WIFI ANTENNA
Connect to CARPLAY-USB cable
Multimedia USB RGB input cable
Update adapter
Connect to the Phone's original cable
Optional cable
Connect to RGB output device
C6/C7 switch wiring for A/C panel or gateway box.(A8 using spreaded out line)
Blue & white wire for MMI controlConnect to PIN10 of the headunit's ISO power socket
Connect to the original headunit's big ISO connector (The position of the green inserts)
RED---12V output for rear view camera
ORANGE--Reverse control cable (connect to reversing light) for AVM /without reversing gridline
YELLOW---RCA Front/Rear video input(Connect to front /rear view camera/360 AVM/DVR
Stereo audio cableBLACK---Stereo audio output
Power cable
Microphone
Connect to A/C panel or gateway box port
Connect to cable pulled fromA/C panel or gateway box port
Connect to the original headunit's cable (The original cable is gray).
Plug into the original headunit's LVDS port
Connect to the unplugged greeninserts from the original headunit'sISO cable
Reset Dip Switch LED
OFF
ON
PIN 4 OFF/ON
PIN 6 OFF/ON
PIN 7 OFF/ONPIN 8 OFF/ON
Reversing gridline/Enable 360 panoramic
Rear view camera CVBS input / RGB input
Aftermarket rear view CAM/Original rear view CAM
PIN 1 PIN 2 PIN 3 PIN 5 CAR MODEL
ON OFF OFF OFF
ON OFF ON OFF
OFF OFF ON OFF
ON ON OFF OFF
OFF ON OFF OFF
OFF OFF OFF OFF
OFF OFF OFF ON
ON OFF OFF ON
ON OFF ON ON
OFF OFF ON ON
OFF ON ON ON
Audi (A6/Q3/Old Q7) WIRING DIAGRAM
2010~2012 A6L/A7(C6) CAN1 connect to gateway box10-12 Q7 (7") CAN 1 connect to A/C beige socket's pin7&pin8
13-15 A6/A7/A8(C7) CAN1 connect to A/C red socket's pin4&5
09~18 A4/A5/Q5 CAN1 connect to gateway box's red socket's pin5&pin15 .(Gateway bos is in the left side of the co-pilot)High-end 7" A1/Q3 CAN1 connect to gateway box's (Under the steering wheel)pin5&15 or to A/C panel's beige socket's pin12&13Low-end 6.5" A1/Q3 CAN1 connect to gateway box's (Under the steering wheel)pin5&15 or to A/C panel's beige socket's pin12&13USA version A4/A5/Q5 CAN1 connect to gateway box's red socket's pin5&pin15 .(Gateway bos is in the left side of the co-pilot)
USA version Q7 (6.5") CAN1 connect to A/C beige socket's pin7&8
17~18 A4/Q7(7") CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7; 09~11 Q7 MMI bule&white wire connect to pin3
16~18 A6/A7/A8l CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7; MMI system bule&white wire connect to pin3
A3(7") CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7
Q3/A3(5.8") CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7
LCD OUT cable (must not be extended)
LCD IN cable (must not be extended)
Microphone cable
DIP SWITCH SETTING(After changing the dip code,press "reset"or power-on again)
ampireLDS INTERFACE
ampireLDS INTERFACE
ampire
NG/Touch point coordinate correction PIN7 “ON”, after configuration PIN7 “OFF”
REMARK: Please stay in the AUX Interface when opening the CARPLAY Interface
1) For A6/A7, long press and hold the “NAV” Button to enter the Interface, long press the “NAV” Button again to exit.2) Short press “TEL” Button to open “Siri”.3) Knob to control up/down/right/left/ok.
1) For A1/Q3, long press and hold the Voice control Button to enter the Interface, long press the Voice control Button again to exit.2) Short press the Voice control Button to open “Siri”.3) Steering wheel Roller to control up/down/ok.
Top Related