8/14/2019 Automotive Rotisserie Plan Set
1/12
Automotive Rotisserie Plan Set
Page: Part Description:
1 Title Page2 Misc. Pictures3 Misc. Pictures continued4 Main Supports5 Upright sliders6 Front Frame adapter (early Mustang shown)7 Rear Frame adapter (early Mustang shown)8 Pivot Pins9 Tow bar adapter10 Hoist adapter11 Alternate plans and tips12 Complete parts listing13 Parts listing continued
8/14/2019 Automotive Rotisserie Plan Set
2/12
Part C Slider
Part A Main Supports
Part B Side Supports
Part E Rear FrameAdapter
8/14/2019 Automotive Rotisserie Plan Set
3/12
Part F Pivot Pin
Part D Front FrameAdapter
Detail of coupler for:
Main Support (A)
Side Support (B)
8/14/2019 Automotive Rotisserie Plan Set
4/12
60.00in
2.00in
24.00in
3.00in
0.75in
1.5in
0.25in
All tubing is .250 wall
Main supports (x2)
2.50in
8/14/2019 Automotive Rotisserie Plan Set
5/12
24.000in
0.875x 3 places
in
2.000in1.500in
12.000in
6.000in
10.000in
36.000in
3.000
13.500in
Main Extensions ( x 2 ) Outr
All tubing .250 wall
Cap ends with .250 plate
5.000in
8/14/2019 Automotive Rotisserie Plan Set
6/12
32.000in
2.500in
3.250in
1.750in
1.500in
1.5000in
6.000in
2.000in
0.500in
Pivot Pin ( 2 required )
3.250in
0.500in
8/14/2019 Automotive Rotisserie Plan Set
7/12
49in
1in
Drill holes to match bumper mounting holes
2in
1/4in
3in
1/2in1 1/2in
Insert Pivot Pin
8/14/2019 Automotive Rotisserie Plan Set
8/12
Part 2
Part 1
9 1/4in
1 1/2in
3 1/4in
2in
1/4 Wall Tubingin
1/2in
5 1/4in
1/2in
Pivot Pin (x2)
8/14/2019 Automotive Rotisserie Plan Set
9/12
36in
1 5/8in
1/2in
This adapter slides into the Front Frame Adapter (page 6) inplace of the pivot pin.
8/14/2019 Automotive Rotisserie Plan Set
10/12
As Required for applicationin
3in 3in
3/8in 3/8in
Replace outriggers with one tube per side ofcar. Length will determined by specific car. H
3/8in
1 1/2in 1 1/2in
3/8in
3in
2in
5in
Weld to top of slider assembly to allow cherry picker to raise or lower end of car
You can use a bumper jack or long-ram jack to raise and lower car.
A flat bottom long-ram jackshould be used if you plan on using a long -ram jack.1/2in
8/14/2019 Automotive Rotisserie Plan Set
11/12
Bill of Materials
Description: Part: Qty Required: Materials:
Main Supports A 2 2 X 3 X .25 Tubing 60 Each
A 4 2 X 2 X .25 Tubing 3 EachA 2 1 X 1 X .25 Tubing 21 Each
A 2 Hitch Pins (Upright Pins)A 4 5/16 Hitch Pins (Side Support Pins)
Side Supports B 4 1 X 1 X .25 Tubing 36 Each
B 8 1 X 1 X .25 plate (end caps)
Sider Assembly C 2 2 X 2 X .25 Tubing 24 Each
C 2 2 O.D. X 1.5 I.D Tubing 5 Each
Front Adapter * As needed to adapt to your specific vehicle, early Mustang parts listed:D 1 1 X 1 X .25 Tubing 32
D 2 2 X .25 flat 12 EachD 1 2 X 2 X .25 Tubing 3
D 1 3/8 X 3 Grade 5 Bolt / Nut
Rear Adapter * As needed to adapt to your specific vehicle, early Mustang parts listed:E 1 1 X 3 X .187 Tubing ???????
E 1 2 X 2 X .25 Tubing 3
E 1 3/8 X 3 Grade 5 Bolt / Nut
Pivot Pins F 2 1 Round Solid 9 EachF 2 2 X 2 X .25 Tubing 3 EachF 2 1 Shaft Collars
F 1 Hitch Pin (Position Lock, front only)
Tow Bar Adapter
G 1 2 X 2 X .25 Tubing 48
G 1 Hitch Adapter
Hoist Adapter H 1 2 X 2 X .25 Tubing 6
H 1 2 X 2 X .25 Tubing 48
H 2 2 flat 6 EachH 1 2 X 3 X .187 Tubing 48
H 1 X 3 flat 3
H 2 3/8 X 1 Flat 2 Each
8/14/2019 Automotive Rotisserie Plan Set
12/12
Options:
Ram Mounts for uprights 2 X 4 flat 4 Each
4 3/8 X 2 flat 3 Each
Hoist lifting eyes 2 u-bolts
Top Related