1
1 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
EOSC 547:
Tunnelling & Underground Design
Topic 8: Brittle Fracture &
Stress-Controlled Failure
2 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Brittle –vs- Plastic Failure Mechanisms
2
3 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Spalling and Rockburst in Tunnelling
Kaiser et al. (2000)
4 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Stress Driven Spalling
3
5 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Stress Driven Spalling in Tunnelling - Issues
Falling slabs of rock a hazard to workers.
Problem for TBM as gripper pads cannotbe seated on the side wall.
6 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Stress Driven Spalling and Popping
4
7 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Rockbursting
8 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Rockbursting – StrainburstsRockburst: A sudden and violent failure of rock where rock fragments are ejected into the excavation. Energy is released as seismic energy radiated in the form of strain waves.
Strainburst: A self-initiated rockburst that develops due to a disequilibrium between high stresses and rock strength (i.e. dynamic unstable fracturing).
Usually occurs after blasting, as face is unable to adjust to the immediately stress increaseImmediate unloading of confinement from a triaxial to uniaxial stress condition, stored energy released as seismic energyCommonly occurs when drifting through contact between a brittle and relative soft rock (i.e. highly dependent on local mine rock stiffness)
5
9 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Rockbursting – Slip BurstsSlip burst: Slip bursts are characterized as a stick-slip shear movement on a discontinuity. These bursts are less likely to be triggered by a particular blast, and more likely to occur afterwards. Slip occurs when the ratio of shear to normal (effective) stress along the fault plane reaches a critical value (its shear strength).
Slip bursts at the Lucky Friday Mine.
Similar to mechanics of an earthquakeFault slip typically intersects the mine openingsIn most cases, mining activity causes slip by removing normal stress, although some local intensification of shear stress may also occurChanges in stress along a fault are often linked to mine activities by time-dependent deformation processes. These time-dependent processes can act over long periods of time, regardless of continued mining
Whyatt et al. (1997)
10 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
AECL’s Underground Research Laboratory
240 m Level
3 1
420 m Level Mar
tin
(199
7)
6
11 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
AECL’s URL – Brittle Failure
300mm diameter
1.2m diameterMartin (1997)
12 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Failure Criterion in Solid Mechanics
To understand the mechanisms at work leading to stress-induced ground control problems (spalling & bursting), we need to understand the basic principals of rock strength and brittle fracture processes.
Traditionally, there have been two approaches to analyzing rock strength:
experimental approach(i.e. phenomenological)
stress based
energy basedstrain based
mechanistic approach
7
13 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Analysis of Rock Strength
Phenomenological Approach
Relies on generalization of large scale observations.
Mechanistic Approach
Derives its theories from elements of fracture at the microscopic scale.
• Maximum Stress theory• Tresca theory• Coulomb theory• Mohr-Coulomb failure criterion• Hoek-Brown failure criterion
Theories include: Theories include:
• Griffith Crack theory• Linear Elastic Fracture
Mechanics (LEFM)
14 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Failure in ShearLab testing and field observations suggest that a shear failure criterion may be more applicable than a maximum stress criterion. In 2-D, the maximum shear stress is related to the difference in the major and minor principal stresses (i.e. deviatoric stress).
8
15 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Mohr-Coulomb Failure Criterion
1
2
345° + /2
n
failure occurs if :max > c + tan
90° + c
123t
tensioncutoff
16 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Mohr-Coulomb: Mechanistic PerspectiveThe Mohr-Coulomb criterion is widely applied for describing shear failure of rock. However, mechanistically speaking:
- Friction develops only on differential movement. Such movement can take place freely in a cohesionless material, but hardly in a cohesive one like rock prior to the development of a failure plane. In other words, mobilization of friction only becomes a factor once a failure plane is in the latter stages of development;
- Many brittle failures observed in the lab and underground appear to be largely controlled by the development of microfractures. Since these fractures initiate on a microscopic scale at stresses below the peak strength, the dismissal of all processes undetectable to the naked eye and prior to peak strength leaves the phenomenological approach lacking.
This is not to say that phenomenological approaches like Mohr-Coulomb are not useful. Remember: Mohr-Coulomb is the most widely used failure criterion, but its limitations need to be recognized.
9
17 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Analysis of Brittle Rock Strength
Phenomenological Approach
Relies on generalization of large scale observations.
Mechanistic Approach
Derives its theories from elements of fracture at the microscopic scale.
• Maximum Stress theory• Tresca theory• Coulomb theory• Mohr-Coulomb failure criterion• Hoek-Brown failure criterion
Theories include: Theories include:
• Griffith Crack theory• Linear Elastic Fracture
Mechanics (LEFM)
18 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Mechanistic Brittle Fracture Theories
F
ro
r
Fmax … on extension, the structure fractures where the interatomic force is exhausted (i.e. the theoretical tensile strength)
F
F
rormax
Fmax At the atomic level, the development of interatomic forces is controlled by the atomic spacing which can be altered by means of external loading …
bonds become unstable
ten
sion
ro
10
19 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Mechanistic Brittle Fracture Theories
F
ro
ten
sion
r
… displacement is countered by an inexhaustible repulsive force
F
roC ≈ ∞
F
com
pre
ssio
n
Fmax
attr
acti
onre
pu
lsio
nro
F
In compression …
Thus, interatomic bonds will only break when pulled apart (i.e. in tension).
20 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Theoretical Strength
F
F
rmax
F
ro
Fmax
Strength is therefore a function of the cohesive forces between atoms, where if F > Fmax, then the interatomic bonds will break. As such, we can derive the following:
Now for most rocks, the Young’s modulus, E, is of the order 10-100 GPa. If so, then the theoretical tensile strength of these rocks should be 1-10 GPa.
ro
ten
sion
r
com
pre
ssio
n
Fmax
attr
acti
onre
pu
lsio
n
ro
However, this is at least 1000 timesgreater than the true tensile strength of rock!!!
11
21 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Griffith TheoryTo explain this discrepancy, Griffith (1920) postulated that in the case of a linear elastic material, brittle fracture is initiated through tensile stress concentrations at the tips of small, thin cracks randomly distributed within an otherwise isotropic material.
22 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Crack Propagation in CompressionUnder uniaxial compressive loading conditions, the highest tangential stress concentration on an elliptical crack boundary was inclined 30°to the major principal stress. As these cracks develop, they will rotate to align themselves with the major principal stress, 1.
Lajtai (1971)
12
23 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Crack Propagation in CompressionExperimentally, it has been shown that brittle fractures propagate in the direction of 1. Cracks develop in this way to allow the newly forming crack faces to open/dilate in the direction of least resistance (i.e. normal to 1 in the direction of 3).
This is most easily accommodated in uniaxial compression since 3 = 0. For example, along a free surface!!
1
3
24 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Linear Elastic Fracture Mechanics
1) Associated with a crack tip in a loaded material is a stress intensity factor, KI, corresponding to the induced stress state surrounding the crack (and likewise KII and KIII depending on the crack displacement mode).
Griffith’s energy instability concept forms the basis for the study of fracture mechanics, in which the loading applied to a crack tip is analyzed to determine whether or not the crack will propagate.
4) The crack will continue to propagate as long as the above expression is met, and won’t stop until: KI < KIc.
2) For a given crack, the boundary material will have a critical stress intensity factor, KIc, corresponding to the material strength at the crack tip.
3) The criterion for crack propagation can then be written as KI ≥ KIc. Laboratory testing for the KIc parameter is referred to as fracture toughness testing.
Ingraffea (1987)
tensile in-planeshear
out of planetearing
13
25 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Crack Interaction & Coalescence
crackinteraction
crack tipstressesincrease
cracks propagate& interact
Eberhardt et al. (1998a)
cracks coalesce;energy released
yielding ofbridgingmaterial
localization& developmentof rupture
surface
26 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Damage Around an Underground Excavation
1 = 55 MPa
3 = 14 MPa final shape
stages in notchdevelopment
microseismicevents
3
1
420 m LevelMartin (1997)
14
27 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Failure Around Underground Excavations
max = 0.4 UCS
Martin et al. (1999)Observations from underground mining in massive brittle rocks suggest that failure initiates when the maximum tangential boundary stress reaches approximately 40% of the unconfined compressive strength.
ci = 0.4 UCS
Eber
hard
t et
al.
(199
8b)
This correlates with experimental studies of brittle rock failure that show that stress-induced damage initiates at approximately 40%.
28 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Damage Around an Underground Excavation
In other words, stress-induced failure process begins at stress levels well below the rock’s unconfined compressive strength.
15
29 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Example: Tunnel Spalling & Depth of FailureProblem: A 14-m diameter, 100-m deep tunnel is to
be excavated in a weak but massive sedimentary rock unit with an average compressive strength of 25 MPa. The tunnel will be excavated by a tunnel boring machine. In-situ stress tests revealed that the major principal stress is horizontal and three times higher than the vertical stress. This has raised concerns of potential ground control problems related to stress-induced fracturing and slabbing of the rock.
As such, the designers need to estimate the potential depth of stress-induced slabbing in order to select the proper rock support measures.
30 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Example: Tunnel Spalling & Depth of FailureAssuming a vertical stress of 2.5 MPa (calculated from the overburden), and adopting a horizontal to vertical stress ratio of 3, a maximum tangential stress of 20 MPa in the tunnel roof is calculated.
8.025
20max MPac
Using Martin et al. (1999)’s empirical relationship
5.1a
D f
mmD f 1285.1
This means that, potentially, the slabbing may extend 4 m into the roof.
maD f 4
16
31 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Tunnel Spalling & Depth of Failure
Using Martin et al. (1999)’s empirical
relationship
32 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Unstable Crack Propagation
Stable propagation: controlling the applied load can stop crack growth.
Unstable propagation: relationship between the applied stress and the crack length ceases to exist and other parameters, such as the crack growth velocity, take control of the propagation process.
Under such conditions, crack propagation would be expected to continue even if loading was stopped and held constant.
As crack-induced damage accumulates, the stress level associated with crack initiation remains essentially unchanged; however, the stress level required for rupture reduces dramatically.
Bien
iaws
ki (1
967) Bieniawski (1967) correlated the threshold
for unstable crack growth, also referred to as the point of critical energy release and the crack damage threshold, with the point of reversal in the volumetric stress-strain curve.
17
33 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Stiffness, Energy & Failure
Capacity of the pillar to sustain load = Pmax
A
BPillar still has capacity to support load post-peak along AB
However, the post peak behaviour is also influenced by the surrounding rock stiffness (through which the pillar is being loaded).
The violence and completeness of failure once unstable crack propagation is reached will depend on the relationship between the stiffness of the loaded component and that of the surrounding rock.
34 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Hoek & Brown (1980)
Unstable Crack Propagation – Pillar Loading
Thus, if we have an increase of convergence s beyond Pmax, to accommodate this displacement, the load on the pillar must reduce from PA to PB.
s
D E
FPF
Cs
A
PB
B
PAThe amount of energy, Wpillar, absorbed in the process is given by the area ABED.
1
However, in displacing by s from point A, the mine rock only unloads to F and releases stored strain energy, Wmine, given by the area AFED.
2
In this case, Wmine > Wpillar, and catastophic failure occurs at, or shortly after, peak strength because the energy released by the mine rock during unloading is greater than that which can be absorbed by the pillar.
3
18
35 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Brittle Failure in TunnellingCa
iet
al.(
2004
)
Diederichs (2007)
36 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Grain Size – Spalling or Rockburst
Tonalite(intrusive)
Hornfel(fine-grain
metamorphic)
SPALLING
19
37 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Grain Size – Spalling or Rockburst
Tonalite(intrusive)
Hornfel(fine-grain
metamorphic)
BURST
38 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Influence of Confining Stress
Eberhardt (1998a)
Under low confinement, propagating cracks can more easily open (in the 3direction), leading to the accumulation of brittle fracture damage and crack coalescence. In contrast, the addition of confinement works to suppress crack propagation limiting fracture coalescence and preventing unstable crack growth. Confining stress therefore plays an important role as the brittle failure process will self-stabilize at some distance into the rock mass due to confinement.
Mar
tin
(199
7)
20
39 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Ground Control through Confinement
40 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Lecture ReferencesBieniawski, ZT (1967). Mechanism of brittle rock fracture: Part I - Theory of the fracture process.International Journal of Rock Mechanics and Mining Sciences & Geomechanical Abstracts 4(4): 395-406.
Brace, WF & Bombolakis, EG (1963). A note on brittle crack growth in compression. Journal ofGeophysical Research, 68(12): 3709-3713.
Cai, M, Kaiser, PK, Uno, H, Tasaka, Y & Minami, M (2004). Estimation of rock mass deformationmodulus and strength of jointed hard rock masses using the GSI system. International Journal ofRock Mechanics & Mining Sciences 41(1): 3-19.
Diederichs, MS (2007). Mechanistic interpretation and practical application of damage and spallingprediction criteria for deep tunnelling. Canadian Geotechnical Journal, 44(9): 1082-1116.
Eberhardt, E (2001). Numerical modeling of three-dimensional stress rotation ahead of an advancingtunnel face. International Journal of Rock Mechanics and Mining Sciences: 38(4), 499-518.
Eberhardt, E, Stead, D, Stimpson, B & Lajtai, EZ (1998a). The effect of neighbouring cracks onelliptical crack initiation and propagation in uniaxial and triaxial stress fields. Engineering FractureMechanics 59(2): 103-115.
Eberhardt, E, Stead, D, Stimpson, B & Read, RS (1998b). Identifying crack initiation andpropagation thresholds in brittle rock. Canadian Geotechnical Journal 35(2): 222-233.
Griffith, AA (1920). The phenomena of rupture and flow in solids. Philosophical Transactions of theRoyal Society of London, Series A, Mathematical and Physical Sciences, 221(587): 163-198.
21
41 of 41 Tunnelling Grad Class (2014) Dr. Erik Eberhardt
Lecture ReferencesGriffith, AA (1924). The theory of rupture. In Proceedings of the First International Congress forApplied Mechanics, Delft, pp. 55-63.
Harrison, JP & Hudson, JA (2000). Engineering Rock Mechanics – Part 2: Illustrative WorkedExamples. Elsevier Science: Oxford.
Hoek, E & Brown, ET (1980). Underground Excavations in Rock. Institution of Mining andMetallurgy: London.
Ingraffea, AR (1987). Theory of crack initiation and propagation in rock. In Fracture Mechanics ofRock. Academic Press Inc. Ltd.: London, pp. 71-110.
Lajtai, EZ (1971). A theoretical and experimental evaluation of the Griffith theory of brittlefracture. Tectonophysics, 11: 129-156.
Kaiser, PK, Diederichs, MS, Martin, D, Sharpe, J & Steiner, W (2000). Underground works inhard rock tunnelling and mining. In GeoEng2000, Melbourne. Technomic Publishing Company:Lancaster, pp. 841-926.
Martin, CD (1997). The effect of cohesion loss and stress path on brittle rock strength. CanadianGeotechnical Journal, 34(5): 698-725.
Martin, CD, Kaiser, PK & McCreath, DR (1999). Hoek-Brown parameters for predicting the depthof brittle failure around tunnels. Canadian Geotechnical Journal 36(1): 136-151.
Whyatt, JK, Blake, W & Williams, TJ (1997). Classification of large seismic events at the LuckyFriday Mine. Transactions of the Institution of Mining and Metallurgy, Section A: Mining Industry,106: A148–A162.
Top Related