 Locking Screw Housing 1 644734-01
38 Seal Ring 2 710505 67 Locking Screw 1 644733-01
39 Wear Ring 2 614742-09 68 O-Ring, Size 459 1 702645-45-91
40 Cylinder, Ram Change System 2 644640-01 69 Stud, Double Ended 4 644450-03
41 O-Ring, Size 336 2 702645-33-61 70 Nut 4 644792-01
42 Gland, Ram Change System 2 644641-01 71 Button 1 644635-01
43 Backup Ring 2 644381-06 72 Inner Seal, Hydraulic Bonnet Stud Piston 4 644651-01
44 Seal Ring 2 710504 73 Inner Seal, Hydraulic Bonnet Nut 4 644438-02
45 O-Ring, Size 341 2 702645-34-11 74 Outer Seal, Hydraulic Bonnet Nut 4 644439-02
46 Seal Retainer, Ram Change System 2 644642-01 75 Spacer Ring, Hydraulic Bonnet Stud 4 644650-01
47 Cylinder Head, Ram Change System 2 644643-01 76 O-Ring, Size 362 4 702645-36-22
48 O-Ring, Size 338 2 702645-33-81 77 Retaining Ring, Spirolox 4 033186-05
49 Insert, Bonnet Gasket 1 644644-01 78 Gland 2 017454-46
50 Screw, 12 Pt Cap 12 702585-14-00-26 79 Blind Plug 2 017454-36
51 Backup Ring 2 644381-05 80* Check Valve 1 709493
52 Seal Ring 1 710430 81* Bleeder Plug Assembly 1 640202-02
53 Seal Carrier 1 644726-01 82* High Pressure Plug 4 615684-02
54 O-Ring, Size 352 1 702645-35-21 83* O-Ring, Size 113 4 702645-11-31
55 Seal Ring 1 609745-14 84 Tubing Connector 1 707276
56 Backup Ring 1 644381-04 85 Male Quick-Disconnect 1 708490-01
57 Seal Ring 1 710429
58 Retainer Ring 1 644648-01 *Not Shown
If you require parts certified to API 16A, Please verify part numbers with your local Cameron representative.
TC1001-04 89 © 2004 Cooper Cameron, Cameron Division
18-3/4” 15,000 psi WP T BOP Part Numbers
18-3/4” 15,000 psi WP T BOP Part Numbers
Item Description Qty Part Number
1 Body (Typical) 1
2 Plug 8 201026
3 TX Bonnet Gasket Kit 4 644770-02
4 Screw, 12 Pt Cap 48 702585-14-00-10
5 Bonnet Stud 16 644362-03
6 Bearing Retainer 8 644361-01
7 Split Bearing 16 644360-01
8 Wear Ring 16 645363-01
9 Bonnet Subassembly, Right Hand 2 644562-05
10 Bonnet Subassembly, Left Hand 2 644562-06
11 Nut Subassembly 16 644616-04
12 Collar 16 615707-03
13 O-Ring 8 702645-32-61
16 Ram Guide Pin 8 644399-01
17 Retaining Ring, Spirolox 16 711202
If you require parts certified to API 16A, Please verify part numbers with your local Cameron representative.
TC1001-04 90 © 2004 Cooper Cameron, Cameron Division
18-3/4” 15,000 psi WP T BOP Bonnet SubassemblyPart Numbers
Item Description Qty Part Number Item Description Qty Part Number
30 Bonnet 1 644414-03 56 Spacer Ring, Connecting Rod 1 644355-01
31 Liner, Operating Cylinder 1 644470-01 57 Ret. Ring, Primary Conn. Rod Seal 1 644356-01
32 O-Ring, Size 387 1 702645-38-71 58 Retaining Ring, Spirolox 1 709503
33 Operating Piston Subassembly 1 644483-04 59 O-Ring, Size 453 1 702645-45-31
34 Seal Ring 2 709635 60 Seal Sub, Blind 2 644491-02
35 Wear Ring 1 614742-06 61 O-Ring, Size 214 4 702645-21-41
36 Ram Change Piston, Open 1 644301-01 62 Screw 12 Pt Cap 2 702585-06-00-42
37 Ram Change Piston, Close 1 644301-02 63 Stud, Double Ended 4 644450-01
38 Seal Ring 2 709632 64 Cap Nut 4 644447-01
39 Wear Ring 2 614742-05 65 ST-Lock Assembly 2 645021-01
40 Cylinder, Ram Change System 2 615685-01 69 Gland, Tubing 2 017454-46
41 O-Ring, Size 348 2 702645-34-81 70 Blind Plug 2 017454-36
42 Gland, Ram Change System 2 615711-01 71* Valve, Check 1 709493
43 Backup Ring 2 644381-03 73 High Pressure Plug 4 615684-02
44 Seal Ring 2 709633 74 O-Ring, Size 113 4 702645-11-31
45 O-Ring, Size 428 2 702645-42-81 75 Connector, Tubing 1 707276
46 Seal Retainer, Ram Change System 2 615712-01 76 Male Quick-Disconnect 1 708490-01
47 Cylinder Head, Ram Change System 2 615713-01 77 Button 1 615706-01
48 O-Ring, Size 425 2 702645-42-51 78 Inner Seal, Hydraulic Bonnet Nut 4 644438-01
49 Insert, Bonnet Gasket 1 644358-03-00-01 79 Spacer Ring, Hydraulic Bonnet Stud 4 644359-01
50 Screw, 12 Pt Cap 12 702585-14-00-20 80 Outer Seal, Hydraulic Bonnet Nut 4 644439-01
51 Backup Ring 3 644381-02 81 Piston, Hydraulic Bonnet Stud 4 615709-01
52 Seal Ring 2 709631 82 O-Ring, Size 377 4 702645-37-71
53 Wear Ring 1 644443-01 83 Retaining Ring, Spirolox 4 709636
54 Backup Ring 1 644381-01
55 Seal Ring 1 709630 *Not Shown
High Temperature Connecting Rod Seal Part Numbers*
Item Description Part Number
52 Connecting Rod Seal 712021
55 Connecting Rod Seal 712022
*Order both part numbers.
If you require parts certified to API 16A, Please verify part numbers with your local Cameron representative.
Top Related