03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 1
BASIC TRAINING IN HYDRAULICS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 2
TRAINING CONTENTS
• Principle of fluid power and hydraulics
• Applications of hydraulics in various fields.
• Properties of fluids.• Pascal’s law & applications • Signal flow in hydraulic system.• Symbolic representation of
different energy supply elements like pump, filter, motor, pressure regulator, hydraulic power pack, hydraulic accumulator etc.
• Working principle & symbolic representation of different types of direction control valves.
• Basic hydraulic circuits used in different applications
• Practice on work station• Practice on software fluid
sim-hydraulics
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 3
INTRODUCTION
• The controlled movement of parts or a controlled application of force is a common requirement in the industries.
• These operations are performed mainly by using electrical machines or diesel, petrol and steam engines as a prime mover.
Power source
Energy medium
Control system
Prime mover Load
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 4
WHAT IS FLUID POWER?• Fluid power is the engineering science and technology
that deal with the generation, control, and transmission of energy through the use of pressurized fluids.
• Or• Fluid power technology is to convert, transmit, control &
apply fluid energy to perform useful work. Fluid can be either a liquid or gas.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 5
HYDRAULICS
• The study of hydraulics deals with system operated with hydraulic oil media to impart power or to control power.
• Hydraulic power is the power that is transmitted by pressurized oil.
• It may be used to power machines or to control or to regulate machines.
Oil tank / reservoir
Power source (Pump)
Pressurized oil
Control valve Actuator
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 6
BASIC PRINCIPLES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 7
HISTORICAL REVIEW
• Actual advancement of ‘Oil Hydraulics’ started from the end of 17th Century. In 1648, a French Physicist, Pascal, discovered a fundamental law underlying the whole science of Hydraulics.
• It’s a two-part statement as given here:– Pressure at any point in a static fluid is the same in every
direction,– Pressure exerted on a confined fluid is transmitted equally
in all directions, acting with equal force on equal areas.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 8
FUNDAMENTAL PHYSICAL PRINCIPLES OF HYDRAULICS• Every body exerts a
specific pressure “p” on its base.
• The value of this pressure is dependent on the force due to weight “F” of the body and on the size of the area “A” on which the force due to weight acts.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 9
FUNDAMENTAL PHYSICAL PRINCIPLES OF HYDRAULICS• Two bodies with different bases
(A1 and A2 ). • Where the bodies have identical
mass, the same force due to weight (F) acts on the base.
• However, the pressure is different owing to the different sizes of base.
• Where the force due to weight is identical, a higher pressure is produced in the case of a small base than in the case of a larger base.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 10
FUNDAMENTAL PHYSICAL PRINCIPLES OF HYDRAULICS• This is expressed by the following formula:• P=F/A • Unit: 1Pa = 1N/m^2• 1 bar = 100000N/m^2 = 10^5 Pa• P = Pressure, Pascale [Pa]• F = Force, Newton [N]• A = Area, Square meter [m^2]
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 11
PRESSURE TRANSMISSION• If a force F1 acts via an area A1
on an enclosed liquid, a pressure “p” is produced which extends throughout the whole of the liquid (Pascal’s Law).
• The same pressure applies at every point of the closed system .
• The same pressure acts on the surfaces A2, A3 as on A1.
• This is expressed by means of the following formula:
• p = F/A
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 12
POWER TRANSMISSION• The same pressure applies at
every point in a closed system. • For this reason, the shape of
the container has no significance.
• Where a container is formed as shown in the diagram, it is possible to transmit forces.
• The fluid pressure can be described by means of the following equations:
• p1 = F1/A1 & p2 = F2/A2
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 13
PASCAL'S LAW & ITS APPLICATIONS• Now assume a force of 50N is applied downward on p1,• The Pressure created by P1=Force/Area • =50N/10cm2 = 5N/cm2 • A/c to Pascal's law, pressure acts equally in all direction.• So, the pressure acting on p2 is also 5N/cm2 . As the p2 has the
area of 100cm2 .• So, Force available on p2 =Pressure X Area• = 5N/cm2 X 100cm2 =500N• “The force applied to piston 1 is multiplied 10 times, this
advantage is utilised in fluid power system !!!”
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 14
TYPES OF FLOW
• Two types of fluid flows• Laminar flow & turbulent flow
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 15
HYDRAULIC SYSTEMS.• The hydraulic systems consists a number of parts for its proper functioning. • These include storage tank, filter, hydraulic pump, pressure regulator,
control valve, hydraulic cylinder, piston and leak proof fluid flow pipelines.• It consists of:
– Cylinder– Storage tank– Filter– Electric pump– Pressure regulator– Control valve– Leak proof closed loop piping.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 16
SCHEMATIC OF HYDRAULIC SYSTEM
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 17
HYDRAULIC SYSTEMS...• The storage/fluid tank is a reservoir for the liquid used
as a transmission media. • The liquid used is generally high density incompressible
oil. It is filtered to remove dust or any other unwanted particles and then pumped by the hydraulic pump.
• The capacity of pump depends on the hydraulic system design. These pumps generally deliver constant volume in each revolution of the pump shaft. Therefore, the fluid pressure can increase indefinitely at the dead end of the piston until the system fails.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 18
HYDRAULIC SYSTEMS....• The pressure regulator is used to avoid such
circumstances which redirect the excess fluid back to the storage tank.
• The movement of piston is controlled by changing liquid flow from port A and port B.
• The cylinder movement is controlled by using control valve which directs the fluid flow.
• The leak proof piping is also important due to safety, environmental hazards and economical aspects.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 19
TYPES OF HYDRAULICS• The place held by hydraulics in (modern) automation
technology illustrates the wide range of applications for which it can be used.
• A basic distinction is made between:– Stationary hydraulics– Mobile hydraulics
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 20
STATIONARY HYDRAULICS• Stationary hydraulics is fixed at one station where all the
activities are carried out at the same station. Stationary hydraulics is used in machine tool applications.
• The following application areas are important for stationary hydraulics:
– Production and assembly machines of all types – Transfer lines– Lifting and conveying devices – Presses – Injection moulding machines– Rolling lines– Lifts
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 21
MOBILE HYDRAULIC
• Mobile hydraulic systems move on wheels or tracks, for example, unlike stationary hydraulic systems which remain firmly fixed in one position.
• A characteristic feature of mobile hydraulics is that the valves are frequently manually operated.
• Typical application fields for mobile hydraulics include:
– Construction machinery – Excavators, elevating platforms – Lifting and conveying devices – Agricultural machinery
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 22
PUMPS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 23
HYDRAULIC PUMP
• A pump is the heart of the hydraulic system, convert mechanical energy into hydraulic energy.
• Main purpose of the pump is to create the flow of oil through the system & thus assist transfer of power & motion.
• The combined pumping and driving motor unit is known as hydraulic pump.
• The hydraulic pump takes hydraulic fluid (mostly some oil) from the storage tank and delivers it to the rest of the hydraulic circuit.
• In general, the speed of pump is constant and the pump delivers an equal volume of oil in each revolution.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 24
HYDRAULIC PUMP
• The hydraulic pumps are characterized by its flow rate capacity, power consumption, drive speed, pressure delivered at the outlet and efficiency of the pump.
• The pumps are not 100% efficient. • The efficiency of a pump can be specified by two ways:
– One is the volumetric efficiency which is the ratio of actual volume of fluid delivered to the maximum theoretical volume possible.
– Second is power efficiency which is the ratio of output hydraulic power to the input mechanical/electrical power.
• The typical efficiency of pumps varies from 90-98%.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 25
HYDRAULIC PUMP
• The hydraulic pumps can be of two types: – centrifugal pump – reciprocating pump
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 26
CENTRIFUGAL PUMP
• Centrifugal pump uses rotational kinetic energy to deliver the fluid.
• The rotational energy typically comes from an engine or electric motor.
• The fluid enters the pump impeller along or near to the rotating axis, accelerates in the propeller and flung out to the periphery by centrifugal force as shown in figure.
• In centrifugal pump the delivery is not constant and varies according to the outlet pressure.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 27
CENTRIFUGAL PUMP
• These pumps are not suitable for high pressure applications and are generally used for low-pressure and high-volume flow applications.
• The maximum pressure capacity is limited to 20-30 bars.
• Most of the centrifugal pumps are not self-priming and the pump casing needs to be filled with liquid before the pump is started.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 28
RECIPROCATING OR POSITIVE DISPLACEMENT PUMP
• The reciprocating pump is a positive plunger pump. It is also known as positive-displacement pump or piston pump.
• It is often used where relatively small quantity is to be handled and the delivery pressure is quite large. The construction of these pumps is similar to the four stroke engine as shown in figure.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 29
RECIPROCATING OR POSITIVE DISPLACEMENT PUMP
• The crank is driven by some external rotating motor. • The piston of pump reciprocates due to crank rotation. The piston
moves down in one half of crank rotation, the inlet valve opens and fluid enters into the cylinder.
• In second half crank rotation the piston moves up, the outlet valve opens and the fluid moves out from the outlet.
• At a time, only one valve is opened and another is closed so there is no fluid leakage.
• Depending on the area of cylinder the pump delivers constant volume of fluid in each cycle independent to the pressure at the output port.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 30
CLASSIFICATION OF HYDRAULIC PUMPS• These are mainly classified into two categories:
Pump
Hydrostatic(Positive displacement)
Hydrodynamic(Non-Positive displacement)
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 31
POSITIVE DISPLACEMENT PUMPS• This pump ejects fixed quantity of fluid per revolution of
the pump shaft. The pump outlet flow is constant & is not depended on the system pressure. So they are suited for fluid power system.
• Positive displacement pumps must be protected against overload. The reason is that, it continues to eject fluid (even though it has no place to go) causing an extremely rapid build up of pressure.
• Example: Gear pump, Vane pump, piston pump.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 32
ADVANTAGES OF POSITIVE DISPLACEMENT PUMPS• PD pumps are widely used in hydraulic system• They generate high pressure• They are relatively small & enjoy very high power to
weight ratio.• They have greater flexibility of performance under
varying speed pressure requirement.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 33
CONSTRUCTION & PRINCIPAL OF PD PUMPS..• Reciprocating pump are generally cylinders with
operating as a pump. They are available in various size, shape & driving mechanisms. Due to high pressure they are used for specialized applications. A pump using this principle is known as piston pump.
• Rotary pump are most common in oil hydraulics system when low to medium pressure is the prime consideration.
– The 3 prime types are: – 1) Gear, 2) Vane, 3) Screw
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 34
GEAR PUMPS
• Gear pump is a robust and simple positive displacement pump. It has two meshed gears revolving about their respective axes.
• The rigid design of the gears and houses allow for very high pressures and the ability to pump highly viscous fluids.
• They are suitable for a wide range of fluids and offer self-priming performance.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 35
GEAR PUMPS
• Based upon the design, the gear pumps are classified as:
– External gear pumps– Lobe pumps – Internal gear pumps– Gerotor pumps
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 36
EXTERNAL GEAR PUMP• External gear pumps have two mating gear in a closed
fitted housing. One of the gear is connected to a drive shaft connected to the prime mover. The 2nd one, the follower gear is driven as it meshes with the driver gear.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 37
HOW EXTERNAL GEAR PUMP WORK !
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 38
GENERALLY GEAR PUMPS ARE USED TO PUMP• Petrochemicals: Diesel oil, crude oil, lube oil etc.• Chemicals: Sodium silicate, acids, plastics, mixed
chemicals etc.• Paint and ink• Resins and adhesives• Pulp and paper: acid, soap, lye, black liquor, lime,
sludge etc.• Food: Chocolate, cacao butter, fillers, sugar, vegetable
fats and oils, animal food etc.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 39
PISTON PUMPS
• Piston pumps are meant for the high-pressure applications. These pumps have high efficiency and simple design and needs lower maintenance.
• These pumps convert the rotary motion of the input shaft to the reciprocating motion of the piston. These pumps work similar to the four stroke engines.
• They work on the principle that a reciprocating piston draws fluid inside the cylinder when the piston retracts in a cylinder bore and discharge the fluid when it extends.
• These pumps are positive displacement pump and can be used for both liquids and gases.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 40
PISTON PUMPS TYPES
• Piston pumps are basically of two types:– Axial piston pumps
• Bent axis piston pumps• Swash plate axial piston pump
– Radial piston pumps
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 41
AXIAL PISTON PUMP
• Axial piston pumps are positive displacement pumps which converts rotary motion of the input shaft into an axial reciprocating motion of the pistons.
• These pumps have a number of pistons (usually an odd number) in a circular array within a housing which is commonly referred to as a cylinder block, rotor or barrel.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 42
COMBINATION PUMP
• Two basic requirements for load lifting or load applying by a hydraulic ram.
• First, there is a need of large volume of fluid at a low pressure when the cylinder extends or retracts. The low pressure is required to overcome the frictional resistance.
• The second requirement is that a high pressure is needed, when the load is gripped.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 43
COMBINATION PUMP
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 44
COMBINATION PUMP
• In this system two separate pumps are driven by a common electrical motor.
• Pump P1 is a high pressure low volume pump and pump P2 is a high volume low pressure pump.
• The hydraulic system is associated with relief valves RV1 and RV2 and a one-way check valve CV1.
• This kind of arrangement allows the fluid flow from left to right.• This kind of arrangement saves energy as the large volume of
fluid from pump P2 is returned to the tank at a very low pressure, and only a small volume of fluid from pump P1 is returned at a high pressure.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 45
HYDRAULIC FLUID &
PROPERTIES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 46
JOB PERFORM BY THE HYDRAULIC OIL• They have the following primary tasks:
– Power transmission (pressure and motion transmission)– Signal transmission for control
• Secondary tasks:– Lubrication of rotating and translating components to avoid
friction and wear– Heat transport, away from the location of heat generation,
usually into the reservoir– Transport of particles to the filter– Protection of surfaces from chemical attack, especially corrosion
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 47
HYDRAULIC FLUIDS REQUIREMENTS• Functional
– Good lubrication characteristics– Viscosity should not depend strongly on temperature and
pressure– Good heat conductivity– Low heat expansion coefficient– Large elasticity modulus
• Economic– Low price– Slow aging and thermal and chemical stability long life
cycle
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 48
HYDRAULIC FLUIDS REQUIREMENTS• Safety
– High flash point or in certain cases not inflammable at all– Chemically neutral (not aggressive at all against all
materials it touches)– Low air dissolving capability, not inclined to foam
formation• Environmental friendliness
– No environmental harm– No toxic effect
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 49
PROPERTIES OF HYDRAULIC FLUID.• Good Lubricity• Stable Viscosity
Characteristics• Good Heat Dissipation• Flash Point
• Low Foaming Tendency• Fire Resistant• Prevent Rust Formation• Non-toxic, Easy to
handle & Available
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 50
GOOD LUBRICITY
• The component in a hydraulic system contain many surface which are in close contact and which move in relation to each other. The hydraulic fluid must separate and lubricate such surfaces. Protection against wear is a principal reason for selecting a fluid having good lubrication characteristics as a hydraulic medium.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 51
GOOD HEAT DISSIPATION• An important requirement of the fluid is to carry heat
away from the working parts. • Pressure drops, mechanical friction, fluid friction,
leakages, all generate heat. • The fluid must carry the generated heat away and
readily dissipate it to the atmosphere or coolers. • Therefore high thermal conductivity and high specific
heat values are desirable in the fluid chosen.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 52
FLASH POINT
• The flash point of a hydraulic oil is defined as the temperature at which flashes will be generated when oil is brought into contact with any heated matter, e.g., a heat stick.
• Low flash point oils are not use as Hydraulic Oil.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 53
LOW FOAMING TENDENCY• Foam results from air or other gases becoming entrained in
the hydraulic fluid. Air enters a hydraulic system through the reservoir or through air leaks within the system.
• A hydraulic fluid under high pressure can contain a large volume of dissolved or dispersed air bubbles. When this fluid is depressurized, the air bubbles expand and produce foam. Because of its compressibility and poor lubricating properties, foam can seriously affect the operation and lubrication of machinery.
• Proper foam inhibitors modify the surface tension on air bubbles so they more easily break up.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 54
FIRE RESISTANT
• Fire resistance is one of the properties that is optional in a good usable hydraulic fluid.
• The commonly used hydraulic liquid are petroleum derivative, and consequently they burn vigorously once they pass the point.
• For critical application, artificial or synthetic hydraulic fluid are used which have high fire resistances. Various grades of fluids with high water content are also available now a days for oil hydraulic system.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 55
STABLE VISCOSITY CHARACTERISTICS• Viscosity is a measure of a hydraulic fluid's resistance to flow.
It is a hydraulic fluid's most important characteristic and has a significant impact on the operation of the system.
• When a hydraulic oil is too thin (low viscosity), it does not seal sufficiently. This leads to leakage and wear of parts. When a hydraulic oil is too thick (high viscosity), the fluid will be more difficult to pump through the system and may reduce operating efficiency.
• All hydraulic fluids must be able to retain optimum viscosity during operation in cold or hot temperatures, in order to consistently and effectively transmit power
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 56
PREVENT RUST FORMATION• In many systems, water can enter as condensation or
contamination, and mix with the hydraulic oil. Water can cause rusting of hydraulic components.
• In addition, water can react with some additives to form chemical species which can be aggressive to yellow metals.
• Hydraulic oil formulations contain rust and corrosion inhibitors which prevent the interaction of water or other chemical species from attacking metal surfaces.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 57
NON-TOXIC, EASY TO HANDLE & AVAILABLE• These characteristics refer to the interaction of the fluid
with people who repair, handle, use or pay for hydraulic system fluid.
• Obviously, it is desirable that the fluid be as simple to handle and as available and cheap as possible.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 58
FLUID POWER SYSTEMS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 59
HYDRAULIC POWER PACK
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 60
POWER PACK
• The hydraulic power unit (power supply unit) provides the energy required for the hydraulic installation. Its most important components are
– The reservoir (tank) , – Drive (electric motor), – Hydraulic pump, – Pressure relief valve ,– Filter and cooler.
• The hydraulic power unit may also act as a carrier for other devices (gauges, directional control valves).
P T
Ts
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 61
HYDRAULIC SYMBOLS
W H Y W E N E E D H Y D R AU L I C S Y M B O L S ?
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 62
SCHEMATIC REPRESENTATION
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 63
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 64
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 65
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 66
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 67
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 68
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 69
M
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 70
M
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 71
Pump
Tank
DCV
Actuator
Filter
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 72
GRAPHICAL REPRESENTATION OF HYDRAULIC AND PNEUMATIC ELEMENTS• The hydraulic and pneumatic elements such as cylinders and valves are
connected • through pipelines to form a hydraulic or a pneumatic circuit. It is difficult to represent
the • complex functioning of these elements using sketches. Therefore graphical symbols are • used to indicate these elements. The symbols only specify the function of the
element • without indicating the design of the element. Symbols also indicate the actuation
method, • direction of flow of air and designation of the ports. Symbols are described in
various • documents like DIN24300, BS2917, ISO1219 and the new ISO5599, CETOP RP3 and • the original American JIC and ANSI symbols.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 73
GRAPHICAL REPRESENTATION OF HYDRAULIC AND PNEUMATIC ELEMENTS
• The symbol used to represent an individual element display the following characteristics:
– Function – Actuation and return actuation methods – Number of connections – Number of switching positions – General operating principle – Simplified representation of the flow path
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 74
GRAPHICAL REPRESENTATION OF HYDRAULIC AND PNEUMATIC ELEMENTS
• The symbol does not represent the following characteristics:
– Size or dimensions of the component – Particular manufacturer, methods of construction or costs – Operation of the ports – Any physical details of the elements – Any unions or connections other than junctions
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 75
SYMBOLS FOR PORTS
• Earlier the ports were designated with letter system. Now as per ISO5599 the ports are designated based on number system.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 76
SYMBOLS FOR PORTS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 77
GRAPHICAL SYMBOLS OF HYDRAULIC ELEMENTS AND EQUIPMENT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 78
GRAPHICAL SYMBOLS OF HYDRAULIC ELEMENTS AND EQUIPMENT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 79
GRAPHICAL SYMBOLS OF HYDRAULIC ELEMENTS AND EQUIPMENT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 80
CIRCUIT SYMBOLS FOR
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 81
DIRECTIONAL CONTROL VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 82
DIRECTIONAL CONTROL VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 83
4/3WAY DIRECTIONAL CONTROL VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 84
CIRCUIT SYMBOLS FOR MANUAL OPERATION
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 85
CIRCUIT SYMBOLS FOR MANUAL OPERATION
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 86
CIRCUIT SYMBOLS FOR FLOW CONTROL VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 87
CIRCUIT SYMBOL FOR PRESSURE VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 88
CIRCUIT SYMBOLS FOR NON-RETURN VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 89
HYDRAULIC ACTUATORS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 90
HYDRAULIC ACTUATORS• The fluid discharged by the pump is directed to the
‘hydraulic actuator’. The actuator convert the pressure energy of the fluid into mechanical energy. There are 3 basic type of hydraulic actuator.
• The actuators convert the fluid pressure to a suitable linear or rotary motion.
• Linear motion – Hydraulic cylinder• Rotary motion – Hydro motor• Rotary motion – Semi-rotary actuator
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 91
HYDRAULIC CYLINDERS• A hydraulic cylinder is a device, which converts
fluid power into linear mechanical force and motion. It usually consists of a movable element, a piston and a piston rod operating within a cylindrical bore.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 92
PARTS OF A HYDRAULIC CYLINDER• A hydraulic
cylinder consists of the following parts
• Cylinder barrel• Piston• Piston rod• Bush• Cylinder head
and cap
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 93
TYPE OF HYDRAULIC CYLINDER
Hydraulic cylinder
Single acting
cylindersDouble acting
cylinders
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 94
SINGLE ACTING CYLINDER • In the case of a single acting cylinder, only the piston
side is pressurized with hydraulic fluid. The cylinder can thus carry out work only in one direction. The fluid which flows into the piston chamber causes a pressure to build up the surface of the piston. The piston travels into its forward end position. The return stroke is effected by a spring, the dead weight of the piston rod or an external load
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 95
SINGLE ACTING CYLINDER.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 96
PLUNGER TYPE SINGLE ACTING CYLINDER• In the case of plunger
cylinders, the piston and rod form a single component. Due to the design of the cylinder, the return stroke can only be effected by external forces. The cylinders can therefore generally be installed only vertically.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 97
PLUNGER TYPE SINGLE ACTING CYLINDER
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 98
PLUNGER TYPE SINGLE ACTING CYLINDER
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 99
APPLICATION OF SINGLE ACTING CYLINDER
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 100
DOUBLE ACTING CYLINDERS• In the case of double acting cylinders, both piston
surfaces can be pressurized. A working movement can thus be performed in both directions.
• With double acting cylinders with a single-sided piston rod, different forces and speeds are obtained on the advance and return strokes due to the difference in area between the piston surface and annular piston surface.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 101
DOUBLE ACTING CYLINDERS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 102
APPLICATION OF DOUBLE ACTING CYLINDERS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 103
DOUBLE ACTING CYLINDER WITH END POSITION CUSHIONING • Cylinder with end position cushioning are used to brake
high stroke speeds smoothly and prevent hard impacts at the end of the stroke. Shortly before the end position is reached, the cross- section for the outflow of fluid is reduced by the built-in cushioning pistons and then finally closed. The hydraulic fluid is then forced to escape through a flow control valve.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 104
CUSHIONING CYLINDER
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 105
END POSITION CUSHIONING • The piston is a short distance
before its end position; the hydraulic fluid on the piston-rod side must escape via the adjustable flow control valve above the piston rod
• This type of end position cushioning is used for stroke speed between 6 m/min and 20 m/min. At higher speed, additional cushioning or braking devices must be used
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 106
END POSITION CUSHIONING • The piston rod is on its
return stroke; in this flow direction, the non-return valve below the piston rod is opened, thus by-passing the flow control valve. The piston rod retracts at maximum speed.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 107
DOUBLE-ACTING CYLINDER WITH CUSHIONING
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 108
TELESCOPIC CYLINDER• Often cylinder & rod length does not fit in the machine. In
that case the piston rod is also used as a piston barrel and a second piston rod is used.
• These kinds of cylinders are called telescopic cylinders. If we call a normal rod cylinder single stage, telescopic cylinders are multi-stage units of two, three, four, five or more stages.
• In general telescopic cylinders are much more expensive than normal cylinders. Most telescopic cylinders are single acting (push). Double acting telescopic cylinders must be specially designed and manufactured.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 109
TELESCOPIC CYLINDER
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 110
HYDRAULIC MOTORS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 111
HYDRAULIC MOTORS
• In hydraulic system generally hydraulic motor provide rotational movement. A hydraulic motor transform hydraulic energy into mechanical energy which is applied to a resistance object by means of a shaft connected with the motor.
• Hydraulic motor closely resemble hydraulic pumps in construction & size. The only difference is that instead of pushing the fluid as the pump does, in hydraulic motor the rotating elements(i.e. vanes, gear, piston, etc.) are pushed by the oil pressure to enable the motor shaft to rotate & thus develop the necessary turning torque & continuous rotational motion.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 112
CONSTRUCTION OF EXTERNAL GEAR MOTOR
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 113
HYDRAULIC MOTOR USED IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 114
SEMI ROTARY ACTUATOR • The limited angle rotary
actuator is applied when the shaft has to rotate over a limited angle. The animation shows how this simple actuator works: in this case the shaft can rotate over an angle of about 270 degrees. This type of actuator is, among others, used as a rotator actuator on (small) cranes and excavators
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 115
HYDRAULIC VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 116
HYDRAULIC VALVES
• The pressure energy is fed to the actuator through a number of control block called valves.
• Various type of valve are used in hydraulic system to control or regulate the flow medium. Basically valves are expected to control:
– Direction– Pressure– Flow– Other special functions.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 117
DIRECTIONAL CONTROL VALVES• These valves control the direction of flow of the
hydraulic fluid and, thus, the direction of motion and the positioning of the working components. Directional control valves may be actuated manually, mechanically, electrically, pneumatically or hydraulically. They convert and amplify signals(manual, electric or pneumatic) forming an interface between the power control section and the signal control section.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 118
DIRECTIONAL CONTROL VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 119
SYMBOL DESIGN OF VALVES.• Method of designation of valve• The basic symbol for control valve is a square.• Two or more squares are used.• Each square representing the switching position
provided by the valve.• 1. Two position valve.
• 2.Three position valve.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 120
SYMBOL DESIGN OF VALVES..• Lines in the boxes are used to show flow path with
arrow indicating direction of flow.
• The shut off position is indicated by the line drawn at right angle to the horizontal line inside the rectangle.
FLOW
SHUT OFF / NO FLOW
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 121
PIPE CONNECTIONS
• The pipe connections i.e. inlet and outlet ports to the valve are indicated by lines drawn on outside of the box and right angle to the horizontal line .
• The first position from left indicates the rest, initial or neutral position when the valve is not actuated.
• The second position or square from left indicates actuated position.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 122
PIPE CONNECTIONS
• Single position (initial)
• Two position valve
• Three position valve
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 123
COMMONLY USED DIRECTION CONTROL VALVES
• Direction control valve is used to control or to change the direction or to start or stop the fluid flow only on the receipt of any signal which may be mechanical, electrical or a fluid pressure pilot signal.
• Direction control valves are described by number of ports and number of positions
– n / n way valve– ( n = 1, 2, 3,……)
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 124
WAY/POSITION
• Way Valve Ports Positions• 2/2 2 (1 input , 1 output) 2• 3/2 3 (1 input, 1 output, 1 tank) 2• 4/2 4 (1 input, 2 output, 1 tank) 2• 4/3 4 (1 input, 2 output, 1 tank) 3
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 125
(2/2 ) ON/OFF VALVE
• The most basic direction control valve is the simple on/off valve. A simple version is shown symbolically below.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 126
(2/2 ) ON/OFF VALVE
• 2/2 way valve normally closed• Not actuated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 127
(2/2 ) ON/OFF VALVE
• 2/2 way valve normally closed• Actuated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 128
(2/2 ) ON/OFF VALVE USED IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 129
(3/2 ) DIRECTION CONTROL VALVE• The three way version of the above valve which allows
the outlet port to be connected to either the pump or the reservoir is shown below
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 130
(3/2 ) DIRECTION CONTROL VALVE• Normally closed• Not activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 131
(3/2 ) DIRECTION CONTROL VALVE• Normally close • Activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 132
(3/2 ) DIRECTION CONTROL VALVE IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 133
(4/2 ) DIRECTION CONTROL VALVE• Normally close • Not Activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 134
(4/2 ) DIRECTION CONTROL VALVE• Normally close • Activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 135
(4/2 ) DIRECTION CONTROL VALVE IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 136
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 137
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 138
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 139
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 140
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 141
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 142
(4/3 ) DIRECTION CONTROL VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 143
(4/3 ) DIRECTION CONTROL VALVE• 4/3 way mid-position recirculation / tandem mid-position• Middle position is activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 144
(4/3 ) DIRECTION CONTROL VALVE• 4/3 way mid-position recirculation / tandem
mid-position• Position 1 is activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 145
(4/3 ) DIRECTION CONTROL VALVE• 4/3 way mid-position recirculation / tandem mid-position• Position 3 is activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 146
(4/3 ) DIRECTION CONTROL VALVE• 4/3 way mid position cutoff / all ports blocked mid
position• Position 2 is activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 147
(4/3 ) DIRECTION CONTROL VALVE• 4/3 way mid position cutoff / all ports blocked mid
position• Position 1 is activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 148
(4/3 ) DIRECTION CONTROL VALVE• 4/3 way mid position cutoff / all ports blocked mid
position• Position 3 is activated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 149
(4/3) DIRECTION CONTROL VALVE IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 150
(4/3) DIRECTION CONTROL VALVE USED IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 151
(4/3) DIRECTION CONTROL VALVE USED IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 152
NON-RETURN /CHECK VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 153
NON-RETURN /CHECK VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 154
NON-RETURN /CHECK VALVE (DIRECTION CONTROL VALVE)
• Check Valves are simply valves which provide reasonably unrestricted flow in one direction and stop the flow in the other direction. A light spring is generally used to retain the valve to a closed position on near zero flow.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 155
NON-RETURN /CHECK VALVE (DIRECTION CONTROL VALVE)
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 156
NON-RETURN /CHECK VALVESUSED IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 157
PILOT OPERATED CHECK VALVES• As opposed to the simple non
return valve, pilot operated check valve may also be operated in the direction of close.
• These valves are used, for example:
– To isolated work circuits under pressure
– To prevent the load from dropping, if a line should break
– To prevent creep movements hydraulically loaded actuators
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 158
PILOT OPERATED CHECK VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 159
PILOT OPERATED CHECK VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 160
PRE-FILL VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 161
PRE-FILL VALVE
• Pre-fill valve are large size hydraulic pilot operated check valve. They are used mainly to pre fill large cylinder volumes and to isolate the main working circuit under pressure.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 162
FLOW RATE
• Flow rate is the term used to describe the volume of liquid flowing through a pipe in a specific period of time. For example, approximately one minute is required to fill a10 litre bucket from a tap. Thus, the flow rate amounts to 10 l/min.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 163
FLOW RATE
In hydraulics, the flow rate is designated as Q. The following equation applies:
Q =Flow rateV = Volume t = time
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 164
FLOW CONTROL VALVES • The speed of the actuators needs to be altered as per
operational requirement. For this purpose hydraulic systems use flow control valves.
• These interact with pressure valves to affect the flow rate. They make it possible to control or regulate the speed of motion of the power components. Where the flow rate is constant, division of flow must take place. This is generally effected through the interaction of the flow control valve with a pressure valve.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 165
FLOW CONTROL VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 166
FLOW CONTROL VALVE• The main classification of the flow control valve are:
Flow control valve
Non – pressure compensated
Pressurecompensated.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 167
NON-PRESSURE COMPENSATED FLOW CONTROL VALVE
• The simplest type of flow control valve is a needle valve. The needle valve has a pointed stream that can be adjusted manually to control the rate of flow through the valve.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 168
NON-PRESSURE COMPENSATED FLOW CONTROL VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 169
NON-PRESSURE COMPENSATED FLOW CONTROL VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 170
NON-PRESSURE COMPENSATED UNIDIRECTIONAL FLOW CONTROL VALVE
• In most fluid power application needle valve with integrated check valve is used to control the flow rate. This enable a regulated flow in one direction with free flow in the reverse direction.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 171
NON-PRESSURE COMPENSATED UNIDIRECTIONAL FLOW CONTROL VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 172
LOCATION OF FLOW CONTROL VALVES• The location of flow control valves with respect to other
component & the work is quit important because it has an effect on the characteristics of the circuit performance.
• There are 2 basic type of location of a flow control valve in any hydraulic system.
– Meter – in circuit– Meter – out circuit– Bleed off circuit
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 173
METER – IN CIRCUIT
• In this type of circuit, the valve is located in the pressure line leading to the work cylinder.
• The flow entering into the work cylinder is first controlled through the valve.
• Meter – in circuit are generally used when the load characteristics are constant & positive. For free reverse flow, generally a check valve is provided parallel to the flow control valve.
• For example: A hydraulic table feed on a surface grinder would require controlled rate of travel.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 174
METER – OUT CIRCUIT• In this type of circuits, the flow control valve is installed
on the return side of the cylinder so that it controls the speed of the working cylinder by monitoring the discharge flow.
• The meter – out circuit is commonly used in machine tools that require precise control of fluid on discharge from the exhaust side of the cylinder.
• The machine tools like mills and drills often required large restraining force to prevent excessive pull on the cylinders.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 175
PRESSURE CONTROL
VALVESW H Y W E N E E D P R E SS U R E C O N T R O L
VA LV E S ?
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 176
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 177
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 178
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 179
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 180
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 181
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 182
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 183
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 184
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 185
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 186
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 187
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 188
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 189
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 190
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 191
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 192
PRESSURE CONTROL VALVES• Oil energy does the work due to pressure in the
oil system. In a mechanical or hydraulic system there may be a need to increase or decrease the oil pressure depending on the specific requirement. Hence a group of valves called pressure control valve have been designed.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 193
PRESSURE CONTROL VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 194
PRESSURE RELIEF VALVES• Relief valves are generally spring loaded valves which
include a plug over a discharge port which is lifted against an spring force if the system pressure exceeds a certain value. This opens the flow to the discharge port relieving the pressure.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 195
PRESSURE RELIEF VALVES
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 196
PRESSURE RELIEF VALVES (INTERNAL PILOT OPERATED VERSION )• The pilot operated version enables more accurate
control of the setting and a lower relief setting can be accommodated
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 197
PRESSURE RELIEF VALVES (INTERNAL PILOT OPERATED VERSION )
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 198
PRESSURE RELIEF VALVES (EXTERNALLY CONTROLLED/REMOTE PILOT)
The valve opens when pressure at X port is more than spring force.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 199
PRESSURE RELIEF VALVES USED IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 200
PRESSURE RELIEF VALVES USED IN FESTO TRAINING KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 201
APPLICATION OF PRESSURE RELIEF VALVE• It can be used • To relive excessive pressure / to protect pump / other
parts• To limit the system pressure• As a back pressure valve / counterbalancing valve• As a sequence valve
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 202
PRESSURE REDUCING VALVE• This type of valve is used to maintain reduced pressure in specified
location of a hydraulic system. Normally it is an open valve. • A pressure reducing valve is one which used a spring loaded spool
to control the downstream pressure.• If the downstream pressure is below the value pressure, fluid will
flow freely from the inlet to the out let.• When the outlet pressure increases the valve setting , the spool
moves to partially block the outlet port.• If the valve is closed completely by the spool, it could cause the
downstream pressure to buildup above the valve setting. To avoid this, a drain line is provided to drain the fluid to the tank.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 203
PRESSURE REDUCING VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 204
PRESSURE REDUCING VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 205
APPLICATION OF PRESSURE REDUCING VALVE• In oil driven spot welding guns, the control of the
pressure is important for good welding. In that hydraulic system both welding gun and the clamp are powered by the same pump/power pack.
• A pressure reducing valve which is placed in between the welding gun and main pressure, which will regulate the pressure on the spot welding gun.
• The clamp pressure is determined by the pump relief valve setting.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 206
3 WAY PRESSURE REDUCING & RELIEF VALVE • This valve is combination of 2 way pressure regulator &
PRV
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 207
3 WAY PRESSURE REDUCING & RELIEF VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 208
3 WAY PRESSURE REDUCING & RELIEF VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 209
SHUTOFF VALVE
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 210
ACCUMULATORS
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 211
ACCUMULATOR
• Hydraulic accumulator is an accessory of a hydraulic system
• A hydraulic accumulator is a pressure storage reservoir in which a non-compressible hydraulic fluid is held under pressure by an external source.
• The external source can be a spring, a raised weight, or a compressed gas. An accumulator enables a hydraulic system to cope with extremes of demand using a less powerful pump, to respond more quickly to a temporary demand, and to smooth out pulsations. It is a type of energy storage device.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 212
TYPES OF HYDRAULIC ACCUMULATOR• The function of hydraulic accumulator is to store
pressurized oil.• Types:
– Weighted accumulator– Spring loaded accumulator– Gas-charged accumulator
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 213
WEIGHT LOADED TYPE ACCUMULATOR• This is the oldest type of accumulator. This consist of a
vertical, heavy steel cylinder which incorporates a piston with packing to prevent leakage.
• A dead weight is attached to the top of the piston.• The force of gravity of the dead weight provides the
potential energy in the accumulator.• The main disadvantages of this of accumulator is its
large size and heavy weight makes it unsuitable for mobile equipment.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 214
WEIGHT LOADED TYPE ACCUMULATOR
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 215
SPRING LOADED ACCUMULATOR• A spring loaded
accumulator is similar to the weight loaded type, except that the piston is preloaded with a spring.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 216
BLADDER TYPE
• The three types of gas-charged accumulators are bladder, piston and diaphragm.
• The most popular of these is the bladder type. Bladder accumulators feature fast response (less than 25 milliseconds), a maximum gas compression ratio of around 4:1 and a maximum flow rate of 15 liters (4 gallons) per second.
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 217
ACCUMULATOR USED IN FESTO KIT
03/05/2023 Sanjay Humania [M.Tech- Mechatronics] 218
THANK YOU !
Top Related