For further information, contact: ArcelorMittal South Africa, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 1 of 8 File reference: A1.3 Price Lists reference 110 and 111
General description Plate mill products are produced from continuously cast slabs on a 4-high reversing mill in thicknesses from 5mm to 100mm depending on the material specification. Widths range from 1200mm to 3200mm and lengths from 4,0m to 13,0m. Due to furnace dimensions restrictions, normalised and quenched & tempered plates are available in lengths up to 13,0m only. A maximum plate mass of approximately 10 tons can be supplied depending on plate thickness and specification.
Available Dimensions Dimensions available are subject to the following conditions:
1. Minimum length: lengths shorter than 4,0m for as-rolled and 6,0m for normalised material are available on enquiry only.
2. Maximum Length: lengths longer than 13,0m are available on enquiry only. 3. Lengths can be supplied in increments of 10mm. 4. Widths can be supplied in increments of 5mm. 5. Thicknesses can be supplied in increments of 0,5mm. Smaller increments are available on
enquiry. 6. Widths in the thinner gauges are restricted due to mill force constraints. 7. Maximum lengths in the thicker gauges are restricted due to slab mass constraints. 8. Wearplate > 8 mm to 20 mm thickness supplied sides uncut (cut-to length only). 9. For maximum plate dimensions, refer to Tables 1 to 6. 10. The maximum plate lengths for thicknesses between two columns can be determined by linear
interpolation. 11. Due to capacity constraints not all qualities are available to a maximum mass of 10 tons. T
able A below gives an indication of the relevant table to use as well as the available maximum plate mass per quality.
12. Tables 1- 6 show the minimum and maximum length per width / thickness which can be supplied for both 7 ton max. plates and 10 ton max. plates
Data sheet: A1.3
Available Plate Dimensions Plate Mill products
For further information, contact: ArcelorMittal South Africa Limited, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 2 of 8 File reference: A1.3 Price Lists reference 110 and 111
Table A: Maximum Plate Mass per Quality.
QUALITY DESCRIPTION Table Max. Plate Mass
7 tons 10 tons
15MNB5 AMSA 5 X
ABS/LLOYDS GR A 1 X
ABS/LLOYDS GR EH36 4 X
ASME A516 /ASTM A516 GR65/70 1 X
ASME A516 /ASTM A516 GR65/70+N 3 X
ASME A516/ASTM A516 GR65+N 3 X
ASME SA285/ASTM A285 GRC 1 X
ASME SA516/ASTM A516 GR 70 1 X
ASME SA516/ASTM A516 GR 70+N 3 X
ASME SA516/ASTM A516 GR60 1 X
ASME SA516/ASTM A516 GR60+N 3 X
ASME SA516/ASTM A516 GR65 1 X
ASTM A283-03 GR C 1 X
ASTM A36 1 X
COMMERCIAL QUALITY 2 X
EN 10025-2-235J2+N 3 X
EN 10025-2-S235 J0+AR 1 X
EN 10025-2-S235 JR+AR 1 X
EN 10025-2-S275 JR+AR 1 X
EN 10025-2-S275J0+AR 1 X
EN 10025-2-S275J0+N 3 X
EN 10025-2-S275J2+N 3 X
EN 10025-2-S355J0+AR 2 X
EN 10025-2-S355J0+AR(THICK) 4 X
EN 10025-2-S355J0+N 4 X
EN 10025-2-S355J2+N 4 X
EN 10025-2-S355J2C+N 4 X
EN 10025-2-S355JR+AR 2 X
EN 10025-2-S355JR+N 4 X
EN 10025-3-S355NL 4 X
EN 10028-2-16MO3+N 3 X
EN 10028-2-P235GH+AR 1 X
EN 10028-2-P235GH+N 3 X
EN 10028-2-P265GH+AR 1 X
EN 10028-2-P265GH+AR/BS1501-151/161GR430A 1 X
EN 10028-2-P265GH+N 3 X
EN 10028-2-P265GH+N/BS1501-151/161GR430A 3 X
EN 10028-2-P295GH+AR 1 X
EN 10028-2-P295GH+N 3 X
EN 10028-3-P355NH 4 X
EN 10028-3-P355NL1 4 X
EN 10028-3-P355NL2 4 X
FLANGE/PROFILE CUTTING PLATE 2 X
GALVANISING BATH STEEL 1 X
ROQ LAST TH400 6 X
ROQ TUF AM700 6 X
WEARPLATE 200 5 X
Tolerances Dimensional tolerances of plate produced to international specifications, are in accordance with the tolerances specified in those specifications. For tolerances of other plate mill products refer to the data sheet: Plate Mill Product Tolerances (file reference A1.4).
Supply conditions Plate mill products are supplied in terms of Price Lists 110 and 111 and ArcelorMittal South Africa’s General conditions of Sale.
For further information, contact: ArcelorMittal South Africa Limited, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 3 of 8 File reference: A1.3 Price Lists reference 110 and 111
WIDTH (mm) 5 6 8 10 12 16 20 30 40 50 60 70 80 90 100
Min. 4.0 4.0 4.0 4.0 4.0 6.9 11.7 8.0 5.8 4.5 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.3 5.5 4.8 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.3 5.5 4.8 4.3
Min. 4.0 4.0 4.0 4.0 4.0 6.4 10.9 10.3 7.6 5.9 4.7 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1 6.3 5.6
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1 6.3 5.6
Min. 4.0 4.0 4.0 4.0 4.0 5.9 10.1 9.6 7.0 5.5 4.3 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6 5.9 5.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6 5.9 5.2
Min. 4.0 4.0 4.0 4.0 4.0 5.5 9.5 9.0 6.6 5.1 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2 5.5 4.9
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2 5.5 4.9
Min. 4.0 4.0 4.0 4.0 4.0 5.1 8.9 8.5 6.2 4.8 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 12.6 9.9 8.0 6.7 5.8 5.1 4.6
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.9 8.0 6.7 5.8 5.1 4.6
Min. 4.0 4.0 4.0 4.0 4.0 4.8 8.4 8.0 5.8 4.5 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.4 5.5 4.8 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.4 5.5 4.8 4.3
Min. 13.0 10.8 8.0 7.8 6.3 4.5 7.9 7.5 5.5 4.3 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0 5.2 4.6 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0 5.2 4.6 4.1
Min. 12.3 10.2 7.6 7.3 5.9 4.3 7.5 7.1 5.2 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.7 5.7 4.9 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.8 10.3 8.8 7.6 6.7 6.0
Min. 11.7 9.7 7.2 7.0 5.6 4.0 7.1 6.8 4.9 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.1 8.0 6.4 5.4 4.7 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.2 9.8 8.3 7.3 6.4 5.7
Min. 11.2 9.3 6.8 6.6 5.3 4.0 6.7 6.5 4.7 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.7 7.6 6.1 5.1 4.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.6 9.4 8.0 6.9 6.1 5.4
Min. 10.6 8.8 6.5 6.3 5.1 4.0 6.4 6.2 4.4 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.2 7.3 5.8 4.9 4.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 9.0 7.6 6.6 5.8 5.2
Min. 10.2 8.5 6.2 6.0 4.8 4.0 6.1 5.9 4.2 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 8.8 6.9 5.6 4.7 4.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.6 7.3 6.3 5.6 5.0
Min. 13.6 11.3 8.4 8.2 6.6 4.8 8.3 5.6 4.1 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.5 8.5 6.7 5.3 4.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.9 10.2 8.2 7.0 6.1 5.3 4.7
Min. 13.1 10.9 8.1 7.8 6.3 4.6 7.9 5.4 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.1 6.4 5.1 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.4 9.8 7.9 6.7 5.8 5.1 4.5
Min. 12.6 10.5 7.8 7.5 6.1 4.4 7.6 5.2 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 7.8 6.1 4.9 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.6 6.4 5.6 4.9 4.4
Min. 12.1 10.1 7.5 7.2 5.8 4.2 7.3 5.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.3 7.5 5.9 4.7 4.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.5 9.1 7.3 6.2 5.4 4.7 4.2
Min. 11.7 9.7 7.2 6.9 5.6 4.0 7.0 4.8 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.9 7.2 5.7 4.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.8 7.1 6.0 5.2 4.5 4.0
Min. 11.3 9.4 6.9 6.7 5.4 4.0 6.8 4.6 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.6 7.0 5.5 4.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.8 5.8 5.0 4.4 13.0
Min. 10.9 9.0 6.7 6.4 5.2 4.0 6.5 4.4 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.2 6.8 5.3 4.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.4 8.2 6.6 5.6 4.8 4.2 13.0
Min. 10.5 8.7 6.4 6.2 5.0 4.0 6.3 4.3 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 8.9 6.5 5.1 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 7.9 6.4 5.4 4.6 4.1 13.0
Plate lengths shorter than the indicated min. length or longer than 13 meter may be available on enquiry only.
The minimum and maximum plate lengths for thickness between two columns can be determined by linear interpolation.
7 ton Max. If the cell is empty, plates are not available in these dimensions
On Enquiry Only
THICKNESS (mm)
2900 < W ≤ 3000
3000 < W ≤ 3100
3100 < W ≤ 3200
1200 ≤ W < 1300
1300 ≤ W ≤ 1400
1400 < W ≤ 1500
1500 < W ≤ 1600
1600 < W ≤ 1700
1800 ≤ W ≤ 1900
1900 < W ≤ 2000
2000 < W ≤ 2100
2100 < W ≤ 2200
2200 < W ≤ 2300
2800 < W ≤ 2900
2700 < W ≤ 2800
1700 < W < 1800
2300 < W ≤ 2400
2400 < W ≤ 2500
2500 < W ≤ 2600
2600 < W ≤ 2700
Table 1: Plates supplied As rolled - yield strength < 350 (MPa) Available plate lengths (meter) for width / thickness combinations
For further information, contact: ArcelorMittal South Africa Limited, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 4 of 8 File reference: A1.3 Price Lists reference 110 and 111
Table 2: Plates supplied As rolled - yield strength ≥ 350 (MPa) Available plate lengths (meter) for width / thickness combinations
WIDTH (mm) 5 6 8 10 12 16 20 30 40 50 60 70 80 90 100
Min. 4.0 4.0 4.0 4.0 4.0 6.9 11.7 8.0 5.8 4.5 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.3 5.5 4.8 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.3 5.5 4.8 4.3
Min. 4.0 4.0 4.0 4.0 4.0 6.4 10.9 10.3 7.6 5.9 4.7 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1 6.3 5.6
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1 6.3 5.6
Min. 4.0 4.0 4.0 4.0 4.0 5.9 10.1 9.6 7.0 5.5 4.3 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6 5.9 5.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6 5.9 5.2
Min. 4.0 4.0 4.0 4.0 4.0 5.5 9.5 9.0 6.6 5.1 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2 5.5 4.9
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2 5.5 4.9
Min. 4.0 4.0 4.0 4.0 4.0 5.1 8.9 8.5 6.2 4.8 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 12.6 9.9 8.0 6.7 5.8 5.1 4.6
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.9 8.0 6.7 5.8 5.1 4.6
Min. 4.0 4.0 4.0 4.0 4.0 4.8 8.4 8.0 5.8 4.5 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.4 5.5 4.8 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.4 5.5 4.8 4.3
Min. 13.0 10.8 8.0 7.8 6.3 4.5 7.9 7.5 5.5 4.3 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0 5.2 4.6 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0 5.2 4.6 4.1
Min. 12.3 10.2 7.6 7.3 5.9 4.3 7.5 7.1 5.2 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.7 5.7 4.9 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.8 10.3 8.8 7.6 6.7 6.0
Min. 11.7 9.7 7.2 7.0 5.6 4.0 7.1 6.8 4.9 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.1 8.0 6.4 5.4 4.7 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.2 9.8 8.3 7.3 6.4 5.7
Min. 11.2 9.3 6.8 6.6 5.3 4.0 6.7 6.5 4.7 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.7 7.6 6.1 5.1 4.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.6 9.4 8.0 6.9 6.1 5.4
Min. 10.6 8.8 6.5 6.3 5.1 4.0 6.4 6.2 4.4 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.2 7.3 5.8 4.9 4.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 9.0 7.6 6.6 5.8 5.2
Min. 10.2 8.5 6.2 6.0 4.8 4.0 6.1 5.9 4.2 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 8.8 6.9 5.6 4.7 4.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.6 7.3 6.3 5.6 5.0
Min. 13.6 11.3 8.4 8.2 6.6 4.8 8.3 5.6 4.1 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.5 8.5 6.7 5.3 4.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.9 10.2 8.2 7.0 6.1 5.3 4.7
Min. 13.1 10.9 8.1 7.8 6.3 4.6 7.9 5.4 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.1 6.4 5.1 4.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.4 9.8 7.9 6.7 5.8 5.1 4.5
Min. 12.6 10.5 7.8 7.5 6.1 4.4 7.6 5.2 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 7.8 6.1 4.9 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.6 6.4 5.6 4.9 4.4
Min. 12.1 10.1 7.5 7.2 5.8 4.2 7.3 5.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.3 7.5 5.9 4.7 4.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.5 9.1 7.3 6.2 5.4 4.7 4.2
Min. 11.7 9.7 7.2 6.9 5.6 4.0 7.0 4.8 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.9 7.2 5.7 4.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.8 7.1 6.0 5.2 4.5 4.0
Min. 10.9 9.0 6.7 6.4 5.2 4.0 6.5 4.4 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.6 7.0 5.5 4.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.8 5.8 5.0 4.4 13.0
Min. 10.9 9.0 6.7 6.4 5.2 4.0 6.5 4.4 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.2 6.8 5.3 4.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.4 8.2 6.6 5.6 4.8 4.2 13.0
Min. 10.5 8.7 6.4 6.2 5.0 4.0 6.3 4.3 4.0 4.0 4.0 4.0 4.0 4.0 4.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 8.9 6.5 5.1 4.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 7.9 6.4 5.4 4.6 4.1 13.0
2600 < W ≤ 2700
2700 < W ≤ 2800
2800 < W ≤ 2900
2900 < W ≤ 3000
3000 < W ≤ 3100
3100 < W ≤ 3200
THICKNESS (mm)
1200 ≤ W < 1300
1300 ≤ W ≤ 1400
1400 < W ≤ 1500
1500 < W ≤ 1600
2500 < W ≤ 2600
1600 < W ≤ 1700
1700 < W < 1800
1800 ≤ W ≤ 1900
1900 < W ≤ 2000
2000 < W ≤ 2100
2100 < W ≤ 2200
2200 < W ≤ 2300
2300 < W ≤ 2400
2400 < W ≤ 2500
Plate lengths shorter than the indicated min. Length or longer than 13 meter may be available on enquiry only. The minimum and maximum plate lengths for thickness between two columns can be determined by linear interpolation.
On Enquiry Only
3000 < W ≤ 3100
Min. 4.0
7 ton Max.
10 ton Max. 5.8
If the cell is empty products indicates as available in 7 tons max. only are not available in these dimensions
For further information, contact: ArcelorMittal South Africa Limited, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 5 of 8 File reference: A1.3 Price Lists reference 110 and 111
WIDTH (mm) 6 8 10 12 16 20 30 40 50 60 70 80
Min. 6.0 6.0 6.0 6.0 7.4 12.1 8.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.3 13.0
Min. 6.0 6.0 6.0 6.0 6.9 11.3 10.3 7.6 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1
Min. 6.0 6.0 6.0 6.0 6.4 10.5 9.6 7.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6
Min. 6.0 6.0 6.0 6.0 6.0 9.9 9.0 6.6 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2
Min. 6.0 6.0 6.0 6.0 6.0 9.3 8.5 6.2 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 12.6 9.9 8.0 6.7
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.9 8.0 6.7 13.0
Min. 6.0 6.0 6.0 6.0 6.0 8.8 8.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.4 13.0
Min. 11.3 8.5 8.2 6.8 6.0 8.3 7.5 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0 13.0
Min. 10.8 8.1 7.8 6.4 6.0 7.9 7.1 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.7
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.8 10.3 8.8 7.6
Min. 10.2 7.7 7.4 6.1 6.0 7.5 6.8 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.1 8.0 6.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.2 9.8 8.3 7.3
Min. 9.8 7.3 7.1 6.0 6.0 7.1 6.5 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.7 7.6 6.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.6 9.4 8.0 6.9
Min. 9.3 7.0 6.8 6.0 6.0 6.8 6.2 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.2 7.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 9.0 7.6 6.6
Min. 8.9 6.7 6.5 6.0 6.0 6.5 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.0 8.8 6.9
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.6 7.3 6.3
Min. 11.8 8.9 8.6 7.1 6.0 8.7 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 11.5 8.5 6.7
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.9 10.2 8.2 7.0 6.1
Min. 11.4 8.5 8.3 6.8 6.0 8.3 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.1 6.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.4 9.8 7.9 6.7 13.0
Min. 10.9 8.2 8.0 6.5 6.0 8.0 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 10.7 7.8 6.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.6 6.4 13.0
Min. 10.5 7.9 7.7 6.3 6.0 7.7 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 10.3 7.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.5 9.1 7.3 6.2 13.0
Min. 10.2 7.6 7.4 6.1 6.0 7.4 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 9.9 7.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.8 7.1 6.0 13.0
Min. 9.8 7.4 7.1 6.0 6.0 7.2 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 9.6 7.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.8 13.0 13.0
Min. 9.5 7.1 6.9 6.0 6.0 6.9 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 9.2 6.8
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.4 8.2 6.6 13.0 13.0
Min. 9.2 6.9 6.7 6.0 6.0 6.7 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 8.9 6.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 7.9 6.4 13.0 13.0
Plate lengths shorter than 4.0 meter or longer than 13 meter available on enquiry only.
The minimum and maximum plate lengths for thickness between two columns can be determined by linear interpolation.
7 ton Max. If the cell is empty, plates are not available in these dimensions
On Enquiry Only
2600 < W ≤ 2700
2700 < W ≤ 2800
2800 < W ≤ 2900
2900 < W ≤ 3000
3000 < W ≤ 3100
3100 < W ≤ 3125
1600 < W ≤ 1700
1700 < W < 1800
1800 ≤ W ≤ 1900
1900 < W ≤ 2000
2000 < W ≤ 2100
THICKNESS (mm)
1200 ≤ W < 1300
1300 ≤ W ≤ 1400
1400 < W ≤ 1500
1500 < W ≤ 1600
2100 < W ≤ 2200
2200 < W ≤ 2300
2300 < W ≤ 2400
2400 < W ≤ 2500
2500 < W ≤ 2600
Table 3: Plates supplied normalised - yield strength < 350 (MPa) Available Plate lengths (meter) for width / thickness combinations
For further information, contact: ArcelorMittal South Africa Limited, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 6 of 8 File reference: A1.3 Price Lists reference 110 and 111
WIDTH (mm) 6 8 10 12 16 20 30 40 50 60 70 80
Min. 6.0 6.0 6.0 6.0 7.4 12.1 8.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.3 13.0
Min. 6.0 6.0 6.0 6.0 6.9 11.3 10.3 7.6 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.1 9.7 8.2 7.1
Min. 6.0 6.0 6.0 6.0 6.4 10.5 9.6 7.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.3 9.0 7.6 6.6
Min. 6.0 6.0 6.0 6.0 6.0 9.9 9.0 6.6 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.5 7.2 6.2
Min. 6.0 6.0 6.0 6.0 6.0 9.3 8.5 6.2 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 12.6 9.9 8.0 6.7
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.9 8.0 6.7 13.0
Min. 6.0 6.0 6.0 6.0 6.0 8.8 8.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 11.9 9.4 7.5 6.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.5 6.4 13.0
Min. 11.3 8.5 8.2 6.8 6.0 8.3 7.5 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 8.9 7.1 6.0 13.0
Min. 10.8 8.1 7.8 6.4 6.0 7.9 7.1 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.7
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.8 10.3 8.8 7.6
Min. 10.2 7.7 7.4 6.1 6.0 7.5 6.8 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.1 8.0 6.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.2 9.8 8.3 7.3
Min. 9.8 7.3 7.1 6.0 6.0 7.1 6.5 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 9.7 7.6 6.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.6 9.4 8.0 6.9
Min. 9.3 7.0 6.8 6.0 6.0 6.8 6.2 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.6 9.2 7.3
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 9.0 7.6 6.6
Min. 8.9 6.7 6.5 6.0 6.0 6.5 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.0 8.8 6.9
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.6 8.6 7.3 6.3
Min. 11.8 8.9 8.6 7.1 6.0 8.7 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 11.5 8.5 6.7
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.9 10.2 8.2 7.0 6.1
Min. 11.4 8.5 8.3 6.8 6.0 8.3 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.1 6.4
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.4 9.8 7.9 6.7 13.0
Min. 10.9 8.2 8.0 6.5 6.0 8.0 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 10.7 7.8 6.1
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.9 9.4 7.6 6.4 13.0
Min. 10.5 7.9 7.7 6.3 6.0 7.7 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 10.3 7.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.5 9.1 7.3 6.2 13.0
Min. 10.2 7.6 7.4 6.1 6.0 7.4 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 9.9 7.2
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 8.8 7.1 6.0 13.0
Min. 9.5 7.1 6.9 6.0 6.0 6.9 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 9.6 7.0
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.7 8.4 6.8 13.0 13.0
Min. 9.5 7.1 6.9 6.0 6.0 6.9 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 9.2 6.8
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.4 8.2 6.6 13.0 13.0
Min. 9.2 6.9 6.7 6.0 6.0 6.7 6.0 6.0 6.0 6.0 6.0 6.0
7 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 8.9 6.5
10 ton Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 7.9 6.4 13.0 13.0
Plate lengths shorter than the indicated min. length or longer than 13 meter may be available on enquiry only.
The minimum and maximum plate lengths for thickness between two columns can be determined by linear interpolation.
7 ton Max. If the cell is empty, plates are not available in these dimensions
On Enquiry Only
2600 < W ≤ 2700
2700 < W ≤ 2800
2800 < W ≤ 2900
2900 < W ≤ 3000
3000 < W ≤ 3100
3100 < W ≤ 3125
1600 < W ≤ 1700
1700 < W < 1800
1800 ≤ W ≤ 1900
1900 < W ≤ 2000
2000 < W ≤ 2100
THICKNESS (mm)
1200 ≤ W < 1300
1300 ≤ W ≤ 1400
1400 < W ≤ 1500
1500 < W ≤ 1600
2100 < W ≤ 2200
2200 < W ≤ 2300
2300 < W ≤ 2400
2400 < W ≤ 2500
2500 < W ≤ 2600
Table 4: Plates supplied normalised - yield strength ≥ 350 (MPa) Available Plate lengths (meter) for width / thickness combinations
For further information, contact: ArcelorMittal South Africa Limited, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 7 of 8 File reference: A1.3 Price Lists reference 110 and 111
Table 5: Plate supplied As rolled - Wear resistant plate Available Plate lengths (meter) for width / thickness combinations
WIDTH (mm) 6 8 10 12 16 20 25 30 35 40 45 50 60
Min. 4.0 4.0 4.0 4.0 6.9 11.7 9.8 8.0 6.8 5.8 5.1 4.5 4.0
Max. 13.0 13.0 13.0 13.0 13.0 11.9 10.5 9.4 7.5
Min. 4.0 4.0 4.0 4.0 6.4 10.9 12.5 10.3 8.7 7.6 6.7 5.9 4.7
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.1 9.7
Min. 4.0 4.0 4.0 4.0 5.9 10.1 11.7 9.6 8.1 7.0 6.2 5.5 4.3
Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.6 11.3 9.0
Min. 4.0 4.0 4.0 4.0 5.5 9.5 10.9 9.0 7.6 6.6 5.8 5.1 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 11.8 10.6 8.5
Min. 4.0 4.0 4.0 4.0 5.1 8.9 10.3 8.5 7.1 6.2 5.4 4.8 4.0
Max. 13.0 13.0 13.0 13.0 13.0 12.6 11.1 9.9 8.0
Min. 4.0 4.0 4.0 4.0 4.8 8.4 9.7 8.0 6.7 5.8 5.1 4.5 4.0
Max. 13.0 13.0 13.0 13.0 13.0 11.9 10.5 9.4 7.5
Min. 10.8 8.0 7.8 6.3 4.5 7.9 9.2 7.5 6.4 5.5 4.8 4.3 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.9 11.2 9.9 8.9 7.1
Min. 10.2 7.6 7.3 5.9 4.3 7.5 8.7 7.1 6.0 5.2 4.5 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.3 10.7 9.4 8.4 6.7
Min. 9.7 7.2 7.0 5.6 4.0 7.1 8.3 6.8 5.7 4.9 4.3 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.7 10.1 9.0 8.0 6.4
Min. 9.3 6.8 6.6 5.3 4.0 6.7 7.9 6.5 5.4 4.7 4.1 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.2 9.7 8.5 7.6 6.1
Min. 8.8 6.5 6.3 5.1 4.0 6.4 7.5 6.2 5.2 4.4 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.6 10.7 9.2 8.2 7.3 5.8
Min. 8.5 6.2 6.0 4.8 4.0 6.1 7.2 5.9 4.9 4.2 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 10.2 8.8 7.8 6.9 5.6
Min. 11.3 8.4 8.2 6.6 4.8 8.3 6.9 5.6 4.7 4.1 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.5 9.8 8.5 7.5 6.7 5.3
Min. 10.9 8.1 7.8 6.3 4.6 7.9 6.6 5.4 4.5 4.0 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 13.0 11.1 9.4 8.1 7.2 6.4 5.1
Min. 10.5 7.8 7.5 6.1 4.4 7.6 6.4 5.2 4.3 4.0 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.9 10.7 9.0 7.8 6.9 6.1 4.9
Min. 10.1 7.5 7.2 5.8 4.2 7.3 6.1 5.0 4.2 4.0 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.5 10.3 8.7 7.5 6.6 5.9 4.7
Min. 9.7 7.2 6.9 5.6 4.0 7.0 5.9 4.8 4.0 4.0 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.0 9.9 8.4 7.2 6.4 5.7 4.5
Min. 9.4 6.9 6.7 5.4 4.0 6.8 5.7 4.6 4.0 4.0 4.0 4.0 4.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 11.6 9.6 8.1 7.0 6.2 5.5 4.4
Min. 9.0 6.7 6.4 5.2 4.0 6.5 5.5 4.4 4.0 4.0 4.0 4.0 4.0
Max. 13.5 16.0 19.0 13.0 13.0 13.0 11.2 9.2 7.8 6.8 5.9 5.3 4.2
Min. 8.7 6.4 6.2 5.0 4.0 6.3 5.3 4.3 4.0 4.0 4.0 4.0 4.0
Max. 13.5 16.0 19.0 13.0 13.0 13.0 10.9 8.9 7.6 6.5 5.7 5.1 4.1
THICKNESS (mm)
3000 < W ≤ 3100
3100 < W ≤ 3200
2400 < W ≤ 2500
2500 < W <= 2600
2600 < W ≤ 2700
2700 < W ≤ 2800
2800 < W ≤ 2900
2900 < W ≤ 3000
2300 < W ≤ 2400
1200 ≤ W ≤ 1300
1300< W ≤ 1400
1400 < W ≤ 1500
1500 < W ≤ 1600
1600 < W ≤ 1700
2200 < W ≤ 2300
1700 < W < 1800
1800 ≤ W ≤ 1900
1900 < W ≤ 2000
2000 < W ≤ 2100
2100 < W ≤ 2200
Plate lengths shorter than the indicated min. length or longer than 13 meter may be available on enquiry only The minimum and maximum plate lengths for thickness between two columns can be determined by linear interpolation. Wear plate > 8 mm to 20 mm sides uncut (cut-to-length only) Only available as 7 tons max.
On enquiry only
For further information, contact: ArcelorMittal South Africa Limited, PO Box 2, Vanderbijlpark 1900. www.arcelormittal.com/southafrica Care has been taken to ensure that the information in this data sheet is accurate. ArcelorMittal South Africa does not, however, assume responsibility for any inaccuracies or misinterpretations of this data. We are continuously engaged in product development and revised data sheets will be issued from time to time. Please ensure that you have the most recent issue. Effective date: December 2016
Page 8 of 8 File reference: A1.3 Price Lists reference 110 and 111
Table 6: Plates suppled Quenched or Quenched & Tempered Available plate lengths (meter) for width / thickness combinations
WIDTH (mm) 8 10 12 16 20 25 30 35 40 45 50
Min. 6.0 8.7 6.9 8.0 6.8 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 11.9 10.5 9.4 8.2 7.5
Min. 6.0 6.0 8.1 6.4 10.3 8.7 7.6 6.7 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 13.0 13.0 12.1 10.6 9.7
Min. 6.0 6.0 7.6 6.0 9.6 8.1 7.0 6.2 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 13.0 12.6 11.3 9.9 9.0
Min. 6.0 6.0 7.1 6.0 9.0 7.6 6.6 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 13.0 11.8 10.6 9.3 8.5
Min. 6.0 6.0 6.6 9.3 8.5 7.1 6.2 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 12.6 11.1 9.9 8.7 8.0
Min. 6.0 6.0 6.3 8.8 8.0 6.7 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 11.9 10.5 9.4 8.3 7.5
Min. 6.8 6.8 6.0 8.3 7.5 6.4 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 13.0 12.9 11.2 9.9 8.9 7.8 7.1
Min. 6.4 6.5 6.0 7.9 7.1 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 13.0 12.3 10.7 9.4 8.4 7.4 6.7
Min. 6.1 6.1 6.0 7.5 6.8 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 13.0 11.7 10.1 9.0 8.0 7.1 6.4
Min. 6.0 6.0 6.0 7.1 6.5 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 13.0 11.2 9.7 8.5 7.6 6.7 6.1
Min. 6.0 6.0 6.0 6.8 6.2 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 12.6 10.7 9.2 8.2 7.3 6.4
Min. 6.0 6.0 6.0 6.5 6.0 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 12.0 10.2 8.8 7.8 6.9 6.1
Min. 7.1 7.1 6.2 8.7 6.0 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 11.5 9.8 8.5 7.5 6.7
Min. 6.8 6.8 6.0 8.3 6.0 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 11.1 9.4 8.1 7.2 6.4
Min. 6.5 6.6 6.0 8.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 10.7 9.0 7.8 6.9 6.1
Min. 6.3 6.3 6.0 7.7 6.0 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 10.3 8.7 7.5 6.6
Min. 6.1 6.1 6.0 7.4 6.0 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 9.9 8.4 7.2 6.4
Min. 6.0 6.0 6.0 6.9 6.0 6.0 6.0 6.0 6.0 6.0 6.0
Max. 13.0 13.0 13.0 13.0 9.6 8.1 7.0 6.2
THICKNESS (mm)
2400 < W ≤ 2500
2500 < W ≤ 2600
2600 < W ≤ 2700
2700 < W ≤ 2800
2800 < W ≤ 2900
2900 < W ≤ 3000
2300 < W ≤ 2400
1200 ≤ W ≤ 1300
1300 < W ≤ 1400
1400 < W ≤ 1500
1500 < W ≤ 1600
1600 < W ≤ 1700
2200 < W ≤ 2300
1700 < W < 1800
1800 ≤ W ≤ 1900
1900 < W ≤ 2000
2000 < W ≤ 2100
2100 < W ≤ 2200
Plate lengths shorter than the indicated min. length or longer than 13 meter may be available on enquiry only. The minimum and maximum plate lengths for thickness between two columns can be determined by linear interpolation. Only available as 7 tons max.
On enquiry only
Top Related