BS 2994:1976
This British Standard, having been prepared under the direction of the Iron and Steel Standards Committee, was published under the authority of the Executive Board on 29 October 1976
© BSI 07-1999
First published July 1958First revision October 1976
The following BSI references relate to the work on this standard:Committee reference ISE/59Draft for comment 75/40054DC
ISBN 0 580 09377 8
Cooperating organizations
The Iron and Steel Standards Committee, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations:
British Cast Iron Research Association
British Constructional Steelwork Association*
British Ironfounders’ Association
British Mechanical Engineering Confederation
British Steel Industry*
British Steel Industry — Wire Section
The Concrete Society
Council of Iron Foundry Associations
Department of Industry (National Physical Laboratory)
Electricity Supply Industry in England and Wales
Engineering Equipment Users’ Association
Federation of Civil Engineering Contractors
Greater London Council*
Health and Safety Executive*
Institute of British Foundrymen
Institute of Marine Engineers
Institution of Mechanical Engineers (Automobile Division)
Institution of Production Engineers
Institution of Structural Engineers*
Lloyd’s Register of Shipping
Ministry of Defence
National Association of Drop Forgers and Stampers
Oil Companies Materials Association
Process Plant Association
Royal Institute of British Architects
Shipbuilders’ and Repairers’ National Association
Society of Motor Manufacturers and Traders Ltd.
Steel Castings Research and Trade Association
Tin Research Institute
The Government department and scientific and industrial organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this standard:
Cold Rolled Sections Association
Department of the Environment
Institution of Civil Engineers
Amendments issued since publication
Amd. No. Date of issue Comments
BS 2994:1976
© BSI 07-1999 i
Contents
PageCooperating organizations Inside front coverForeword ii1 Scope 12 Reference 13 Basis of calculation 14 Dimensions and tolerances 1Appendix A Basis of calculation for reduction factors 32Table 1 — Equal angles 2Table 2 — Unequal angles 4Table 3 — Plain channels 6Table 4 — Plain channels 8Table 5 — Inwardly lipped channels 11Table 6 — Inwardly lipped channels 13Table 7 — Outwardly lipped channels 16Table 8 — Outwardly lipped channels 17Table 9 — Tee sections 18Table 10 — Zed sections 22Table 11 — Lipped zed sections 24Table 12 — Plain channels back to back 26Table 13 — Inwardly lipped channels back to back 28Table 14 — Inwardly lipped channels lip to lip 30Publication referred to Inside back cover
BS 2994:1976
ii © BSI 07-1999
Foreword
This British Standard, which was first published in 1958, covers a basic range of sections formed by cold rolling from steel strip. The sizes in this revision include equivalents of previously used imperial sizes and also metric sizes adopted by the European Study Group for Cold Rolled Sections (comprised of members from Austria, Belgium, France, Germany, Italy, Netherlands and the United Kingdom).Although sections may not always be available ex-stock the sizes given in this standard are those most commonly in production. The purchaser would find it advantageous to use these sizes where possible, but size variations can readily be accommodated and in such cases requirements should be discussed with the manufacturer of the section.Attention is drawn to Addendum no. 1(1975) to BS 449-2 for design and construction details.A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity from legal obligations.
Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 32, an inside back cover and a back cover.This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.
BS 2994:1976
© BSI 07-1999 1
1 ScopeThis British Standard specifies the dimensions, mass and geometrical properties of the basic ranges of eight simple and three compound types of cold rolled steel section.
2 ReferenceThe title of the standards publication referred to in this standard is given on the inside back cover.
3 Basis of calculationWhen steel strip is cold roll formed slight thinning occurs at the corners. The actual strip width necessary to form a section is therefore smaller than its theoretical width measured along the centre line of its cross section. For strip widths to be used in practice, experience has evolved reduction factors from which the thinning effect at the corners can be determined. In view of this the properties of the sections given in the tables have been computed using the reduction factors as briefly outlined in Appendix A.
4 Dimensions and tolerances4.1 Dimensions. The dimensions and profiles of the sections shall be in accordance with Table 1 toTable 14.The profile dimensions and angular accuracy shall be measured at a point not less than 150 mm from the end of the section.4.2 Tolerances for simple sections (Table 1 to Table 11). The straightness of any length shall be such that the offset does not exceed 1/600 of that length. The deviation of the profile dimensions shall not exceed ± 0.4 mm. The deviation from the angle of 90° shall not exceed ± 1°. The sections shall be reasonably free from twist and in particular cases the acceptable degree of twist shall be the subject of agreement between the purchaser and the manufacturer.The proportions of the sections may be such that the stated tolerance on the angle could lead to a variation on the overall profile dimensions exceeding the specified tolerance of ± 0.4 mm. In such cases the acceptable tolerance on the angle shall be the subject of agreement between the purchaser and the manufacturer.
The ± 0.4 mm profile tolerance shall not apply to elements having a free edge, e.g. lengths of the legs of angles, channels, tees and zed sections and the lips of lipped channels and lipped zed sections, etc. In these cases the tolerances shall be as follows.
The foregoing tolerances apply to all sections within the ranges included in Table 1 to Table 11 (i.e. sections of the same shape but of intermediate sizes and thicknesses); tolerances on cold rolled sections outside the basic ranges tabulated should be the subject of agreement between the purchaser and the manufacturer.The tolerances on ordered lengths shall be as follows.
For manufacturing reasons the corner radii may vary slightly from those shown in the tables. This, however, has a negligible effect on the properties of the section.4.3 Tolerances for compound sections(Table 12, Table 13 and Table 14). For compound sections, the tolerances shall be the subject of agreement between the purchaser and the manufacturer.
Thickness Permissible deviation
mm mm
less than 3.03.0 up to but not including 5.05.0 and over
± 0.75
± 1.25± 1.50
Ordered length Permissible deviation
m mm
up to and including 3over 3, up to and including 6over 6
± 0.8
± 1.5± 3.0
BS
2994:1976
2©
BS
I 07-1999
Table 1 — Equal angles
Designation Dimensions Mass/unit lengths
Area of section
Centre of gravity
Moment of inertia Radius of gyration Elastic modulus
Product moment of
inertia
A × A × t A t r Cx Cy About X–X, Y–Y
AboutU–U
About V–V
About X–X, Y–Y
About U–U
About V–V
About X–X, Y–Y
About XY
mm mm mm mm kg/m cm2 cm cm cm4 cm4 cm4 cm cm cm cm3 cm4
20 × 20 × 1.2 1.2 1.2 0.355 0.452 0.560 0.560 0.179 0.292 0.0667 0.630 0.804 0.384 0.125 0.133
20 × 20 × 1.6 20 1.6 1.6 0.463 0.590 0.580 0.580 0.231 0.378 0.0834 0.625 0.800 0.376 0.162 0.147
20 × 20 × 2 2 2 0.567 0.722 0.600 0.600 0.278 0.458 0.0977 0.620 0.797 0.368 0.198 0.180
25 × 25 × 1.6 1.6 1.6 0.589 0.750 0.705 0.705 0.464 0.756 0.171 0.787 1.00 0.478 0.258 0.293
25 × 25 × 2 25 2 2 0.724 0.922 0.725 0.725 0.563 0.923 0.204 0.782 1.00 0.470 0.317 0.359
25 × 25 × 3 3 3 1.04 1.32 0.776 0.776 0.784 1.30 0.258 0.769 0.991 0.450 0.455 0.516
30 × 30 × 1.6 1.6 1.6 0.714 0.910 0.830 0.830 0.817 1.33 0.306 0.948 1.21 0.580 0.377 0.511
30 × 30 × 2 30 2 2 0.881 1.12 0.850 0.850 0.997 1.63 0.367 0.943 1.20 0.572 0.464 0.630
30 × 30 × 3 3 3 1.27 1.62 0.900 0.900 1.41 2.32 0.495 0.931 1.19 0.552 0.670 0.912
40 × 40 × 1.6
40
1.6 1.6 0.965 1.23 1.08 1.08 1.99 3.21 0.757 1.27 1.62 0.784 0.680 1.23
40 × 40 × 2 2 2 1.19 1.52 1.10 1.10 2.44 3.96 0.917 1.27 1.61 0.776 0.840 1.52
40 × 40 × 2.5 2.5 2.5 1.47 1.88 1.12 1.12 2.98 4.85 1.10 1.26 1.61 0.766 1.04 1.88
40 × 40 × 3 3 3 1.75 2.22 1.15 1.15 3.49 5.71 1.27 1.25 1.60 0.756 1.23 2.22
50 × 50 × 2 2 2 1.51 1.92 1.35 1.35 4.85 7.85 1.85 1.59 2.02 0.980 1.33 3.00
50 × 50 × 2.5 50 2.5 2.5 1.87 2.38 1.37 1.37 5.95 9.66 2.24 1.58 2.02 0.970 1.64 3.71
50 × 50 × 3 3 3 2.22 2.82 1.40 1.40 7.01 11.4 2.60 1.58 2.01 0.960 1.95 4.41
BS
2994:1976
© B
SI 07-1999
3
Table 1 — Equal angles
Designation Dimensions Mass/unit lengths
Area of section
Centre of gravity
Moment of inertia Radius of gyration Elastic modulus
Product moment of
inertia
A × A × t A t r Cx Cy About X–X, Y–Y
AboutU–U
About V–V
About X–X, Y–Y
About U–U
About V–V
About X–X, Y–Y
About XY
mm mm mm mm kg/m cm2 cm cm cm4 cm4 cm4 cm cm cm cm3 cm4
60 × 60 × 2
60
2 2 1.82 2.32 1.60 1.60 8.48 13.7 3.26 1.91 2.43 1.18 1.93 5.22
60 × 60 × 2.5 2.5 2.5 2.26 2.88 1.62 1.62 10.4 16.9 3.97 1.90 2.42 1.17 2.39 6.47
60 × 60 × 3 3 3 2.69 3.42 1.65 1.65 12.3 20.0 4.64 1.90 2.42 1.16 2.84 7.69
60 × 60 × 4 4 4 3.52 4.49 1.70 1.70 16.0 26.0 5.87 1.89 2.41 1.14 3.71 10.1
70 × 70 × 3
70
3 3 3.16 4.02 1.90 1.90 19.8 32.2 7.54 2.22 2.83 1.37 3.89 12.3
70 × 70 × 4 4 4 4.15 5.29 1.95 1.95 25.8 42.0 9.61 2.21 2.82 1.35 5.10 16.2
70 × 70 × 5 5 7.5 5.08 6.48 2.01 2.01 31.2 51.3 11.2 2.20 2.81 1.31 6.26 20.0
80 × 80 × 3
80
3 3 3.63 4.62 2.15 2.15 29.9 48.4 11.4 2.54 3.23 1.57 5.11 18.5
80 × 80 × 4 4 4 4.78 6.09 2.20 2.20 39.0 63.3 14.7 2.53 3.22 1.55 6.72 24.3
80 × 80 × 5 5 7.5 5.87 7.48 2.26 2.26 47.4 77.6 17.3 2.52 3.22 1.52 8.27 30.2
80 × 80 × 6 6 9 6.94 8.85 2.31 2.31 55.6 91.4 19.8 2.51 3.21 1.50 9.77 35.8
100 × 100 × 3
100
3 3 4.57 5.82 2.65 2.65 59.2 95.6 22.9 3.19 4.05 1.98 8.06 36.4
100 × 100 × 4 4 4 6.03 7.69 2.70 2.70 77.5 126 29.6 3.18 4.04 1.96 10.6 48.0
100 × 100 × 5 5 7.5 7.44 9.48 2.76 2.76 94.9 155 35.3 3.16 4.04 1.93 13.1 59.6
100 × 100 × 6 6 9 8.83 11.2 2.81 2.81 112 183 40.8 3.15 4.03 1.91 15.5 70.9
BS
2994:1976
4©
BS
I 07-1999
Table 2 — Unequal angles
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia Radius of gyration Angle
!
Elastic modulus Product moment
of inertia
A × B × t A B t r Cx Cy About X–X
AboutY–Y
About U–U
About V–V
About X–X
AboutY–Y
About U–U
About V–V
About X–X
AboutY–Y
AboutXY
mm mm mm mm mm kg/m cm2 cm cm cm4 cm4 cm4 cm4 cm cm cm cm tan ! cm3 cm3 cm4
20 × 15 × 1.2 1.2 1.2 0.308 0.392 0.636 0.378 0.162 0.0802 0.204 0.0386 0.643 0.452 0.721 0.314 0.580 0.119 0.0714 0.0716
20 × 15 × 1.6 20 15 1.6 1.6 0.400 0.510 0.658 0.396 0.207 0.102 0.262 0.0479 0.638 0.448 0.716 0.306 0.584 0.155 0.0927 0.0931
20 × 15 × 2 2 2 0.488 0.622 0.681 0.415 0.248 0.122 0.315 0.0556 0.632 0.443 0.712 0.299 0.588 0.188 0.113 0.113
30 × 15 × 1.2 1.2 1.2 0.402 0.512 1.07 0.303 0.491 0.0896 0.527 0.0533 0.980 0.418 1.02 0.323 0.288 0.255 0.0749 0.126
30 × 15 × 1.6 30 15 1.6 1.6 0.526 0.670 1.10 0.321 0.634 0.115 0.681 0.0673 0.973 0.414 1.01 0.317 0.290 0.333 0.0973 0.164
30 × 15 × 2 2 2 0.645 0.822 1.12 0.338 0.766 0.138 0.824 0.0796 0.966 0.410 1.00 0.311 0.292 0.408 0.119 0.200
30 × 20 × 1.6 30 20 1.6 1.6 0.589 0.750 0.990 0.473 0.708 0.262 0.834 0.137 0.972 0.592 1.05 0.427 0.469 0.352 0.172 0.268
30 × 20 × 2 2 2 0.724 0.922 1.01 0.492 0.860 0.318 1.01 0.162 0.966 0.587 1.05 0.420 0.472 0.433 0.211 0.329
40 × 20 × 1.6 1.6 1.6 0.714 0.910 1.43 0.404 1.55 0.283 1.67 0.169 1.31 0.558 1.35 0.430 0.288 0.604 0.177 0.398
40 × 20 × 2 40 20 2 2 0.881 1.12 1.46 0.422 1.89 0.343 2.03 0.202 1.30 0.553 1.35 0.424 0.289 0.744 0.218 0.489
40 × 20 × 2.5 2.5 2.5 1.08 1.38 1.49 0.444 2.29 0.414 2.47 0.240 1.29 0.548 1.34 0.417 0.291 0.913 0.266 0.598
40 × 25 × 2 40 25 2 2 0.959 1.22 1.34 0.571 2.06 0.652 2.36 0.352 1.30 0.731 1.39 0.537 0.419 0.777 0.338 0.717
40 × 25 × 2.5 2.5 2.5 1.18 1.50 1.37 0.594 2.51 0.790 2.88 0.420 1.29 0.725 1.38 0.528 0.421 0.955 0.415 0.880
50 × 25 × 1.6 1.6 1.6 0.903 1.15 1.76 0.487 3.09 0.567 3.32 0.340 1.64 0.702 1.70 0.544 0.287 0.955 0.282 0.789
50 × 25 × 2 50 25 2 2 1.12 1.42 1.79 0.505 3.79 0.691 4.07 0.412 1.63 0.697 1.69 0.538 0.288 1.18 0.347 0.972
50 × 25 × 2.5 2.5 2.5 1.38 1.75 1.82 0.527 4.62 0.839 4.97 0.493 1.62 0.692 1.68 0.531 0.289 1.45 0.425 1.19
BS
2994:1976
© B
SI 07-1999
5
Table 2 — Unequal angles
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia Radius of gyration Angle
!
Elastic modulus
Product moment
of inertia
A × B × t A B t r Cx Cy About X–X
AboutY–Y
About U–U
About V–V
About X–X
AboutY–Y
About U–U
About V–V
About X–X
AboutY–Y
AboutXY
mm mm mm mm mm kg/m cm2 cm cm cm4 cm4 cm4 cm4 cm cm cm cm tan ! cm3 cm3 cm4
60 × 30 × 260 30
2 2 1.35 1.72 2.12 0.588 6.66 1.22 7.14 0.731 1.97 0.841 2.04 0.652 0.287 1.72 0.505 1.7060 × 30 × 3 3 3 1.98 2.52 2.18 0.633 9.59 1.74 10.3 1.02 1.95 0.830 2.02 0.637 0.289 2.51 0.735 2.48
80 × 30 × 2.5 2 2 1.67 2.12 3.04 0.496 14.5 1.30 15.0 0.850 2.62 0.782 2.66 0.633 0.181 2.93 0.518 2.4780 × 30 × 2.5 80 30 2.5 2.5 2.06 2.63 3.08 0.518 17.8 1.58 18.4 1.03 2.61 0.776 2.65 0.626 0.181 3.62 0.638 3.0580 × 30 × 3 3 3 2.45 3.12 3.11 0.540 21.0 1.86 21.7 1.20 2.59 0.771 2.63 0.620 0.182 4.30 0.755 3.60
80 × 50 × 3 3 3 2.92 3.72 2.63 1.10 25.4 8.08 29.1 4.43 2.61 1.47 2.79 1.09 0.417 4.74 2.07 8.7680 × 50 × 4 80 50 4 4 3.84 4.89 2.69 1.14 33.0 10.4 37.8 5.64 2.60 1.46 2.78 1.07 0.419 6.21 2.71 11.580 × 50 × 5 5 7.5 4.69 5.98 2.76 1.20 39.8 12.6 45.9 6.54 2.58 1.45 2.77 1.05 0.426 7.61 3.31 14.2
100 × 30 × 3 3 3 2.92 3.72 4.06 0.477 38.7 1.94 39.3 1.33 3.22 0.721 3.25 0.598 0.127 6.51 0.768 4.76100 × 30 × 4 100 30 4 4 3.84 4.89 4.13 0.521 50.0 2.47 50.8 1.69 3.20 0.711 3.22 0.588 0.127 8.52 0.997 6.15100 × 30 × 5 5 7.5 4.69 5.98 4.23 0.569 59.9 2.95 60.9 1.97 3.17 0.703 3.19 0.574 0.130 10.4 1.22 7.54
100 × 50 × 3
100 50
3 3 3.39 4.32 3.52 0.966 46.6 8.55 50.0 5.15 3.28 1.41 3.40 1.09 0.286 7.19 2.12 11.9100 × 50 × 4 4 4 4.46 5.69 3.58 1.01 60.6 11.1 65.1 6.58 3.27 1.39 3.38 1.08 0.288 9.44 2.77 15.6100 × 50 × 5 5 7.5 5.48 6.98 3.66 1.06 73.5 13.4 79.1 7.74 3.24 1.38 3.37 1.05 0.293 11.6 3.39 19.2100 × 50 × 6 6 9 6.47 8.25 3.73 1.11 85.8 15.6 92.5 8.86 3.23 1.37 3.35 1.04 0.295 13.7 4.00 22.7
BS
2994:1976
6©
BS
I 07-1999
Table 3 — Plain channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus Shear centre
Torsion constant
Warping constant
D × B × t D B t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
20 × 20 × 1.2 1.2 1.2 0.521 0.664 0.741 0.454 0.277 0.827 0.646 0.454 0.220 1.55 0.0031 0.16420 × 20 × 1.6 20 20 1.6 1.6 0.675 0.860 0.766 0.563 0.351 0.809 0.639 0.563 0.284 1.55 0.0071 0.19320 × 20 × 2 2 2 0.819 1.04 0.792 0.653 0.416 0.791 0.631 0.653 0.344 1.55 0.0134 0.211
25 × 25 × 1.2
25 25
1.2 1.2 0.662 0.844 0.907 0.926 0.557 1.05 0.813 0.741 0.350 1.93 0.0040 0.53725 × 25 × 1.6 1.6 1.6 0.863 1.10 0.932 1.17 0.714 1.03 0.806 0.932 0.455 1.93 0.0092 0.65025 × 25 × 2 2 2 1.05 1.34 0.957 1.37 0.857 1.01 0.799 1.10 0.555 1.94 0.0174 0.73525 × 25 × 2.5 2.5 2.5 1.28 1.63 0.990 1.59 1.02 0.989 0.789 1.28 0.672 1.93 0.0326 0.805
30 × 30 × 1.6 1.6 1.6 1.05 1.34 1.10 2.09 1.27 1.25 0.973 1.40 0.666 2.32 0.0112 1.7230 × 30 × 2 30 30 2 2 1.29 1.64 1.12 2.49 1.53 1.23 0.966 1.66 0.816 2.32 0.0214 1.9930 × 30 × 3 3 3 1.84 2.35 1.19 3.31 2.11 1.19 0.947 2.20 1.16 2.32 0.0677 2.40
40 × 40 × 1.6
40 40
1.6 1.6 1.43 1.82 1.43 5.20 3.10 1.69 1.31 2.60 1.21 3.08 0.0153 7.8640 × 40 × 2 2 2 1.76 2.24 1.46 6.27 3.79 1.67 1.30 3.14 1.49 3.09 0.0294 9.2740 × 40 × 2.5 2.5 2.5 2.16 2.76 1.49 7.50 4.59 1.65 1.29 3.75 1.83 3.09 0.0561 10.740 × 40 × 3 3 3 2.55 3.25 1.52 8.60 5.33 1.63 1.28 4.30 2.15 3.10 0.0947 11.9
50 × 50 × 2
50 50
2 2 2.23 2.84 1.79 12.7 7.58 2.11 1.63 5.08 2.36 3.85 0.0374 30.050 × 50 × 2.5 2.5 2.5 2.75 3.51 1.82 15.3 9.24 2.09 1.62 6.13 2.91 3.86 0.0717 35.450 × 50 × 3 3 3 3.26 4.15 1.85 17.7 10.8 2.07 1.62 7.09 3.44 3.87 0.122 40.050 × 50 × 4 4 4 4.22 5.37 1.91 22.0 13.7 2.02 1.60 8.79 4.44 3.87 0.278 47.0
BS
2994:1976
© B
SI 07-1999
7
Table 3 — Plain channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus Shear centre
Torsion constant
Warping constant
D × B × t D B t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
60 × 60 × 2 2 2 2.70 3.44 2.12 22.5 13.3 2.55 1.97 7.49 3.43 4.62 0.0454 77.460 × 60 × 3 60 60 3 3 3.96 5.05 2.18 31.8 19.2 2.51 1.95 10.6 5.02 4.63 0.149 10660 × 60 × 4 4 4 5.16 6.57 2.25 39.9 24.5 2.46 1.93 13.3 6.53 4.64 0.342 127
80 × 80 × 2
80 80
2 2 3.65 4.64 2.79 54.8 32.7 3.44 2.63 13.7 6.18 6.14 0.0614 34280 × 80 × 3 3 3 5.38 6.85 2.85 78.7 46.9 3.39 2.62 19.7 9.10 6.16 0.203 47880 × 80 × 5 5 7.5 8.60 11.0 2.99 119 72.7 3.29 2.58 29.7 14.5 6.20 0.895 66680 × 80 × 6 6 9 10.1 12.9 3.06 136 84.3 3.25 2.56 34.0 17.1 6.20 1.51 732
100 × 100 × 2
100 100
2 2 4.59 5.84 3.45 109 63.6 4.32 3.30 21.8 9.72 7.67 0.0774 1 070100 × 100 × 3 3 3 6.79 8.65 3.52 158 93.2 4.27 3.28 31.6 14.4 7.69 0.257 1 520100 × 100 × 5 5 7.5 11.0 14.0 3.66 243 147 4.18 3.24 48.7 23.2 7.74 1.15 2 210100 × 100 × 6 6 9 12.9 16.5 3.73 281 172 4.13 3.23 56.2 27.4 7.75 1.94 2 480
BS
2994:1976
8©
BS
I 07-1999
Table 4 — Plain channels
Designation Dimensions Mass/unit length
Area ofsection
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus Shear centre
Torsion constant
Warping constant
D × B × t D B t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
30 × 15 × 1.230 15
1.2 1.2 0.521 0.664 0.435 0.899 0.146 1.16 0.469 0.599 0.137 0.941 0.0031 0.19730 × 15 × 1.6 1.6 1.6 0.675 0.860 0.455 1.12 0.185 1.14 0.464 0.749 0.177 0.940 0.0071 0.234
30 × 20 × 1.230 20
1.2 1.2 0.615 0.784 0.636 1.15 0.324 1.21 0.643 0.765 0.238 1.38 0.0037 0.44430 × 20 × 2 2 2 0.976 1.24 0.681 1.71 0.497 1.17 0.632 1.14 0.377 1.39 0.0160 0.606
40 × 15 × 1.240 15
1.2 1.2 0.615 0.784 0.378 1.78 0.160 1.51 0.452 0.891 0.143 0.838 0.0037 0.40340 × 15 × 2 2 2 0.976 1.24 0.415 2.66 0.244 1.46 0.443 1.33 0.225 0.832 0.0160 0.552
40 × 20 × 240 20
2 2 1.13 1.44 0.600 3.38 0.556 1.53 0.620 1.69 0.397 1.25 0.0187 1.2740 × 20 × 3 3 3 1.61 2.05 0.651 4.48 0.758 1.48 0.608 2.24 0.562 1.25 0.0587 1.51
40 × 25 × 1.6 1.6 1.6 1.05 1.34 0.779 3.43 0.858 1.60 0.800 1.72 0.498 1.70 0.0112 2.0840 × 25 × 2 40 25 2 2 1.29 1.64 0.801 4.11 1.04 1.58 0.795 2.05 0.611 1.70 0.0214 2.4140 × 25 × 2.5 2.5 2.5 1.57 2.01 0.828 4.86 1.25 1.56 0.788 2.43 0.745 1.70 0.0405 2.73
50 × 25 × 1.6
50 25
1.6 1.6 1.18 1.50 0.705 5.76 0.928 1.96 0.787 2.30 0.517 1.57 0.0126 3.6050 × 25 × 2 2 2 1.45 1.84 0.725 6.93 1.13 1.94 0.782 2.77 0.634 1.57 0.0240 4.2250 × 25 × 2.5 2.5 2.5 1.77 2.26 0.750 8.26 1.36 1.91 0.776 3.30 0.775 1.57 0.0457 4.8550 × 25 × 3 3 3 2.08 2.65 0.776 9.44 1.57 1.89 0.769 3.78 0.909 1.56 0.0767 5.32
50 × 40 × 1.6
50 40
1.6 1.6 1.55 1.98 1.32 8.57 3.37 2.08 1.31 3.43 1.26 2.91 0.0167 13.450 × 40 × 2 2 2 1.92 2.44 1.34 10.4 4.12 2.06 1.30 4.16 1.55 2.92 0.0320 15.950 × 40 × 2.5 2.5 2.5 2.36 3.01 1.37 12.5 5.01 2.04 1.29 5.00 1.91 2.92 0.0613 18.650 × 40 × 3 3 3 2.78 3.55 1.40 14.4 5.85 2.02 1.28 5.77 2.25 2.92 0.104 20.9
60 × 30 × 1.6
60 30
1.6 1.6 1.43 1.82 0.830 10.2 1.63 2.37 0.948 3.40 0.753 1.88 0.0153 9.3460 × 30 × 2 2 2 1.76 2.24 0.850 12.4 1.99 2.35 0.943 4.12 0.927 1.88 0.0294 11.160 × 30 × 3 3 3 2.55 3.25 0.900 17.1 2.81 2.30 0.931 5.71 1.34 1.88 0.0947 14.560 × 30 × 4 4 4 3.28 4.17 0.951 21.0 3.52 2.25 0.919 7.01 1.72 1.87 0.214 16.6
BS
2994:1976
© B
SI 07-1999
9
Table 4 — Plain channels
Designation Dimensions Mass/unit length
Area ofsection
Centre of gravity
Moment of inertia Radius of gyration
Elastic modulus Shear centre
Torsion constant
Warping constant
D × B × t D B t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
60 × 40 × 2 2 2 2.08 2.64 1.25 15.7 4.41 2.44 1.29 5.24 1.60 2.77 0.0347 24.860 × 40 × 3 60 40 3 3 3.02 3.85 1.31 22.0 6.29 2.39 1.28 7.34 2.33 2.77 0.113 33.060 × 40 × 4 4 4 3.90 4.97 1.36 27.3 7.95 2.34 1.26 9.11 3.01 2.77 2.257 38.8
60 × 50 × 260 50
2 2 2.39 3.04 1.68 19.1 8.11 2.51 1.63 6.37 2.44 3.68 0.0400 46.360 × 50 × 3 3 3 3.49 4.45 1.74 26.9 11.6 2.46 1.62 8.96 3.56 3.69 0.131 62.670 × 30 × 1.6 1.6 1.6 1.55 1.98 0.769 14.6 1.72 2.72 0.932 4.18 0.770 1.77 0.0167 13.670 × 30 × 2 70 30 2 2 1.92 2.44 0.788 17.8 2.10 2.70 0.927 5.08 0.949 1.77 0.0320 16.270 × 30 × 3 3 3 2.78 3.55 0.837 24.8 2.97 2.64 0.915 7.08 1.37 1.77 0.104 21.470 × 40 × 2 2 2 2.23 2.84 1.17 22.4 4.66 2.81 1.28 6.40 1.65 2.63 0.0374 36.070 × 40 × 3 70 40 3 3 3.26 4.15 1.22 31.5 6.66 2.76 1.27 9.01 2.40 2.63 0.122 48.570 × 40 × 4 4 4 4.22 5.37 1.27 39.4 8.45 2.71 1.25 11.3 3.10 2.63 0.278 57.7
80 × 25 × 1.6
80 25
1.6 1.6 1.55 1.98 0.553 17.6 1.07 2.98 0.735 4.39 0.550 1.29 0.0167 11.480 × 25 × 2 2 2 1.92 2.44 0.571 21.3 1.30 2.96 0.731 5.34 0.677 1.29 0.0320 13.580 × 25 × 3 3 3 2.78 3.55 0.617 29.8 1.84 2.90 0.720 7.44 0.976 1.28 0.104 17.880 × 25 × 4 4 4 3.59 4.57 0.662 36.8 2.30 2.84 0.709 9.20 1.25 1.26 0.235 20.7
80 × 40 × 1.6 1.6 1.6 1.93 2.46 1.08 25.0 3.97 3.18 1.27 6.24 1.36 2.51 0.0208 41.480 × 40 × 2 80 40 2 2 2.39 3.04 1.10 30.5 4.87 3.16 1.27 7.62 1.68 2.51 0.0400 49.880 × 40 × 3 3 3 3.49 4.45 1.15 43.1 6.98 3.11 1.25 10.8 2.45 2.51 0.131 67.780 × 40 × 4 4 4 4.53 5.77 1.20 54.1 8.89 3.06 1.24 13.5 3.18 2.51 0.299 81.3
80 × 50 × 2
80 50
2 2 2.70 3.44 1.49 36.6 8.99 3.26 1.62 9.14 2.57 3.38 0.0454 92.480 × 50 × 3 3 3 3.96 5.05 1.55 52.0 13.0 3.21 1.60 13.0 3.76 3.39 0.149 12780 × 50 × 4 4 4 5.16 6.57 1.60 65.7 16.6 3.16 1.59 16.4 4.89 3.39 0.342 15480 × 50 × 5 5 7.5 6.24 7.95 1.67 76.5 19.7 3.10 1.57 19.1 5.92 3.40 0.645 166
80 × 60 × 2 2 2 3.02 3.84 1.91 42.6 14.8 3.33 1.96 10.7 3.61 4.29 0.0507 15380 × 60 × 3 80 60 3 3 4.43 5.65 1.97 60.9 21.4 3.28 1.95 15.2 5.31 4.30 0.167 21280 × 60 × 4 4 4 5.79 7.37 2.02 77.3 27.5 3.24 1.93 19.3 6.92 4.30 0.385 260
90 × 40 × 1.6 1.6 1.6 2.06 2.62 1.02 32.8 4.12 3.54 1.25 7.28 1.38 2.40 0.0221 55.090 × 40 × 2 90 40 2 2 2.55 3.24 1.04 40.1 5.06 3.52 1.25 8.91 1.71 2.40 0.0427 66.390 × 40 × 3 3 3 3.73 4.75 1.09 56.9 7.27 3.46 1.24 12.7 2.49 2.40 0.140 90.7
90 × 50 × 1.6 1.6 1.6 2.31 2.94 1.40 39.0 7.60 3.64 1.61 8.67 2.11 3.25 0.0249 10190 × 50 × 2 90 50 2 2 2.86 3.64 1.42 47.8 9.36 3.62 1.60 10.6 2.61 3.25 0.0480 12390 × 50 × 3 3 3 4.20 5.35 1.47 68.3 13.5 3.57 1.59 15.2 3.83 3.26 0.158 169
100 × 40 × 1.6
100 40
1.6 1.6 2.18 2.78 0.964 41.9 4.25 3.88 1.24 8.38 1.40 2.30 0.0235 70.8100 × 40 × 2 2 2 2.70 3.44 0.983 51.3 5.23 3.86 1.23 10.3 1.73 2.30 0.0454 85.6100 × 40 × 3 3 3 3.96 5.05 1.03 73.1 7.52 3.81 1.22 14.6 2.53 2.30 0.149 118100 × 40 × 4 4 4 5.16 6.57 1.08 92.5 9.60 3.75 1.21 18.5 3.29 2.29 0.342 143
BS
2994:1976
10©
BS
I 07-1999
Table 4 — Plain channels
Designation Dimensions Mass/unit length
Area ofsection
Centre of gravity
Moment of inertia Radius of gyration
Elastic modulus Shear centre
Torsion constant
Warping constant
D × B × t D B t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
100 × 50 × 2
100 50
2 2 3.02 3.84 1.35 60.9 9.69 3.98 1.59 12.2 2.66 3.14 0.0507 158100 × 50 × 3 3 3 4.43 5.65 1.40 87.2 14.0 3.93 1.58 17.4 3.89 3.14 0.167 219100 × 50 × 4 4 4 5.79 7.37 1.45 111 18.0 3.88 1.56 22.2 5.08 3.14 0.385 270100 × 50 × 5 5 7.5 7.03 8.95 1.51 130 21.5 3.82 1.55 26.1 6.17 3.15 0.729 297
100 × 60 × 2
100 60
2 2 3.33 4.24 1.74 70.5 16.0 4.08 1.94 14.1 3.75 4.00 0.0560 261100 × 60 × 3 3 3 4.90 6.25 1.79 101 23.2 4.03 1.93 20.3 5.51 4.01 0.185 365100 × 60 × 4 4 4 6.42 8.17 1.85 129 29.9 3.98 1.91 25.9 7.20 4.02 0.427 452100 × 60 × 5 5 7.5 7.81 9.95 1.91 153 35.9 3.92 1.90 30.6 8.79 4.03 0.812 505
120 × 50 × 3120 50
3 3 4.90 6.25 1.28 134 14.9 4.63 1.54 22.3 4.00 2.92 0.185 343120 × 50 × 4 4 4 6.42 8.17 1.33 171 19.2 4.57 1.53 28.5 5.22 2.92 0.427 425120 × 50 × 5 5 7.5 7.81 9.95 1.39 202 23.0 4.51 1.52 33.7 6.36 2.93 0.812 475
120 × 60 × 4120 60
4 4 7.04 8.97 1.70 198 31.9 4.70 1.89 33.0 7.42 3.77 0.470 709120 × 60 × 5 5 7.5 8.60 11.0 1.76 235 38.4 4.63 1.87 39.2 9.07 3.78 0.895 803120 × 60 × 6 6 9 10.1 12.9 1.82 270 44.6 4.58 1.86 45.1 10.7 3.78 1.51 887
140 × 60 × 4140 60
4 4 7.67 9.77 1.58 284 33.6 5.39 1.85 40.6 7.59 3.55 0.513 1 040140 × 60 × 6 6 9 11.1 14.1 1.69 391 47.2 5.27 1.83 55.9 10.9 3.56 1.66 1 320
150 × 50 × 3150 50
3 3 5.61 7.135 1.14 227 15.9 5.64 1.49 30.3 4.11 2.66 0.212 590150 × 50 × 4 4 4 7.36 9.37 1.18 292 20.5 5.58 1.48 38.9 5.37 2.65 0.491 739150 × 50 × 5 5 7.5 8.99 11.5 1.24 348 24.7 5.51 1.47 46.3 6.56 2.66 0.937 840
180 × 50 × 3180 50
3 3 6.32 8.05 1.03 353 16.7 6.62 1.44 39.2 4.19 2.44 0.239 918180 × 50 × 5 5 7.5 10.2 13.0 1.12 545 26.0 6.48 1.42 60.5 6.71 2.43 1.06 1 330
200 × 50 × 4 4 4 8.93 11.4 1.01 590 22.1 7.20 1.39 59.0 5.54 2.30 0.598 1 490200 × 50 × 5 200 50 5 7.5 11.0 14.0 1.06 708 26.7 7.12 1.38 70.8 6.79 2.30 1.15 1 730200 × 50 × 6 6 9 12.9 16.5 1.11 821 31.1 7.05 1.37 82.1 7.99 2.29 1.94 1 940
200 × 80 × 4 4 4 10.8 13.8 1.97 821 83.6 7.72 2.46 82.1 13.9 4.60 0.726 5 480200 × 80 × 5 200 80 5 7.5 13.3 17.0 2.02 993 102 7.65 2.45 99.3 17.1 4.62 1.40 6 460200 × 80 × 6 6 9 15.8 20.1 2.07 1 160 120 7.60 2.44 116 20.2 4.62 2.38 7 380
250 × 50 × 4 4 4 10.5 13.4 0.889 1 030 23.3 8.78 1.32 82.5 5.66 2.03 0.705 2 560250 × 50 × 5 250 50 5 7.5 12.9 16.5 0.937 1 240 28.2 8.69 1.31 99.4 6.94 2.03 1.35 2 990250 × 50 × 6 6 9 15.3 19.5 0.983 1 450 32.9 8.62 1.30 116 8.18 2.02 2.30 3 380
250 × 80 × 4 4 4 12.4 15.8 1.74 1 390 89.1 9.40 2.38 112 14.2 4.18 0.833 9 390250 × 80 × 5 250 80 5 7.5 15.3 19.5 1.80 1 690 109 9.33 2.37 135 17.6 4.19 1.60 11 160250 × 80 × 6 6 9 18.1 23.1 1.84 1 980 128 9.27 2.35 159 20.8 4.18 2.74 12 830
BS
2994:1976
© B
SI 07-1999
11
Table 5 — Inwardly lipped channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus Shear centre
Torsion constant
Warping constant
D × B × C × t D B C t r CY About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
25 × 25 × 8 × 1.225 25 8
1.2 1.2 0.769 0.979 1.12 0.994 0.831 1.01 0.921 0.795 0.602 2.45 0.0046 1.8325 × 25 × 8 × 1.6 1.6 1.6 0.986 1.26 1.12 1.22 1.01 0.987 0.899 0.979 0.732 2.39 0.0103 2.14
30 × 30 × 10 × 1.230 30 10
1.2 1.2 1.948 1.21 1.36 1.79 1.52 1.22 1.12 1.19 0.927 3.00 0.0057 5.1930 × 30 × 10 × 1.6 1.6 1.6 1.22 1.56 1.35 2.23 1.89 1.20 1.10 1.49 1.15 2.94 0.0129 6.22
35 × 35 × 10 × 1.235 35 10
1.2 1.2 1.09 1.39 1.53 2.90 2.35 1.45 1.30 1.66 1.19 3.39 0.0065 9.2535 × 10 × 10 × 1.6 1.6 1.6 1.41 1.80 1.53 3.66 2.94 1.43 1.28 2.09 1.49 3.34 0.0149 11.2
40 × 40 × 10 × 1.240 40 10
1.2 1.2 1.23 1.57 1.70 4.39 3.42 1.67 1.48 2.19 1.49 3.79 0.0074 15.640 × 40 × 10 × 1.6 1.6 1.6 1.60 2.04 1.70 5.57 4.32 1.65 1.45 2.79 1.88 3.73 0.0170 19.1
40 × 40 × 15 × 2 40 40 15 2 2 2.11 2.69 1.86 6.75 5.99 1.59 1.49 3.38 2.80 4.06 0.0347 41.5
50 × 50 × 10 × 1.6 50 50 10 1.6 1.6 1.98 2.52 2.04 11.2 8.18 2.10 1.80 4.47 2.76 4.50 0.0211 48.7
50 × 50 × 15 × 2 50 50 15 2 2 2.58 3.29 2.21 13.7 11.3 2.04 1.85 5.49 4.04 4.87 0.0427 94.1
60 × 60 × 15 × 260 60 15
2 2 3.05 3.89 2.55 24.3 18.9 2.50 2.21 8.09 5.48 5.65 0.0507 19260 × 60 × 15 × 2.5 2.5 2.5 3.74 4.76 2.55 29.2 22.5 2.47 2.18 9.72 6.53 5.58 0.0965 224
60 × 60 × 20 × 3 60 60 20 3 3 4.63 5.90 2.71 34.1 28.9 2.40 2.21 11.4 8.78 5.91 0.171 384
BS
2994:1976
12©
BS
I 07-1999
Table 5 — Inwardly lipped channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia Radius of gyration
Elastic modulus
Shear centre
Torsion constant
Warping constant
D × B × C × t D B C t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
80 × 80 × 15 × 2 80 80 15 2 2 3.99 5.09 3.23 58.9 42.8 3.40 2.90 14.7 8.97 7.19 0.0667 641
80 × 80 × 20 × 3 80 80 20 3 3 6.04 7.70 3.40 84.6 65.7 3.32 2.92 21.2 14.3 7.49 0.225 1 170
80 × 80 × 25 × 480 80 25
4 4 8.12 10.3 3.56 107 88.9 3.22 2.93 26.8 20.0 7.76 0.535 1 94080 × 80 × 25 × 5 5 7.5 9.74 12.4 3.55 124 101 3.16 2.86 31.0 22.7 7.59 0.999 2 120
100 × 100 × 15 × 2 100 100 15 2 2 4.94 6.29 3.91 116 80.7 4.30 3.58 23.2 13.3 8.72 0.0827 1 720
100 × 100 × 20 × 3 100 100 20 3 3 7.45 9.50 4.08 169 124 4.22 3.62 33.8 21.0 9.03 0.279 2 980
100 × 100 × 25 × 4100 100 25
4 4 10.0 12.7 4.25 218 169 4.13 3.64 43.5 29.3 9.33 0.663 4 670100 × 100 × 25 × 5 5 7.5 12.1 15.4 4.23 256 195 4.07 3.56 51.1 33.8 9.16 1.25 5 210
BS
2994:1976
© B
SI 07-1999
13
Table 6 — Inwardly lipped channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus Shear centre
Torsion constant
Warping constant
D × B × C × t D B C t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
30 × 15 × 10 × 1.230 15 10
1.2 1.2 0.665 0.847 0.652 1.04 0.291 1.11 0.586 0.694 0.343 1.49 0.0039 1.0430 × 15 × 10 × 1.6 1.6 1.6 0.847 1.08 0.651 1.27 0.347 1.08 0.567 0.843 0.409 1.44 0.0088 1.19
40 × 20 × 10 × 1.240 20 10
1.2 1.2 0.853 1.09 0.792 2.58 0.649 1.54 0.773 1.29 0.537 1.84 0.0051 3.0940 × 20 × 10 × 1.6 1.6 1.6 1.10 1.40 0.790 3.21 0.792 1.52 0.752 1.61 0.654 1.79 0.0115 3.65
50 × 25 × 10 × 1.2 50 25 10 1.2 1.2 1.04 1.33 0.927 5.13 1.20 1.97 0.952 2.05 0.765 2.17 0.0062 7.6150 × 25 × 10 × 1.6 1.6 1.6 1.35 1.72 0.923 6.48 1.49 1.94 0.931 2.59 0.945 2.11 0.0142 9.1750 × 25 × 15 × 2 50 25 15 2 2 1.80 2.29 1.05 7.97 2.13 1.87 0.964 3.19 1.46 2.39 0.0294 18.6
50 × 40 × 10 × 1.250 40 10
1.2 1.2 1.32 1.69 1.59 7.27 3.73 2.08 1.49 2.91 1.54 3.59 0.0080 23.050 × 40 × 10 × 1.6 1.6 1.6 1.73 2.20 1.58 9.29 4.70 2.05 1.46 3.72 1.94 3.54 0.0183 28.3
50 × 40 × 15 × 250 40 15
2 2 2.27 2.89 1.74 11.4 6.57 1.99 1.51 4.57 2.90 3.88 0.0374 55.850 × 40 × 15 × 3 3 3 3.21 4.10 1.73 15.4 8.66 1.94 1.45 6.15 3.82 3.74 0.117 69.4
60 × 30 × 10 × 1.6 60 30 10 1.6 1.6 1.60 2.04 1.05 11.4 2.49 2.36 1.10 3.79 1.28 2.44 0.0170 20.060 × 30 × 15 × 2 60 30 15 2 2 2.11 2.69 1.19 14.2 3.55 2.30 1.15 4.73 1.96 2.73 0.0347 37.660 × 30 × 20 × 3
60 30 203 3 3.21 4.10 1.30 19.4 5.35 2.18 1.14 6.48 3.15 2.91 0.117 74.4
60 × 30 × 20 × 4 4 4 4.04 5.15 1.30 23.0 6.18 2.11 1.10 7.66 3.63 2.79 0.257 80.9
60 × 40 × 15 × 2 60 40 15 2 2 2.42 3.09 1.63 17.6 7.07 2.38 1.51 5.85 2.98 3.70 0.0401 73.960 × 40 × 20 × 3
60 40 203 3 3.69 4.70 1.76 24.3 10.8 2.28 1.51 8.10 4.81 3.92 0.135 148
60 × 40 × 20 × 4 4 4 4.67 5.95 1.76 29.2 12.7 2.22 1.46 9.75 5.68 3.79 0.300 166
70 × 25 × 10 × 1.6 70 25 10 1.6 1.6 1.60 2.04 0.791 14.5 1.68 2.66 0.908 4.14 0.984 1.86 0.0170 17.670 × 25 × 15 × 2 70 25 15 2 2 2.11 2.69 0.908 18.3 2.43 2.61 0.952 5.22 1.53 2.12 0.0347 31.770 × 25 × 20 × 3 70 25 20 3 3 3.21 4.10 1.01 25.3 3.67 2.49 0.947 7.23 2.46 2.28 0.117 59.1
BS
2994:1976
14©
BS
I 07-1999
Table 6 — Inwardly lipped channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus
Shear centre
Torsion constant
Warping constant
D × B × C × t D B C t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
70 × 30 × 15 × 2 70 30 15 2 2 2.27 2.89 1.11 20.6 3.77 2.67 1.14 5.88 1.99 2.59 0.0374 48.870 × 30 × 20 × 3 70 30 20 3 3 3.45 4.40 1.22 28.7 5.73 2.55 1.14 8.20 3.22 2.77 0.126 92.2
70 × 40 × 15 × 2 70 40 15 2 2 2.58 3.29 1.54 25.2 7.51 2.77 1.51 7.21 3.05 3.54 0.0427 95.970 × 40 × 20 × 3 70 40 20 3 3 3.92 5.00 1.67 35.4 11.5 2.66 1.52 10.1 4.93 3.76 0.144 18370 × 40 × 25 × 4 70 40 25 4 4 5.30 6.75 1.79 43.6 15.4 2.54 1.51 12.5 6.95 3.94 0.343 312
80 × 40 × 10 × 1.6 80 40 10 1.6 1.6 2.10 2.68 1.31 27.3 5.59 3.19 1.44 6.84 2.08 3.07 0.0224 72.080 × 40 × 15 × 2 80 40 15 2 2 2.74 3.49 1.46 34.5 7.90 3.15 1.51 8.63 3.10 3.39 0.0454 12280 × 40 × 20 × 3 80 40 20 3 3 4.16 5.30 1.58 49.0 12.2 3.04 1.51 12.3 5.02 3.60 0.153 22680 × 40 × 25 × 4 80 40 25 4 4 5.61 7.15 1.70 61.1 16.3 2.92 1.51 15.3 7.10 3.79 0.364 371
80 × 50 × 10 × 1.6 80 50 10 1.6 1.6 2.35 3.00 1.73 32.3 9.72 3.28 1.80 8.07 2.97 3.98 0.0252 12480 × 50 × 15 × 2 80 50 15 2 2 3.05 3.89 1.88 40.6 13.5 3.23 1.87 10.2 4.34 4.32 0.0507 20780 × 50 × 20 × 3 80 50 20 3 3 4.63 5.90 2.02 57.9 20.8 3.13 1.88 14.5 7.00 4.57 0.171 38480 × 50 × 25 × 4 80 50 25 4 4 6.24 7.95 2.15 72.7 28.2 3.02 1.88 18.2 9.89 4.78 0.407 635
90 × 40 × 10 × 1.6 90 40 10 1.6 1.6 2.23 2.84 1.24 35.9 5.82 3.56 1.43 7.99 2.11 2.94 0.0238 92.690 × 40 × 15 × 2 90 40 15 2 2 2.89 3.69 1.38 45.6 8.25 3.52 1.50 10.1 3.15 3.25 0.0481 15390 × 40 × 20 × 3 90 40 20 3 3 4.39 5.60 1.50 65.3 12.7 3.42 1.51 14.5 5.10 3.46 0.162 275
90 × 50 × 10 × 1.6 90 50 10 1.6 1.6 2.48 3.16 1.64 42.2 10.1 3.65 1.79 9.38 3.02 3.83 0.0265 16090 × 50 × 15 × 2 90 50 15 2 2 3.21 4.09 1.80 53.3 14.1 3.61 1.86 11.9 4.41 4.17 0.0534 25990 × 50 × 20 × 3 90 50 20 3 3 4.86 6.20 1.93 76.7 21.9 3.52 1.88 17.0 7.12 4.41 0.180 468
100 × 40 × 10 × 1.6 100 40 10 1.6 1.6 2.35 3.00 1.18 46.0 6.03 3.91 1.42 9.19 2.14 2.83 0.0252 116100 × 40 × 15 × 2 100 40 15 2 2 3.05 3.89 1.32 58.5 8.56 3.88 1.48 11.7 3.19 3.12 0.0507 188100 × 40 × 20 × 3 100 40 20 3 3 4.63 5.90 1.44 84.4 13.3 3.78 1.50 16.9 5.17 3.32 0.171 332
100 × 50 × 15 × 2 100 50 15 2 2 3.37 4.29 1.72 68.1 14.7 3.99 1.85 13.6 4.47 4.03 0.0561 319100 × 50 × 20 × 3 100 50 20 3 3 5.10 6.50 1.85 98.5 22.8 3.89 1.87 19.7 7.22 4.26 0.189 564100 × 50 × 25 × 4
100 50 254 4 6.87 8.75 1.97 126 30.9 3.79 1.88 25.1 10.2 4.47 0.449 891
100 × 50 × 25 × 5 5 7.5 8.17 10.4 1.96 143 34.3 3.70 1.82 28.5 11.3 4.31 0.833 936
100 × 60 × 15 × 2 100 60 15 2 2 3.68 4.69 2.13 77.7 22.9 4.07 2.21 15.5 5.92 4.94 0.0614 493100 × 60 × 20 × 3 100 60 20 3 3 5.57 7.10 2.28 113 35.4 3.98 2.23 22.5 9.52 5.20 0.207 871100 × 60 × 25 × 4
100 60 254 4 7.49 9.55 2.41 144 48.2 3.88 2.25 28.8 13.4 5.43 0.492 1 380
100 × 60 × 25 × 5 5 7.5 8.95 11.4 2.40 165 54.2 3.81 2.18 33.0 15.0 5.27 0.916 1 480
120 × 50 × 15 × 2 120 50 15 2 2 3.68 4.69 1.58 104 15.7 4.71 1.83 17.4 4.57 3.77 0.0614 464120 × 50 × 20 × 3 120 50 20 3 3 5.57 7.10 1.71 152 24.4 4.63 1.85 25.3 7.39 3.99 0.207 797120 × 50 × 25 × 4
120 50 254 4 7.49 9.55 1.83 196 33.3 4.53 1.87 32.6 10.5 4.19 0.492 1 220
120 × 50 × 25 × 5 5 7.5 8.95 11.4 1.81 224 37.0 4.44 1.80 37.4 11.6 4.03 0.916 1 290
BS
2994:1976
© B
SI 07-1999
15
Table 6 — Inwardly lipped channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus
Shear centre
Torsion constant
Warping constant
D × B × C × t B A C t r Cy About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sy K Iw
mm mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
120 × 60 × 20 × 3 120 60 20 3 3 6.04 7.70 2.11 173 37.9 4.74 2.22 28.8 9.76 4.90 0.225 1 230120 × 60 × 25 × 4
120 60 254 4 8.12 10.3 2.24 223 51.8 4.64 2.24 37.1 13.8 5.12 0.535 1 880
120 × 60 × 25 × 5 5 7.5 9.74 12.4 2.22 258 58.4 4.56 2.17 42.9 15.5 4.96 0.999 2 030
140 × 60 × 20 × 3 140 60 20 3 3 6.51 8.30 1.97 248 40.1 5.47 2.20 35.4 9.94 4.63 0.243 1 670140 × 60 × 25 × 4
140 60 254 4 8.75 11.1 2.10 322 55.0 5.38 2.22 46.0 14.1 4.85 0.577 2 510
140 × 60 × 25 × 5 5 7.5 10.5 13.4 2.08 375 62.1 5.29 2.15 53.5 15.8 4.69 1.08 2 720
150 × 50 × 20 × 3 150 50 20 3 3 6.28 8.00 1.53 259 26.3 5.69 1.81 34.6 7.58 3.64 0.234 1 250150 × 50 × 25 × 4
150 50 254 4 8.44 10.7 1.64 338 36.1 5.61 1.83 45.0 10.8 3.83 0.556 1 860
150 × 50 × 25 × 5 5 7.5 10.1 12.9 1.63 391 40.2 5.50 1.77 52.1 11.9 3.67 1.04 1 980
180 × 50 × 20 × 3 180 50 20 3 3 6.98 8.90 1.39 403 27.8 6.73 1.77 44.7 7.71 3.36 0.261 1 840180 × 50 × 25 × 4
180 50 254 4 9.38 11.9 1.50 528 38.4 6.65 1.79 58.6 11.0 3.53 0.620 2 680
180 × 50 × 25 × 5 5 7.5 11.3 14.4 1.48 615 42.8 6.53 1.72 68.3 12.2 3.38 1.17 2 880
180 × 80 × 20 × 3 180 80 20 3 3 8.40 10.7 2.49 544 88.5 7.13 2.88 60.4 16.1 5.91 0.315 5 650180 × 80 × 25 × 4
180 80 254 4 11.3 14.3 2.62 714 122 7.05 2.91 79.3 22.6 6.14 0.748 8 240
180 × 80 × 25 × 5 5 7.5 13.7 17.4 2.60 845 140 6.97 2.84 93.8 25.9 5.98 1.42 9 230
200 × 50 × 20 × 3 200 50 20 3 3 7.45 9.50 1.31 520 28.7 7.40 1.74 52.0 7.78 3.20 0.279 2 310200 × 50 × 25 × 4
200 50 254 4 10.0 12.7 1.42 684 39.6 7.33 1.76 68.4 11.1 3.36 0.663 3 340
200 × 50 × 25 × 5 5 7.5 12.1 15.4 1.40 800 44.3 7.21 1.70 80.0 12.3 3.21 1.25 3 610
200 × 80 × 20 × 3 200 80 20 3 3 8.87 11.3 2.36 695 91.6 7.84 2.85 69.5 16.3 5.68 0.333 7 100200 × 80 × 25 × 4
200 80 254 4 11.9 15.1 2.49 915 126 7.77 2.88 91.5 22.9 5.90 0.791 10 270
200 × 80 × 25 × 5 5 7.5 14.4 18.4 2.47 1 090 145 7.68 2.81 109 26.3 5.74 1.50 11 530
250 × 50 × 20 × 3 250 50 20 3 3 8.63 11.0 1.15 899 30.5 9.04 1.66 72.0 7.92 2.86 0.324 3 770250 × 50 × 25 × 4
250 50 254 4 11.6 14.7 1.25 1 190 42.2 8.98 1.69 95.2 11.3 3.00 0.769 5 380
250 × 50 × 25 × 5 5 7.5 14.1 17.9 1.24 1 400 47.2 8.85 1.62 112 12.6 2.86 1.46 5 860
250 × 80 × 20 × 3 250 80 20 3 3 10.0 12.8 2.10 1 170 98.1 9.58 2.77 93.9 16.6 5.19 0.378 11 630250 × 80 × 25 × 4
250 80 254 4 13.5 17.1 2.23 1 550 135 9.52 2.81 124 23.4 5.39 0.897 16 580
250 × 80 × 25 × 5 5 7.5 16.4 20.9 2.21 1 850 156 9.41 2.73 148 27.0 5.22 1.71 18 740
BS
2994:1976
16©
BS
I 07-1999
Table 7 — Outwardly lipped channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus
Shear centre
Torsion constant
Warping constant
B × A × C × t B A C t r Cx About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sx K Iw
mm mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
30 × 30 × 10 × 1.230 30 10
1.2 1.2 0.948 1.21 1.36 1.52 2.40 1.12 1.41 0.927 1.01 2.57 0.0057 1.4930 × 30 × 10 × 1.6 1.6 1.6 1.22 1.56 1.35 1.89 3.00 1.10 1.39 1.15 1.28 2.52 0.0129 1.74
35 × 35 × 10 × 1.235 35 10
1.2 1.2 1.09 1.39 1.53 2.35 3.62 1.30 1.61 1.19 1.37 3.02 0.0065 3.2635 × 35 × 10 × 1.6 1.6 1.6 1.41 1.80 1.53 2.94 4.56 1.28 1.59 1.49 1.76 2.97 0.0149 3.89
40 × 40 × 10 × 1.240 40 10
1.2 1.2 1.23 1.57 1.70 3.42 5.21 1.48 1.82 1.49 1.81 3.45 0.0074 6.5340 × 40 × 10 × 1.6 1.6 1.6 1.60 2.04 1.70 4.32 6.61 1.45 1.80 1.88 2.33 3.40 0.0170 7.9140 × 40 × 15 × 2 40 40 15 2 2 2.11 2.69 1.86 5.99 9.73 1.49 1.90 2.80 2.95 3.36 0.0347 10.140 × 40 × 20 × 3 40 40 20 3 3 3.21 4.10 2.00 8.97 16.6 1.48 2.01 4.48 4.48 3.11 0.117 16.4
50 × 50 × 10 × 1.6 50 50 10 1.6 1.6 1.98 2.52 2.04 8.18 12.5 1.80 2.23 2.76 3.73 4.24 0.0211 25.950 × 50 × 15 × 2 50 50 15 2 2 2.58 3.29 2.21 11.3 17.5 1.85 2.31 4.04 4.60 4.28 0.0427 30.950 × 50 × 20 × 3 50 50 20 3 3 3.92 5.00 2.36 17.1 28.5 1.85 2.39 6.48 6.79 4.12 0.144 44.0
60 × 60 × 10 × 1.6 60 60 10 1.6 1.6 2.35 3.00 2.38 13.8 21.1 2.14 2.65 3.81 5.51 5.05 0.0252 67.860 × 60 × 15 × 2 60 60 15 2 2 3.05 3.89 2.55 18.9 28.8 2.21 2.72 5.48 6.70 5.15 0.0507 80.060 × 60 × 20 × 3 60 60 20 3 3 4.63 5.90 2.71 28.9 45.8 2.21 2.79 8.78 9.74 5.06 0.171 10860 × 60 × 25 × 4 60 60 25 4 4 6.24 7.95 2.86 38.8 65.7 2.21 2.88 12.3 12.9 4.87 0.407 142
80 × 80 × 15 × 2 80 80 15 2 2 3.99 5.09 3.23 42.8 65.0 2.90 3.57 8.97 12.3 6.81 0.0667 36380 × 80 × 20 × 3 80 80 20 3 3 6.04 7.70 3.40 65.7 100 2.92 3.61 14.3 17.6 6.83 0.225 48680 × 80 × 25 × 4 80 80 25 4 4 8.12 10.3 3.56 88.9 140 2.93 3.67 20.0 22.9 6.75 0.535 59380 × 80 × 30 × 5 80 80 30 5 7.5 10.1 12.9 3.71 110 182 2.92 3.75 25.6 28.0 6.56 1.04 665
100 × 100 × 15 × 2 100 100 15 2 2 4.94 6.29 3.91 80.7 124 3.58 4.44 13.3 19.6 8.42 0.0827 1 160100 × 100 × 20 × 3 100 100 20 3 3 7.45 9.50 4.08 124 189 3.62 4.46 21.0 28.2 8.50 0.279 1 580100 × 100 × 25 × 4 100 100 25 4 4 10.0 12.7 4.25 169 258 3.64 4.50 29.3 36.4 8.50 0.663 1 930100 × 100 × 30 × 5
100 100 305 7.5 12.5 15.9 4.40 210 330 3.63 4.56 37.5 44.1 8.41 1.29 2 130
100 × 100 × 30 × 6 6 9 14.6 18.6 4.39 237 377 3.57 4.50 42.2 50.9 8.27 2.16 2 270
BS
2994:1976
© B
SI 07-1999
17
Table 8 — Outwardly lipped channels
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia
Radius of gyration
Elastic modulus
Shear centre
Torsion constant
Warping constant
B × A × C × t B A C t r Cx About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Sx K Iw
mm mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm cm4 cm6
40 × 50 × 10 × 1.6 40 50 10 1.6 1.6 1.85 2.36 2.17 7.52 7.79 1.79 1.82 2.66 2.74 4.37 0.0197 14.940 × 50 × 15 × 2 40 50 15 2 2 2.42 3.09 2.34 10.3 11.2 1.83 1.90 3.89 3.39 4.31 0.0401 19.140 × 50 × 20 × 3 40 50 20 3 3 3.69 4.70 2.50 15.6 18.6 1.82 1.99 6.23 5.03 4.04 0.135 31.2
40 × 60 × 15 × 2 40 60 15 2 2 2.74 3.49 2.83 16.2 12.6 2.16 1.90 5.12 3.82 5.28 0.0454 32.140 × 60 × 20 × 3 40 60 20 3 3 4.16 5.30 3.00 24.5 20.7 2.15 1.98 8.17 5.59 4.97 0.153 52.5
40 × 80 × 15 × 2 40 80 15 2 2 3.37 4.29 3.82 33.4 15.5 2.79 1.90 7.99 4.70 7.23 0.0561 73.240 × 80 × 20 × 3 40 80 20 3 3 5.10 6.50 4.00 50.6 24.8 2.79 1.95 12.7 6.70 6.88 0.189 119
50 × 30 × 10 × 1.250 30
10 1.2 1.2 1.14 1.45 1.14 1.86 6.88 1.13 2.18 1.00 2.03 2.41 0.0068 5.2950 × 30 × 10 × 1.6 1.6 1.6 1.48 1.88 1.14 2.32 8.72 1.11 2.15 1.25 2.61 2.36 0.0156 6.37
50 × 40 × 10 × 1.250 40
10 1.2 1.2 1.32 1.69 1.59 3.73 8.31 1.49 2.22 1.54 2.46 3.34 0.0080 11.450 × 40 × 10 × 1.6 1.6 1.6 1.73 2.20 1.58 4.70 10.6 1.46 2.20 1.94 3.17 3.29 0.0183 14.0
50 × 60 × 15 × 2 50 60 15 2 2 2.89 3.69 2.69 17.6 19.8 2.19 2.32 5.32 5.21 5.24 0.0481 51.750 × 60 × 20 × 3 50 60 20 3 3 4.39 5.60 2.85 26.8 31.8 2.19 2.38 8.51 7.58 5.07 0.162 74.550 × 60 × 25 × 4 50 60 25 4 4 5.92 7.55 3.00 35.8 46.5 2.18 2.48 11.9 10.1 4.78 0.385 108
50 × 80 × 15 × 2 50 80 15 2 2 3.52 4.49 3.65 36.1 24.4 2.84 2.33 8.30 6.42 7.18 0.0587 11750 × 80 × 20 × 3 50 80 20 3 3 5.33 6.80 3.83 54.9 38.5 2.84 2.38 13.2 9.16 6.99 0.198 17150 × 80 × 25 × 4 50 80 25 4 4 7.18 9.15 4.00 73.6 54.9 2.84 2.45 18.4 11.9 6.66 0.471 248
60 × 80 × 15 × 2 60 80 15 2 2 3.68 4.69 3.50 38.5 35.6 2.87 2.75 8.55 8.27 7.08 0.0614 17960 × 80 × 20 × 3 60 80 20 3 3 5.57 7.10 3.67 58.8 55.5 2.88 2.80 13.6 11.8 6.99 0.207 24760 × 80 × 25 × 4 60 80 25 4 4 7.49 9.55 3.84 79.1 78.3 2.88 2.86 19.0 15.4 6.77 0.492 328
80 × 100 × 15 × 2 80 100 15 2 2 4.62 5.89 4.17 74.5 77.2 3.56 3.62 12.8 14.6 8.73 0.0774 67080 × 100 × 20 × 3 80 100 20 3 3 6.98 8.90 4.35 114 118 3.58 3.65 20.2 20.7 8.75 0.261 91380 × 100 × 25 × 4 80 100 25 4 4 9.38 11.9 4.52 155 163 3.60 3.69 28.2 26.7 8.68 0.620 1 13080 × 100 × 30 × 5 80 100 30 5 7.5 11.7 14.9 4.68 191 210 3.58 3.75 36.0 32.3 8.47 1.21 1 290
BS
2994:1976
18©
BS
I 07-1999
Table 9 — Tee sections
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia Radius of gyration Elastic modulus Torsion constant
B × D × t B D t r About About About About About About KCx X–X Y–Y X–X Y–Y X–X Y–Y
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm4
25 × 15 × 125 15
1 1 0.396 0.504 0.449 0.110 0.131 0.467 0.510 0.105 0.105 0.001625 × 15 × 1.2 1.2 1.2 0.467 0.594 0.456 0.127 0.158 0.462 0.515 0.122 0.126 0.002825 × 15 × 1.6 1.6 1.6 0.599 0.763 0.472 0.156 0.211 0.453 0.526 0.152 0.169 0.0062
25 × 20 × 1
25 20
1 1 0.474 0.604 0.659 0.247 0.131 0.639 0.466 0.184 0.105 0.002025 × 20 × 1.2 1.2 1.2 0.561 0.714 0.667 0.287 0.158 0.634 0.471 0.215 0.127 0.003325 × 20 × 1.6 1.6 1.6 0.725 0.923 0.685 0.358 0.213 0.623 0.480 0.273 0.170 0.007625 × 20 × 2 2 2 0.877 1.12 0.703 0.419 0.268 0.612 0.490 0.323 0.215 0.0142
25 × 25 × 1
25 25
1 1 0.553 0.704 0.880 0.457 0.132 0.806 0.432 0.282 0.105 0.002325 × 25 × 1.2 1.2 1.2 0.655 0.834 0.889 0.534 0.159 0.800 0.436 0.332 0.127 0.003925 × 25 × 1.6 1.6 1.6 0.850 1.08 0.909 0.674 0.214 0.789 0.445 0.424 0.171 0.009025 × 25 × 2 2 2 1.03 1.32 0.928 0.796 0.271 0.777 0.454 0.507 0.217 0.0169
25 × 35 × 1
25 35
1 1 0.710 0.904 1.34 1.15 0.132 1.13 0.383 0.534 0.106 0.003025 × 35 × 1.2 1.2 1.2 0.843 1.07 1.35 1.35 0.160 1.12 0.386 0.631 0.128 0.005125 × 35 × 1.6 1.6 1.6 1.10 1.40 1.37 1.73 0.217 1.11 0.393 0.813 0.173 0.011725 × 35 × 2 2 2 1.35 1.72 1.40 2.07 0.276 1.10 0.401 0.982 0.221 0.0222
35 × 20 × 1
35 20
1 1 0.553 0.704 0.572 0.278 0.358 0.629 0.713 0.195 0.205 0.002335 × 20 × 1.2 1.2 1.2 0.655 0.834 0.580 0.325 0.431 0.624 0.718 0.229 0.246 0.003935 × 20 × 1.6 1.6 1.6 0.850 1.08 0.596 0.409 0.576 0.614 0.729 0.291 0.329 0.009035 × 20 × 2 2 2 1.03 1.32 0.611 0.482 0.723 0.605 0.740 0.347 0.413 0.0169
35 × 25 × 1
35 25
1 1 0.631 0.804 0.777 0.518 0.359 0.802 0.668 0.300 0.205 0.002635 × 25 × 1.2 1.2 1.2 0.749 0.954 0.785 0.607 0.431 0.797 0.672 0.354 0.246 0.004535 × 25 × 1.6 1.6 1.6 0.976 1.24 0.802 0.770 0.577 0.787 0.681 0.454 0.330 0.010335 × 25 × 2 2 2 1.19 1.52 0.819 0.916 0.725 0.777 0.691 0.545 0.414 0.0195
BS
2994:1976
© B
SI 07-1999
19
Table 9 — Tee sections
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia Radius of gyration Elastic modulus Torsion constant
B × D × t B D t r About About About About About About KCx X–X Y–Y X–X Y–Y X–X Y–Y
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm4
35 × 35 × 1
35 35
1 1 0.788 1.00 1.21 1.30 0.359 1.14 0.598 0.570 0.205 0.003335 × 35 × 1.2 1.2 1.2 0.938 1.19 1.22 1.53 0.432 1.13 0.602 0.674 0.247 0.005635 × 35 × 1.6 1.6 1.6 1.23 1.56 1.24 1.97 0.580 1.12 0.609 0.872 0.332 0.013035 × 35 × 2 2 2 1.51 1.92 1.26 2.37 0.731 1.11 0.617 1.06 0.417 0.0249
35 × 40 × 1
35 40
1 1 0.867 1.10 1.44 1.88 0.360 1.30 0.571 0.733 0.206 0.003635 × 40 × 1.2 1.2 1.2 1.03 1.31 1.45 2.21 0.433 1.30 0.574 0.868 0.247 0.006235 × 40 × 1.6 1.6 1.6 1.35 1.72 1.47 2.85 0.582 1.29 0.581 1.13 0.332 0.014435 × 40 × 2 2 2 1.66 2.12 1.49 3.44 0.733 1.27 0.588 1.37 0.419 0.0275
40 × 20 × 1
40 20
1 1 0.592 0.754 0.538 0.291 0.535 0.621 0.842 0.199 0.267 0.002540 × 20 × 1.2 1.2 1.2 0.702 0.894 0.545 0.340 0.642 0.617 0.847 0.234 0.321 0.004240 × 20 × 1.6 1.6 1.6 0.913 1.16 0.560 0.429 0.858 0.607 0.859 0.298 0.429 0.009640 × 20 × 2 2 2 1.11 1.42 0.575 0.506 1.07 0.598 0.871 0.355 0.537 0.0182
40 × 25 × 1
40 25
1 1 0.671 0.854 0.734 0.543 0.535 0.797 0.791 0.307 0.267 0.002840 × 25 × 1.2 1.2 1.2 0.796 1.01 0.742 0.636 0.643 0.792 0.796 0.362 0.321 0.004840 × 25 × 1.6 1.6 1.6 1.04 1.32 0.758 0.810 0.859 0.782 0.806 0.465 0.430 0.011040 × 25 × 2 2 2 1.27 1.62 0.774 0.965 1.08 0.772 0.816 0.559 0.539 0.0209
40 × 35 × 1
40 35
1 1 0.828 1.05 1.16 1.37 0.536 1.14 0.713 0.584 0.268 0.003540 × 35 × 1.2 1.2 1.2 0.985 1.25 1.17 1.61 0.644 1.13 0.716 0.691 0.322 0.005940 × 35 × 1.6 1.6 1.6 1.29 1.64 1.18 2.07 0.862 1.12 0.724 0.895 0.431 0.013740 × 35 × 2 2 2 1.58 2.02 1.20 2.50 1.08 1.11 0.733 1.09 0.541 0.0262
40 × 40 × 1
40 40
1 1 0.906 1.15 1.38 1.97 0.536 1.31 0.681 0.751 0.268 0.003840 × 40 × 1.2 1.2 1.2 1.08 1.37 1.39 2.32 0.644 1.30 0.685 0.890 0.322 0.006540 × 40 × 1.6 1.6 1.6 1.42 1.80 1.41 3.00 0.863 1.29 0.692 1.16 0.432 0.015140 × 40 × 2 2 2 1.74 2.22 1.43 3.62 1.09 1.28 0.700 1.41 0.543 0.0289
40 × 45 × 1
40 45
1 1 0.985 1.25 1.61 2.71 0.536 1.47 0.654 0.937 0.268 0.004140 × 45 × 1.2 1.2 1.2 1.17 1.49 1.62 3.21 0.645 1.46 0.657 1.11 0.322 0.007140 × 45 × 1.6 1.6 1.6 1.54 1.96 1.64 4.15 0.865 1.45 0.664 1.45 0.432 0.016540 × 45 × 2 2 2 1.90 2.42 1.66 5.02 1.09 1.44 0.671 1.77 0.544 0.0315
45 × 25 × 1
45 25
1 1 0.710 0.904 0.696 0.565 0.761 0.790 0.917 0.313 0.338 0.003045 × 25 × 1.2 1.2 1.2 0.843 1.07 0.704 0.663 0.914 0.785 0.922 0.369 0.406 0.005145 × 25 × 1.6 1.6 1.6 1.10 1.40 0.720 0.845 1.22 0.776 0.933 0.474 0.543 0.011745 × 25 × 2 2 2 1.35 1.72 0.735 1.01 1.53 0.766 0.944 0.571 0.680 0.0222
45 × 35 × 1
45 35
1 1 0.867 1.10 1.11 1.43 0.762 1.14 0.830 0.596 0.338 0.003645 × 35 × 1.2 1.2 1.2 1.03 1.31 1.12 1.68 0.915 1.13 0.834 0.706 0.407 0.006245 × 35 × 1.6 1.6 1.6 1.35 1.72 1.13 2.17 1.22 1.12 0.843 0.915 0.544 0.014445 × 35 × 2 2 2 1.66 2.12 1.15 2.61 1.53 1.11 0.851 1.11 0.682 0.0275
BS
2994:1976
20©
BS
I 07-1999
Table 9 — Tee sections
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia Radius of gyration Elastic modulus Torsion constant
B × D × t B D t r About About About About About About KCx X–X Y–Y X–X Y–Y X–X Y–Y
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm4
45 × 45 × 1
45 45
1 1 1.02 1.30 1.55 2.83 0.762 1.47 0.764 0.958 0.339 0.004345 × 45 × 1.2 1.2 1.2 1.22 1.55 1.56 3.35 0.916 1.47 0.768 1.14 0.407 0.007445 × 45 × 1.6 1.6 1.6 1.60 2.04 1.57 4.33 1.23 1.46 0.775 1.48 0.545 0.017145 × 45 × 2 2 2 1.98 2.52 1.59 5.26 1.54 1.44 0.782 1.81 0.684 0.0329
50 × 20 × 1
50 20
1 1 0.671 0.854 0.481 0.312 1.04 0.605 1.10 0.206 0.417 0.002850 × 20 × 1.2 1.2 1.2 0.796 1.01 0.488 0.365 1.25 0.600 1.11 0.241 0.501 0.004850 × 20 × 1.6 1.6 1.6 1.04 1.32 0.502 0.461 1.67 0.591 1.12 0.308 0.668 0.011050 × 20 × 2 2 2 1.27 1.62 0.517 0.547 2.09 0.581 1.14 0.368 0.837 0.0209
50 × 25 × 1
50 25
1 1 0.749 0.954 0.663 0.585 1.04 0.783 1.05 0.318 0.417 0.003150 × 25 × 1.2 1.2 1.2 0.891 1.13 0.670 0.686 1.25 0.778 1.05 0.375 0.501 0.005450 × 25 × 1.6 1.6 1.6 1.16 1.48 0.685 0.876 1.67 0.768 1.06 0.482 0.669 0.012450 × 25 × 2 2 2 1.43 1.82 0.700 1.05 2.09 0.759 1.07 0.582 0.838 0.0235
50 × 35 × 1
50 35
1 1 0.906 1.15 1.06 1.48 1.04 1.13 0.951 0.607 0.418 0.003850 × 35 × 1.2 1.2 1.2 1.08 1.37 1.07 1.75 1.25 1.13 0.955 0.719 0.501 0.006550 × 35 × 1.6 1.6 1.6 1.42 1.80 1.09 2.25 1.68 1.12 0.964 0.933 0.670 0.015150 × 35 × 2 2 2 1.74 2.22 1.10 2.72 2.10 1.11 0.973 1.13 0.840 0.0289
50 × 50 × 1
50 50
1 1 1.14 1.45 1.71 3.91 1.04 1.64 0.848 1.19 0.418 0.004850 × 50 × 1.2 1.2 1.2 1.36 1.73 1.72 4.63 1.26 1.63 0.851 1.41 0.502 0.008250 × 50 × 1.6 1.6 1.6 1.79 2.28 1.74 6.01 1.68 1.62 0.858 1.84 0.672 0.019250 × 50 × 2 2 2 2.21 2.82 1.76 7.32 2.11 1.61 0.865 2.26 0.843 0.036950 × 50 × 3 3 3 3.21 4.09 1.81 10.3 3.20 1.58 0.885 3.21 1.28 0.119
50 × 65 × 1
50 65
1 1 1.38 1.75 2.40 7.95 1.05 2.13 0.772 1.94 0.418 0.005850 × 65 × 1.2 1.2 1.2 1.64 2.09 2.41 9.44 1.26 2.12 0.775 2.31 0.503 0.010050 × 65 × 1.6 1.6 1.6 2.17 2.76 2.43 12.3 1.68 2.11 0.780 3.02 0.673 0.023350 × 65 × 2 2 2 2.68 3.42 2.45 15.1 2.12 2.10 0.787 3.72 0.846 0.044950 × 65 × 3 3 3 3.92 4.99 2.50 21.3 3.23 2.07 0.804 5.34 1.29 0.146
65 × 65 × 1
65 65
1 1 1.49 1.90 2.21 8.72 2.29 2.14 1.10 2.03 0.705 0.006365 × 65 × 1.2 1.2 1.2 1.79 2.27 2.22 10.4 2.75 2.13 1.10 2.42 0.847 0.010865 × 65 × 1.6 1.6 1.6 2.36 3.00 2.24 13.5 3.68 2.12 1.11 3.18 1.13 0.025365 × 65 × 2 2 2 2.92 3.72 2.26 16.6 4.61 2.11 1.11 3.91 1.42 0.048965 × 65 × 3 3 3 4.27 5.44 2.31 23.6 6.97 2.08 1.13 5.63 2.14 0.160
BS
2994:1976
© B
SI 07-1999
21
Table 9 — Tee sections
Designation Dimensions Mass/unit length
Area of section
Centre of gravity
Moment of inertia Radius of gyration Elastic modulus Torsion constant
B × D × t B D t r About About About About About About K
Cx X–X Y–Y X–X Y–Y X–X Y–Y
mm mm mm mm mm kg/m cm2 cm cm4 cm4 cm cm cm3 cm3 cm4
65 × 80 × 1
65 80
1 1 1.73 2.20 2.89 15.3 2.29 2.63 1.02 2.99 0.706 0.007365 × 80 × 1.2 1.2 1.2 2.07 2.63 2.90 18.2 2.76 2.63 1.02 3.56 0.848 0.012665 × 80 × 1.6 1.6 1.6 2.73 3.48 2.92 23.8 3.68 2.61 1.03 4.69 1.13 0.029465 × 80 × 2 2 2 3.39 4.32 2.94 29.2 4.62 2.60 1.03 5.78 1.42 0.056965 × 80 × 3 3 3 4.98 6.34 2.99 41.9 7.00 2.57 1.05 8.38 2.15 0.187
80 × 65 × 1.2
80 65
1.2 1.2 1.93 2.45 2.06 11.1 5.13 2.13 1.45 2.51 1.28 0.011780 × 65 × 1.6 1.6 1.6 2.55 3.24 2.08 14.6 6.84 2.12 1.45 3.30 1.71 0.027480 × 65 × 2 2 2 3.15 4.02 2.10 17.9 8.57 2.11 1.46 4.06 2.14 0.052980 × 65 × 3 3 3 4.62 5.89 2.14 25.6 12.9 2.08 1.48 5.86 3.23 0.173
80 × 80 × 1.2
80 80
1.2 1.2 2.21 2.81 2.72 19.5 5.13 2.63 1.35 3.70 1.28 0.013480 × 80 × 1.6 1.6 1.6 2.92 3.72 2.74 25.6 6.85 2.62 1.36 4.87 1.71 0.031580 × 80 × 2 2 2 3.62 4.62 2.76 31.5 8.57 2.61 1.36 6.01 2.14 0.060980 × 80 × 3 3 3 5.33 6.79 2.81 45.3 12.9 2.58 1.38 8.73 3.23 0.200
BS
2994:1976
22©
BS
I 07-1999
Table 10 — Zed sections
Designation Dimensions Mass/unit length
Area of section
Moment of inertia Radius of gyration
Angle Elastic modulus Product moment
of inertia
Torsion constant
Warping constant
D × B × t B D t r About X–X
AboutY–Y
About U–U
About V–V
About V–V
min. ! About X–X
AboutY–Y
About U–U
About V–V
About XY
K Iw
mm mm mm mm mm kg/m cm2 cm4 cm4 cm4 cm4 cm tan ! cm3 cm3 cm3 cm3 cm4 cm4 cm6
40 × 20 × 1.640 20
1.6 1.6 0.926 1.18 2.84 0.756 3.34 0.260 0.469 0.439 1.42 0.394 1.28 0.255 1.13 0.0098 1.67
40 × 20 × 2 2 2 1.13 1.44 3.38 0.917 3.99 0.306 0.461 0.445 1.69 0.482 1.54 0.305 1.37 0.0187 1.94
50 × 25 × 1.6
50 25
1.6 1.6 1.18 1.50 5.76 1.51 6.74 0.531 0.595 0.433 2.30 0.625 2.07 0.411 2.27 0.0126 5.37
50 × 25 × 2 2 2 1.45 1.84 6.93 1.85 8.15 0.634 0.586 0.439 2.77 0.769 2.50 0.497 2.76 0.0240 6.36
50 × 25 × 3 3 3 2.08 2.65 9.44 2.60 11.2 0.845 0.565 0.452 3.78 1.11 3.45 0.685 3.89 0.0767 8.27
50 × 30 × 1.6
50 30
1.6 1.6 1.30 1.66 6.70 2.66 8.55 0.808 0.698 0.560 2.68 0.910 2.37 0.575 3.30 0.0139 8.91
50 × 30 × 2 2 2 1.60 2.04 8.09 3.25 10.4 0.967 0.688 0.567 3.23 1.12 2.88 0.696 4.04 0.0267 10.6
50 × 30 × 3 3 3 2.31 2.95 11.1 4.64 14.4 1.30 0.664 0.584 4.44 1.63 4.02 0.960 5.72 0.0857 14.0
75 × 25 × 1.6
75 25
1.6 1.6 1.49 1.90 15.0 1.51 15.9 0.690 0.603 0.240 4.01 0.626 3.77 0.455 3.44 0.0160 14.0
75 × 25 × 2 2 2 1.84 2.34 18.3 1.85 19.3 0.833 0.596 0.241 4.87 0.770 4.58 0.555 4.20 0.0307 16.8
75 × 25 × 3 3 3 2.67 3.40 25.4 2.61 26.8 1.14 0.580 0.246 6.77 1.11 6.39 0.785 5.96 0.0992 22.5
75 × 40 × 2
75 40
2 2 2.31 2.94 26.3 7.91 31.5 2.68 0.955 0.471 7.00 2.03 6.23 1.33 11.1 0.0387 63.1
75 × 40 × 3 3 3 3.37 4.30 37.1 11.4 44.7 3.74 0.933 0.480 9.88 2.97 8.86 1.89 16.0 0.126 86.9
75 × 40 × 4 4 4 4.38 5.57 46.4 14.7 56.5 4.62 0.911 0.490 12.4 3.86 11.2 2.38 20.5 0.289 106
100 × 25 × 1.6
100 25
1.6 1.6 1.81 2.30 30.3 1.51 31.0 0.794 0.588 0.156 6.05 0.626 5.83 0.483 4.61 0.0194 27.2
100 × 25 × 2 2 2 2.23 2.84 36.9 1.85 37.8 0.963 0.582 0.157 7.38 0.771 7.11 0.592 5.64 0.0374 32.7
100 × 25 × 3 3 3 3.26 4.15 51.9 2.62 53.2 1.34 0.569 0.159 10.4 1.11 10.0 0.846 8.03 0.122 44.5
100 × 25 × 4 4 4 4.22 5.37 64.8 3.29 66.5 1.66 0.556 0.160 13.0 1.43 12.5 1.08 10.1 0.278 53.4
BS
2994:1976
© B
SI 07-1999
23
Table 10 — Zed sections
Designation Dimensions Mass/unit length
Area of section
Moment of inertia Radius of gyration
Angle Elastic modulus Product moment
of inertia
Torsion constant
Warping constant
D × B × t D B t r About X–X
AboutY–Y
About U–U
About V–V
About V–V
min. ! About X–X
AboutY–Y
About U–U
About V–V
About XY
K Iw
mm mm mm mm mm kg/m cm2 cm4 cm4 cm4 cm4 cm tan ! cm3 cm3 cm3 cm3 cm4 cm4 cm6
100 × 40 × 2100 40
2 2 2.70 3.44 51.3 7.92 55.9 3.29 0.977 0.310 10.3 2.03 9.43 1.43 14.9 0.0454 125100 × 40 × 3 3 3 3.96 5.05 73.1 11.4 79.9 4.64 0.959 0.315 14.6 2.97 13.5 2.05 21.6 0.149 174100 × 40 × 4 4 4 5.16 6.57 92.5 14.7 101 5.82 0.941 0.320 18.5 3.86 17.1 2.62 27.7 0.342 215
130 × 40 × 2
130 40
2 2 3.17 4.04 95.7 7.92 99.8 3.79 0.969 0.212 14.7 2.03 13.9 1.51 19.5 0.0534 229130 × 40 × 3 3 3 4.67 5.95 137 11.4 143 5.40 0.953 0.214 21.1 2.97 20.0 2.19 28.2 0.176 323130 × 40 × 4 4 4 6.10 7.77 175 14.7 183 6.84 0.938 0.216 27.0 3.87 25.6 2.82 36.4 0.406 403130 × 40 × 5 5 7.5 7.42 9.45 206 17.7 216 7.91 0.915 0.222 31.7 4.72 30.2 3.35 44.1 0.770 457
130 × 60 × 3130 60
3 3 5.61 7.15 186 40.1 211 15.2 1.46 0.382 28.6 6.85 25.8 4.66 65.2 0.212 1 010130 × 60 × 4 4 4 7.36 9.37 239 52.1 271 19.3 1.44 0.386 36.7 8.98 33.3 6.02 84.8 0.491 1 280130 × 60 × 5 5 7.5 8.99 11.5 284 63.5 325 22.6 1.41 0.395 43.7 11.0 39.9 7.20 103 0.937 1 490
150 × 40 × 3150 40
3 3 5.14 6.55 195 11.4 201 5.80 0.941 0.173 26.0 2.97 24.9 2.26 32.7 0.194 450150 × 40 × 4 4 4 6.73 8.57 249 14.7 257 7.37 0.927 0.174 33.3 3.87 31.9 2.92 42.1 0.449 564150 × 40 × 5 5 7.5 8.21 10.5 295 17.7 304 8.60 0.907 0.178 39.3 4.72 37.8 3.49 51.1 0.854 644
150 × 60 × 3150 60
3 3 6.08 7.75 260 40.1 283 16.7 1.47 0.310 34.6 6.85 31.8 4.82 75.5 0.230 1 420150 × 60 × 4 4 4 7.99 10.2 335 52.1 366 21.3 1.45 0.313 44.6 8.98 41.1 6.25 98.2 0.534 1 810150 × 60 × 5 5 7.5 9.78 12.5 400 63.5 439 25.1 1.42 0.320 53.4 11.0 49.3 7.51 120 1.02 2 120
BS
2994:1976
24©
BS
I 07-1999
Table 11 — Lipped zed sections
Designation Dimensions Mass/unit length
Area of section
Moment of inertia Radius of gyration
Angle Elastic modulus Product moment
of inertia
Torsion constant
Warping constant
D × B × C × t D B C t r About X–X
AboutY–Y
About U–U
About V–V
About V–V
min. ! About X–X
AboutY–Y
About U–U
About V–V
About XY
K Iw
mm mm mm mm mm mm kg/m cm2 cm4 cm4 cm4 cm4 cm tan ! cm3 cm3 cm3 cm3 cm4 cm4 cm6
120 × 45 × 20 × 1.6
120 45 20
1.6 1.6 2.98 3.80 82.7 19.4 94.5 7.55 1.41 0.397 13.8 4.38 13.5 2.87 29.8 0.0320 502120 × 45 × 20 × 2 2 2 3.68 4.69 101 23.2 115 9.07 1.39 0.393 16.8 5.28 16.5 3.45 36.1 0.0614 599120 × 45 × 20 × 2.5 2.5 2.5 4.52 5.76 122 27.6 139 10.8 1.37 0.389 20.3 6.31 20.2 4.11 43.2 0.117 707
130 × 50 × 20 × 1.6
130 50 20
1.6 1.6 3.23 4.12 107 25.3 122 9.80 1.54 0.401 16.4 5.15 15.9 3.39 38.8 0.0347 757130 × 50 × 20 × 2 2 2 3.99 5.09 130 30.5 149 11.8 1.52 0.397 20.0 6.22 19.6 4.09 47.0 0.0667 907130 × 50 × 20 × 2.5 2.5 2.5 4.91 6.26 158 36.3 180 14.1 1.50 0.393 24.3 7.45 23.9 4.88 56.5 0.128 1 070
140 × 50 × 20 × 1.6
140 50 20
1.6 1.6 3.36 4.28 127 25.3 142 10.2 1.54 0.360 18.1 5.15 17.6 3.48 42.0 0.0361 888140 × 50 × 20 × 2 2 2 4.15 5.29 155 30.5 173 12.3 1.53 0.357 22.2 6.22 21.7 4.20 51.0 0.0694 1 060140 × 50 × 20 × 2.5 2.5 2.5 5.11 6.51 188 36.3 210 14.7 1.50 0.353 26.9 7.45 26.6 5.01 61.3 0.133 1 260
150 × 50 × 20 × 2150 50 20
2 2 4.31 5.49 183 30.5 200 12.8 1.52 0.323 24.4 6.23 23.9 4.29 54.9 0.0721 1 240150 × 50 × 20 × 2.5 2.5 2.5 5.31 6.76 222 36.3 243 15.2 1.50 0.319 29.6 7.45 29.3 5.13 66.1 0.138 1 470
165 × 50 × 20 × 2165 50 20
2 2 4.54 5.79 229 30.5 246 13.4 1.52 0.282 27.8 6.23 27.4 4.42 60.8 0.0761 1 520165 × 50 × 20 × 2.5 2.5 2.5 5.60 7.14 279 36.3 299 16.0 1.50 0.278 33.8 7.45 33.7 5.28 73.2 0.146 1 800
180 × 60 × 20 × 2
180 60 20
2 2 5.09 6.49 314 49.0 342 20.8 1.79 0.310 34.9 8.31 34.0 5.84 91.0 0.0854 2 820180 × 60 × 20 × 2.5 2.5 2.5 6.29 8.01 383 58.8 417 25.0 1.77 0.307 42.6 10.0 41.8 7.01 110 0.164 3 360180 × 60 × 20 × 3 3 3 7.45 9.50 450 67.5 488 28.8 1.74 0.304 49.9 11.5 49.3 8.08 128 0.279 3 850
BS
2994:1976
© B
SI 07-1999
25
Table 11 — Lipped zed sections
Designation Dimensions Mass/unit length
Area of section
Moment of inertia Radius of gyration
Angle Elastic modulus Product moment
of inertia
Torsion constant
Warping constant
D × B × C × t D B C t r About X–X
AboutY–Y
About U–U
About V–V
About V–V
min. ! About X–X
AboutY–Y
About U–U
About V–V
About XY
K Iw
mm mm mm mm mm mm kg/m cm2 cm4 cm4 cm4 cm4 cm tan ! cm3 cm3 cm3 cm3 cm4 cm4 cm6
190 × 60 × 20 × 2
190 60 20
2 2 5.25 6.69 357 49.0 384 21.4 1.79 0.287 37.5 8.31 36.7 5.93 96.3 0.0881 3 170
190 × 60 × 20 × 2.5 2.5 2.5 6.48 8.26 436 58.8 469 25.7 1.76 0.284 45.9 10.0 45.2 7.12 117 0.169 3 790
190 × 60 × 20 × 3 3 3 7.69 9.80 511 67.6 549 29.6 1.74 0.281 53.8 11.5 53.3 8.21 135 0.288 4 340
200 × 60 × 20 × 2
200 60 20
2 2 5.41 6.89 403 49.0 430 21.9 1.78 0.267 40.3 8.31 39.5 6.02 102 0.0907 3 550
200 × 60 × 20 × 2.5 2.5 2.5 6.68 8.51 493 58.8 525 26.3 1.76 0.264 49.3 10.0 48.6 7.23 123 0.175 4 240
200 × 60 × 20 × 3 3 3 7.92 10.1 578 67.6 615 30.3 1.73 0.261 57.8 11.5 57.5 8.33 143 0.297 4 860
215 × 75 × 20 × 2.5215 75 20
2.5 2.5 7.56 9.64 670 107 732 45.0 2.16 0.314 62.4 14.4 60.4 10.2 196 0.198 8 510
215 × 75 × 20 × 3 3 3 8.98 11.4 789 123 860 52.1 2.13 0.311 73.4 16.8 71.5 11.8 229 0.338 9 810
230 × 75 × 25 × 2.5 2.5 2.5 8.05 10.3 807 120 876 51.3 2.24 0.301 70.2 16.2 68.5 11.5 227 0.211 11 270
230 × 75 × 25 × 3230 75 25
3 3 9.57 12.2 951 139 1 030 59.7 2.21 0.298 82.7 18.9 81.1 13.3 266 0.360 13 050
230 × 75 × 25 × 4 4 4 12.5 15.9 1 220 173 1 320 74.6 2.16 0.293 106 23.7 105 16.7 336 0.833 16 140
250 × 75 × 25 × 3250 75 25
3 3 10.0 12.8 1 160 139 1 240 62.2 2.20 0.264 92.8 18.9 91.4 13.7 290 0.378 15 670
250 × 75 × 25 × 4 4 4 13.1 16.7 1 490 173 1 590 77.7 2.15 0.259 119 23.7 119 17.1 367 0.876 19 400
BS
2994:1976
26©
BS
I 07-1999
Table 12 — Plain channels back to back
S cg = distance between centroids such that lyy = lxx
Designation Dimensions Mass/unit length
Area of section
Moment of inertia Radius of gyration Elastic modulus Warping Constant
Centroid centres when
Iyy = IxxD × 2B × t D 2B t r About
X–XAbout
Y–YAbout
X–XAbout
Y–YAbout
X–XAbout
Y–YIw Scg
mm mm mm mm mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm6 cm
100 × 80 × 1.6
100 80
1.6 1.6 4.36 5.56 83.8 13.7 3.88 1.57 16.8 3.42 291 7.36100 × 80 × 2 2 2 5.41 6.89 103 17.1 3.86 1.58 20.5 4.28 349 7.32100 × 80 × 3 3 3 7.92 10.1 146 25.8 3.81 1.60 29.2 6.44 470 7.21100 × 80 × 4 4 4 10.3 13.1 185 34.5 3.75 1.62 37.0 8.62 560 7.10
120 × 100 × 3120 100
3 3 9.81 12.5 268 50.2 4.63 2.00 44.6 10.0 1 410 8.72120 × 100 × 4 4 4 12.8 16.3 342 67.1 4.57 2.03 57.0 13.4 1 720 8.62120 × 100 × 5 5 7.5 15.6 19.9 404 84.2 4.51 2.06 67.4 16.8 1 910 8.48
150 × 100 × 3150 100
3 3 11.2 14.3 455 50.3 5.64 1.87 60.6 10.1 2 230 10.9150 × 100 × 4 4 4 14.7 18.7 584 67.2 5.58 1.89 77.9 13.4 2 730 10.8150 × 100 × 5 5 7.5 18.0 22.9 695 84.5 5.51 1.92 92.7 16.9 3 080 10.6
180 × 100 × 3180 100
3 3 12.6 16.1 706 50.3 6.62 1.77 78.5 10.1 3 240 12.9180 × 100 × 5 5 7.5 20.3 25.9 1 090 84.7 6.48 1.81 121 16.9 4 520 12.7
200 × 100 × 4200 100
4 4 17.9 22.7 1 180 67.5 7.20 1.72 118 13.5 4 950 14.1200 × 100 × 5 5 7.5 21.9 27.9 1 420 84.9 7.12 1.74 142 17.0 5 640 14.0200 × 100 × 6 6 9 25.9 33.0 1 640 103 7.05 1.76 164 20.5 6 180 13.8
BS
2994:1976
© B
SI 07-1999
27
Table 12 — Plain channels back to backScg = distance between centroids such that Iyy = Ixx
Designation Dimensions Mass/unit length
Area of section
Moment of inertia
Radius of gyration
Elastic modulus Warping Constant
Centroid centres when Iyy = Ixx
D × 2B × t D 2B t r About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Iw Scg
mm mm mm mm mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm6 cm
200 × 160 × 4
200 160
4 4 21.6 27.5 1 640 274 7.72 3.15 164 34.2 22 360 14.6
200 × 160 × 5 5 7.5 26.6 33.9 1 990 343 7.65 3.18 199 42.9 26 290 14.5
200 × 160 × 6 6 9 31.5 40.2 2 320 412 7.60 3.20 232 51.5 29 760 14.4
250 × 100 × 4
250 100
4 4 21.0 26.7 2 060 67.7 8.78 1.59 165 13.5 7 820 17.4
250 × 100 × 5 5 7.5 25.8 32.9 2 490 85.3 8.69 1.61 199 17.1 8 970 17.2
250 × 100 × 6 6 9 30.6 39.0 2 890 103 8.62 1.63 232 20.7 9 900 17.0
250 × 160 × 4
250 160
4 4 24.8 31.5 2 790 274 9.40 2.95 223 34.3 35 280 18.2
250 × 160 × 5 5 7.5 30.5 38.9 3 390 343 9.33 2.97 271 42.9 41 670 18.0
250 × 160 × 6 6 9 36.3 46.2 3 970 413 9.27 2.99 317 51.6 47 360 17.9
BS
2994:1976
28©
BS
I 07-1999
Table 13 — Inwardly lipped channels back to back
Scg = distance between centroids such that Iyy = Ixx
Designation Dimensions Mass/unit length
Area of section
Moment of inertia Radius of gyration
Elastic modulus
Warping constant
Centroid centres when Iyy = Ixx
D × 2B × C × t D 2B C t r AboutX–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Iw Scg
mm mm mm mm mm mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm6 cm
100 × 80 × 10 × 1.6 100 80 10 1.6 1.6 4.71 6.00 91.9 20.4 3.91 1.84 18.4 5.10 482 7.30
100 × 80 × 15 × 2 100 80 15 2 2 6.10 7.77 117 30.6 3.88 1.98 23.4 7.64 759 7.17
100 × 80 × 20 × 3 100 80 20 3 3 9.26 11.8 169 50.8 3.78 2.08 33.7 12.7 1 270 6.95
100 × 100 × 15 × 2 100 100 15 2 2 6.73 8.57 136 54.6 3.99 2.52 27.2 10.9 1 360 7.06
100 × 100 × 20 × 3 100 100 20 3 3 10.2 13.0 197 89.9 3.89 2.63 39.4 18.0 2 270 6.83
100 × 100 × 25 × 4 100 100 25 4 4 13.7 17.5 251 130 3.79 2.73 50.2 26.0 3 340 6.58
100 × 100 × 25 × 5 100 100 25 5 7.5 16.3 20.8 285 149 3.70 2.67 57.0 29.7 3 440 6.45
120 × 100 × 15 × 2 120 100 15 2 2 7.36 9.37 208 54.6 4.71 2.41 34.7 10.9 1 930 8.69
120 × 100 × 20 × 3 120 100 20 3 3 11.1 14.2 304 90.0 4.63 2.52 50.7 18.0 3 170 8.48
120 × 100 × 25 × 4120 100 25
4 4 15.0 19.1 392 130 4.53 2.61 65.3 26.0 4 620 8.25
120 × 100 × 25 × 5 5 7.5 17.9 22.8 449 149 4.44 2.55 74.8 29.7 4 780 8.11
150 × 100 × 20 × 3 150 100 20 3 3 12.6 16.0 519 90.0 5.69 2.37 69.1 18.0 4 820 10.8
150 × 100 × 25 × 4150 100 25
4 4 16.9 21.5 675 130 5.61 2.46 90.0 26.1 6 930 10.6
150 × 100 × 25 × 5 5 7.5 20.3 25.8 781 149 5.50 2.40 104 29.8 7 220 10.4
180 × 100 × 20 × 3 180 100 20 3 3 14.0 17.8 805 90.1 6.73 2.25 89.5 18.0 6 810 13.0
180 × 100 × 25 × 4180 100 25
4 4 18.8 23.9 1 060 130 6.65 2.34 117 26.1 9 720 12.8
180 × 100 × 25 × 5 5 7.5 22.6 28.8 1 230 149 6.53 2.28 137 29.8 10 170 12.6
BS
2994:1976
© B
SI 07-1999
29
Table 13 — Inwardly lipped channels back to backScg = distance between centroids such that Iyy = Ixx
Designation Dimensions Mass/unit length
Area of section
Moment of inertia
Radius of gyration
Elastic modulus
Warping constant
Centroid centres when
Iyy = Ixx
D × 2B × C × t D 2B C t r About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
Iw Scg
mm mm mm mm mm mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm6 cm
200 × 100 × 20 × 3 200 100 20 3 3 14.9 19.0 1 040 90.1 7.40 2.18 104 18.0 8 330 14.4
200 × 100 × 25 × 4200 100 25
4 4 20.0 25.5 1 370 130 7.33 2.26 137 26.1 11 840 14.2
200 × 100 × 25 × 5 5 7.5 24.2 30.8 1 600 149 7.21 2.20 160 29.9 12 420 14.0
200 × 160 × 20 × 3 200 100 20 3 3 17.7 22.6 1 390 309 7.84 3.70 139 38.7 29 520 14.6
200 × 160 × 25 × 4200 160 25
4 4 23.8 30.3 1 830 441 7.77 3.81 183 55.1 41 780 14.4
200 × 160 × 25 × 5 5 7.5 28.9 36.8 2 170 516 7,68 3.74 217 64.4 46 210 14.3
250 × 100 × 20 × 3 250 100 20 3 3 17.3 22.0 1 800 90.2 9.04 2.03 144 18.0 12 790 17.8
250 × 100 × 25 × 4250 100 25
4 4 23.2 29.5 2 380 131 8.98 2.11 190 26.1 18 060 17.6
250 × 100 × 25 × 5 5 7.5 28.1 35.8 2 800 150 8.85 2.05 224 30.0 19 030 17.4
250 × 160 × 20 × 3 250 160 20 3 3 20.1 25.6 2 350 310 9.58 3.48 188 38.7 45 590 18.3
250 × 160 × 25 × 4250 160 25
4 4 26.9 34.3 3 110 441 9.52 3.59 248 55.1 64 170 18.2
250 × 160 × 25 × 5 5 7.5 32.8 41.8 3 700 516 9.41 3.51 296 64.5 71 210 18.0
BS
2994:1976
30©
BS
I 07-1999
Table 14 — Inwardly lipped channels lip to lip
Scg = distance between centroids such that Iyy = Ixx
Designation Dimensions Mass/unit length
Area of section
Moment of inertia
Radius of gyration
Elastic modulus Torsion constant
Centroid centres when
Iyy = Ixx
D × 2B × C × t D 2B C t r About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
K Scg
mm mm mm mm mm mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm4 cm
100 × 80 × 10 × 1.6 100 80 10 1.6 1.6 4.71 6.00 91.9 59.7 3.91 3.16 18.4 14.9 108 7.30
100 × 80 × 15 × 2 100 80 15 2 2 6.10 7.77 117 73.1 3.88 3.07 23.4 18.3 133 7.17
100 × 80 × 20 × 3 100 80 20 3 3 9.26 11.8 169 104 3.78 2.97 33.7 26.0 193 6.95
100 × 100 × 15 × 2 100 100 15 2 2 6.73 8.57 136 122 3.99 3.77 27.2 24.4 189 7.06
100 × 100 × 20 × 3 100 100 20 3 3 10.2 13.0 197 175 3.89 3.67 39.4 34.9 275 6.83
100 × 100 × 25 × 4 100 100 25 4 4 13.7 17.5 251 222 3.79 3.56 50.2 44.4 356 6.58
100 × 100 × 25 × 5 100 100 25 5 7.5 16.3 20.8 285 261 3.70 3.54 57.0 52.2 434 6.45
120 × 100 × 15 × 2 120 100 15 2 2 7.36 9.37 208 141 4.71 3.88 34.7 28.2 249 8.69
120 × 100 × 20 × 3 120 100 20 3 3 11.1 14.2 304 203 4.63 3.78 50.7 40.6 363 8.48
120 × 100 × 25 × 4120 100 25
4 4 15.0 19.1 392 259 4.53 3.68 65.3 51.8 470 8.25
120 × 100 × 25 × 5 5 7.5 17.9 22.8 449 306 4.44 3.66 74.8 61.2 576 8.11
150 × 100 × 20 × 3 150 100 20 3 3 12.6 16.0 519 245 5.69 3.92 69.1 49.0 502 10.8
150 × 100 × 25 × 4150 100 25
4 4 16.9 21.5 675 314 5.61 3.82 90.0 62.9 653 10.6
150 × 100 × 25 × 5 5 7.5 20.3 25.8 781 374 5.50 3.81 104 74.8 801 10.4
180 × 100 × 20 × 3 180 100 20 3 3 14.0 17.8 805 287 6.73 4.02 89.5 57.5 648 13.0
180 × 100 × 25 × 4180 100 25
4 4 18.8 23.9 1 060 370 6.65 3.93 117 73.9 844 12.8
180 × 100 × 25 × 5 5 7.5 22.6 28.8 1 230 442 6.53 3.92 137 88.3 1 040 12.6
BS
2994:1976
© B
SI 07-1999
31
Table 14 — Inwardly lipped channels lip to lipScg = distance between centroids such that Iyy = Ixx
Designation Dimensions Mass/unit length
Area of section
Moment of inertia
Radius of gyration
Elastic modulus Torsion constant
Centroid centres when
Iyy = Ixx
D × 2B × C × t D 2B C t r About X–X
AboutY–Y
About X–X
AboutY–Y
About X–X
AboutY–Y
K Scg
mm mm mm mm mm mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm4 cm
200 × 100 × 20 × 3 200 100 20 3 3 14.9 19.0 1 040 316 7.40 4.08 104 63.1 748 14.4
200 × 100 × 25 × 4200 100 25
4 4 20.0 25.5 1 370 406 7.33 3.99 137 81.3 974 14.2
200 × 100 × 25 × 5 5 7.5 24.2 30.8 1 600 487 7.21 3.98 160 97.4 1 200 14.0
200 × 160 × 20 × 3 200 160 20 3 3 17.7 22.6 1 390 901 7.84 6.31 139 113 1 630 14.6
200 × 160 × 25 × 4200 160 25
4 4 23.8 30.3 1 830 1 170 7.77 6.22 183 146 2 130 14.4
200 × 160 × 25 × 5 5 7.5 28.9 36.8 2 170 1 420 7.68 6.20 217 177 2 640 14.3
250 × 100 × 20 × 3 250 100 20 3 3 17.3 22.0 1 800 386 9.04 4.19 144 77.3 1 000 17.8
250 × 100 × 25 × 4250 100 25
4 4 23.2 29.5 2 380 499 8.98 4.11 190 99.7 1 310 17.6
250 × 100 × 25 × 5 5 7.5 28.1 35.8 2 800 600 8.85 4.09 224 120 1 610 17.4
250 × 160 × 20 × 3 250 160 20 3 3 20.1 25.6 2 350 1 090 9.58 6.51 188 136 2 240 18.3
250 × 160 × 25 × 4250 160 25
4 4 26.9 34.3 3 110 1 410 9.52 6.42 248 177 2 940 18.2
250 × 160 × 25 × 5 5 7.5 32.8 41.8 3 700 1 720 9.41 6.41 296 215 3 640 18.0
BS 2994:1976
32 © BSI 07-1999
Appendix A Basis of calculation for reduction factors
As described in clause 3, slight thinning at the corners occurs when steel strip is cold roll formed. The actual geometrical properties are therefore different from the theoretical properties that would be calculated if no allowance were made for this thinning effect.The properties shown in the tables in this standard are the more accurate values, an allowance for the thinning at the corners having been made in accordance with the following formula:
wheretred is the reduced corner thickness (see diagram)
r is the internal radius (= t for sections up to and including 4 mm thick and = 1"t for sections over 4 mm up to and including 6 mm thick)t is the unreduced thickness# is the reduction factor
The reduction factor, #, is taken as 0.30 for and 0.35 for
The mean radius of curvature, rm, as used in the calculations is given by:
rm = r + 0.5tThere is a somewhat similar thinning effect in the case of the radii at the top of tee sections. This has been allowed for in the calculations of the properties tabulated in this standard, although the effect in this case is, in fact, very small indeed.
tredr # t+r 0.5t+--------------------
t =
rt-- 1.0= r
t-- 1.5.=
BS 2994:1976
© BSI 07-1999
Publication referred to
Addendum No. 1 (1975) to BS 449-2, The use of cold formed steel sections in building.
BS 2994:1976
BSI389 Chiswick High RoadLondonW4 4AL
BSI — British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400.
BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048.
Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI.
This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.
If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
Top Related