The DA-Series is distinguished from conventional
amplifiers by its intelligent computer control. The DA
amplifiers employ shaft-encoder controls and LCD
displays. They offer superb thermal stability, ultra-low
distortion, and unprecedented reliability. DA amplifiers
utilize an industry-first electronic circuit breaker which
may be remotely reset through network control.
All three models are based on third generation bi-
polar transistor technology for the utmost in confidence
and freedom from long-term degradation of sound
quality.
The DA-Series offers many additional practical
features, such as a front panel, removable air filter for
ease in cleaning and adjustable rear rack ears. DA
amplifiers are also available with built-in loudspeaker
processors for single-amped, bi-amped, and subwoofer
loudspeaker models.
An on-board microprocessor continually monitors
all critical internal functions and sends status reports to
the front panel information display. The vital
information that the computer provides, such as driver
impedance and line voltage, can greatly aid the
professional in quickly troubleshooting or verifying
proper system performance.
DigitalAmplifiers
Description: Quick Data:
Highlights:
DA-SeriesAvailable Models:DA-600, DA-700, & DA-800
Available displays are:• CChhaannnneell OOnn//OOffff ((MMuuttee SSttaattee))
• PPhhaassee SSttaattee
• OOuuttppuutt VVoollttaaggee
• OOuuttppuutt WWaattttaaggee
• LLooaadd IImmppeeddaannccee
• AACC MMaaiinnss VVoollttaaggee
• TTeemmppeerraattuurree
• AAtttteennuuaattiioonn LLeevveellss (in 0.5 dB increments) with complete independence of the channels
DA-800
DA-700
DA-600
660
545
500
975
775
600
910
700
600
1880
1550
1200
1820 <.007%
<.007%
<.007%
60 (27.2)
60 (27.2)
60 (27.2)
1400
1200
AMPLIFIERQUICKCHART
8 4 2 8 4
Pow
er O
utpu
t
ohm
s
Bridge
d M
ono
ohm
s
THD
(4 o
hms,
1 k
Hz, 4
00W
)W
eigh
tlb
s. (k
g)
2001 APOGEE SOUND INTL., LLC 05/01Specifications subject to change without notice. A 42-0833 / B 55-0034-01R1 Printed in U.S.A.
DA-800 Front View
DA-800 Rear View
Technical Specifications:
FREQUENCY RESPONSE:20 Hz to 20 kHz, +0, -0.3dB, at all power levels
THD: < 0.007% (4 ohms, 1 kHz, 400W)
SMPTE INTERMODULATION DISTORTION (IMD):< 0.01%, 60 Hz & 7 kHz, rated power @ 8 ohms
SLEW RATE: 35V/microsecond, input filter bypassed
DAMPING FACTOR: 400:1, 1 kHz @ 8 ohms
INPUT COMMON MODE REJECTION (CMR):Greater than 90 dB
VOLTAGE GAIN: 40x 32 dB
INPUT SENSITIVITY: For rated power @ 4 ohms;DA-800: 1.53V, DA-700: 1.36V, DA-600 : 1.2V
INPUT IMPEDANCE: 13k ohms, balanced
HUM and NOISE: Better than -117 dBA
CROSSTALK: Better than -80 dBA
CONNECTORS: Input - XLR balanced, output - 5-way binding posts
COOLING: Front-to-rear tunnel, dual variable speed DC fans
CONTROLS: DA-Series: two front panel detented shaft encoder Level controls,channel Link switch, level control Lock switch, Display toggleswitch, Stereo/Bridge switch, Ground Lift switch
CHANNEL INDICATORS:DA-Series: Large backlit liquid crystal display for each channelshowing: Channel On/Off (Mute State), Phase State, OutputVoltage, Output Wattage, Load Impedance, AC Mains Voltage,Temperature, and Attenuation Levels (in 0.5dB increments); eachchannel also has a Clip LED, Limit LED, Signal LED, Fault LED andReady LED
LIMITED WARRANTY: Apogee Sound International products, sold in the U.S.A., are
warranted to be free from defects in materials and workmanship from the date of original
purchase for a period of five (5) years for amplifiers and a period of one (1) year for other
equipment. If a malfunction occurs, the unit will be repaired or replaced, at our option,
provided it is shipped prepaid to an authorized Apogee Service Facility. This warranty
does not extend to finish; appearance items; or any product malfunctions due to abuse,
accident, misuse, negligence, misapplication, or improper operation. Other conditions
apply. Contact Apogee for further information.
2180 South McDowell Blvd.Petaluma, CA 94954 USATel: 707-778-8887 Fax: 707-778-6923 www.apogee-sound.com
MASTER INDICATORS: LEDs indicating power on/off status,network control status and breaker trip warning
PROTECTION: Electronic circuit breaker (may be remotely reset),high temperature, DC, turn-on delay with power ramp-up,ultrasonic, short circuit
LINE VOLTAGE: 100/120/220-240 VAC internally userconfigurable, electronic circuit breaker
CONSTRUCTION: 16-gauge welded steel chassis, 10-gaugecontinuous front-to-rear side rails with front and rear rack ears
DIMENSIONS: 19" (483mm) W x 3.5" (89mm) H (2 EIU rackspaces) x 18.5" (470mm) D
WEIGHT: 60 lbs. (27.2 kg)
Top Related