@AIRBUSA318/A319/A320/A321
AIRCRAFT RECOVERY MANUAL
ARM
The content of this document is the property of Airbus.It is supplied in confidence and commercial security on its contents must be maintained.It must not be used for any purpose other than that for which it is supplied, nor mayinformation contained in it be disclosed to unauthorized persons.It must not be reproduced in whole or in part without permission in writing from the owners ofthe copyright. Requests for reproduction of any data in this document and the media authorizedfor it must be addressed to Airbus.
© AIRBUS S.A.S. 2005. All rights reserved.
AIRBUS S.A.S.Customer Services
Technical Data Support and Services31707 Blagnac Cedex
FRANCE
Issue: Jun 01/08 Rev: Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
HIGHLIGHTS
Revision No. 2 - Jul 01/09
LOCATIONS CHGCODE
DESCRIPTIONS OF CHANGE
CHAPTER 01
Subject 01-20-01
DESC 01-20-01-002-A01 R
CHAPTER 02
Subject 02-00-00
DESC 02-00-00-001-A01 R UPDATED DEFINITION OF SECONDARYDAMAGE
Subject 02-30-01
TASK 02-30-01-200-801-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
TASK 02-30-01-481-801-A01 R TOOL P/N AND/OR DESIGNATIONADDED/REVISED/DELETED
TASK 02-30-01-867-802-A01 R TOOL P/N AND/OR DESIGNATIONADDED/REVISED/DELETED
CHAPTER 03
Subject 03-00-00
TASK 03-00-00-558-801-A01 R
FIGURE 03-00-00-991-002-D01 R
Subject 03-20-02
TASK 03-20-02-970-801-A01 R UPDATED AMM TASKCROSS REFERENCED MANUAL(S)ADDED/REVISED/DELETED
Subject 03-50-01
TASK 03-50-01-558-809-A01 R ADDED CAPACITY DATA IN THE TABLE
TASK 03-50-01-558-811-A01 R ADDED NOTE AND CORRECTIVECLERICAL ERRORNOTE AMENDED
TASK 03-50-01-558-811-B01 R ADDED NOTE AND CORRECTIVECLERICAL ERRORNOTE AMENDED
HIGHLIGHTSPage 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
LOCATIONS CHGCODE
DESCRIPTIONS OF CHANGE
TASK 03-50-01-558-811-C01 R ADDED NOTE AND CORRECTIVECLERICAL ERRORNOTE AMENDED
Subject 03-60-01
DESC 03-60-01-001-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
CHAPTER 04
Subject 04-20-00
TASK 04-20-00-588-801-A01 R
Subtask 04-20-00-588-001-A01 R
FIGURE 04-20-00-991-001-A01 N ILLUSTRATION ADDED
FIGURE 04-20-00-991-001-B01 N ILLUSTRATION ADDED
FIGURE 04-20-00-991-001-C01 N ILLUSTRATION ADDED
FIGURE 04-20-00-991-001-D01 N ILLUSTRATION ADDED
CHAPTER 05
Subject 05-40-02
TASK 05-40-02-650-801-A01 R WARNING CAUTIONADDED/REVISED/DELETED
CHAPTER 06
Subject 06-00-00
DESC 06-00-00-002-A01 N
FIGURE 06-00-00-991-001-A01 N ILLUSTRATION ADDED
FIGURE 06-00-00-991-001-B01 N ILLUSTRATION ADDED
FIGURE 06-00-00-991-001-C01 N ILLUSTRATION ADDED
Subject 06-10-00
TASK 06-10-00-970-801-A01 R
TASK 06-10-00-970-803-A01 R
Subject 06-30-00
DESC 06-30-00-001-A01 R ADDED PERMISSIBLE WIND SPEEDWARNING CAUTIONADDED/REVISED/DELETED
FIGURE 06-30-00-991-010-A01 N ILLUSTRATION ADDED
HIGHLIGHTSPage 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
LOCATIONS CHGCODE
DESCRIPTIONS OF CHANGE
DESC 06-30-00-001-B01 R ADDED PERMISSIBLE WIND SPEEDWARNING CAUTIONADDED/REVISED/DELETED
FIGURE 06-30-00-991-011-A01 N ILLUSTRATION ADDED
DESC 06-30-00-001-C01 R ADDED PERMISSIBLE WIND SPEEDWARNING CAUTIONADDED/REVISED/DELETED
FIGURE 06-30-00-991-012-A01 N ILLUSTRATION ADDED
DESC 06-30-00-001-D01 R ADDED PERMISSIBLE WIND SPEEDWARNING CAUTIONADDED/REVISED/DELETED
FIGURE 06-30-00-991-013-A01 N ILLUSTRATION ADDED
TASK 06-30-00-581-802-A01 R TOOL P/N AND/OR DESIGNATIONADDED/REVISED/DELETEDWARNING CAUTIONADDED/REVISED/DELETED
Subtask 06-30-00-581-003-A01 R CAUTION DELETED AS NOT APPLICABLEWARNING CAUTIONADDED/REVISED/DELETED
TASK 06-30-00-581-801-A01 R UPDATED REFERENCE TO AIRCRAFTSTABILITY ON JACKSCROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETEDWARNING CAUTIONADDED/REVISED/DELETEDNOTE AMENDED
Subtask 06-30-00-581-002-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
Subject 06-40-00
HIGHLIGHTSPage 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
LOCATIONS CHGCODE
DESCRIPTIONS OF CHANGE
DESC 06-40-00-002-A01 R DELETED INFORMATION RELATED TOFUSELAGE LIFTING WITH PNEUMATICLIFTING BAGSADDED REFERENCE TO LEVELING ANDLIFTING PROCEDURES ON WING ANDFUSELAGECROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
DESC 06-40-00-001-A01 N
DESC 06-40-00-003-A01 N
FIGURE 06-40-00-991-001-A01 N ILLUSTRATION ADDED
FIGURE 06-40-00-991-003-A01 N ILLUSTRATION ADDED
TASK 06-40-00-581-801-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETEDWARNING CAUTIONADDED/REVISED/DELETEDNOTE AMENDED
Subtask 06-40-00-581-001-A01 R UPDATED PROCEDURE TITLE LAYOUTAND TECHNICAL CONTENTCROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
Subject 06-50-00
TASK 06-50-00-581-803-A01 R
TASK 06-50-00-581-802-A01 R
TASK 06-50-00-581-801-A01 R TOOL P/N AND/OR DESIGNATIONADDED/REVISED/DELETEDCROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETEDWARNING CAUTIONADDED/REVISED/DELETEDNOTE AMENDED
Subtask 06-50-00-581-001-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
CHAPTER 07 R
Subject 07-00-00
HIGHLIGHTSPage 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
LOCATIONS CHGCODE
DESCRIPTIONS OF CHANGE
DESC 07-00-00-002-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
Section 07-20 N
Subject 07-20-00 N
DESC 07-20-00-001-A01 N
FIGURE 07-20-00-991-001-A01 N ILLUSTRATION ADDED
Section 07-40 R
Subject 07-40-00 R
DESC 07-40-00-001-A01 R Added of debogging definition
Subject 07-40-01
TASK 07-40-01-584-801-A01 R
Subject 07-40-02
TASK 07-40-02-584-801-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETEDTOOL P/N AND/OR DESIGNATIONADDED/REVISED/DELETED
TASK 07-40-02-584-802-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETEDCONSUMABLE MATERIAL DATAUPDATEDTOOL P/N AND/OR DESIGNATIONADDED/REVISED/DELETED
Subject 07-60-02
DESC 07-60-02-001-A01 R CROSS REFERENCED DOCUMENTARYUNIT ADDED/REVISED/DELETED
CHAPTER 09
Subject 09-20-01
DESC 09-20-01-002-A01 R
FIGURE 09-20-01-991-006-A01 R
FIGURE 09-20-01-991-008-A01 R
FIGURE 09-20-01-991-010-A01 R
FIGURE 09-20-01-991-012-A01 R
FIGURE 09-20-01-991-015-A01 R
FIGURE 09-20-01-991-016-A01 D ILLUSTRATION DELETED
HIGHLIGHTSPage 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
LOCATIONS CHGCODE
DESCRIPTIONS OF CHANGE
Subject 09-50-01
FIGURE 09-50-01-991-007-A01 R
HIGHLIGHTSPage 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
LIST OF EFFECTIVE CONTENT
Revision No. 2 - Jul 01/09
CONTENT CHGCODE
LAST REVISIONDATE
CHAPTER 01
Subject 01-00-00
DESC 01-00-00-001-A01 Jun 01/08
DESC 01-00-00-002-A01 Jun 01/08
Subject 01-00-02
DESC 01-00-02-001-A01 Nov 01/08
FIGURE 01-00-02-991-001-A01 Jun 01/08
FIGURE 01-00-02-991-002-A01 Jun 01/08
DESC 01-00-02-002-A01 Jun 01/08
DESC 01-00-02-003-A01 Jun 01/08
DESC 01-00-02-004-A01 Jun 01/08
Subject 01-00-03
DESC 01-00-03-001-A01 Jun 01/08
Subject 01-10-01
DESC 01-10-01-002-A01 Jun 01/08
DESC 01-10-01-001-A01 Jun 01/08
Subject 01-20-01
DESC 01-20-01-001-A01 Jun 01/08
DESC 01-20-01-002-A01 R Jul 01/09
DESC 01-20-01-002-B01 Jun 01/08
DESC 01-20-01-002-C01 Jun 01/08
DESC 01-20-01-002-D01 Jun 01/08
CHAPTER 02
Subject 02-00-00
DESC 02-00-00-001-A01 R Jul 01/09
FIGURE 02-00-00-991-001-A01 Jun 01/08
L.E.C.Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
Subject 02-10-01
DESC 02-10-01-001-A01 Jun 01/08
DESC 02-10-01-002-A01 Jun 01/08
Subject 02-20-01
TASK 02-20-01-285-801-A01 Jun 01/08
Subtask 02-20-01-284-001-A01 Jun 01/08
Subtask 02-20-01-680-001-A01 Jun 01/08
Subtask 02-20-01-862-001-A01 Jun 01/08
Subtask 02-20-01-869-001-A01 Jun 01/08
Subject 02-20-02
TASK 02-20-02-285-801-A01 Jun 01/08
Subtask 02-20-02-285-001-A01 Jun 01/08
Subtask 02-20-02-285-002-A01 Jun 01/08
Subtask 02-20-02-500-001-A01 Jun 01/08
Subtask 02-20-02-869-001-A01 Jun 01/08
Subject 02-30-01
TASK 02-30-01-200-801-A01 R Jul 01/09
Subtask 02-30-01-867-001-A01 Nov 01/08
Subtask 02-30-01-867-003-A01 Nov 01/08
Subtask 02-30-01-867-004-A01 Nov 01/08
FIGURE 02-30-01-991-001-A01 Jun 01/08
FIGURE 02-30-01-991-002-A01 Jun 01/08
TASK 02-30-01-481-801-A01 R Jul 01/09
Subtask 02-30-01-481-003-A01 Jun 01/08
Subtask 02-30-01-481-004-A01 Jun 01/08
FIGURE 02-30-01-991-020-A01 Jun 01/08
FIGURE 02-30-01-991-021-A01 Jun 01/08
TASK 02-30-01-867-802-A01 R Jul 01/09
Subtask 02-30-01-869-001-A01 Jun 01/08
L.E.C.Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
Subtask 02-30-01-581-001-A01 Nov 01/08
Subtask 02-30-01-581-002-A01 Nov 01/08
Subtask 02-30-01-581-003-A01 Nov 01/08
FIGURE 02-30-01-991-019-A01 Jun 01/08
FIGURE 02-30-01-991-022-A01 Jun 01/08
FIGURE 02-30-01-991-023-A01 Jun 01/08
Subject 02-40-01
DESC 02-40-01-001-A01 Jun 01/08
CHAPTER 03
Subject 03-00-00
TASK 03-00-00-558-801-A01 R Jul 01/09
Subtask 03-00-00-558-001-A01 Nov 01/08
Subtask 03-00-00-558-001-B01 Nov 01/08
Subtask 03-00-00-558-001-C01 Nov 01/08
Subtask 03-00-00-558-001-D01 Nov 01/08
Subtask 03-00-00-970-001-A01 Jun 01/08
FIGURE 03-00-00-991-002-A01 Jun 01/08
FIGURE 03-00-00-991-002-B01 Jun 01/08
FIGURE 03-00-00-991-002-C01 Jun 01/08
FIGURE 03-00-00-991-002-D01 R Jul 01/09
Subject 03-20-01
DESC 03-20-01-001-A01 Nov 01/08
FIGURE 03-20-01-991-001-A01 Nov 01/08
DESC 03-20-01-002-A01 Nov 01/08
Subject 03-20-02
TASK 03-20-02-970-801-A01 R Jul 01/09
Subtask 03-20-02-869-001-A01 Nov 01/08
Subtask 03-20-02-970-001-A01 Jun 01/08
FIGURE 03-20-02-991-001-A01 Jun 01/08
L.E.C.Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 03-20-02-991-001-B01 Jun 01/08
FIGURE 03-20-02-991-002-A01 Jun 01/08
Subject 03-50-01
DESC 03-50-01-001-A01 Jun 01/08
TASK 03-50-01-558-801-A01 Nov 01/08
Subtask 03-50-01-558-001-A01 Nov 01/08
TASK 03-50-01-558-801-B01 Nov 01/08
Subtask 03-50-01-558-018-A01 Nov 01/08
FIGURE 03-50-01-991-003-A01 Jun 01/08
FIGURE 03-50-01-991-004-A01 Jun 01/08
TASK 03-50-01-558-801-C01 Nov 01/08
Subtask 03-50-01-558-019-A01 Nov 01/08
FIGURE 03-50-01-991-005-A01 Jun 01/08
FIGURE 03-50-01-991-006-A01 Jun 01/08
TASK 03-50-01-558-801-D01 Nov 01/08
Subtask 03-50-01-558-020-A01 Nov 01/08
FIGURE 03-50-01-991-007-A01 Jun 01/08
FIGURE 03-50-01-991-008-A01 Jun 01/08
TASK 03-50-01-558-802-A01 Nov 01/08
Subtask 03-50-01-558-002-A01 Jun 01/08
TASK 03-50-01-558-803-A01 Nov 01/08
Subtask 03-50-01-558-003-A01 Jun 01/08
TASK 03-50-01-558-804-A01 Nov 01/08
Subtask 03-50-01-558-004-A01 Nov 01/08
TASK 03-50-01-558-805-A01 Nov 01/08
Subtask 03-50-01-558-005-A01 Jun 01/08
TASK 03-50-01-558-806-A01 Nov 01/08
Subtask 03-50-01-558-006-A01 Nov 01/08
TASK 03-50-01-558-807-A01 Nov 01/08
L.E.C.Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
Subtask 03-50-01-558-007-A01 Jun 01/08
TASK 03-50-01-558-808-A01 Nov 01/08
Subtask 03-50-01-558-008-A01 Jun 01/08
TASK 03-50-01-558-809-A01 R Jul 01/09
Subtask 03-50-01-558-009-A01 Nov 01/08
TASK 03-50-01-558-810-A01 Nov 01/08
Subtask 03-50-01-558-010-A01 Nov 01/08
TASK 03-50-01-558-810-B01 Nov 01/08
Subtask 03-50-01-558-012-A01 Nov 01/08
TASK 03-50-01-558-810-C01 Nov 01/08
Subtask 03-50-01-558-013-A01 Nov 01/08
TASK 03-50-01-558-810-D01 Nov 01/08
Subtask 03-50-01-558-014-A01 Nov 01/08
TASK 03-50-01-558-811-A01 R Jul 01/09
Subtask 03-50-01-558-011-A01 Nov 01/08
TASK 03-50-01-558-811-B01 R Jul 01/09
Subtask 03-50-01-558-015-A01 Nov 01/08
TASK 03-50-01-558-811-C01 R Jul 01/09
Subtask 03-50-01-558-016-A01 Nov 01/08
Subject 03-60-01
DESC 03-60-01-001-A01 R Jul 01/09
CHAPTER 04
Subject 04-00-00
DESC 04-00-00-001-A01 Jun 01/08
Subject 04-20-00
TASK 04-20-00-588-801-A01 R Jul 01/09
Subtask 04-20-00-588-001-A01 R Jul 01/09
FIGURE 04-20-00-991-001-A01 N Jul 01/09
L.E.C.Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 04-20-00-991-001-B01 N Jul 01/09
FIGURE 04-20-00-991-001-C01 N Jul 01/09
FIGURE 04-20-00-991-001-D01 N Jul 01/09
Subject 04-30-00
DESC 04-30-00-001-A01 Nov 01/08
FIGURE 04-30-00-991-001-A01 Jun 01/08
FIGURE 04-30-00-991-002-A01 Jun 01/08
FIGURE 04-30-00-991-002-B01 Jun 01/08
FIGURE 04-30-00-991-002-C01 Jun 01/08
FIGURE 04-30-00-991-002-D01 Jun 01/08
FIGURE 04-30-00-991-003-A01 Jun 01/08
TASK 04-30-00-556-801-A01 Nov 01/08
Subtask 04-30-00-556-001-A01 Nov 01/08
Subtask 04-30-00-556-002-A01 Jun 01/08
FIGURE 04-30-00-991-004-A01 Jun 01/08
FIGURE 04-30-00-991-005-A01 Jun 01/08
FIGURE 04-30-00-991-006-A01 Jun 01/08
FIGURE 04-30-00-991-007-A01 Jun 01/08
Subject 04-40-00
DESC 04-40-00-001-A01 Jun 01/08
Subject 04-50-00
DESC 04-50-00-001-A01 Jun 01/08
CHAPTER 05
Subject 05-00-00
DESC 05-00-00-001-A01 Nov 01/08
Subject 05-10-00
DESC 05-10-00-001-A01 Nov 01/08
FIGURE 05-10-00-991-004-A01 Nov 01/08
Subject 05-20-00
L.E.C.Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
DESC 05-20-00-001-A01 Nov 01/08
DESC 05-20-00-002-A01 Nov 01/08
FIGURE 05-20-00-991-013-A01 Nov 01/08
FIGURE 05-20-00-991-013-B01 Nov 01/08
FIGURE 05-20-00-991-001-A01 Nov 01/08
FIGURE 05-20-00-991-001-B01 Nov 01/08
FIGURE 05-20-00-991-002-A01 Nov 01/08
FIGURE 05-20-00-991-002-B01 Nov 01/08
DESC 05-20-00-004-A01 Nov 01/08
FIGURE 05-20-00-991-014-A01 Nov 01/08
FIGURE 05-20-00-991-015-A01 Nov 01/08
Subject 05-30-00
TASK 05-30-00-650-801-A01 Nov 01/08
Subtask 05-30-00-869-001-A01 Nov 01/08
Subtask 05-30-00-650-003-A01 Nov 01/08
Subject 05-40-00
DESC 05-40-00-001-A01 Nov 01/08
Subject 05-40-01
TASK 05-40-01-650-801-A01 Nov 01/08
Subtask 05-40-01-869-001-A01 Nov 01/08
Subtask 05-40-01-650-003-A01 Nov 01/08
Subject 05-40-02
TASK 05-40-02-650-801-A01 R Jul 01/09
Subtask 05-40-02-869-001-A01 Nov 01/08
Subtask 05-40-02-650-002-A01 Nov 01/08
FIGURE 05-40-02-991-004-A01 Nov 01/08
Subject 05-40-03
TASK 05-40-03-650-802-A01 Nov 01/08
Subtask 05-40-03-869-001-A01 Nov 01/08
L.E.C.Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
Subtask 05-40-03-010-001-A01 Nov 01/08
Subtask 05-40-03-010-001-B01 Nov 01/08
Subtask 05-40-03-650-002-A01 Nov 01/08
FIGURE 05-40-03-991-001-A01 Nov 01/08
Subject 05-50-00
DESC 05-50-00-005-A01 Nov 01/08
Subject 05-50-01
DESC 05-50-01-005-A01 Nov 01/08
Subject 05-60-00
DESC 05-60-00-001-A01 Nov 01/08
CHAPTER 06
Subject 06-00-00
DESC 06-00-00-001-A01 Jun 01/08
DESC 06-00-00-002-A01 N Jul 01/09
FIGURE 06-00-00-991-001-A01 N Jul 01/09
FIGURE 06-00-00-991-001-B01 N Jul 01/09
FIGURE 06-00-00-991-001-C01 N Jul 01/09
Subject 06-10-00
TASK 06-10-00-970-801-A01 R Jul 01/09
Subtask 06-10-00-970-001-A01 Nov 01/08
Subtask 06-10-00-869-001-A01 Jun 01/08
FIGURE 06-10-00-991-001-A01 Nov 01/08
FIGURE 06-10-00-991-002-A01 Jun 01/08
TASK 06-10-00-970-802-A01 Nov 01/08
Subtask 06-10-00-970-002-A01 Jun 01/08
TASK 06-10-00-970-803-A01 R Jul 01/09
Subtask 06-10-00-970-003-A01 Nov 01/08
Subtask 06-10-00-970-004-A01 Nov 01/08
FIGURE 06-10-00-991-003-A01 Jun 01/08
L.E.C.Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 06-10-00-991-004-A01 Jun 01/08
Subject 06-30-00
DESC 06-30-00-001-A01 R Jul 01/09
FIGURE 06-30-00-991-006-A01 Jun 01/08
FIGURE 06-30-00-991-010-A01 N Jul 01/09
DESC 06-30-00-001-B01 R Jul 01/09
FIGURE 06-30-00-991-007-A01 Jun 01/08
FIGURE 06-30-00-991-011-A01 N Jul 01/09
DESC 06-30-00-001-C01 R Jul 01/09
FIGURE 06-30-00-991-008-A01 Jun 01/08
FIGURE 06-30-00-991-012-A01 N Jul 01/09
DESC 06-30-00-001-D01 R Jul 01/09
FIGURE 06-30-00-991-009-A01 Jun 01/08
FIGURE 06-30-00-991-013-A01 N Jul 01/09
DESC 06-30-00-002-A01 Jun 01/08
TASK 06-30-00-581-802-A01 R Jul 01/09
Subtask 06-30-00-581-003-A01 R Jul 01/09
FIGURE 06-30-00-991-004-A01 Jun 01/08
TASK 06-30-00-581-801-A01 R Jul 01/09
Subtask 06-30-00-581-002-A01 R Jul 01/09
Subject 06-40-00
DESC 06-40-00-002-A01 R Jul 01/09
DESC 06-40-00-001-A01 N Jul 01/09
DESC 06-40-00-003-A01 N Jul 01/09
FIGURE 06-40-00-991-001-A01 N Jul 01/09
FIGURE 06-40-00-991-003-A01 N Jul 01/09
TASK 06-40-00-581-801-A01 R Jul 01/09
Subtask 06-40-00-581-001-A01 R Jul 01/09
Subject 06-50-00
L.E.C.Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
DESC 06-50-00-001-A01 Nov 01/08
FIGURE 06-50-00-991-020-A01 Nov 01/08
TASK 06-50-00-581-803-A01 R Jul 01/09
Subtask 06-50-00-581-002-A01 Nov 01/08
Subtask 06-50-00-581-003-A01 Nov 01/08
FIGURE 06-50-00-991-014-A01 Nov 01/08
FIGURE 06-50-00-991-015-A01 Jun 01/08
FIGURE 06-50-00-991-021-A01 Nov 01/08
TASK 06-50-00-581-802-A01 R Jul 01/09
Subtask 06-50-00-010-001-A01 Nov 01/08
Subtask 06-50-00-581-004-A01 Nov 01/08
Subtask 06-50-00-581-005-A01 Nov 01/08
FIGURE 06-50-00-991-013-A01 Jun 01/08
FIGURE 06-50-00-991-016-A01 Jun 01/08
FIGURE 06-50-00-991-017-A01 Nov 01/08
FIGURE 06-50-00-991-018-A01 Nov 01/08
TASK 06-50-00-581-801-A01 R Jul 01/09
Subtask 06-50-00-581-001-A01 R Jul 01/09
CHAPTER 07
Subject 07-00-00
DESC 07-00-00-002-A01 R Jul 01/09
Subject 07-20-00
DESC 07-20-00-001-A01 N Jul 01/09
FIGURE 07-20-00-991-001-A01 N Jul 01/09
Subject 07-40-00
DESC 07-40-00-001-A01 R Jul 01/09
Subject 07-40-01
TASK 07-40-01-584-801-A01 R Jul 01/09
Subtask 07-40-01-500-001-A01 Nov 01/08
L.E.C.Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
Subtask 07-40-01-500-002-A01 Nov 01/08
Subtask 07-40-01-869-001-A01 Jun 01/08
Subtask 07-40-01-584-001-A01 Jun 01/08
Subtask 07-40-01-869-002-A01 Jun 01/08
FIGURE 07-40-01-991-001-A01 Jun 01/08
FIGURE 07-40-01-991-002-A01 Jun 01/08
TASK 07-40-01-584-802-A01 Nov 01/08
Subtask 07-40-01-500-003-A01 Jun 01/08
Subtask 07-40-01-500-004-A01 Jun 01/08
Subtask 07-40-01-869-003-A01 Jun 01/08
Subtask 07-40-01-584-002-A01 Jun 01/08
Subtask 07-40-01-869-004-A01 Jun 01/08
Subject 07-40-02
TASK 07-40-02-584-801-A01 R Jul 01/09
Subtask 07-40-02-500-001-A01 Jun 01/08
Subtask 07-40-02-500-002-A01 Nov 01/08
Subtask 07-40-02-500-003-A01 Nov 01/08
Subtask 07-40-02-584-001-A01 Jun 01/08
Subtask 07-40-02-869-001-A01 Jun 01/08
FIGURE 07-40-02-991-001-A01 Jun 01/08
FIGURE 07-40-02-991-002-A01 Jun 01/08
FIGURE 07-40-02-991-003-A01 Jun 01/08
TASK 07-40-02-584-802-A01 R Jul 01/09
Subtask 07-40-02-500-004-A01 Jun 01/08
Subtask 07-40-02-020-001-A01 Nov 01/08
Subtask 07-40-02-500-006-A01 Nov 01/08
Subtask 07-40-02-584-002-A01 Jun 01/08
Subtask 07-40-02-869-002-A01 Jun 01/08
Subtask 07-40-02-500-007-A01 Nov 01/08
L.E.C.Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 07-40-02-991-004-A01 Jun 01/08
FIGURE 07-40-02-991-005-A01 Jun 01/08
FIGURE 07-40-02-991-006-A01 Jun 01/08
FIGURE 07-40-02-991-007-A01 Jun 01/08
Subject 07-40-03
TASK 07-40-03-584-801-A01 Nov 01/08
Subtask 07-40-03-584-001-A01 Jun 01/08
Subtask 07-40-03-584-002-A01 Jun 01/08
Subject 07-40-04
DESC 07-40-04-001-A01 Nov 01/08
FIGURE 07-40-04-991-001-A01 Jun 01/08
FIGURE 07-40-04-991-002-A01 Jun 01/08
FIGURE 07-40-04-991-003-A01 Jun 01/08
Subject 07-60-00
DESC 07-60-00-001-A01 Nov 01/08
Subject 07-60-01
DESC 07-60-01-001-A01 Nov 01/08
FIGURE 07-60-01-991-002-A01 Nov 01/08
FIGURE 07-60-01-991-003-A01 Nov 01/08
Subject 07-60-02
DESC 07-60-02-001-A01 R Jul 01/09
Subject 07-60-03
DESC 07-60-03-001-A01 Nov 01/08
CHAPTER 08
Subject 08-00-00
DESC 08-00-00-001-A01 Jun 01/08
CHAPTER 09
Subject 09-00-00
DESC 09-00-00-001-A01 Jun 01/08
L.E.C.Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
Subject 09-10-01
DESC 09-10-01-002-A01 Jun 01/08
DESC 09-10-01-001-A01 Jun 01/08
Subject 09-10-02
DESC 09-10-02-001-A01 Jun 01/08
DESC 09-10-02-003-A01 Jun 01/08
DESC 09-10-02-002-A01 Nov 01/08
FIGURE 09-10-02-991-001-A01 Jun 01/08
Subject 09-10-03
DESC 09-10-03-001-A01 Nov 01/08
FIGURE 09-10-03-991-001-A01 Jun 01/08
FIGURE 09-10-03-991-002-A01 Jun 01/08
DESC 09-10-03-001-B01 Nov 01/08
FIGURE 09-10-03-991-003-A01 Jun 01/08
FIGURE 09-10-03-991-004-A01 Jun 01/08
DESC 09-10-03-001-C01 Nov 01/08
FIGURE 09-10-03-991-005-A01 Jun 01/08
FIGURE 09-10-03-991-005-B01 Jun 01/08
FIGURE 09-10-03-991-006-A01 Jun 01/08
DESC 09-10-03-001-D01 Nov 01/08
FIGURE 09-10-03-991-007-A01 Jun 01/08
FIGURE 09-10-03-991-008-A01 Jun 01/08
Subject 09-10-04
DESC 09-10-04-001-A01 Nov 01/08
FIGURE 09-10-04-991-001-A01 Jun 01/08
FIGURE 09-10-04-991-001-B01 Jun 01/08
FIGURE 09-10-04-991-001-C01 Jun 01/08
FIGURE 09-10-04-991-001-D01 Jun 01/08
Subject 09-10-05
L.E.C.Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
DESC 09-10-05-001-A01 Nov 01/08
FIGURE 09-10-05-991-001-A01 Jun 01/08
FIGURE 09-10-05-991-001-B01 Jun 01/08
FIGURE 09-10-05-991-001-C01 Jun 01/08
FIGURE 09-10-05-991-001-D01 Jun 01/08
Subject 09-10-06
DESC 09-10-06-001-A01 Jun 01/08
FIGURE 09-10-06-991-001-A01 Jun 01/08
FIGURE 09-10-06-991-001-B01 Jun 01/08
FIGURE 09-10-06-991-001-C01 Jun 01/08
FIGURE 09-10-06-991-001-D01 Jun 01/08
Subject 09-10-08
DESC 09-10-08-001-A01 Nov 01/08
FIGURE 09-10-08-991-001-A01 Jun 01/08
FIGURE 09-10-08-991-001-B01 Jun 01/08
Subject 09-10-09
DESC 09-10-09-001-A01 Nov 01/08
FIGURE 09-10-09-991-001-A01 Jun 01/08
Subject 09-10-10
DESC 09-10-10-001-A01 Jun 01/08
DESC 09-10-10-002-A01 Nov 01/08
FIGURE 09-10-10-991-001-A01 Jun 01/08
FIGURE 09-10-10-991-001-B01 Jun 01/08
FIGURE 09-10-10-991-001-C01 Jun 01/08
FIGURE 09-10-10-991-001-D01 Jun 01/08
FIGURE 09-10-10-991-002-A01 Jun 01/08
FIGURE 09-10-10-991-003-A01 Jun 01/08
FIGURE 09-10-10-991-003-B01 Jun 01/08
FIGURE 09-10-10-991-003-C01 Jun 01/08
L.E.C.Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 09-10-10-991-003-D01 Jun 01/08
FIGURE 09-10-10-991-004-A01 Jun 01/08
DESC 09-10-10-003-A01 Nov 01/08
FIGURE 09-10-10-991-006-A01 Jun 01/08
FIGURE 09-10-10-991-006-B01 Jun 01/08
FIGURE 09-10-10-991-006-C01 Jun 01/08
FIGURE 09-10-10-991-006-D01 Jun 01/08
DESC 09-10-10-004-A01 Nov 01/08
FIGURE 09-10-10-991-010-A01 Jun 01/08
DESC 09-10-10-005-A01 Nov 01/08
FIGURE 09-10-10-991-011-A01 Jun 01/08
FIGURE 09-10-10-991-011-B01 Jun 01/08
FIGURE 09-10-10-991-011-C01 Nov 01/08
FIGURE 09-10-10-991-011-D01 Jun 01/08
DESC 09-10-10-006-A01 Nov 01/08
FIGURE 09-10-10-991-014-A01 Jun 01/08
Subject 09-10-11
DESC 09-10-11-001-A01 Nov 01/08
FIGURE 09-10-11-991-001-A01 Jun 01/08
FIGURE 09-10-11-991-002-A01 Jun 01/08
FIGURE 09-10-11-991-003-A01 Jun 01/08
FIGURE 09-10-11-991-004-A01 Jun 01/08
FIGURE 09-10-11-991-005-A01 Jun 01/08
FIGURE 09-10-11-991-006-A01 Jun 01/08
FIGURE 09-10-11-991-007-A01 Jun 01/08
DESC 09-10-11-001-B01 Nov 01/08
FIGURE 09-10-11-991-014-A01 Jun 01/08
FIGURE 09-10-11-991-015-A01 Jun 01/08
FIGURE 09-10-11-991-016-A01 Jun 01/08
L.E.C.Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 09-10-11-991-017-A01 Jun 01/08
FIGURE 09-10-11-991-018-A01 Jun 01/08
FIGURE 09-10-11-991-019-A01 Jun 01/08
FIGURE 09-10-11-991-020-A01 Jun 01/08
DESC 09-10-11-001-C01 Nov 01/08
FIGURE 09-10-11-991-021-A01 Jun 01/08
FIGURE 09-10-11-991-022-A01 Jun 01/08
FIGURE 09-10-11-991-023-A01 Jun 01/08
FIGURE 09-10-11-991-024-A01 Jun 01/08
FIGURE 09-10-11-991-025-A01 Jun 01/08
FIGURE 09-10-11-991-026-A01 Jun 01/08
FIGURE 09-10-11-991-027-A01 Jun 01/08
DESC 09-10-11-001-D01 Nov 01/08
FIGURE 09-10-11-991-028-A01 Jun 01/08
FIGURE 09-10-11-991-029-A01 Jun 01/08
FIGURE 09-10-11-991-030-A01 Jun 01/08
FIGURE 09-10-11-991-031-A01 Jun 01/08
FIGURE 09-10-11-991-032-A01 Jun 01/08
FIGURE 09-10-11-991-033-A01 Jun 01/08
FIGURE 09-10-11-991-034-A01 Jun 01/08
Subject 09-10-12
DESC 09-10-12-001-A01 Nov 01/08
FIGURE 09-10-12-991-001-A01 Jun 01/08
FIGURE 09-10-12-991-001-B01 Jun 01/08
FIGURE 09-10-12-991-001-C01 Jun 01/08
FIGURE 09-10-12-991-001-D01 Jun 01/08
DESC 09-10-12-002-A01 Jun 01/08
FIGURE 09-10-12-991-002-A01 Jun 01/08
FIGURE 09-10-12-991-003-A01 Jun 01/08
L.E.C.Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 09-10-12-991-014-A01 Jun 01/08
DESC 09-10-12-003-A01 Jun 01/08
FIGURE 09-10-12-991-004-A01 Jun 01/08
DESC 09-10-12-004-A01 Jun 01/08
FIGURE 09-10-12-991-008-A01 Nov 01/08
FIGURE 09-10-12-991-009-A01 Jun 01/08
FIGURE 09-10-12-991-015-A01 Jun 01/08
DESC 09-10-12-005-A01 Jun 01/08
FIGURE 09-10-12-991-010-A01 Jun 01/08
DESC 09-10-12-006-A01 Jun 01/08
FIGURE 09-10-12-991-013-A01 Jun 01/08
FIGURE 09-10-12-991-013-B01 Jun 01/08
Subject 09-10-13
DESC 09-10-13-001-A01 Jun 01/08
FIGURE 09-10-13-991-001-A01 Jun 01/08
Subject 09-10-14
DESC 09-10-14-001-A01 Nov 01/08
FIGURE 09-10-14-991-007-A01 Nov 01/08
FIGURE 09-10-14-991-008-A01 Nov 01/08
FIGURE 09-10-14-991-009-A01 Nov 01/08
DESC 09-10-14-001-B01 Nov 01/08
FIGURE 09-10-14-991-010-A01 Nov 01/08
FIGURE 09-10-14-991-011-A01 Nov 01/08
DESC 09-10-14-001-C01 Nov 01/08
FIGURE 09-10-14-991-013-A01 Nov 01/08
FIGURE 09-10-14-991-014-A01 Nov 01/08
FIGURE 09-10-14-991-015-A01 Nov 01/08
DESC 09-10-14-001-D01 Nov 01/08
FIGURE 09-10-14-991-016-A01 Nov 01/08
L.E.C.Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 09-10-14-991-017-A01 Nov 01/08
FIGURE 09-10-14-991-018-A01 Nov 01/08
Subject 09-10-15
DESC 09-10-15-001-A01 Nov 01/08
FIGURE 09-10-15-991-001-A01 Jun 01/08
FIGURE 09-10-15-991-001-B01 Jun 01/08
FIGURE 09-10-15-991-001-C01 Jun 01/08
FIGURE 09-10-15-991-001-D01 Jun 01/08
Subject 09-10-16
DESC 09-10-16-001-A01 Nov 01/08
FIGURE 09-10-16-991-001-A01 Jun 01/08
FIGURE 09-10-16-991-001-B01 Jun 01/08
FIGURE 09-10-16-991-001-C01 Jun 01/08
FIGURE 09-10-16-991-001-D01 Jun 01/08
FIGURE 09-10-16-991-002-A01 Jun 01/08
FIGURE 09-10-16-991-003-A01 Jun 01/08
FIGURE 09-10-16-991-004-A01 Jun 01/08
Subject 09-20-01
DESC 09-20-01-001-A01 Jun 01/08
DESC 09-20-01-002-A01 R Jul 01/09
FIGURE 09-20-01-991-001-A01 Jun 01/08
FIGURE 09-20-01-991-002-A01 Jun 01/08
FIGURE 09-20-01-991-003-A01 Jun 01/08
FIGURE 09-20-01-991-004-A01 Jun 01/08
FIGURE 09-20-01-991-005-A01 Jun 01/08
FIGURE 09-20-01-991-006-A01 R Jul 01/09
FIGURE 09-20-01-991-007-A01 Jun 01/08
FIGURE 09-20-01-991-008-A01 R Jul 01/09
FIGURE 09-20-01-991-009-A01 Jun 01/08
L.E.C.Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 09-20-01-991-010-A01 R Jul 01/09
FIGURE 09-20-01-991-011-A01 Jun 01/08
FIGURE 09-20-01-991-012-A01 R Jul 01/09
FIGURE 09-20-01-991-013-A01 Jun 01/08
FIGURE 09-20-01-991-014-A01 Jun 01/08
FIGURE 09-20-01-991-015-A01 R Jul 01/09
FIGURE 09-20-01-991-016-A01 D Jul 01/09
DESC 09-20-01-004-A01 Jun 01/08
DESC 09-20-01-005-A01 Jun 01/08
FIGURE 09-20-01-991-020-A01 Jun 01/08
TASK 09-20-01-869-801-A01 Jun 01/08
Subtask 09-20-01-869-001-A01 Jun 01/08
Subtask 09-20-01-869-002-A01 Jun 01/08
Subject 09-20-02
DESC 09-20-02-001-A01 Jun 01/08
Subject 09-30-01
DESC 09-30-01-001-A01 Jun 01/08
DESC 09-30-01-002-A01 Nov 01/08
Subject 09-30-02
DESC 09-30-02-001-A01 Nov 01/08
Subject 09-30-03
DESC 09-30-03-001-A01 Nov 01/08
DESC 09-30-03-002-A01 Nov 01/08
Subject 09-50-01
DESC 09-50-01-001-A01 Nov 01/08
FIGURE 09-50-01-991-001-A01 Jun 01/08
FIGURE 09-50-01-991-002-A01 Jun 01/08
FIGURE 09-50-01-991-003-A01 Jun 01/08
FIGURE 09-50-01-991-004-A01 Jun 01/08
L.E.C.Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CONTENT CHGCODE
LAST REVISIONDATE
FIGURE 09-50-01-991-005-A01 Jun 01/08
FIGURE 09-50-01-991-006-A01 Jun 01/08
FIGURE 09-50-01-991-007-A01 R Jul 01/09
FIGURE 09-50-01-991-008-A01 Jun 01/08
FIGURE 09-50-01-991-009-A01 Jun 01/08
FIGURE 09-50-01-991-010-A01 Jun 01/08
FIGURE 09-50-01-991-011-A01 Jun 01/08
FIGURE 09-50-01-991-012-A01 Jun 01/08
FIGURE 09-50-01-991-013-A01 Jun 01/08
FIGURE 09-50-01-991-014-A01 Jun 01/08
L.E.C.Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
TABLE OF CONTENTS
01 INTRODUCTION
01-00-00 INTRODUCTION01-00-00-001-A01 General01-00-00-002-A01 Important Notice to Users of this Document
01-00-02 SEQUENCE OF THE DOCUMENT
01-00-02-001-A01 General01-00-02-002-A01 Task Oriented ARM01-00-02-003-A01 Content01-00-02-004-A01 Effectivity Management
01-00-03 DEFINITIONS01-00-03-001-A01 General
01-10-01 RELATED DATA01-10-01-002-A01 Airbus Data01-10-01-001-A01 Other Data
01-20-01 GENERAL AIRCRAFT CHARACTERISTICS01-20-01-001-A01 General Aircraft Description
01-20-01-002-A01 General Aircraft Data01-20-01-002-B01 General Aircraft Data01-20-01-002-C01 General Aircraft Data01-20-01-002-D01 General Aircraft Data
02 SURVEY
02-00-00 SURVEY02-00-00-001-A01 General
02-10-01 CHARTS AND GUIDES02-10-01-001-A01 Aircraft Recovery Process
02-10-01-002-A01 Aircraft Recovery Logic Chart
02-20-01 INITIAL AIRCRAFT SURVEY02-20-01-285-801-A01 Initial Aircraft Survey
T.O.C.Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
02-20-02 INITIAL SITE SURVEY02-20-02-285-801-A01 Initial Site Survey
02-30-01 LANDING GEAR02-30-01-200-801-A01 Landing Gear Survey
02-30-01-481-801-A01 Installation of the Safety Device on Landing Gears
02-30-01-867-802-A01 Jacking for Wheel Change
02-40-01 HEALTH AND SAFETY ISSUES02-40-01-001-A01 General
03 WEIGHT AND CG MANAGEMENT
03-00-00 WEIGHT AND CG MANAGEMENT03-00-00-558-801-A01 General
03-20-01 FUEL LOAD AND CG CONTROL03-20-01-001-A01 General03-20-01-002-A01 Tables
03-20-02 MANUAL FUEL QUANTITY INDICATION
03-20-02-970-801-A01 Use of Magnetic Level Indicators (MLI)
03-50-01 MANAGING AIRCRAFT WEIGHT AND CG03-50-01-001-A01 Introduction03-50-01-558-801-A01 Cargo and Baggage Remaining Effect
03-50-01-558-801-B01 Cargo and Baggage Remaining Effect
03-50-01-558-801-C01 Cargo and Baggage Remaining Effect
03-50-01-558-801-D01 Cargo and Baggage Remaining Effect
03-50-01-558-802-A01 Total Traffic Load Remaining Effect
03-50-01-558-803-A01 Ballast Added Effect03-50-01-558-804-A01 Waste Water Remaining Effect
03-50-01-558-805-A01 Non OEW Catering Equipment Added Effect
03-50-01-558-806-A01 Potable Water Removed Effect03-50-01-558-807-A01 Cockpit and Cabin Crew Removed Effect
03-50-01-558-808-A01 Catering Equipment Removed Effect
03-50-01-558-809-A01 Hydraulic Fluid Removed Effect
03-50-01-558-810-A01 Large Components Removed / Missing
03-50-01-558-810-B01 Large Components Removed / Missing
T.O.C.Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
03-50-01-558-810-C01 Large Components Removed / Missing
03-50-01-558-810-D01 Large Components Removed / Missing
03-50-01-558-811-A01 Large Components Movement Effect
03-50-01-558-811-B01 Large Components Movement Effect
03-50-01-558-811-C01 Large Components Movement Effect
03-60-01 REFERENCE FOR CALCULATION03-60-01-001-A01 Information Required and Source Data
04 PREPARATION
04-00-00 PREPARATION04-00-00-001-A01 General
04-20-00 STABILIZING THE AIRCRAFT04-20-00-588-801-A01 Stabilizing the Aircraft
04-30-00 TETHERING THE AIRCRAFT04-30-00-001-A01 General04-30-00-556-801-A01 Mooring
04-40-00 GROUND ANCHORS04-40-00-001-A01 General
04-50-00 SOIL STABILITY04-50-00-001-A01 General
05 WEIGHT REDUCTION
05-00-00 WEIGHT REDUCTION05-00-00-001-A01 General
05-10-00 DEFUELING05-10-00-001-A01 General
05-20-00 FUEL SYSTEM DESCRIPTION05-20-00-001-A01 Fuel System Basic Description
05-20-00-002-A01 Tanks05-20-00-004-A01 Fuel Quantity Indicating System
T.O.C.Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-30-00 MOVING FUEL FOR CG CONTROL05-30-00-650-801-A01 Fuel Transfer
05-40-00 DEFUEL SCENARIOS05-40-00-001-A01 Defuel Scenarios
05-40-01 DEFUEL SCENARIO 1 NORMAL PRESSURE DEFUEL WITH ALLAIRCRAFT SYSTEMS SERVICEABLE
05-40-01-650-801-A01 Normal Pressure Defuel With All Aircraft Systems Serviceable
05-40-02 DEFUEL SCENARIO 2 DRAIN REMAINING FUEL05-40-02-650-801-A01 Drain Remaining Fuel
05-40-03 DEFUEL SCENARIO 3 DEFUEL USING AN EXTERNAL WIRINGHARNESS
05-40-03-650-802-A01 Defuel Using an External Wiring Harness
05-50-00 CARGO COMPARTMENTS05-50-00-005-A01 General
05-50-01 CARGO REMOVAL05-50-01-005-A01 Cargo Removal
05-60-00 REMOVAL OF LARGE COMPONENTS05-60-00-001-A01 General
06 LEVELING AND LIFTING
06-00-00 LEVELING AND LIFTING06-00-00-001-A01 General06-00-00-002-A01 Leveling/Lifting Obstructions
06-10-00 LOAD DETERMINATION06-10-00-970-801-A01 Vertical Loads Determination06-10-00-970-802-A01 Side loads on Jack Fittings
06-10-00-970-803-A01 Arc Movement Calculation
06-30-00 USE OF JACKS06-30-00-001-A01 General06-30-00-001-B01 General06-30-00-001-C01 General
T.O.C.Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
06-30-00-001-D01 General06-30-00-002-A01 Type of Jacks
06-30-00-581-802-A01 Jacking
06-30-00-581-801-A01 General Preparation and Instructions for Leveling and Lifting the Aircraftwith Jacks
06-40-00 USE OF PNEUMATIC LIFTING BAGS06-40-00-002-A01 General06-40-00-001-A01 Pneumatic Lifting Bags on Fuselage
06-40-00-003-A01 Pneumatic Lifting Bags on Wings
06-40-00-581-801-A01 General Preparation and Instructions for Leveling and Lifting the Aircraftwith Pneumatic Lifting Bags
06-50-00 USE OF CRANES06-50-00-001-A01 General06-50-00-581-803-A01 Forward Fuselage Crane Lifting
06-50-00-581-802-A01 Wing Rib Attachment Tool
06-50-00-581-801-A01 General Preparation and Instructions for Leveling and Lifting the Aircraftwith Cranes
07 MOVING THE AIRCRAFT
07-00-00 MOVING THE AIRCRAFT07-00-00-002-A01 General Preparation
07-20-00 PREPARING A ROADWAY07-20-00-001-A01 General
07-40-00 TOWING AND DEBOGGING07-40-00-001-A01 General
07-40-01 TOWING FROM THE NOSE LANDING GEAR07-40-01-584-801-A01 Towing on the NLG with a Towbar
07-40-01-584-802-A01 Towing on the NLG with a Towbarless Tractor
07-40-02 TOWING FROM THE MAIN LANDING GEAR07-40-02-584-801-A01 Towing with the Main Gear from the Front
07-40-02-584-802-A01 Towing with the Main Gear from the Rear
07-40-03 TOWING WITH DEFLATED TIRES
T.O.C.Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-40-03-584-801-A01 Towing with Deflated Tires
07-40-04 TOWING LOAD LIMITS07-40-04-001-A01 Load and Angle Limits
07-60-00 MOVING DAMAGED AIRCRAFT07-60-00-001-A01 General
07-60-01 MOVING DAMAGED AIRCRAFT ON TRAILERS07-60-01-001-A01 Moving Damaged Aircraft on Trailers
07-60-02 MOVING DAMAGED AIRCRAFT WITH CRANES07-60-02-001-A01 Moving Damaged Aircraft with Cranes
07-60-03 MOVING DAMAGED AIRCRAFT WITH SPECIALIZED EQUIPMENT
07-60-03-001-A01 Moving Damaged Aircraft with Specialized Vehicles
08 POST RECOVERY CORRECTIVE ACTIONS
08-00-00 POST RECOVERY CORRECTIVE ACTIONS08-00-00-001-A01 General
09 APPENDIX
09-00-00 APPENDIX09-00-00-001-A01 Introduction
09-10-01 UNITS AND CONVERSIONS09-10-01-002-A01 Units of Measurements09-10-01-001-A01 Conversion Tables
09-10-02 GLOSSARY OF TERMS09-10-02-001-A01 Definition of Terms09-10-02-003-A01 Abbreviations09-10-02-002-A01 Aircraft Reference Axes
09-10-03 AIRCRAFT DIMENSIONS09-10-03-001-A01 General09-10-03-001-B01 General09-10-03-001-C01 General09-10-03-001-D01 General
T.O.C.Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-04 AIRCRAFT STRUCTURAL SECTIONS09-10-04-001-A01 General
09-10-05 COMPOSITE MATERIALS09-10-05-001-A01 General
09-10-06 FUSELAGE FRAMES AND H-ARM TABLE09-10-06-001-A01 General
09-10-08 WING RIBS AND STATIONS09-10-08-001-A01 Wing Ribs and Stations
09-10-09 HORIZONTAL STABILIZERS RIBS AND STATIONS09-10-09-001-A01 General
09-10-10 DOOR SIZES AND LOCATIONS09-10-10-001-A01 General09-10-10-002-A01 Passenger/Crew Doors and Emergency Exit Doors
09-10-10-003-A01 Cargo Compartment Doors
09-10-10-004-A01 Nose Landing Gear Doors
09-10-10-005-A01 Main Landing-Gear Doors
09-10-10-006-A01 APU Doors
09-10-11 AIRCRAFT GROUND CLEARANCES09-10-11-001-A01 General09-10-11-001-B01 General09-10-11-001-C01 General09-10-11-001-D01 General
09-10-12 AIRCRAFT GROUND SERVICE CONNECTIONS09-10-12-001-A01 General09-10-12-002-A01 Hydraulic System
09-10-12-003-A01 Electrical System
09-10-12-004-A01 Fuel System
09-10-12-005-A01 Potable Water System
09-10-12-006-A01 Waste Water Disposal-System
09-10-13 AIRCRAFT GROUNDING POINTS09-10-13-001-A01 General
T.O.C.Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-14 CARGO COMPARTMENTS09-10-14-001-A01 General09-10-14-001-B01 General09-10-14-001-C01 General09-10-14-001-D01 General
09-10-15 LOCATION OF HAZARDOUS MATERIALS09-10-15-001-A01 General
09-10-16 LANDING GEARS09-10-16-001-A01 General
09-20-01 QUICK REFERENCE DATA
09-20-01-001-A01 General09-20-01-002-A01 Aircraft Recovery Logic Chart
09-20-01-004-A01 Airline Aircraft Recovery Process Document
09-20-01-005-A01 Off Runway Incident Reporting Proforma
09-20-01-869-801-A01 IATA Aircraft Recovery Quick Reference Check List
09-20-02 RECOVERY TEAM09-20-02-001-A01 Composition of the Recovery Team
09-30-01 AIRCRAFT RECOVERY EQUIPMENT TOOLING AND MATERIALS
09-30-01-001-A01 General09-30-01-002-A01 Airbus Specific Recovery Tools
09-30-02 AIRCRAFT RECOVERY TOOLING09-30-02-001-A01 General
09-30-03 IATP AIRCRAFT RECOVERY KITS09-30-03-001-A01 General09-30-03-002-A01 Example of IATP Recovery Kit
09-50-01 WEIGHT AND CG CALCULATION WORKSHEETS09-50-01-001-A01 Worksheets
T.O.C.Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
INTRODUCTION
01-00-00 INTRODUCTION
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-00-00-001-A01
General
1. This document is intended to provide, for areas which are under Airbus responsibility, aircraftcomprehensive details relative to the procedures, planning, equipment and tooling to effectivelyrecover the A318, A319, A320 or A321 aircraft. The airlines and airport authorities can use thisinformation as a planning tool for aircraft recovery preparations.Aircraft recovery is an operation that is the result of an unplanned incident and as such, advancepreparations should be made. These preparations should include the establishment of an AircraftRecovery Team, aircraft recovery training, listings of aircraft recovery equipment availability and thedevelopment of an internal Aircraft Recovery Process Document.These are general procedures and will vary according to the individual incident and the equipmentavailable. In most cases the recovery will be carried out under abnormal conditions of both weatherand aircraft attitude.Country and state rules and regulations have to be followed, even though they may impede therecovery operation. Make sure that the relevant authorities have formally released the aircraft, beforestarting the aircraft recovery process. For further information on aircraft accident and incidentinvestigation see ICAO Annex 13.Personal safety and prevention of secondary damage are emphasized in this document.The data provided in this document is based on a serviceable aircraft in a normal attitude (exceptwhere specified). If the aircraft is in a different condition, the data will have to be adjustedaccordingly.Procedures for aircraft recovery from water are not covered by this document.It is recommended that the individual airlines share their aircraft recovery experiences with theaircraft manufacturer and groups such as the International Airline Transport Association (IATA),Aircraft Recovery Task Force (ARTF) and the International Airline Technical Pool (IATP). TheInternational Airline Technical Pool as well as some airports and airlines could provide AircraftRecovery Kits, at strategic locations around the world. Information about these groups is available atthe following web sites:- http://www.iata.org- http://www.iatp.com
NOTE : IATP website and recovery kits are available for IATP members only.
NOTE : This chapter gives references to web sites for information only. Airbus shall not be heldliable for web site or document content and for update or change of addresses.
01-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-00-00-002-A01
Important Notice to Users of this Document
1. GeneralThe technical data contained in this Aircraft Recovery Manual (ARM) is intended only for generalplanning, preparations and establishing procedures for the recovery of a disabled A318, A319, A320or A321 aircraft with consideration given for return to service.Airbus recommends that A318, A319, A320 or A321 operators and airport authorities use the data inthis manual to develop recovery schemes based on various scenarios, using the equipment available,typical situations and the recommendations included in the ATA specification.Airbus strongly recommends that all data and actions related to the recovery are recorded to ensurethat all necessary corrective actions are taken prior to release to service of the aircraft.The data given in this document is accurate at the date of publication. In case of any conflict, theAircraft Technical Specification shall take precedence.This manual does not include data with regards to any optional modifications. These additions mayhave an impact on the weight and CG position calculations, defueling and cargo loading procedures.Contact Airbus for further information.
2. DisclaimerTHE USER HEREBY WAIVES, RELEASES AND RENOUNCES ALL WARRANTIES,OBLIGATIONS AND LIABILITIES OF AIRBUS AND RIGHTS, CLAIMS AND REMEDIES OF THEUSER AGAINST AIRBUS, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITHRESPECT TO ANY NON-CONFORMITY OR DEFECT IN THIS DOCUMENT, INCLUDING BUTNOT LIMITED TO:- ANY WARRANTY AGAINST HIDDEN DEFECTS;- ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS;- ANY IMPLIED WARRANTY ARISING FROM COURSE OF PERFORMANCE, COURSE OF
DEALING OR USAGE OF TRADE;- ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY, WHETHER CONTRACTUAL
OR DELICTUAL AND WHETHER OR NOT ARISING FROM AIRBUS’S NEGLIGENCE,ACTUAL OR IMPUTED, AND
- ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY FOR LOSS OR DAMAGE TOPROPERTY.
AIRBUS SHALL HAVE NO OBLIGATION OR LIABILITY, HOWSOEVER ARISING, FOR LOSS OFUSE, REVENUE OR PROFIT OR FOR ANY OTHER DIRECT, INCIDENTAL ORCONSEQUENTIAL DAMAGES WITH RESPECT TO ANY NON-CONFORMITY OR DEFECT INTHIS DOCUMENT.AIRBUS SHALL HAVE NO OBLIGATION OR LIABILITY WITH RESPECT TO THE BEHAVIOROF TOOLING USED FOR THE RECOVERY OF THE AIRCRAFT.
01-00-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
01-00-02 SEQUENCE OF THE DOCUMENT
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-00-02-001-A01
General
1. This manual obeys the ATA iSpec 2200 specification format.
2. This document uses a three-part identification reference (XX-XX-XX), in which each pair of digitmeans : CHAPTER, SECTION and SUBJECT.
3. The ARM contains two categories of data.
A. DescriptionThis part gives the general description of the aircraft or systems, data related to aircraftrecovery (recovery team, recovery charts, landing gear, fuel ...) and worksheets.For details about the numbering of the description topics, see FIGURE 01-00-02-991-001-A.
B. TaskFor details on the task oriented ARM, see DESC 01-00-02-002-A01.For details about the numbering of the tasks, see FIGURE 01-00-02-991-002-A.
4. Warnings, Cautions and Notes.- WARNING: Calls attention to use of materials, processes, methods, procedures or limits that
must be carefully obeyed to prevent injury or death.- CAUTION: Calls attention to methods and procedures that must be obeyed to prevent damage to
equipment.- NOTE: Calls attention to methods that make the work easier or gives explanations.
5. AbbreviationsAll the abbreviations used in this manual are detailed in 09-10-02.
6. Revision bars.The revision bars show that the content is either new or revised.
7. This manual recommends that the recovery team makes and issues records to help aircraft return toservice and carefully monitors the implementation of corrective actions.See 08-00-00.
01-00-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
PA
RT
1 T
HR
U 3
FU
NC
TIO
N
AT
A S
IX−
DIG
IT N
UM
BE
R F
RO
M T
HE
AT
A IS
PE
C 2
200
BR
EA
KD
OW
N D
OC
UM
EN
T
TH
AT
IDE
NT
IFIE
S T
HE
CH
AP
TE
R−
SE
CT
ION
−S
UB
JEC
T.
TH
RE
E−
DIG
IT N
UM
BE
R T
HA
T ID
EN
TIF
IES
TH
E D
ES
CR
IPT
ION
S.
4 5T
HR
EE
−D
IGIT
ALP
HA
NU
ME
RIC
AL
IDE
NT
IFIE
R T
HA
T ID
EN
TIF
IES
TH
E C
ON
FIG
UR
AT
ION
.
12
34
5
N_A
R_0
1000
2_1_
0010
101_
01_0
0
Numbering SystemDescription
FIGURE-01-00-02-991-001-A01
01-00-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
PA
RT
1 T
HR
U 3
FU
NC
TIO
N
AT
A S
IX−
DIG
IT N
UM
BE
R F
RO
M T
HE
AT
A IS
PE
C 2
200
BR
EA
KD
OW
N D
OC
UM
EN
T
TH
AT
IDE
NT
IFIE
S T
HE
CH
AP
TE
R−
SE
CT
ION
−S
UB
JEC
T.
TH
RE
E−
DIG
IT F
UN
CT
ION
CO
DE
TH
AT
YO
U C
AN
FIN
D IN
TH
E F
UN
CT
ION
CO
DE
LIS
T
TH
AT
IND
ICA
TE
S T
HE
SP
EC
IFIC
PR
OC
ED
UR
E R
ELA
TE
D T
O T
AS
KS
AN
D S
UB
TA
SK
S.
TH
RE
E−
DIG
IT N
UM
BE
R A
LLO
CA
TE
D T
O E
AC
H T
AS
K A
ND
SU
BT
AS
K.
TO
SE
PA
RA
TE
TH
E T
AS
KS
AN
D S
UB
TA
SK
S, T
HE
TA
SK
NU
MB
ER
S B
EG
IN A
T
801
AN
D IN
CR
EA
SE
, IN
SE
QU
EN
CE
, TO
999
(M
AX
IMU
M).
TH
E S
UB
TA
SK
NU
MB
ER
S B
EG
IN A
T 0
01 A
ND
INC
RE
AS
E
IN S
EQ
UE
NC
E T
O 8
00 (
MA
XIM
UM
) W
ITH
IN T
HE
PR
OC
ED
UR
E.
TH
RE
E−
DIG
IT A
LPH
AN
UM
ER
ICA
L ID
EN
TIF
IER
TH
AT
IDE
NT
IFIE
S T
HE
CO
NF
IGU
RA
TIO
N.
4 5 6
12
34
56
SE
E 0
1−00
−02
−00
2(
)
N_A
R_0
1000
2_1_
0020
101_
01_0
0
Numbering SystemTask
FIGURE-01-00-02-991-002-A01
01-00-02Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-00-02-002-A01
Task Oriented ARM
1. GeneralIn the ARM, the procedures are contained in tasks.The task is a logical sequence of the procedure steps and is broken down into subtasks.The subtask gives all the details of the significant steps of the procedure.For task numbering, see DESC 01-00-02-001-A01.
2. Function CodesEach task and subtask has a function code related to its subject.
FunctionCode
Definition Task/Subtask
000 Removal Task
010 Remove/Open For Access Task/Subtask
020 Remove Unit/Component/Disconnect/Loosen/Remove Item Task/Subtask
040 Deactivation Task/Subtask
081 Remove Safety Locks Task/Subtask
200 Inspection/Check Task
284 Inspection of damage Subtask
285 Survey Damage and Terrain Task/Subtask
481 Install Safety Locks Task/Subtask
500 Material and Aircraft Handling Task/Subtask
556 Mooring Task/Subtask
558 Weight and CG Management Task/Subtask
581 Leveling/Lifting Task/Subtask
582 Moving the Aircraft Task/Subtask
583 Shoring Task/Subtask
584 Towing Task/Subtask
585 Taxiing Task/Subtask
586 Lowering Task/Subtask
587 Debogging Task/Subtask
588 Stabilizing Task/Subtask
650 Fueling/Defueling Task/Subtask
680 Drain Fluid Task/Subtask
862 De-energize Electrical Network Task/Subtask
01-00-02Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
FunctionCode
Definition Task/Subtask
866 Flight Control Surfaces Movement Task/Subtask
867 Landing Gear Movement Task/Subtask
869 Miscellaneous Task/Subtask
970 Data Recording/Calculating Task/Subtask
972 Damage Recording Subtask
980 Manual Operation or Positioning Subtask
Task/Subtask Function Codes Definition
TABLE 1
3. Task StructureEach recovery task is broken down into the paragraphs that follow:
A. Task Supporting Data
(1) GeneralThis paragraph gives general information and a short description of the procedure.
(2) InspectionThis paragraph gives instructions to do a preliminary inspection if necessary.
(3) Job Set Up DataThis paragraph collects all the generic data which are not in the Job Set Up Informationand are necessary to do the actions described in the procedure.
(4) Job Set Up InformationThis paragraph collects all materials, tools and referenced information necessary to do theactions described in the procedure.
B. ProcedureThis paragraph is broken down into subtasks.
(1) SubtasksThe Subtasks contain actions/instructions to do the procedure.
C. FiguresThis part contains all illustrations related to the procedure.
01-00-02Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-00-02-003-A01
Content
1. MANUAL FRONT MATTERThis part of the manual contains the preliminary pages.Items in this part are:
A. The manual front page.
B. The highlights which give the description of changes at subtask and figure level.
C. The list of effective content which gives for each task, subtask and figure the last revision datewith a change code (which is also used in the highlights):- blank: no changes- R: revised content- N: new content- D: deleted content.
D. The table of contents which is the list of chapters, subjects, tasks and descriptions contained inthe manual.
2. Chapter 01 - INTRODUCTIONThis chapter gives general data and information on the A318, A319, A320 or A321 aircraft.Items in this chapter are:
A. A list of related documents in which it is possible to find more information.
B. A general aircraft description.
3. Chapter 02 - SURVEYThis chapter gives the information that follow for areas which are under Airbus responsibility:
A. An aircraft recovery logic chart, which has been developed for the Aircraft Recovery Managerand his team, to help obey the necessary steps of the recovery process. It is used with a specificCHAPTER/SECTION/SUBJECT of the ARM.
B. Details on initial inspection, site survey, soil stability, weather conditions and equipment.
C. Health and safety issues related to aircraft recovery.
4. Chapter 03 - WEIGHT AND CG MANAGEMENTThis chapter contains the items that follow:
A. Weight, H-arm, Y-arm and Z-arm management, with general and specific information foroperations such as calculation of the NRW, associated H-arm, Y-arm and Z-arm locations andCG.
B. The names of documents where it is possible to find aircraft weight and balance data.
C. The effect of different elements on the CG, such as large aircraft components, fuel, payload…
01-00-02Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Chapter 04 - PREPARATIONThis chapter contains the details that follow:
A. The tasks which are necessary before leveling/lifting the aircraft (manual operation of flightcontrol surfaces, tethering, ground anchoring, check of weight, H-arm and Y-arm, etc.).
B. The tethering procedure.
C. General information and instructions for the manual operation of different units or equipmentssuch as landing gears, flaps, flight controls, cargo doors…
6. Chapter 05 - WEIGHT REDUCTIONThis chapter gives:
A. Detailed information on the aircraft fuel system.
B. The way to manually find the fuel quantity.
C. Various defueling scenarios.
D. Detailed information on payload removal.
E. The removal procedure of the major components.
7. Chapter 06 - LEVELING AND LIFTINGThis chapter gives details on:
A. The basic means of leveling/lifting the aircraft.
(1) Jacks,
(2) Pneumatic Lifting Bags,
(3) Cranes.
B. The method to calculate expected load, travel range and arc movement based on aircraftattitude, NRW and CG calculated in Chapter 03.
C. Detailed leveling/lifting scenarios.
8. Chapter 07 - MOVING THE AIRCRAFTThis chapter gives:
A. Debogging or towing methods and aircraft limits.
B. Procedures to be implemented to return a damaged aircraft to the hard surface.
9. Chapter 08 - POST RECOVERY CORRECTIVE ACTIONSThis chapter gives:
A. A link to the post recovery AMM inspection.
B. An explanation about the need of recording and monitoring corrective actions during therecovery operation.
10. Chapter 09 - APPENDIXThe appendices give general information on:
A. Units and Measurements.
01-00-02Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
B. Glossary of terms and list of abbreviations.
C. General aircraft description.
D. Recovery preparation.
E. Tooling and equipment.
F. Calculation worksheets.
01-00-02Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-00-02-004-A01
Effectivity Management
1. The Aircraft Recovery Manual is issued to give the necessary data for A318, A319, A320 or A321aircraft which are necessary to accomplish a recovery.The configuration is managed at the aircraft level:- A318-100- A319-100- A320-100- A320-200- A321-100- A321-200
01-00-02Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
01-00-03 DEFINITIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-00-03-001-A01
General
1. Terms DefinitionsChapter DESC 09-10-02-001-A01 gives the definition of terms related to aircraft recovery.
2. Abbreviations DefinitionsChapter DESC 09-10-02-003-A01 gives the definitions of abbreviations related to aircraft recovery.
01-00-03Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
01-10-01 RELATED DATA
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-10-01-002-A01
Airbus Data
1. GeneralIf necessary, you can find additional information/data in the documents that follow:- A318, A319, A320 or A321 Aircraft Characteristics (AC)- A318, A319, A320 or A321 Aircraft Maintenance Manual (AMM)- A318/A319/A320/A321 Illustrated Parts Catalog (IPC)- A318, A319, A320 or A321 Structural Repair Manual (SRM)- A318, A319, A320 or A321 Maintenance Facility Planning Manual (MFP)- A318, A319, A320 or A321 Weight and Balance Manual (WBM)- A318/A319/A320/A321 Illustrated Tool and Equipment Manual (TEM)- A319/A320/A321 Cargo Loading System Manual (CLS)- List of Radioactive and Hazardous Elements Manual (LRE)- CFM56 Engine Manual- IAE V2500 Engine Manual (A319, A320 or A321 only)- PW 6000 Engine Manual (A318 only)- Airn@v, AirbusWorld, …
01-10-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-10-01-001-A01
Other Data
1. Web SitesThis topic gives references to web sites for information only. This list is not exhaustive and is madefrom the data available to Airbus at issue of the ARM.- http://www.iata.org- http://www.iatp.com
NOTE : IATP website and recovery kits are available for IATP members only.
NOTE : This chapter gives references to web sites for information only. Airbus shall not be heldliable for web site or document content and for update or change of addresses.
2. Publications - Manuals - DocumentsThis topic gives references to non-Airbus manuals or documents for information only. This list is notexhaustive and is made from the data available to Airbus at issue of the ARM. Airbus shall not beheld liable for document content.- Country Regulation- ICAO Annex 14- ICAO Annex 13- ICAO 9137 Part 5- FAA AC 150/5200-31A- FAR 139.325 Airport Emergency Plan- JAR/FAR 145
3. Airline DocumentsThis topic gives references to airline documents for information only. This list is not exhaustive.- Airline Aircraft Recovery Process Documents (see DESC 09-20-01-004-A01)- Airline Load and Trim Sheet Document- Airline Weight and Balance Manual- Airline Aircraft Modification Record
01-10-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
01-20-01 GENERAL AIRCRAFT CHARACTERISTICS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 01-20-01-001-A01
General Aircraft Description
1. The A320 Family of aircraft are subsonic single-aisle aircraft. These aircraft are suitable forpassengers and cargo commercial transport.They have two turbofan engines under the wings:- CFM 56-5 engine,- IAE V2500 engine (A319, A320 or A321)- PW 6000 engine (A318 only).The A320 Family aircraft have:- A standard configuration of 3 main fuel tanks (1 tank per wing and a center tank in the center
wing box). One or more Additional Center Tanks (ACT) can be installed in the cargocompartments, depending on the airline configuration.
- 1 standard 2.5 in refuel/defuel coupling under the wing and 1 gravity refuel cap on each wing(related to the aircraft configuration),
- 2 twin-wheel main landing gears (standard configuration) or 2 four-wheel bogies MLG (optional,on A320 only),
- 1 nose landing gear with two wheels,- 1 potable water tank in the pressurized section of the fuselage,- A waste water tank,- A lower deck forward cargo compartment,- A lower deck aft cargo compartment,- A lower deck bulk cargo compartment (related to the aircraft configuration).
2. The appendix gives detailed aircraft description.See 09-00-00.
01-20-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
DESC 01-20-01-002-A01
General Aircraft Data
1. This section gives general data (weight, payload, fuel capacity, ...) related to the A318-100 aircraft.Refer to the operator’s documentation for accurate values related to the specific aircraft.
Weight Variant WV000 WV001 WV002 WV003 WV004
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
59400 kg(130955 lb)
61900 kg(136466 lb)
63400 kg(139773 lb)
64900 kg(143080 lb)
66400 kg(146387 lb)
Maximum TakeoffWeight (MTOW)
59000 kg(130073 lb)
61500 kg(135584 lb)
63000 kg(138891 lb)
64500 kg(142198 lb)
66000 kg(145505 lb)
Maximum LandWeight (MLW)
56000 kg(123459 lb)
56000 kg(123459 lb)
57500 kg(126766 lb)
57500 kg(126766 lb)
57500 kg(126766 lb)
Maximum ZeroFuel Weight(MZFW)
53000 kg(116845 lb)
53000 kg(116845 lb)
54500 kg(120152 lb)
54500 kg(120152 lb)
54500 kg(120152 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 38818 kg (85579 lb)With PW Engines : 38661 kg (85233 lb)
Maximum Payloadwith CFM Engines
14182 kg(31266 lb)
15682 kg(34573 lb)
Maximum Payloadwith PW Engines
14339 kg(31612 lb)
15839 kg(34919 lb)
Accommodation Typical Single Class Layout : 136 Seats
23859 l (6303 US gal)Usable FuelCapacity(Density = 0.785kg/l)
18729 kg (41290 lb)
Volume of CargoCompartments
22.84 m3
(806.59 ft3)
Aircraft Data
TABLE 1
01-20-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV005 WV006 WV007 WV008
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
68400 kg(150796 lb)
56400 kg(124341 lb)
61400 kg(135364 lb)
64400 kg(141978 lb)
Maximum TakeoffWeight (MTOW)
68000 kg(149914 lb)
56000 kg(123459 lb)
61000 kg(134482 lb)
64000 kg(141096 lb)
Maximum LandWeight (MLW)
57500 kg(126766 lb)
56000 kg(123459 lb)
56000 kg(123459 lb)
56000 kg(123459 lb)
Maximum ZeroFuel Weight(MZFW)
54500 kg(120152 lb)
53000 kg(116845 lb)
53000 kg(116845 lb)
53000 kg(116845 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 38818 kg (85579 lb)With PW Engines : 38661 kg (85233 lb)
Maximum Payloadwith CFM Engines
15682 kg(34573 lb)
14182 kg(31266 lb)
Maximum Payloadwith PW Engines
15839 kg(34919 lb)
14339 kg(31612 lb)
Accommodation Typical Single Class Layout : 136 Seats
23859 l (6303 US gal)Usable FuelCapacity(Density = 0.785kg/l)
18729 kg (41290 lb)
Volume of CargoCompartments
22.84 m3
(806.59 ft3)
Aircraft Data
TABLE 2
01-20-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
DESC 01-20-01-002-B01
General Aircraft Data
1. This section gives general data (weight, payload, fuel capacity, ...) related to the A319-100 aircraft.Refer to the operator’s documentation for accurate values related to the specific aircraft.
Weight Variant WV000 WV001 WV002 WV003
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
64400 kg(141978 lb)
70400 kg(155205 lb)
75900 kg(167331 lb)
68400 kg(150796 lb)
Maximum TakeoffWeight (MTOW)
64000 kg(141096 lb)
70000 kg(154324 lb)
75500 kg(166449 lb)
68000 kg(149914 lb)
Maximum LandWeight(MLW)
61000 kg(134482 lb)
61000 kg(134482 lb)
62500 kg(137789 lb)
61000 kg(134482 lb)
Maximum Zero FuelWeight(MZFW)
57000 kg(125663 lb)
57000 kg(125663 lb)
58500 kg(128970 lb)
57000 kg(125663 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 39725 kg (87579 lb)With IAE Engines : 39826 kg (87801 lb)
Maximum Payloadwith CFM Engines
17275 kg(38085 lb)
18775 kg(41392 lb)
17275 kg(38085 lb)
Maximum Payloadwith IAE Engines
17174 kg(37862 lb)
18674 kg(41169 lb)
17174 kg(37862 lb)
Accommodation Typical Single Class Layout : 145 Seats
23859 l(6303 US gal)Usable Fuel Capacity
(Density = 0.785kg/l) 18729 kg
(41290 lb)
Volumeof CargoCompartments
27.66 m3
(976.80 ft3)
Aircraft Data
TABLE 1
01-20-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV004 WV005 WV006 WV007
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
68400 kg(150796 lb)
70400 kg(155205 lb)
73900 kg(162922 lb)
75900(167331 lb)
Maximum TakeoffWeight (MTOW)
68000 kg(149914 lb)
70000 kg(154324 lb)
73500 kg(162040 lb)
75500 kg(166449 lb)
Maximum LandWeight(MLW)
62500 kg(137789 lb)
62500 kg(137789 lb)
62500 kg(137789 lb)
61000 kg(134482 lb)
Maximum Zero FuelWeight (MZFW)
58500 kg(128970 lb)
58500 kg(128970 lb)
58500 kg(128970 lb)
57000 kg(125663 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 39725 kg (87579 lb)With IAE Engines : 39826 kg (87801 lb)
Maximum Payloadwith CFM Engines
18775 kg(41392 lb)
17275 kg(38085 lb)
Maximum Payloadwith IAE Engines
18674 kg(41169 lb)
17174 kg(37862 lb)
Accommodation Typical Single Class Layout : 145 Seats
23859 l(6303 US gal)Usable Fuel Capacity
(Density = 0.785kg/l) 18729 kg
(41290 lb)
Volumeof CargoCompartments
27.66 m3
(976.80 ft3)
Aircraft Data
TABLE 2
Weight Variant WV008 WV009 WV011 WV012
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
64400(141978 lb)
66400(141978 lb)
66400(141978 lb)
62400(137568 lb).
Maximum TakeoffWeight (MTOW)
64000 kg(141096 lb)
66000 kg(145505 lb)
66000 kg(145505 lb)
62000 kg(136687 lb)
01-20-01Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV008 WV009 WV011 WV012
Maximum LandWeight(MLW)
62500 kg(137789 lb)
62500 kg(137789 lb)
61000 kg(134482 lb)
61000 kg(134482 lb)
Maximum Zero FuelWeight (MZFW)
58500 kg(128970 lb)
58500 kg(128970 lb)
57000 kg(125663 lb)
57000 kg(125663 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 39725 kg (87579 lb)With IAE Engines : 39826 kg (87801 lb)
Maximum Payloadwith CFM Engines
18775 kg(41392 lb)
17275 kg(38085 lb)
Maximum Payloadwith IAE Engines
18674 kg(41169 lb)
17174 kg(37862 lb)
Accommodation Typical Single Class Layout : 145 Seats
23859 l(6303 US gal)Usable Fuel Capacity
(Density = 0.785kg/l) 18729 kg
(41290 lb)
Volumeof CargoCompartments
27.66 m3
(976.80 ft3)
Aircraft Data
TABLE 3
01-20-01Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
DESC 01-20-01-002-C01
General Aircraft Data
**ON A/C A320-100
1. This section gives general data (weight, payload, fuel capacity, ...) related to the A320-100 aircraft.Refer to the operator’s documentation for accurate values related to the specific aircraft.
Weight Variant WV000 WV001 WV002
Maximum Ramp Weight(MRW)Maximum Taxi Weight(MTW)
68400 kg(150796 lb)
66400 kg(146387 lb)
68400 kg(150796 lb)
Maximum Takeoff Weight(MTOW)
68000 kg(149914 lb)
66000 kg(145505 lb)
68000 kg(149914 lb)
Maximum Land Weight(MLW)
63000 kg (138891 lb)
Maximum Zero FuelWeight (MZFW)
59000 kg (130073 lb)
Operating Empty Weight(OEW) - Typical
With CFM Engines : 41244 kg (90927 lb)
Maximum Payloadwith CFM Engines
17756 kg(39145 lb)
18556 kg(40909 lb)
Accommodation Typical Single Class Layout : 180 Seats
23667 l (6252 US gal)Usable Fuel Capacity(Density = 0.785 kg/l) 18578 kg (40957 lb)
Volume of CargoCompartments
37.42 m3 (1321.47 ft3)
Aircraft Data
TABLE 1
**ON A/C A320-200
2. This section gives general data (weight, payload, fuel capacity, ...) related to the A320-200 aircraft.Refer to the operator’s documentation for accurate values related to the specific aircraft.
01-20-01Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV000 WV001 WV002 WV003
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
73900 kg(162922 lb)
68400 kg(150796 lb)
70400 kg(155205 lb)
75900 kg(167331 lb)
Maximum TakeoffWeight (MTOW)
73500 kg(162040 lb)
68000 kg(149914 lb)
70000 kg(154324 lb)
75500 kg(166449 lb)
Maximum LandWeight (MLW)
64500 kg (142198 lb)
Maximum ZeroFuel Weight(MZFW)
60500 kg (133380 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 42144 kg (92912 lb)With IAE Engines : 41345 kg (91150 lb)
Maximum Payloadwith CFM Engines
19256 kg(42452 lb)
Maximum Payloadwith IAE Engines
19155 kg(42230 lb)
Accommodation Typical Single Class Layout : 180 Seats
23859 l (6303 US gal)26759 l (7069 US gal) with 1 ACT - 29659 l (7835 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18729 kg (41290 lb)21005 kg (46308 lb) with 1 ACT - 23282 kg (51328 lb) with 2 ACT
Volume of CargoCompartments
37.42 m3 (1321.47 ft3)
Aircraft Data
TABLE 2
Weight Variant WV004 WV005 WV006 WV007
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
71900 kg(158512 lb)
67400 kg(148592 lb)
66400 kg(146387 lb)
77400 kg(170638 lb)
Maximum TakeoffWeight (MTOW)
71500 kg(157630 lb)
67000 kg(147710 lb)
66000 kg(145505 lb)
77000 kg(169756 lb)
Maximum LandWeight (MLW)
64500 kg (142198 lb)
01-20-01Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV004 WV005 WV006 WV007
Maximum ZeroFuel Weight(MZFW)
60500 kg (133380 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 42144 kg (92912 lb)With IAE Engines : 41345 kg (91150 lb)
Maximum Payloadwith CFM Engines
19256 kg(42452 lb)
19256 kg(42452 lb)
Maximum Payloadwith IAE Engines
19155 kg(42230 lb)
19155 kg(42230 lb)
Accommodation Typical Single Class Layout : 180 Seats
23859 l (6303 US gal)26759 l (7069 US gal) with 1 ACT - 29659 l (7835 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18729 kg (41290 lb)21005 kg (46308 lb) with 1 ACT - 23282 kg (51328 lb) with 2 ACT
Volume of CargoCompartments
37.42 m3 (1321.47 ft3)
Aircraft Data
TABLE 3
Weight Variant WV008 WV009 WV010 WV011
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
73900 kg(162922 lb)
75900 kg(167331 lb)
77400 kg(170638 lb)
75900 kg(167331 lb)
Maximum TakeoffWeight (MTOW)
73500 kg(162040 lb)
75500 kg(166449 lb)
77000 kg(169756 lb)
75500 kg(166449 lb)
Maximum LandWeight (MLW)
64500 kg(142198 lb)
66000 kg(145505 lb)
Maximum ZeroFuel Weight(MZFW)
61000 kg(134482 lb)
62500 kg(137789 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 42144 kg (92912 lb)With IAE Engines : 41345 kg (91150 lb)
Maximum Payloadwith CFM Engines
19756 kg(43555 lb)
21256 kg(46861 lb)
01-20-01Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV008 WV009 WV010 WV011
Maximum Payloadwith IAE Engines
19655 kg(43332 lb)
21155 kg(46639 lb)
Accommodation Typical Single Class Layout : 180 Seats
23859 l (6303 US gal)26759 l (7069 US gal) with 1 ACT - 29659 l (7835 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18729 kg (41290 lb)21005 kg (46308 lb) with 1 ACT - 23282 kg (51328 lb) with 2 ACT
Volume of CargoCompartments
37.42 m3 (1321.47 ft3)
Aircraft Data
TABLE 4
Weight Variant WV012 WV013 WV014 WV015 WV016
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
77400 kg(170638 lb)
71900 kg(158512 lb)
73900 kg(162922 lb)
78400 kg(172842 lb)
73900 kg(162922 lb)
Maximum TakeoffWeight (MTOW)
77000 kg(169756 lb)
71500 kg(157630 lb)
73500 kg(162040 lb)
78000 kg(171961 lb)
73500 kg(162040 lb)
Maximum LandWeight (MLW)
66000 kg(145505 lb)
64500 kg(142198 lb)
Maximum ZeroFuel Weight(MZFW)
62500 kg(137789 lb)
61000 kg(134482 lb)
61500 kg(135584 lb)
61000 kg(134482 lb)
62500 kg(137789 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 42144 kg (92912 lb)With IAE Engines : 41345 kg (91150 lb)
Maximum Payloadwith CFM Engines
21256 kg(46861 lb)
19756 kg(43555 lb)
20256 kg(44657 lb)
19756 kg(43555 lb)
21256 kg(46861 lb)
Maximum Payloadwith IAE Engines
21155 kg(46639 lb)
19655 kg(43332 lb)
20155 kg(44434 lb)
19655 kg(43332 lb)
21155 kg(46639 lb)
Accommodation Typical Single Class Layout : 180 Seats
23859 l (6303 US gal)26759 l (7069 US gal) with 1 ACT - 29659 l (7835 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18729 kg (41290 lb)21005 kg (46308 lb) with 1 ACT - 23282 kg (51328 lb) with 2 ACT
01-20-01Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV012 WV013 WV014 WV015 WV016
Volume of CargoCompartments
37.42 m3 (1321.47 ft3)
Aircraft Data
TABLE 5
01-20-01Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
DESC 01-20-01-002-D01
General Aircraft Data
**ON A/C A321-100
1. This section gives general data (weight, payload, fuel capacity, ...) related to the A321-100 aircraft.Refer to the operator’s documentation for accurate values related to the specific aircraft.
Weight Variant WV000 WV001 WV002 WV003 WV004
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
83400 kg(183865 lb)
85400 kg(188275 lb)
83400 kg(183865 lb)
85400 kg(188275 lb)
78400 kg(172842 lb)
Maximum TakeoffWeight (MTOW)
83000 kg(182984 lb)
85000 kg(187393 lb)
83000 kg(182984 lb)
85000 kg(187393 lb)
78000 kg(171961 lb)
Maximum LandWeight (MLW)
73500 kg(162040 lb)
73500 kg(162040 lb)
74500 kg(164244 lb)
74500 kg(164244 lb)
73500 kg(162040 lb)
Maximum ZeroFuel Weight(MZFW)
69500 kg(153221 lb)
69500 kg(153221 lb)
70500 kg(155426 lb)
70500 kg(155426 lb)
69500 kg(153221 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 46856 kg (103300 lb)With IAE Engines : 46959 kg (103527 lb)
Maximum Payloadwith CFM Engines
22644 kg(49921 lb) TBD
23644 kg(52126 lb)
22644 kg(49921 lb)
Maximum Payloadwith IAE Engines
22541 kg(49694 lb) TBD
23541 kg(51899 lb)
22541 kg(49694 lb)
Accommodation Typical Single Class Layout : 220 Seats
23700 l (6261 US gal)26692 l (7051 US gal) with 1 ACT - 29684 l (7842 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18604 kg (41015 lb)20953 kg (46193 lb) with 1 ACT - 23301 kg (51370 lb) with 2 ACT
Volume of CargoCompartments
51.72 m3 (1826.47 ft3)
Aircraft Data
TABLE 1
01-20-01Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV005 WV006 WV007 WV008
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
83400 kg(183865 lb)
78400 kg(172842 lb)
80400 kg(177252 lb)
89400 kg(197093 lb)
Maximum TakeoffWeight (MTOW)
83000 kg(182984 lb)
78000 kg(171961 lb)
80000 kg(176370 lb)
89000 kg(196211 lb)
Maximum LandWeight (MLW)
75000 kg(165347 lb)
74500 kg(164244 lb)
73500 kg(162040 lb)
75000 kg(165347 lb)
Maximum ZeroFuel Weight(MZFW)
71000 kg(156528 lb)
70500 kg(155426 lb)
69500 kg(153221 lb)
71500 kg(157630 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 46856 kg (103300 lb)With IAE Engines : 46959 kg (103527 lb)
Maximum Payloadwith CFM Engines
24144 kg(53228 lb)
23644 kg(52126 lb)
22644 kg(49921 lb)
24644 kg(54331 lb)
Maximum Payloadwith IAE Engines
24041 kg(53001 lb)
23541 kg(51899 lb)
22541 kg(49694 lb)
24541 kg(54104 lb)
Accommodation Typical Single Class Layout : 220 Seats
23700 l (6261 US gal)26692 l (7051 US gal) with 1 ACT - 29684 l (7842 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18604 kg (41015 lb)20953 kg (46193 lb) with 1 ACT - 23301 kg (51370 lb) with 2 ACT
Volume of CargoCompartments
51.72 m3 (1826.47 ft3)
Aircraft Data
TABLE 2
**ON A/C A321-200
2. This section gives general data (weight, payload, fuel capacity, ...) related to the A321-200 aircraft.Refer to the operator’s documentation for accurate values related to the specific aircraft.
Weight Variant WV000 WV001 WV002 WV003
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
89400 kg(197093 lb)
93400 kg(205912 lb)
89400 kg(197093 lb)
91400 kg(201502 lb)
01-20-01Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV000 WV001 WV002 WV003
Maximum TakeoffWeight (MTOW)
89000 kg(196211 lb)
93000 kg(205030 lb)
89000 kg(196211 lb)
91000 kg(200621 lb)
Maximum LandWeight (MLW)
75500 kg(166449 lb)
77800 kg(171520 lb)
77800 kg(171520 lb)
77800 kg(171520 lb)
Maximum ZeroFuel Weight(MZFW)
71500 kg(157630 lb)
73800 kg(162701 lb)
73800 kg(162701 lb)
73800 kg(162701 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 46856 kg (103300 lb)With IAE Engines : 46959 kg (103527 lb)
MaximumPayloadwith CFM Engines
24644 kg(54331 lb)
26944 kg(59401 lb)
MaximumPayloadwith IAE Engines
24541 kg(54104 lb)
26841 kg(59174 lb)
Accommodation Typical Single Class Layout : 220 Seats
23700 l (6261 US gal)26692 l (7051 US gal) with 1 ACT - 29684 l (7842 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18604 kg (41015 lb)20953 kg (46193 lb) with 1 ACT - 23301 kg (51370 lb) with 2 ACT
Volume of CargoCompartments
51.72 m3 (1826.47 ft3)
Aircraft
TABLE 3
Weight Variant WV004 WV005 WV006 WV007
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
87400 kg(192684 lb)
85400 kg(188275 lb)
83400 kg(183865 lb)
83400 kg(183865 lb)
Maximum TakeoffWeight (MTOW)
87000 kg(191802 lb)
85000 kg(187393 lb)
83000 kg(182984 lb)
83000 kg(182984 lb)
Maximum LandWeight (MLW)
75500 kg(166449 lb)
75500 kg(166449 lb)
75500 kg(166449 lb)
73500 kg(162040 lb)
Maximum ZeroFuel Weight(MZFW)
71500 kg(157630 lb)
71500 kg(157630 lb)
71500 kg(157630 lb)
69500 kg(153221 lb)
01-20-01Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV004 WV005 WV006 WV007
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 46856 kg (103300 lb)With IAE Engines : 46959 kg (103527 lb)
MaximumPayloadwith CFM Engines
69500 kg(153221 lb)
22644 kg(49921 lb)
MaximumPayloadwith IAE Engines
24541 kg(54104 lb)
22541 kg(49694 lb)
Accommodation Typical Single Class Layout : 220 Seats
23700 l (6261 US gal)26692 l (7051 US gal) with 1 ACT - 29684 l (7842 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18604 kg (41015 lb)20953 kg (46193 lb) with 1 ACT - 23301 kg (51370 lb) with 2 ACT
Volume of CargoCompartments
51.72 m3 (1826.47 ft3)
Aircraft Data
TABLE 4
Weight Variant WV008 WV009 WV010 WV011
Maximum RampWeight (MRW)Maximum TaxiWeight (MTW)
80400 kg(177252 lb)
78400 kg(172842 lb)
85400 kg(188275 lb)
93900 kg(207014 lb)
Maximum TakeoffWeight (MTOW)
80000 kg(176370 lb)
78000 kg(171961 lb)
85000 kg(187393 lb)
93500 kg(206132 lb)
Maximum LandWeight (MLW)
73500 kg(162040 lb)
73500 kg(162040 lb)
77800 kg(171520 lb)
77800 kg(171520 lb)
Maximum ZeroFuel Weight(MZFW)
69500 kg(153221 lb)
69500 kg(153221 lb)
73800 kg(162701 lb)
73800 kg(162701 lb)
Operating EmptyWeight (OEW) -Typical
With CFM Engines : 46856 kg (103300 lb)With IAE Engines : 46959 kg (103527 lb)
MaximumPayloadwith CFM Engines
22644 kg(49921 lb)
26944 kg(59401 lb)
01-20-01Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Variant WV008 WV009 WV010 WV011
MaximumPayloadwith IAE Engines
22644 kg(49921 lb)
26841 kg(59174 lb)
Accommodation Typical Single Class Layout : 220 Seats
23700 l (6261 US gal)26692 l (7051 US gal) with 1 ACT - 29684 l (7842 US gal) with 2 ACT
Usable FuelCapacity(Density = 0.785kg/l)
18604 kg (41015 lb)20953 kg (46193 lb) with 1 ACT - 23301 kg (51370 lb) with 2 ACT
Volume of CargoCompartments
51.72 m3 (1826.47 ft3)
Aircraft Data
TABLE 5
01-20-01Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
SURVEY
02-00-00 SURVEY
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 02-00-00-001-A01
General
1. IntroductionThe objective is to define a recovery scenario based on a recovery plan and implement it:- Without causing secondary damage,- By ensuring traceability of actions performed.The recovery must be set up and controlled according to a recovery process.If a recovery contributing factor (see FIGURE 02-00-00-991-001-A) changes or is not as expected,each section must be reviewed to reconsider the recovery process.The recovery process is detailed in chapter 02-10-01 and is valid when there is no worldwide recoverystandard procedure for events of an infinite variety, even if there are basic leveling techniques:- Use of Jacks (see 06-30-00),- Use of Pneumatic Lifting Bags (see 06-40-00),- Use of Cranes (see 06-50-00).The ARM planning chart, aircraft recovery logic chart or the IATA aircraft recovery quick referencechecklist could be used to support this recovery process (see 09-20-01).
2. Recovery Secondary DamageThe objective of a successful aircraft recovery operation is to move the aircraft from the incident oraccident site to a repair area or facility without causing any secondary damage.The secondary damage is a damage which is not due to the initial event, and can increase the repairtime. However, due to time or cost constraints, secondary damage will be accepted from involvedparties. In that case make sure that the time saving is acceptable in comparison with the cost.The insurance underwriters can probably contest any secondary damage. Therefore every step of therecovery process must be continually monitored with appropriate action taken to prevent it.
NOTE : The damage on airport infrastructure or field can be considered as secondary damage ifadequate action is not done in due time.
02-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
LOCATION OF RECOVERY AIRCRAFT SECURITY
MISCELLANEOUS
TOWING / DEBOGGING
AIRCRAFT LEVELING
AIRCRAFT LIFTING
AIRCRAFT TETHERING
TERRAIN ANALYSIS
AIRCRAFT AND TOOLINGSTABILITY
REPAIR TO ENABLERECOVERY
AIRCRAFT WEIGHT ANDBALANCE MANAGEMENT
INTENTIONALSECONDARY DAMAGE
OPERATION CONTROL−MONITORING REPORTING
POST RECOVERYACTIONS DUE TO
RECOVERY SCENARIO
AIRCRAFT RELEASEFROM INVESTIGATIVE
AUTHORITY− PLANNING− LEAD TIME− LOGISTICS− CONTRACT
RECOVERYSCENARIO
TOOLING AVAILABILITY
AIRCRAFT DAMAGEASSESSMENT FOR
RECOVERY PURPOSE
N_AR_020000_1_0010101_01_01
Recovery ProcessContributing Factors
FIGURE-02-00-00-991-001-A01
02-00-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
02-10-01 CHARTS AND GUIDES
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 02-10-01-001-A01
Aircraft Recovery Process
1. GeneralThe recovery methods used are specific to each recovery operation, are dependent on multiple driversand constraints, including non aircraft specific drivers, as well as the individual aircraft recoveryconsiderations.The recovery process can be divided into five basic sections:- Survey,- Planning,- Preparation,- Recovery,- Reporting.
A. Survey
(1) Before you get access to the incident or accident site and while waiting for release of theaircraft from the Investigative Authorities, some preliminary tasks can be carried out.Some general issues are:- Get and record the initial incident or accident data,- Secure the site: fire, theft and access control,- Confirm that members of the Aircraft Recovery Team are available,- Arrange delivery of any local aircraft recovery equipment,- Make communication with airport and Investigative Authorities,- Identify the hazardous materials which are on board,- Get an airport plan to assess aircraft or recovery team travel path difficulty, etc.
(2) After access to the incident or accident site, you must do a detailed inspection and arecord of the items that follow:- Integrity of the aircraft structure and landing gear,- Survey of the soil conditions,- Local weather conditions,- Personnel health and safety issues,- Environmental concerns.
(3) The other issues to consider if the incident took place at a secondary or internationalairport are:- Transportation of personnel and equipment,- Visas, passports and vaccinations certificates,- Hotels and local transport.
B. PlanningThe main planning issues are (not in order of importance) :
02-10-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
- Identification of your recovery drivers,- Adverse weather conditions or critical forecast which can have an impact on material
required, recovery plan and recovery team operation, etc.- Limitation of airport use with the disabled aircraft,- Type of leveling, lifting or removal plan,- Aircraft weight and balance management operation, if necessary,- Unserviceable aircraft systems,- Storage of removed fuel,- Aircraft movement possibility and path,- Compilation of all corrective actions, necessary logistics and planning,- Necessary tooling.
C. PreparationThe main preparation issues are (not necessary in the applicable order) :- Control weight and CG by removal or transfer of the required amount of fuel and payload,- Make the aircraft stable,- Assemble the required equipment for the leveling/lifting method that you will use,- Remove components which are damaged,- Remove components to help the weight reduction,- Test and stabilize the soil if necessary.
D. RecoveryThe main recovery issues are (in priority order) :- Obey the safety conditions for personnel,- Monitor and record load when you level, lift and move the aircraft,- Level the aircraft as required,- Lift the aircraft as required,- Move the aircraft.
E. ReportingIt is necessary to do the recovery records. The Recovery Manager must hand these records overto the maintenance team. They will be used to do the necessary corrective action and releasethe aircraft back to service, for systems and structure.
02-10-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 02-10-01-002-A01
Aircraft Recovery Logic Chart
1. GeneralThe Aircraft Recovery Logic Charts (see DESC 09-20-01-002-A01) are an aid for the AircraftRecovery Manager and his team. The recovery charts describe the necessary steps of the recoveryprocess and can be used as a checklist by ticking off the boxes when completed. Although detailed,the chart must be used with the complete ARM. These charts give the specific areas of the ARMwhere you can find additional and more detailed data on a specific subject.
02-10-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
02-20-01 INITIAL AIRCRAFT SURVEY
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 02-20-01-285-801-A01
Initial Aircraft Survey
1. GeneralA detailed aircraft condition report must be completed as soon as possible to help the basic approachto the recovery process, to ensure safety of the personnel and to anticipate the repairs. Theinspection and the subsequent report do not need to be as detailed for the recovery as for repair ofthe aircraft.Photographs, sketches, measurements, notes, etc. can complete the documentation. Digital cameras,video recorders and pocket audio recorders can help to record the data.The documentation will help engineering staff, insurance surveyors and manufacturer representativesto discuss the details of the recovery scenarios/options. This information will be helpful to fill in areport when the recovery is completed.The future airworthiness of the aircraft can be dependent on the accuracy of the data recorded duringthe recovery operation. These records must include accurate figures on all loads applied to theaircraft during the recovery.In most cases, the accident investigation will be more important than the aircraft recovery process.The objective of the accident investigation is to determine the cause of the incident or accident andprovide details to prevent the re-occurrence of such an event.Keep in mind that the time between the notification of the event and release of the aircraft by theInvestigative Authorities can be several hours.If the Investigative Authority asks for removal of the Aircraft Flight Data and Cockpit VoiceRecorders, qualified personnel must do it and obey AMM procedures. These units are to be handedover to the Investigative Authority. In return, the Investigative Authority will give you a receipt withthe aircraft registration and the serial numbers of the removed units.It is necessary to note current and forecast weather.
2. InspectionsIt is necessary to estimate the fuel quantity, the cargo on board.It is also necessary to identify and quantify hazardous materials with any required personnelprotective equipment.
3. Job Setup ReferencesNot Applicable.
02-20-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONAMM
Referenced Information
TABLE 1
5. Procedure
WARNING : DO NOT CLIMB ON, GO INTO OR GO BELOW THE AIRCRAFT UNTIL THEAIRCRAFT IS STABLE.
WARNING : MAKE SURE THAT THE AIRCRAFT IS CORRECTLY GROUNDED.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
Subtask 02-20-01-284-001-A01
A. Inspection of Damage
(1) Without climbing on, going into or going below the aircraft, identify and record all obviousand visible damage. Note the location on the fuselage with frame (station) and stringernumbers, and on the wing with rib and station numbers.
(2) The types of damage include cracked, creased, distorted or torn fuselage and wing skinpanels and also missing or broken fasteners (bolts, rivets…) and fittings.
(3) These types of damage are signs of failed structural components and must be considered assuspect. These failed structural components cannot be relied on to carry their designedloads. It is necessary to do a more detailed inspection on these areas prior to leveling,lifting or moving the aircraft.
(4) It is necessary to record any evidence of fire or overheating.
(5) It is also necessary to identify missing and damaged components such as landing gear, flapsections and non-structural fairings. Broken fairings can be a sign of hidden damage toother structural areas.
(6) It is necessary to do a more detailed inspection on these areas prior to leveling, lifting ormoving the aircraft.
Subtask 02-20-01-680-001-A01
B. Fluid Leaks
(1) Fluid leaks must be identified.
02-20-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(2) These fluid leakages can be fuel, hydraulic fluid, lavatory waste water, potable water andany fluid transported in the cargo compartments.At the first indication of a fluid leak, the airport or Investigative Authorities must call for ahazardous materials response company to contain these leaking fluids.
(3) Cap lines and manually close valves to stop or control fluid leaks. Or temporarily plug holesor openings to stop the flow. If there is a fuel leak, defueling must be a primary task.
NOTE : This step can be required at any point during the initial aircraft survey.
Subtask 02-20-01-862-001-A01
C. Batteries
(1) If there is any structural damage on the fuselage or wings, it is necessary to remove orisolate the aircraft batteries as soon as the aircraft is stable.
NOTE : This step can be required at any point during the initial aircraft survey.
(2) It is possible to keep the batteries connected if there is no structural or system damage.This can be useful later for the recovery process. This decision can be re-examined duringthe survey and recovery.
NOTE : At this point, it is possible to try to make the aircraft stable and safe so that it ispossible to do a detailed inspection in and below the aircraft.
Subtask 02-20-01-869-001-A01
D. Landing Gear
WARNING : MAKE SURE THAT LANDING GEAR DOWNLOCK PINS ARE INSTALLED IFTHEIR INSTALLATION IS POSSIBLE.
(1) If a landing gear malfunction caused the event, it can be possible to continue to use theaircraft landing gear to move the aircraft when lifted. It is necessary to make sure that thestructure and landing gear (when extended) can support the aircraft weight. Examples are:- One or more landing gear(s) remained retracted at touchdown,- One or more landing gear(s) collapsed after touchdown due to downlock failures,- One or more landing gear(s) folded or collapsed when the aircraft left the runway and
bogged down in mud, snow or sand.
(2) In these cases, it can be possible to extend and lock the landing gear down after lifting theaircraft and after carrying out temporary repairs to strengthen or brace damaged parts. Ifrepairs are necessary, it is usually less difficult and less time consuming to do these repairsthan to have secondary damage when moving the aircraft on a trailer or a recoverytransport vehicle.
(3) Make sure that spare landing-gear assemblies are available to replace damaged or missingones, if required.
02-20-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
02-20-02 INITIAL SITE SURVEY
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 02-20-02-285-801-A01
Initial Site Survey
1. GeneralThis procedure gives details on how to do a full survey of the incident site around the aircraft.
2. InspectionsNot Applicable.
3. Job Setup ReferencesGet an airport map from the airport authority (we recommend a topographical map, which includessubterranean infrastructure localization) of the incident area.
4. Procedure
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
Subtask 02-20-02-285-001-A01
A. Terrain
(1) If the ground is sufficiently flat, the recovery process can be more direct. It will be moredifficult to move the aircraft on a rolling terrain with hills and it can be necessary to gradethe ground.You can report on the airport site plan the position of the aircraft, the flatness, slopes,hills, width and depth of any ditches or culverts and surrounding vegetation. You canexamine the area to know if there is any animal life (rodents and snakes).
Subtask 02-20-02-285-002-A01
B. Soil Characteristics
(1) The load bearing capacity is very important. This information is necessary to set up thesupport equipment to level, lift or move the aircraft.It is also necessary to do the selection of the type of tethering. The type of ground anchorsis dependent on the soil properties.
(2) The type of soil can be noted in addition to the substrate. It is possible to use the rutsmade by the landing gear to identify the subsurface soil type.
(3) Subterranean airport infrastructure must be known.Signs of recent excavations must be noted. The airport site plan must be amended toindicate any of these areas. Signs of recent excavations usually show soft and unstableground.
02-20-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
This information is very important, as it will influence the path to move the aircraft duringthe recovery.
(4) One of the standards used to compare different soil conditions is the California BearingRatio or CBR.This test measures the load necessary to make a plunger of a standard area penetrate asoil sample. The information is recorded on a standard graph and the plot of the test givesthe CBR result of the soil test.The CBR is a procedure to put a figure on the inherent strength of the soil. The soil musthave a homogeneous CBR rating through a sufficient depth. For more details, you can referto a ground engineer.
(5) The possible effect of rainfall on the ground load bearing capabilities can change with thesurface hardness, smoothness or drainage.Use pumps to remove standing water and dig drainage ditches from the work area.
Subtask 02-20-02-500-001-A01
C. Access Routes
(1) Access routes to the incident site can be planned with the airport site map. In most cases,it is necessary to go across active runways.The air traffic control service must plan and control these routes.
(2) Carefully review of the path of the aircraft from the runway to the resting point.The distance to runways, taxiways and aprons, the type of soil, rut depth and terrain willall influence in which direction the aircraft will be moved once the actual recovery starts.
(3) Pavement requirements for the particular aircraft are derived from the static analysis ofloads imposed on the main landing gear struts.These main landing gear loads are used as the point of entry to the pavement designcharts (See AC-07-00-00).Make sure that the surfaces you will move the aircraft on are able to support these loads.
(4) Make sure that the specific ground tooling or road used to level, lift or move the aircraftare able to support aircraft load.
(5) Make sure that the loads applied to the aircraft are not more than aircraft allowable loads.
Subtask 02-20-02-869-001-A01
D. Weather
(1) Weather conditions can play a major role during aircraft recovery operations. Generalmeteorological conditions (temperature, wind speed and precipitation) must be recorded.
(2) Temperature, both extreme heat and extreme cold, will determine the type of clothing,meals and liquid intake for the manpower involved in the recovery. The need for shelterfrom heat or cold will also have to be determined.
02-20-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(3) Forecast conditions must be acquired and recorded. The forecast will help to prepare thetype of personal protective clothing and to determine the recovery plan.
(4) Make sure that the required tooling can be used within forecast conditions.
(5) Wind and projected wind gust speeds will determine the amount of tethering and willinfluence any attempts at lifting the aircraft.
(6) Any type of precipitation will have consequences in the grading, soil support and generalrecovery operation.
02-20-02Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
02-30-01 LANDING GEAR
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 02-30-01-200-801-A01
Landing Gear Survey
1. General
WARNING : LET THE BRAKES AND THE WHEELS BECOME COOL BEFORE YOU GO NEARTHE LANDING GEAR. DO NOT APPLY A LIQUID OR GAS FIRE EXTINGUISHERDIRECTLY ON A HOT WHEEL OR BRAKE UNIT. IF YOU DO NOT OBEY THESEPRECAUTIONS, THERE IS A RISK OF EXPLOSION.
WARNING : MAKE SURE THAT THE LANDING GEAR AND DOOR TRAVEL RANGES ARECLEAR. MOVEMENT OF THE LANDING GEAR AND DOORS CAN CAUSE INJURYAND/OR DAMAGE.
WARNING : MAKE SURE THAT THE LANDING GEAR IS UPLOCKED BEFORE YOU OPENTHE GEAR DOORS MANUALLY. IF THE GEAR IS NOT UPLOCKED, THEWEIGHT OF THE GEAR CAN BE ON THE DOORS. IF YOU OPEN THE DOORS INTHIS CONDITION, THERE IS A RISK THAT THE LANDING GEAR WILL EXTENDBY GRAVITY AND CAUSE INJURY.
The principles outlined in this chapter are provided as a guide to assist aircraft recovery.The chapter gives the general inspections required to find the extent of any damage to the landinggear and the recommended steps required to recover the aircraft.You must do the applicable inspections before moving the aircraft.For the description of the landing gears, see 09-10-16.
2. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Devices
on Landing Gears
09-10-16 09-10-16-LANDING GEARS04-20-00 04-20-00-STABILIZING THE AIRCRAFT07-60-00 07-60-00-MOVING DAMAGED AIRCRAFT07-40-03 07-40-03-TOWING WITH DEFLATED TIRES07-40-00 07-40-00-TOWING AND DEBOGGING06-00-00 06-00-00-LEVELING AND LIFTINGAMM 29-10-00-864AMM 24-41-00-862AMM 32-51-00-040AMM 32-40-00-040
02-30-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
REFERENCE DESIGNATIONFIGURE 02-30-01-991-001-A FIGURE 02-30-01-991-001-A-Landing Gear
FIGURE 02-30-01-991-002-A FIGURE 02-30-01-991-002-A-Landing Gear
Referenced Information
TABLE 1
3. Procedure
Subtask 02-30-01-867-001-A01
A. Safety Precautions
(1) Make sure that the aircraft is stable, see 04-20-00.
(2) Make sure that the Ground Lock Pins are installed on the landing gear where possible, seeTASK 02-30-01-481-801-A01.
(3) Make sure that the MLG and NLG wheels are chocked where possible.
(4) Make sure that the Landing Gear Control Lever (6GA) is in the DOWN position and put awarning notice to tell people not to operate the landing gear.
(5) On the center pedestal, make sure that the Free-Fall Control-Handle is in normal positionand safe, see FIGURE 02-30-01-991-001-A.
(6) If the aircraft wheel brake hydraulic circuits are serviceable:
(a) On the center pedestal, see FIGURE 02-30-01-991-002-A, set the PARK BRK switchto the ON position.
(b) On the center panel, see FIGURE 02-30-01-991-002-A, make sure that the pressureindication on the triple-indicator is correct. The indicator must be in the Green area.
(c) Make sure that the Green and Yellow hydraulic systems are depressurized, see AMM29-10-00-864.
(d) Make sure that the aircraft electrical circuits are de-energised, see AMM24-41-00-862.
(7) Put safety barriers around the Landing Gear(s) that are not correctly extended anddownlocked.
Subtask 02-30-01-867-003-A01
B. Landing Gear Positions
(1) A Landing Gear can be found in the following conditions:
(a) Fully extended and downlocked.
(b) Not fully extended or retracted.
(c) Retracted and uplocks released (Landing Gear Doors closed).
02-30-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(d) Retracted and uplocked.
(e) Collapsed or missing.
(f) Bogged.
WARNING : IF THE LANDING GEAR DOES NOT FULLY EXTEND WHEN THE AIRCRAFTIS LEVEL, SAFETY THE LANDING GEAR TO PREVENT UNWANTEDMOVEMENT.
(2) Before doing the inspection, make sure you know the position of the Landing Gear.
(a) Landing Gear fully extended and downlocked, see TASK 02-30-01-481-801-A01:
1 Do the applicable inspection for that Landing Gear (NLG or MLG).
(b) Landing Gear not fully extended or retracted:
1 See 06-00-00 for the procedure to level and lift the aircraft.
2 It will be necessary to secure the Landing Gear to prevent it travelling furtherand becoming a danger to anyone or to the recovery operations.
3 To support the gear, put a hydraulic lifting platform (lifting capacity 7 tonnes)under the Landing Gear to be supported. Make sure that the lifting surface iscovered with support materials, such as tires or foam, to protect the LandingGear from damage.
4 To further support the gear, raise the platform until the support materials makegood contact with the Landing Gear to prevent accidental movement of the gearduring the inspection.
5 You must make sure that all other ground lock pins are installed, then in thecockpit, rotate the free-fall extension-handle for three revolutions to clockwise.This will open the hydraulic system to RETURN and allow the unlocked leg tobe lifted. See FIGURE 02-30-01-991-001-A.
6 Do the applicable inspection for that Landing Gear (NLG or MLG).
(c) Landing Gear Retracted and uplocked:
1 If the NLG is retracted and uplocked, it must be lowered and downlocked beforean inspection can be done, see TBD for the manual extension procedure.
2 If the MLG is retracted and uplocked, it must be lowered and downlocked beforean inspection can be done, see TBD for the manual extension procedure.
(d) Landing Gear Retracted and uplocks released (Landing Gear Doors closed) :
1 If the NLG is retracted with the Landing Gear Doors closed, see TBD for theprocedure to manually extend the gear, then do the applicable inspection.
2 If the MLG is retracted with the Landing Gear Doors closed, see TBD for theprocedure to manually extend the gear, then do the applicable inspection.
02-30-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(e) Landing Gear Collapsed or missing:If a Landing Gear is collapsed, missing or unusable, see 07-60-00 for the procedure tomove a damaged aircraft using special recovery vehicles.
(f) Landing Gear locked down and bogged down:
1 Do the applicable inspection for that Landing Gear (NLG or MLG).
2 See TBD for the debogging procedure.
Subtask 02-30-01-867-004-A01
C. Landing Gear Inspection
(1) Main Landing Gear
(a) Do a visual inspection of the Main Landing Gear, the attachments to the Airframe,the doors. Look for signs of distortions, cracks and ruptures. If this type of damage isfound on a component, it must be replaced before you move the aircraft.
(b) The following components can be removed if they are not usable or if they willimpede the recovery operation:- The wheel brake components, see AMM 32-40-00-040 for information on the
deactivation of brake components before you remove them- The Main Door- The Hinged and Fixed Fairings.
(c) If the repair or replacement of damaged components is not possible because of generalarea damage, the aircraft must be recovered on specialist recovery vehicles, see07-60-00.
(d) Do a visual inspection of the tires. If there are deflated tires, see 07-40-03 for theapplicable limitations.
(2) Nose Landing Gear
(a) Do a visual inspection of the Nose Landing Gear, the attachments to the Airframe,the two Forward and two Aft Doors. Look for signs of distortions, cracks andruptures. If this type of damage is found on a component, it must be replaced beforeyou move the aircraft.
(b) The following components can be removed if they are not usable or if they willimpede the recovery operation:- The Forward Doors- The Aft Doors- The Nosewheel Steering components.
(c) See AMM 32-51-00-040 for the procedure to deactivate the NWS.
(d) If the repair or replacement of damaged components is not possible because of generalarea damage, the aircraft must be recovered on specialized recovery vehicles, see07-60-00.
02-30-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(e) If the NLG is bogged, see TBD. If the NLG is on a hard surface see 07-40-00
(f) Do a visual inspection of the tires. If there are deflated tires, see 07-40-03 for theapplicable limitations.
02-30-01Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
L/G EXTENSION/RETRACTION LEVER
L/G MANUAL EXTENSION HANDLE
N_AR_023001_1_0010101_01_00
G R A V I T Y
GEARE X T N
TURN
A
B
A
P U L L
GEAR R
AEG
B
Landing GearLG Control Lever and Free-Fall Control Handle
FIGURE-02-30-01-991-001-A01
02-30-01Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_023001_1_0020101_01_00
P S I x 1 0 0 0BRAKES
0
13
13
40
ACCU PRESS
PARKING BRK OFF
PARK BRKON
A
B
A
B
Landing GearBrakes - Indication and ControlFIGURE-02-30-01-991-002-A01
02-30-01Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 02-30-01-481-801-A01
Installation of the Safety Device on Landing Gears
1. General
WARNING : LET THE BRAKES AND THE WHEELS BECOME COOL BEFORE YOU GO NEARTHE LANDING GEAR. DO NOT APPLY A LIQUID OR GAS FIRE EXTINGUISHERDIRECTLY ON A HOT WHEEL OR BRAKE UNIT. IF YOU DO NOT OBEY THESEPRECAUTIONS, THERE IS A RISK OF EXPLOSION.
WARNING : MAKE SURE THAT THE LANDING GEAR AND DOOR TRAVEL RANGES ARECLEAR. MOVEMENT OF THE LANDING GEAR AND DOORS CAN CAUSE INJURYAND/OR DAMAGE.
WARNING : MAKE SURE THAT, IF THE LANDING GEAR DOORS ARE OPEN, THEY ARESAFETIED BEFORE YOU INSTALL THE LANDING GEAR SAFETY-DEVICES. IFTHE LANDUNG GEAR DOORS ARE OPEN BUT NOT SAFETIED THERE IS ARISK THAT THEY VCAN CLOSE AND CAUSE INJURY.
WARNING : MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES AREIN POSITION BEFORE YOU START A TASK ON OR NEAR THE FLIGHTCONTROLS, THE FLIGHT CONTROL SURFACES, THE LANDING GEARS ANDRELATED DOORS AND COMPONENTS THAT MOVE. MOVEMENT OFCOMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND CAN CAUSEDAMAGE.
The chapter gives the recommended steps to install the safety devices on the landing gears andlanding gear doors prior to recover the aircraft.For the description of the landing gears, see 09-10-16.
2. InspectionsNot Applicable.
3. Job Setup References
A. Safety PrecautionsMake sure that the aircraft is stable, see 04-20-00.Make sure that the MLG and NLG wheels are chocked where possible.Make sure that the Landing Gear Control Lever (6GA) is in the DOWN position and put awarning notice to tell people not to operate the landing gear.On the center pedestal, make sure that the Free-Fall Control-Handle is in normal position andsafe.
02-30-01Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATIOND23080000 PIN-GROUND LOCK, NLG
MZ23080000 PIN - NLG DOWNLOCK SAFETYDRT68031 SLEEVE - GROUND LOCKDRT68923 SLEEVE-GROUND LOCK460005833 GROUND LOCK SLEEVE460007280 SLEEVE-GROUNDLOCK460005835 GROUND LOCK SLEEVEDAH602734 GROUND LOCK SLEEVE98D32203502000 SAFETY PIN - NLG DOOR
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATION09-10-16 09-10-16-LANDING GEARS04-20-00 04-20-00-STABILIZING THE AIRCRAFTAMM 32-12-00-010-001AMM 32-22-00-010-001
Referenced Information
TABLE 2
5. Procedure
Subtask 02-30-01-481-003-A01
A. Installation of the Safety Devices on the Landing Gears
(1) To install the left and right Main Landing Gear Safety Locks:
(a) If a landing gear door is open, make sure:- the ground door-opening handle is in the open position- the ground door-safety lock is installed, see SUBTASK 02-30-01-481-004-A01.
(b) Make sure that the piston rod of each lock stay actuating cylinder is clean.
NOTE : There are four alternative tools that can be used for this task:- DRT68031 SLEEVE - GROUND LOCK- DRT68923 SLEEVE-GROUND LOCK- 460005833 GROUND LOCK SLEEVE- 460007280 SLEEVE-GROUNDLOCK
02-30-01Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(c) Remove the pin and open the GROUND LOCK SLEEVE.
(d) Make sure that the GROUND LOCK SLEEVE is clean and in the correct condition.
(e) Put the GROUND LOCK SLEEVE in position on the piston rod of each lock stayactuating cylinder.
(f) Close the GROUND LOCK SLEEVE and install the pin from the inboard side.
(g) Make sure that the flag is in view.
(2) To install the Nose Landing Gear Safety Lock:
(a) If a landing gear door is open, make sure:- the ground door-opening handle is in the open position- the ground door-safety lock is installed, see SUBTASK 02-30-01-481-004-A01.
(b) Make sure that the holes in the NLG lock stay are aligned.
NOTE : There are two alternative tools that can be used for this task:- D23080000 PIN-GROUND LOCK, NLG- MZ23080000 PIN - NLG DOWNLOCK SAFETY
(c) Make sure that the D23080000 PIN-GROUND LOCK, NLG or the MZ23080000 PIN -NLG DOWNLOCK SAFETY is in a clean and correct condition.
(d) Install the D23080000 PIN-GROUND LOCK, NLG or the MZ23080000 PIN - NLGDOWNLOCK SAFETY in the holes in the NLG lock stay.
(e) Make sure that the flag is in view.
Subtask 02-30-01-481-004-A01
B. Installation of the Safety Devices on the Landing Gears Doors
(1) To install the safety devices on the main landing gear doors:
(a) Open the applicable MLG door(s). See AMM 32-12-00-010-001.
1 Make sure that the piston rod of the MLG door actuating cylinder is clean.
(b) Remove the pins (1) and open the 460005835 GROUND LOCK SLEEVE or theDAH602734 GROUND LOCK SLEEVE.
(c) Make sure that the ground lock sleeve is in a clean and correct condition.
(d) Put a ground lock sleeve in position on the piston rod of each of the MLG dooractuating cylinders.
(e) Close the ground lock sleeve and install the pins (1) from the top.
(f) Make sure that the flag is in view.
(2) To install the safety devices on the nose landing gear doors:
(a) Open the NLG doors. See AMM 32-22-00-010-001.
(b) Make sure that the holes in the NLG doors and the hinges are aligned.
02-30-01Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(c) Make sure that each 98D32203502000 SAFETY PIN - NLG DOOR is in a clean andcorrect condition.
(d) Install a 98D32203502000 SAFETY PIN - NLG DOOR through the holes in each NLGdoor and hinge.
(e) Make sure that the flag is in view.
02-30-01Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
FLAG
LOCKSTAYACTUATING
CYLINDER
N_AR_023001_1_0200101_01_00
LOCKSTAYACTUATINGCYLINDER
GROUND LOCK SLEEVE
FLAG
DOWNLOCKSAFETY PIN
LOCKSTAY
A
B
A
B
Landing GearInstallation of the Safety DevicesFIGURE-02-30-01-991-020-A01
02-30-01Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DOORACTUATINGCYLINDER
FLAG
DOOR HINGE
NLG DOOR
NLG DOORSAFETY PIN
FLAG
FOR DETAIL B, PROXIMITY SENSORS OMITTED FOR CLARITYNOTE:
MAIN DOOR
N_AR_023001_1_0210101_01_00
MLG DOORACTUATINGCYLINDER
1
A
LH SYMETRICAL
B
A
RH SHOWN
B
Landing Gear DoorsInstallation of the Safety DevicesFIGURE-02-30-01-991-021-A01
02-30-01Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 02-30-01-867-802-A01
Jacking for Wheel Change
1. General
WARNING : LET THE BRAKES AND THE WHEELS BECOME COOL BEFORE YOU GO NEARTHE LANDING GEAR. DO NOT APPLY A LIQUID OR GAS FIRE EXTINGUISHERDIRECTLY ON A HOT WHEEL OR BRAKE UNIT. IF YOU DO NOT OBEY THESEPRECAUTIONS, THERE IS A RISK OF EXPLOSION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE CORRECTLYINSTALLED ON THE LANDING GEAR. THIS PREVENTS UNWANTEDMOVEMENT OF THE LANDING GEAR.
CAUTION : DO NOT DO THIS JACKING FOR WHEEL CHANGE PROCEDURE DURINGREFUELING OR DEFUELING PROCEDURES. IF THE AIRCRAFT IS ON JACKSAND IF A FIRE OR IMPORTANT FUEL SPILLAGE OCCURS IT WILL NOT BEPOSSIBLE TO MOVE THE AIRCRAFT.
This procedure gives details for the replacement of a wheel with deflated tires.
2. InspectionsNot Applicable.
3. Job Setup ReferencesYou can lift the aircraft at its maximum weight.
Hydraulic Jack Data Capacity (min) Closed Height (max) Hydraulic Stroke (min)
Nose Gear 10000 daN (22481 lbf) 130 mm (5.12 in) 171 mm (6.73 in)
Nose Gear (usingInclined Blocks)
10000 daN (22481 lbf) 200 mm (7.87 in) 171 mm (6.73 in)
Main Gear (TwinWheel)
35000 daN (78683 lbf) 215 mm (8.46 in) 334 mm (13.15 in)
Main Gear (Four WheelBogie)
35000 daN (78683 lbf) 125 mm (4.92 in) 255 mm (10.04 in)
Hydraulic Jack Specifications
TABLE 1
NOTE : If both tires of the nose landing gear are deflated at the same time, the maximum closedheight of the hydraulic jack must be 128 mm (5.04 in). Use specific tool TMHCP07-00-00WHEEL CHANGE AXLE JACK.
02-30-01Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATIONGSE WHEEL CHANGE JACKTMHCP07-00-00 WHEEL CHANGE AXLE JACK
Fixtures, Tools, Test and Support
TABLE 2
B. Referenced Information
REFERENCE DESIGNATIONAMM 32-41-12PB401AMM 05-51-15-200-001AMM 32-41-11PB401FIGURE 02-30-01-991-019-A FIGURE 02-30-01-991-019-A-Nose Landing Gear
FIGURE 02-30-01-991-022-A FIGURE 02-30-01-991-022-A-Nose Landing Gear
FIGURE 02-30-01-991-023-A FIGURE 02-30-01-991-023-A-Jacking for Wheel Change
Referenced Information
TABLE 3
5. Procedure
Subtask 02-30-01-869-001-A01
A. Safety Precautions
(1) Make sure that the wheels are on the aircraft axis.
(2) Make sure that there is sufficient space around the aircraft.
(3) Make sure that the aircraft is clear to lift.
(4) Make sure that the aircraft is stable.
(5) Make sure that the jack adapter is in correct condition.
Subtask 02-30-01-581-001-A01
B. Jacking of the Nose Landing Gear
(1) See FIGURE 02-30-01-991-019-A.See TABLE 1 for hydraulic jack specifications.
(2) Install the wheel chocks on the main landing-gear wheels.
02-30-01Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(3) Put the GSE WHEEL CHANGE JACK so that its adapter touches the ball-pad of the shockabsorber.
NOTE : If both tires of the nose landing gear are deflated at the same time, themaximum closed height of the hydraulic jack must be 128 mm (5.04 in). Usespecific tool TMHCP07-00-00 WHEEL CHANGE AXLE JACK.
(4) Make sure that the wheel jack is stable and in the vertical position.
(5) Make sure that this assembly is level.
(6) Operate the jack to lift the tire off the ground.
(7) Change the wheel, see AMM 32-41-12PB401.
(8) Operate the control of the hydraulic jack slowly to lower the aircraft. Do not lower theaircraft on its wheels suddenly.
(9) When the aircraft is on its wheels, remove the hydraulic jack.
Subtask 02-30-01-581-002-A01
C. Towing of the NLG on Inclined Blocks Before Jacking
(1) This procedure is necessary when the height of the closed jack is more than the heightbetween the ground and the jacking dome. See FIGURE 02-30-01-991-022-A.
Inclined Block Angle (max) Height (min)
Nose Gear 5 degrees 100 mm (3.94 in)
Inclined Blocs Specifications
TABLE 4
The inclined blocks must have sufficient strength to support the aircraft weight.The inclined blocks can be made from:- Heavy timbers or railroad crossties,- Plywood sheets covered with a steel plate of 6 mm (0.24 in) minimum thickness,- Plywood sheets covered with a light-alloy sheet of 20 mm (0.79 in) minimum thickness.
(2) Tow the aircraft a small distance to make sure that the nose wheels turn freely.
(3) Do the inspection after a tire burst or thread throw or wheel failure, see AMM05-51-15-200-001.
(4) Make sure that GSE WHEEL CHANGE JACK and the INCLINED BLOCKS are in correctcondition.
(5) Put one inclined block below each nose wheel. Make sure that:- The axes of the inclined block are aligned with the A/C centerline,- The position of the inclined block lets you install the hydraulic jack below the jacking
dome.
02-30-01Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(6) For the towing on the inclined blocks, there must be one person in the cockpit to operatethe brakes if necessary, and two persons to monitor the wing tips.
(7) Pull or push the aircraft on the top flat area of the inclined block.
(8) Put the wheel chocks in position in front of and behind the MLG wheels.
(9) Remove the towbar from the NLG fitting.
(10) Set the PARKING BRK control switch to OFF.
(11) Put the GSE WHEEL CHANGE JACKin position and adjust the jack until its adaptertouches the jacking dome of the shock absorber.
(12) Make sure that the wheel jack is stable and in the vertical position.
(13) Operate the jack to lift the tire off the inclined block.
(14) Remove the inclined block.
(15) Change the wheel, see AMM 32-41-12PB401.
(16) Operate the control of the hydraulic jack slowly to lower the aircraft. Do not lower theaircraft on its wheels suddenly.
(17) When the aircraft is on its wheels, remove the hydraulic jack.
Subtask 02-30-01-581-003-A01
D. Jacking of the Main Landing Gear
(1) See FIGURE 02-30-01-991-023-A.See TABLE 1 for hydraulic jack specifications.
(2) Install the wheel chocks on the main landing-gear that is not necessary to change.Install the wheel chocks on the nose landing-gear.
(3) Put the GSE WHEEL CHANGE JACK so that its adapter touches the ball-pad of the shockabsorber.
(4) Make sure that the wheel jack is stable and in the vertical position.
(5) Operate the jack to lift the tire off the ground.
(6) Change the wheel, see AMM 32-41-11PB401.
(7) Operate the control of the hydraulic jack slowly to lower the aircraft. Do not lower theaircraft on its wheels suddenly.
(8) When the aircraft is on its wheels, remove the hydraulic jack.
02-30-01Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
25.4
mm
301 mm
40 m
m A
PP
RO
X
9°
198
mm
(1 in
)
(11.85 in)
(1.5
7 in
)
(7.7
9 in
)
128
mm
(5.0
4 in
)
JAC
KIN
G P
OIN
T
N_A
R_0
2300
1_1_
0190
101_
01_0
0
A
A
AA
Nose Landing GearJacking for Wheel Change
FIGURE-02-30-01-991-019-A01
02-30-01Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_023001_1_0220101_01_00
9°
198 mm(7.79 in)
(7.87 in)
(3.93 in)
INCLINED BLOCK
INCLINED BLOCK
DIMENSION "D" MUST BE MORE THAN HYDRAULIC JACK WIDTH.
==
D
5° MAX
200 mm MIN (APPROX.)
100 mm MIN
NOTE:
A
A
FLAT AREA
A A
Nose Landing GearInclined Blocks
FIGURE-02-30-01-991-022-A01
02-30-01Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_A
R_0
2300
1_1_
0230
101_
01_0
0
FO
RK
25.4
mm
MIN
CO
NT
OU
R O
F T
IRE
S O
N G
RO
UN
D
563 mm
927.
10 m
m
TW
IN W
HE
EL
TR
AC
K
6.5°
(22.16 in)
(36.
5 in
)
(1 in
)
655
mm
(25.
78 in
)JA
CK
ING
PO
INT
LH S
HO
WN
RH
SY
MM
ET
RIC
AL
(1 in
)25
.4 m
m M
IN25
.4 m
m (
1 in
)
Jacking for Wheel ChangeTwin Wheel Main Landing Gear (Sheet 1 of 2)
FIGURE-02-30-01-991-023-A01
02-30-01Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CA
NT
ILE
VE
R A
RM
CA
NT
ILE
VE
R A
RM
CO
NT
OU
R O
F T
IRE
S O
N G
RO
UN
D
FO
RK
(1 in
)(1
4.96
in)
(30.
70 in
)
(1 in
)
25.4
mm
380
mm
780
mm
25.4
mm
MIN
JAC
KIN
G P
OIN
TS
LH S
HO
WN
RH
SY
MM
ET
RIC
AL
N_A
R_0
2300
1_1_
0230
102_
01_0
0
(1 in
)25
.4 m
m M
IN
(14.
96 in
)38
0 m
m(1
in)
25.4
mm
Jacking for Wheel ChangeFour Wheel Bogie Main Landing Gear (Sheet 2 of 2)
FIGURE-02-30-01-991-023-A01
02-30-01Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
02-40-01 HEALTH AND SAFETY ISSUES
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 02-40-01-001-A01
General
1. The emphasis during all aircraft recovery operations is SAFETY. All necessary precautions must betaken to avoid injury to personnel and the occurrence of secondary damage to the aircraft. Not onlythe members of aircraft recovery team, but everyone at the incident site must know all the safetyissues as they evolve. A number of different factors must be taken into account to make sure thesafety issue is properly controlled.Make sure that adherence to a recovery close loop process is ensured to control and set up mitigationplan if needed. By definition this implies that recovery plan engineering, tooling capability andpersonnel qualification or expertise are correctly assessed.Paragraphs are not in order of importance.
A. CommunicationMake sure sufficient and correct communication equipment is available for communication atthe recovery site. Communication equipment can include two-way radios and cell phones. Voiceactivated, lightweight headsets with microphones are ideal for recovery operations. Extrabatteries or a power supply must be available.A direct link with the air traffic control service will most likely be required, depending on thelocation of the incident site. The main problem will be to cross active runways and taxiways inorder to access the incident or accident site. In most cases the local air traffic control servicewill provide an alternative access route to the site in order to reduce the amount ofcommunication.It is absolutely mandatory that lines of communication are established and kept open betweenall groups at the site, including the recovery team, fire department, Investigative Authority,police, airport personnel and any contracted assistance.Short briefing sessions must be held between all groups and parties involved with the recoveryprocess. These briefings will alert personnel to the upcoming steps, and to any possible hazardsand dangers.
B. PersonnelIt should be understood that the aircraft is by definition not under normal maintenance oroperational status. Therefore its recovery involves multiple personnel/parties competencies,which have not necessarily worked previously together and do not know each other’sconstraints-outcomes. As parties have incompatible goals it is of prime importance that therecovery manager ensure that information, caution, etc. are well understood and put in practiceby all.All personnel at the incident site must have proper and adequate personal protective clothingand equipment. This will change greatly if the existing climate and weather conditions change.Examples: Safety boots, personal breathing mask, rainwear, parkas and gloves, etc.
02-40-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Personnel must be kept at a safe distance during any leveling/lifting operation. The recoverymanager must make sure that the personnel knows the dangers of steel cable during pulling andwinching operations, as well as dangers arising due to the nature of the corrective actionsembodimentMake sure that everyone knows the dangers of going into, climbing-on or going below theaircraft until it is stable and or adequately shored.First-aid kits must be available at the site to cope with minor injuries. Detailed information onhow to contact and arrange for emergency medical attention must be available.
WARNING : MAKE SURE THAT THE AIRCRAFT IS CORRECTLY GROUNDED.
WARNING : MAKE SURE THAT THE AIRCRAFT ELECTRICAL NETWORK IS DE-ENERGIZEDBEFORE YOU DISCONNECT THE EXTERNAL POWER CONNECTOR. IF YOUDISCONNECT THE EXTERNAL POWER CONNECTOR WHEN THE ELECTRICALNETWORK IS ENERGIZED, DANGEROUS ARCING CAN OCCUR.
WARNING : OPEN, SAFETY/LOCK AND TAG THE CIRCUIT BREAKERS RELATED TO THEBLUE HYDRAULIC SYSTEM ELECTRIC PUMP. THIS PUMP RUNSAUTOMATICALLY WHEN THE AIRCRAFT ELECTRICAL NETWORK ISENERGIZED AND THE NLG LEG EXTENDED
CAUTION : MAKE SURE THAT THE AIRCRAFT ELECTRICAL NETWORK IS DE-ENERGIZEDBEFORE YOU DISCONNECT THE EXTERNAL POWER CONNECTOR. IF YOUDO NOT DO SO, THERE IS A RISK OF ARCING AND THIS CAN CAUSEDAMAGE TO THE AIRCRAFT.
C. Electrical SystemsIf you took the decision to leave the aircraft with the batteries connected, do an investigationbefore you energize the circuits. Leaving the batteries connected can help during the differentsteps of the recovery process.Before you use external aircraft power-supply to help the recovery operations, make sure thatthe systems are serviceable.If the aircraft structure is damaged, it is better to disconnect the batteries and not to tryenergize the aircraft with the external supply.
WARNING : MAKE SURE THAT YOU OBEY ALL THE APPLICABLE SAFETY PRECAUTIONSWHEN YOU WORK ON THE OXYGEN SYSTEM OR WITH OXYGEN EQUIPMENT.
D. Oxygen SystemsWhen the aircraft is stable and it is possible to get into the aircraft, make sure that the oxygenbottle valves in the cockpit and cabin are closed. If they are not, close them manually. Ifpossible, remove the bottles from the aircraft. Take the decision as to remove or secure theoxygen generators. As this is a time-consuming task, this decision will be based on the currentdangers involved, the condition of the aircraft and the time available.
02-40-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
WARNING : MAKE SURE THAT YOU OBEY ALL THE APPLICABLE SAFETY PRECAUTIONSWHEN YOU REMOVE FUEL OR WHEN YOU WORK IN AN ENVIRONMENTWHERE THERE IS FUEL.
WARNING : MAKE SURE THAT THE TANKER AND THE AIRCRAFT ARE CONNECTED TOAN APPROVED GROUND AND THAT ELECTRICAL BONDING BETWEEN THEAIRCRAFT AND THE TANKER IS CONNECTED. ONLY IF THESE CONDITIONSARE MET, YOU CAN CONNECT FUEL HOSES OR ADAPTERS BETWEEN THEAIRCRAFT AND THE FUEL TANKER.
E. DefuelingMake sure that only qualified and approved personnel is near the aircraft during the defuelprocess. Steps should be taken to have the Fire Department stand by until the end of thisprocess.If there is any sign of fuel leaks, a hazardous materials team must try to contain any fuelleakage.
F. EquipmentMake sure that contracted assistance, such as heavy-equipment operators, become part of thegroup safety team approach and are briefed on all relative safety issues. Keep in mind that mostheavy-equipment operators never worked near an aircraft. It is necessary give them relevantsafety issues. Discuss with these operators the concerns of overloading equipment and thesubsequent possible dangers. Most heavy-equipment operators know these concerns but not asthey relate to the aircraft. These discussions can include areas such as maximum lifting loadsduring crane lifts. Maximum jacking point loads and pneumatics lifting bags loading figures andcharts must be available.
G. Recovery OperationsMake sure that all equipment in use is properly rated for the loaded anticipated. Make sure thatthe aircraft is stable during all the recovery actions and that tooling used will not cause aircraftinstability. Adherence to maximum wind speeds is required during lifting and leveling operations.AIRBUS recommends that all loads imposed on the aircraft during a recovery operation must berecorded. If it is not possible to record the loads, record all the steps used to make sure that youdo not exceed maximum loads. This will have a direct impact on corrective actions to do forreturn to service.
02-40-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
WEIGHT AND CG MANAGEMENT
03-00-00 WEIGHT AND CG MANAGEMENT
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-00-00-558-801-A01
General
1. GeneralThe aim is to calculate the weight of the aircraft and the CG location in order to anticipate aircraftstability changes.The weight of the aircraft and the CG location are the basic data used to calculate the expectedloads and to select a recovery technique (selection of tooling and equipment).The choice of a leveling/lifting scenario (see TBD) and the use of the logic chart (see DESC09-20-01-002-A01) will help to control aircraft weight and CG.
2. InspectionsNot Applicable.
3. Job Setup ReferencesUse aircraft reference axes, glossary of terms (see 09-10-02) and the aircraft reference OEW or DOW.
A. Worksheet PrincipleThe worksheets are used to calculate the NRW and moments.Chapter 03-60-01 gives the source of the specific data used to complete the ”interimworksheets” and calculate the final NRW.The NRW and CG worksheet indicates in front of each item which ARM chapter will giverelevant data to allow completion of ”interim worksheets” and final NRW calculation.It is understood that NRW, CG position and calculation of expected loads will not be accurate ifgeneric data is used for the OEW, H-arm and Y-arm data.It should be noted that the OEW or DOW and the H-arm and Y-arm apply to a specific aircraftwith all landing gears extended, flight controls retracted and thrust reversers in stowed position.See DESC 09-50-01-001-A01 for the calculation worksheets.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-20-01-002-A01 DESC 09-20-01-002-A01-Aircraft Recovery Logic Chart
DESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets09-10-02 09-10-02-GLOSSARY OF TERMS03-60-01 03-60-01-REFERENCE FOR CALCULATION09-50-01 09-50-01-WEIGHT AND CG CALCULATION WORKSHEETSFIGURE 03-00-00-991-002-A FIGURE 03-00-00-991-002-A-CG Conversion Principle
FIGURE 03-00-00-991-002-B FIGURE 03-00-00-991-002-B-CG Conversion Principle
03-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
REFERENCE DESIGNATIONFIGURE 03-00-00-991-002-C FIGURE 03-00-00-991-002-C-CG Conversion Principle
FIGURE 03-00-00-991-002-D FIGURE 03-00-00-991-002-D-CG Conversion Principle
Referenced Information
TABLE 1
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
**ON A/C A318-100
Subtask 03-00-00-558-001-A01
A. CG Conversion Principle
(1) The CG location (in the longitudinal axis) can be expressed in % of the Reference Chord(%RC) or in lever arm distance (H-arm). See FIGURE 03-00-00-991-002-A.In this manual, the lever arm distance (H-arm and Y-arm) is used to calculate the CGlocation calculation.
(a) Use the formula that follows to convert the CG expressed in %RC from other manualsinto H-arm.- H-arm (in meters) = (%RC × 0.041935) + 15.4139- H-arm (in inches) = (%RC × 1.651) + 606.847
(b) Use the formula that follows to convert H-arm into %RC.- %RC = (H-arm -- 15.4139) / 0.041935 (H-arm in meters)
03-00-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
- %RC = (H-arm -- 606.847) / 1.651 (H-arm in inches)
**ON A/C A319-100
Subtask 03-00-00-558-001-B01
A. CG Conversion Principle
(1) The CG location (in the longitudinal axis) can be expressed in % of the Reference Chord(%RC) or in lever arm distance (H-arm). See FIGURE 03-00-00-991-002-B.In this manual, the lever arm distance (H-arm and Y-arm) is used to calculate the CGlocation calculation.
(a) Use the formula that follows to convert the CG expressed in %RC from other manualsinto H-arm.- H-arm (in meters) = (%RC × 0.041935) + 16.2016- H-arm (in inches) = (%RC × 1.651) + 637.858
(b) Use the formula that follows to convert H-arm into %RC.- %RC = (H-arm -- 16.2016) / 0.041935 (H-arm in meters)- %RC = (H-arm -- 637.858) / 1.651 (H-arm in inches)
**ON A/C A320-100 A320-200
Subtask 03-00-00-558-001-C01
A. CG Conversion Principle
(1) The CG location (in the longitudinal axis) can be expressed in % of the Reference Chord(%RC) or in lever arm distance (H-arm). See FIGURE 03-00-00-991-002-C.In this manual, the lever arm distance (H-arm and Y-arm) is used to calculate the CGlocation calculation.
(a) Use the formula that follows to convert the CG expressed in %RC from other manualsinto H-arm.- H-arm (in meters) = (%RC × 0.041935) + 17.8015- H-arm (in inches) = (%RC × 1.651) + 700.85
(b) Use the formula that follows to convert H-arm into %RC.- %RC = (H-arm -- 17.8015) / 0.041935 (H-arm in meters)- %RC = (H-arm -- 700.85) / 1.651 (H-arm in inches)
03-00-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
Subtask 03-00-00-558-001-D01
A. CG Conversion Principle
(1) The CG location (in the longitudinal axis) can be expressed in % of the Reference Chord(%RC) or in lever arm distance (H-arm). See FIGURE 03-00-00-991-002-D.In this manual, the lever arm distance (H-arm and Y-arm) is used to calculate the CGlocation calculation.
(a) Use the formula that follows to convert the CG expressed in %RC from other manualsinto H-arm.- H-arm (in meters) = (%RC × 0.041935) + 22.0687- H-arm (in inches) = (%RC × 1.651) + 868.85
(b) Use the formula that follows to convert H-arm into %RC.- %RC = (H-arm -- 22.0687) / 0.041935 (H-arm in meters)- %RC = (H-arm -- 868.85) / 1.651 (H-arm in inches)
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
Subtask 03-00-00-970-001-A01
B. Principle of the NRW and Related CG Position Calculation
NOTE : All calculations are based on OEW or DOW aircraft configuration and related CG. Theweight differences between the OEW or DOW and the real status of the aircraft arethen recorded on calculation worksheets. The data on these worksheets is used tocalculate the NRW and CG location of the aircraft.
(1) Find the weight and calculate the related H-arm moment of a known aircraft configuration(OEW or DOW).
NOTE : For the OEW or DOW configuration, the Y-arm = 0.
(2) Record the values on the NRW and CG worksheet (see 09-50-01) applicable to theconfiguration (OEW or DOW) that you will use for the calculation.
(3) For each item on the NRW and CG worksheet, use the related chapter and related interimworksheet to record the weight, the H-arm moment and the Y-arm moment of each itemwhich remains on the aircraft, which is removed or missing from the aircraft and which hasan effect on the known OEW or DOW.
NOTE : It is considered that the Y-arm of components located inside the fuselage isnegligible for the calculation made, therefore they are ignored.
NOTE : The ARM gives all necessary data (for each scenario) to allow completion ofinterim worksheet.
03-00-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(4) Use the ”NRW and Related H and Y Moment” worksheet (see 09-50-01) to find the NRW,the total H-arm moment and the total Y-arm moment.NET RECOVERABLE WEIGHT =TOTAL H-ARM MOMENT =TOTAL Y-ARM MOMENT =
(5) Divide the ”total H-arm moment” value by the NRW value to find the longitudinal CGposition (XG).(LONGITUDINAL CG POSITION) XG =
(6) Divide the ”total Y-arm moment value” by the NRW value to find the lateral CG position(YG).(LATERAL CG POSITION) YG =
03-00-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
2.54
0 m
(100
in)16
.462
m(6
48.1
1 in
)
RE
FE
RE
NC
E C
HO
RD
4.19
35 m
(16
5.10
in)
25%
RC
7.00
0 m
(275
.591
in)
FU
SE
LAG
ED
AT
UM
LIN
E
0
Z
X
H−ARM= 0
15.4
139
m(6
06.8
47 in
)
N_A
R_0
3000
0_1_
0020
101_
01_0
0
CG Conversion PrincipleReference Chord Data - A318
FIGURE-03-00-00-991-002-A01
03-00-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
2.54
0 m
(100
in)
17.2
50 m
(679
.13
in)
RE
FE
RE
NC
E C
HO
RD
4.19
35 m
(16
5.10
in)
25%
RC
7.00
0 m
(275
.591
in)F
US
ELA
GE
DA
TU
M L
INE
0
Z
X
H−ARM= 0
16.2
016
m(6
37.8
60 in
)
OP
TIO
NA
L
N_A
R_0
3000
0_1_
0020
201_
01_0
0
CG Conversion PrincipleReference Chord Data - A319
FIGURE-03-00-00-991-002-B01
03-00-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
2.54
0 m
(100
in)
18.8
50 m
(742
.13
in)
RE
FE
RE
NC
E C
HO
RD
4.19
35 m
(16
5.10
in)
25%
RC
7.00
0 m
(275
.591
in)
0
Z
X
H−ARM= 0
17.8
015
m(7
00.8
5 in
)
FU
SE
LAG
ED
AT
UM
LIN
E
N_A
R_0
3000
0_1_
0020
301_
01_0
0
CG Conversion PrincipleReference Chord Data - A320FIGURE-03-00-00-991-002-C01
03-00-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
2.54
0 m
(100
in)
23.1
17 m
(910
.12
in)
RE
FE
RE
NC
E C
HO
RD
4.19
35 m
(16
5.10
in)
25%
RC
7.00
0 m
(275
.591
in)
0Z
X
H−ARM= 0
FU
SE
LAG
ED
AT
UM
LIN
E
22.0
687
m(8
68.8
5 in
)
N_A
R_0
3000
0_1_
0020
401_
01_0
1
CG Conversion PrincipleReference Chord Data - A321
FIGURE-03-00-00-991-002-D01
03-00-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
03-20-01 FUEL LOAD AND CG CONTROL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 03-20-01-001-A01
General
1. To safely level or lift a damaged aircraft so that it can be moved on it’s own Landing Gear (or on asuitable ground equipment trailer) you must establish the weight and center of gravity (CG) of theaircraft.This chapter contains the method and calculations needed to establish the effect of the fuel load onthe position of the aircraft CG. The weight and CG positions of the aircraft will change due to thequantity of fuel in each tank. To find the changes in weight and CG position, calculate:- The H-arm dimension along the longitudinal plane from nose to tail
(H-arm is a dimension from the CG of an item/component to the horizontal reference datumplane)
- The Y-arm dimension along the lateral plane from wing tip to wing tip(Y-arm is a dimension from the CG of an item/component to the lateral arm reference datumplane).
The tables (see DESC 03-20-01-002-A01) in this chapter contain fuel weight and CG data forselected incremental fuel volumes for each fuel tank and for each scenario.
NOTE : Fuel density used in calculations is: 0.785 kg/liter and 1.7306138 lb/liter
03-20-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
AIR
CR
AF
TW
EIG
HT
CE
NT
ER
TA
NK
WE
IGH
T
OU
TE
R T
AN
KW
EIG
HT
INN
ER
TA
NK
WE
IGH
TO
UT
ER
TA
NK
WE
IGH
T
LIF
TIN
GLO
AD
CE
NT
ER
TA
NK
WE
IGH
T(I
F IN
ST
ALL
ED
)
AD
DIT
ION
AL
INN
ER
TA
NK
WE
IGH
T
MO
ME
NT
S T
AK
EN
AT
CO
NT
AC
T P
OIN
T
N_A
R_0
3200
1_1_
0010
101_
01_0
3
Aircraft LoadsType and Position of Loads Acting on the Aircraft
FIGURE-03-20-01-991-001-A01
03-20-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 03-20-01-002-A01
Tables
1. GeneralTo find the weight and associated CG of remaining fuel on board, you must know the quantity of fuelremaining in each tank. If you do not know the quantity of fuel remaining in each tank see 03-20-02for information about how to assess the fuel quantity without serviceable aircraft systems.Using the fuel quantity, you must determine the weight and moment (generated by H-arm and Y-arm) of the fuel, using the table for the given scenario.When you have found the data from the relevant tables, enter this data in the fuel remaining onboardeffect ’worksheet’ boxes (see DESC 09-50-01-001-A01 for calculation worksheets) with the weight,the H-arm moment and the Y-arm moment values for the remaining fuel in each tank.For information on defuel procedures see 05-10-00.
NOTE : The tables that follow give estimated values to help you estimate the CG position. Thevalues are calculated without any pitch or roll angle of the aircraft. Accurate data arerelated to your aircraft configuration.
**ON A/C A318-100
2. TablesThe table that follow gives the H-arm and Y-arm related to important fuel capacities.
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
15.4 m(606.30 in)
2418 kgm(209780 lb.in)
2.183 m(85.94 in)
343 kgm(29735 lb.in)
1/41800 l(476 US gal)
1413 kg(3115 lb)
15.386 m(605.75 in)
21740 kgm(1886911 lb.in)
2.775 m(109.25 in)
3921 kgm(340314 lb.in)
1/23400 l(898 US gal)
2669 kg(5884 lb)
15.489 m(609.80 in)
41340 kgm(3588063 lb.in)
3.151 m(124.06 in)
8410 kgm(729969 lb.in)
3/45200 l(1374 USgal)
4082 kg(8999 lb)
15.642 m(615.83 in)
63851 kgm(5541854 lb.in)
3.629 m(142.87 in)
14814 kgm(1285687 lb.in)
Full
6925 l(1829 USgal)
5436 kg(11984 lb)
16.012 m(630.39 in)
87043 kgm(7554594 in)
4.535 m(178.54 in)
24653 kgm(54347 lb.in)
Inner Cell
TABLE 1
03-20-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
1/4200 l(53 US gal)
157 kg(346 lb)
18.622 m(733.15 in)
2924 kgm(253.670 lb.in)
10.502 m(413.46 in)
1649 kgm(143057 lb.in)
1/2400 l(106 US gal)
314 kg(692 lb)
18.706 m(736.46 in)
5874 kgm(509630 lb.in)
10.751 m(423.27 in)
3376 kgm(292903 lb.in)
3/4600 l(159 US gal)
471 kg(1038 lb)
18.786 m(739.61 in)
8848 kgm(767715 lb.in)
10.966 m(431.73 in)
5165 kgm(448136 lb.in)
Full880 l(232 US gal)
691 kg(1523 lb)
18.943 m(745.79 in)
13086 kgm(1135838 lb.in)
11.364 m(447.40 in)
7850 kgm(681390 lb.in)
Outer Cell
TABLE 2
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
15.47 m(609.06 in)
2429 kgm(210735 lb.in)
- -
1/42200 l(581 US gal)
1727 kg(3807 lb)
15.195 m(598.23 in)
26242 kgm(2277462 lb.in)
- -
1/24200 l(1110 USgal)
3297 kg(7269 lb)
15.053 m(592.64 in)
49630 kgm(4307900 lb.in)
- -
3/46200 l(1638 USgal
4867 kg(10730 lb)
15.005 m(590.75 in)
73029 kgm(6338748 lb.in)
- -
Full
8250 l(2179 USgal)
6476 kg(14277 lb)
14.968 m(589.29 in)
96937 kgm(8413293 lb.in)
- -
Center Tank
TABLE 3
**ON A/C A319-100
3. TablesThe table that follow gives the H-arm and Y-arm related to important fuel capacities.
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
16.188 m(637.32 in)
2542 kgm(220513 lb.in)
2.183 m(85.94 in)
343 kgm(29735 lb.in)
1/42000 kg(4409 lb)
1570 kg(3461 lb)
16.187 m(637.28 in)
25414 kgm(2205626 lb.in)
2.827 m(111.30 in)
4438 kgm(385209 lb.in)
03-20-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
1/23600 kg(7937 lb)
2826 kg(6230 lb)
16.291 m(641.38 in)
46038 kgm(3995797)
3.194 m(125.75 in)
9026 kgm(783423 lb.in)
3/45200 l(1374 USgal)
4082 kg(8999 lb)
16.43 m(646.85 in)
67067 kgm(5821003 lb.in)
3.629 m(142.87 in)
14814 kgm(1285687 lb.in)
Full
6925 l(1829 USgal)
5436 kg(11984 lb)
16.8 m(661.42 in)
91325 kgm(7926457 lb.in)
4.535 m(178.54 in)
24652(2139623 lb.in)
Inner Cell
TABLE 4
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
1/4200 l(53 US gal)
157 kg(346 lb)
19.41 m(764.17 in)
3047 kgm(264403 lb.in)
10.502 m(413.46 in)
1649 kgm(143057 lb.in)
1/2400 l(106 US gal)
314 kg(692 lb)
19.494 m(767.48 in)
6121 kgm(531096 lb.in)
10.751 m(423.27 in)
3376 kgm(292903 lb.in)
3/4600 l(159 US gal)
471 kg(1038 lb)
19.574 m(770.63 in)
9219 kgm(799914 lb.in)
10.966 m(431.73 in)
5165 kgm(448136 lb.in)
Full880 l(232 US gal)
691 kg(1523 lb)
19.731 m(776.81 in)
13634 kgm(1183082 lb.in)
11.364 m(447.40 in)
7853 kgm(681390 lb.in)
Outer Cell
TABLE 5
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
16.258 m(640.08 in)
2553 kgm(221468 lb.in)
- -
1/42200 l(581 US gal)
1727 kg(3807 lb)
15.959 m(628.31 in)
27561 kgm(2391976 lb.in)
- -
1/24200 l(1110 USgal)
3297 kg(7269 lb)
15.834 m(623.39 in)
52205 kgm(4531422 lb.in)
- -
3/46200 l(1638 USgal)
4867 kg(10730 lb)
15.79 m(621.65 in)
76850 kgm(6670305 lb.in)
- -
03-20-01Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
Full
8250 l(2179 USgal)
6476 kg(14277 lb)
15.756 m(620.31 in)
102036 kgm(8856166 lb.in)
- -
Center Tank
TABLE 6
**ON A/C A320-100 A320-200
4. TablesThe table that follow gives the H-arm and Y-arm related to important fuel capacities.
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
17.79 m(700.39 in)
2793 kgm(242335 lb.in)
2.179 m(85.79 in)
342 kgm(29683 lb.in)
1/42000 kg(4409 lb)
1570 kg(3461 lb)
17.784 m(700.16 in)
27921 kgm(2423254 lb.in)
2.815 m(110.83 in)
4420 kgm(383583 lb.in)
1/23600 kg(7937 lb)
2826 kg(6230 lb)
17.885 m(704.13 in)
50543 kgm(4386730 lb.in)
3.175 m(125.00 in)
8973 kgm(778750 lb.in)
3/45200 l(1374 USgal)
4867 kg(10730 lb)
18.012 m(709.13 in)
73525 kgm(7608965 lb.in)
3.579 m(140.91 in)
14609 kgm(1511964 lb.in)
Full
6984 l(1845 USgal)
5482 kg(12086 lb)
18.372 m(723.31 in)
100715 kgm(8741925 lb.in)
4.469 m(175.94 in)
24499 kgm(2126411 lb.in)
Inner Cell
TABLE 7
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
1/4200 l(53 US gal)
157 kg(346 lb)
21.01 m(827.17 in)
3299 kgm(286201 lb.in)
10.502 m(413.46 in)
1649 kgm(143057 lb.in)
1/2400 l(106 US gal)
314 kg(692 lb)
21.094 m(830.47 in)
6624 kgm(574685 lb.in)
10.751 m(423.27 in)
3376 kgm(292972 lb.in)
3/4600 l(159 US gal)
471 kg(1038 lb)
21.174 m(833.62 in)
9973 kgm(865298 lb.in)
10.966 m(431.73 in)
5165 kgm(448136 lb.in)
03-20-01Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
Full880 l(232 US gal)
691 kg(1523 lb)
21.331 m(839.80 in)
14740 kgm(1279015 lb.in)
11.364 m(447.40 in)
7853 kgm(681390 lb.in)
Outer Cell
TABLE 8
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
17.858 m(703.07 in)
2804 kgm(243262 lb.in)
- -
1/42200 l(581 US gal)
1727 kg(3807 lb)
17.559 m(691.30 in)
30324 kgm(2631779 lb.in)
- -
1/24200 l(1110 USgal)
3297 kg(7269 lb)
17.434 m(686.38 in)
57480 kgm(4989296 lb.in)
- -
3/46200 l(1638 USgal)
4867 kg(10730 lb)
17.39 m(684.65 in)
84637 kgm(7346295 lb.in)
- -
Full
8250 l(2179 USgal)
6476 kg(14277 lb)
17.362 m(683.54 in)
110092 kgm(9758901 lb.in)
- -
Center Tank (A320-200 only)
TABLE 9
**ON A/C A321-100 A321-200
5. TablesThe table that follow gives the H-arm and Y-arm related to important fuel capacities.
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
22.056 m(868.35 in)
3463 kgm(300449 lb.in)
2.181 m(85.87 in)
342 kgm(29711 lb.in)
1/42000 l(528 US gal)
1570 kg(3461 lb)
22.039 m(867.68 in)
34601 kgm(3003041 lb.in)
2.789 m(109.80 in)
4379 kgm(380018 lb.in)
1/24000 l(1057 USgal)
3140 kg(6923 lb)
22.174 m(872.99 in)
69626 kgm(6043710 lb.in)
3.204 m(126.14 in)
10061 kgm(873267 lb.in)
3/46000 l(1585 USgal)
4710 kg(10384 lb)
22.43 m(883.07 in)
105645 kgm(9169799 lb.in)
3.9 m(153.54 in)
18369 kgm(1594359 lb.in)
03-20-01Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
Full
7745 l(2046 USgal)
6080 kg(13404 lb)
22.883 m(900.91 in)
139129 kgm(12.075768 lb.in)
4.973 m(195.79 in)
30236 kgm(2624369 lb.in)
Wing Tank
TABLE 10
Capacity Weight H-arm Harm Moment Y-arm Y-arm Moment
200 l(53 US gal)
157 kg(346 lb)
22.069 m(868.86 in)
3465 kgm(300626 lb.in)
- -
1/42000 l(528 US gal)
1570 kg(3461 lb)
21.785 m(857.68 in)
34202 kgm(2968431 lb.in)
- -
1/24000 l(1057 USgal)
3140 kg(6923 lb)
21.672 m(853.23 in)
68050 kgm(5906911 lb.in)
- -
3/46000 l(1585 USgal)
4710 kg(10384 lb)
21.634 m(851.73 in)
101896 kgm(8844364 lb.in)
- -
Full
8210 l(2169 USgal)
6445 kg(14209 lb)
21.596 m(850.24 in)
139186 kgm(12081060 lb.in)
- -
Center Tank
TABLE 11
03-20-01Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
03-20-02 MANUAL FUEL QUANTITY INDICATION
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-20-02-970-801-A01
Use of Magnetic Level Indicators (MLI)
1. GeneralThe Magnetic Level Indicators (MLI) are used on ground to calculate the fuel quantity in the wingand center tanks.See AMM 12-11-28-650-007 for detailed procedure.This procedure is valid only when the aircraft attitude is between minus 1.5˚ and plus 1.5˚ roll andminus 1.5˚ and plus 1.5˚ pitch.
2. InspectionsNot Applicable
3. Job Setup ReferencesOn A318, A319 and A320, there are five MLI in each wing tank and one in the center tank.On A321, there are seven MLI in each wing tank and one in the center tank.See FIGURE 03-20-02-991-001-AFIGURE 03-20-02-991-001-B.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATION98A28104000000 PURGER WATER DRAIN
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONAMM 12-11-28-650-007AMM 12-11-28-650-001AMM 12-11-28-650-002AMM 12-32-28-281-001FIGURE 03-20-02-991-001-A FIGURE 03-20-02-991-001-A-Magnetic Level Indicators
FIGURE 03-20-02-991-001-B FIGURE 03-20-02-991-001-B-Magnetic Level Indicators
FIGURE 03-20-02-991-002-A FIGURE 03-20-02-991-002-A-Attitude Monitor
Referenced Information
TABLE 2
03-20-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
WARNING : THIS PROCEDURE IS FOR INFORMATION ONLY TO HELP YOU PREPARE THERECOVERY OPERATION. TO DO THE PROCEDURE, YOU MUST REFER TO THEOPERATORS CUSTOMIZED DOCUMENTATION.
WARNING : MAKE SURE THAT YOU OBEY ALL THE APPLICABLE SAFETY PRECAUTIONSWHEN YOU REMOVE FUEL OR WHEN YOU WORK IN AN ENVIRONMENTWHERE THERE IS FUEL.
CAUTION : DO NOT LET THE MLI’S FALL FREELY.
CAUTION : RETRACT THE MLI’S AS SOON AS POSSIBLE. YOU CAN EASILY CAUSEDAMAGE TO AN EXTENDED MLI.
Subtask 03-20-02-869-001-A01
A. Preparation
(1) Safety Precaution
(a) You must obey the refuel/defuel safety precautions. See AMM 12-11-28-650-001 andAMM 12-11-28-650-002.
(b) Put the safety barriers in position.
(2) Fuel Sampling
(a) Use the 98A28104000000 PURGER WATER DRAIN to get a fuel sample from theaircraft. See AMM 12-32-28-281-001.
(b) Measure the Specific Gravity (SG) of the fuel sample.
(3) Get Access
(a) Put an access platform below the applicable MLI.
(b) Open the access door 192MB, see FIGURE 03-20-02-991-002-A.
(4) Aircraft Attitude
(a) Find and write down the aircraft attitude (pitch and roll). See TBD.
(b) Or, if installed, read the aircraft attitude shown by the bubble on the attitudemonitor, see FIGURE 03-20-02-991-002-A.See TABLE 3 to convert the attitude angles and grid square letters on the attitudemonitor.
Pitch Ref Roll Ref- 1.5˚ 1 - 1.5˚ A- 1.0˚ 2 - 1.0˚ B- 0.5˚ 3 - 0.5˚ C0.0˚ 4 0.0˚ D
03-20-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Pitch Ref Roll Ref+ 0.5˚ 5 + 0.5˚ E
+ 1.0˚ 6 + 1.0˚ F
+ 1.5˚ 7 + 1.5˚ G
Aircraft Attitude
TABLE 3
Subtask 03-20-02-970-001-A01
B. Use of the Magnetic Level Indicators (MLI)
(1) Use a screwdriver to push the applicable MLI and turn it through 90 deg.
(2) Hold and carefully lower the MLI fully. Then carefully lift the MLI until you feel themagnets engage.
(3) Read the units mark nearest to the bottom-skin of the wing and write down the number.
(4) Retract the MLI and use a screwdriver to turn it through 90 deg. to lock it.
(5) Find the volume of fuel in each tank:
(a) Use the applicable MLI stick number and the applicable aircraft attitude grid-squareletter to find the corresponding fuel quantity table. See AMM 12-11-28-650-007 forthe fuel quantity tables.
(b) Find the applicable MLI unit number row and the applicable A/C attitude (grid-square letter and number) in the table.Find the intersection of the applicable rows to give the correct volume of fuel in thetank.
(c) Multiply the total volume of the fuel by the specific gravity (SG) of the fuel to obtainthe mass of the fuel.
NOTE : The MLI are accurate to +/- 5 % of their indication.
03-20-02Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200
N_AR_032002_1_0010101_01_00
RIB2
RIB6
RIB10
RIB12
RIB21
CL
CTRSTICK
STICK No 1 STICK No 2
EXTERNAL VIEW OF RETRACTEDAND LOCKED M.L.I.
INDICATOR ROD EXTENDED
STICK No 3
STICK No 4STICK No 5
Magnetic Level IndicatorsLocation - A318/A319/A320
FIGURE-03-20-02-991-001-A01
03-20-02Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
EXTERNAL VIEW OF RETRACTEDAND LOCKED M.L.I.
INDICATOR ROD EXTENDED
N_AR_032002_1_0010201_01_00
RIB2
RIB6
RIB10
RIB12
RIB21
CL
CTRSTICK
STICK No 1 STICK No 2STICK No 3
STICK No 4
STICK No 7STICK No 5
STICK No 6
Magnetic Level IndicatorsLocation - A321
FIGURE-03-20-02-991-001-B01
03-20-02Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_032002_1_0020101_01_00
A
192MB
ATTITUDE MONITOR
A1BCDEFG
2 3 4 5 6 7
A
39QM
Attitude MonitorLocation
FIGURE-03-20-02-991-002-A01
03-20-02Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
03-50-01 MANAGING AIRCRAFT WEIGHT AND CG
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 03-50-01-001-A01
Introduction
1. GeneralManagement of the aircraft weight and related CG is one of the key issues of the recovery plan andoperation. It has a direct impact on aircraft stability, calculation of expected loads and the loadsrecorded for a given recovery process.
2. PurposeFor a given aircraft attitude (See TBD), it is necessary first to calculate the aircraft NRW and CG(See 03-00-00) to make the calculations of the expected loads, based on the leveling/liftingtechniques that will be used.These expected loads, and then the applied loads must be in the limits that follow:- Aircraft allowable loads,- Tooling capabilities.If these loads are not in the limits, it will be necessary:- To find an alternative leveling/lifting procedure to make sure that the aircraft, tooling and
equipment support loads are not more than the allowable loads,- To manage aircraft weight and related CG to bring the expected loads in the allowable loads,- To use other tooling, if the tool cannot support the expected loads.
NOTE : The tooling should not only be able to support expected loads, but should also beappropriate for the travel range, arc movement, aircraft stability, ground stability, etc.…
NOTE : It is important to make sure that the aircraft is stable before and during theimplementation of the recovery phase/steps.
The installation of ballast or the removal of equipment, payload, fuel, etc. can help to change theaircraft weight and CG location.Every effort should be made to reduce the Total Weight of the aircraft to the minimum possible byremoval of significant amounts of payload. The easiest way to remove quickly large amounts ofweight can be fuel and cargo removal.In some cases, it may be necessary to remove major aircraft components that are damaged. Beforeremoval of these components, it is important to do a careful study because it may be better to securethem in place temporarily.Galley catering units (trolleys, etc.) have a significant weight and every effort should be made toremove them. If they remain on board, carefully evaluate their weight when you make the H-armcalculations.Food in the catering units can deteriorate quickly. During a long recovery operation, it may become apriority to remove the catering units for health reasons.Draining of potable water and lavatory waste and removal of the escape slides and slide rafts can alsoreduce the weight.
03-50-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
It is not necessary to drain the fluids, such as hydraulic fluid, from closed systems unless there issignificant leakage that it is not possible to contain.As every aircraft recovery is different, it will be necessary to decide what and how much must beremoved. These decisions will be based on access, time, cost and the actual ability to do the task.The records made during the damage survey of the aircraft should include all major components thatare missing or that it is necessary to remove because of damage. It is necessary to include the weightchanges related to these components in the calculation of the aircraft weight and CG location.Removal of any aircraft components and equipment should be done in accordance with the AircraftMaintenance Manual (AMM), and recorded with the data collected during the aircraft survey.
3. Calculation IterationThe calculation iteration from NRW and CG up to expected loads, travel range, arc movement shouldbe continued until aircraft stability, expected loads, travel range, arc movement etc.… are in theacceptable limits.Changes to the different inputs used in the calculations can help to get satisfactory value related tothe settings of a recovery scenario.
4. List of Item Used for NRW and CG CalculationSee the related topic or task for the related item weight input.
Weight Inputs See
OEW 03-00-00DOW 03-00-00Fuel Remaining on Board Effect 03-20-01
Cargo and Baggage Remaining Effect TASK 03-50-01-558-801-A01TASK 03-50-01-558-801-B01TASK 03-50-01-558-801-C01TASK 03-50-01-558-801-D01
Total Traffic Load Remaining Effect TASK 03-50-01-558-802-A01
Ballast Added Effect TASK 03-50-01-558-803-A01Waste Water Remaining Effect TASK 03-50-01-558-804-A01
Non OEW Catering Equipment Added Effect TASK 03-50-01-558-805-A01
Large Component Movement Effect TASK 03-50-01-558-811-A01TASK 03-50-01-558-811-B01TASK 03-50-01-558-811-C01
Potable Water Removed Effect TASK 03-50-01-558-806-A01Cockpit and Cabin Crew Removed Effect TASK 03-50-01-558-807-A01
Catering Equipment Removed Effect TASK 03-50-01-558-808-A01
03-50-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Weight Inputs See
Large Component Removed /Missing Effect TASK 03-50-01-558-810-A01TASK 03-50-01-558-810-B01TASK 03-50-01-558-810-C01TASK 03-50-01-558-810-D01
Hydraulic Fluids Removed Effect TASK 03-50-01-558-809-A01
List of Item Used for NRW and CG Calculation
TABLE 1
03-50-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
TASK 03-50-01-558-801-A01
Cargo and Baggage Remaining Effect
1. GeneralThe aircraft has three cargo compartments.- The FWD cargo compartment (N˚1) in zone 130,- The aft cargo compartment (N˚4) in zone 150,- The bulk cargo compartment (N˚5) in zone 160.
NOTE : For location see 09-10-14
2. InspectionsNot Applicable.
3. Job Setup ReferencesThe tables that follow are built with a standard configuration. If the cargo compartments contain adifferent configuration, use the value given in the standard combination or in your WBM to find theapplicable H-arm and Y-arm.
A. Forward Cargo CompartmentThe forward cargo compartment is designed for the transport of bulk cargo and baggage.See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
1124A to 28
10.430 m(410.63 in)
1228 to 34
11.748 m(462.52 in)
Total24A to 34
11.078 m(436.14 in)
FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 1
B. Aft Lower Cargo CompartmentThe aft cargo compartment is designed for the transport of bulk cargo and baggage.See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-Arm Moment to add
4147/54 to 57
19.698 m(775.51 in)
03-50-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Section Frame Station RemainingWeight
Average H-Arm Moment to add
4257 to 60
21.374 m(841.50 in)
Total47/54 to 60
20.498 m(807.01 in)
FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 2
C. Bulk Cargo CompartmentThe aft cargo compartment is designed for the transport of bulk cargo and baggage.See your WBM to determine applicable Y-arm.
Section Frame StationRemaining
WeightAverage H-Arm Moment to add
5160 to 62
22.708 m(894.02 in)
5162 to 65
24.062 m(947.32 in)
Total60 to 65
23.528 m(926.30 in)
FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 3
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets09-10-14 09-10-14-CARGO COMPARTMENTS
Referenced Information
TABLE 4
03-50-01Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : IF CARGO AND BAGGAGE ARE NOT - OR CANNOT BE - REMOVED, MAKESURE THAT THEY ARE SAFELY FASTENED AND THAT LOADS ARE ASSYMMETRICAL AS POSSIBLE BEFORE YOU START THE RECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-001-A01
A. How to Find the Effect of Cargo and Baggage Remaining
(1) Use the tables in Job Setup References to determine H-arm moments and Y-arm momentsby reporting the masses of each container or pallet.
(2) Record the calculated values on FWD Cargo Compartment (in Zone 130) , Aft CargoCompartment (in Zone 150) , Bulk Cargo Compartment (in Zone 160) into boxes of theCargo and Baggage Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
TASK 03-50-01-558-801-B01
Cargo and Baggage Remaining Effect
1. GeneralThe aircraft has two cargo compartments.- The FWD cargo compartment (N˚1) in zone 130,- The aft cargo compartment (N˚4) in zone 150 and the aft cargo compartment (N˚5) in zone
160.
NOTE : For location see 09-10-14
2. InspectionsNot Applicable.
3. Job Setup ReferencesThe tables that follow are built with a standard configuration. If the cargo compartments contain adifferent configuration, use the value given in the standard combination or in your WBM to find theapplicable H-arm and Y-arm.
A. Forward Cargo CompartmentThe forward cargo compartment is designed for the transport of bulk cargo and baggage or thefollowing unit load devices:- 2 x half size containers LD3-46 (NAS 3610-2K2C, IATA contour AKG)- 2 x full size containers LD3-46W (NAS 3610-2K2C, IATA contour AKH)- 2 x 60.4x61.5 in pallets LD3-46P (NAS 3610-2K3P)See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
1124A to 28
10.744 m(422.99 in)
1228 to 34
12.371 m(487.05 in)
Total24A to 34
11.436 m(450.24 in)
Bulk Cargo in FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 1
Position ULD Remaining Weight Average H-Arm Moment to add
11 10.700 m(421.26 in)
03-50-01Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position ULD Remaining Weight Average H-Arm Moment to add
12 12.272 m(483.15 in)
Containers and Pallets in FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 2
B. Aft Cargo Compartment n˚4The aft cargo compartment n˚4 is designed for the transport of bulk cargo and baggage or thefollowing unit load devices:- 2 x half size containers LD3-46 (NAS 3610-2K2C, IATA contour AKG)- 2 x full size containers LD3-46W (NAS 3610-2K2C, IATA contour AKH)- 2 x 60.4x61.5 in pallets LD3-46P (NAS 3610-2K3P)See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
4147/51 to 54
20.485 m(806.50 in)
4254 to 59
22.695 m(893.50 in)
Total47/51 to 59
21.819 m(859.02 in)
Bulk Cargo in Aft Cargo Compartment Remaining Weight and Related H-arm
TABLE 3
Position ULD Remaining Weight Average H-Arm Moment to add
41 20.475 m(806.10 in)
42 22.047 m(867.99 in)
Containers and Pallets in Aft Cargo Compartment Remaining Weight and Related H-arm
TABLE 4
C. Aft Cargo Compartment n˚5The aft cargo compartment n˚5 is designed for the transport of bulk cargo and baggage.See your WBM to determine applicable Y-arm.
03-50-01Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Section Frame Station RemainingWeight
Average H-ArmMoment to add
5159 to 65
25.649 m(1009.80 in)
Bulk Cargo in Aft Cargo Compartment Remaining Weight and Related H-arm
TABLE 5
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets09-10-14 09-10-14-CARGO COMPARTMENTS
Referenced Information
TABLE 6
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : IF CARGO AND BAGGAGE ARE NOT - OR CANNOT BE - REMOVED, MAKESURE THAT THEY ARE SAFELY FASTENED AND THAT LOADS ARE ASSYMMETRICAL AS POSSIBLE BEFORE YOU START THE RECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
03-50-01Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 03-50-01-558-018-A01
A. How to Find the Effect of Cargo and Baggage Remaining
(1) Use the tables in Job Setup References to determine H-arm moments and Y-arm momentsby reporting the masses of each container or pallet.
(2) Record the calculated values on FWD Cargo Compartment (in Zone 130) , Aft CargoCompartment (in Zone 150) , Aft Cargo Compartment (in Zone 160) into boxes of theCargo and Baggage Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N_AR_035001_1_0030101_01_00
1.430 m(56.30 in)
2.630 m(103.54 in)
1.21
3 m
(47.
76 in
)0.
051
m(2
.00
in)
IATA CODEAKG
1.16
8 m
(46.
60 in
)
2.451 m(96.50 in)
1.562 m(61.50 in)
1.534 m(60.40 in)
NAS 3610−2K2CLD3−46IATA CODE AKG
2.007 m(79.00 in)
1.534 m(60.40 in)
1.562 m(61.50 in)
IATA CODEAKH
NAS 3610−2K2CLD3−46WIATA CODE AKH
1.562 m(61.50 in)
1.534 m
(60.40 in)
1.16
8 m
(46.
60 in
)
1.16
8 m
(46.
60 in
)
PALLETNAS 3610−2K3PLD3−46P
FWDCARGODOOR
11 12
FR24 FR34
A
A
FWD Cargo Compartment ArrangementPallets and Containers
FIGURE-03-50-01-991-003-A01
03-50-01Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N_AR_035001_1_0040101_01_00
FWDCARGODOOR
41 42
1.430 m(56.30 in)
2.630 m(103.54 in)
1.21
3 m
(47.
76 in
)0.
051
m(2
.00
in)
FR59FR47/51
A
IATA CODEAKG
1.16
8 m
(46.
60 in
)
2.451 m(96.50 in)
1.562 m(61.50 in)
1.534 m(60.40 in)
NAS 3610−2K2CLD3−46IATA CODE AKG
2.007 m(79.00 in)
1.534 m(60.40 in)
1.562 m(61.50 in)
IATA CODEAKH
NAS 3610−2K2CLD3−46WIATA CODE AKH
1.562 m(61.50 in)
1.534 m
(60.40 in)
1.16
8 m
(46.
60 in
)
1.16
8 m
(46.
60 in
)
PALLETNAS 3610−2K3PLD3−46P
A
Aft Cargo Compartment ArrangementPallets and Containers
FIGURE-03-50-01-991-004-A01
03-50-01Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
TASK 03-50-01-558-801-C01
Cargo and Baggage Remaining Effect
1. GeneralThe aircraft has three cargo compartments.- The FWD cargo compartment (N˚1) in zone 130,- The aft cargo compartment (N˚4) in zone 150,- The bulk cargo compartment (N˚5) in zone 160.
NOTE : For location see 09-10-14
2. InspectionsNot Applicable.
3. Job Setup ReferencesThe tables that follow are built with a standard configuration. If the cargo compartments contain adifferent configuration, use the value given in the standard combination or in your WBM to find theapplicable H-arm and Y-arm.
A. Forward Cargo CompartmentThe forward cargo compartment is designed for the transport of bulk cargo and baggage or thefollowing unit load devices:- 3 x half size containers LD3-46 (NAS 3610-2K2C, IATA contour AKG)- 3 x full size containers LD3-46W (NAS 3610-2K2C, IATA contour AKH)- 3 x rectangular container LD3-46R (NAS 3610-2K2C, IATA contour AKJ)- 3 x 60.4x61.5 in pallets LD3-46P (NAS 3610-2K3P)See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
1124A to 28
10.744 m(422.99 in)
1228 to 31
12.433 m(489.49 in)
1331 to 34
13.971 m(550.04 in)
Total24A to 34
12.283 m(483.58 in)
Bulk Cargo in FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 1
03-50-01Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position ULD Remaining Weight Average H-Arm Moment to add
11 10.700 m(421.26 in)
12 12.272 m(483.15 in)
13 13.844 m(545.04 in)
Containers and Pallets in FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 2
B. Aft Lower Cargo CompartmentThe forward cargo compartment is designed for the transport of bulk cargo and baggage or thefollowing unit load devices:- 3 x half size containers LD3-46 (NAS 3610-2K2C, IATA contour AKG)- 3 x full size containers LD3-46W (NAS 3610-2K2C, IATA contour AKH)- 3 x rectangular container LD3-46R (NAS 3610-2K2C, IATA contour AKJ)- 3 x 60.4x61.5 in pallets LD3-46P (NAS 3610-2K3P)See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
4147 to 50
22.085 m(869.49 in)
4250 to 52A/53
23.762 m(935.51 in)
4353 to 56
25.362 m(998.50 in)
4456 to 59
26.962 m(1061.50 in)
Total47 to 59
27.762 m(1092.99 in)
Bulk Cargo in Aft Cargo Compartment Remaining Weight and Related H-arm
TABLE 3
Position ULD Remaining Weight Average H-Arm Moment to add
41 22.084 m(869.45 in)
42 23.656 m(931.34 in)
03-50-01Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position ULD Remaining Weight Average H-Arm Moment to add
43 25.229 m(993.27 in)
44 26.801 m(1055.16 in)
Containers and Pallets in Aft Cargo Compartment Remaining Weight and Related H-arm
TABLE 4
C. Bulk Cargo CompartmentThe aft cargo compartment is designed for the transport of bulk cargo and baggage.See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
5159 to 60
28.029 m(1103.50 in)
5260 to 62
28.829 m(1135.00 in)
5362 to 65
30.182 m(1188.27 in)
Total59 to 65
29.382 m(1156.77 in)
Bulk Cargo in Aft Cargo Compartment Remaining Weight and Related H-arm
TABLE 5
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets09-10-14 09-10-14-CARGO COMPARTMENTS
Referenced Information
TABLE 6
03-50-01Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : IF CARGO AND BAGGAGE ARE NOT - OR CANNOT BE - REMOVED, MAKESURE THAT THEY ARE SAFELY FASTENED AND THAT LOADS ARE ASSYMMETRICAL AS POSSIBLE BEFORE YOU START THE RECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-019-A01
A. How to Find the Effect of Cargo and Baggage Remaining
(1) Use the tables in Job Setup References to determine H-arm moments and Y-arm momentsby reporting the masses of each container or pallet.
(2) Record the calculated values on FWD Cargo Compartment (in Zone 130) , Aft CargoCompartment (in Zone 150) , Bulk Cargo Compartment (in Zone 160) into boxes of theCargo and Baggage Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
FWDCARGODOOR
11 12
1.430 m(56.30 in)
2.630 m(103.54 in)
1.21
3 m
(47.
76 in
)0.
051
m(2
.00
in)
1.16
8 m
(46.
60 in
)
2.451 m(96.50 in)
1.562 m(61.50 in)
1.534 m(60.40 in)
CONTAINERSLD3−46
2.007 m(79.00 in)
1.534 m(60.40 in)
1.562 m(61.50 in)
CONTAINERSLD3−46W
1.562 m(61.50 in)
1.534 m
(60.40 in)
1.16
8 m
(46.
60 in
)
1.16
8 m
(46.
60 in
)
PALLET60.4 x 41.5 in
1.562 m(61.50 in)
1.534 m
(60.40 in)
1.16
8 m
(46.
60 in
)
CONTAINERSLD3−46R
13
FR24A FR34
A
N_AR_035001_1_0050101_01_00
A
FWD Cargo Compartment ArrangementPallets and Containers
FIGURE-03-50-01-991-005-A01
03-50-01Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
FWDCARGODOOR
41 42
1.430 m(56.30 in)
2.630 m(103.54 in)
1.21
3 m
(47.
76 in
)0.
051
m(2
.00
in)
1.16
8 m
(46.
60 in
)
2.451 m(96.50 in)
1.562 m(61.50 in)
1.534 m(60.40 in)
CONTAINERSLD3−46
2.007 m(79.00 in)
1.534 m(60.40 in)
1.562 m(61.50 in)
CONTAINERSLD3−46W
1.562 m(61.50 in)
1.534 m
(60.40 in)
1.16
8 m
(46.
60 in
)
1.16
8 m
(46.
60 in
)
PALLET60.4 x 41.5 in
1.562 m(61.50 in)
1.534 m
(60.40 in)
1.16
8 m
(46.
60 in
)
CONTAINERSLD3−46R
43 44
FR47 FR59
A
A
N_AR_035001_1_0060101_01_00
Aft Cargo Compartment ArrangementPallets and Containers
FIGURE-03-50-01-991-006-A01
03-50-01Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
TASK 03-50-01-558-801-D01
Cargo and Baggage Remaining Effect
1. GeneralThe aircraft has three cargo compartments.- The FWD cargo compartment (N˚1 and 2) in zone 130,- The aft cargo compartment (N˚ 3 and 4) in zone 150,- The bulk cargo compartment (N˚5) in zone 160.
NOTE : For location see 09-10-14
2. InspectionsNot Applicable.
3. Job Setup ReferencesThe tables that follow are built with a standard configuration. If the cargo compartments contain adifferent configuration, use the value given in the standard combination or in your WBM to find theapplicable H-arm and Y-arm.
A. Forward Cargo CompartmentThe forward cargo compartment is designed for the transport of bulk cargo and baggage or thefollowing unit load devices:- 5 x half size containers LD3-46 (NAS 3610-2K2C, IATA contour AKG)- 5 x full size containers LD3-46W (NAS 3610-2K2C, IATA contour AKH)- 5 x 60.4x61.5 in pallets LD3-46P (NAS 3610-2K3P)See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
1124A to 28
10.744 m(422.99 in)
1228 to 31
12.433 m(489.49 in)
2131 to 34
14.034 m(552.52 in)
2234 to 35.2
15.634 m(615.51 in)
2335.2 to 35.5
17.712 m(697.32 in)
03-50-01Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Section Frame Station RemainingWeight
Average H-ArmMoment to add
Total24A to 35.5
13.883 m(546.57 in)
Bulk Cargo in FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 1
Position ULD Remaining Weight Average H-Arm Moment to add
11 10.700 m(421.26 in)
12 12.272 m(483.15 in)
21 13.844 m(545.04 in)
22 15.416 m(606.93 in)
23 16.988 m(668.82 in)
Containers and Pallets in FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 2
B. Aft Lower Cargo CompartmentThe forward cargo compartment is designed for the transport of bulk cargo and baggage or thefollowing unit load devices:- 5 x half size containers LD3-46 (NAS 3610-2K2C, IATA contour AKG)- 5 x full size containers LD3-46W (NAS 3610-2K2C, IATA contour AKH)- 5 x 60.4x61.5 in pallets LD3-46P (NAS 3610-2K3P)See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
3147.2 to 47.5
27.419 m(1079.49 in)
3247.5 to 50
29.096 m(1145.51 in)
3350 to 52A/53
30.696 m(1208.50 in)
4152A/53 to 56
32.296 m(1271.50 in)
03-50-01Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Section Frame Station RemainingWeight
Average H-ArmMoment to add
4256 to 59
33.896 m(1334.49 in)
Total47.2 to 59
30.619 m(1205.47 in)
Bulk Cargo in Aft FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 3
Position ULD Remaining Weight Average H-Arm Moment to add
31 27.445 m(1080.51 in)
32 29.017 m(1142.40 in)
33 30.589 m(1204.29 in)
41 32.161 m(1266.18 in)
42 33.733 m(1328.07 in)
Containers and Pallets in Aft Cargo Compartment Remaining Weight and Related H-arm
TABLE 4
C. Bulk Cargo CompartmentThe aft cargo compartment is designed for the transport of bulk cargo and baggage.See your WBM to determine applicable Y-arm.
Section Frame Station RemainingWeight
Average H-ArmMoment to add
5159 to 60
34.963 m(1376.50 in)
5260 to 62
35.764 m(1408.03 in)
5362 to 65
37.123 m(1461.54 in)
03-50-01Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Section Frame Station RemainingWeight
Average H-ArmMoment to add
Total59 to 65
36.322 m(1430.00 in)
Bulk Cargo in Aft FWD Cargo Compartment Remaining Weight and Related H-arm
TABLE 5
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets09-10-14 09-10-14-CARGO COMPARTMENTS
Referenced Information
TABLE 6
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : IF CARGO AND BAGGAGE ARE NOT - OR CANNOT BE - REMOVED, MAKESURE THAT THEY ARE SAFELY FASTENED AND THAT LOADS ARE ASSYMMETRICAL AS POSSIBLE BEFORE YOU START THE RECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
03-50-01Page 22
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 03-50-01-558-020-A01
A. How to Find the Effect of Cargo and Baggage Remaining on the Deck
(1) Use the tables in Job Setup References to determine H-arm moments and Y-arm momentsby reporting the masses of each container or pallet.
(2) Record the calculated values on FWD Cargo Compartment (in Zone 130) , Aft CargoCompartment (in Zone 150) , Bulk Cargo Compartment (in Zone 160) into boxes of theCargo and Baggage Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 23
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
FWDCARGODOOR
11 12
1.430 m(56.30 in)
2.630 m(103.54 in)
1.21
3 m
(47.
76 in
)0.
051
m(2
.00
in)
21 22 23
A
A
ULD
CONTAINERWIDEBODYCOMPATIBLE
NAS3610 2K2CLD3−45IATA CODE AKG
PALLETWIDEBODYCOMPATIBLE
PALLETNSA3610 2K2P
CONTAINERFULL WIDTH
NAS3610 2K2CLD3−45IATA CODE AKH
N_AR_035001_1_0070101_01_00
FR24 FR35.5
FWD Cargo Compartment ArrangementPallets and Containers
FIGURE-03-50-01-991-007-A01
03-50-01Page 24
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
FWDCARGODOOR
31 32
1.430 m(56.30 in)
2.630 m(103.54 in)
1.21
3 m
(47.
76 in
)0.
051
m(2
.00
in)
33 41 42
A
ULD
CONTAINERWIDEBODYCOMPATIBLE
NAS3610 2K2CLD3−45IATA CODE AKG
PALLETWIDEBODYCOMPATIBLE
PALLETNSA3610 2K2P
CONTAINERFULL WIDTH
NAS3610 2K2CLD3−45IATA CODE AKH
A
N_AR_035001_1_0080101_01_00
FR47.1 FR59
Aft Cargo Compartment ArrangementPallets and Containers
FIGURE-03-50-01-991-008-A01
03-50-01Page 25
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-802-A01
Total Traffic Load Remaining Effect
1. GeneralThere are overhead stowage compartments for hand baggage and coats along the full length of thepassenger compartments, above the passenger seats.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 1
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-002-A01
A. How to Find the Effect of Traffic Load Remaining
(1) Use data from the Weight and Balance Manual and/or from your specific aircraftconfiguration data to find the weight, H-arm values and related moment of traffic loadremaining.
(2) Calculate H-arm moments generated by the traffic load and record it on the Traffic LoadRemaining Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 26
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-803-A01
Ballast Added Effect
1. GeneralBallast is any heavy material that you use to add weight if you want to stabilize the aircraft with theCG change method.Ballast can be non recovery kit stock items (such as sand bags, drums filled with water, livestock feedsacks, etc.) that you can buy in-situ. It is important that the ballast is easily transportable to the site,easily managed by the personnel on site and that, if there is a shift in the aircraft CG, no secondarydamage will occur if the ballast moves inside the aircraft or when it is necessary to transport theaircraft.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets09-10-06 09-10-06-FUSELAGE FRAMES AND H-ARM TABLE09-10-08 09-10-08-WING RIBS AND STATIONS
Referenced Information
TABLE 1
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
03-50-01Page 27
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 03-50-01-558-003-A01
A. How to find the Effect of Added Ballast
(1) To find the effect of added ballast, you need to find the H-arm and, if applicable, the Y-arm of the zone in which you added ballast.To calculate the necessary average H-arm and Y-arm:- See 09-10-06 for ballast added inside of fuselage,- See 09-10-08 for ballast added on the wing,
(2) Calculate the H-arm and Y-arm moments generated by the weight of ballast you use andrecord them on the Ballast Added Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 28
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-804-A01
Waste Water Remaining Effect
1. GeneralThe aircraft is equipped with a vacuum system.The waste water from the lavatories and galleys is stored in 1 waste tank (See DESC 09-10-12-006-A01 for tank capacity and pre-charged chemical fluid quantities).The waste tank is installed in the pressurized underfloor area in the aft fuselage.
2. InspectionsNot Applicable.
3. Job Setup References
Item Remaining Weight H-arm Moment to add
Tank N˚1 - A318 25.928 m (1020.79 in)
Tank N˚1 - A319 28.316 m (1114.80 in)
Tank N˚1 - A320 32.050 m (1261.81 in)
Tank N˚1 - A321 38.984 m (1534.80 in)
Waste Water Remaining Weight and Relevant H-arm
TABLE 1
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-10-12-006-A01 DESC 09-10-12-006-A01-Waste Water Disposal System
DESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 2
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
03-50-01Page 29
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-004-A01
A. How to Find the Effect of Waste Water Remaining
(1) To find the effect of waste water remaining, you must know the weight of the waste waterremaining into tanks minus the pre-load. The generated H-arm moments must becalculated with the data given in the table in Job Setup References .
NOTE : The assumptions are that:- After a flight, 2/3 of the potable water is in the waste tank and the volume
of water remaining in the potable water tank is negligible,- At take off, the potable water tank are full.
(2) Calculate the H-arm moments generated by the waste water and report them on the WasteWater Remaining Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 30
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-805-A01
Non OEW Catering Equipment Added Effect
1. GeneralIf your Weight and CG calculation is based on OEW, you need to include the NON-OEW CateringEquipment effect.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 1
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-005-A01
A. How to Find the Effect of NON-OEW Catering Equipment Added
(1) Use data from the Weight and Balance Manual and/or from your specific aircraftconfiguration data to find the weight and H-arm values and related moments of NON-OEW catering equipment, which was removed.
(2) Calculate H-arm moments generated by the NON-OEW Catering Equipment and recordthem on the NON-OEW Catering Equipment Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 31
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-806-A01
Potable Water Removed Effect
1. GeneralThe aircraft is equipped with a pressurized potable water system.Potable water for the toilets and galleys is stored in 1 tank, which is installed in the pressurizedunderfloor area.See DESC 09-10-12-005-A01 for potable water tanks capacities.
NOTE : The number of items of equipment can change with the customer.
2. InspectionsNot Applicable.
3. Job Setup ReferencesThe table that follow gives the average H-arm, from standard aircraft configuration.
Item Remaining Weight Average H-arm Moment to subtract
Tank N˚ 1 - A318 25.663 m (1010.35 in)
Tank N˚1 - A319 28.051 m (1104.37 in)
Tank N˚1 - A320 31.785 m (1251.38 in)
Tank N˚1 - A321 38.719 m (1524.37 in)
Average H-arm
TABLE 1
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-10-12-005-A01 DESC 09-10-12-005-A01-Potable Water System
DESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 2
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
03-50-01Page 32
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-006-A01
A. How to Find the Effect of Potable Water Removed
(1) Weight and CG calculation is based on OEW or DOW, which include full potable watertank.
(2) To find the effect of removed potable water, you must know the weight of the potablewater which was moved to the waste tank during flight or manually removed on recoverysite. The generate H-arm moments have to be calculated with data provided in the table inJob Setup References .
NOTE : The assumptions are that:- After a flight, 2/3 of the potable water is in the waste tank and the volume
of water remaining in the potable water tank is negligible,- At take off, the potable water tank are full.
(3) Calculate H-arm moments generated by the Potable Water Removed and record it on thePotable Water Removed Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 33
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-807-A01
Cockpit and Cabin Crew Removed Effect
1. GeneralWeight and CG calculation is based on OEW or DOW, which include cockpit and cabin crew.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 1
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-007-A01
A. How to Find the Effect of Removed Cockpit and Cabin Crew
(1) Use data from Weight and Balance Manual and/or from your specific aircraft configurationdata to find weight, H-arm value and related moment of cockpit and cabin crew included inthe OEW or in the DOW, which were removed.
(2) Calculate H-arm moments generated by the cockpit and cabin crew removed and report iton the Cockpit and Cabin Crew Removed interim worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 34
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-808-A01
Catering Equipment Removed Effect
1. GeneralWeight and CG calculation is based on OEW or DOW, which include catering equipment.
NOTE : For Non-OEW Catering Equipment Effect, see TASK 03-50-01-558-805-A01.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 03-50-01-558-805-A01 TASK 03-50-01-558-805-A01-Non OEW Catering Equipment
Added EffectDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 1
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-008-A01
A. How to find the Effect of Catering Equipment Removed
(1) Use data from the Weight and Balance Manual and/or from your specific aircraftconfiguration data to find the weight, H-arm and Y-arm and related moments of cateringequipment which was removed from OEW or DOW configuration.
03-50-01Page 35
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(2) Calculate H-arm and Y-arm moments generated by the Catering Equipment Removed andreport it on the Catering Equipment Removed Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 36
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 03-50-01-558-809-A01
Hydraulic Fluid Removed Effect
1. GeneralThe aircraft has 3 hydraulic circuits. See DESC 09-10-12-002-A01 for hydraulic circuit details.
2. InspectionsNot Applicable.
3. Job Setup ReferencesThe tables that follow give the average H-arm from standard aircraft configuration, with HydraulicFluid removed. Use these values with the total weight of Hydraulic Fluid.The Weights are based on an Hydraulic Fluid density of 1.002 kg per liter.
Hydraulic System - A318
Item Capacity Remaining Weight H-arm Moment tosubtract
Green Tank 14 l (3.70 US gal) 16.594 m (653.31in)
Yellow Tank 12 l (3.17 US gal) 15.944 m (627.72in)
Blue Tank 6 l (1.59 US gal) 20.294 m (798.98in)
Systems 147 l (38.83 USgal)
16.708 m (657.80in)
A/C Total 202 l (53.36 USgal)
16.769 m (660.20in)
Hydraulic Fluid Tank Remaining Weight and Relevant H-arm - A318
TABLE 1
Hydraulic System - A319
Item Capacity Remaining Weight H-arm Moment tosubtract
Green Tank 14 l (3.70 US gal) 17.382 m (684.33in)
Yellow Tank 12 l (3.17 US gal) 16.732 m (658.74in)
Blue Tank 6 l (1.59 US gal) 21.082 m (830.00in)
03-50-01Page 37
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Hydraulic System - A319
Item Capacity Remaining Weight H-arm Moment tosubtract
Systems 148 l (39.10 USgal)
18.462 m (726.85in)
A/C Total 180 l (47.55 USgal)
18.350 m (722.44in)
Hydraulic Fluid Tank Remaining Weight and Relevant H-arm - A319
TABLE 2
Hydraulic System - A320
Item Capacity Remaining Weight H-arm Moment tosubtract
Green Tank 14 l (3.70 US gal) 18.982 m (747.32in)
Yellow Tank 12 l (3.17 US gal) 18.332 m (721.73in)
Blue Tank 6 l (1.59 US gal) 22.682 m (892.99in)
Systems 152 l (40.15 USgal)
20.168 m (794.02in)
A/C Total 184 l (48.61 USgal)
20.040 m (788.98in)
Hydraulic Fluid Tank Remaining Weight and Relevant H-arm - A320
TABLE 3
Hydraulic System - A321
Item Capacity Remaining Weight H-arm Moment tosubtract
Green Tank 14 l (3.70 US gal) 23.249 m (915.31in)
Yellow Tank 12 l (3.17 US gal) 22.599 m (889.72in)
Blue Tank 6 l (1.59 US gal) 26.949 m (1060.98in)
Systems 170 l (44.91 USgal)
24.150 m (950.79in)
03-50-01Page 38
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Hydraulic System - A321
Item Capacity Remaining Weight H-arm Moment tosubtract
A/C Total 202 l (53.36 USgal)
24.079 m (947.99in)
Hydraulic Fluid Tank Remaining Weight and Relevant H-arm - A321
TABLE 4
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-10-12-002-A01 DESC 09-10-12-002-A01-Hydraulic System
DESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 5
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-009-A01
A. How to Find the Effect of Hydraulic Fluid Removed
(1) Weight and CG calculation is based on OEW or DOW which include hydraulic fluid.
(2) Use the table in Job Setup References to calculate H-arm moment to subtract.
(3) Calculate H-arm moments generated by the hydraulic fluids removed and record them onthe Hydraulic Fluids Removed Interim Worksheet. (See DESC 09-50-01-001-A01).
03-50-01Page 39
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
TASK 03-50-01-558-810-A01
Large Components Removed / Missing
1. GeneralThe equipment or aircraft parts that follow may have a significant effect on weight and balancemanagement for the recovery.- APU and tail cone- APU- Pax doors- Cargo doors- Radome- Pylon- Thrust reversers- Bare engines- Complete power plant- Rudders- VTP equipped- HTP equipped- Elevators- Slats- Flaps- Ailerons- Spoilers- Winglet / wingtip- Landing gear equipped- Landing gear Leg Fairing- Wheels- BrakesIf you need to remove some of these large components during recovery or if some of these largecomponents are missing when you start the recovery process, use the data that follow and calculationtables to determine the effect on NRW and the CG position.
2. InspectionsNot Applicable.
3. Job Setup References
A. Wing Equipment Table
Item Weight H-Arm H-Arm Moment
Slat 1 43 kg(95 lb)
14.092 m(554.80 in)
605.956 kgm(52706 lb.in)
03-50-01Page 40
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Slat 2 30 kg(66 lb)
16.064 m(632.44 in)
481.920 kgm(41741.04 lb.in)
Slat 3 28 kg(62 lb)
17.412 m(685.51 in)
487.536 kgm(42501.62 lb.in)
Slat 4 25 kg(55 lb)
18.698 m(736.14 in)
467.45 kgm(40487.7 lb.in)
Slat 5 24 kg(53 lb)
19.912 m(783.94 in)
477.888 kgm(41548.82 lb.in)
Inner Flap 107 kg(236 lb)
18.331 m(721.69 in)
1961.417 kgm(170318.84 lb.in)
Outer Flap 120 kg(265 lb)
19.466 m(766.38 in)
2335.92 kgm(203090.7 lb.in)
Spoiler 1 16 kg(35 lb)
18.159 m(714.92 in)
290.544 kgm(25022.2 lb.in)
Spoiler 2 14 kg(31 lb)
18.528 m(729.45 in)
259.392 kgm(22612.95 lb.in)
Spoiler 3 13 kg(29 lb)
19.099 m(751.93 in)
248.287 kgm(21805.97 lb.in)
Spoiler 4 12 kg(26 lb)
19.671 m(774.45 in)
236.052 kgm(22459.05 lb.in)
Spoiler 5 14 kg(31 lb)
20.258 m(797.56 in)
283.612 kgm(24724.36 lb.in)
Aileron 24 kg(53 lb)
21.231 m(835.87 in)
509.544 kgm(44301.11 lb.in)
Wing Tip and Winglet 26 kg(57 lb)
21.504 m(846.61 in)
559.104 kgm(48256.77 lb.in)
Equipment on Wing
TABLE 1
B. Fuselage Equipment Table
Item Weight H-Arm H-Arm Moment
Forward Passenger/Crew Door 98 kg(216 lb)
7.579 m(298.39 in)
742.742 kgm(64452.24 lb.in)
Aft Passenger/Crew Door 96 kg(212 lb)
25.960 m(1022.05 in)
2492.16 kgm(216674.6 lb.in)
Emergency Exit 13 kg(29 lb)
15.430 m(607.48 in)
200.59 kgm(17616.92 lb.in)
03-50-01Page 41
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Forward Cargo Door 91 kg(201 lb)
10.433 m(410.75 in)
949.403 kgm(82560.75 lb.in)
Aft Cargo Door 103 kg(227 lb)
21.507 m(846.73 in)
2215.221 kgm(192207.71 lb.in)
Radome 26 kg(57 lb)
3.300 m(129.92 in)
85.8 kgm(7405.44 lb.in)
APU and Tailcone 470 kg(1036 lb)
31.862 m(1254.41 in)
14975.14 kgm(1299568.76 lb.in)
APU 139 kg(306 lb)
32.032 m(1261.10 in)
4452.448 kgm(385896.6 lb.in)
Fuselage Equipment
TABLE 2
C. Vertical Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 270 kg(595 lb)
30.519 m(1201.54 in)
8240.13 kgm(714916.3 lb.in)
Rudder 95 kg(209 lb)
31.621 m(1244.92 in)
3003.995 kgm(260188.28 lb.in)
Removable Leading Edge 75 kg(165 lb)
29.296 m(1153.39 in)
2197.2 kgm(190309.35 lb.in)
Tip 20 kg(44 lb)
32.549 m(1281.46 in)
650.98 kgm(56384.24 lb.in)
Fuselage Fairing 11 kg(24 lb)
29.832 m(1174.49 in)
328.152 kgm(28187.76 lb.in)
VTP Equipment
TABLE 3
D. Horizontal Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 417 kg(919 lb)
30.413 m(1197.36 in)
12682.221 kgm(1100373.84 lb.in)
Elevator 96 kg(212 lb)
31.909 m(1256.26 in)
3063.264 kgm(266327.12 lb.in)
Removable Leading Edge 84 kg(185 lb)
30.219 m(1189.72 in)
2538.396 kgm(220098.2 lb.in)
03-50-01Page 42
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Tip 6 kg(13 lb)
32.355 m(1273.82 in)
194.13 kgm(16559.66 lb.in)
Tailplane Fuselage Fairing 7 kg(15 lb)
31.135 m(1225.79 in)
217.945 kgm(18386.85 lb.in)
HTP Equipment
TABLE 4
E. Power Plant Equipment Table
Item Weight H-Arm H-Arm Moment
Inlet Cowl 138 kg(304 lb)
11.960 m(470.87 in)
1650.48 kgm(143144.48 lb.in)
Fan Cowl LH 37 kg(82 lb)
12.820 m(504.72 in)
474.34 kgm(41387.04 lb.in)
Fan Cowl RH 42 m(1654 in)
12.820 m(504.72 in)
538.44 kgm(834806.88 lb.in)
Thrust Reverser LH 193 kg(425 lb)
13.943 m(548.94 in)
2691 kgm(233299.5 lb.in)
Thrust Reverser RH 212 kg(467 lb)
13.943 m(548.94 in)
2955.916 kgm(256354.98 lb.in)
Bare Engine 2778 kg(6124 lb)
13.541 m(533.11 in)
3766.898 kgm(3264765.64 lb.in)
Complete Power Plant 3501 kg(7718 lb)
13.565 m(534 in)
47491.065 kgm(4121412 lb.in)
Pylon 593 kg(1307 lb)
15.118 m(595.20 in)
8964.974 kgm(777926.4 lb.in)
Power Plant Equipment - CFM 56 Engine
TABLE 5
Item Weight H-Arm H-Arm Moment
Inlet Cowl 127 kg(280 lb)
11.921 m(469.33 in)
1513.967 kgm(131412.4 lb.in)
Fan Cowl 90 kg(198 lb)
12.803 m(504.06 in)
1152.27 kgm(99803.88 lb.in)
Thrust Reverser 579 kg(1276 lb)
13.290 m(523.23 in)
7694.91 kgm(667641.48 lb.in)
03-50-01Page 43
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Bare Engine 2644 kg(5829 lb)
13.640 m(537.01 in)
36064.16 kgm(3130231.229 lb.in)
Complete Power Plant 3567 kg(7864 lb)
13.673 m(538.31 in)
48771.591 kgm(4233269.84 lb.in)
Pylon 576 kg(1270 lb)
15.227 m(599.49 in)
8770.752 kgm(761352.3 lb.in)
Power Plant Equipment - PW 6000 Engine
TABLE 6
F. Landing Gear Equipment Table
Item Weight H-Arm H-Arm Moment
Nose Landing Gear Complete 327 kg(721 lb)
7.600 m(299.21 in)
2485.2 kgm(215730.41 lb.in)
Wheel with Tire 35 kg(77 lb)
7.605 m(299.41 in)
266.175 kgm(23054.57 lb.in)
NLG Equipment
TABLE 7
Item Weight H-Arm H-Arm Moment
MLG Leg Fairing 16 kg(35 lb)
17.225 m(678.15 in)
275.6 kgm(23735.25 lb.in)
Main Landing Gear Complete 1010 kg(2227 lb)
17.670 m(695.67 in)
17846.7 kgm(1549257.09 lb.in)
Wheel with Tire 135 kg(298 lb)
17.862 m(703.23 in)
2411.37 kgm(209562.54 lb.in)
Brake 69 kg(152 lb)
17.862 m(703.23 in)
1232.478 kgm(106890.96 lb.in)
MLG Equipment
TABLE 8
03-50-01Page 44
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 9
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-010-A01
A. How to find the Effect of Large Components Removed / Missing
(1) See the tables in Job Setup References to determine the weight, H-arm, Y-arm and Z-armMoment.
(2) Record Weight, H-arm, Y-arm and Z-arm moment into the relevant boxes of the LargeComponent Removed / Missing Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 45
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
TASK 03-50-01-558-810-B01
Large Components Removed / Missing
1. GeneralThe equipment or aircraft parts that follow may have a significant effect on weight and balancemanagement for the recovery.- APU and tail cone- APU- Pax doors- Cargo doors- Radome- Pylon- Thrust reversers- Bare engines- Complete power plant- Rudders- VTP equipped- HTP equipped- Elevators- Slats- Flaps- Ailerons- Spoilers- Winglet / wingtip- Landing gear equipped- Landing gear Leg Fairing- Wheels- BrakesIf you need to remove some of these large components during recovery or if some of these largecomponents are missing when you start the recovery process, use the data that follow and calculationtables to determine the effect on NRW and the CG position.
2. InspectionsNot Applicable.
3. Job Setup References
A. Wing Equipment Table
Item Weight H-Arm H-Arm Moment
Slat 1 43 kg(95 lb)
14.092 m(554.80 in)
605.956 kgm(52706 lb.in)
03-50-01Page 46
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Slat 2 30 kg(66 lb)
16.064 m(632.44 in)
481.92 kgm(41741.04 lb.in)
Slat 3 28 kg(62 lb)
17.412 m(685.51 in)
487.536 kgm(42501.62 lb.in)
Slat 4 25 kg(55 lb)
18.698 m(736.14 in)
467.45 kgm(40487.7 lb.in)
Slat 5 24 kg(53 lb)
19.912 m(783.94 in)
477.888 kgm(41548.82 lb.in)
Inner Flap 107 kg(236 lb)
18.331 m(721.69 in)
1961.41 kgm(170318.84 lb.in)
Outer Flap 120 kg(265 lb)
19.466 m(766.38 in)
2335.92 kgm(203090.7 lb.in)
Spoiler 1 16 kg(35 lb)
18.159 m(714.92 in)
290.544 kgm(25022.2 lb.in)
Spoiler 2 14 kg(31 lb)
18.528 m(729.45 in)
259.392 kgm(22612.95 lb.in)
Spoiler 3 13 kg(29 lb)
19.099 m(751.93 in)
248.287 kgm(21805.97 lb.in)
Spoiler 4 12 kg(26 lb)
19.671 m(774.45 in)
236.052 kgm(20135.7 lb.in)
Spoiler 5 14 kg(31 lb)
20.258 m(797.56 in)
283.612 kgm(24724.36 lb.in)
Aileron 24 kg(53 lb)
21.231 m(835.87 in)
509.544 kgm(44301.11 lb.in)
Wing Tip and Winglet 26 kg(57 lb)
21.504 m(846.61 in)
559.104 kgm(48256.77 lb.in)
Equipment on Wing
TABLE 1
B. Fuselage Equipment Table
Item Weight H-Arm H-Arm Moment
Forward Passenger/Crew Door 98 kg(216 lb)
7.579 m(298.39 in)
742.742 kgm(64452.24 lb.in)
Aft Passenger/Crew Door 96 kg(212 lb)
28.351 m(1116.18 in)
2721.696 kgm(236630.16 lb.in)
Emergency Exit (Optional) 15 kg(33 lb)
15.371 m(605.16 in)
230.57 kgm(19970.28 lb.in)
03-50-01Page 47
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Emergency Exit 15 kg(33 lb)
16.217 m(638.46 in)
243.255 kgm(31069.18 lb.in)
Forward Cargo Door 112 kg(247 lb)
13.240 m(521.26 in)
1482.88 kgm(128751.22 lb.in)
Aft Cargo Door 112 kg(247 lb)
25.635 m(1009.25 in)
2871.12 kgm(249284.75 lb.in)
Radome 26 kg(57 lb)
3.300 m(129.92 in)
85.8 kgm(7405.44 lb.in)
APU and Tailcone 460 kg(1014 lb)
34.241 m(1348 in)
15750.86 kgm(1366872 lb.in)
APU 137 kg(302 lb)
34.420 m(1355.12 in)
4715.54 kgm(409246.24 lb.in)
Fuselage Equipment
TABLE 2
C. Vertical Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 270 kg(595 lb)
32.117 m(1264.45 in)
8671.59 kgm(752347.75 lb.in)
Rudder 91 kg(201 lb)
33.963 m(1337.13 in)
3090.633 kgm(268763.13 lb.in)
Removable Leading Edge 77 kg(170 lb)
30.894 m(1216.30 in)
2378.838 kgm(206771 lb.in)
Tip 10 kg(22 lb)
34.176 m(1345.51 in)
341.76 kgm(29601.22 lb.in)
Fuselage Fairing 15 kg(33 lb)
31.440 m(1237.80 in)
471.6 kgm(40847.4 lb.in)
VTP Equipment
TABLE 3
D. Horizontal Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 417 kg(919 lb)
32.800 m(1291.34 in)
13677.6 kgm(1186741.46 lb.in)
Elevator 96 kg(212 lb)
34.296 m(1350.24 in)
3292.416 kgm(286250.88 lb.in)
03-50-01Page 48
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Removable Leading Edge 84 kg(185 lb)
32.606 m(1283.70 in)
2738.904 kgm(237484.5 lb.in)
Tip 6 kg(13 lb)
34.742 m(1367.80 in)
208.452 kgm(17781.4 lb.in)
Tailplane Fuselage Fairing 7 kg(15 lb)
33.522 m(1319.76 in)
234.654 kgm(19796.4 lb.in)
HTP Equipment
TABLE 4
E. Power Plant Equipment Table
Item Weight H-Arm H-Arm Moment
Inlet Cowl 138 kg(304 lb)
12.748 m(501.89 in)
1759.224 kgm(152574.56 lb.in)
Fan Cowl LH 37 kg(82 lb)
13.608 m(535.75 in)
503.496 kgm(43931.5 lb.in)
Fan Cowl RH 42 m(1654 in)
13.608 m(535.75 in)
571.536 kgm(886130.5 lb.in)
Thrust Reverser LH 193 kg(425 lb)
14.731 m(579.96 in)
2843.083 kgm(246440.5 lb.in)
Thrust Reverser RH 212 kg(467 lb)
14.731 m(579.96 in)
3122.972 kgm(270841.32 lb.in)
Bare Engine 2778 kg(6124 lb)
14.329 m(564.13 in)
39805.962 kgm(3454732.12 lb.in)
Complete Power Plant 3501 kg(7718 lb)
14.353 m(565.08 in)
50249.853 kgm(4361287.44 lb.in)
Pylon 593 kg(1307 lb)
15.906 m(626.22 in)
9432.258 kgm(818469.54 lb.in)
Power Plant Equipment - CFM 56 Engine
TABLE 5
Item Weight H-Arm H-Arm Moment
Inlet Cowl 121 kg(267 lb)
12.479 m(491.30 in)
1509.959 kgm(131177.1 lb.in)
Fan Cowl 98 kg(216 lb)
13.577 m(534.53 in)
1330.546 kgm(115458.48 lb.in)
03-50-01Page 49
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Thrust Reverser 518 kg(1142 lb)
15.005 m(590.75 in)
7772.59 kgm(674636.5 lb.in)
Bare Engine 2665 kg(5875 lb)
14.366 m(565.59 in)
38285.39 kgm(3322841.25 lb.in)
Complete Power Plant 3520 kg(7760 lb)
14.454 m(569.06 in)
50878.08 kgm(4415905.6 lb.in)
Pylon 597 kg(1316 lb)
15.860 m(624.41 in)
9468.42 kgm(821723.56 lb.in)
Power Plant Equipment - IAE V2500 Engine
TABLE 6
F. Landing Gear Equipment Table
Item Weight H-Arm H-Arm Moment
Nose Landing Gear Complete 327 kg(721 lb)
7.600 m(299.21 in)
2485.2 kgm(215730.41 lb.in)
Wheel with Tire 35 kg(77 lb)
7.605 m(299.41 in)
266.175 kgm(23054.57 lb.in)
NLG Equipment
TABLE 7
Item Weight H-Arm H-Arm Moment
MLG Leg Fairing 16 kg(35 lb)
18.013 m(709.17 in)
288.208 kgm(24820.95 lb.in)
Main Landing Gear Complete 1010 kg(2227 lb)
18.458 m(726.69 in)
18642.58 kgm(1618338.63 lb.in)
Wheel with Tire 135 kg(298 lb)
18.650 m(734.25 in)
2517.75 kgm(218806.5 lb.in)
Brake 69 kg(152 lb)
18.650 m(734.25 in)
1286.85 kgm(111606 lb.in)
MLG Equipment
TABLE 8
03-50-01Page 50
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 9
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-012-A01
A. How to find the Effect of Large Components Removed / Missing
(1) See the tables in Job Setup References to determine the weight, H-arm, Y-arm and Z-armMoment.
(2) Record Weight, H-arm, Y-arm and Z-arm moment into the relevant boxes of the LargeComponent Removed / Missing Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 51
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
TASK 03-50-01-558-810-C01
Large Components Removed / Missing
1. GeneralThe equipment or aircraft parts that follow may have a significant effect on weight and balancemanagement for the recovery.- APU and tail cone- APU- Pax doors- Cargo doors- Radome- Pylon- Thrust reversers- Bare engines- Complete power plant- Rudders- VTP equipped- HTP equipped- Elevators- Slats- Flaps- Ailerons- Spoilers- Winglet / wingtip- Landing gear equipped- Landing gear Leg Fairing- Wheels- BrakesIf you need to remove some of these large components during recovery or if some of these largecomponents are missing when you start the recovery process, use the data that follow and calculationtables to determine the effect on NRW and the CG position.
2. InspectionsNot Applicable.
3. Job Setup References
A. Wing Equipment Table
Item Weight H-Arm H-Arm Moment
Slat 1 39 kg(86 lb)
16.470 m(648.43 in)
642.33 kgm(55764.98 lb.in)
03-50-01Page 52
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Slat 2 30 kg(66 lb)
18.460 m(726.77 in)
553.8 kgm(47966.82 lb.in)
Slat 3 28 kg(62 lb)
19.790 m(779 in)
554.12 kgm(48298 lb.in)
Slat 4 25 kg(55 lb)
21.070 m(829.53 in)
526.75 kgm(45624.15 lb.in)
Slat 5 23 kg(51 lb)
22.290 m(877.56 in)
512.67 kgm(44755.56 lb.in)
Inner Flap 114 kg(251 lb)
20.716 m(815.59 in)
2361.624 kgm(204713.09 lb.in)
Outer Flap 122 kg(269 lb)
21.872 m(861.10 in)
2668.384 kgm(231635.9 lb.in)
Spoiler 1 15 kg(33 lb)
20.394 m(802.91 in)
305.91 kgm(26496.03 lb.in)
Spoiler 2 13 kg(29 lb)
20.824 m(819.84 in)
270.712 kgm(23775.36 lb.in)
Spoiler 3 12 kg(26 lb)
21.424 m(843.46 in)
257.088 kgm(21929.96 lb.in)
Spoiler 4 12 kg(26 lb)
21.984 m(865.51 in)
263.808 kgm(22503.26 lb.in)
Spoiler 5 14 kg(31 lb)
22.519 m(886.57 in)
315.266 kgm(27483.67 lb.in)
Aileron 24 kg(53 lb)
23.582 m(928.43 in)
565.968 kgm(49206.79 lb.in)
Wing Tip (A320-100) 15 kg(33 lb)
23.680 m(932.28 in)
355.2 kgm(30765.24 lb.in)
Wing Tip and Winglet(A320-200)
26 kg(57 lb)
23.960 m(943.31 in)
622.96 kgm(53768.67 lb.in)
Equipment on Wing
TABLE 1
B. Fuselage Equipment Table
Item Weight H-Arm H-Arm Moment
Forward Passenger/Crew Door 98 kg(216 lb)
7.579 m(298.39 in)
742.742 kgm(64452.24 lb.in)
Aft Passenger/Crew Door 96 kg(212 lb)
32.085 m(1263.19 in)
3080.16 kgm(267796.28 lb.in)
03-50-01Page 53
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Emergency Exit 15 kg(33 lb)
16.971 m(668.15 in)
267.27 kgm(2248.95 lb.in)
Emergency Exit 15 kg(33 lb)
17.818 m(701.50 in)
267.27 kgm(23149.5 lb.in)
Forward Cargo Door 121 kg(267 lb)
10.700 m(421.26 in)
1294.7 kgm(265203.09 lb.in)
Aft Cargo Door 121 kg(267 lb)
25.229 m(993.27 in)
3052.709 kgm(265203.09 lb.in)
Bulk Cargo Door 37 kg(82 lb)
28.859 m(1136.18 in)
1067.783 kgm(93166.76 lb.in)
Radome 26 kg(57 lb)
3.300 m(129.92 in)
85.8 kgm(7405.44 lb.in)
APU and Tailcone 460 kg(1014 lb)
37.985 m(1495.47 in)
17473.1 kgm(1516406.58 lb.in)
APU 136 kg(300 lb)
38.155 m(1502.17 in)
5189.08 kgm(450651 lb.in)
Fuselage Equipment
TABLE 2
C. Vertical Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 365 kg(805 lb)
36.003 m(1417.44 in)
13141.095 kgm(1141039.2 lb.in)
Rudder 88 kg(194 lb)
37.702 m(1484.33 in)
3317.776 kgm(287960.02 lb.in)
Removable Leading Edge 48 kg(106 lb)
35.332 m(1391.02 in)
1695.936 kgm(147448.12 lb.in)
Tip 9 kg(20 lb)
37.910 m(1492.52 in)
341.19 kgm(39850.4 lb.in)
Dorsal Fin 26 kg(57 lb)
33.067 m(1301.85 in)
859.742 kgm(74205.45 lb.in)
Fuselage Fairing 15 kg(33 lb)
35.174 m(1384.80 in)
527.61 kgm(45698.4 lb.in)
VTP Equipment
TABLE 3
03-50-01Page 54
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
D. Horizontal Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 418 kg(922 lb)
36.534 m(1438.35 in)
15271.212 kgm(1326158.7 lb.in)
Elevator 97 kg(214 lb)
38.030 m(1497.24 in)
3688.91 kgm(320409.36 lb.in)
Removable Leading Edge 84 kg(185 lb)
36.340 m(1430.71 in)
3052.56 kgm(264681.35 lb.in)
Tip 6 kg(13 lb)
38.476 m(1514.80 in)
230.856 kgm(19692.4 lb.in)
Tailplane Fuselage Fairing 7 kg(15 lb)
37.256 m(1466.77 in)
260.792 kgm(22001.55 lb.in)
HTP Equipment
TABLE 4
E. Power Plant Equipment Table
Item Weight H-Arm H-Arm Moment
Inlet Cowl 138 kg(304 lb)
14.453 m(569.02 in)
1994.514 kgm(172982.08 lb.in)
Fan Cowl LH 37 kg(82 lb)
15.296 m(602.20 in)
565.952 kgm(49380.4 lb.in)
Fan Cowl RH 42 m(1654 in)
15.296 m(602.20 in)
642.432 kgm(996038.8 lb.in)
Thrust Reverser LH 193 kg(425 lb)
16.369 m(644.45 in)
3159.217 kgm(273891.25 lb.in)
Thrust Reverser RH 212 kg(467 lb)
16.369 m(644.45 in)
3470.228 kgm(300958.15 lb.in)
Bare Engine 2778 kg(6124 lb)
15.963 m(628.46 in)
44345.214 kgm(3848689.04 lb.in)
Complete Power Plant 3501 kg(7718 lb)
15.987 m(629.41 in)
55970.487 kgm(4857786.38 lb.in)
Pylon 593 kg(1307 lb)
15.987 m(629.41 in)
9480.291 kgm(822638.87 lb.in)
Power Plant Equipment - CFM 56 Engine
TABLE 5
03-50-01Page 55
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Inlet Cowl 121 kg(267 lb)
14.110 m(555.51 in)
1707.31 kgm(148321.17 lb.in)
Fan Cowl 98 kg(216 lb)
15.120 m(595.28 in)
1481.76 kgm(128580.48 lb.in)
Thrust Reverser 518 kg(1142 lb)
16.524 m(650.55 in)
8559.432 kgm(742928.1 lb.in)
Bare Engine 2665 kg(5875 lb)
15.975 m(628.94 in)
42573.375 kgm(3695022.5 lb.in)
Complete Power Plant 3520 kg(7760 lb)
16.063 m(632.40 in)
56541.76 kgm(4907424 lb.in)
Pylon 597 kg(1316 lb)
17.514 m(689.53 in)
10455.858 kgm(907421.48 lb.in)
Power Plant Equipment - IAE V2500 Engine
TABLE 6
F. Landing Gear Equipment Table
Item Weight H-Arm H-Arm Moment
Nose Landing Gear Complete 323 kg(712 lb)
7.617 m(299.88 in)
2460.291 kgm(213514.56 lb.in)
Wheel with Tire 36 kg(79 lb)
7.628 m(300.31 in)
274.608 kgm(23724.49 lb.in)
NLG Equipment
TABLE 7
Item Weight H-Arm H-Arm Moment
MLG Leg Fairing 16 kg(35 lb)
19.675 m(774.61 in)
314.8 kgm(27111.35 lb.in)
Main Landing Gear Complete(Twin Wheel MLG)
931 kg(2053 lb)
20.067 m(790.04 in)
18682.377 kgm(1621952.12 lb.in)
Wheel with Tire and Brake(Twin Wheel MLG)
204 kg(450 lb)
20.250 m(797.24 in)
4131 kgm(358758 lb.in)
Main Landing Gear Complete(Optional Four Wheel BogieMLG)
1234 kg(2721 lb)
20.056 m(789.61 in)
24749.104 kgm(2148528.81 lb.in)
03-50-01Page 56
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Wheel with Tire and Brake(Optional Four Wheel BogieMLG)
114 kg(251 lb)
20.266 m(797.87 in)
2310.324 kgm(200265.37 lb.in)
MLG Equipment
TABLE 8
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 9
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
03-50-01Page 57
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 03-50-01-558-013-A01
A. How to find the Effect of Large Components Removed / Missing
(1) See the tables in Job Setup References to determine the weight, H-arm, Y-arm and Z-armMoment.
(2) Record Weight, H-arm, Y-arm and Z-arm moment into the relevant boxes of the LargeComponent Removed / Missing Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 58
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
TASK 03-50-01-558-810-D01
Large Components Removed / Missing
1. GeneralThe equipment or aircraft parts that follow may have a significant effect on weight and balancemanagement for the recovery.- APU and tail cone- APU- Pax doors- Cargo doors- Radome- Pylon- Thrust reversers- Bare engines- Complete power plant- Rudders- VTP equipped- HTP equipped- Elevators- Slats- Flaps- Ailerons- Spoilers- Winglet / wingtip- Landing gear equipped- Landing gear Leg Fairing- Wheels- BrakesIf you need to remove some of these large components during recovery or if some of these largecomponents are missing when you start the recovery process, use the data that follow and calculationtables to determine the effect on NRW and the CG position.
2. InspectionsNot Applicable.
3. Job Setup References
A. Wing Equipment Table
Item Weight H-Arm H-Arm Moment
Slat 1 43 kg(95 lb)
20.747 m(816.81 in)
892.121 kgm(77596.95 lb.in)
03-50-01Page 59
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Slat 2 31 kg(68 lb)
22.719 m(894.45 in)
704.289 kgm(60822.6 lb.in)
Slat 3 28 kg(62 lb)
24.067 m(947.52 in)
673.876 kgm(58746.24 lb.in)
Slat 4 27 kg(60 lb)
25.353 m(998.15 in)
684.531 kgm(59889 lb.in)
Slat 5 25 kg(55 lb)
26.567 m(1045.94 in)
664.175 kgm(57526.7 lb.in)
Inner Flap 124 kg(273 lb)
25.195 m(991.93 in)
3124.18 kgm(270796.89 lb.in)
Inner Flap Tab 85 kg(187 lb)
25.195 m(991.93 in)
2141.575 kgm(185490.91 lb.in)
Outer Flap 120 kg(265 lb)
26.143 m(1029.25 in)
3137.16 kgm(272751.25 lb.in)
Outer Flap Tab 80 kg(176 lb)
26.139 m(1029.09 in)
2091.12 kgm(181119.84 lb.in)
Spoiler 1 16 kg(35 lb)
24.754 m(974.57 in)
396.064 kgm(34109.95 lb.in)
Spoiler 2 14 kg(31 lb)
25.205 m(992.32 in)
352.87 kgm(30761.92 lb.in)
Spoiler 3 13 kg(29 lb)
25.754 m(1013.94 in)
334.802 kgm(39404.26 lb.in)
Spoiler 4 12 kg(26 lb)
26.267 m(1034.13 in)
315.204 kgm(26887.38 lb.in)
Spoiler 5 14 kg(31 lb)
26.913 m(1059.57 in)
376.782 kgm(32846.67 lb.in)
Aileron 24 kg(53 lb)
27.854 m(1096.61 in)
668.496 kgm(58120.33 lb.in)
Wing Tip and Winglet 26 kg(57 lb)
28.165 m(1108.86 in)
732.29 kgm(63205.02 lb.in)
Equipment on Wing
TABLE 1
B. Fuselage Equipment Table
Item Weight H-Arm H-Arm Moment
Forward Passenger/Crew Door 98 kg(216 lb)
7.579 m(298.39 in)
742.742 kgm(64452.24 lb.in)
03-50-01Page 60
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Aft Passenger/Crew Door 96 kg(212 lb)
39.016 m(1536.06 in)
3745.536 kgm(325644.72 lb.in)
Emergency Exit FWD RH 70 kg(154 lb)
16.384 m(645.04 in)
1146.88 kgm(99336.16 lb.in)
Emergency Exit FWD LH 81 kg(179 lb)
16.384 m(645.04 in)
1327.104 kgm(115462.16 lb.in)
Emergency Exit Aft 70 kg(154 lb)
27.331 m(1076.02 in)
1913.17 kgm(165707.08 lb.in)
Forward Cargo Door 112 kg(247 lb)
10.681 m(420.51 in)
1196.272 kgm(103865.97 lb.in)
Aft Cargo Door 112 kg(247 lb)
32.139 m(1265.32 in)
3599.568 kgm(312534.04 lb.in)
Bulk Cargo Door 34 kg(75 lb)
35.793 m(1409.17 in)
1216.962 kgm(105687.75 lb.in)
Radome 26 kg(57 lb)
3.300 m(129.92 in)
85.8 kgm(7405.44 lb.in)
APU and Tailcone 460 kg(1014 lb)
44.923 m(1768.62 in)
20664.58 kgm(1793380.68 lb.in)
APU 145 kg(320 lb)
45.089 m(1775.16 in)
6537.905 kgm(598051.2 lb.in)
Fuselage Equipment
TABLE 2
C. Vertical Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 270 kg(595 lb)
42.797 m(1684.92 in)
11555.19 kgm(1002527.4 lb.in)
Rudder 91 kg(201 lb)
44.631 m(1757.13 in)
4061.421 kgm(353183.13 lb.in)
Removable Leading Edge 77 kg(170 lb)
41.562 m(1636.30 in)
3200.274 kgm(278171 lb.in)
Tip 10 kg(22 lb)
44.844 m(1765.51 in)
448.44 kgm(38841.22 lb.in)
03-50-01Page 61
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Fuselage Fairing 15 kg(33 lb)
42.108 m(1657.80 in)
631.62 kgm(54707.4 lb.in)
VTP Equipment
TABLE 3
D. Horizontal Stabilizer Equipment Table
Item Weight H-Arm H-Arm Moment
Box 417 kg(919 lb)
43.468 m(1711.34 in)
18126.156 kgm(1572721.46 lb.in)
Elevator 96 kg(212 lb)
44.964 m(1770.24 in)
4316.544 kgm(375.290.88 lb.in)
Removable Leading Edge 84 kg(185 lb)
43.274 m(1703.70 in)
359.016 kgm(315184.5 lb.in)
Tip 6 kg(13 lb)
45.410 m(1787.80 in)
272.46 kgm(23241.4 lb.in)
Tailplane Fuselage Fairing 7 kg(15 lb)
44.190 kg(97.42 lb)
309.33 kgm(1461.3 lb.in)
HTP Equipment
TABLE 4
E. Power Plant Equipment Table
Item Weight H-Arm H-Arm Moment
Inlet Cowl 138 kg(304 lb)
18.615 m(732.87 in)
2568.87 kgm(222792.48 lb.in)
Fan Cowl LH 37 kg(82 lb)
19.475 m(766.73 in)
720.575 kgm(62871.86 lb.in)
Fan Cowl RH 42 m(1654 in)
19.475 m(766.73 in)
817.95 kgm(1268171.42 lb.in)
Thrust Reverser LH 193 kg(425 lb)
20.598 m(810.94 in)
3975.414 kgm(344649.5 lb.in)
Thrust Reverser RH 212 kg(467 lb)
20.598 m(810.94 in)
4366.776 kgm(378708.98 lb.in)
Bare Engine 2778 kg(6124 lb)
20.196 m(795.12 in)
56104.488 kgm(4869314.88 lb.in)
Complete Power Plant 3501 kg(7718 lb)
20.220 m(796.06 in)
70790.22 kgm(6143991.08 lb.in)
03-50-01Page 62
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Pylon 593 kg(1307 lb)
21.773 m(857.20 in)
12911.389 kgm(1120360.4 lb.in)
Power Plant Equipment - CFM 56 Engine
TABLE 5
Item Weight H-Arm H-Arm Moment
Inlet Cowl 121 kg(267 lb)
18.346 m(722.28 in)
2219.866 kgm(192848.76 lb.in)
Fan Cowl 98 kg(216 lb)
19.444 m(765.51 in)
1905.512 kgm(165350.16 lb.in)
Thrust Reverser 518 kg(1142 lb)
20.872 m(821.73 in)
10811.696 kgm(938415.66 lb.in)
Bare Engine 2665 kg(5875 lb)
20.233 m(796.57 in)
53920.945 kgm(4679848.75 lb.in)
Complete Power Plant 3520 kg(7760 lb)
20.321 m(800.04 in)
71529.92 kgm(6208310.4 lb.in)
Pylon 597 kg(1316 lb)
21.727 m(855.39 in)
12971.019 kgm(1125693.24 lb.in)
Power Plant Equipment - IAE V2500 Engine
TABLE 6
F. Landing Gear Equipment Table
Item Weight H-Arm H-Arm Moment
Nose Landing Gear Complete 327 kg(720.91 lb)
7.600 m(299.21 in)
2485.2 kgm(215703.4811 lb.in)
Wheel with Tire 35 kg(77 lb)
7.605 m(299.41 in)
266.175 kgm(23054.57 lb.in)
NLG Equipment
TABLE 7
Item Weight H-Arm H-Arm Moment
MLG Leg Fairing 23 kg(51 lb)
23.960 m(943.31 in)
551.08 kgm(48108.81 lb.in)
Main Landing Gear Complete 1176 kg(2593 lb)
24.339 m(958.23 in)
28622.664 kgm(2484690.29 lb.in)
03-50-01Page 63
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Item Weight H-Arm H-Arm Moment
Wheel with Tire 166 kg(366 lb)
24.517 m(965.24 in)
4069.822 kgm(353277.84 lb.in)
Brake 93 kg(205 lb)
24.517 m(965.24 in)
2280.081 kgm(197874.2 lb.in)
MLG Equipment
TABLE 8
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 9
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
03-50-01Page 64
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 03-50-01-558-014-A01
A. How to find the Effect of Large Components Removed / Missing
(1) See the tables in Job Setup References to determine the weight, H-arm, Y-arm and Z-armMoment.
(2) Record Weight, H-arm, Y-arm and Z-arm moment into the relevant boxes of the LargeComponent Removed / Missing Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 65
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100
TASK 03-50-01-558-811-A01
Large Components Movement Effect
1. GeneralThe CG positions of the OEW or the DOW apply to specific aircraft conditions which include thelanding gear extended and the flaps and slats retracted.
NOTE : The thrust reverser extension effect is negligible on the A/C CG.
2. InspectionsNot Applicable.
3. Job Setup References
A. Landing Gear Retraction
Landing Gear Retraction H-arm Moment to Subtract
NLG 204 kgm (17706 lb.in)
MLG 801 kgm (69523 lb.in)
L/G Retraction Effect
TABLE 1
B. Droop Nose, Slats and Flaps Extension Effect
H-arm MomentsCockpit IndicationSlats / Flaps Slats Flaps Total
0 0.0 0.0 0.0
AUTOMATIC- 96.5 kgm(- 8376 lb.in) 0.0
- 96.5 kgm(- 8376 lb.in)
1- 96.5 kgm(- 8376 lb.in)
220.0 kgm(19095 lb.in)
123.5 kgm(10719 lb.in)
2- 106.0 kgm(- 9200 lb.in)
275.5 kgm(23912 lb.in)
169.5 kgm(14712 lb.in)
3- 106.0 kgm(- 9200 lb.in)
330.5 kgm(28686 lb.in)
224.5 kgm(19486 lb.in)
FULL- 118.1 kgm(- 10251 lb.in)
358.1 kgm(31082 lb.in)
240.0 kgm(20831 lb.in)
Slats and Flaps Extension Effect
TABLE 2
NOTE : Add or subtract H-arm moments in accordance with the positive or negatives values.
03-50-01Page 66
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 3
5. Procedure
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLSURFACES AND THE LANDING GEARS AND RELATED DOORS ARE CLEAR.MOVEMENT OF THE CONTROL SURFACES AND LANDING GEARS/DOORS CANCAUSE INJURY TO PERSONS AND/OR DAMAGE TO THE AIRCRAFT OREQUIPMENT.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-011-A01
A. How to Find the Effect of Large Component Movement
(1) To find the effect of large component movement, you must know the moments (generatedby H-arm and Y-arm) depending of Aircraft Landing Gear retraction and Slats and Flapsextension.
(2) To know this, see Job Setup References and record the H-arm and Y-arm moment on theLarge Component Movement Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 67
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
TASK 03-50-01-558-811-B01
Large Components Movement Effect
1. GeneralThe CG positions of the OEW or the DOW apply to specific aircraft conditions which include thelanding gear extended and the flaps and slats retracted.
NOTE : The thrust reverser extension effect is negligible on the A/C CG.
2. InspectionsNot Applicable.
3. Job Setup References
A. Landing Gear Retraction
Landing Gear Retraction H-arm Moment to Subtract
NLG 202 kgm (17533 lb.in)
MLG 738 kgm (64055 lb.in)
L/G Retraction Effect - Twin Wheel MLG
TABLE 1
Landing Gear Retraction H-arm Moment to Subtract
NLG 208 kgm (18054 lb.in)
MLG 776 kgm (67354 lb.in)
L/G Retraction Effect - Optional Four Wheel Bogie MLG
TABLE 2
B. Droop Nose, Slats and Flaps Extension Effect
H-arm MomentsCockpit IndicationSlats / Flaps Slats Flaps
Total
0 0.0 0.0 0.0
AUTOMATIC- 96.5 kgm(- 8376 lb.in) 0.0
- 96.5 kgm(- 8376 lb.in)
1- 96.5 kgm(- 8376 lb.in)
220.0 kgm(19095 lb.in)
123.5 kgm(10719 lb.in)
2- 96.5 kgm(- 8376 lb.in)
275.5 kgm(23912 lb.in)
179.0 kgm(15536 lb.in)
3- 96.5 kgm(- 8376 lb.in)
330.5 kgm(28686 lb.in)
234.0 kgm(20310 lb.in)
03-50-01Page 68
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
H-arm MomentsCockpit IndicationSlats / Flaps Slats Flaps
Total
FULL- 118.1 kgm(- 10251 lb.in)
358.1 kgm(31081 lb.in)
240.0 kgm(20831 lb.in)
Slats and Flaps Extension Effect
TABLE 3
NOTE : Add or subtract H-arm moments in accordance with positive or negative values.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 4
5. Procedure
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLSURFACES AND THE LANDING GEARS AND RELATED DOORS ARE CLEAR.MOVEMENT OF THE CONTROL SURFACES AND LANDING GEARS/DOORS CANCAUSE INJURY TO PERSONS AND/OR DAMAGE TO THE AIRCRAFT OREQUIPMENT.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
03-50-01Page 69
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 03-50-01-558-015-A01
A. How to Find the Effect of Large Component Movement
(1) To find the effect of large component movement, you must know the moments (generatedby H-arm and Y-arm) depending of Aircraft Landing Gear retraction and Slats and Flapsextension.
(2) To know this, see Job Setup References and record the H-arm and Y-arm moment on theLarge Component Movement Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 70
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
TASK 03-50-01-558-811-C01
Large Components Movement Effect
1. GeneralThe CG positions of the OEW or the DOW apply to specific aircraft conditions which include thelanding gear extended and the flaps and slats retracted.
NOTE : The thrust reverser extension effect is negligible on the A/C CG.
2. InspectionsNot Applicable.
3. Job Setup References
A. Landing Gear Retraction
Landing Gear Retraction H-arm Moment to Subtract
NLG 207 kgm (17967 lb.in)
MLG 1017 kgm (88271 lb.in)
L/G Retraction Effect
TABLE 1
B. Droop Nose, Slats and Flaps Extension Effect
H-arm MomentsCockpit IndicationSlats / Flaps Slats Flaps Total
0 0.0 0.0 0.0
AUTOMATIC-101.8 kgm(- 8836 lb.in) 0.0
-101.8 kgm(- 8836 lb.in)
1-101.8 kgm(- 8836 lb.in)
285.0 kgm(24737 lb.in)
183.2 kgm(15901 lb.in)
2- 111.9 kgm(- 9712 lb.in)
328.4 kgm(28504 lb.in)
216.5 kgm(18791 lb.in)
3- 111.9 kgm(- 9712 lb.in)
377.0 kgm(32722 lb.in)
265.1 kgm(23009 lb.in)
FULL-124.6 kgm(-10815 lb.in)
395.7 kgm(34345 lb.in)
271.1 kgm(23530 lb.in)
Slats and Flaps Extension Effect
TABLE 2
NOTE : Add or subtract H-arm moments in accordance with positive or negative values.
03-50-01Page 71
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONDESC 09-50-01-001-A01 DESC 09-50-01-001-A01-Worksheets
Referenced Information
TABLE 3
5. Procedure
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLSURFACES AND THE LANDING GEARS AND RELATED DOORS ARE CLEAR.MOVEMENT OF THE CONTROL SURFACES AND LANDING GEARS/DOORS CANCAUSE INJURY TO PERSONS AND/OR DAMAGE TO THE AIRCRAFT OREQUIPMENT.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
NOTE : It is important to use accurate data for the calculation related to the recovery process.Some of the necessary data is the responsibility of the operator and to be accurate, it mustbe applicable to the specific MSN involved. Data supplied by the manufacturer as genericdata is not necessarily accurate for a specific MSN. Refer to the operator’s documentationfor precise calculations.If some of the necessary data is not available or if it is not possible to get it, then it is theresponsibility of the recovery manager to decide to use estimated data and to continue withthe process.
Subtask 03-50-01-558-016-A01
A. How to Find the Effect of Large Component Movement
(1) To find the effect of large component movement, you must know the moments (generatedby H-arm and Y-arm) depending of Aircraft Landing Gear retraction and Slats and Flapsextension.
(2) To know this, see Job Setup References and record the H-arm and Y-arm moment on theLarge Component Movement Effect Interim Worksheet (See DESC 09-50-01-001-A01).
03-50-01Page 72
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
03-60-01 REFERENCE FOR CALCULATION
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 03-60-01-001-A01
Information Required and Source Data
1. General
CAUTION : THE NRW AND CG LOCATION CAN ONLY BE AS ACCURATE AS THE DATAUSED TO CALCULATE THEM. IF ACCURATE DATA IS NOT AVAILABLE OR IFTHE DATA USED ARE EXTRAPOLATIONS, THIS WILL HAVE AN EFFECT ONTHE RESULTS THAT YOU GET.
This section gives the details on definitions related to CG management, and the source of therequired data. It also tells you how to use these data to calculate the NRW and CG location.In most cases, several sources exist to find the required data.Accurate calculations require specific data based on the specific aircraft MSN and actual airline loadand trim sheet information.In case of a serious aircraft accident and subsequent freeze of the aircraft documentation, genericaircraft type data can be used. This can also apply if it is impossible to power the onboardcomputers.
NOTE : Contact telephone numbers for the load and weight and balance office should be readilyavailable.
**ON A/C A318-100
2. OEW (Operating Empty Weight) or DOW (Dry Operating Weight) and associated H-arm:
CAUTION : IF YOU USE THE OEW GENERIC DATA TO CALCULATE THE NRW, THE CGPOSITION AND THE EXPECTED LOADS, THE RESULTS YOU GET WILL NOTBE ACCURATE.
It is possible to take the data from these sources:- Airline Load and Trim Sheet,- Onboard Computers,- Weight and Balance Manual,- The generic OEW with an associated CG at 25 %RC is about 38818 kg (85579 lb) with CFM
engines or 38661 kg (85233 lb) with PW Engines.
NOTE : The OEW or DOW and the associated H-arm are given for a specific aircraft configuration:all landing gear extended flight control retracted and thrust reversers in stored position.
03-60-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
3. OEW (Operating Empty Weight) or DOW (Dry Operating Weight) and associated H-arm:
CAUTION : IF YOU USE THE OEW GENERIC DATA TO CALCULATE THE NRW, THE CGPOSITION AND THE EXPECTED LOADS, THE RESULTS YOU GET WILL NOTBE ACCURATE.
It is possible to take the data from these sources:- Airline Load and Trim Sheet,- Onboard Computers,- Weight and Balance Manual,- The generic OEW with an associated CG at 25 %RC is about 39725 kg (87579 lb) with CFM
engines or 39826 kg (87801 lb) with IAE engines.
NOTE : The OEW or DOW and the associated H-arm are given for a specific aircraft configuration:all landing gear extended flight control retracted and thrust reversers in stored position.
**ON A/C A320-100
4. OEW (Operating Empty Weight) or DOW (Dry Operating Weight) and associated H-arm:
CAUTION : IF YOU USE THE OEW GENERIC DATA TO CALCULATE THE NRW, THE CGPOSITION AND THE EXPECTED LOADS, THE RESULTS YOU GET WILL NOTBE ACCURATE.
It is possible to take the data from these sources:- Airline Load and Trim Sheet,- Onboard Computers,- Weight and Balance Manual,- The generic OEW with an associated CG at 25 %RC. is about 41244 kg (90927 lb) with CFM
engines.
NOTE : The OEW or DOW and the associated H-arm are given for a specific aircraft configuration:all landing gear extended flight control retracted and thrust reversers in stored position.
**ON A/C A320-200
5. OEW (Operating Empty Weight) or DOW (Dry Operating Weight) and associated H-arm:
CAUTION : IF YOU USE THE OEW GENERIC DATA TO CALCULATE THE NRW, THE CGPOSITION AND THE EXPECTED LOADS, THE RESULTS YOU GET WILL NOTBE ACCURATE.
It is possible to take the data from these sources:- Airline Load and Trim Sheet,- Onboard Computers,- Weight and Balance Manual,- The generic OEW with an associated CG at 25 %RC is about 41244 kg (90927 lb) with CFM
engines or 41345 kg (91150 lb) with IAE engines.
03-60-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
NOTE : The OEW or DOW and the associated H-arm are given for a specific aircraft configuration:all landing gear extended flight control retracted and thrust reversers in stored position.
**ON A/C A321-100 A321-200
6. OEW (Operating Empty Weight) or DOW (Dry Operating Weight) and associated H-arm:
CAUTION : IF YOU USE THE OEW GENERIC DATA TO CALCULATE THE NRW, THE CGPOSITION AND THE EXPECTED LOADS, THE RESULTS YOU GET WILL NOTBE ACCURATE.
It is possible to take the data from these sources:- Airline Load and Trim Sheet,- Onboard Computers,- Weight and Balance Manual,- The generic OEW with an associated CG at 25 %RC is about 46858 kg (103304 lb) with CFM
engines or 46959 kg (103527 lb) with IAE engines.
NOTE : The OEW or DOW and the associated H-arm are given for a specific aircraft configuration:all landing gear extended flight control retracted and thrust reversers in stored position.
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
7. Source Data
A. Flight Crew- Weight and H-arm are specific to the operator,- Use generic data from the Weight and Balance Manual.
B. Cabin Crew- Weight and H-arm are specific to the operator,- Use generic data from the Weight and Balance Manual.
C. Remaining fuel
(1) The means of extracting data that can be used:- Use data from the total fuel weight from load and trim sheet,- Use data from MCDU,- Do the measurements from dip sticks or do an estimation based on fuel load of 1/4,
1/2, 3/4 (See 03-20-02 and 03-20-01),- Do an estimation of the remaining fuel weight from the trim load sheet based on the
operator’s known fuel consumption.
(2) Find the associated H-arm and Y-arm. Theses values depend on the distribution of the fuelload. See 03-20-02 to assess the fuel quantity (dip stick, MCDU, or specific method), andassociated H-arm and Y-arm.
D. PayloadThis could be split in passengers and cargo:
03-60-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(1) Passenger PayloadIn most cases, the passengers will have removed carry on luggage, unless an emergencyevacuation took place in which case it is necessary to take the weight of the carry onluggage into account.- Take the total passenger weight from the load and trim sheet,- H-arm: The operator should provide the H-arm relevant to its cabin sections.- H-arm should be calculated from 03-50-01.
(2) Cargo Payload- Use the total cargo payload weight from the load and trim sheet,- H-arm : the operator should give the H-arm associated to cargo compartments,- H-arm : extract generic data from the Weight and Balance Manual,- Calculate H-arm see 03-50-01- Do approximate weight and position estimations based on observation,- Ask for assistance of airline load office.
E. Weight and H-arm of any Missing or Removed Large Components- Take the weight of the removed units,- Use weights and moments listed in chapter 03-50-01,- Use details from the Weight and Balance Manual.
F. Weight of the operator’s equipment- Use data from the Weight and Balance Manual.- H-arm calculated in chapter 03-50-01,
G. Weight of Fluids either Removed or On Board- Use data from the Weight and Balance Manual.- H-arm calculated in 03-50-01,
H. Weight and Location of Catering Equipment and Water Remaining On Board.Weight and H-arm depend on the aircraft configuration, the operator’s route being flown andthe season of operation:- Use generic data from the Weight and Balance Manual.
J. Change of the moment with landing gear retracted or leading edge and trailing edge surfacesextended.- See 03-50-01
03-60-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
PREPARATION
04-00-00 PREPARATION
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 04-00-00-001-A01
General
1. TetheringIt is generally agreed that the aircraft must be tethered during recovery leveling and lifting operations.However, it is necessary to evaluate carefully the benefit and purpose.
A. During leveling or lifting, make sure that the aircraft is stable, and prevent uncontrolledmovement of the aircraft.This movement can be caused by:- Change of CG position during aircraft lifting/leveling- Weather conditions- Terrain conditions change: humidity, temperature, soil capability.
B. These conditions will help you decide whether to tether the aircraft or not:- Aircraft attitude- Leveling/lifting procedure used- Terrain conditions- Wind/weather condition- Increase of aircraft stability foreseen.It is necessary to do an evaluation of the tethering loads. They must be in the aircraft allowablelimits. During the tethering operation, it is necessary to continuously monitor these loads.
2. ShoringShoring of the aircraft can also be necessary to make it stable prior to remove fuel or cargo payloador to allow a change/repositioning of the recovery tooling.For the shoring operation, it is possible to use large timbers to support or stabilize the forward or aftfuselage and/or the lower wing surfaces. These supports must be placed in the correct load bearingareas and be adequately padded to prevent damage.For example, it is possible to make fuselage supports or cradles to match the contours of the fuselageframes. Adequate padding can consist of heavy felt, rubber sheets, rubber tires, mattresses or sandbags.The same conditions as above will help you decide whether to shore the aircraft or not.The shoring loads must be evaluated, be in the aircraft allowable limits and monitored. All appliedloads for allowable skin pressure and fuselage bending moment calculations must also be in the ARMlimits.
3. Lifting and Tethering MaterialSee 09-30-01.
04-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
04-20-00 STABILIZING THE AIRCRAFT
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 04-20-00-588-801-A01
Stabilizing the Aircraft
1. GeneralThe operations that follow are necessary to stabilize the aircraft.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-200-801-A01 TASK 02-30-01-200-801-A01-Landing Gear Survey
03-50-01 03-50-01-MANAGING AIRCRAFT WEIGHT AND CG04-30-00 04-30-00-TETHERING THE AIRCRAFT05-30-00 05-30-00-MOVING FUEL FOR CG CONTROLFIGURE 04-20-00-991-001-A FIGURE 04-20-00-991-001-A-Aircraft Stability
FIGURE 04-20-00-991-001-B FIGURE 04-20-00-991-001-B-Aircraft Stability
FIGURE 04-20-00-991-001-C FIGURE 04-20-00-991-001-C-Aircraft Stability
FIGURE 04-20-00-991-001-D FIGURE 04-20-00-991-001-D-Aircraft Stability
Referenced Information
TABLE 1
5. Procedure
Subtask 04-20-00-588-001-A01
A. General
(1) Make sure that maximum weight has been removed to make the aircraft as light aspossible.
(2) Calculate the NRW and CG position (see 03-50-01).
(3) You must also make sure that the wind speed is not more than the maximum allowablespeed. See FIGURE 04-20-00-991-001-AFIGURE 04-20-00-991-001-BFIGURE04-20-00-991-001-CFIGURE 04-20-00-991-001-D.
04-20-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(4) Monitor visually the ground contact point of the A/C (either L/G or jack) to detect anymovement or attitude change during the leveling and lifting operation. If load cells areavailable on recovery jacks, monitor load indication shift.The monitoring of the vertical position of the shock absorber in the strut with a referenceline can be also an indicator of A/C stability.
(5) Select the method that you will use to control the CG during the leveling/lifting operationby addition or removal of ballast and transfer of fuel.
(6) Make sure the aircraft is correctly grounded.
(7) Install landing gear downlock pins in all landing gears that are extended (see TASK02-30-01-200-801-A01).
(8) Install tethers as soon as possible if the aircraft is unstable and moves in the wind (see04-30-00).
(9) Install temporary shoring timbers in relation with the tethers to help stabilize the aircraftwhen necessary.
(10) Transfer fuel from the low wing to the opposite wing to move weight and leveling/liftingload from the low wing (see 05-30-00).It is also possible to use this procedure to reduce the loads on an engine resting on theground.
(11) The shock absorber of the low wing landing gear can be inflated while the shock absorberof the landing gear on the high wing can be deflated to help raise a low wing.
(12) It is possible to operate the spoilers in strong wind conditions to help stabilize the aircraft(see TBD).
(13) Put the horizontal stabilizer to a slightly nose down position.
NOTE : You can do this only if power is available on the aircraft.
(14) Stabilize the soil around the aircraft so that cargo loading equipment and fuel tankers cancome near to the aircraft.
(15) Make sure that the aircraft CG position stays at least 500 mm (20 in) forward the aircraftbalance point (which is the aircraft support point: the main landing gear or the wing mainjacks).
NOTE : Other operations may be necessary depending on the specific recovery conditions.
(16) To determine the aircraft stability refer to FIGURE 04-20-00-991-001-AFIGURE04-20-00-991-001-BFIGURE 04-20-00-991-001-CFIGURE 04-20-00-991-001-D.
04-20-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
NR
W IN
TO
NS
CG % RC10 15 20 25 30 40 45 5035
35
30
40
45
50
55
60
65
130 km/h (70 Kt)
111 km/h (60 Kt)
120 km/h (65 Kt)
102 km/h (55 Kt)
93 km/h (50 Kt)
83 km
(45
Kt)
74 km
(40
Kt)
46 km
(25
Kt)
0 km
(0 K
t)
9 km
(5 K
t)
65 km
(35
Kt)
56 km
(30
Kt)
37 km
(20
Kt)
28 km
(15
Kt) 19 km
(10
Kt)
N_AR_042000_1_0010101_01_00
Aircraft StabilityWheels on Dry Ground (Sheet 1 of 3)
FIGURE-04-20-00-991-001-A01
04-20-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
NR
W IN
TO
NS
CG % RC
111 km/h (60 Kt)
102 km/h (55 Kt)
83 km/h (45 Kt)
74 km/h (40 Kt)
1510 25 30 35 40 45 502030
35
40
45
50
55
65
60
93 km/h (50 Kt)
46 km
(25
Kt)
0 km
(0 K
t)
9 km
(5 K
t)
65 km
(35
Kt)
56 km
(30
Kt)
37 km
(20
Kt)
28 km
(15
Kt)
19 km
(10
Kt)
N_AR_042000_1_0010102_01_00
Aircraft StabilityWheels on Wet Ground (Sheet 2 of 3)
FIGURE-04-20-00-991-001-A01
04-20-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
NR
W IN
TO
NS
30
35
40
45
50
55
60
65
CG (% RC)
AIRCRAFT CG (% RC)
10 15 20 25 30 35 40 45 5015
Kt (
28 k
m/h
)
10 K
t (19
km
/h)
SHIFTING
0 Kt
(0 k
m/h
)
5 Kt
(9 k
m/h
)
N_AR_042000_1_0010103_01_00
Aircraft StabilityWheels on Ice Ground (Sheet 3 of 3)
FIGURE-04-20-00-991-001-A01
04-20-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
35
40
45
50
55
60
65
70
75
80
1416182022 262830 3436 40 4244464812108 50
NR
W IN
TO
NS
CG %RC24 32 38
148 km/h (80 Kt)
139 km/h (75 Kt)
130 km/h (70 Kt)
120 km/h (65 Kt)
102 km/h (55 Kt)
SHIFTING
TIPPIN
G
0 km
/h (0
Kt)
93 km
/h (5
0 Kt)
83 km
/h (4
5 Kt)
65 km
/h (3
5 Kt)
56 km
/h (3
0 Kt)
46 km
/h (2
5 Kt)
37 km
/h (2
0 Kt)74
km/h
(40
Kt)28
km/h
(15
Kt)
19 km
/h (1
0 Kt)
9 km
/h (5
Kt)
WIND SPEED
111 km/h (60 Kt)
N_AR_042000_1_0010201_01_00
Aircraft StabilityWheels on Dry Ground (Sheet 1 of 3)
FIGURE-04-20-00-991-001-B01
04-20-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
35
40
45
50
55
60
65
70
75
80
141618202224262830323412108
NR
W IN
TO
NS
363840 4244464850 CG % RC
65 km
/h (3
5 Kt)
56 km
/h (3
0 Kt)
46 km
/h (2
5 Kt)
37 k
m/h
(20
Kt)
28 km
/h (1
5 Kt) 19
km/h
(10
Kt)
0 km
/h (0
Kt)
SHIFTING
120 km/h (65 Kt)
111 km/h (60 Kt)
102 km/h (55 Kt)
TIPPIN
G
74 k
m/h
(40
Kt)
WIND SPEED
9 km
/h (5
Kt)
93 km/h (50 Kt)
83 km/h (45 Kt)
N_AR_042000_1_0010202_01_00
Aircraft StabilityWheels on Wet Ground (Sheet 2 of 3)
FIGURE-04-20-00-991-001-B01
04-20-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
NR
W IN
TO
NS
5010 20 30 4015 25 35 4535
40
45
50
55
60
65
70
75
80
AIRCRAFT CG (% RC)
AIRCRAFT CG (% RC)20 Kt (37 km/h)
SHIFTING
15 K
t (28
km
/h)
10 K
t (19
km
/h)
0 Kt
(0 k
m/h
)
5 K
t (9
km/h
)
N_AR_042000_1_0010203_01_00
Aircraft StabilityWheels on Ice Ground (Sheet 3 of 3)
FIGURE-04-20-00-991-001-B01
04-20-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
35
40
45
50
55
60
65
70
75
80
14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 4812108 50
NR
W IN
TO
NS
CG (% RC)
SHIFTING
111 km/h (60 Kt)
102 km/h (55 Kt)
93 km/h (50 Kt)
TIPPIN
G
83 km
/h (4
5 Kt)
65 km
/h (3
5 Kt)
37 km
/h (2
0 Kt)74
km/h
(40
Kt)
83 km/h (45 Kt)
56 km
/h (3
0 Kt)
N_AR_042000_1_0010301_01_00
120 km/h (65 Kt)
130 km/h (70 Kt)
46 km
/h (2
5 Kt)
WIND SPEED
Aircraft StabilityWheels on Dry Ground (Sheet 1 of 3)
FIGURE-04-20-00-991-001-C01
04-20-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
35
40
45
50
55
60
65
70
75
80
14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 4812108 50
NR
W IN
TO
NS
CG (% RC)
SHIFTING
111 km/h (60 Kt)
102 km/h (55 Kt)
93 km/h (50 Kt)
TIPPIN
G
83 km/h (45 Kt)
74 km/h (40 Kt) 65 km/h (35 Kt)
N_AR_042000_1_0010302_01_00
65 km
/h (3
5 Kt)
56 km
/h (3
0 Kt)
37 km
/h (2
0 Kt)
46 km
/h (2
5 Kt)
WIND SPEED
Aircraft StabilityWheels on Wet Ground (Sheet 2 of 3)
FIGURE-04-20-00-991-001-C01
04-20-00Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
NR
W IN
TO
NS
5010 20 30 4015 25 35 45 CG (% RC)35
40
45
50
55
60
65
70
75
80
5 Kt
(9 k
m/h
)
10 Kt (19 km/h)
15 Kt (28 km/h)
SHIFTING
N_AR_042000_1_0010303_01_00
Aircraft StabilityWheels on Ice Ground (Sheet 3 of 3)
FIGURE-04-20-00-991-001-C01
04-20-00Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
35
40
45
50
55
60
65
70
75
80
14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 4812108 50 CG % RC
NR
W IN
TO
NS
TIPPIN
G
SHIFTING
111 km/h (60 Kt)
56 km
/h (3
0 Kt)
37 k
m/h
(20
Kt)74 k
m/h
(40
Kt)
83 k
m/h
(45
Kt)
102 km/h (55 Kt)
74 km/h (40 Kt)46
km/h
(25
Kt)
65 km
/h (3
5 Kt)
93 km/h (50 Kt)
120 km/h (65 Kt)
WIND SPEED
N_AR_042000_1_0010401_01_00
Aircraft StabilityWheels on Dry Ground (Sheet 1 of 3)
FIGURE-04-20-00-991-001-D01
04-20-00Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
35
40
45
50
55
60
65
70
75
80
14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 4812108 50
NR
W IN
TO
NS
CG % RC
SHIFTING
56 km/h (30 Kt)
56 k
m/h
(30
Kt)
46 km
/h (2
5 Kt)
37 k
m/h
(20
Kt)
WIND SPEED
TIPPIN
G
102 km/h (55 Kt)
93 km/h (50 Kt)
83 km/h (45 Kt)
74 km/h (40 Kt)
65 km/h (35 Kt)
N_AR_042000_1_0010402_01_00
Aircraft StabilityWheels on Wet Ground (Sheet 2 of 3)
FIGURE-04-20-00-991-001-D01
04-20-00Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
NR
W IN
TO
NS
5010 20 30 4015 25 35 45 CG (% RC)
AIRCRAFT CG (% RC)
35
40
45
50
55
60
65
70
75
80
5 Kt
(9 k
m/h
)0
Kt (0
km
/h)
15 Kt (28 km/h)
SHIFTING
10 Kt (19 km/h)
N_AR_042000_1_0010403_01_00
Aircraft StabilityWheels on Ice Ground (Sheet 3 of 3)
FIGURE-04-20-00-991-001-D01
04-20-00Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
04-30-00 TETHERING THE AIRCRAFT
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 04-30-00-001-A01
General
1. Tethering the aircraft
CAUTION : YOU MUST NOT USE THE SAME FITTING TO TETHER THE AIRCRAFT ANDTO LIFT IT AT THE SAME TIME.IF YOU USE THE SAME FITTING, THERE IS ARISK THAT THE LOADS APPLIED WILL BE MORE THAN THE ALLOWABLELOADS. THIS CAN CAUSE DAMAGE TO THE STRUCTURE.
CAUTION : YOU MUST INSTALL TENSIONING DEVICES AND A SCALE OR ADYNAMOMETER ON EACH TETHERING LINE. USE THE TENSIONING DEVICESTO ADJUST THE LENGTH OF THE LINE AND KEEP A POSITIVE LOAD.DURING THE LEVELING AND LIFTING PROCESS, YOU MUST MONITOR ANDADJUST THE TENSIONING DEVICES TO MAKE SURE THAT THE LOADSAPPLIED ARE NOT MORE THAN THE MAXIMUM LOADS.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
During the lifting operations of a damaged aircraft with cranes, jacks and/or pneumatic lifting bags,you should tether the aircraft to prevent horizontal movement due to lifting side force (weight of theaircraft, wind force, etc...).You can attach the tether to fabric straps installed around the fuselage or the engine pylons or todifferent fittings such as pylon hoist fittings, fuselage fittings and vertical stabilizer fittings.To make sure that the horizontal stability is satisfactory, it is necessary to safely attach the aircrafttethering cables to heavy vehicles or to a deadman anchors tightly attached to the ground. Thetethers should make different angles with the fuselage centerline to prevent aircraft movement in allthe directions.A tensioning device should be provided for each tethering line so that tension is satisfactory at eachtether during the lifting operation.The number of tethers changes with the type of recovery operation and is related to the strength anddirection of the wind.See FIGURE 04-30-00-991-001-A for wind loads applied on the aircraft on ground.
**ON A/C A318-100 A319-100
2. Tethering Using the Mooring FittingsMooring fittings can be installed on the fuselage. See FIGURE 04-30-00-991-002-AFIGURE04-30-00-991-002-B for the location of the Mooring fittings.At each position, remove the blanking screws and the remaining sealant before you install themooring fitting.
04-30-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Tethering Position Fitting P/N - Item
FR8 LHFR8 RH
98D07203000 MOORING FITTING - 04098D07203000 MOORING FITTING - 041
FR15 LHFR15 RH
98D07203000 MOORING FITTING - 04298D07203000 MOORING FITTING - 043
FR21 LHFR21 RH
98D07203000 MOORING FITTING - 04498D07203000 MOORING FITTING - 045
FR 30 LHFR 30 RH
98D07203000 MOORING FITTING - 04698D07203000 MOORING FITTING - 047
FR 62/63 LHFR 62/63 RH
98D07203000 MOORING FITTING - 04898D07203000 MOORING FITTING - 050
Mooring Fitting Positions
TABLE 1
**ON A/C A320-100 A320-200 A321-100 A321-200
3. Tethering Using the Mooring FittingsMooring fittings can be installed on the fuselage. See FIGURE 04-30-00-991-002-CFIGURE04-30-00-991-002-D for the location of the Mooring fittings.At each position, remove the blanking screws and the remaining sealant before you install themooring fitting.
Tethering Position Fitting P/N - Item
FR8 LHFR8 RH
98D07203000 MOORING FITTING - 04098D07203000 MOORING FITTING - 041
FR15 LHFR15 RH
98D07203000 MOORING FITTING - 04298D07203000 MOORING FITTING - 043
FR21 LHFR21 RH
98D07203000 MOORING FITTING - 04498D07203000 MOORING FITTING - 045
FR 33 LHFR 33 RH
98D07203000 MOORING FITTING - 04698D07203000 MOORING FITTING - 047
FR 62/63 LHFR 62/63 RH
98D07203000 MOORING FITTING - 04898D07203000 MOORING FITTING - 050
Mooring Fittings Positions
TABLE 2
**ON A/C A318-100 A319-100
4. Tethering Using Straps or CablesYou can install straps or cables around the engine pylons and the fuselage main frames: FR15, 30 and62, 63.
04-30-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
You must install a protection (plywood sheet covered with thick padding) between these straps orcables and the fuselage and engine pylons. You can attach the tethers, tightly connected to theground, to these straps or cables.
**ON A/C A320-100 A320-200 A321-100 A321-200
5. Tethering Using Straps or CablesYou can install straps or cables around the engine pylons and the fuselage main frames: FR15, 32, 33and 62,63.You must install a protection (plywood sheet covered with thick padding) between these straps orcables and the fuselage and engine pylons. You can attach the tethers, tightly connected to theground, to these straps or cables.
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
6. Tether Lines InstallationThe tethering load distribution must be symmetric around the fuselage. For this purpose, you mustinstall the tethering lines on each side of the fuselage.Chapter 04-40-00 gives details on the ground anchors that you can use for tethering the aircraft.FIGURE 04-30-00-991-003-A gives an example of tethering line installation.
04-30-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
Mx
Mz
My
Fz
Fy
Fx
CA
SE
1F
RO
NT
AL
ST
RIK
E
CA
SE
345
° S
TR
IKE
CA
SE
2S
IDE
ST
RIK
E
CA
SE
1: W
ILL
CA
US
E N
OS
E T
O R
ISE
(M
y)C
AS
E 2
: WIL
L C
AU
SE
AIR
CR
AF
T T
O R
OLL
AN
D Y
AW
(M
x +
Mz)
CA
SE
3: W
ILL
CA
US
E A
IRC
RA
FT
TO
RO
LL, Y
AW
AN
D P
ITC
H (
Mx
+ M
z +
My)
N_A
R_0
4300
0_1_
0010
101_
01_0
0
TetheringGround Wind Loads
FIGURE-04-30-00-991-001-A01
04-30-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N_AR_043000_1_0020101_01_00
A C D EB
FR8
FR15 FR21 FR30 FR63FR62
A B C
4 HOLES 7 HOLES 4 HOLES
4 HOLES
4 HOLES
DE
TetheringLocation of the Mooring FittingsFIGURE-04-30-00-991-002-A01
04-30-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
A C EB
FR8
FR15 FR21 FR30 FR63FR62
A B C
4 HOLES 7 HOLES 4 HOLES
4 HOLES
4 HOLES
DE
N_AR_043000_1_0020201_01_00
D
TetheringLocation of the Mooring FittingsFIGURE-04-30-00-991-002-B01
04-30-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
N_AR_043000_1_0020301_01_00
A B C
4 HOLES 7 HOLES 4 HOLES
4 HOLES
4 HOLES
DE
A EB
FR8
FR15 FR21 FR63FR62
DC
FR33
TetheringLocation of the Mooring FittingsFIGURE-04-30-00-991-002-C01
04-30-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_AR_043000_1_0020401_01_00
A B
4 HOLES 7 HOLES 4 HOLES
4 HOLES
4 HOLES
DE
A EB
FR8
FR15 FR21 FR63FR62
DC
FR33
C
TetheringLocation of the Mooring FittingsFIGURE-04-30-00-991-002-D01
04-30-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_043000_1_0030101_01_00
TetheringTypical Tethering Lines Installation
FIGURE-04-30-00-991-003-A01
04-30-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 04-30-00-556-801-A01
Mooring
1. GeneralDuring the recovery operation, you can moor the aircraft to help the tethering.
2. InspectionsMake sure that there is no damage on the landing gears.
3. Job Setup References
A. PreparationMake sure that the landing gear safety devices are in position (see TASK 02-30-01-200-801-A01).Install the wheel chocks in front and behind the wheels.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATION98D10203500 MOORING KIT - NLG
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-200-801-A01 TASK 02-30-01-200-801-A01-Landing Gear Survey
04-40-00 04-40-00-GROUND ANCHORSFIGURE 04-30-00-991-004-A FIGURE 04-30-00-991-004-A-Mooring on the Nose Landing
Gear
Referenced Information
TABLE 2
5. Procedure
Subtask 04-30-00-556-001-A01
A. Mooring of the Nose Landing Gear
(1) With the mooring kit
(a) Put the 98D10203500 MOORING KIT - NLG in position.See FIGURE 04-30-00-991-004-A.See 04-40-00 for details on the ground anchors.
04-30-00Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(2) With ropes
(a) Attach the ropes (3) and (4) of a diameter of 50.8 mm (2.0 in) on the towing lug andthe debogging lug of the nose landing gear.
NOTE : If manila or sisal rope is used, make sure that there is not too much tensionon the rope because contraction can occur in wet weather.
(b) Attach the other ropes (2) of a diameter of 50.8 mm (2.0 in).
(c) Attach all the ropes on the ground with the mooring points. Put tension on thisassembly.
Subtask 04-30-00-556-002-A01
B. Mooring on the Main Landing Gears with Ropes
(1) Attach the ropes (3) and (4) of a diameter of 50.8 mm (2.0 in) on the towing lug and thedebogging lug of the main landing gear.
NOTE : If manila or sisal rope is used, make sure that there is not too much tension onthe rope because contraction can occur in wet weather.
(2) Attach the ropes on the ground with the mooring points. Put tension on this assembly.
04-30-00Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
BN_AR_043000_1_0040101_01_00
A
TOWING FITTING
GROUND ANCHOR
TOWING FITTING
B
AFWD
Mooring on the Nose Landing GearNLG Mooring Kit
FIGURE-04-30-00-991-004-A01
04-30-00Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_043000_1_0050101_01_00
A
21
GROUND ANCHOR
A
TOWING FITTING
Mooring on the Nose Landing GearInstallation of the Mooring RopesFIGURE-04-30-00-991-005-A01
04-30-00Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
A
DEBOGGING LUG
TOWING LUG
4
3
AFWD
N_AR_043000_1_0060101_01_00
Mooring on the Main Landing GearInstallation of the Mooring RopesFIGURE-04-30-00-991-006-A01
04-30-00Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_043000_1_0070101_01_00
SHORT ROPE FWDOF NOSE LANDING GEAR
45°
TYPICAL ALLPOSITIONS
MooringPosition of the Mooring RopesFIGURE-04-30-00-991-007-A01
04-30-00Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
04-40-00 GROUND ANCHORS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 04-40-00-001-A01
General
1. Ground Anchors for Tethers
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
There are three basic ways of supplying anchors for the tether lines:- Commercial type ground anchors,- Dead-man anchors,- Heavy vehicles.
A. Commercial Type Ground AnchorsThere are several types of commercially manufactured ground anchors on the market. Beforeinstallation of any type of ground anchor the manufacturer’s instructions must be reviewed andthe stability of the soil must be analyzed. Different sizes of these anchors are available to caterfor the various loads. Most anchor units must be hammered or turned to a necessary depthdepending on the stability of the soil. Generally longer models are required for loose soils andshorter ones for harder soils.
B. Dead-Man AnchorsDead-man anchors are those constructed on the site from available materials such as vehiclewheels complete with tires, heavy cribbing timbers or railroad ties. A hole is excavated to anadequate depth and the materials are buried after being attached to cables. The hole is thenback-filled with the cables forming an angle of approximate of 30 degrees between the wheel ortimber and the ground. Use of this type of anchors requires a good experience of their use toensure adequate strength.
C. Heavy VehiclesIt is possible to use large and/or heavy vehicles, if there is an adequate supply. Once the vehicleis used as anchor, it cannot be used for its original purpose during the recovery operation.
2. Anchor Holding Capacity
A. Anchor holding capacity is dependent on the type of soil and the depth of the anchor.
B. The holding capacity of the anchor will decrease as the moisture content of the soil increases.
C. It is necessary to test the soil stability:- Evaluate the type of anchoring method,- Determine the holding capacity of a given anchor in various soil types.
D. The soil stability can be tested in the field using a number of portable soil test probes.
04-40-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
04-50-00 SOIL STABILITY
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 04-50-00-001-A01
General
1. Soil stability is of prime importance to ensure personnel safety, avoidance of secondary damage,selection of ground corrective action or of tooling to be used to allow implementation of the recoveryprocedure.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
Basically you must make sure that ground remains stable for the intended purpose and keep in mindthat load bearing capacity of soil might change with weather conditions.
04-50-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
WEIGHT REDUCTION
05-00-00 WEIGHT REDUCTION
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-00-00-001-A01
General
1. You must control aircraft weight.
WARNING : PUT SAFETY DEVICES ON THE CARGO DOOR OPENING MECHANISM TOPREVENT UNWANTED CLOSURE OF THE DOOR.
WARNING : YOU MUST CONTROL ALL MOVEMENT OF THE PAYLOAD DURING REMOVALTO PREVENT TAIL TIPPING.
WARNING : YOU MUST CONTROL MOVEMENT AND SPEED OF CONTAINERS ANDPALLETS TO PREVENT RAPID MOVEMENT OF PAYLOAD BECAUSE OFAIRCRAFT ATTITUDE.
WARNING : YOU MUST MONITOR CHANGE TO CG AND AIRCRAFT ATTITUDE DURINGREMOVAL OF PAYLOAD.
Aircraft weight change will affect CG, aircraft stability and expected loads. It is commonly acceptedthat NRW should be the minimum possible, which implies removal of maximum weight.Make sure that actions taken to reduce weight have an efficient effect.Make sure that you get the expected results.You can get maximum weight reduction if you remove weight from:- Fuel tanks- Cargo compartments.
NOTE : For disposition and locations of containers and pallets in the cargo compartments, see09-10-14.
Sometimes, it is not necessary to remove the cargo payload or fuel. This depends on main factorssuch as:- CG control- Weight and amount of the cargo payload on board- Need to excavate and build roadways for access- Need to stabilize the ground so that cargo loaders and fuel trucks can go near the aircraft- Expected removal: defueling time versus the time requirements to move the aircraft- Capacity of the available lifting means- Expected leveling/lifting loads- Structural limitations on allowable leveling/lifting loads- On-site storage capability of removed fuel.Fuel and cargo payload can also remain on the aircraft to be used as ballast.
05-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
NOTE : Always be prepared for sudden attitude changes of the aircraft as the payload or fuel, etc.is removed. The changes can affect both the longitudinal and lateral axes of the aircraft.
For Fuel Weight Reduction see 05-10-00.For Cargo Weight Reduction see 05-50-00.
05-00-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-10-00 DEFUELING
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-10-00-001-A01
General
1. DefuelingDefueling is one of the most important tasks to be carried out during an aircraft recovery operation.The importance relates not only to weight reduction, but also to control of the Center of Gravity(CG). The total mass of fuel on board the aircraft can be many tons. When the aircraft is in anabnormal attitude a significant shift in CG can take place as the aircraft is returned to a normalattitude. The procedures chosen to defuel a disabled aircraft should be made only after a thoroughinvestigation has been carried out to determine:- The aircraft attitude- The extent of damage to the structure and the functional status of the fuel and electrical
systems. The ability to energize the aircraft electrical power system through an external groundpower source (or the aircraft batteries) will reduce the total time required for the defuel process.The lack of electrical power due to an inoperative electrical system, is the most common problemassociated with the defuel process.
The defuel system uses the same valves and fuel lines as the refuel system and components of theengine feed and transfer systems. The aircraft can be defueled through one or more of the four hoseadapter couplings at the wing leading edges.The quantity of fuel removed will vary considerably dependant on the aircraft attitude and themethod used to defuel.Sufficient storage for the removed fuel must be available. This is a very important issue speciallywhen large amounts of fuel are involved. If the aircraft was involved in an incident where fuelcontamination is suspected, it is necessary to quarantine the removed fuel. Only when the applicableauthorities have made sure that this fuel is safe to use can it be used according to company and stateregulations.Remove as much fuel as is possible prior to lifting the aircraft.Large quantities of fuel can be trapped in the tanks due to abnormal aircraft attitudes. It is possiblethat this fuel cannot be removed until the aircraft is level.When one main landing gear has collapsed (or is deeply bogged in mud) the transfer of fuel from thelow wing to the opposite wing will reduce the weight of the low wing. This weight reduction will shiftthe CG of the opposite wing outboard from the main landing gear. This transfer process is onlyavailable when the fuel system is intact and power can be supplied to the fuel pumps and valves.The defuel process may have to be carried out in several steps, as the aircraft is levelled andstabilized several times.
05-10-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Although the removal of the fuel is important, not all recovery operations will require its removal.Where relatively small quantities of fuel remain, it is not necessary to remove it. This decision canonly be made once the survey has been completed. Decisions can also be made to reduce weight onlyto the point where maximum lifting and jacking loads will not be exceeded. This is not arecommended procedure and should be evaluated thoroughly.
2. General Preparation
WARNING : MAKE SURE THAT YOU OBEY ALL THE APPLICABLE SAFETY PRECAUTIONSWHEN YOU REMOVE FUEL OR WHEN YOU WORK IN AN ENVIRONMENTWHERE THERE IS FUEL.
WARNING : DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUELON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSES FIRE.
Before you start the defuel, you must make sure that:
A. You obey all the safety precautions applicable to refuelling/defuelling.
B. The safety area is clearly identified and the tankers are in correct position, see FIGURE05-10-00-991-004-A.
C. The aircraft is correctly grounded, see 09-10-13.
D. A ground cable connects the tanker to the MLG ground connection.
E. There are no open flames or smoking in the safety area.
F. Only personnel qualified to do the defuel operation are in the safety area.
G. All the equipment and material not necessary for the defuel procedure are moved out of thesafety area.
H. The correct safety and fire fighting equipment is in position with the qualified personnel tooperate it.
J. The escape lanes for the fuel tankers are clear of obstruction.
K. The fuel tankers have sufficient capacity for the quantity to be defueled.
L. Only the electrical equipment necessary for the defuel procedure is used.
M. You do not operate the aircraft main engines or the APU during the defuel procedure.
N. The electrical equipment you use will not create a spark.
P. Caps are installed on all damaged fuel pipes.
Q. All damaged electrical wiring and fuel pumps are isolated.
R. You only use pumps that are serviceable.
S. Do not do the defuel procedure in bad weather conditions. Lightning is dangerous.
T. Do not operate radio, radar equipment or mobile phone during the defuel procedure.
U. Immediately remove all fuel spillage in accordance with local procedures.
05-10-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
V. You have stopped all fuel leaks.
W. Trained personnel are available to contain all fuel spills.
X. If necessary put a GPU in position as far as practicable from the A/C. The GPU must have 3phases, with 115 Volts AC, 400 Hz and 20 KVA.
05-10-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
SAFETY AREA
THIS AREA MUST BE KEPTCLEAR TO LET THETANKER MOVE AWAY INAN EMERGENCY
NOTE: THIS AREA MUST BE KEPTCLEAR TO LET THETANKER MOVE AWAY INAN EMERGENCY
NOTE:
DIMENSIONS IN METERS(FEET IN BRACKETS)
NOTE:
NOTE: ALL SAFETY ZONECLEARANCES ARESUBJECT TO CHANGEACCORDING TO LOCALOR AIRPORTREGULATIONS
15(49)
15(49)
15(49)
15(49)
15(49)
15(49)
15(49)
15(49)
7(23)
7(23)
TANKER TANKER
N_AR_051000_1_0040101_01_00
DefuellingSafety Area
FIGURE-05-10-00-991-004-A01
05-10-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-20-00 FUEL SYSTEM DESCRIPTION
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-20-00-001-A01
Fuel System Basic Description
1. Basic DescriptionThe fuel system:- controls and supplies fuel in the correct quantities to the fuel tanks during refuel operations,- supplies fuel to the engines via the engine feed tanks during flight,- supplies fuel to the Auxiliary Power Unit (APU),- gives indications in the cockpit of system operation,- gives indications in the cockpit of a malfunction in the system that could cause an unusual
condition,- controls defuel and fuel ground transfers.See DESC 09-10-12-004-A01 for the ground service connections (refuel/defuel coupling andrefuel/defuel control panel).
05-20-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-20-00-002-A01
Tanks
**ON A/C A318-100 A319-100 A320-100 A320-200
1. The A318/A319/A320 has the following fuel tanks:
Tank Capacity
liters US GallonsOuter Wing Tank LH 880 232
Outer Wing Tank RH 880 232
Inner Wing Tank LH 6924 1829
Inner Wing Tank RH 6924 1829
Centre Tank 8250 2179Total fuel capacity 23859 6303
Tank Capacities
TABLE 1
NOTE : On A319 and A320, Additional Centre Tanks (ACT) can be installed with a capacity of2992 l (790 US gal) per tank.
**ON A/C A321-100 A321-200
2. The A321 has the following fuel tanks:
Tank Capacity
liters US GallonsWing Tank LH 7750 2047
Wing Tank RH 7750 2047
Centre Tank 8200 2166Total fuel capacity 23700 6261
Tank Capacities
TABLE 2
NOTE : On A321, Additional Centre Tanks (ACT) can be installed with a capacity of 2900 l (766US gal) per tank.
05-20-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
3. Each tank has one or more water drain valves. These are used to:- drain the water, which could possibly come out of the fuel in the tank- drain the fuel that remains after a defuel procedure has been completed (for maintenance).
4. All of the fuel tanks are fueled/defueled through a standard 2.5 inch fuel coupling, located in theright wing leading edge.
5. Each wing tank is vented through the vent/surge tanks.
6. The system uses the fuel transfer-pump to move the fuel.
7. The FQIC (Fuel Quantity Indication Computer) automatically controls the system, but if necessary,the system can be manually controlled in the cockpit.
8. The fuel is delivered to the engines by booster pumps (2 per tank).
05-20-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200
VENT/SURGE TANKVENT/SURGE TANK
CENTER TANK
OUTER TANK
INNER TANK INNER TANK
OUTER TANK
N_AR_052000_1_0130101_01_00
Fuel SystemFuel Tank General ArrangementFIGURE-05-20-00-991-013-A01
05-20-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
VENT/SURGE TANK VENT/SURGE TANK
WING TANK WING TANK
CENTER TANK
N_AR_052000_1_0130201_01_00
Fuel SystemFuel Tank General ArrangementFIGURE-05-20-00-991-013-B01
05-20-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200
STRAINERSTRAINER
CENTER TANKFUEL PUMP
CENTER TANKFUEL PUMP
CENTER TANKFUEL PUMP
PRESSURE SWITCH
APULP VALVE
APUFUEL PUMPPRESSURE
SWITCH
APUFUELPUMP
CROSSFEEDVALVE
DEFUELTRANSFER
VALVE
REFUELVALVE
CENTER TANKFUEL PUMPPRESSURE
SWITCH
N_AR_052000_1_0010101_01_00
CL
CENTER TANK
Fuel System SchematicCentre Tank
FIGURE-05-20-00-991-001-A01
05-20-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
JET PUMP
DIFFUSER
REFUEL VALVE
DEFUELTRANSFER VALVE
CROSSFEEDAPUFUEL PUMP
APU LP VALVE
RIB1
APU FUEL PUMPPRESSURE SWITCH
CENTERTRANSFER
TANK
CL
VALVE
CONTROL VALVE
N_AR_052000_1_0010201_01_00
Fuel System SchematicCentre Tank
FIGURE-05-20-00-991-001-B01
05-20-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200
STRAINER
REFUEL GALLERY
VALVE ACTUATOR (SINGLE MOTOR)
VALVE ACTUATOR (TWIN MOTOR)
JET PUMP
FLOAT VALVE
VENT SYSTEM FUEL DRAIN VALVE
WATER DRAIN VALVE
FUEL QUANTITY INDICATOR PROBE
TEMPERATURE SENSOR
HIGH LEVEL SENSOR
CHECK VALVE ( DIRECTION OF FLOW)
CLACK VALVE ( DIRECTION OF FLOW)
LEGEND
DIFFUSER
PRESSURE RELIEF VALVE
SOLENOID OPERATED VALVE
OVERPRESSURE PROTECTOR
MAGNETIC FUEL LEVEL INDICATOR (MLI)
LOW LEVEL SENSOR
SENSOR
CADENSICON
AIRRELEASE
VALVE
LP VALVE
FUEL SUPPLY PIPE
ENGINE CENTER TANK VENT PIPE
MAIN FUEL PUMPS
SEQUENCE VALVES
STRAINER
MAIN FUEL PUMPPRESSURE SWITCH
FUEL DRAINVALVE
SUCTIONVALVE
N_AR_052000_1_0020101_01_00
RIB2
RIB11RIB9
RIB8
RIB6
RIB4
RIB1
CL
Fuel System SchematicInner and Outer Wing Tanks (Sheet 1 of 2)
FIGURE-05-20-00-991-002-A01
05-20-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200
FROMTHE
SURGETANK
WING TANK VENT DUCT
REFUEL/DEFUEL COUPLINGR/H STANDARDL/H OPTIONAL
REFUEL VALVE
AIR INLET VALVE
OVERWING REFUEL ADAPTOR
NACA VENT INTAKE
FUEL VENTPROTECTOR
REFUELSPILLPIPE
PRESSUREHOLDING
VALVE
WING TANKVENT DUCT
RECIRCULATIONPIPE
INNER TANK
OUTER TANK
RIB17
RIB16
RIB15
RIB14
RIB16
RIB11
RIB13
RIB15
RIB17
RIB19RIB21
RIB22
RIB23RIB25RIB27
RIB14
FROM THE MAIN FUEL PUMPS
WING TANK
N_AR_052000_1_0020102_01_00
Fuel System SchematicInner and Outer Wing Tanks (Sheet 2 of 2)
FIGURE-05-20-00-991-002-A01
05-20-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
VALVE ACTUATOR (SINGLE MOTOR)
VALVE ACTUATOR (TWIN MOTOR)
JET PUMP
FLOAT VALVE
VENT SYSTEM FUEL DRAIN VALVE
WATER DRAIN VALVE
FUEL QUANTITY INDICATOR PROBE
TEMPERATURE SENSOR
HIGH LEVEL SENSOR
LOW LEVEL SENSOR
CHECK VALVE ( DIRECTION OF FLOW)
CLACK VALVE ( DIRECTION OF FLOW)
LEGEND
DUALCOMP
DIFFUSER
PRESSURE RELIEF VALVE
ULTRACOMP
SENSOR
SOLENOID OPERATED VALVE
OVERPRESSURE PROTECTOR
MAGNETIC FUEL LEVEL INDICATOR (MLI)
OVERWING REFUEL ADAPTOR
AIR INLET VALVE
REFUEL VALVE
AIR INLET PIPE
DIFFUSER
REFUEL/DEFUEL COUPLINGR/H STANDARDL/H OPTIONAL
NACA VENT INTAKE
FUEL VENT PROTECTOR
CLACK VALVE
PRESSURE HOLDING VALVE
WING TANK VENT DUCT
RECIRCULATIONPIPE
T
RIB11
RIB14
RIB16
RIB23
RIB27
RIB25RIB22
RIB21
RIB19
RIB17
RIB13
RIB15
WINGTANK
N_AR_052000_1_0020201_01_00
Fuel System SchematicWing Tanks (Sheet 1 of 2)
FIGURE-05-20-00-991-002-B01
05-20-00Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
STRAINER FUEL DRAINVALVE
MAIN FUEL PUMPPRESSURE SWITCH
MAIN FUEL PUMPS
STRAINER
AIRRELEASE
VALVE
LP VALVE
ENGINE
CHECK VALVE
REFUEL GALLERY
FUEL SUPPLY PIPE
CENTER TANK VENT PIPE
T
SUCTIONVALVE
RIB2
RIB1
RIB4
RIB6RIB8
RIB9
RIB11
N_AR_052000_1_0020202_01_00
CL
Fuel System SchematicWing Tanks (Sheet 2 of 2)
FIGURE-05-20-00-991-002-B01
05-20-00Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-20-00-004-A01
Fuel Quantity Indicating System
1. The Fuel Quantity Indicating (FQI) system measures the total quantity of fuel in the fuel tanks. Itgives indications for these areas:- The LH and RH wing tanks,
For A318, A319 and A320, it gives indications for the inner and outer tank.- The center tank,- The ACT, if installed- Fuel on board (FOB).
2. The Magnetic Level Indicator (MLI) provides a secondary method to measure the fuel quantity.See TASK 03-20-02-970-801-A01.
05-20-00Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
FUEL SYSTEMPAGE
PUSHBUTTONSWITCH
A
B
CN_AR_052000_1_0140101_01_00
ECAM SDUFUEL SYSTEM PAGE(TYPICAL DISPLAY)
LEFT RIGHT
APU
FOBF.USED 1 F.USED 2
3100 3100
5030 50302800
−11−11
CTR
FUEL
750 750
14360
KG
°C + 10 °C+ 10
ECAM CONTROL PANEL 11VU
OFF BRT
UPPER DISPLAY
LOWER DISPLAY
ECAM
OFF BRT
PRESS HYD ELEC FUEL
APU COND DOOR F/CTL WHEEL ALL
CLR STS RCL CIR
ENG BLEED
TOCONFIG CANC
B
A
C
FUEL CONTROL PANEL 40VU
FUELA
UTO
ENG 1
MODE SEL1 2
FUEL
APUX FEED
ENG 2
1 2CTR TKCTR TKL TK PUMPS R TK PUMPS
PUMP 1 PUMP 2
OFF
FAULT
OFF
FAULT
OFF
FAULT
OFF
FAULT
OFF
FAULT
OFF
FAULT
MAN
FAULT
ON
OPEN
Fuel SystemControl and Indications - Typical View
FIGURE-05-20-00-991-014-A01
05-20-00Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_052000_1_0150101_01_00
A
REFUEL/DEFUELCONTROL PANEL
NOTE: DEPENDING ON YOUR AIRCRAFT CONFIGURATION
FUELkg x 1000
QTY
RIGHTCTRLEFT
LEFT CTR RIGHT
LVLHI
OPEN
NORM
SHUT
OPEN
NORM
SHUT
REFUEL VALVESOPEN
NORM
SHUT
BATT POWERTESTHI LVL ON
OPEN LTS NORM
MODE SELECTREFUEL
OFF
DEFUEL / XFR
kg x 1000
PRESELECTED
DEC INC
ACTUALREFUEL
CKPT END
A
Refuel/Defuel Control PanelTypical View
FIGURE-05-20-00-991-015-A01
05-20-00Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-30-00 MOVING FUEL FOR CG CONTROL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 05-30-00-650-801-A01
Fuel Transfer
1. General
WARNING : DO NOT TRY TO GET ACCESS TO THE FUEL VALVE ACTUATORS IN ALANDING GEAR BAY IF THE RELATED GEAR IS RETRACTED AND THE GEARDOORS ARE CLOSED. IN THIS CONDITION, THE WEIGHT OF THE LANDINGGEAR CAN BE ON THE GEAR DOORS. IF YOU OPEN THESE GEAR DOORS,THERE IS A RISK THAT THE LANDING GEAR WILL EXTEND BY GRAVITY.
WARNING : MAKE SURE THAT THE AIRCRAFT IS STABLE AND SAFE BEFORE YOU TRYTO GET ACCESS TO THE FUEL SYSTEM VALVES OR OTHER COMPONENTS.
WARNING : THIS PROCEDURE IS FOR INFORMATION ONLY TO HELP YOU PREPARE THERECOVERY OPERATION. TO DO THE PROCEDURE, YOU MUST REFER TO THEOPERATORS CUSTOMIZED DOCUMENTATION.
CAUTION : BEFORE YOU TRANSFER FUEL, MAKE SURE THAT THERE IS SUFFICIENTSPACE IN THE APPLICABLE TANKS FOR THE FUEL YOU WILL TRANSFER.
CAUTION : WITHOUT A SERVICEABLE ELECTRICAL SYSTEM, YOU MUST MONITOR THEQUANTITY OF FUEL IN THE TANKS AND MAKE SURE TO STOP THETRANSFER TO A TANK WHEN THE FUEL IN THE TANK IS NEAR THE HIGHLEVEL QUANTITY.THERE IS NO HIGH LEVEL PROTECTION FOR THE TANKS IF THEELECTRICAL SYSTEM IS NOT SERVICEABLE.
If the aircraft is in a wing high position, it can be necessary to transfer fuel from the low wing to thehigh wing. This helps to move the aircraft lateral CG to the correct position.Before you do a fuel transfer, you must find the fuel quantity in each fuel tank.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONAMM 28-00-00-910-001AMM 24-41-00-861-002
05-30-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
REFERENCE DESIGNATIONAMM 31-60-00-860-001
Referenced Information
TABLE 1
5. Procedure
Subtask 05-30-00-869-001-A01
A. Preparation
(1) Obey the fuel safety procedures when you work on the fuel system. See AMM28-00-00-910-001.
(2) Put safety barrier in position and a warning notice to tell persons not to operate the flightcontrols.
(3) Energize the aircraft electrical circuits (see AMM 24-41-00-861-002) and do an EIS startprocedure (lower ECAM DU) (see AMM 31-60-00-860-001).
(4) On the ECAM control panel push the FUEL pushbutton switch (P/BSW) to show theFUEL page.
(5) Open the access door192MB.
Subtask 05-30-00-650-003-A01
B. Fuel Transfer
(1) On the refuel/defuel panel 800VU:
(a) Hold the TEST switch in the LTS position and make sure that:- all the panels lights come on,- the FUEL QTY and REFUEL displays show figure eights.
(b) Hold the TEST switch in the HI LVL position and make sure that all the HI LVLlights change state. That is, those that were off come on and those that were on gooff.
(c) Release the TEST switch and make sure that the HI LVL lights, for the tanks whichare not full, go off.
(d) Put the MODE SELECT switch to the DEFUEL XFR position and make sure that theOPEN light comes on.
(e) To move the fuel from on of the wing tanks:- put the REFUEL VALVES switch of the tank you are to move fuel from, to the
NORM and guarded position,- put the REFUEL VALVES switch of the tank you are to move fuel into, to the
OPEN position.
05-30-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(f) On the fuel control panel 40VU:- push the X FEED P/BSW,- make sure that the P/BSW ON and OPEN lights come on.
(g) On the ECAM SDU, make sure that the crossfeed valve shows green in-line (open).
(2) To move fuel from the wing tanks:
(a) On the fuel control panel 40VU:- push the applicable TK PUMPS P/BSWs,- make sure that the applicable P/BSW OFF lights go off.
(b) On the ECAM SDU monitor the fuel quantity indications.
(c) When the fuel quantity indications are correct, on the fuel control panel 40VU:- release the applicable P/BSW,- make sure that the applicable P/BSW OFF lights come on.
(3) To move all the fuel from a wing tank:
(a) On the fuel control panel 40VU, push the L (or R) TK PUMPS 1 and 2 P/BSWs.Make sure that the applicable P/BSW OFF lights go off.
(b) Operate the pumps until the FAULT lights of the L (or R) TK PUMPS 1 and 2P/BSW come on.
(c) Release the L (or R) TK PUMPS 1 and 2 P/BSWs. Make sure that the applicableP/BSW OFF lights come on and the applicable FAULT lights go off.
(4) To move fuel from the centre tank:
(a) On the control panel 40VU:
1 Release the MODE SEL P/BSW.
2 Make sure that the P/BSW MAN light comes on.
NOTE : You can only transfer fuel from the center tank with the centre tankpumps in manual control.
3 Push the CTR TK PUMPS 1 an 2 P/BSWs. Make sure that the P/BSW OFFlights go off.
(b) On the ECAM SDU, monitor the fuel quantity indications.
(c) When the fuel quantity indications are correct, on the fuel control panel 40VU:- release the CTR TK PUMPS 1 and 2 P/BSWs,- make sure that the P/BSW OFF lights come on and that the P/BSW FAULT
lights go off.
(5) To move all the fuel from the center tank:
(a) On the fuel control panel 40VU, push the CTR TK PUMPS 1 and 2 P/BSWs. Makesure that the P/BSW OFF lights go off.
05-30-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(b) Operate the pumps until the FAULT lights of the CTR TK PUMPS 1 and 2 P/BSWcome on.
(c) Release the CTR TK PUMP P/BSW. Make sure that the P/BSW OFF lights comeon and the P/BSW FAULT lights go off.
05-30-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-40-00 DEFUEL SCENARIOS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-40-00-001-A01
Defuel Scenarios
1. You can use one of the procedures that follow to defuel the aircraft:
A. Normal pressure defuel (with aircraft fuel pumps), with all systems serviceable, see TASK05-40-01-650-801-A01.
B. Drain remaining fuel, see TASK 05-40-02-650-801-A01.
C. Pressure defuel, using an External Wiring Harness (EWH) to supply power to the aircraft fuelpumps, see TASK 05-40-03-650-802-A01.
05-40-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-40-01 DEFUEL SCENARIO 1 NORMAL PRESSURE DEFUEL WITH ALL AIRCRAFT SYSTEMSSERVICEABLE
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 05-40-01-650-801-A01
Normal Pressure Defuel With All Aircraft Systems Serviceable
1. GeneralYou can use this procedure when the aircraft fuel pumps and electrical systems are serviceable. Butonly use this procedure when there is no structural damage and all systems are serviceable.
2. InspectionsNot Applicable.
3. Job Setup ReferencesSee DESC 05-10-00-001-A01 for general preparation before you start the defuel procedure.See DESC 09-10-12-004-A01 for the fuel system ground connections.See AMM 28-25-00-650-001 for the customized procedure.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 05-40-02-650-801-A01 TASK 05-40-02-650-801-A01-Drain Remaining Fuel
DESC 05-10-00-001-A01 DESC 05-10-00-001-A01-GeneralDESC 09-10-12-004-A01 DESC 09-10-12-004-A01-Fuel System
AMM 28-25-00-650-001AMM 24-41-00-861-002
Referenced Information
TABLE 1
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : MAKE SURE THAT YOU OBEY ALL THE APPLICABLE SAFETY PRECAUTIONSWHEN YOU REMOVE FUEL OR WHEN YOU WORK IN AN ENVIRONMENTWHERE THERE IS FUEL.
05-40-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
WARNING : DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUELON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSES FIRE.
Subtask 05-40-01-869-001-A01
A. Preparation
(1) Make sure that the aircraft and the tanker are correctly grounded and bonded.
(2) Open the access door 192MB.
(3) Put access platforms and safety barriers in position.
(4) Remove the applicable refuel coupling cap.
(5) Make sure that the hose-coupling of the fuel tanker/pump is clean.
(6) Make sure that there is no damage on the refuel/defuel coupling. In case of any damage,contact AIRBUS.
(7) Connect the hose-coupling of the fuel tanker/pump to the A/C refuel/defuel coupling.
(8) Energize the A/C electrical circuits, see AMM 24-41-00-861-002.
(9) Start the ECAM system.On the ECAM Control Panel, push the FUEL system page P/BSW.
(10) On the refuel/defuel control panel 800VU:
(a) Make sure that the refuel valve switches are in the NORM and guarded position.
(b) Put the MODE SELECT switch to the DEFUEL XFR position and make sure that theOPEN light comes on.
(11) On the panel 40VU, push the X FEED P/BSW and make sure that the ON and OPENlights come on.
(12) On the SD FUEL page, make sure that the crossfeed valve indication is shown green in-line(valve open).
Subtask 05-40-01-650-003-A01
B. Pressure Defuel Procedure
WARNING : THIS PROCEDURE IS FOR INFORMATION ONLY TO HELP YOU PREPARETHE RECOVERY OPERATION. TO DO THE PROCEDURE, YOU MUSTREFER TO THE OPERATORS CUSTOMIZED DOCUMENTATION.
(1) On the panel 40VU:
(a) Push the MODE SEL P/BSW. Make sure that the MAN light goes off (CTR tankpumps now in automatic control).
(b) Push the applicable TK PUMPS P/BSWs. Make sure that the applicable P/BSWOFF lights go off.
(2) On the SD FUEL page, monitor the fuel quantity indications.
05-40-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(3) When the fuel quantity has decreased to the necessary level, on panel 40VU:
(a) Release the applicable TK PUMPS P/BSWs. Make sure that the related P/BSW OFFlights comes on.
(b) Release the MODE SEL P/BSW. Make sure that the MAN light of the P/BSWcomes on (CTR tank pumps now in manual control).
(c) On the SD FUEL page, make sure that the tank contents become stable.
(4) To defuel the tanks until empty:
(a) Operate the related pumps until the related P/BSW FAULT light comes on.
(b) Release the applicable TANK PUMPS P/BSWs. Make sure that the applicableP/BSW OFF lights come on and the FAULT lights go off.
(5) Drain the remaining fuel from the tank(s), see TASK 05-40-02-650-801-A01.
05-40-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-40-02 DEFUEL SCENARIO 2 DRAIN REMAINING FUEL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 05-40-02-650-801-A01
Drain Remaining Fuel
1. GeneralThis procedure can be used:- to drain the fuel that remains in the fuel tanks.- to defuel the aircraft when no other procedure can be done.
2. InspectionsNot Applicable.
3. Job Setup ReferencesSee DESC 05-10-00-001-A01 for general preparation before you start the defuel procedure.See DESC 09-10-12-004-A01 for the fuel system ground connections.See AMM 28-25-00-650-003 for the customized procedure.To do this procedure, you can use:- 97A28002117002 PURGING TOOL for wing and center tank.
or- 98A28104000002 TOOL - PURGING for center tank only.
or- 98A28203000000 TEST EQUIPMENT JET PUMP for wing and center tank.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATION98A28104000002 TOOL - PURGING
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Devices
on Landing Gears
DESC 05-10-00-001-A01 DESC 05-10-00-001-A01-GeneralDESC 09-10-12-004-A01 DESC 09-10-12-004-A01-Fuel System
AMM 28-25-00-650-003
05-40-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
REFERENCE DESIGNATIONFIGURE 05-40-02-991-004-A FIGURE 05-40-02-991-004-A-Drain Remaining Fuel
Referenced Information
TABLE 2
5. Procedure
WARNING : MAKE SURE THAT ALL PERSONNEL IS AT A SAFE DISTANCE DURING THEREMOVAL OF FUEL, CARGO OR LARGE COMPONENTS. AN UNEQUALREMOVAL OF FUEL OR CARGO OR THE REMOVAL OF LARGE COMPONENTSCAN CHANGE THE CG AND THE LONGITUDINAL AND LATERAL STABILITY OFTHE AIRCRAFT. DEATH OR SERIOUS INJURY MAY RESULT IF THE AIRCRAFTFALLS ON RECOVERY PERSONNEL.
WARNING : MAKE SURE THAT YOU OBEY ALL THE APPLICABLE SAFETY PRECAUTIONSWHEN YOU REMOVE FUEL OR WHEN YOU WORK IN AN ENVIRONMENTWHERE THERE IS FUEL.
WARNING : DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUELON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSES FIRE.
Subtask 05-40-02-869-001-A01
A. Preparation
(1) Make sure that the ground safety locks are installed on the landing gears, see TASK02-30-01-481-801-A01.
(2) On the panel 400VU:- Make sure that the L/G control lever is in the DOWN position.- put a warning notice in position to tell persons not to operate the landing gear.
(3) Put warning notices in position to tell persons not to operate L/G doors.
(4) Put safety barriers and access platforms in position.
(5) If the fuel temperature is less that -5 ˚C (+23.00 ˚F) and/or the water drain valves arefrozen, heat the drain valve areas with an approved hot air blower.
(6) For access to the CTR tank water drain valves, open access panels 195BB and 196BB.
Subtask 05-40-02-650-002-A01
B. Drain Fuel
WARNING : THIS PROCEDURE IS FOR INFORMATION ONLY TO HELP YOU PREPARETHE RECOVERY OPERATION. TO DO THE PROCEDURE, YOU MUSTREFER TO THE OPERATORS CUSTOMIZED DOCUMENTATION.
05-40-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
NOTE : To drain fuel from the center tank, it is recommended to use 98A28104000002 TOOL- PURGING to prevent leaks.
(1) On the PURGING TOOL, fully retract the nut (4), the screw (3) and the plunger assembly(1).
(2) Install the PURGING TOOL, see FIGURE 05-40-02-991-004-A:
(a) Put the hexagonal end of the bush (2) into the base plate of the applicable drainvalve.
(b) Turn the bush (2) through 30 degrees.
(c) Turn the nut (4) until it touches and seals against the surface (wing surface orbottom of the water drain valve).
(d) Put the end of the hose into the container.
(e) Hold the bush (2) and turn the screw (3) to the end of its travel. This causes theplunger (1) to open the drain valve and the fuel to flow.
(3) When the fuel flow stops, hold the bush (2) and turn the screw (3) until the drain valvescloses.
(4) Remove the PURGING TOOL:- Turn the nut (4) until it is clear of the surface (wing surface or bottom of the water
drain valve).- Turn the bush (2) back through 30 degrees and remove the purging tool from the
water drain valve.
(5) Examine the water drain valve for leakage. Leaks are not permitted.
NOTE : To increase the defueling rate, you can use a suction pump driven by an air drill.
05-40-02Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_054002_1_0040101_01_00
HOSE
WATER DRAIN VALVE
OUTLET
TYPICAL SUCTION PUMP
AIR DRILL
HOSE
FUEL TANKBOTTOM−SKIN
(A318/A319/A320 ONLY)23QM
21QM
25QM
95QM 94QM
(24QM)
(22QM)
(26QM)
A
A
1
2
3
4
A
Drain Remaining FuelPurging Tool Installation
FIGURE-05-40-02-991-004-A01
05-40-02Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-40-03 DEFUEL SCENARIO 3 DEFUEL USING AN EXTERNAL WIRING HARNESS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 05-40-03-650-802-A01
Defuel Using an External Wiring Harness
1. General
WARNING : DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUELON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSES FIRE.
WARNING : MAKE SURE THAT THE AIRCRAFT CENTER OF GRAVITY STAYS CORRECTWHEN YOU DEFUEL THE AIRCRAFT. YOU MUST MONITOR THE AIRCRAFT CGAT ALL TIMES
WARNING : BEFORE YOU DO THIS PROCEDURE, MAKE SURE THAT THE AIRCRAFTELECTRICAL SYSTEM IS DE-ENERGIZED AND ISOLATED.
This procedure can be used when:- There is no structural damage to the aircraft,- The aircraft electrical system cannot be energized.
2. InspectionsNot Applicable.
3. Job Setup ReferencesSee DESC 05-10-00-001-A01 for general preparation before you start the defuel procedure.See DESC 09-10-12-004-A01 for the fuel system ground connections.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 05-40-02-650-801-A01 TASK 05-40-02-650-801-A01-Drain Remaining Fuel
DESC 05-10-00-001-A01 DESC 05-10-00-001-A01-GeneralDESC 09-10-12-004-A01 DESC 09-10-12-004-A01-Fuel System
DESC 05-20-00-001-A01 DESC 05-20-00-001-A01-Fuel System Basic Description
FIGURE 05-40-03-991-001-A FIGURE 05-40-03-991-001-A-Defuel Using An External WiringHarness
Referenced Information
TABLE 1
05-40-03Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
Subtask 05-40-03-869-001-A01
A. Preparation
(1) See FIGURE 05-40-03-991-001-A for details on the external wiring harness.
(2) Make sure that the aircraft electrical system is de-energized and isolated.
(3) Make sure that there is no GPU connected to the aircraft electrical system.
(4) Make sure that the aircraft and the tanker are correctly grounded and bonded.
(5) Put access platforms and safety barriers in position.
(6) Remove the applicable refuel coupling cap.
(7) Make sure that the hose-coupling of the fuel tanker/pump is clean.
(8) Make sure that there is no damage on the refuel/defuel coupling. In case of any damage,contact AIRBUS.
(9) Connect the hose-coupling of the fuel tanker/pump to the A/C refuel/defuel coupling.
**ON A/C A318-100 A319-100 A320-100 A320-200
Subtask 05-40-03-010-001-A01
B. External Wiring Harness Installation
(1) The valves that you will use to defuel the aircraft are:- the crossfeed valve 10QM,- the transfer/defuel valve 11QM,- the intercell transfer valves 27QM (29QM) or 28QM (30QM).See DESC 05-20-00-001-A01 for the fuel system description and the location of the valves.
NOTE : The valves can be operated manually if you remove their electrically operatedactuators.
(2) Open the MLG doors.
(3) Open the crossfeed valve 10QM:- Get access to the crossfeed valve actuator 5QM through the MLG door.- Remove the crossfeed valve actuator 5QM.- Engage a suitable tool in the slot of the crossfeed valve 10QM to manually open the
valve.
(4) Open the transfer/defuel valve 11QM:- Get access to the transfer/defuel valve actuator 11QU through the MLG door.- Remove the transfer/defuel valve actuator 11QU.- Engage a suitable tool in the slot of the transfer/defuel valve 11QM to manually open
the valve.
05-40-03Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(5) Operate the intercell transfer valves 27QM (29QM) or 28QM (30QM):
NOTE : When you defuel an outer cell, it is sufficient to open one intercell transfer valve.
(a) Intercell transfer valve operation 27QM (29QM).
1 Remove the access panel 522JB (622JB) to get access to the intercell transfervalve actuator 9QP (10QP).
2 Find the position of the valve using the see/feel indicator on the actuator:
a If the valve is open leave, leave it in the open position.
b If the valve is closed:- Remove the actuator,- Engage a suitable tool in the slot of the drive shaft of the intercell
transfer valve to manually open the valve.
(b) Intercell transfer valve operation 28QM (30QM).
1 Remove the access panel 575DB (675DB) to get access to the intercell transfervalve actuator 11QP (12QP).
2 Find the position of the valve using the see/feel indicator on the actuator:
a If the valve is OPEN leave, leave it in the OPEN position.
b If the valve is closed:- Remove the actuator,- Engage a suitable tool in the slot of the drive shaft of the intercell
transfer valve to manually open the valve.
(6) To defuel the wing tanks, connect the external wiring harness to the pumps 25QA and21QA or 22QA and 26QA:- Remove the pump cover plates from pump 25QA and 21QA to defuel the LH wing.- Remove the pump cover plates from pump 22QA and 26QA to defuel the RH wing.- Remove the electrical plugs from the pumps.- Connect the plugs of the external wiring harness to the pumps 25QA and 21QA or
22QA and 26QA.- Connect the external wiring harness to the GPU.
(7) To defuel the center tank, connect the external wiring harness to the pumps 37QA and38QA:- Get access to the center tank pumps 37QA and 38QA.- Remove the pump cover plates from pump 37QA and 38QA.- Remove the electrical plugs from the pumps.- Connect the external wiring harness plugs to the pumps.
05-40-03Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
Subtask 05-40-03-010-001-B01
B. External Wiring Harness Installation
(1) The valves that you will use to defuel the aircraft are:- the crossfeed valve 10QM,- the transfer/defuel valve 11QM,- the control valves 153QM (154QM).See DESC 05-20-00-001-A01 for the fuel system description and the location of the valves.
NOTE : The valves can be operated manually if you remove their electrically operatedactuators.
(2) Open the MLG doors.
(3) Open the crossfeed valve 10QM:- Get access to the crossfeed valve actuator 5QE through the MLG door.- Remove the crossfeed valve actuator 5QE.- Engage a suitable tool in the slot of the crossfeed valve 10QM to manually open the
valve.
(4) Open the transfer/defuel valve 11QM:- Get access to the transfer/defuel valve actuator 11QU through the MLG door.- Remove the transfer/defuel valve actuator 11QU.- Engage a suitable tool in the slot of the transfer/defuel valve 11QM to manually open
the valve.
(5) Operate the control valves 153QM (154QM):
(a) Remove the access panel 195BB (196BB) to get access to the control valves actuator11QL (12QL).
(b) Find the position of the valve using the see/feel indicator on the actuator:
1 If the valve is OPEN, leave it in the OPEN position.
2 If the valve is closed:- Remove the actuator,- Engage a suitable tool in the slot of the drive shaft of the control valve
153QM ( 154QM) to manually open the valve.
(6) Connect the external wiring harness to the pumps 25QA and 21QA or 22QA and 26QA:- Remove the pump cover plates from pump 25QA and 21QA to defuel the LH wing.- Remove the pump cover plates from pump 22QA and 26QA to defuel the RH wing.- Remove the electrical plugs from the pumps.- Connect the plugs of the external wiring harness to the pumps 25QA and 21QA or
22QA and 26QA.- Connect the external wiring harness to the GPU.
05-40-03Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
Subtask 05-40-03-650-002-A01
C. Defuel Procedure
(1) On the control panel of the external wiring harness, select both pump switches to ON.
(2) Monitor the pumped fuel on the fuel tanker gauge.
(3) Operate the pump until the tank is empty (the fuel flow stops).
(4) On the control panel of the external wiring harness, select both pump switches to OFF.Do not operate the pumps when the fuel tank is empty.
(5) Drain the remaining fuel, see TASK 05-40-02-650-801-A01.
05-40-03Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
SWITCH10 AMPS
OFF
ON
OFF
ON
115VAC
A R
B Y
C B
R
Y
B
16AWG COPPER
16AWG COPPER
16AWG COPPER
P1NSA938 027E15FSN
115VAC
A R
B Y
C B
R
Y
B
P2
PANEL
WIRING DIAGRAM EXTERNAL WIRING HARNESS
EXTERNAL WIRING HARNESS
115VAC
PANEL
P1
P2
30 m (98.3 ft) MINIMUM2.5 m (8
.16 ft)
2.5 m (8.16 ft)
16AWG COPPER
16AWG COPPER
16AWG COPPER
NSA938 028E15FSN
N_AR_054003_1_0010101_01_00
Defuel Using An External Wiring HarnessExternal Wiring Harness
FIGURE-05-40-03-991-001-A01
05-40-03Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-50-00 CARGO COMPARTMENTS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-50-00-005-A01
General
1. See 09-10-14 for the description of the cargo compartments.For data related to the different cargo compartment doors see DESC 09-10-10-003-A01.
05-50-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-50-01 CARGO REMOVAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-50-01-005-A01
Cargo Removal
1. GeneralThis chapter gives data related to the removal of the cargo from the aircraft. The removal of thecargo is an important task carried out during an aircraft recovery operation. Cargo removal willremove a large amount of weight from the aircraft and can also control the Center of Gravity (CG).The procedure you select to remove the cargo during the aircraft recovery operation should only bemade after a survey has been carried out to find:- The aircraft stability and attitude.- The extent of damage to the aircraft structure and components.- The condition of the aircraft electrical systems.- The condition of the cargo loading system.- If an external ground power source is available.- If the equipment necessary to remove the cargo is available.The removal of the cargo is important but not all recovery operations will require its removal. Whena small amount of cargo is loaded it is possible that it is not necessary to remove it. This decision canonly be made once the survey has been completed. Decisions can also be made to remove the cargoonly to the point where the maximum lifting and jacking loads will not be exceeded or the aircraftrecovery operation can be completed.See the Cargo Loading Manual (CLS) for the cargo removal procedure.
05-50-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
05-60-00 REMOVAL OF LARGE COMPONENTS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 05-60-00-001-A01
General
1. Large aircraft components are not usually removed during a recovery operation.
WARNING : YOU MUST CONTACT AIRBUS BEFORE YOU MANUALLY OPERATE A SYSTEMOR REMOVE A COMPONENT WHEN THE AIRCRAFT IS IN AN ABNORMALATTITUDE OR DISABLED. THE AMM PROCEDURES ARE APPLICABLE ON ANAIRCRAFT IN A LEVEL CONFIGURATION ONLY.
Removal can be necessary when:- Damaged components such as flap sections, ailerons, elevators, etc. are not safely attached,- It is necessary to decrease the weight and/or to control CG,- The runway or the airport was closed because of the accident. In this case, it is necessary to
remove the vertical stabilizer. This is an unusual event which can occur only if the runway orairport would be closed for a long time,
- You used escape slides during evacuation. After the evacuation, it is necessary to carefullydisconnect and remove the escape slides,
- Landing gear and/or other components are broken.
05-60-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
LEVELING AND LIFTING
06-00-00 LEVELING AND LIFTING
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 06-00-00-001-A01
General
1. Leveling and Lifting FamiliesThere are 5 basic leveling families (see TBD).
2. Aircraft Pitch and Roll AnglesBefore you start the recovery, it is possible to find the aircraft pitch and roll angles when no electricalpower is available.The items of equipment that you can use are:- An attitude monitor (clinometer), located in the belly fairing- A spirit level, a clinometer or similar device located on the forward cargo-compartment floor
beams or on the cabin floor seat tracks.It is possible to use the same equipment to find when the aircraft is leveled.
3. Leveling/Lifting of the Aircraft
CAUTION : YOU MUST DO THE LATERAL LEVELING BEFORE YOU DO THELONGITUDINAL LEVELING.
There are three general methods to level/lift the aircraft. They are given in the chapters that follow:- Use of Jacks (see 06-30-00),- Use of Pneumatic Lifting Bags (see 06-40-00.),- Use of Cranes (see 06-50-00),- Step by step combination: use of one method and then another one.
A. The leveling/lifting items of equipment are:- Jacks,- Pneumatic lifting bags,- Cranes and slings.It is possible to use one of these items of equipment alone or more than one in any step-by-stepcombination.
B. The procedures in the chapters above describe how to level/lift the aircraft to a height at whichthe fuselage datum is 4600 mm (181.10 in) above the ground. This is the height necessary:- To put the aircraft in a hangar or on maintenance jacks,- To make the extension of the landing gear possible,- To put the aircraft, or part of it, on a mobile device.However, to replace a landing gear, the necessary height of the fuselage datum is 5210 mm(205.12 in) above the ground.
06-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
C. The aircraft can be in such an attitude that it is necessary to do the leveling operation beforethe lifting operation.In this case, you must keep the aircraft in a level attitude during the lifting phase.
NOTE : As each aircraft recovery situation is different, you must analyze the conditions andavailable equipment before you decide which leveling or lifting procedure you will use.
06-00-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 06-00-00-002-A01
Leveling/Lifting Obstructions
1. It may be necessary to remove the items that follow to make the leveling / lifting operation easier.
NOTE : The list is not exhaustive. The optional items of equipment can change as they are relatedto the customer configuration.
Name Zone IPC AMMGPS Antenna 1 & 2 220 IPC 34-36-16 AMM 34-36-16-000-001VHF 1 Antenna 220 IPC 23-12-11 AMM 23-12-11-000-001
ATC Antenna 1 & 2 (Top &Bottom)
120/230 IPC 34-52-11 AMM 34-52-11-000-001
TCAS Antenna (Top & Bottom) 130/230 IPC 34-43-11 AMM 34-43-11-000-001
DME 2 Antenna 120/130 IPC 34-51-11 AMM 34-51-11-000-002
MARKER Antenna 130 IPC 34-55-18 AMM 34-55-18-000-001Angle of Attack Sensors 127/231/232IPC 34-11-19 AMM 34-11-19-000-001
Drain Mast 130 IPC 30-71-51 AMM 30-71-51-000-001
FWD Fuselage
TABLE 1
Name Zone IPC AMMDrain Mast 150 IPC 30-71-51 AMM 30-71-51-000-001Radio Altimeter 1 & 2 150 IPC 34-42-11 AMM 34-42-11-000-001VHF 2 Antenna 150 IPC 23-12-11 AMM 23-12-11-000-001
AFT Fuselage
TABLE 2
06-00-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
FR25 FR35
N_AR_060000_1_0010101_01_00
TCAS TOPATC TOP 1−2VHF 1GPS 2GPS 1
DRAIN MAST
AOA SENSOR 3 ATC BOTTOM 1−2
AOA SENSOR 1−2
DME 2
MARKER
TCAS BOTTOM
FR23
Antennas LocationFWD Fuselage (Sheet 1 of 2)
FIGURE-06-00-00-991-001-A01
06-00-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
FR57 FR69
N_AR_060000_1_0010103_01_00
VHF 2 RA 1 RA 2 DRAIN MAST
Antennas LocationAFT Fuselage (Sheet 2 of 2)
FIGURE-06-00-00-991-001-A01
06-00-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
FR15
FR20 FR34
N_AR_060000_1_0010201_01_00
GPS 1 GPS 2 VHF 1 ATC TOP 1−2
AOA SENSOR 1−2
TCAS TOP
ATC BOTTOM 1−2 DME 2 MARKER
AOA SENSOR 3
TCAS DRAIN MASTBOTTOM
Antennas LocationFWD Fuselage (Sheet 1 of 2)
FIGURE-06-00-00-991-001-B01
06-00-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
FR53 FR62
N_AR_060000_1_0010202_01_00
DRAIN MAST VHF 2 RA 1 RA 2
Antennas LocationAFT Fuselage (Sheet 2 of 2)
FIGURE-06-00-00-991-001-B01
06-00-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200 A321-100 A321-200
FR15
FR20 FR32
N_AR_060000_1_0010301_01_00
GPS 1 GPS 2 VHF 1 ATC TOP 1−2 TCAS TOP
AOA SENSOR 1−2
ATC BOTTOM 1−2
AOA SENSOR 3
DME 2 TCAS BOTTOM DRAIN MAST MARKER
Antennas LocationFWD Location (Sheet 1 of 2)
FIGURE-06-00-00-991-001-C01
06-00-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200 A321-100 A321-200
FR51 FR59
N_AR_060000_1_0010302_01_00
VHF 2 DRAIN MAST RA 1 RA 2
Antennas LocationAFT Fuselage (Sheet 2 of 2)
FIGURE-06-00-00-991-001-C01
06-00-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
06-10-00 LOAD DETERMINATION
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-10-00-970-801-A01
Vertical Loads Determination
1. GeneralThis section gives data about the vertical loads related to aircraft leveling/lifting during the recoveryoperation and about the way to calculate them.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
2. InspectionsNot Applicable.
3. Job Setup References
A. GeneralThe theoretical calculations that follow help to find the loads necessary for leveling/lifting. Theyalso help to:- Make sure the aircraft is stable,- Do a selection of applicable methods of leveling/lifting,- Do a check of the local structural capability of the aircraft to prevent secondary damage,- Make sure the recovery procedure is applicable to the related weight condition of the
aircraft.The simplified calculations are related to the assumptions that follow:- The aircraft structure is considered as rigid. The calculations do not take into account the
flexibility in the aircraft structure,- The leveling/lifting is done at 3 points (isostatic conditions),- The calculation take into account only the vertical loads,- You do the leveling/lifting operations on solid ground conditions and the slings are without
elongation,- The calculation do not take into account the effects of wind and temperature.
B. Location of the 3 lifting points on the aircraft X and Y reference axesSee FIGURE 06-10-00-991-001-A.- For the left wing: X1 and Y1 position of the lifting point,- For the right wing: X3 and Y3 position of the lifting point,- For the fuselage: X2 and Y2 position of the lifting point.
As the fuselage lifting point is located on the aircraft centerline, Y2 = 0.
NOTE : During the leveling/lifting procedure, it can be necessary to use only one lifting point.The aircraft will then pivot around a fixed point such as a main landing gear. Forexample, with the nose landing gear collapsed, there is only one lifting point and theaircraft will pivot around main landing gears.
06-10-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATION03-00-00 03-00-00-WEIGHT AND CG MANAGEMENTFIGURE 06-10-00-991-001-A FIGURE 06-10-00-991-001-A-Load DeterminationFIGURE 06-10-00-991-002-A FIGURE 06-10-00-991-002-A-Load Determination
Referenced Information
TABLE 1
5. Procedure
Subtask 06-10-00-970-001-A01
A. Load Calculation
NOTE : Principle for the calculation of the loads at the recovery leveling/lifting points.
(1) Find the 3 leveling/lifting points and related X and Y values, applicable to the attitude ofthe aircraft and the related scenario (see TBD).
(2) Find the values of the NRW, XG and YG (X and Y coordinates of aircraft CG position)calculated for your aircraft condition (see 03-00-00).
(3) Record these values in the load calculation worksheet (see FIGURE 06-10-00-991-002-A)and calculate the necessary intermediate values.
(4) Use the results of the load calculation worksheet (see FIGURE 06-10-00-991-002-A) to findthe values of the vertical loads (Fz) at the 3 leveling/lifting points.Fz1 = NRW × ((YG - Y2)(X2 - X3) - (XG - X2)(Y2 - Y3)) / ((X1 - X2)(Y2 - Y3) - (Y1 -Y2)(X2 - X3))Fz1 =Fz2 = NRW × ((YG - Y3)(X3 - X1) - (XG - X3)(Y3 - Y1)) / ((X2 - X3)(Y3 - Y1) - (Y2 -Y3)(X3 - X1))Fz2 =Fz3 = NRW × ((YG - Y1)(X1 - X2) - (XG - X1)(Y1 - Y2)) / ((X3 - X1)(Y1 - Y2) - (Y3 -Y1)(X1 - X2))Fz3 =
Subtask 06-10-00-869-001-A01
B. Load Distribution Compared to Allowable Loads
(1) For jacks: You must compare the vertical load directly with the allowable load.
(2) For pneumatic lifting bags:Use the formula that follows to calculate the pressure of the pneumatic lifting bag:p = Fz / (L × W)
06-10-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
L = length and W = width of the pneumatic lifting bag.This pressure must be less than or equal to:- The maximum pressure of the pneumatic lifting bag,- The maximum allowable pressure that the pneumatic lifting bag can apply to the
aircraft structure.
(3) For slings:Use the formula that follows to calculate the load on each sling:f = Fz / NN = number of slings.This load must be less than or equal to the aircraft maximum allowable load at the relatedframe.
NOTE : If loads at leveling/lifting points are not in the allowable values, it is necessary tomake new calculations for the recovery configuration, with:- A modified weight and balance,- A change in the recovery means arrangements,- The use of other applicable recovery methods,- Or any combinations of these modifications.
06-10-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
2540
mm
(100
in)
C L
X3
Y3
Y1
X1
−Y
+X
LIF
TIN
G P
OIN
T
X2
Y2
= 0
NO
TE
:
N_A
R_0
6100
0_1_
0010
101_
01_0
2
Load DeterminationLocation of the 3 Lifting PointsFIGURE-06-10-00-991-001-A01
06-10-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_061000_1_0020101_01_00
XG YGNET RECOVERABLE
X1 Y1LEVELING/LIFTING POINT 1
X2 Y2LEVELING/LIFTING POINT 2
X3 Y3LEVELING/LIFTING POINT 3
X2−X3 X3−X1X1−X2INTERMEDIATE
XG−X2 XG−X3XG−X1
Y2−Y3 Y3−Y1Y1−Y2
YG−Y2 YG−Y3YG−Y1
WEIGHTSEE 03−00−00
SEE 06−00−00
SEE 06−00−00
SEE 06−00−00
CALCULATIONS
Load DeterminationLoad Calculation Worksheet
FIGURE-06-10-00-991-002-A01
06-10-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-10-00-970-802-A01
Side loads on Jack Fittings
1. GeneralThis section gives data about the side loads on jack fittings related to the aircraft leveling/liftingphase during the recovery operation and about the way to calculate them.When you level the aircraft from an unusual attitude, an arc movement (horizontal translation) of thejacking point is related to the displacement.If you use a special recovery jack, the jack head can move along the arc movement. Thus, there areno related side loads applied on the jacking point.If you use a jack that cannot move along the arc movement, the jack will apply side loads to theaircraft structure. If these side loads are more than the allowable loads, they will cause damage to theaircraft structure. It is necessary to calculate the side loads for each leveling/lifting scenario.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 06-10-00-970-801-A01 TASK 06-10-00-970-801-A01-Vertical Loads Determination03-00-00 03-00-00-WEIGHT AND CG MANAGEMENT
Referenced Information
TABLE 1
5. Procedure
CAUTION : BE CAREFUL WHEN YOU USE A JACK THAT CANNOT MOVE ALONG THEARC MOVEMENT. THE JACK WILL APPLY SIDE LOADS TO THE AIRCRAFTSTRUCTURE. IF THESE LOADS ARE MORE THAN THE ALLOWABLE LOADS,THEY WILL CAUSE DAMAGE TO THE STRUCTURE.
Subtask 06-10-00-970-002-A01
A. Load Calculation
(1) Find the aircraft recovery configuration and a leveling/lifting method.
06-10-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(2) Measure the aircraft pitch (β) and lateral (α) angles with one of the tools or the methodthat follow:- An attitude monitor (clinometer), in the belly fairing, 192MB,- A spirit level, a clinometer or equivalent device that can be used on the forward cargo-
compartment floor beams or on the cabin floor seat tracks,- The aircraft geometry and characteristic points.See TBD to find the applicable recovery scenario and the related typical aircraft possibleangles.
NOTE : The typical angles are given as an example. For all scenarios, you must measurethe aircraft pitch and lateral angles for each recovery operation before you startany leveling/lifting procedure. The actual angles are related to the weight andCG configuration of the recovery aircraft.
(3) Calculate the NRW and CG position (see 03-00-00) and calculate the vertical loads (Fz)(see TASK 06-10-00-970-801-A01) at the leveling/lifting point.
(4) Calculate the Fx side load (component on the X axis).Fx = tan β × Fz
(5) Calculate the Fy side load (component on the Y axis).Fy = tan α × Fz
(6) Calculate the resultant (R) of Fx and Fy:R = √(Fx2 + Fy2)
(7) Make sure the resultant R is less than the maximum allowable side load. If the side load isnot less than or equal to the maximum allowable load, you must reduce the applied verticalload until the resultant side load is less than the allowable side load. To reduce the appliedvertical load, you can reduce the weight of the aircraft.
06-10-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-10-00-970-803-A01
Arc Movement Calculation
1. GeneralThis section gives data about the arc movement of the leveling/lifting point related to the aircraftleveling/lifting during the recovery operation and about the way to calculate it.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
2. InspectionsNot Applicable.
3. Job Setup ReferencesWhen you level the aircraft, it will rotate around a fixed pivot point on the ground and this will causemovement along the X or Y axis. This movement is called Arc Movement.You must control this movement during all the recovery procedure.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONFIGURE 06-10-00-991-003-A FIGURE 06-10-00-991-003-A-Arc Movement CalculationFIGURE 06-10-00-991-004-A FIGURE 06-10-00-991-004-A-Arc Movement Calculation
Referenced Information
TABLE 1
5. Procedure
Subtask 06-10-00-970-003-A01
A. Arc Movement Calculation at Fuselage Leveling/Lifting Points
(1) Measurement at Aircraft Basic PositionSee FIGURE 06-10-00-991-003-A.You must make the measurements at the points that follow:- Fixed pivot point: the point around which the aircraft will rotate (X axis).- Fuselage/ground contact point: the contact point between the fuselage and the
ground. This point must be lifted to a level attitude (X axis).- Leveling/Lifting point: the point where you apply the loads and where you calculate the
arc movement (X axis).- Characteristic point: a point on the lower part of fuselage that you will use for angle
calculation (both X and Z axes).
06-10-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(2) Arc Movement Calculation
(a) Calculate the angle:tan β = dz / dxWhere:dx is the distance from the fuselage ground contact point to the characteristic pointon the lower part of the fuselage.dz is the height from the ground to the characteristic point.
(b) Calculate the arc movement.∆X = (L - L’) - √((L - L’)2 + tan2 β × (L’2 - L2))Where:∆X is the arc movement.L is the distance from the fuselage ground contact point to the fixed pivot point (forexample: main landing gear).L’ is the distance from the fuselage ground contact point to the leveling/lifting point.
Subtask 06-10-00-970-004-A01
B. Arc Movement Calculation at Wing Leveling/Lifting Points
(1) Measurement at Aircraft Basic PositionSee FIGURE 06-10-00-991-004-A.You must make the measurements at the points that follow:- Fixed pivot point: the point around which the aircraft will rotate (Y axis).- Wing/ground contact point on the lower wing: the contact point between the wing and
the ground. This point must be lifted to a level attitude (Y axis).- Leveling/Lifting point: the point were you apply the loads and where you calculate the
arc movement (Y axis).- Characteristic point: a point on the lower part of the engine nacelle on the high wing
that you use for angle calculation (the two Y and Z axes).
(2) Arc Movement Calculation
(a) Calculate the angle.tan α = dz / dyWhere:dy is the distance from the wing ground contact point (lower wing) to thecharacteristic point on the lower part of the engine nacelle on the higher wing.dz is the height from the ground to the characteristic point.
(b) Calculate the arc movement.∆Y = (L - L’) - √((L - L’)2 + tan2 α × (L’2 - L2))Where:∆Y is the arc movement.L is the distance from the wing ground contact point to the fixed pivot point (forexample: main landing gear).L’ is the distance from the wing ground contact point to the leveling/lifting point.
06-10-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_A
R_0
6100
0_1_
0030
101_
01_0
0
LIF
TIN
G P
OIN
T
FU
SE
LAG
E/G
RO
UN
DC
ON
TA
CT
PO
INT
FIX
ED
PIV
OT
PO
INT
MA
IN L
AN
DIN
G G
EA
R
CH
AR
AC
TE
RIS
TIC
PO
INT
ON
FU
SE
LAG
E F
OR
AN
GLE
CA
LCU
LAT
ION
X
dzH
dx
L
L’
Arc Movement CalculationFuselage Leveling/Lifting PointFIGURE-06-10-00-991-003-A01
06-10-00Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
LIF
TIN
G P
OIN
TF
IXE
D P
IVO
T P
OIN
TM
AIN
LA
ND
ING
GE
AR
INB
OA
RD
NA
CE
LLE
/GR
OU
ND
CO
NT
AC
T P
OIN
T
CH
AR
AC
TE
RIS
TIC
PO
INT
ON
OP
PO
SIT
E W
ING
INB
OA
RD
NA
CE
LLE
FO
R A
NG
LE C
ALC
ULA
TIO
NdzY
L’
N_A
R_0
6100
0_1_
0040
101_
01_0
0
dy
L
Arc Movement CalculationWing Leveling/Lifting Point
FIGURE-06-10-00-991-004-A01
06-10-00Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
06-30-00 USE OF JACKS
**ON A/C A318-100
DESC 06-30-00-001-A01
General
1. Location of Primary Jacking Points
CAUTION : YOU CAN USE ALL COMBINATIONS OF THE JACKING POINTS (ONE ORMORE) TO LEVEL/LIFT THE AIRCRAFT. THE JACK LOADS AT EACH JACKINGPOINT MUST NOT BE MORE THAN THE ALLOWABLE LOADS (VERTICAL (FZ)AND HORIZONTAL (FH).
CAUTION : WHEN YOU LEVEL/LIFT THE AIRCRAFT, YOU MUST CONTINUOUSLYMONITOR AND RECORD THE LOADS AND MAKE SURE THAT THE LOADSYOU APPLY ARE NOT MORE THAN THE MAXIMUM ALLOWABLE LOADS. IFTHE LOADS ARE MORE THAN THE ALLOWABLE LOADS, THIS CAN CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
CAUTION : DO NOT USE THE SAME FITTING FOR TETHERING AND LIFTING OF THEAIRCRAFT AT THE SAME TIME. THE LOADS ON THE FITTING WILL CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
There are three primary jacking points on the aircraft (See FIGURE 06-30-00-991-006-A):- One under the left wing, at RIB 9- One under the right wing, at RIB 9- One on the lower forward fuselage, in front of the nose landing gear doors, at FR 8.
2. Location of Auxiliary Jacking PointsAn auxiliary jacking point for a safety stay is located on the lower aft fuselage, between FR 73 andFR 74. (See FIGURE 06-30-00-991-006-A)A jack must be installed in this position only once the aircraft is level. This point must be used tomake the aircraft stable only.
3. Maximum Jacking WeightThe maximum aircraft weight for jacking is 53000 kg (116844.97 lb).
4. Maximum LoadsSee 06-10-00 to determine the loads related to the aircraft attitude, to select the leveling/liftingprocedure.See FIGURE 06-30-00-991-010-A to determine loads on jacking pointsFz is the load applied in the vertical direction.Fh is the load applied in all horizontal directions. See TASK 06-10-00-970-802-A01 to calculate theside loads.
06-30-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Airbus recommends that you use load cells and lifting devices with side load measuring equipmentthat can accurately record and report the jacking point side loads.
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
RH Wing 28500 64070 9405 21143
LH Wing 28500 64070 9405 21143
Nose 6800 15287 2244 5045
Allowable Loads on Primary Jacking Points
TABLE 1
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
Safety Stay 2000 4496 660 1484
Allowable Loads on the Safety Stay
TABLE 2
5. Permissible wind speedSee FIGURE 06-30-00-991-010-A to determine permissible wind speed.
06-30-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
FW
D J
AC
KIN
GP
OIN
T
SA
FE
TY
PO
INT
26.4
4 m
15.1
8 m
2.74
m(8
.99
ft)
6.5
m
C L
(49.
8 ft)
(86.
75 ft
)
WIN
G J
AC
KIN
GP
OIN
T
(21.
33 ft
)
N_A
R_0
6300
0_1_
0060
101_
01_0
0
WIN
G J
AC
KIN
GP
OIN
T
Jacking PointsLocation
FIGURE-06-30-00-991-006-A01
06-30-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
70
LOA
D O
N W
ING
JA
CK
ING
PO
INT
S (
kg x
100
0)
60
50
40
30
200 3 4 5 6 7 8 9 10
NR
W (
kg x
100
0)
15
2530
3540
55
NRWA
B
D
C
21
10 20 30 4015 25 35
PERMISSIBLE WIND SPEED (Kt)
LOAD ON FORWARD FUSELAGE JACKING POINT (kg x 1000)
EXAMPLE : THE REACTION AT THE WING JACKING POINTS IS 35300 kg (17650 kg PER SIDE) AND THEREACTION AT THE FORWARD FUSELAGE JACKING POINT IS 4700 kg . IF THE AIRCRAFTMUST BE LIFTED OUTSIDE THE WIND SPEED MUST NOT BE IN EXCESS OF 29 Kt.
ASSUME AIRCRAFT WITH NRW OF 40000 kg AND CENTER OF GRAVITY AT 20% RC .A BC
D
20
30
35
45
50
55
60
65
70
40
AIRCRAFT CG (% RC)
TIP UPSECURITYMARGIN
5045
N_AR_063000_1_0100101_01_00
CG
Aircraft StabilityAircraft on Jacks
FIGURE-06-30-00-991-010-A01
06-30-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
DESC 06-30-00-001-B01
General
1. Location of Primary Jacking Points
CAUTION : YOU CAN USE ALL COMBINATIONS OF THE JACKING POINTS (ONE ORMORE) TO LEVEL/LIFT THE AIRCRAFT. THE JACK LOADS AT EACH JACKINGPOINT MUST NOT BE MORE THAN THE ALLOWABLE LOADS (VERTICAL (FZ)AND HORIZONTAL (FH).
CAUTION : WHEN YOU LEVEL/LIFT THE AIRCRAFT, YOU MUST CONTINUOUSLYMONITOR AND RECORD THE LOADS AND MAKE SURE THAT THE LOADSYOU APPLY ARE NOT MORE THAN THE MAXIMUM ALLOWABLE LOADS. IFTHE LOADS ARE MORE THAN THE ALLOWABLE LOADS, THIS CAN CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
CAUTION : DO NOT USE THE SAME FITTING FOR TETHERING AND LIFTING OF THEAIRCRAFT AT THE SAME TIME. THE LOADS ON THE FITTING WILL CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
There are three primary jacking points on the aircraft (See FIGURE 06-30-00-991-007-A):- One under the left wing, at RIB 9- One under the right wing, at RIB 9- One on the lower forward fuselage, in front of the nose landing gear doors, at FR 8.
2. Location of Auxiliary Jacking PointsAn auxiliary jacking point for a safety stay is located on the lower aft fuselage, between FR 73 andFR 74. (See FIGURE 06-30-00-991-007-A)A jack must be installed in this position only once the aircraft is level. This point must be used tomake the aircraft stable only.
3. Maximum Jacking WeightThe maximum aircraft weight for jacking is 57000 kg (125663.45 lb).
4. Maximum LoadsSee 06-10-00 to determine the loads related to the aircraft attitude, to select the leveling/liftingprocedure.See FIGURE 06-30-00-991-011-Ato determine loads on jacking points.Fz is the load applied in the vertical direction.Fh is the load applied in all horizontal directions. See TASK 06-10-00-970-802-A01 to calculate theside loads.
06-30-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Airbus recommends that you use load cells and lifting devices with side load measuring equipmentthat can accurately record and report the jacking point side loads.
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
RH Wing 28500 64070 9405 21143
LH Wing 28500 64070 9405 21143
Nose 6800 15287 2244 5045
Allowable Loads on Primary Jacking Points
TABLE 1
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
Safety Stay 2000 4496 660 1484
Allowable Loads on the Safety Stay
TABLE 2
5. Permissible Wind SpeedSee FIGURE 06-30-00-991-011-Ato determine permissible wind speed.
06-30-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
28.8
3 m
(94.
59 ft
)
2.74
m(8
.99
ft)
15.9
7 m
(52.
4 ft)
6.5
m(2
1.33
ft)
N_A
R_0
6300
0_1_
0070
101_
01_0
0
WIN
G J
AC
KIN
G
FW
D J
AC
KIN
GP
OIN
TS
AF
ET
YP
OIN
T
WIN
G J
AC
KIN
G
C L
PO
INT
PO
INT
Jacking PointsLocation
FIGURE-06-30-00-991-007-A01
06-30-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
EXAMPLE : THE REACTION AT THE WING JACKING POINTS IS 38000 kg (19000 kg PER SIDE) AND THEREACTION AT THE FORWARD FUSELAGE JACKING POINT IS 4000 kg . IF THE AIRCRAFTMUST BE LIFTED OUTSIDE THE WIND SPEED MUST NOT BE IN EXCESS OF 30 Kt.
ASSUME AIRCRAFT WITH NRW OF 42000 kg AND CENTER OF GRAVITY AT 25% RC .A BC
D
70
LOA
D O
N W
ING
JA
CK
ING
PO
INT
S (
kg x
100
0)
60
50
40
30
200 4 5 6 7 8 9 10
30
35
45
50
55
60
65
70
40
NR
W (
kg x
100
0)
15
3035
40
55
NRWA
B
D
C
10 20 30 4015 25 35
PERMISSIBLE WIND SPEED (Kt)
LOAD ON FORWARD FUSELAGE JACKING POINT (kg x 1000)
20
10
1 2 3
25
AIRCRAFT CG (% RC)50
TIP UPSECURITYMARGIN
45
N_AR_063000_1_0110101_01_00
CG
Aircraft StabilityAircraft on Jacks
FIGURE-06-30-00-991-011-A01
06-30-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
DESC 06-30-00-001-C01
General
1. Location of Primary Jacking Points
CAUTION : YOU CAN USE ALL COMBINATIONS OF THE JACKING POINTS (ONE ORMORE) TO LEVEL/LIFT THE AIRCRAFT. THE JACK LOADS AT EACH JACKINGPOINT MUST NOT BE MORE THAN THE ALLOWABLE LOADS (VERTICAL (FZ)AND HORIZONTAL (FH).
CAUTION : WHEN YOU LEVEL/LIFT THE AIRCRAFT, YOU MUST CONTINUOUSLYMONITOR AND RECORD THE LOADS AND MAKE SURE THAT THE LOADSYOU APPLY ARE NOT MORE THAN THE MAXIMUM ALLOWABLE LOADS. IFTHE LOADS ARE MORE THAN THE ALLOWABLE LOADS, THIS CAN CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
CAUTION : DO NOT USE THE SAME FITTING FOR TETHERING AND LIFTING OF THEAIRCRAFT AT THE SAME TIME. THE LOADS ON THE FITTING WILL CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
There are three primary jacking points on the aircraft (See FIGURE 06-30-00-991-008-A):- One under the left wing, at RIB 9- One under the right wing, at RIB 9- One on the lower forward fuselage, in front of the nose landing gear doors, at FR 8.
2. Location of Auxiliary Jacking PointsAn auxiliary jacking point for a safety stay is located on the lower aft fuselage, between FR 73 andFR 74. (See FIGURE 06-30-00-991-008-A)A jack must be installed in this position only once the aircraft is level. This point must be used tomake the aircraft stable only.
3. The maximum aircraft weight for jacking is 59000 kg (130072.70 lb).
4. Maximum LoadsSee 06-10-00 to determine the loads related to the aircraft attitude, to select the leveling/liftingprocedure.See FIGURE 06-30-00-991-012-A to determine loads on jacking points.Fz is the load applied in the vertical direction.Fh is the load applied in all horizontal directions. See TASK 06-10-00-970-802-A01 to calculate theside loads.Airbus recommends that you use load cells and lifting devices with side load measuring equipmentthat can accurately record and report the jacking point side loads.
06-30-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
RH Wing 28500 64070 9405 21143
LH Wing 28500 64070 9405 21143
Nose 6800 15287 2244 5045
Allowable Loads on Primary Jacking Points
TABLE 1
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
Safety Stay 2000 4496 660 1484
Allowable Loads on the Safety Stay
TABLE 2
5. Permissible Wind SpeedSee FIGURE 06-30-00-991-012-A to determine permissible wind speed.
06-30-00Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
2.74
m(8
.99
ft)
FW
D J
AC
KIN
GP
OIN
T
C L
WIN
G J
AC
KIN
GP
OIN
T
6.5
m(2
1.33
ft)
SA
FE
TY
PO
INT
WIN
G J
AC
KIN
GP
OIN
T
N_A
R_0
6300
0_1_
0080
101_
01_0
0
17.5
6 m
(57.
61 ft
)
32.5
7 m
(106
.86
ft)
Jacking PointsLocation
FIGURE-06-30-00-991-008-A01
06-30-00Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
EXAMPLE : THE REACTION AT THE WING JACKING POINTS IS 34700 kg (17350 kg PER SIDE) AND THEREACTION AT THE FORWARD FUSELAGE JACKING POINT IS 3300 kg . IF THE AIRCRAFTMUST BE LIFTED OUTSIDE THE WIND SPEED MUST NOT BE IN EXCESS OF 30 Kt.
ASSUME AIRCRAFT WITH NRW OF 38000 kg AND CENTER OF GRAVITY AT 24% RC .A BC
D
NR
W (
kg x
100
0)
AIRCRAFT CG (% RC)
A
B
0 4 5 6 7 8 9 10D
10 20 30 4015 25 35
PERMISSIBLE WIND SPEED (Kt)
LOAD ON FORWARD FUSELAGE JACKING POINT (kg x 1000)
3
70
LOA
D O
N W
ING
JA
CK
ING
PO
INT
S (
kg x
100
0)
60
50
40
30
20
C
15
3035
5550
45
2010
25
40
TIP UPSECURITYMARGIN
30
35
45
50
55
60
65
70
40
1 2
N_AR_063000_1_0120101_01_00
CG
NRW
Aircraft StabilityAircraft on Jacks
FIGURE-06-30-00-991-012-A01
06-30-00Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
DESC 06-30-00-001-D01
General
1. Location of Primary Jacking Points
CAUTION : YOU CAN USE ALL COMBINATIONS OF THE JACKING POINTS (ONE ORMORE) TO LEVEL/LIFT THE AIRCRAFT. THE JACK LOADS AT EACH JACKINGPOINT MUST NOT BE MORE THAN THE ALLOWABLE LOADS (VERTICAL (FZ)AND HORIZONTAL (FH).
CAUTION : WHEN YOU LEVEL/LIFT THE AIRCRAFT, YOU MUST CONTINUOUSLYMONITOR AND RECORD THE LOADS AND MAKE SURE THAT THE LOADSYOU APPLY ARE NOT MORE THAN THE MAXIMUM ALLOWABLE LOADS. IFTHE LOADS ARE MORE THAN THE ALLOWABLE LOADS, THIS CAN CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
CAUTION : DO NOT USE THE SAME FITTING FOR TETHERING AND LIFTING OF THEAIRCRAFT AT THE SAME TIME. THE LOADS ON THE FITTING WILL CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
There are three primary jacking points on the aircraft (See FIGURE 06-30-00-991-009-A):- One under the left wing, at RIB 9- One under the right wing, at RIB 9- One on the lower forward fuselage, in front of the nose landing gear doors, at FR 8.
2. Location of Auxiliary Jacking PointsAn auxiliary jacking point for a safety stay is located on the lower aft fuselage, between FR 73 andFR 74. (See FIGURE 06-30-00-991-009-A)A jack must be installed in this position only once the aircraft is level. This point must be used tomake the aircraft stable only.
3. Maximum Jacking WeightThe maximum aircraft weight for jacking is 69000 kg (152118.92 lb).
4. Maximum LoadsSee 06-10-00 to determine the loads related to the aircraft attitude, to select the leveling/liftingprocedure.See FIGURE 06-30-00-991-013-A to determine load on jacking points.Fz is the load applied in the vertical direction.Fh is the load applied in all horizontal directions. See TASK 06-10-00-970-802-A01 to calculate theside loads.
06-30-00Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Airbus recommends that you use load cells and lifting devices with side load measuring equipmentthat can accurately record and report the jacking point side loads.
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
RH Wing 33400 75086 11022 24778
LH Wing 33400 75086 11022 24778
Nose 6800 15287 2244 5045
Allowable Loads on Primary Jacking Points
TABLE 1
Jacking Point Fz (daN) Fz (lbf) Fh (daN) Fh (lbf)
Safety Stay 2000 4496.18 660 1484
Allowable Loads on the Safety Stay
TABLE 2
5. Permissible Wind speedSee FIGURE 06-30-00-991-013-A to determine permissible wind speed.
06-30-00Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_A
R_0
6300
0_1_
0090
101_
01_0
0
2.74
m(8
.99
ft)
FW
D J
AC
KIN
GP
OIN
T
C L
21.8
3 m
(71.
62 ft
)
WIN
G J
AC
KIN
GP
OIN
T
6.5
m(2
1.33
ft)
WIN
G J
AC
KIN
GP
OIN
T
SA
FE
TY
PO
INT
39.5
m
(129
.56
ft)
Jacking PointsLocation
FIGURE-06-30-00-991-009-A01
06-30-00Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
EXAMPLE : THE REACTION AT THE WING JACKING POINTS IS 58000 kg (29000 kg PER SIDE) AND THEREACTION AT THE FORWARD FUSELAGE JACKING POINT IS 4500 kg . IF THE AIRCRAFTMUST BE LIFTED OUTSIDE THE WIND SPEED MUST NOT BE IN EXCESS OF 38 Kt.
ASSUME AIRCRAFT WITH NRW OF 62500 kg AND CENTER OF GRAVITY AT 22% RC .A BC
D
NR
W (
kg x
100
0)
A
B
0 4 5 6 7 8 9 10D
20 30
55
10 25 35
PERMISSIBLE WIND SPEED (Kt)
LOAD ON FORWARD FUSELAGE JACKING POINT (kg x 1000)
3
70
LOA
D O
N W
ING
JA
CK
ING
PO
INT
S (
kg x
100
0)
60
50
40
30
20
C
15
303580
2025
40
4045
10
30
35
45
50
55
60
40
65
75
70
80
1
AIRCRAFT CG (% RC)
TIP UPSECURITYMARGIN
4550
2
N_AR_063000_1_0130101_01_00
NRW
CG
Aircraft StabilityAircraft on Jacks
FIGURE-06-30-00-991-013-A01
06-30-00Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 06-30-00-002-A01
Type of Jacks
1. There are three general types of jacks:
A. Special Aircraft Recovery JacksThis type of jack can move along the arc movement in the specified limits.The jack manufacturer instructions must be obeyed.There are two primary types of aircraft recovery jacks: hydraulic and low profile multi-stagejacks:- Monopole design:
This is a multi stage single ram attached to a large base plate. The jacking head can movealong the arc movement in the specified limits.
- Tripod design:This type of jack is almost the same as a hanger or maintenance tripod jack. The differenceis that it is possible to operate and control each multi-stage leg independently. Pressuregauges are installed on each leg to monitor loads independently. The operator can makesure the jack head moves in a limited arc. It is possible to operate the jack manually with alever or control it from a powered console.
B. Standard Maintenance Tripod JacksThis type of jack is can only do a very limited arc movement. We recommend you do not use astandard maintenance jack for recovery operations. When you use a standard maintenance jack,it is necessary to do the lifting operation in small steps and reposition the jack between eachstep.
C. Bottle or Wheel JacksThey can be used for initial leveling or lifting in constricted areas. They have the same limit asthe standard maintenance tripod jacks.
06-30-00Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-30-00-581-802-A01
Jacking
1. GeneralThis section gives the data related to the aircraft jacking for leveling or lifting.
NOTE : If you use jacks to level or lift the aircraft, you must put them in position on a satisfactorybase. The surface must be flat and the jack must be plumb in place.
2. InspectionsDo an inspection of the area of each jacking point that you will use. Make sure there is no damageand that each jacking point is serviceable.
3. Job Setup ReferencesFor jacking point locations, see DESC 06-30-00-001-A01DESC 06-30-00-001-B01DESC 06-30-00-001-C01DESC 06-30-00-001-D01.For general data on jack adaptors, see FIGURE 06-30-00-991-004-A.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATION98D07103500000 JACK ADAPTER - FUSELAGE98D104000001 JACKING PAD SET (A318, A319, A320)
98D07104081000 JACKING PAD SET (A321)
98D07103000000 DYNAMOMETER - SAFETY STAY
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONDESC 06-30-00-001-A01 DESC 06-30-00-001-A01-GeneralDESC 06-30-00-001-B01 DESC 06-30-00-001-B01-GeneralDESC 06-30-00-001-C01 DESC 06-30-00-001-C01-GeneralDESC 06-30-00-001-D01 DESC 06-30-00-001-D01-GeneralFIGURE 06-30-00-991-004-A FIGURE 06-30-00-991-004-A-Installation of the Jack Adaptors
Referenced Information
TABLE 2
06-30-00Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURING THERECOVERY PROCESS.
CAUTION : YOU CAN USE ALL COMBINATIONS OF THE JACKING POINTS (ONE ORMORE) TO LEVEL/LIFT THE AIRCRAFT. THE JACK LOADS AT EACH JACKINGPOINT MUST NOT BE MORE THAN THE ALLOWABLE LOADS (VERTICAL (FZ)AND HORIZONTAL (FH).
CAUTION : YOU MUST NOT USE THE SAFETY STAY TO LEVEL OR LIFT THE AIRCRAFT.
CAUTION : BEFORE YOU LIFT OR YOU LOWER THE AIRCRAFT MAKE SURE THATTHERE IS NO EQUIPMENT ADJACENT TO IT THAT CAN CAUSE DAMAGE.MAKE SURE THAT NO OTHER WORK IS BEING DONE.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
Subtask 06-30-00-581-003-A01
A. Installation of the jack adaptors
(1) At the FWD jacking point, FR8:See FIGURE 06-30-00-991-004-A.
(a) Examine the 98D07103500000 JACK ADAPTER - FUSELAGE (1) and make surethat there is no damage.
(b) Install the 98D07103500000 JACK ADAPTER - FUSELAGE (1) at the FWD jackingpoint.
(2) At the wing Jacking Points, RIB9:See FIGURE 06-30-00-991-004-A.
(a) Remove the blanking plugs from the wing.
(b) Install the dowels (3)
(c) Put the 98D104000001 JACKING PAD SET (A318, A319, A320) or98D07104081000 JACKING PAD SET (A321) (2) in position under the wing andinstall the bolt.
(3) At the Auxiliary Jacking Point, between FR73 and FR74:See FIGURE 06-30-00-991-004-A
(a) Install the 98D07103000000 DYNAMOMETER - SAFETY STAY (4) at the safetystay point.
06-30-00Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
LOWER SURFACE
AB
BC
01
02
03
NOTE:
FOR DETAILS, SEE SHEET 2
FOR DETAILS, SEE SHEET 3
FOR DETAILS, SEE SHEET 4
02
FR8
FR73FR74
2
3
1
A C01 03
B
N_AR_063000_1_0040101_01_00
RIB9
RIB9
Installation of the Jack AdaptorsGeneral (Sheet 1 of 4)
FIGURE-06-30-00-991-004-A01
06-30-00Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_063000_1_0040102_01_00
ADAPTATOR PART98A07003907200
JACK
LOAD CELL
ADAPTATOR PART98A07003906200
R 19.0 mm (0.75 in)FITTING PART98D07103500000
FR8
343A100KN2
Installation of the Jack AdaptorsForward Jacking Point (Sheet 2 of 4)
FIGURE-06-30-00-991-004-A01
06-30-00Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_063000_1_0040103_01_00
ADAPTOR
ADAPTOR
LOAD CELL343A400KN2
JACK
R 32 mm (1.26 in)
98A07003911200
98A07003907200
JACK PAD98D07104000001 (FOR A318, A319, A320)98D07104081000 (FOR A321)
Installation of the Jack AdaptorsWing jacking Point (Sheet 3 of 4)FIGURE-06-30-00-991-004-A01
06-30-00Page 22
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_063000_1_0040104_01_00
SAFETY JACK
ADAPTATOR
LOAD CELL
98D07103000000
19D53571595R 19 mm (0.75 in)
Installation of the Jack AdaptorsAuxiliary Jacking Point - Safety Stay (Sheet 4 of 4)
FIGURE-06-30-00-991-004-A01
06-30-00Page 23
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-30-00-581-801-A01
General Preparation and Instructions for Leveling and Lifting the Aircraft with Jacks
1. GeneralThis section gives the data related to the use of jacks to level and lift the aircraft: allowable loads,general preparation and instructions.
NOTE : If you use jacks to level or lift the aircraft, you must put them in position on a satisfactorybase. The surface must be flat and the jack must be plumb in place.
2. InspectionsNot Applicable.
3. Job Setup References
A. GeneralSee DESC 06-30-00-001-A01DESC 06-30-00-001-B01DESC 06-30-00-001-C01DESC06-30-00-001-D01 for the localization of the jacking points and allowable jacking loads.See TASK 06-30-00-581-802-A01 for data about the installation of a jack adaptor.When you lift the aircraft with three jacks, the weight of the aircraft must not be more than themaximum jacking weight. The maximum jacking weight is not applicable for leveling with oneor two jacks but the load on each jack must not be more than the maximum allowable loads.When you lift the aircraft with jacks, it is necessary to monitor the loads at the related jackingpoints.You must also make sure that the wind speed is not more than the maximum allowable speed.See DESC 06-30-00-001-A01DESC 06-30-00-001-B01DESC 06-30-00-001-C01DESC06-30-00-001-D01
B. Aircraft Jacking StabilityWhen you use jacks to level or lift the aircraft, you must put them in position on a satisfactorybase. The surface must be flat and the jack must be plumb when it is in position. The loadbearing capacity of the soil must support the loads applied at the jack footprint.You can use plywood sheets with steel plates on top to make the ground more rigid. In someconditions, it can be necessary to excavate and prepare a base of coarse gravel before you placethe plywood sheets and steel plates.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 06-30-00-581-802-A01 TASK 06-30-00-581-802-A01-Jacking
TASK 06-10-00-970-801-A01 TASK 06-10-00-970-801-A01-Vertical Loads DeterminationTASK 06-10-00-970-803-A01 TASK 06-10-00-970-803-A01-Arc Movement CalculationTASK 06-10-00-970-802-A01 TASK 06-10-00-970-802-A01-Side loads on Jack Fittings
Determination
06-30-00Page 24
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
REFERENCE DESIGNATIONTASK 02-20-02-285-801-A01 TASK 02-20-02-285-801-A01-Initial Site Survey
TASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Deviceson Landing Gears
DESC 06-30-00-001-A01 DESC 06-30-00-001-A01-GeneralDESC 06-30-00-001-B01 DESC 06-30-00-001-B01-GeneralDESC 06-30-00-001-C01 DESC 06-30-00-001-C01-GeneralDESC 06-30-00-001-D01 DESC 06-30-00-001-D01-General04-30-00 04-30-00-TETHERING THE AIRCRAFT03-50-01 03-50-01-MANAGING AIRCRAFT WEIGHT AND CG05-50-01 05-50-01-CARGO REMOVAL05-60-00 05-60-00-REMOVAL OF LARGE COMPONENTS07-60-00 07-60-00-MOVING DAMAGED AIRCRAFTAMM 07-11-00-581-001
Referenced Information
TABLE 1
5. Procedure
WARNING : OBEY THESE PRECAUTIONS WHEN YOU DO LEVELING/LIFTING OF THEAIRCRAFT. MAKE SURE THAT THE LIFTING EQUIPMENT IS APPLICABLE FORTHE SPECIFIC CONDITIONS. MAKE SURE THAT THE PERSONS WHO OPERATETHE LIFTING EQUIPMENT ARE CORRECTLY TRAINED AND HAVE A GOODKNWOLEDGE OF THE SYSTEM. MAKE SURE THAT THE NECESSARY SAFETYAREA IS KNOWN AND THAT PERSONS DO NOT GO IN THIS AREA DURINGTHE LEVELING/LIFTING OPERATIONS. LEVELING/LIFTING OF THE AIRCRAFTCAN BE DANGEROUS IF YOU DO NOT OBEY THESE PRECAUTIONS.
CAUTION : MAKE SURE THAT THE LOADS APPLIED AT EACH JACKING POINT ARE NOTMORE THAN THE MAXIMUM ALLOWABLE LOADS.
CAUTION : WHEN YOU LEVEL/LIFT THE AIRCRAFT, YOU MUST CONTINUOUSLYMONITOR AND RECORD THE LOADS AND MAKE SURE THAT THE LOADSYOU APPLY ARE NOT MORE THAN THE MAXIMUM ALLOWABLE LOADS. IFTHE LOADS ARE MORE THAN THE ALLOWABLE LOADS, THIS CAN CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
CAUTION : IF THE LOADS APPLIED DURING THE RECOVERY PROCEDURE ARE MORETHAN THE MAXIMUM ALLOWABLE LOADS, YOU MUST CONTACT AIRBUSFOR SPECIFIC INSPECTIONS.
06-30-00Page 25
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CAUTION : YOU CAN USE ALL COMBINATIONS OF THE JACKING POINTS (ONE ORMORE) TO LEVEL/LIFT THE AIRCRAFT. THE JACK LOADS AT EACH JACKINGPOINT MUST NOT BE MORE THAN THE ALLOWABLE LOADS (VERTICAL (FZ)AND HORIZONTAL (FH).
CAUTION : YOU MUST CORRECTLY TETHER THE AIRCRAFT BEFORE YOU LEVEL ORLIFT IT.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
NOTE : It is the responsibility of the recovery manager to make the decision about the applicablemethod and related equipment/personnel for the leveling/lifting of the aircraft.
Subtask 06-30-00-581-002-A01
A. General
NOTE : Before you start to level or lift the aircraft with jacks, you must make sure that thepersonnel know the instructions and conditions below and that they obey theseinstructions and conditions.
(1) Do not level or lift the aircraft with jack(s) in gusty wind conditions.
(2) Do not lift the aircraft with jacks during steady wind conditions.
(3) Find the maximum allowable wind speed related to your aircraft configuration. See DESC06-30-00-001-A01DESC 06-30-00-001-B01DESC 06-30-00-001-C01DESC 06-30-00-001-D01.
(4) Correctly tether the aircraft before leveling or lifting with jacks. This is to prevent aircraftmovement that you cannot control during the leveling or lifting operation. See 04-30-00.
(5) Read the manufacturer instructions related to the special jack(s) used.
(6) Only the personnel who knows the operation of jacks and aircraft jacking procedures are incharge of the jacking operation.
(7) Confirm the NRW and CG position. See 03-50-01.
(8) Calculate the anticipated vertical load on each jacking point to be used to make sure thisload is not more than the maximum allowable load. (See TASK 06-10-00-970-801-A01 andDESC 06-30-00-001-A01DESC 06-30-00-001-B01DESC 06-30-00-001-C01DESC06-30-00-001-D01)If the necessary load on the jacking point is more than the allowable load for that jackingpoint, reduce the aircraft weight until the lifting load is less than the allowable load ormake a selection of different leveling or lifting procedure.
06-30-00Page 26
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(9) Make sure each available jack can support the necessary load (vertical and side), arcmovement and travel range. Also make sure it can be put in the boundaries of the fuselageor wing jacking points.To reduce the necessary lifting load, it is recommended to reduce the aircraft weight withthe removal of cargo or payload from the aircraft before a leveling or lifting operation (See05-50-01 and 05-60-00).
(10) Calculate the expected arc movement at each jacking point during the leveling operation.(See TASK 06-10-00-970-803-A01)Calculate the side load if necessary. (See TASK 06-10-00-970-802-A01)
(11) If the jack cannot move along the necessary arc movement, you must calculate theexpected side load on the jacking point and make sure the expected side load is not morethan the allowable load on the jacking point.
(12) Install fittings and/or jack pad adapters at the necessary jacking points. See TASK06-30-00-581-802-A01.
(13) If necessary, excavate a sufficiently large area to make a stable platform as a base for eachjack. Make sure that the ground/soil can support the load at each jack footprint, and thatwill stay stable during the leveling or lifting operation. See TASK 02-20-02-285-801-A01)Make a platform that is satisfactory for the jack height when in compressed position. Makesure that the platform is sufficiently large to change the position of the jack during theleveling operation if necessary. If the jack in the extended position cannot lift the aircraftsufficiently, it is necessary to make a timber platform that is sufficiently high.
(14) Put wheel chocks in front of and behind the wheels of each extended landing gear incontact with the ground.
(15) Install the landing gear downlock pins in all extended landing gears. See TASK02-30-01-481-801-A01.
(16) Put each jack in position below the jacking point and extend the jack to engage it in thefitting.
(17) Before you start the jacking operation, we recommend that you mark the values of thenecessary lifting load to be applied on the jack on each load cell indicator (use a strip ofcolored adhesive tape for example).Also, we recommend that you mark the maximum allowable load of each jacking point toprevent overload. This gives the recovery personnel better visibility from the ground.
(18) Each jack operator must have a good visibility to the person in charge of the liftingoperation.Coordination between all jack operators is very important. Two-way voice activatedheadsets are very good for this type of operation.
(19) You must use and monitor plumb bobs and levels during a leveling or lifting operation.
(20) Monitor the CG during the full leveling procedure and be prepared to control with ballast ifnecessary. See 03-50-01.
06-30-00Page 27
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(21) If you use tethers, they must be adjusted and the loads must be monitored when you levelor lift the aircraft.
(22) Install aft tipping protection if necessary.
(23) When you use a jack at the safety stay position to make the aircraft stable, you mustmonitor the jack and correctly adjust the loads.
(24) Make sure the loads at each jack are not more than the allowable loads and that yourecord all the loads applied. See DESC 06-30-00-001-A01DESC 06-30-00-001-B01DESC06-30-00-001-C01DESC 06-30-00-001-D01.
(25) Level the aircraft:
(a) With a special recovery jack:If you use a special recovery jack that can move along the arc movement, make surethe jack can do the necessary arc movement to level the aircraft. Include side loadscaused by the jack.If the jack cannot do the total necessary arc movement, gradually level the aircraft insmall steps and change the position of the jack between each step.
(b) With a standard jack:If the jack cannot sufficiently move along the arc movement or if you use a standardjack, gradually level the aircraft in small steps and change the position of the jackbetween each step.- Start jacking until you get the maximum jack extension or maximum arc
movement.- Lock the jack at this position and make sure the aircraft is in a stable
configuration.- At the same time, make shoring under the closest load bearing frame or frames
and make sure the loads are not more the maximum allowable loads.- Compress the jack, make the necessary stable-base platform and change the
position of the jack. Do the procedure again until the aircraft is level.
NOTE : If possible, you should use a special recovery jack. Step by step leveling isnot the recommended method to level the aircraft.
(26) It is possible to use axle jacks with shoring and timber bases at the primary jacking pointsto lift the aircraft to the height where recovery jacks can be fitted. This is not arecommended procedure because of the limited arc movement capacity of the jack.
(27) When the fuselage and wings are level, and if it is necessary to lift the aircraft, use the 3primary jacking points to lift the aircraft to the necessary height. (See AMM07-11-00-581-001)Do not lift the aircraft until all the aircraft (wings and fuselage) is in a level attitude.
(28) When the aircraft is at the necessary height:
(a) Make shoring to support the fuselage and/or wings, or leave the jacks in place as asafety measure during work on the landing gears.
06-30-00Page 28
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(b) Extend the landing gear(s) and install the downlock pin(s).
(c) Or repair or replace the landing gear(s).
(d) Or, if it is not possible to make the landing gear(s) serviceable, place the forwardfuselage and/or the wing(s) on a mobile device. See 07-60-00.
06-30-00Page 29
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
06-40-00 USE OF PNEUMATIC LIFTING BAGS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 06-40-00-002-A01
General
1. This section gives data about the use of pneumatic lifting bags for leveling and lifting : location ofbearing areas, allowable loads, general preparation and instructions.Pneumatic lifting bags have different sizes and lifting capacities. In general, multiple-elementpneumatic lifting bags with internal drop threads are the most usual. Single-element pneumatic liftingbags (balloon bags) are not recommended as floating loads could appear. Operator must have aspecific training to operate the equipments.You must know and obey the operating instructions given by the manufacturer of the pneumaticlifting bags.For leveling and lifting on the fuselage, see DESC 06-40-00-001-A01.For leveling and lifting on wings, see DESC 06-40-00-003-A01.For general information and instruction related to the use of pneumatic lifting bags, see TASK06-40-00-581-801-A01.
06-40-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 06-40-00-001-A01
Pneumatic Lifting Bags on Fuselage
1. For the leveling and lifting of the fuselage with pneumatic lifting bags, contact AIRBUS.
CAUTION : MAKE SURE THAT THE PNEUMATIC LIFTING BAGS APPLY LOADS IN THEBEARING AREA ONLY. IF THE LIFTING BAGS APPLY LOADS OUT OF THELIMITS OF THE BEARING AREA, SECONDARY DAMAGE CAN OCCUR.
CAUTION : MAKE SURE THAT THE PNEUMATIC LIFTING BAGS DO NOT APPLY LOADSON THE BELLY FAIRING STRUCTURE. IF NECESSARY, REMOVE THE BELLYFAIRINGS AND THE BELLY FAIRING STRUCTURE TO GET ACCESS TO THEALLOWABLE BEARING AREA.
CAUTION : DO NOT PUT THE LIFTING BAGS UNDER PROTRUDING STRUCTURES (FLAPTRACKS,PYLON FAIRINGS, ETC.), SHARP EDGES OR ANGLES BECAUSE THEYCAN CAUSE DAMAGE TO THE LIFTING BAGS.
06-40-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 06-40-00-003-A01
Pneumatic Lifting Bags on Wings
1. Bearing Areas on Wing Lower Surface
CAUTION : MAKE SURE THAT THE PNEUMATIC LIFTING BAGS APPLY LOADS IN THEBEARING AREA ONLY. IF THE LIFTING BAGS APPLY LOADS OUT OF THELIMITS OF THE BEARING AREA, SECONDARY DAMAGE CAN OCCUR.
CAUTION : MAKE SURE THAT THE LOADS ON THE AIRFRAME ARE LESS THAN THEALLOWABLE LOADS WHEN YOU USE SUPPORTS. THE SUPPORTS APPLYLOADS THAT DO NOT OCCUR IN NORMAL OPERATION.
CAUTION : DO NOT PUT THE LIFTING BAGS UNDER PROTRUDING STRUCTURES (FLAPTRACKS,PYLON FAIRINGS, ETC.), SHARP EDGES OR ANGLES BECAUSE THEYCAN CAUSE DAMAGE TO THE LIFTING BAGS.
This part gives data about the installation of pneumatic lifting bags under the wings.
A. LocationPneumatic lifting bags can be installed under the wing lower surfaces between Rib 1 and Rib17*, see FIGURE 06-40-00-991-001-A.
B. Restricted AreasThe limits of the allowable bearing areas for the pneumatic lifting bags are shown in FIGURE06-40-00-991-003-A.
C. Allowable Loads
Maximum Allowable PressureBearing Area
PSI hPa BarRib 1 to Rib 17 7 480 0.48
Maximum Allowable Pressure
TABLE 1
D. After you use pneumatic lifting bags on wings for leveling/lifting of the aircraft, you must do aninspection of the wing tank access panels in the contact area.Report any sign of damage.
06-40-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
FRONT SPAR
RIB17
RIB1
REAR SPAR
MAKE SURE THAT THE PNEUMATIC LIFTING BAGS APPLY LOADS IN THE BEARING AREA ONLY. IF THE PNEUMATIC LIFTING BAGS APPLY LOADS OUT OF THE LIMITS OF THE BEARING AREA, SECONDARY DAMAGE CAN OCCUR.
BEARING AREA ON WING LOWER SURFACE (7PSI)
CAUTION:
N_AR_064000_1_0010101_01_00
A
AFWD
RH SYMMETRICALLH SHOWN
Pneumatic Lifting Bags on WingsBearing Area on Wing Lower Surface
FIGURE-06-40-00-991-001-A01
06-40-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CAUTION: IF THE PNEUMATIC LIFTING BAGS APPLY LOADS OUT OF THE LIMITS OF THE BEARING AREA, SECONDARY DAMAGE CAN OCCUR.
BEARING AREA ON WING LOWER SURFACE
FRONT SPAR
RIB17
RIB1REAR SPAR
RIB13
RIB12
RIB8
WING JACKING POINT
JACKING POINTRESTRICTED AREA
NOTE: THE TRIPOD FOOT. THE FOOTPRINT IS RELATED TO THE TYPE OF JACK. IT IS IMPORTANT TO KNOW THE FOOTPRINT OF THE JACK YOU WILL USE BEFORE YOU PUT THE LIFTING BAG(S) IN POSITION.
RIB6
THE JACK FOOTPRINT IS MEASURED FROM THE CENTERLINE OF THE JACK TO THE CENTERLINE OF
MAKE SURE THAT THE PNEUMATIC LIFTING BAGS APPLY LOADS IN THE BEARING AREA ONLY.
A
RH SYMMETRICAL
N_AR_064000_1_0030101_01_00
FWD ALH SHOWN
Pneumatic Lifting Bags on WingsWing Restricted Area
FIGURE-06-40-00-991-003-A01
06-40-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-40-00-581-801-A01
General Preparation and Instructions for Leveling and Lifting the Aircraft with Pneumatic Lifting Bags
1. GeneralThis section gives the data about the use of pneumatic lifting bags for leveling and lifting: allowableloads, general preparation and instructions.
NOTE : If you use pneumatic lifting bags to level or lift the aircraft they must be put in position ona stable base. The surface must be flat.
2. InspectionsNot Applicable.
3. Job Setup ReferencesPneumatic lifting bag movement is related to the attitude of the aircraft. See TBD for data aboutthe applicable scenario.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 06-10-00-970-801-A01 TASK 06-10-00-970-801-A01-Vertical Loads DeterminationTASK 06-10-00-970-803-A01 TASK 06-10-00-970-803-A01-Arc Movement CalculationTASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Devices
on Landing Gears
DESC 06-00-00-002-A01 DESC 06-00-00-002-A01-Leveling/Lifting Obstructions
04-30-00 04-30-00-TETHERING THE AIRCRAFT03-00-00 03-00-00-WEIGHT AND CG MANAGEMENT05-00-00 05-00-00-WEIGHT REDUCTION06-10-00 06-10-00-LOAD DETERMINATION04-50-00 04-50-00-SOIL STABILITY03-20-01 03-20-01-FUEL LOAD AND CG CONTROL06-30-00 06-30-00-USE OF JACKS07-60-00 07-60-00-MOVING DAMAGED AIRCRAFTAMM 07-11-00-581-001
Referenced Information
TABLE 1
06-40-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
WARNING : OBEY THESE PRECAUTIONS WHEN YOU DO LEVELING/LIFTING OF THEAIRCRAFT. MAKE SURE THAT THE LIFTING EQUIPMENT IS APPLICABLE FORTHE SPECIFIC CONDITIONS. MAKE SURE THAT THE PERSONS WHO OPERATETHE LIFTING EQUIPMENT ARE CORRECTLY TRAINED AND HAVE A GOODKNWOLEDGE OF THE SYSTEM. MAKE SURE THAT THE NECESSARY SAFETYAREA IS KNOWN AND THAT PERSONS DO NOT GO IN THIS AREA DURINGTHE LEVELING/LIFTING OPERATIONS. LEVELING/LIFTING OF THE AIRCRAFTCAN BE DANGEROUS IF YOU DO NOT OBEY THESE PRECAUTIONS.
CAUTION : MAKE SURE THAT THE LOADS ON THE AIRFRAME ARE LESS THAN THEALLOWABLE LOADS WHEN YOU USE SUPPORTS. THE SUPPORTS APPLYLOADS THAT DO NOT OCCUR IN NORMAL OPERATION.
CAUTION : THE STIFFNESS AND LATERAL STABILITY OF PNEUMATIC LIFTING BAG CANCHANGE DURING THE INFLATION PROCESS OF THE PNEUMATIC LIFTINGBAG STACK. IT IS THE RESPONSIBILITY OF THE PNEUMATIC LIFTING BAGMANUFACTURER TO PROVIDE ADEQUATE DATA ON THE USE OF ITSLIFTING BAGS.IT IS THE RESPONSIBILITY OF THE RECOVERY MANAGER TO MAKE SURETHAT USE OF THE PNEUMATIC LIFTING BAG WILL NOT LEAD TO AIRCRAFTMOVEMENT DUE TO THE INFLUENCE OF WIND AND/OR CHANGE OF CGPOSITION DURING AIRCRAFT LIFTING/LEVELING.
CAUTION : WHEN YOU LEVEL/LIFT THE AIRCRAFT, YOU MUST CONTINUOUSLYMONITOR AND RECORD THE LOADS AND MAKE SURE THAT THE LOADSYOU APPLY ARE NOT MORE THAN THE MAXIMUM ALLOWABLE LOADS. IFTHE LOADS ARE MORE THAN THE ALLOWABLE LOADS, THIS CAN CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
CAUTION : IF THE LOADS APPLIED DURING THE RECOVERY PROCEDURE ARE MORETHAN THE MAXIMUM ALLOWABLE LOADS, YOU MUST CONTACT AIRBUSFOR SPECIFIC INSPECTIONS.
CAUTION : DO NOT PUT THE LIFTING BAGS UNDER PROTRUDING STRUCTURES (FLAPTRACKS,PYLON FAIRINGS, ETC.), SHARP EDGES OR ANGLES BECAUSE THEYCAN CAUSE DAMAGE TO THE LIFTING BAGS.
CAUTION : MAKE SURE THAT THE PNEUMATIC LIFTING BAGS DO NOT APPLY LOADSON THE BELLY FAIRING STRUCTURE. IF NECESSARY, REMOVE THE BELLYFAIRINGS AND THE BELLY FAIRING STRUCTURE TO GET ACCESS TO THEALLOWABLE BEARING AREA.
06-40-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CAUTION : MAKE SURE THAT THE PNEUMATIC LIFTING BAGS APPLY LOADS IN THEBEARING AREA ONLY. IF THE LIFTING BAGS APPLY LOADS OUT OF THELIMITS OF THE BEARING AREA, SECONDARY DAMAGE CAN OCCUR.
CAUTION : YOU MUST CORRECTLY TETHER THE AIRCRAFT BEFORE YOU LEVEL ORLIFT IT.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
NOTE : It is the responsibility of the recovery manager to make the decision about the applicablemethod and related equipment/personnel for the leveling/lifting of the aircraft.
Subtask 06-40-00-581-001-A01
A. General
NOTE : Before you start to level or lift the aircraft with pneumatic lifting bags, you mustmake sure that the personnel know the instructions and conditions below and thatthey obey these instructions and conditions.
(1) Read the pneumatic lifting bag manufacturer instructions applicable to the pneumaticlifting bags that you use.
(2) Only the personnel that knows the operation of pneumatic lifting bags and aircraft jackingprocedures should be in charge of the pneumatic lifting bags operation.
(3) Do not lift the aircraft with pneumatic lifting bags in gusty wind conditions. Follow themanufacturer limitations.
(4) Do not lift the aircraft with pneumatic lifting bags during steady wind conditions. Followthe manufacturer limitations.
(5) Correctly tether the aircraft before leveling or lifting with pneumatic lifting bags. This is toprevent aircraft movement that you cannot control during the leveling or lifting operation.See 04-30-00.
(6) Confirm the aircraft NRW and CG. See 03-00-00.
(7) Calculate the anticipated vertical load on each lifting bag position to be used to make surethe necessary load is not more than the maximum allowable load on the skin. See TASK06-10-00-970-801-A01.If the necessary load on the bearing area of the pneumatic lifting bag is more than theallowable load for that leveling/lifting point, reduce the aircraft weight until the lifting loadis less than the allowable load or install additional pneumatic lifting bags to increasecontact surface to reduce applied loads or make a selection of another leveling or liftingprocedure.
06-40-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(8) Calculate the total lift of each pneumatic lifting bag used. Make sure each available liftingbag can support the necessary loads (vertical and side), arc movement and travel range,and can fit in the limits of the fuselage or wing contact zone.To reduce the necessary leveling/lifting load, we recommend that you reduce the aircraftweight with the removal of cargo and/or fuel if necessary (05-00-00) from the aircraftbefore a leveling/lifting operation, see 06-10-00.
(9) Calculate the expected arc movement during the leveling/lifting operation, at the center ofthe bearing area of each pneumatic lifting bag . Also calculate the side load if necessary,see 06-10-00.
(10) Before you use pneumatic lifting bags, do an inspection of the structure to make sure thereis no damage in the leveling/lifting area. If there is damage, the pneumatic lifting bagsmust be installed at least at one non-damaged rib/fuselage frame away from the damagedarea. Remove all sharp edges from the contact area. Use a heavy tarpaulin or foam rubbermattress between the aircraft skin and the pneumatic lifting bag to prevent damage.
(11) Put the pneumatic lifting bags in the allowable bearing areas, and make sure no sharpedges or peaks (damaged skin , protruding structure, antennas ...) are in the area wherethe bags will be installed.
(12) Remove some unwanted items (antennas, ...) from the aircraft before you install thepneumatic lifting bags, see DESC 06-00-00-002-A01.
(13) If necessary, excavate a sufficiently large area to make a stable base for the pneumaticlifting bags. Make sure that the ground/soil can support the load at each lifting bagfootprint, and will stay stable during the leveling/lifting operation, see 04-50-00. Make asatisfactory base for the height of the compressed pneumatic lifting bags. Make sure thatthe base is sufficiently large to change the position of the pneumatic lifting bags during theleveling/lifting operation if necessary. If the inflated pneumatic lifting is not sufficientlyhigh to lift the aircraft, it will be necessary to make a sufficiently high platform. It ispossible to make this platform with timber or to use an inflatable type platform.
(14) The arc movement will cause a transversal translation of the aircraft. If this movement ismore than the allowable limit of the pneumatic lifting bag (see manufacturer instructions),a leveling/lifting operation with several steps is necessary to reposition the pneumatic liftingbags. The use of a secondary method of lifting (for example jacks) is necessary.
(15) If necessary, put wheel chocks in front and behind the wheels of each landing gear that isextended and in contact with the ground.
(16) If possible, install landing gear downlock pins in all landing gears that are extended.
(17) Each operator at the pneumatic-lifting bag control console must have a good visibility ofthe leveling/lifting operation. Coordination between all the console operators is veryimportant. Two-way voice headsets are recommended for this type of operation.
(18) No personnel must be in or below the aircraft during the leveling/lifting process.
06-40-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(19) Movement of fuel in the wing tanks because of aircraft leveling/lifting can cause a changein the aircraft CG position. It is thus recommended that all fuel is removed from theaircraft before leveling/lifting, see 03-20-01. This will also reduce the necessary liftingloads.
(20) Anticipate the CG movement before you start the leveling/lifting process and be preparedto control with ballast.
(21) Monitor and record the applied loads (pressure in the pneumatic lifting bags) at all timesduring the leveling/lifting process.
(22) Before the leveling/lifting operation, make an estimate of the arc movement, see TASK06-10-00-970-803-A01.During the leveling/lifting operation, you must monitor the lateral translation of theaircraft (with the use of a plumb-line) and compare it to the calculation and the pneumaticlifting bag limitations (see manufacturer instructions) to prevent any aircraft suddenmovement or sliding.
(23) Install aft tipping protection if necessary.
(24) Before you inflate the pneumatic lifting bags, make sure that you know all the warningsand safety precautions. Make sure that all equipment (such as shoring material or jacks) isprepared and available to use.
(25) Obey the manufacturer’s instructions: inflate the lifting bags slowly and adjust the tetherswhen the aircraft starts to move.
(26) When the fuselage and wing are level, and if the aircraft needs to be lifted, it isrecommended to use the 3 jacking points to lift the aircraft to the necessary height, seeAMM 07-11-00-581-001. It is mandatory that the aircraft is in a level attitude (wing andfuselage) before you lift it.
(27) When the aircraft is at the necessary height:
(a) Use shoring to support the fuselage and/or wings, or install jacks (see 06-30-00) as asafety measure during any work on the landing gears.
(b) Extend the landing gear(s) and install downlock pin(s), see TASK 02-30-01-481-801-A01,
(c) Or repair or replace the landing gear(s),
(d) Or, if it is not possible to make the landing gear(s) serviceable, place the forwardfuselage and/or the wing(s) on a mobile device, see 07-60-00.
(28) After the recovery process, do an inspection of the skin in the contact areas of thepneumatic bag for scratches, nicks and gouges caused by sand or stones trapped betweenthe contact surfaces.You must also do an inspection of the wing tank access panels in the contact area.Report any sign of damage.
06-40-00Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
06-50-00 USE OF CRANES
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 06-50-00-001-A01
General
1. This chapter gives detail on the use of cranes for leveling or lifting the aircraft.The lifting of an aircraft with crane is a specific lifting procedure with specific tools, accurateengineering planning and risk/hazard assessment.A process management chart gives all the steps of the crane lifting, see FIGURE 06-50-00-991-020-A.See TASK 06-50-00-581-803-A01 for lifting by the forward fuselage.See TASK 06-50-00-581-802-A01 for lifting by the wings.See TASK 06-50-00-581-801-A01 for general preparation and instruction for leveling and lifting withcranes.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
06-50-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CRANE LIFTING PROCESS
RECORD WEATHERCONDITIONS
CALCULATE CG AND DECREASEWEIGHT IF NECESSARY
PLAN TOOLING INSTALLATIONAND LIFTING PROCEDURE
DO THE LIFTING ASPLANNED
PLAN PREPARATION MEETING
N_AR_065000_1_0200101_01_02
CALCULATE THE LOADSTHAT WILL BE APPLIED
STRUCTURALINTEGRITY OF MOORING
FITTINGS, ATTACHMENT CABLESYSTEMS AND CARDAN PIN
EYE END OF THE LG SIDE STAYMOUNTING BRACKET
DO A CHECK OF THE
MAKE SURE THATTHE SOIL IS STABLE
Crane LiftingProcess Management Chart
FIGURE-06-50-00-991-020-A01
06-50-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-50-00-581-803-A01
Forward Fuselage Crane Lifting
1. GeneralThis section gives the data related to the leveling and lifting from the forward fuselage with cranes.
2. InspectionsNot Applicable.
3. Job Setup ReferencesThere are two methods to lift the forward fuselage with cranes and slings:- With a spreader beam and a strap installed at FR15 or FR20, see SUBTASK 06-50-00-581-002-
A01.- With mooring fittings installed at FR15, see SUBTASK 06-50-00-581-003-A01.You can use this task in combination with the Wing Crane Lifting procedure (see TASK06-50-00-581-802-A01) or one other lifting method (jacking or use of pneumatic lifting bags).
A. Straps / slingsThe straps touch directly the aircraft fuselage skin. They must be made from soft nylon toprevent scratches and gouges.The minimum width of the straps must be 200 mm (8 in).The two ends of the straps must have adapted loops for attachment to the crane hook orspreader bar.The straps must be in good condition without broken fibers, cuts, nicks or gouges.
B. Transversal Spreader BeamIf only one crane is available, you can use a spreader beam between each end of the sling.The distance between the hook attachment points of the slings on the spreader beam must beequal to 3950 mm (155.51 in) to have a sling angle of 180˚ around the lower fuselage. SeeFIGURE 06-50-00-991-014-AIf this distance is less than 3950 mm (155.51 in), this can cause lateral loads and secondarydamage can occur on the fuselage sides.If this distance is more than 3950 mm (155.51 in), the contact surface between the fuselage andthe strap will not be sufficient and excessive loads can be applied on the lower fuselage.
C. CraneThe crane must be able to hold the maximum lifting load.It is recommended that you use a crane with at least a 11 m (433.07 in) high jib.
D. Allowable LoadsThe maximum lifting load on FR15 or Fr 20 is 6700 daN (150.62 lbf). See FIGURE06-50-00-991-021-A to find the lifting load on FR15 or FR20 related to the aircraft weight andCG position.
06-50-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATION98D07203000 MOORING FITTING
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONTASK 06-50-00-581-802-A01 TASK 06-50-00-581-802-A01-Wing Crane Lifting
TASK 06-50-00-581-801-A01 TASK 06-50-00-581-801-A01-General Preparation andinstructions for Leveling and Lifting th
06-40-00 06-40-00-USE OF PNEUMATIC LIFTING BAGSFIGURE 06-50-00-991-014-A FIGURE 06-50-00-991-014-A-FWD Fuselage Crane Lifting
FIGURE 06-50-00-991-021-A FIGURE 06-50-00-991-021-A-FWD Fuselage Crane Lifting
FIGURE 06-50-00-991-015-A FIGURE 06-50-00-991-015-A-FWD Fuselage Crane Lifting
Referenced Information
TABLE 2
5. Procedure
Subtask 06-50-00-581-002-A01
A. Strap installation at FR15 or FR20
(1) Use a strap with a minimum length of 10300 mm (405.51 in).See FIGURE 06-50-00-991-014-A for minimum dimensions of the strap and approximatelifting height.
(2) Install the strap at FR15 or FR20. The attitude of the aircraft (clearance to install strap) orthe weight and CG condition will be the basic data for the selection of the frame.
NOTE : During the lifting operation, the loads applied to FR20 will be more than the loadapplied to FR15.
(3) With one crane, the jib head must be vertically aligned with the fuselage centerline and theframe position (FR15 or FR20).With two cranes, the jib heads must be vertically aligned with each side of the fuselage andthe frame position (FR15 or FR20).
(4) Attach the slings to each crane if you use two cranes.OrAttach the spreader bar to the single crane and attache the straps to the spreader beam.
06-50-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(5) See TASK 06-50-00-581-801-A01 for the general instructions for leveling and lifting withcranes.It is recommended to install a pneumatic lifting bag (see 06-40-00) below the aft fuselageto prevent tail tipping.
(6) Lift the aircraft very slowly and avoid any dynamic effort. If other cranes or lifting methodare used simultaneously, make sure that all the operators work at the same time. The useof a two-way speaking system is recommended.
Subtask 06-50-00-581-003-A01
B. Fitting installation at FR15
(1) At FR15, remove the blanking screw.
(2) Install the 98D07203000 MOORING FITTING - 042 at FR15 LH and 98D07203000MOORING FITTING - 043 at FR15 RH.See FIGURE 06-50-00-991-015-A.
(3) If you use one crane with the spreader beam:
(a) Attach the spreader beam to the crane.
(b) Attach the slings to the spreader beam.
(c) Put the crane in position. Make sure that the jib is directly above the fuselagecenterline.
(d) Attach the slings to the fittings at FR15 LH/RH. It is recommended that you installload cells on the slings to monitor the loads during the leveling/lifting operation.
(4) If you use two cranes:
(a) Attach the slings to each crane.
(b) Put both cranes in position. Make sure that each jib head is directly above FR15LH/RH.
(c) Attach the slings to the fittings at FR15 LH/RH. It is recommended that you installload cells on the slings to monitor the loads during the leveling/lifting operation.
(5) See TASK 06-50-00-581-801-A01 for the general instructions for leveling and lifting withcranes.It is recommended to install a pneumatic lifting bag (see 06-40-00) below the aft fuselageto prevent tail tipping.
06-50-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
1.97
5 m
(6.4
8 ft)
1.97
5 m
(6.4
8 ft)
6.20 m(20.34 ft)
CL
3.95 m(12.95 ft)
180° SLING ANGLE
N_AR_065000_1_0140101_01_02
FWD Fuselage Crane LiftingStrap at FR15 or FR20
FIGURE-06-50-00-991-014-A01
06-50-00Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
7 HOLES
N_AR_065000_1_0150101_01_00
A
HOISTING USING 1 CRANE: UTILISATION OFFITTING SLINGS AND HOISTING BEAM
HOISTING USING 2 CRANES: UTILISATION OFFITTING AND SLINGS
2.37
m(7
.76
ft)
3.95 m(12.95 ft)
CL
AA
FDL
= =
10.1
0 m
(31.
14 ft
)
FWD Fuselage Crane LiftingFittings at FR15
FIGURE-06-50-00-991-015-A01
06-50-00Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
30
10
20
30
40
50
60
70
80
90
100
110
22
44
66
88
110
132
154
176
198
220
242
40
80 100
50 60
140120
70
160
80
180
90
200 220
100
AIRCRAFTWEIGHT1000 kg
1000 lb
CG 15% CG 20%
CG 25%
CG 30%
CG 35%
LOADS AT FR15 OR FR20100 kg100 lb
N_AR_065000_1_0210101_01_00
MAXIMUM LOAD FOR LIFTING BY SLINGS = 6700 kg (14771 lb)
FWD Fuselage Crane LiftingReaction at FR15 or FR 20 for Lifting by Sling (Sheet 1 of 2)
FIGURE-06-50-00-991-021-A01
06-50-00Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
30
10
20
30
40
50
60
70
80
90
100
110
22
44
66
88
110
132
154
176
198
220
242
40
80 100
50 60
140120
70
160
80
180
90
200 220
100
AIRCRAFTWEIGHT1000 kg
1000 lb
CG 15% CG 20%
CG 25%
CG 30%
CG 35%
LOADS AT FR15100 kg100 lb
MAXIMUM LOAD AT FRAME 15 FOR LIFTING BY 2 FITTINGS = 6700 kg
N_AR_065000_1_0210102_01_00
(14771 lb)
FWD Fuselage Crane LiftingReaction at FR15 for Lifting by Mooring Fittings (Sheet 2 of 2)
FIGURE-06-50-00-991-021-A01
06-50-00Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-50-00-581-802-A01
Wing Rib Attachment Tool
1. GeneralThis task gives the procedure to install and lift the aircraft with the 7K804427D520 CRANEATTACHMENT - WING LIFTING BRACKET attachment tool.
2. InspectionsDo a detailed visual inspection of the wing and specially of the side stay mounting bracket and thecardan pin. Report any sign of damage (nick, crack, etc.).In case of damage, contact AIRBUS.
3. Job Setup ReferencesThis procedure gives details to level/lift the aircraft by the wings when one or the two main landinggear(s) or all the landing gears are retracted, collapsed or missing. See TASK 06-50-00-581-803-A01.You can use this task in combination with the Forward-Fuselage Crane Lifting procedure (see TASK06-50-00-581-803-A01) or one other lifting method (jacking or use of pneumatic lifting bags).
A. Allowable loadsThe maximum allowable lifting load on each cardan pin eye-end is 25500 daN (56200 lbf).
B. LimitationsTo do this procedure, the pitch or roll angle of the aircraft must be less than 10˚.If the pitch or roll angle is more than 10˚, lateral loads can be applied to the mounting bracketand secondary damage can occur. Contact AIRBUS to determine an alternative solution.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATION7K804427D520 CRANE ATTACHMENT - WING LIFTING BRACKET
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONTASK 06-50-00-581-803-A01 TASK 06-50-00-581-803-A01-Forward Fuselage Crane Lifting
TASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Deviceson Landing Gears
TASK 06-50-00-581-801-A01 TASK 06-50-00-581-801-A01-General Preparation andinstructions for Leveling and Lifting th
03-00-00 03-00-00-WEIGHT AND CG MANAGEMENT06-10-00 06-10-00-LOAD DETERMINATION
06-50-00Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
REFERENCE DESIGNATIONFIGURE 06-50-00-991-016-A FIGURE 06-50-00-991-016-A-Cardan PinFIGURE 06-50-00-991-018-A FIGURE 06-50-00-991-018-A-Crane Lifting
FIGURE 06-50-00-991-013-A FIGURE 06-50-00-991-013-A-Over wing Panel
Referenced Information
TABLE 2
5. Procedure
WARNING : BE CAREFUL WHEN YOU DO THIS PROCEDURE. OBEY THE EQUIPMENTMANUFACTURERS’ HEALTH AND SAFETY INSTRUCTIONS AND YOUR LOCALREGULATIONS. INJURY CAN OCCUR IF YOU DO NOT OBEY THESEINSTRUCTIONS.
CAUTION : BEFORE YOU USE THE WING RIB ATTACHMENT TOOL, YOU MUST DO AFULL INSPECTION OF THE WING.IF YOU FIND DAMAGE, YOU MUST NOT USE THE WING RIB ATTACHMENTTOOL TO LIFT THE AIRCRAFT.
CAUTION : THE ANGLE OF THE LIFTING CABLE AT MLG POSITION MUST NOT BE MORETHAN 10 DEGREES IN ANY DIRECTION. THIS CAN CAUSE DAMAGED TO THETOP WING SKIN AND THE STRUCTURE.
Subtask 06-50-00-010-001-A01
A. Preparation
WARNING : BEFORE YOU START WORK ON THE WINGS, PYLONS OR LANDING GEAR,YOU MUST PUT ON AND ATTACH A SAFETY HARNESS. WITHOUT ASAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOUINJURY.
WARNING : YOU MUST MONITOR AIRCRAFT STABILITY, WEIGHT AND CG DURINGTHE RECOVERY PROCESS.
(1) Before you start work, make sure that:- The aircraft is stable- The aircraft defueled, if necessary or possible- The electrical systems are de-energized- The hydraulic systems are de-pressurized- No weight or load is applied to the main landing gears before you disconnect the side
stay assembly. If weight or load is applied to the main landing gears, you must supportthe wings with jacks, pneumatic lifting bags, shoring cradles or a combination of these.
(2) Calculate the weight and CG of the aircraft, see 03-00-00.
06-50-00Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(3) Calculate the lifting loads at each attachment position, see 06-10-00.
(4) Make sure that the lifting loads are not more than the allowable load of the cardan pineye-end.
Subtask 06-50-00-581-004-A01
B. Installation of the Crane Attachment
WARNING : THE MAIN LANDING GEAR WILL NOT SUPPORT THE WEIGHT OF THEAIRCRAFT WHEN THE SIDE-STAYS ARE DISCONNECTED. ONCE LIFTED,YOU MUST SUPPORT THE AIRCRAFT WITH JACK, PNEUMATIC LIFTINGBAGS, SHORING CRADLES OR A COMBINATION OF THESE.ALTERNATIVELY, PUT THE AIRCRAFT ON A SUITABLE ADAPTEDFLATBED TRAILER FOR TOWING AWAY FROM THE CRASH SITE.
(1) Get access to the upper cardan pin of the MLG side-stay, use one of the methods thatfollow:- Remove the overwing panel
Or- Cut an access hole in the overwing panel to the dimension of the 7K804427D520
CRANE ATTACHMENT - WING LIFTING BRACKET with sufficient clearance, seeFIGURE 06-50-00-991-013-A.
WARNING : BE CAREFUL WHEN YOU REMOVE COMPONENTS FOR ACCESS. BEFOREYOU REMOVE THE COMPONENTS, MAKE SURE THAT THE RELATEDSYSTEM(S) IS(ARE) DE-ENERGIZED/DEPRESSURIZED. IF YOU USE TOOLSTO REMOVE COMPONENTS, MAKE SURE THAT YOU DO NOT CAUSEDAMAGE TO THE ADJACENT STRUCTURE OR SYSTEMS.
(2) Remove all the pipes, ducts or electrical wirings that can touch the lifting bracket wheninstalled.
(3) Make sure that the aircraft is fully supported and no load is applied to the landing gears.
(4) Disconnect the MLG side-stay assembly from the eye-end attachment of the upper cardanpin as follow (see FIGURE 06-50-00-991-016-A):
(a) Unlock the tab washer and remove the attachment bolt.
(b) Remove the two end caps.
(c) Remove the pin from the attachment joint.
(d) Disconnect the MLG side-stay from cardan pin eye-end attachment.
WARNING : BE CAREFUL WHEN YOU HANDLE THIS EQUIPMENT. THIS EQUIPMENT ISHEAVY (MORE THAN 12KG (26.5 LB)) AND CAN CAUSE INJURY AND/ORDAMAGE.
06-50-00Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(5) Put the 7K804427D520 CRANE ATTACHMENT - WING LIFTING BRACKET in positionon the eye-end of the upper cardan pin. See FIGURE 06-50-00-991-018-A.
NOTE : You can attach the bracket to the crane with the sling first to help you installthe tool on the aircraft.
(6) Install the pin on the eye-end of the cardan pin and through the lifting bracket.
NOTE : The pin dimension can change with aircraft variants. Make sure that you use thecorrect pin through the eye-end of the cardan pin and lifting bracket.The thread of the pin is 87 mm (3.43 in) for A318, A319, A320 and A321-100and is 27 mm (1.06 in) for A321-200.
(7) Install the safety bolt to safety the pin.
(8) Make sure that the MLG and its attachment are safe and will no move during the recoveryoperation.If necessary and if possible, use cable slings or other attachment system (see TASK02-30-01-481-801-A01 for the installation of the L/G safety devices) to safely attach themain landing gear and prevent sudden retraction.
(9) If it is necessary to lift the two wings of the aircraft, do again the steps for the other wing.
Subtask 06-50-00-581-005-A01
C. Lifting
WARNING : THE AIRCRAFT MUST NOT REST ON ITS MAIN LANDING GEAR WHENYOU LIFT THE WING WITH THE CRANE LIFTING BRACKET. THE MLGWILL NOT SUPPORT THE WEIGHT OF THE AIRCRAFT AND CANCOLLAPSE.
CAUTION : THE ANGLE OF THE LIFTING CABLE AT MLG POSITION MUST NOT BEMORE THAN 10 DEGREES IN ANY DIRECTION. THIS CAN CAUSEDAMAGED TO THE TOP WING SKIN AND THE STRUCTURE.
CAUTION : YOU MUST DO THE LATERAL LEVELING BEFORE YOU DO THELONGITUDINAL LEVELING.
(1) Attach the lifting cables to the mobile crane(s).
(2) Put the crane(s) in position. Make sure that the jib head of the crane is directly above thelifting bracket.
(3) Attach the lifting cables to the lifting bracket. See FIGURE 06-50-00-991-018-A for anexample of general configuration.
(4) See TASK 06-50-00-581-801-A01 for the general instructions for leveling and lifting withcranes.
(5) Level the aircraft wings.
06-50-00Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(6) If necessary, level the aircraft fuselage. See TASK 06-50-00-581-803-A01.
(7) Lift the aircraft:
(a) Make sure that the aircraft is always level during the lifting operation.
(b) Make sure that the angle of the lifting cable is not more than 10 degrees from thevertical in all directions. See FIGURE 06-50-00-991-018-A.
(8) During the complete leveling and lifting operation, use load cells to monitor the loads andmake sure that the loads applied are not more than the maximum allowable loads.
(9) When the lifting is completed, install the aircraft on prepared supports (jacks, pneumaticlifting bags, recovery trailers, etc.).
06-50-00Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
610 mm(24 in)
100 mm(3.93 in)
100 mm(3.93 in)
10 mm (0.39 in) FROMAFT EDGE OF JOINT STRIP
30 mm (1.18 in) FROM CENTRE OFSTIFFENER FASTENERS, FORWARD ROW
ACCESSHOLE
EDGE OFFAIRING SEAL
AFWD
A
N_AR_065000_1_0130101_01_00
Over wing PanelAccess
FIGURE-06-50-00-991-013-A01
06-50-00Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_065000_1_0160101_01_00
A
B
B
A
REAR SPAR END CAP
SIDE STAYMOUNTINGBRACKET
CARDAN PIN
END CAP
ATTACHMENT BOLT
PIN
SIDE STAYASSEMBLY
TAB WASHER
B B
Cardan PinSide Stay Assembly
FIGURE-06-50-00-991-016-A01
06-50-00Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
10°
10°
CA
RD
AN
PIN
EY
E−
EN
D
SA
FE
TY
BO
LT
JAC
K F
ITT
ING
SID
E S
TA
Y F
ITT
ING
LIF
TIN
G B
RA
CK
ET
SH
AC
KLE
PIN
MA
XIM
UM
ALL
OW
AB
LE D
EV
IAT
ION
OF
TH
E C
RA
NE
S L
IFT
ING
CA
BLE
SF
RO
M T
HE
VE
RT
ICA
L IS
10
DE
GR
EE
SIN
ALL
DIR
EC
TIO
NS
.
SID
E S
TA
YM
OU
NT
ING
BR
AC
KE
TC
AR
DA
N P
IN
BB
10°
10°
N_A
R_0
6500
0_1_
0170
101_
01_0
1
B
B
Crane AttachmentWing Lifting Bracket
FIGURE-06-50-00-991-017-A01
06-50-00Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
THE OVERWING PANELIS REMOVED OR CUTTO GAIN ACCESS
NOTE: TYPICAL ARRANGEMENT
N_AR_065000_1_0180101_01_01
Crane LiftingExample of Crane ArrangementFIGURE-06-50-00-991-018-A01
06-50-00Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 06-50-00-581-801-A01
General Preparation and Instructions for Leveling and Lifting the Aircraft with Cranes
1. GeneralThis section gives the data related to the use of crane for leveling and lifting.
2. InspectionsNot Applicable.
3. Job Setup ReferencesCrane/sling travel range is related to the attitude of the aircraft. See TBD for information related tothe applicable scenario.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATION98D07203003 FUSELAGE SHORING CRADLE98D57004031 WING SHORING CRADLE
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONTASK 03-50-01-558-803-A01 TASK 03-50-01-558-803-A01-Ballast Added EffectTASK 06-50-00-581-803-A01 TASK 06-50-00-581-803-A01-Forward Fuselage Crane Lifting
TASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Deviceson Landing Gears
DESC 06-00-00-002-A01 DESC 06-00-00-002-A01-Leveling/Lifting Obstructions
DESC 06-40-00-001-A01 DESC 06-40-00-001-A01-Pneumatic Lifting Bags on Fuselage
04-30-00 04-30-00-TETHERING THE AIRCRAFT03-50-01 03-50-01-MANAGING AIRCRAFT WEIGHT AND CG05-50-00 05-50-00-CARGO COMPARTMENTS05-60-00 05-60-00-REMOVAL OF LARGE COMPONENTS06-10-00 06-10-00-LOAD DETERMINATION05-10-00 05-10-00-DEFUELING07-20-00 07-20-00-PREPARING A ROADWAY07-40-00 07-40-00-TOWING AND DEBOGGING
06-50-00Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
REFERENCE DESIGNATIONAMM 07-11-00-581-001
Referenced Information
TABLE 2
5. Procedure
WARNING : OBEY THESE PRECAUTIONS WHEN YOU DO LEVELING/LIFTING OF THEAIRCRAFT. MAKE SURE THAT THE LIFTING EQUIPMENT IS APPLICABLE FORTHE SPECIFIC CONDITIONS. MAKE SURE THAT THE PERSONS WHO OPERATETHE LIFTING EQUIPMENT ARE CORRECTLY TRAINED AND HAVE A GOODKNWOLEDGE OF THE SYSTEM. MAKE SURE THAT THE NECESSARY SAFETYAREA IS KNOWN AND THAT PERSONS DO NOT GO IN THIS AREA DURINGTHE LEVELING/LIFTING OPERATIONS. LEVELING/LIFTING OF THE AIRCRAFTCAN BE DANGEROUS IF YOU DO NOT OBEY THESE PRECAUTIONS.
CAUTION : MAKE SURE THAT THE LOADS ON THE AIRFRAME ARE LESS THAN THEALLOWABLE LOADS WHEN YOU USE SUPPORTS. THE SUPPORTS APPLYLOADS THAT DO NOT OCCUR IN NORMAL OPERATION.
CAUTION : WHEN YOU LEVEL/LIFT THE AIRCRAFT, YOU MUST CONTINUOUSLYMONITOR AND RECORD THE LOADS AND MAKE SURE THAT THE LOADSYOU APPLY ARE NOT MORE THAN THE MAXIMUM ALLOWABLE LOADS. IFTHE LOADS ARE MORE THAN THE ALLOWABLE LOADS, THIS CAN CAUSEDAMAGE TO THE AIRCRAFT STRUCTURE.
CAUTION : IF THE LOADS APPLIED DURING THE RECOVERY PROCEDURE ARE MORETHAN THE MAXIMUM ALLOWABLE LOADS, YOU MUST CONTACT AIRBUSFOR SPECIFIC INSPECTIONS.
CAUTION : USE ONLY RECOVERY SLINGS AND SPREADER BEAMS SPECIFIED BY AIRBUS.NON-APPROVED LIFTING DEVICES CAN CAUSE SECONDARY DAMAGE TOTHE AIRCRAFT.
CAUTION : MAKE SURE THAT THE CRANE YOU USE CAN LIFT THE ESTIMATED LOADPLUS THE WEIGHT OF THE LIFTING EQUIPMENT BEFORE YOU START TOLIFT THE AIRCRAFT.
CAUTION : YOU MUST CORRECTLY TETHER THE AIRCRAFT BEFORE YOU LEVEL ORLIFT IT.
NOTE : The information or principle contained in this chapter are given as a guide to help anaircraft recovery.
06-50-00Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
NOTE : It is the responsibility of the recovery manager to make the decision about the applicablemethod and related equipment/personnel for the leveling/lifting of the aircraft.
Subtask 06-50-00-581-001-A01
A. General
NOTE : Before you start a leveling or lifting procedure with slings/cranes, make sure that theinstructions that follow are obeyed.
(1) Do not level or lift the aircraft with cranes during gusty wind conditions.
(2) The common maximum permissible wind speed for mobile cranes is 50 km/h (27 kt) withsteady wind. Airbus recommends not to lift the aircraft if the wind speed is higher.It is also recommended not to use cranes during thunderstorm to prevent lightning.
(3) Before you start the leveling or lifting operation with cranes, you must correctly tether theaircraft. This is to prevent uncontrolled movement of the aircraft during this operationspecially in case of high wind condition (See 04-30-00).
(4) Only personnel familiar with the operating procedures of the slings, spreader beams andcranes should be in charge of the lifting operation.
(5) Calculate the NRW and CG position (See 03-50-01).
(6) Calculate the anticipated vertical load on the fuselage or fitting points and make sure thatthe necessary load is not more than the maximum allowable load.If the necessary load is more than the allowable load, you must either decrease the aircraftweight until the lifting load is less than the allowable load or use another leveling or liftingprocedure.
(7) Calculate the total lifting capacity of the slings and cranes that you use are able to hold.Make sure that each available sling or crane can hold the necessary load, and can fit withinthe boundaries of the fuselage contact zone.The crane lifting strength must be higher than the lifting loads and the jib length must besufficient to allow aircraft movement (lateral and vertical)To decrease the necessary lifting load, it is recommended to decrease the aircraft weight byremoval of cargo or payload from the aircraft before start of the leveling or liftingoperation (See 05-50-00 and/or 05-60-00).
(8) Calculate the possible arc movement during the leveling operation, at each lifting point.Also calculate the side load if necessary (See 06-10-00).
(9) For the wing lifting, make sure that the hook and slings can hold the lifting loads.
(10) The frame station and lifting points that will be used for lifting must no be damaged. Incase of damage, contact Airbus.
(11) Make sure that there are no sharp edges or peaks (skin damages, protruding structure,antenna ... ) in the zones where the fuselage recovery slings will be installed.See DESC 06-00-00-002-A01 for the list of leveling/lifting obstructions.
06-50-00Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(12) If necessary, put wheel chocks in front of and behind the wheels of the main landing gearthat is extended and in contact with the ground.
(13) Install the landing gear downlock pins in all landing gears that are extended.
(14) All the persons who work on the leveling/lifting operation should be connected with mobilecommunication devices. Two-way voice activated headsets are ideal for this type ofoperation.
(15) No personnel must be in or below the aircraft during the leveling process. The personnelwho is not directly involved in the lifting operation must be at least 20 m (65 ft) far fromthe aircraft and cranes.
(16) Movement of fuel in the wing tanks caused by aircraft leveling can change the aircraft CGposition. Therefore, it is recommended to remove all fuel from the aircraft before leveling.(See 05-10-00) This will also decrease the necessary lifting loads.
(17) Monitor the CG during all the aircraft leveling process and be prepared to control withballast if necessary (See TASK 03-50-01-558-803-A01).
(18) Monitor the position of the slings carefully at all times during the leveling/lifting process.For the fuselage lifting, it is necessary to instal each sling at a frame station and all slingsmust be in the area listed in TASK 06-50-00-581-803-A01.
(19) You must monitor and record the applied loads at all times during the leveling and liftingprocess. If at one step of the process the maximum load (related to the lifting scenario) ismore than the allowable load, contact Airbus for definition of structure inspection tasks.Airbus recommends that you use load cells and monitoring equipment to record the appliedloads.
(20) Level or lift the aircraft slowly, obey the instructions given by the manufacturer of thelifting/leveling equipment and adjust the tethers as the aircraft starts to move.
(21) When the fuselage and the wing are leveled and if it is necessary to lift the aircraft, it isrecommended to use the 3 main jacking points to lift the aircraft to the necessary height.See AMM 07-11-00-581-001. The aircraft should not be lifted until the entire aircraft (wingand fuselage) is in a level attitude.
(22) When the aircraft is leveled and at the necessary height:
(a) Assemble a shoring device to support the fuselage and/or wings, or install jacks as asafety precaution if you work on the landing gear. Use shoring cradles on a preparedarea:- Under the fuselage FR9, F24-56 and FR60: 98D07203003 FUSELAGE SHORING
CRADLE,- Under the wing RIB 4, RIB 13 and RIB 22: 98D57004031 WING SHORING
CRADLE.If the above tools are not available on site, you can use wood cribbing with rubberprotections under the fuselage. In that case, the bearing area is the same as forpneumatic lifting bags installation: see DESC 06-40-00-001-A01.
06-50-00Page 22
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(b) If possible on site, when the aircraft is on shoring cradles, extend the landing gear andinstall the downlock pins, see TASK 02-30-01-481-801-A01 or repair or replace thelanding gear.Then prepare a roadway (see 07-20-00) and tow the aircraft (see 07-40-00).
(c) Or place the forward fuselage and/or the wing(s) on a mobile trailers if it is notpossible to make the landing gear serviceable.
(23) After the recovery operation, you must do an inspection of the skin surface and the wingfor any sign of damage which may have been caused during the leveling/lifting.
06-50-00Page 23
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
MOVING THE AIRCRAFT
07-00-00 MOVING THE AIRCRAFT
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-00-00-002-A01
General Preparation
1. GeneralThis chapter gives the procedures for moving the aircraft to a hard surface. There are differentprocedures for moving the aircraft if the landing gear is serviceable, or if it is damaged.
A. Before moving the aircraft you must:- Do a detailed inspection of the landing gear to confirm its structural integrity. The landing
gear must be capable of supporting the weight of the aircraft during Towing/Deboggingoperations, see 02-30-01
- Do a check to make sure that the landing gear is in the downlocked position with thegroundlock pins fitted. If it is not possible to fit the groundlock pins, a more detailedinspection must be done to find the cause. See 02-30-01 for groundlock pin installationdetails.
B. Use one of the following procedures when the landing gear is damaged or missing:- Repair or replace the landing gear to make it capable of supporting the aircraft weight
during Towing/Debogging operations.- Use an aircraft recovery transport vehicle or vehicles to move the aircraft. See 07-60-00.
C. Before moving the aircraft, make sure that:- Fuel and cargo have been removed to make the aircraft as light as possible.- The weight and Center of Gravity (CG) are adequate for towing stability, seeTBD- The relevant authorities have confirmed that the aircraft can be moved.- The airport authority and fire department have been told that the recovery process has
moved to the next phase.- There are no fluid leaks.
2. Returning Undamaged Aircraft to a Hard SurfaceA planned recovery will allow the undamaged aircraft to be returned to the runway in the leastpossible time.
A. The recovery plan can include:- Confirmation that the aircraft is in the correct condition to be moved.- The need to remove fuel and cargo from the aircraft.- The type of ground over which the aircraft must be moved.- The direction in which the aircraft will be moved.- The type and quantity of ground equipment and recovery vehicles needed.
07-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
B. The following procedures may be necessary to return an undamaged aircraft to the runway ortaxiway:- For an aircraft that has moved onto soft ground or snow, it may be necessary to use the
Debogging procedure, TBD and the procedure to prepare a roadway 07-20-00. When aroadway is prepared, the width of the roadway must be sufficient to let the towing vehicleturn the aircraft if necessary.
- To make sure that the towing loads are not exceeded; use a load measuring tool to monitorthe loads at all times.
- To make sure that the Debogging loads are not exceeded; use a load measuring tool tomonitor the loads at all times unless the fuse assembly is being used, see TBD.
07-00-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-20-00 PREPARING A ROADWAY
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-20-00-001-A01
General
1. For each aircraft recovery, the recovery manager must contact the relevant specialists to obtaincorrect data applicable to the ground strength.If the aircraft has moved off the runway or taxiway, it may be necessary to build a roadway to movethe aircraft on.The roadway must be excavated to a depth that will let the finished roadway safely support theweight of the aircraft.The width of the roadway must let the aircraft be turned as necessary and let the routing of theaircraft be changed. The width of the roadway must let heavy recovery vehicles manoeuvre safely.
NOTE : The information or principle contained in this chapter are given as a guide to assist anaircraft recovery.
2. If the ground is soft or is not stable, you must excavate the ground along the route to the runwayand build a roadway. If the aircraft wheels have made ruts that are not too deep, the ruts can befilled with a foundation material.This material can be compacted gravel or railway ties/sleepers covered with sheet steel or thickplywood, see FIGURE 07-20-00-991-001-A.See chapter 04-50-00 for information on soil characteristics. Normally, general constructioncontractors will have sufficient knowledge and experience to make a safe roadway.Some of the materials that can be used in the construction of a roadway are:- Compacted stone, gravel and/or broken asphalt,- Railway ties/sleepers,- Sheet steel,- PlywoodSee chapter 09-30-01 for details of materials that can be used for the recovery operation. You mustmake sure that materials used for recovery are safe to be used, can cope with the forecasted weatherconditions and will not break under load or cause a change in aircraft stability.When sheet material is used on top of the compacted material, it is recommended that two layers ofsheet material are used. Lay the sheets with the joints of the bottom layer covered by the top layer,see FIGURE 07-20-00-991-001-A. When using sheet steel be careful to avoid fluid spills. Fluid spillson sheet steel can cause a loss of towing traction for the towing vehicles and will be a hazard for therecovery team.Steel or aluminum sections that can be bolted together are available commercially in most cities.Fabric matting that is made of different types of glass fibre is also available commercially. There aredifferent types, sizes and strengths of these materials.If there is not sufficient sheet material to make the roadway, the materials that the aircraft has beenmoved over can be re-used to complete the roadway.
07-20-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
If heavy timbers are used directly on the roadway, they must be covered with a layer of plywood orsteel. If this is not done, the load from individual wheels can push one of the timbers into soft groundand cause the aircraft to stop.When the ground is not level, the roadway must normally be made with a slope of 5˚ or less. Ifpossible, position the towing/winching vehicle on the runway to give maximum traction.
07-20-00Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
5° SLOPE
SHEET MATERIALOVERLAP
TYPICAL USE OFRAILWAY TIES/SLEEPERS
EXCAVATED AREA FILLEDWITH FOUNDATION MATERIAL
N_AR_072000_1_0010101_01_00
Preparing a RoadwayTypical Roadway Construction (Sheet 1 of 3)
FIGURE-07-20-00-991-001-A01
07-20-00Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
(STEEL PLATES, FIBERGLASS, ALUMINIUM, ...)RUNWAY MATING
N_AR_072000_1_0010102_01_00
Preparing a RoadwayTypical Roadway Construction (Sheet 2 of 3)
FIGURE-07-20-00-991-001-A01
07-20-00Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CONCRETE
N_AR_072000_1_0010103_01_00
Preparing a RoadwayTypical Roadway Construction (Sheet 3 of 3)
FIGURE-07-20-00-991-001-A01
07-20-00Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-40-00 TOWING AND DEBOGGING
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-40-00-001-A01
General
1. This chapter gives the towing procedures to be used during an aircraft recovery.
WARNING : STAY IN COMMUNICATION WITH THE AIRFIELD OPERATING AUTHORITY/AIRTRAFFIC CONTROLLER DURING THIS PERIOD AND GET THEIR PERMISSIONTO MOVE THE AIRCRAFT.
- For towing load and angle limits, see 07-40-04,- For towing with the nose gear, see 07-40-01.- For towing with the main gear from the front, see TASK 07-40-02-584-801-A01,- For towing with the main gear from the rear, see TASK 07-40-02-584-802-A01,- For towing with deflated tires, see 07-40-03.For AMM towing procedure, see AMM 09-10-00PB201.
2. Debogging definition :Airbus considers that debogging is towing on soft ground, with or without slope consideration.
07-40-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-40-01 TOWING FROM THE NOSE LANDING GEAR
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 07-40-01-584-801-A01
Towing on the NLG with a Towbar
1. GeneralThis procedure gives details to push the aircraft rearward or to tow the aircraft forward using atowbar installed on the NLG.
2. Inspections- Make sure that the safety devices are installed on the landing gears, see TASK 02-30-01-481-801-
A01.- Make sure that the aircraft is stable, see TBD or AMM 05-57-00-200-001.- Make sure that the engine cowl are closed.
3. Job Setup ReferencesFor towing limits, see 07-40-04.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATIOND23156000 PIN-SAFETY
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Devices
on Landing Gears
07-40-04 07-40-04-TOWING LOAD LIMITSAMM 05-57-00-200-001AMM 31-60-00-860-001AMM 29-24-00-863-001FIGURE 07-40-01-991-002-A FIGURE 07-40-01-991-002-A-Towing on the NLG
FIGURE 07-40-01-991-001-A FIGURE 07-40-01-991-001-A-Towing on the NLG
Referenced Information
TABLE 2
07-40-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
Subtask 07-40-01-500-001-A01
A. Preparation
(1) If possible, do an EIS start procedure, see AMM 31-60-00-860-001.
(2) On the N/W steering deactivation electrical-box 5GC (see FIGURE 07-40-01-991-002-A):
(a) Set the ground-towing control lever to the towing position.
(b) Install the D23156000 PIN-SAFETY.
Subtask 07-40-01-500-002-A01
B. Installation of the Towbar
CAUTION : MAKE SURE THAT THE TOW BAR AS A DAMPING SYSTEM, ACALIBRATED SHEAR PIN AND TWO CALIBRATED TURN SHEAR PINS.THIS IS TO PREVENT HIGH LOADS WHICH CAN CAUSE DAMAGE TO THELANDING GEAR.
(1) Install the towbar on the tow fitting.
(2) Connect the towbar to the tractor.See FIGURE 07-40-01-991-001-A.
Subtask 07-40-01-869-001-A01
C. Aircraft Configuration
(1) On the panel 400VU:- Make sure that the pressure indication on the yellow brake-pressure triple-indicator is
correct: 3000 psi (206.84 bar). The pointer must be in the green area. The pointermust be in the green range.
- If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
(2) On the panel 110VU, set the PARKING-BRK control-switch to OFF.
(3) During towing, make sure that the pressure indication on the yellow brake-pressure triple-indicator is correct: 3000 psi (206.84 bar). The pointer must be in the green area. Thepointer must be in the green range.If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
07-40-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 07-40-01-584-001-A01
D. Towing
WARNING : DURING TOWING / TAXIING OPERATION (LOW-SPEED OPERATIONINCLUDED), EACH PERSON IN THE AIRCRAFT MUST BE IN A SEAT ANDTHE SEAT BELT MUST BE FASTENED. IF THE SEAT BELT IS NOTFASTENED, THERE IS A RISK OF INJURY IF THE AIRCRAFT STOPSSUDDENLY.
CAUTION : PUT THE PARKING BRAKE CONTROL SWITCH IN THE OFF POSITIONBEFORE YOU TOW OR PUSH BACK THE AIRCRAFT. THIS IS TOPREVENT HIGH LOADS WHICH CAN CAUSE DAMAGE TO THE NOSELANDING GEAR.
(1) Tow slowly and smoothly.During the towing operations, put:- one person in the cockpit to operate the brakes if necessary,- two persons to monitor the wing tips.
NOTE : The shock absorber reaction can cause the aircraft to move forward and rearwardwhen you stop the wheels. Because of this, make sure that there is sufficientspace around the aircraft when you tow with the nose gear.
Subtask 07-40-01-869-002-A01
E. Close-up
(1) Visual Inspection
(a) After you complete the towing operation, make sure that the nose wheels are alignedwith the aircraft centerline.
(2) Aircraft Configuration
(a) Put the wheel chocks in position in front of and behind the wheels.
(b) On the panel 110VU, set the PARKING BRK control switch to ON.
(c) On the panel 400VU, make sure that the pressure indication on the yellow brake-pressure triple-indicator is correct: 3000 psi (206.84 bar). The pointer must be in thegreen area. The pointer must be in the green range.If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
(3) Removal of the Towbar
(a) Remove the towbar from the fitting of the NLG.
(b) Remove the tow-lever safety pin.
(c) Set the ground-towing lever to its initial position.
07-40-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
A
TORSION
PUSH PULL
TURNING POINT WITH RUBBER
B
B
A
N_AR_074001_1_0010101_01_00
Towing on the NLGTowing Attachment
FIGURE-07-40-01-991-001-A01
07-40-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TOWING LEVER
(NOSE WHEEL STREERING OPERATIONAL)NORMAL POSITION
(TOWING POSITION)SAFETY PIN
(NOSE WHEEL STEERING DEACTIVATED)TOWING POSITION
N_AR_074001_1_0020101_01_00
A
A
Towing on the NLGN/W-Steering Deactivation Electrical-Box
FIGURE-07-40-01-991-002-A01
07-40-01Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 07-40-01-584-802-A01
Towing on the NLG with a Towbarless Tractor
1. GeneralThis procedure gives details to push the aircraft rearward or to tow the aircraft forward using atowbarless tractor on the NLG.
2. Inspections- Make sure that the safety devices are installed on the landing gears, see TASK 02-30-01-481-801-
A01.- Make sure that the aircraft is stable, see TBD or AMM 05-57-00-200-001.- Make sure that the engine cowl are closed.
3. Job Setup ReferencesFor towing limits, see 07-40-04.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATIOND23156000 PIN-SAFETY
Fixtures, Tools, Test and Support
TABLE 1
B. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Devices
on Landing Gears
TASK 07-40-01-584-801-A01 TASK 07-40-01-584-801-A01-Towing with the NLG with aTowbar
07-40-04 07-40-04-TOWING LOAD LIMITSAMM 05-57-00-200-001AMM 31-60-00-860-001AMM 29-24-00-863-001
Referenced Information
TABLE 2
07-40-01Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
5. Procedure
WARNING : WHEN YOU TOW THE AIRCRAFT WITH A TOWBARLESS TRACTOR, THEPARKING BRAKE OR THE BRAKE PEDALS SHALL ONLY BE USED IN CASE OFEMERGENCY. IF YOU APLLY THE PARKING BRAKE OR THE BRAKE PEDALS,YOU CAN CAUSE OVERLOAD TO THE NLG, DAMAGE TO THE TOWBARLESSTRACTOR AND INJURY TO THE PERSONEL. IF THIS OCCURS, YOU MUSTCONTACT AIRBUS.
CAUTION : WHEN YOU USE A TOWBARLESS TRACTOR, MAKE SURE THAT YOU OBEYFULLY ALL THE INSTRUCTIONS IN THIS PROCEDURE. IF YOU DO NOT, THETRACTOR CAN CAUSE IMPORTANT SCRAPING OR OTHER DAMAGE TO THENLG AND TO THE AIRFRAME STRUCTURE AROUND THE NLG.
Subtask 07-40-01-500-003-A01
A. Preparation
(1) If possible, do an EIS start procedure, see AMM 31-60-00-860-001.
(2) On the N/W steering deactivation electrical-box 5GC (see TASK 07-40-01-584-801-A01):
(a) Set the ground-towing control lever to the towing position.
(b) Install the D23156000 PIN-SAFETY.
Subtask 07-40-01-500-004-A01
B. Installation of the Towbarless Tractor
CAUTION : AIRBUS STRONGLY RECOMMENDS THAT THE OPERATORS OFTOWBARLESS TRACTORS CAREFULLY ALIGNS THE CLAMPING DEVICEOF THE TRACTOR WITH THE NOSE LANDING GEAR AXIS. THE GAPBETWEEN THE CRADDLE AND THE TORQUE-LINK IS VERY SMAL AND AMISALIGNMENT CAN CAUSE DAMAGE TO THE TORQUE-LINK PIN. ASIMPLE ALIGNMENT DEVICE ON THE TRACTOR (MARKING, METALINDICATOR, ETC. SUPPLIED BY THE MANUFACTURER OF THETOWBARLESS TRACTOR OR MANUFACTURED LOCALLY) CAN HELP THEDRIVER.
(1) There are special approval procedures for towbarless tractors. Before towing, make surethat the towbarless is approved for the towing of this aircraft. For more information on thetowbarless tractors, see the SIL 090-002.
(2) Set the aircraft type on the towbarless tractor, if necessary.
(3) Align the clamping device of the tractor with the NLG axis.
(4) Lock on and lift the NLG.
07-40-01Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(5) Make sure that the nose landing gear is correctly on the center of the tractor platform andcannot be disengaged from the tractor.
Subtask 07-40-01-869-003-A01
C. Aircraft Configuration
(1) On the panel 400VU:- Make sure that the pressure indication on the yellow brake-pressure triple-indicator is
correct: 3000 psi (206.84 bar). The pointer must be in the green area. The pointermust be in the green range.
- If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
(2) On the panel 110VU, set the PARKING-BRK control-switch to OFF.
(3) During towing, make sure that the pressure indication on the yellow brake-pressure triple-indicator is correct: 3000 psi (206.84 bar). The pointer must be in the green area. Thepointer must be in the green range.If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
Subtask 07-40-01-584-002-A01
D. Towing
WARNING : DURING TOWING / TAXIING OPERATION (LOW-SPEED OPERATIONINCLUDED), EACH PERSON IN THE AIRCRAFT MUST BE IN A SEAT ANDTHE SEAT BELT MUST BE FASTENED. IF THE SEAT BELT IS NOTFASTENED, THERE IS A RISK OF INJURY IF THE AIRCRAFT STOPSSUDDENLY.
CAUTION : PUT THE PARKING BRAKE CONTROL SWITCH IN THE OFF POSITIONBEFORE YOU TOW OR PUSH BACK THE AIRCRAFT. THIS IS TOPREVENT HIGH LOADS WHICH CAN CAUSE DAMAGE TO THE NOSELANDING GEAR.
(1) Tow slowly and smoothly.During the towing operations, put:- one person in the cockpit to operate the brakes if necessary,- two persons to monitor the wing tips.
NOTE : The shock absorber reaction can cause the aircraft to move forward and rearwardwhen you stop the wheels. Because of this, make sure that there is sufficientspace around the aircraft when you tow with the nose gear.
07-40-01Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 07-40-01-869-004-A01
E. Close-up
(1) Visual Inspection
(a) After you complete the towing operation, make sure that the nose wheels are alignedwith the aircraft centerline.
(2) Aircraft Configuration
(a) On the panel 110VU, set the PARKING BRK control switch to ON.
(b) On the panel 400VU, make sure that the pressure indication on the yellow brake-pressure triple-indicator is correct: 3000 psi (206.84 bar). The pointer must be in thegreen area. The pointer must be in the green range.If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
(3) Removal of the Towbarless Tractor
(a) Remove the NLG from the towbarless tractor.
(b) Put the wheel chocks in position in front of and behind the wheels.
(c) Remove the tow-lever safety pin.
(d) Set the ground-towing lever to its initial position.
07-40-01Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-40-02 TOWING FROM THE MAIN LANDING GEAR
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 07-40-02-584-801-A01
Towing with the Main Gear from the Front
1. GeneralThis procedure gives details to tow the aircraft forward with the MLG.
2. Inspections- Make sure that the safety devices are installed on the landing gears, see TASK 02-30-01-481-801-
A01.- Make sure that the aircraft is stable, see TBD or AMM 05-57-00-200-001.- Make sure that the engine cowl are closed.- Only tow the aircraft if the ground conditions let you. If necessary, put down the applicable
surface equipment: slopes, movable taxiway plates, etc. (see 07-20-00).Only try to turn if the ground conditions let you.Do a detail visual inspection of the towing cables, the fuse pins, the towing attachments beforeyou do this procedure.
3. Job Setup ReferencesDepending on the landing gear configuration, there are two methods of towing the aircraft from thefront with the MLG:- Using a towing strap around the MLG, see SUBTASK 07-40-02-500-002-A01,- Using two 98D09104000001 ATTACHMENT - TOWING or 98D09104002000 ATTACHMENT -
TOWING (OPTIONAL 4 WHEEL BOGIE MLG), see SUBTASK 07-40-02-500-003-A01.For towing limits, see 07-40-04.
4. Job Set-up Information
A. Fixtures, Tools, Test and Support
REFERENCE DESIGNATIOND23156000 PIN-SAFETY98A09003500000 CABLE-TOWING, MLG
98D09104000001 ATTACHMENT - TOWING98D09104002000 ATTACHMENT - TOWING (OPTIONAL 4 WHEEL BOGIE
MLG)
Fixtures, Tools, Test and Support
TABLE 1
07-40-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
B. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Devices
on Landing Gears
07-40-04 07-40-04-TOWING LOAD LIMITS07-20-00 07-20-00-PREPARING A ROADWAYAMM 05-57-00-200-001AMM 31-60-00-860-001AMM 29-24-00-863-001FIGURE 07-40-02-991-001-A FIGURE 07-40-02-991-001-A-Towing with the MLG from the
FrontFIGURE 07-40-02-991-002-A FIGURE 07-40-02-991-002-A-Towing with the MLG from the
FrontFIGURE 07-40-02-991-003-A FIGURE 07-40-02-991-003-A-Towing with the MLG from the
Front
Referenced Information
TABLE 2
5. Procedure
WARNING : DO NOT USE A MANUAL NOSE WHEEL STEERING BAR DURING TOWINGFROM THE FRONT BECAUSE THE TOWING CABLES WILL BE NEAR THEPERSON AT THE STEERING BAR. DEATH OR INJURY CAN OCCUR IF ATOWING CABLE BREAKS.
Subtask 07-40-02-500-001-A01
A. Preparation
(1) If possible, do an EIS start procedure, see AMM 31-60-00-860-001.
(2) On the N/W steering deactivation electrical-box 5GC:
(a) Set the ground-towing control lever to the towing position.
(b) Install the D23156000 PIN-SAFETY.
Subtask 07-40-02-500-002-A01
B. Installation of the Towing Strap
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE CORRECTLYINSTALLED ON THE LANDING GEAR. THIS PREVENTS UNWANTEDMOVEMENT OF THE LANDING GEAR.
07-40-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
WARNING : MAKE SURE THAT NO PERSONS ARE NEAR THE TOWING CABLES WHENTHE TRACTOR APPLIES TENSION TO THE CABLES. DEATH OR INJURYCAN OCCUR IF A CABLE BREAKS.
(1) Use a towing strap with the properties that follow:- Length 2160 mm (85 in),- Width 100 mm (4 in),- Safe Working Load 1300 daN (29225 lbf).
(2) Wind the towing strap around the bottom of the MLG shock absorber and the axles.Make sure that the towing strap does not touch the links of the MLG. See FIGURE07-40-02-991-001-A.
(3) Connect the 98A09003500000 CABLE-TOWING, MLG to the towing strap.
(4) Connect the 98A09003500000 CABLE-TOWING, MLG to the tractor.
NOTE : Airbus recommends that you install bridge cables or ropes between the towingcables to prevent unwanted cable movement if a cable breaks.
(5) Do SUBTASK 07-40-02-584-001-A01.
Subtask 07-40-02-500-003-A01
C. Installation of the Towing Attachment
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE CORRECTLYINSTALLED ON THE LANDING GEAR. THIS PREVENTS UNWANTEDMOVEMENT OF THE LANDING GEAR.
WARNING : MAKE SURE THAT NO PERSONS ARE NEAR THE TOWING CABLES WHENTHE TRACTOR APPLIES TENSION TO THE CABLES. DEATH OR INJURYCAN OCCUR IF A CABLE BREAKS.
(1) Install the 98D09104000001 ATTACHMENT - TOWING (see FIGURE 07-40-02-991-002-A) or 98D09104002000 ATTACHMENT - TOWING (OPTIONAL 4 WHEEL BOGIE MLG)(see FIGURE 07-40-02-991-003-A) on each MLG.
(2) Install the 98A09003500000 CABLE-TOWING, MLG on the towing attachments.
(3) Connect the 98A09003500000 CABLE-TOWING, MLG to the tractor.
NOTE : Airbus recommends that you install bridge cables or ropes between the towingcables to prevent unwanted cable movement if a cable breaks.
(4) Do SUBTASK 07-40-02-584-001-A01.
07-40-02Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 07-40-02-584-001-A01
D. Towing
WARNING : DURING TOWING / TAXIING OPERATION (LOW-SPEED OPERATIONINCLUDED), EACH PERSON IN THE AIRCRAFT MUST BE IN A SEAT ANDTHE SEAT BELT MUST BE FASTENED. IF THE SEAT BELT IS NOTFASTENED, THERE IS A RISK OF INJURY IF THE AIRCRAFT STOPSSUDDENLY.
WARNING : MAKE SURE THAT NO PERSONS ARE NEAR THE TOWING CABLES WHENTHE TRACTOR APPLIES TENSION TO THE CABLES. DEATH OR INJURYCAN OCCUR IF A CABLE BREAKS.
CAUTION : PUT THE PARKING BRAKE CONTROL SWITCH IN THE OFF POSITIONBEFORE YOU TOW OR PUSH BACK THE AIRCRAFT. THIS IS TOPREVENT HIGH LOADS WHICH CAN CAUSE DAMAGE TO THE NOSELANDING GEAR.
(1) Tow the aircraft slowly and smoothly.During the towing, put:- one person in the cockpit to operate the brakes if necessary,- two persons to monitor the wing tips.
WARNING : DO NOT USE A MANUAL NOSE WHEEL STEERING BAR DURING TOWINGFROM THE FRONT BECAUSE THE TOWING CABLES WILL BE NEAR THEPERSON AT THE STEERING BAR. DEATH OR INJURY CAN OCCUR IF ATOWING CABLE BREAKS.
(2) Where possible, keep the tractor aligned with the aircraft centerline. The maximum lateralposition that is permitted is the width of the aircraft.
NOTE : Airbus recommend that you install load cells on the towing cables to record andmonitor the loads applied on the MLG during the towing.
Subtask 07-40-02-869-001-A01
E. Close-up
(1) Visual Inspection
(a) After you complete the towing operation, make sure that the nose wheels are alignedwith the aircraft centerline.
(2) Aircraft Configuration
(a) Put the wheel chocks in position in front of and behind the wheels.
(b) On the panel 110VU, set the PARKING BRK control switch to ON.
07-40-02Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(c) On the panel 400VU, make sure that the pressure indication on the yellow brake-pressure triple-indicator is correct: 3000 psi (206.84 bar). The pointer must be in thegreen area. The pointer must be in the green range.If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
(3) Removal of the Tooling
(a) Remove the towing cable.
(b) Remove the towing attachment or the towing strap from each MLG.
(c) Remove the tow-lever safety pin.
(d) Set the ground-towing lever to its initial position.
07-40-02Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_074002_1_0010101_01_00
TOWING CABLE
TOWING STRAP
A
A
Towing with the MLG from the FrontStrap Installation
FIGURE-07-40-02-991-001-A01
07-40-02Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_074002_1_0020101_01_00
A
TOWING CABLE
TOWING ATTACHMENT
A
Towing with the MLG from the FrontTowing Attachment Tool - Two Wheel MLG
FIGURE-07-40-02-991-002-A01
07-40-02Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_074002_1_0030101_01_00
TOWING CABLE
TOWING ATTACHMENT
A
A
Towing with the MLG from the FrontTowing Attachment Tool - Four Wheel Bogie MLG (Optional A320 Only)
FIGURE-07-40-02-991-003-A01
07-40-02Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 07-40-02-584-802-A01
Towing with the Main Gear from the Rear
1. GeneralThis procedure gives details to tow the aircraft rearward with the MLG.
2. Inspections- Make sure that the safety devices are installed on the landing gears, see TASK 02-30-01-481-801-
A01.- Make sure that the aircraft is stable, see TBD or AMM 05-57-00-200-001.- Make sure that the engine cowl are closed.- Only tow the aircraft if the ground conditions let you. If necessary, put down the applicable
surface equipment: slopes, movable taxiway plates, etc. (see 07-20-00).Only try to turn if the ground conditions let you.Do a detail visual inspection of the towing cables, the fuse pins, the towing attachments beforeyou do this procedure.
3. Job Setup ReferencesFor towing limits, see 07-40-04.
4. Job Set-up Information
A. Consumable Materials
REFERENCE DESIGNATION05-047 Anti Corrosion Compound (High Temperature Silicone Sealant)
09-016 Corrosion Inhibiting Fillet Consistency
Consumable Materials
TABLE 1
B. Fixtures, Tools, Test and Support
REFERENCE DESIGNATIOND23156000 PIN-SAFETY98D09104001000 ATTACHEMENT-TOWING98D09104002000 ATTACHMENT - TOWING (OPTIONAL 4 WHEEL BOGIE
MLG)
98A09003500000 CABLE-TOWING, MLG
98A09003000001 BAR-STEERING, NOSE WHEEL
Fixtures, Tools, Test and Support
TABLE 2
07-40-02Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
C. Referenced Information
REFERENCE DESIGNATIONTASK 02-30-01-481-801-A01 TASK 02-30-01-481-801-A01-Installation of the Safety Devices
on Landing Gears
07-40-04 07-40-04-TOWING LOAD LIMITS07-20-00 07-20-00-PREPARING A ROADWAYAMM 05-57-00-200-001AMM 31-60-00-860-001AMM 29-24-00-863-001FIGURE 07-40-02-991-004-A FIGURE 07-40-02-991-004-A-Towing with MLG from the Rear
FIGURE 07-40-02-991-005-A FIGURE 07-40-02-991-005-A-Towing with MLG from the Rear
FIGURE 07-40-02-991-006-A FIGURE 07-40-02-991-006-A-Towing with MLG from the Rear
FIGURE 07-40-02-991-007-A FIGURE 07-40-02-991-007-A-Towing with MLG from the Rear
Referenced Information
TABLE 3
5. Procedure
Subtask 07-40-02-500-004-A01
A. Preparation
(1) If possible, do an EIS star procedure, see AMM 31-60-00-860-001.
(2) On the N/W steering deactivation electrical-box 5GC:
(a) Set the ground-towing control lever to the towing position.
(b) Install the D23156000 PIN-SAFETY.
Subtask 07-40-02-020-001-A01
B. Removal of Components for Access
(1) See FIGURE 07-40-02-991-004-A.
(2) Remove the nuts (1), the washers (2) and the bolts (3).
(3) Remove the block (4).
(4) Remove the split pin (7), nut (6) and washer (5).
(5) Remove the bolt (9) and sleeve (8).
(6) Disconnect the rod end of the lower slave link sub-assembly (10).
07-40-02Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 07-40-02-500-006-A01
C. Installation of the Towing Attachment
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE CORRECTLYINSTALLED ON THE LANDING GEAR. THIS PREVENTS UNWANTEDMOVEMENT OF THE LANDING GEAR.
WARNING : MAKE SURE THAT NO PERSONS ARE NEAR THE TOWING CABLES WHENTHE TRACTOR APPLIES TENSION TO THE CABLES. DEATH OR INJURYCAN OCCUR IF A CABLE BREAKS.
(1) Install the 98D09104001000 ATTACHEMENT-TOWING (see FIGURE 07-40-02-991-005-A) or 98D09104002000 ATTACHMENT - TOWING (OPTIONAL 4 WHEEL BOGIE MLG)(see FIGURE 07-40-02-991-006-A) on each MLG.
(2) Install the 98A09003500000 CABLE-TOWING, MLG on the towing attachments.
(3) Connect the 98A09003500000 CABLE-TOWING, MLG to the tractor.
NOTE : Airbus recommends that you install bridge cables or ropes between the towingcables to prevent unwanted cable movement if a cable breaks.
WARNING : BE CAREFUL WHEN YOU USE THE NOSE WHEEL STEERING-BAR DURINGTOWING OF THE AIRCRAFT. THERE IS A RISK OF INJURY IF SUDDENUNWANTED MOVEMENT OF THE AIRCRAFT OR STEERING BAR OCCURS.
(4) Install the 98A09003000001 BAR-STEERING, NOSE WHEEL on the NLG, see FIGURE07-40-02-991-007-A.
Subtask 07-40-02-584-002-A01
D. Towing
WARNING : DURING TOWING / TAXIING OPERATION (LOW-SPEED OPERATIONINCLUDED), EACH PERSON IN THE AIRCRAFT MUST BE IN A SEAT ANDTHE SEAT BELT MUST BE FASTENED. IF THE SEAT BELT IS NOTFASTENED, THERE IS A RISK OF INJURY IF THE AIRCRAFT STOPSSUDDENLY.
WARNING : MAKE SURE THAT NO PERSONS ARE NEAR THE TOWING CABLES WHENTHE TRACTOR APPLIES TENSION TO THE CABLES. DEATH OR INJURYCAN OCCUR IF A CABLE BREAKS.
WARNING : BE CAREFUL WHEN YOU USE THE NOSE WHEEL STEERING-BAR DURINGTOWING OF THE AIRCRAFT. THERE IS A RISK OF INJURY IF SUDDENUNWANTED MOVEMENT OF THE AIRCRAFT OR STEERING BAR OCCURS.
07-40-02Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
CAUTION : PUT THE PARKING BRAKE CONTROL SWITCH IN THE OFF POSITIONBEFORE YOU TOW OR PUSH BACK THE AIRCRAFT. THIS IS TOPREVENT HIGH LOADS WHICH CAN CAUSE DAMAGE TO THE NOSELANDING GEAR.
(1) Tow the aircraft slowly and smoothly.During the towing, put:- one person in the cockpit to operate the brakes if necessary,- two persons to monitor the wing tips.
(2) Where possible, keep the tractor aligned with the aircraft centerline. The maximum lateralposition that is permitted is the width of the aircraft.
NOTE : Airbus recommend that you install load cells on the towing cable to record andmonitor the loads applied on the MLG during the towing.
Subtask 07-40-02-869-002-A01
E. Close-up
(1) Visual Inspection
(a) After you complete the towing operation, make sure that the nose wheels are alignedwith the aircraft centerline.
(2) Aircraft Configuration
(a) Put the wheel chocks in position in front of and behind the wheels.
(b) On the panel 110VU, set the PARKING BRK control switch to ON.
(c) On the panel 400VU, make sure that the pressure indication on the yellow brake-pressure triple-indicator is correct: 3000 psi (206.84 bar). The pointer must be in thegreen area. The pointer must be in the green range.If necessary, pressurize the yellow hydraulic system, see AMM 29-24-00-863-001.
(3) Removal of the Tooling
(a) Remove the 98A09003000001 BAR-STEERING, NOSE WHEEL.
(b) Remove the towing cable.
(c) Remove the towing attachment of the towing strap from each MLG.
(d) Remove the tow-lever safety pin.
(e) Set the ground-towing lever to its initial position.
Subtask 07-40-02-500-007-A01
F. Install Components
(1) Put the rod end of the lower slave link sub-assembly (10) in position.See FIGURE 07-40-02-991-004-A.
07-40-02Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 05-047 ANTI CORROSIONCOMPOUND (HIGH TEMPERATURE SILICONE SEALANT). OBEY THEMATERIAL MANUFACTURER’S INSTRUCTIONS.
(2) Apply Material No. 05-047 Anti Corrosion Compound (High Temperature Silicone Sealant)on the plain shank of the bolt (9).
(3) Install the bolt (9), the sleeve (8), the washer (5) and the nut (6). Torque the nut (6) tobetween 2.1 and 2.7 m.daN (15.48 and 19.91 lbf.ft).
(4) Install the new split (7).
(5) Make sure that the lower slave link sub-assembly (10) is free to turn around the bolt (9).
WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 09-016 CORROSIONINHIBITING FILLET CONSISTENCY. OBEY THE MATERIALMANUFACTURER’S INSTRUCTIONS.
(6) Apply Material No. 09-016 Corrosion Inhibiting Fillet Consistency on the bolt (9) and nut(6).
(7) Put the block (4) in position on the flexible hoses and loosely install bolts (3), the washers(2) and the nuts (1).
(8) Make sure that the dimension ”Y” is 150 mm (5.91 in).
(9) Torque the nuts (1) to between 0.4 and 0.45 m.daN (35.39 and 39.82 lbf.in).
07-40-02Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
1 2
3
A
YB
A
B
9
8
7
65
N_AR_074002_1_0040102_01_00
10
Towing with MLG from the RearRemoval of Lower Slave Link
FIGURE-07-40-02-991-004-A01
07-40-02Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
A
TOWING CABLE
N_AR_074002_1_0050101_01_00
A
Towing with MLG from the RearTowing Attachment Tool - Two Wheel MLG
FIGURE-07-40-02-991-005-A01
07-40-02Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TOWINGCABLE
TOWINGATTACHMENT
A
N_AR_074002_1_0060101_01_00
A
Towing with MLG from the RearTowing Attachment Tool - Four Wheel Bogie MLG (Optional A320 Only)
FIGURE-07-40-02-991-006-A01
07-40-02Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_074002_1_0070101_01_00
A
A
Towing with MLG from the RearManual Steering Bar
FIGURE-07-40-02-991-007-A01
07-40-02Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-40-03 TOWING WITH DEFLATED TIRES
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 07-40-03-584-801-A01
Towing with Deflated Tires
1. GeneralThis procedure gives details and limitations to tow the aircraft when one or more tires are deflated.
2. InspectionsNot Applicable
3. Job Setup ReferencesThe steering angle must be kept to a limit when you tow the aircraft with one or more tires deflatedon one or more landing gears.- For aircraft equipped with the twin wheel MLG, see SUBTASK 07-40-03-584-001-A01,- For aircraft equipped with the optional four wheel bogie MLG (A320 only), see SUBTASK
07-40-03-584-002-A01.
4. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATIONTASK 07-40-01-584-801-A01 TASK 07-40-01-584-801-A01-Towing with the NLG with a
TowbarTASK 07-40-02-584-801-A01 TASK 07-40-02-584-801-A01-Towing with the Main Gear from
the Front
Referenced Information
TABLE 1
5. Procedure
Subtask 07-40-03-584-001-A01
A. Twin Wheel Main Landing Gear
(1) One tire is deflated on one or more gears (a maximums of three deflated tires).- Tow by the nose gear, see TASK 07-40-01-584-801-A01. The maximum permitted
lateral angle of the towbar is plus or minus 10 degrees.
(2) One tire is deflated on one main gear.- Tow by the nose gear, see TASK 07-40-01-584-801-A01. The maximum permitted
lateral angle of the towbar is plus or minus 40 degrees.
(3) Two tires are deflated on the same gear.- Tow by the main gear only, see TASK 07-40-02-584-801-A01.- The towbar must not move laterally at all.
07-40-03Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Subtask 07-40-03-584-002-A01
B. Optional Four Wheel Bogie Main Landing Gear (A320 only)
(1) One tire is deflated on one or more gears (a maximum of three deflated tires).- Tow by the nose gear, see TASK 07-40-01-584-801-A01. The maximum permitted
lateral angle of the towbar is plus or minus 10 degrees.
(2) One tire or two tires (one on each axle) deflated on one main gear.- Tow by the nose gear, see TASK 07-40-01-584-801-A01. The maximum permitted
lateral angle of the towbar is plus or minus 40 degrees.
(3) Two tires on the same axle or more than two tires deflated on the same gear (with the twotires on the NLG inflated).- Tow by the main gears, see TASK 07-40-02-584-801-A01.- Steer by the NLG with the towbar or the normal steering control, see TASK
07-40-01-584-801-A01.
(a) Two tires on the same axle or three tires deflated on the same gear.- The maximum permitted steering angle of the NLG is plus or minus 50 degrees.
(b) All the four tires are deflated on the same MLG.- The towbar must not move laterally at all.- The speed must be kept to a limit of approximately 1.3 m/s (4.27 ft/s).
07-40-03Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-40-04 TOWING LOAD LIMITS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-40-04-001-A01
Load and Angle Limits
1. Towing
WARNING : OBEY THE SAFETY PRECAUTIONS DURING TOWING OR MOVEMENT OF THEAIRCRAFT. MAKE SURE THAT THE PATH OF THE AIRCRAFT IS CLEAR. MAKESURE THAT NO PERSONS SIT OR STAND ON THE TOW BAR OR USE THETRACTOR AS TRANSPORT, THIS IS TO PREVENT THE RISK OF INJURY.
WARNING : DURING TOWING / TAXIING OPERATION (LOW-SPEED OPERATIONINCLUDED), EACH PERSON IN THE AIRCRAFT MUST BE IN A SEAT AND THESEAT BELT MUST BE FASTENED. IF THE SEAT BELT IS NOT FASTENED,THERE IS A RISK OF INJURY IF THE AIRCRAFT STOPS SUDDENLY.
CAUTION : DO NOT TOW OR MOVE THE AIRCRAFT ON THE GROUND IF THE ENGINECOWLS ARE OPEN.MOVEMENT OF THE AIRCRAFT WITH THE COWLS OPEN CAN CAUSEDAMAGE TO THE COWLS AND THE NACELLE STRUCTURE.
It is recommended that you use a towbar with a damping system.
A. You can use the NLG towbar fitting to tow or push the aircraft:- with maximum weight,- with the engines between zero and idle.
B. You can use the MLG attachments to tow the aircraft:- with the engines stopped,- when it is bogged.
C. Do not tow the aircraft if the dimension H is more than 300 mm (11.8110 in), see FIGURE07-40-04-991-001-A). If you do so, you can cause damage to the cams that make the nose gearwheels go back to the center position.
D. Keep a minimum of 3 m (9.84 ft) separation from the nose wheels, towbar and tractor while theaircraft moves.
2. Speed LimitsThe maximum permitted towing speed changes with the aircraft configuration.
A. Doors closed and locked or removed:
(1) For a tractor with a towbar, a maximum speed of 25 km/h (15.5 mph) is permitted.
(2) For a towbarless tractor, a maximum speed of 32 km/h (19.9 mph) is permitted.
07-40-04Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
B. Passenger/crew doors fully open and locked and/or cargo doors open in vertical position:
(1) The maximum permitted speed is 10 km/h (6.2 mph).
C. In wind conditions, calculate the permitted towing speed before towing:
(1) Measure the wind speed.
(2) Do a check of aircraft stability, see TBD or AMM 05-57-00-200-001.
(3) Substract measured wind speed from wind speed limit shown on the stability curve. Thisgives the maximum permitted towing speed.
3. Approximate Towing LoadsSee FIGURE 07-40-04-991-002-A.
NOTE : In all the formulas, MTW = Maximum Taxi Weight.
A. When you push the aircraft rearward with the engines at idles, you must add the engine thrustresistance to the towing loads.
NOTE : The engine thrust resistance at ground idle is 400 daN (for each engine in operation).
B. Use these coefficients for the friction between the tires of the tow tractor and the ground tocalculate the tractor weight:- Dry concrete or asphalt: 0.80- Wet asphalt: 0.75- Wet asphalt: 0.57- Hard snow: 0.20- Ice: 0.05Minimum Tractor Weigh = 6% MTW / (friction coefficient)
**ON A/C A318-100 A319-100 A320-100 A320-200
4. Limit Loads and AnglesSee FIGURE 07-40-04-991-003-A.
A. In all the towing configurations, the safety pin locks the control lever on the interphone box inthe disengaged position.
B. The maximum permitted steering angle on each side of the aircraft centerline is:- +/- 95 degrees with towbar,- +/- 85 degrees without towbar.
C. During towing, the towing angle must not be more that then angle shown on the FWD NLGdoors.
D. Tow the aircraft (slowly and smoothly) with the main landing gear:- The maximum towing angle in the vertical plane is 11 degrees.- The NLG gives the limits for the maximum towing angle in the horizontal plane.
07-40-04Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
E. Use a towbar with:- The towing shear pins, calibration 9425 daN (21188.24 lbf) for the protection of the landing
gear against too high loads,- The safety shear pin, calibration 826 m.daN (6091.44 lbf.ft) for the protection of the
landing gear against to high torsion.
F. Use:- The tow special fork fitting and a cable to tow the main landing gear forward or rearward.
Attach these special fork fittings to the lugs at each end of the landing gear.- The safety shear pin, calibration 29000 daN (65194.58 lbf) which comes with the two-
fitting/cable net.
**ON A/C A321-100 A321-200
5. Limit Loads and AnglesSee FIGURE 07-40-04-991-003-A.
A. In all the towing configurations, the safety pin locks the control lever on the interphone box inthe disengaged position.
B. The maximum permitted steering angle on each side of the aircraft centerline is:- +/- 95 degrees with towbar,- +/- 85 degrees without towbar.
C. During towing, the towing angle must not be more that then angle shown on the FWD NLGdoors.
D. Tow the aircraft (slowly and smoothly) with the main landing gear:- The maximum towing angle in the vertical plane is 4 degrees.- The NLG gives the limits for the maximum towing angle in the horizontal plane.
E. Use a towbar with:- The towing shear pins, calibration 9425 daN (21188.24 lbf) for the protection of the landing
gear against too high loads,- The safety shear pin, calibration 826 m.daN (6091.44 lbf.ft) for the protection of the
landing gear against to high torsion.
F. Use:- The tow special fork fitting and a cable to tow the main landing gear forward or rearward.
Attach these special fork fittings to the lugs at each end of the landing gear.- The safety shear pin, calibration 29000 daN (65194.58 lbf) which comes with the two-
fitting/cable net.
07-40-04Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_074004_1_0010101_01_00
H
Towing LimitsMaximum Extension of the NLG Shock Absorber
FIGURE-07-40-04-991-001-A01
07-40-04Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_074004_1_0020101_01_00
TOWING FORCES
BREAKAWAY
ROLLING
BREAKAWAYON SLOPE
ON SLOPEROLLING
F
6% MTW
3% MTW
6% MTW+ 1% MTW PER
1% SLOPE
+ 1% MTW PER1% SLOPE
3% MTW
Towing LimitsTowing Forces
FIGURE-07-40-04-991-002-A01
07-40-04Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
GEAR LOADS
A
B 29000
9425daN
65200
21188lbf
BB
BB
A
A
MAXIMUM
MAX ANGLEWITH TOWBAR = 95° MAX ANGLE WITH
TOWBARLESS = 85°
N_AR_074004_1_0030101_01_01
Towing LimitsTowing Loads and Angles
FIGURE-07-40-04-991-003-A01
07-40-04Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-60-00 MOVING DAMAGED AIRCRAFT
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-60-00-001-A01
General
1. This section describes the moving of aircraft with damaged or missing landing gear.If it is possible, the aircraft must always be moved the landing gear supporting the weight of theaircraft.Before moving the aircraft, you must verify the structural integrity of the landing gear and thestructural attachments in accordance with the landing gear inspection procedure 02-30-01.For landing gears that are not correctly extended, see TBD for information on the manual extensionof the landing gear.If any of the landing gear are damaged, you must always try to repair or replace the damaged landinggear. This could include:- The repair of the existing landing gear,- The installation of a replacement landing gear,- The temporary bracing of the landing gear to support the weight of the aircraft.The repair or replacement of damaged landing gear is the recommended solution if a replacementlanding gear is available and the structural attachments for the landing gear are not damaged.If it is not possible to move the aircraft using it’s landing gears, then you must use a different supportsystem to move the aircraft, see 07-60-03. It may be necessary to use one of the following vehicles ora combination of vehicles to move the aircraft.- Flat bed trailers,- Movable cranes,- Specialist aircraft recovery transportation systems,- General purpose trucks,- Commercial transport equipment.Moving the aircraft using aircraft recovery vehicles must be the last method to be used after all othermethods have been analyzed. When aircraft recovery transport vehicles are used, secondary damage ispossible.
07-60-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-60-01 MOVING DAMAGED AIRCRAFT ON TRAILERS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-60-01-001-A01
Moving Damaged Aircraft on Trailers
1. If the Landing Gear cannot be made serviceable, the use of trailers gives a safe and correct method ofsupporting the aircraft fuselage and/or the wings.
WARNING : MAKE SURE THAT THE TRAILERS, AND ALL OTHER EQUIPMENT YOU USEWITH THE TRAILERS, ARE SAFE FOR THE WEIGHT THEY MUST SUPPORT.
CAUTION : BE CAREFUL WHEN YOU USE SUPPORTS. MAKE SURE THAT THE LOADS ONTHE AIRFRAME ARE LESS THAN THE ALLOWABLE LOADS (SKIN LOADINGLIMITS) WHEN YOU USE SUPPORTS. THE SUPPORTS APPLY LOADS THATDO NOT OCCUR IN NORMAL OPERATION.
CAUTION : SECONDARY DAMAGE CAN OCCUR WHEN YOU USE TRAILERS TO SUPPORTAND MOVE THE AIRCRAFT.
CAUTION : DO NOT APPLY LOADS TO THE ENGINE NACELLE STRUCTURE BECAUSESECONDARY DAMAGE WILL OCCUR.
CAUTION : DO NOT APPLY LOADS TO THE FLAP-TRACK FAIRING STRUCTUE BECAUSESECONDARY DAMAGE WILL OCCUR
A. See 06-40-00 for the bearing area under the fuselage and wings.
B. You must inspect the aircraft structure for damage in the bearing areas. Make sure that thestructure is capable of supporting the weight of the aircraft on the trailers.
C. You can support the forward fuselage on a turntable, this will help to turn the aircraft duringthe move. If a turntable is used, it must conform to the weight requirements and general aircraftspecifications to prevent secondary damage and assist in the removal of the aircraft.
D. Install supports between the aircraft and the trailer surface. These can be made of timber andmust be covered with padded material to avoid damage to the aircraft surfaces. The supportsthat you use must be able to support the expected loading.
E. Materials such as mattresses, rubber padding, tires, pneumatic bags and sand bags can be usedas padding. It is important that the padding is arranged to follow the contour of the aircraftsurfaces, this will helps to spread the loads on the surface and to avoid point loads. Filler foamcan be used at the support areas to fill gaps and make a correct contoured support.You must not exceed the allowable skin loading limits on the aircraft surfaces, see 06-40-00.
F. It is important that the supports (timber) and padding remain stable while you move theaircraft. It may also be necessary to tie down the aircraft structure to the trailer to preventrelative movement between the aircraft and the trailer.
07-60-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
G. Some aircraft recovery trailers have hydraulically controlled supports, that conform to thefuselage and wing contours.
H. Monitor the loads during all the moving operation.
07-60-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_076001_1_0020101_01_00
NOSE TRAILERWITH ADJUSTABLE
TURNTABLE
HYDRAULIC PLATFORMBOGIES FOR SMALLER
LOADS
CABLE AND CHAINCONNECTION
SOME TRAILERSHAVE HYDRAULICALLY
CONTROLLED SUPPORTS
MAXIMUM15 DEGREE TILT
Moving Damaged Aircraft on TrailersConfiguration of Trailers
FIGURE-07-60-01-991-002-A01
07-60-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
PA
DD
ING
MA
TE
RIA
LS(P
LYW
OO
D, P
NE
UN
AT
IC L
IFT
ING
BA
GS
, TIR
ES
, ET
C)
TIE
DO
WN
ST
RA
PF
LAT
BE
D T
RA
ILE
R
TY
PIC
AL
TU
RN
TA
BLE
FLA
TB
ED
TR
AIL
ER
N_A
R_0
7600
1_1_
0030
101_
01_0
0
Moving Damaged Aircraft on TrailersTypical Use of Trailers with Aircraft
FIGURE-07-60-01-991-003-A01
07-60-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-60-02 MOVING DAMAGED AIRCRAFT WITH CRANES
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-60-02-001-A01
Moving Damaged Aircraft with Cranes
1. General
CAUTION : IF THE LOADS APPLIED DURING THE RECOVERY PROCEDURE ARE MORETHAN THE MAXIMUM ALLOWABLE LOADS, YOU MUST CONTACT AIRBUSFOR SPECIFIC INSPECTIONS.
CAUTION : BE CAREFUL WHEN YOU USE SUPPORTS. MAKE SURE THAT THE LOADS ONTHE AIRFRAME ARE LESS THAN THE ALLOWABLE LOADS (SKIN LOADINGLIMITS) WHEN YOU USE SUPPORTS. THE SUPPORTS APPLY LOADS THATDO NOT OCCUR IN NORMAL OPERATION.
CAUTION : USE ONLY RECOVERY SLINGS AND SPREADER BEAMS SPECIFIED BY AIRBUS.NON-APPROVED LIFTING DEVICES CAN CAUSE SECONDARY DAMAGE TOTHE AIRCRAFT.
CAUTION : MAKE SURE THAT THE CRANE YOU USE CAN LIFT THE ESTIMATED LOADPLUS THE WEIGHT OF THE LIFTING EQUIPMENT BEFORE YOU START TOLIFT THE AIRCRAFT.
CAUTION : MAKE SURE THAT THE LOADS ON THE AIRFRAME ARE LESS THAN THEALLOWABLE LOADS WHEN YOU USE SUPPORTS. THE SUPPORTS APPLYLOADS THAT DO NOT OCCUR IN NORMAL OPERATION.
The principles outlined in this chapter are provided as a guide to assist an aircraft recovery.See 06-50-00 for information on the use of cranes.If it is possible, damaged landing gears must be repaired or replaced. This will allow the aircraft to bemoved with it’s own landing gear supporting the weight of the aircraft.If it is not possible to repair or replace the damaged landing gear, an alternative method is to usemobile crane or crawler crane to help move the aircraft.
NOTE : You must analyze other methods of supporting and moving the aircraft before using thismethod.
If the aircraft is in this condition, then it is possible to use cranes and sling assembly to level and liftthe aircraft. The cranes can then be left in place to support and move the aircraft.Roadways must be properly prepared to support the weight of the crane and the aircraft as they aremoved, see 07-20-00.
2. Moving the Aircraft with CranesThe crane must be positioned close enough to the aircraft and the lifting point, to let the crane useits lifting capacity safely.
07-60-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
A. You must monitor and record the loads on the slings when you use this process.
B. The moveable cranes must begin to move at the same time, and must move steadily at thesame speed during the entire aircraft movement operation.
C. The person controlling the operation must be in constant contact with the cranedrivers/operators.
D. See 06-50-00 for tooling specification, procedures and limitations to level/lift the aircraft usingcranes.
07-60-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
07-60-03 MOVING DAMAGED AIRCRAFT WITH SPECIALIZED EQUIPMENT
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 07-60-03-001-A01
Moving Damaged Aircraft with Specialized Vehicles
1. Specialized recovery vehicles include sledges and patent trailer systems made by differentmanufacturers.
CAUTION : DO NOT APPLY LOADS OUT OF THE ALLOWABLE LIMITS BECAUSESECONDARY DAMAGE WILL OCCUR
CAUTION : DO NOT APPLY LOADS TO THE ENGINE NACELLE STRUCTURE BECAUSESECONDARY DAMAGE WILL OCCUR.
A. The sledge systems are simple systems that are used to support the aircraft while it is towed onsoft ground.
B. The patent trailer systems are complex systems and can be used to move damaged aircraft thathas no serviceable landing gear, see 07-60-01.This type of trailer normally:- Has hydraulically controlled supports that can conform to the fuselage and wing contours.- Has a multi-wheel steering function.- Can be linked with beams or cables to other trailers.
07-60-03Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
POST RECOVERY CORRECTIVE ACTIONS
08-00-00 POST RECOVERY CORRECTIVE ACTIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 08-00-00-001-A01
General
1. RecordsAirbus recommends that you make records on the full recovery operation.These records can help you:- To make aircraft maintenance operations easier for the return to service- To have a feedback of the recovery operation- To have traceability after the recovery.The records can include:- The aircraft inspection report- Results of loads and CG calculations- The technique used to level/lift and move the aircraft- Loads applied during the recovery operation- ...
2. Post Recovery InspectionsIf necessary, do the ”Inspection After Leaving Runway or Taxiway”, see AMM 05-51-24-200-001.
08-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
APPENDIX
09-00-00 APPENDIX
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-00-00-001-A01
Introduction
1. This chapter has the structure that follows:
A. General Information (09-10)
(1) General charts and formulae for metric and imperial measurement conversion.
(2) Definitions related to aircraft recovery (glossary).
(3) General aircraft dimensions, fuselage, wing and horizontal stabilizer stations, frames andribs, door sizes, ground clearances, ground service connections illustrations, etc.).
B. Recovery Preparation (09-20)
(1) Guides or planning charts not related to the aircraft type.
(2) Possible composition of the recovery team.
C. Tooling and Equipment (09-30)
(1) General aircraft recovery materials and equipment.
(2) Specific aircraft tooling and aircraft recovery kits.
(3) Aircraft Recovery Kits.
D. Calculation Worksheets (09-50)
(1) Weight and balance calculation worksheets.
09-00-00Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-01 UNITS AND CONVERSIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-01-002-A01
Units of Measurements
1. This topic gives the ISO and NON-ISO units used in this manual.
meters (m)Length
millimeters (mm)
Area square meters (m2)
Volume cubic meters (m3)
Weight kilograms (kg)
kilograms per cubic meter (kg/m3)Density
kilograms per liter (kg/l)
Force Newtons (N)
Newton-meters (N.m)Moment
product of weight and length in kilogram-meters (kgm)
Pascals (Pa)Pressure
bars (bar)
meters per second (m/s)Velocity
kilometers per hour (km/h)
Capacity and Quantity liters (l)
Temperature degrees Celsius (˚C)
radians (rad)Angle
degrees (˚)
ISO and Derived Measurement System
TABLE 1
feet (ft)Length
inches (in)
Area square feet (ft2)
Volume cubic feet (ft3)
Weight pounds (lb)
pounds per cubic foot (lb/ft3)Density
pounds per US gallon (lb/US gal)
09-10-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Force pound-force (lbf)
pound-force feet (lbf.ft)Moment
product of weight and length in pounds-inches (lb.in)
Pressure pounds per square inch (psi)
feet per seconds (ft/s)Velocity
miles per hour (mph)
Capacity and Quantity US gallons (US gal)
Temperature degrees Fahrenheit (˚F)
radians (rad)Angle
degrees (˚)
US Customary System
TABLE 2
09-10-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-01-001-A01
Conversion Tables
1. This topic gives the conversion values to use for the conversion of units.
MULTIPLY BY TO OBTAIN
Meters (m)Meters (m)Millimeters (mm)Millimeters (mm)
39.370083.2808400.039370080.00328084
Inches (in)Feet (ft)Inches (in)Feet (ft)
LengthInches (in)Inches (in)Feet (ft)Feet (ft)
0.025425.40.3048304.8
Meters (m)Millimeters (mm)Meters (m)Millimeters (mm)
Square meters (m2) 10.763910 Square feet (ft2)Area
Square feet (ft2) 0.09290304 Square meters (m2)
Cubic meters (m3) 35.31466 Cubic feet (ft3)Volume
Cubic feet (ft3) 0.02831685 Cubic meters (m3)
Kilograms (kg) 2.204622 Pounds (lb)Weight
Pounds (lb) 0.4535924 Kilograms (kg)
Kilograms per liter (kg/l)Kilograms per liter (kg/l)Kilograms per cubic meter (kg/m3)Kilograms per cubic meter (kg/m3)
62.427978.34564590.062427970.0083457
Pounds per cubic foot (lb. ft3)Pounds per US gallon (lb/US gal)Pounds per cubic foot (lb. ft3)
Pounds per US gallon (lb/US gal)Density
Pounds per cubic foot (lb. ft3)Pounds per cubic foot (lb. ft3)Pounds per US gallon (lb/US gal)Pounds per US gallon (lb/US gal)
0.01601846316.0184630.119823119.8225188
Kilograms per liter (kg/l)Kilograms per cubic meter (kg/m3)Kilograms per liter (kg/l)Kilograms per cubic meter (kg/m3)
Newtons (N) 0.2248089 Pound-forces (lbf)
Pound-forces (lbf) 4.448222 Newtons (N)Force
Newtons (N)Decanewtons (daN)
100.1
Decanewtons (daN)Newtons (N)
Newton-meters (N.m) 0.7375621 Pound-force feet (lbf.ft)
Pound-force feet (lbf.ft) 1.355818 Newton-meters (N.m)Moment
Newton-meters (N.m)Decanewton-meters (daN.m)
100.1
Decanewton-meters (daN.m)Newton-meters (N.m)
09-10-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
MULTIPLY BY TO OBTAIN
Pascals (Pa)Bars (bar)
0.000145037714.50377
Pounds per square inch (psi)Pounds per square inch (psi)
PressurePounds per square inch (psi)Pounds per square inch (psi)
6894.7570.06894757
Pascals (Pa)Bars (bar)
Meters per second (m/s)Meters per second (m/s)Kilometers per hour (km/h)Kilometers per hour (km/h)
3.28083992.23690.91130.6214
Feet per second (ft/s)Miles per hour (mph)Feet per second (ft/s)Miles per hour (mph)
Feet per second (ft/s)Feet per second (ft/s)Miles per hour (mph)Miles per hour (mph)
0.30481.09730.44701.6093
Meters per second (m/s)Kilometers per hour (km/h)Meters per second (m/s)Kilometers per hour (km/h)
Knots (kt)Kilometers per hour (km/h)
1.8520.5399568
Kilometers per hour (km/h)Knots (kt)
Velocity
Knots (kt)Miles per hour (mph)
1.1500.86897
Miles per hour (mph)Knots (kt)
Liters (l) 0.264172 US gallons (US gal)CapacityQuantity US gallons (US gal) 3.785412 Liters (l)
Conversion Table
TABLE 1
Temperature conversion:- Temperature conversion from degrees Celsius (˚C) to degrees Fahrenheit (˚F):
˚F = 1.8 × ˚C + 32- Temperature conversion from degrees Fahrenheit (˚F) to degrees Celsius (˚C):
˚C = 0.5555 × (˚F - 32)
09-10-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-02 GLOSSARY OF TERMS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-02-001-A01
Definition of Terms
1. GeneralThe terms that follow are used in the ARM.
A. Aircraft RecoveryAn aircraft recovery operation is the action of moving any aircraft that is disabled and unable tomove with its power or with the standard use of a correct tow tractor and standard tow bar,but can be economically repairable.Examples of aircraft recovery incidents are:- One or more landing gears off the hard surface of a runway, taxiway or apron,- Aircraft bogged down in mud, snow or sand,- One or more landing gears retracted, collapsed, damaged, or missing.
B. Warnings, Cautions and NotesThese definition of these are as follow:- WARNING: Calls attention to the use of materials, processes, methods, procedures or limits
that must be obeyed to prevent injury or death to persons.- CAUTION: Calls attention to methods and procedures that must be obeyed to prevent
damage to equipment.- NOTE: Calls attention to methods that make the job easier or give more information.
2. Weight Terms
A. Manufacturer Empty Weight (MEW)The weight of the structure, power plant, systems, furnishings and other items of equipment,part of a special aircraft configuration, with the fluids in closed systems (e.g. hydraulic fluid).The weights of all operator items are not included.
B. Operator ItemsThese items include:- Unusable fuel,- Oil for engines, IDG and APU,- Water for galleys and lavatories,- Chemical fluids for waste tanks,- Aircraft documents and tool kits,- Passenger seats and life vests,- Galley structures and fixed equipment,- Catering,- Flight and cabin crew and their baggage,- Emergency equipment that includes:
09-10-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Evacuation aids, life rafts, portable oxygen bottles and stowage boxes, extinguishers,megaphones, flash lights, axes, first aid kits, emergency radio beacons, fire resistant glovesand smoke goggles, demonstration kits, life vests for crew and children.
C. Operational Empty Weight (OEW)The OEW is the sum of the Manufacturer Empty Weight plus the operator items.
D. Dry Operating Weight (DOW)The DOW is the total weight of an aircraft prepared for a special type of operation without allthe usable fuel and traffic load.It is the sum of the OEW and the special items for the type of flight (e.g. catering, newspapers,pantry equipment etc.).
E. Recoverable Empty Weight (REW)The REW is the sum of the MEW and the weight of the different operator items which are partof the aircraft. The REW does not include the crew and their baggage or catering equipmentand supplies.
F. Net Recoverable Weight (NRW)The NRW is the REW of the aircraft without the missing or removed aircraft equipment andcomponents. It includes fuel, liquids and cargo remaining on board.The applicable recovery scenario is based on the NRW.
G. Payload (P/L)The payload is the weight of the passengers, cargo and baggage.
H. Center of Gravity (CG)The CG is the point where the aircraft can balance if it hangs at that point. It is the pointwhere the aircraft weight is applied.If more weight is put in a different point, it causes an unbalancing force which is the ”moment”.In case of recovery action, the position of CG has to stay within certain predefined limits toensure aircraft general stability
J. Reference Chord (RC) or Mean Aerodynamic Chord (MAC)Usually the position of the CG is defined by a percentage of Reference Chord (%RC).The Reference Chord is a reference line used in the design of the wing. Its position relative tothe wing and fuselage is accurately known. It represents the variation of position of the CG,according to the weight and balance management or other parameters. The normal position ofthe CG is considered at 25%RC. The position and dimensions of this reference are mentioned inTASK 03-00-00-558-801-A01. These dimensions are specially dedicated to an aircraft type.
K. Maximum Design Landing Weight (MLW)The MLW is the maximum permitted weight at which the aircraft can land.
L. Maximum Ramp Weight (MRW) / Maximum Taxi Weight (MTW)The MRW / MTW is the maximum permitted weight for ground maneuvers, that include taxiand run-up fuel.
09-10-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
M. Maximum Takeoff Weight (MTOW)The MTOW is the maximum permitted weight when the brakes are released for takeoff, or atthe start of the takeoff roll.
N. Maximum Zero Fuel Weight (MZFW)The MZFW is the maximum operating weight without usable fuel.
P. Actual Zero Fuel Weight (AZFW)The AZFW is the sum of the operational empty weight and payload.The AZFW must never be more the maximum design zero fuel weight (MZFW).
Q. Engineered LiftingAn engineered lifting is a lifting of the aircraft in controlled conditions, with a predefined processusing specific GSE. Before this procedure is started, it is necessary to do:- An accurate analysis of the requirements- An accurate engineering planning and a risk/hazard assessment- A lifting procedure approved by the local authority regulations.
09-10-02Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-02-003-A01
Abbreviations
1. List of AbbreviationsThe abbreviations that follow are used in the ARM.
A/C Aircraft
AC Aircraft Characteristics for Airport Planning
AD Aircraft DatumAFRP Aramid Fiber Reinforced PlasticAMM Aircraft Maintenance ManualAPU Auxiliary Power Unit
ARM Aircraft Recovery Manual
ARWG Aircraft Recovery Working Group
ATA Air Transport Association of America
AZFW Actual Zero Fuel Weight
CBR California Bearing Ratio
CFRP Carbon Fiber Reinforced PlasticCG Center of Gravity
CL Center LineCLS Cargo Loading System
CLSM Cargo Loading System Manual
CRC Crew Rest Compartment
CTR CenterDBP Drawbar PullDOW Dry Operating Weight
ECAM Electronic Centralized Aircraft Monitoring
EIS Electronic Instrument System
EWH External Wiring Harness
FDL Fuselage Datum Line
FQI Fuel Quantity Indicator
FR FrameFWD ForwardGFRP Glass Fiber Reinforced PlasticGPU Ground Power UnitIATA International Air Transport Association
IATP International Airline Technical PoolICAO International Civil Aviation Organization
09-10-02Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
IDG Integrated Drive Generator
INBD InboardINR InnerIPC Illustrated Parts Catalog
L/G Landing Gear
LDG Landing
LDMCR Lower Deck Mobile Crew RestLGCIU Landing Gear Control and Interface Unit
LH Left HandLRE List of Radioactive and Hazardous Elements
ManualMCDU Multipurpose Control & Display Unit
MEW Manufacturer’s Empty Weight
MFP Maintenance Facility Planning Manual
MID MiddleMLG Main Landing Gear
MLW Maximum Design Landing Weight
MMI Manual Magnetic Indicator
MRW Maximum Ramp Weight
MSN Manufacturer’s Serial NumberMTOW Maximum Design Take Off Weight
MTW Maximum Taxi Weight
MZFW Maximum Design Zero Fuel Weight
NAS Navy and Army Standard
NLG Nose Landing Gear
NRW Net Recoverable Weight
NWS Nose Wheel Steering
OEW Operating Empty Weight
OUTBD Outboard
P/BSW Push Button Switch
P/L Payload
PAX Passenger
PSU Passenger Service Unit
RC Reference ChordRCT Rear Center TankREW Recoverable Empty Weight
RH Right Hand
SRM Structural Repair Manual
09-10-02Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
STA StationSTGR Stringer
T TrimTBD To Be Define / Determined
TBIL To Be Issued LaterTEM Illustrated Tool and Equipment Manual
THS Trimmable Horizontal StabilizerTK TankTPIS Tire Pressure Indicating System
ULD Unit Load DeviceW&B Weight and Balance
WBM Weight and Balance Manual
XFR Transfer
List of Abbreviations
TABLE 1
09-10-02Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-02-002-A01
Aircraft Reference Axes
1. DefinitionsSee FIGURE 09-10-02-991-001-A.
A. AD (Aircraft Datum)Vertical plane (equation Y=0). It is shown as a line on XY and YZ drawings.
B. FD (Fuselage Datum)Horizontal plane (equation Z=0). It is shown as a line (FDL) on XZ and YZ drawings.
C. Fuselage Datum Line (FDL)View of FD plan on 2D drawings (XZ and YZ planes).
D. Center Line (C/L)Intersection of AD and FD planes.
E. H-armHorizontal arm from X=0 in length unit.
F. Y-armLateral arm Y=0 in length unit.
G. Z-armVertical arm Z=0 in length unit.
09-10-02Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
+Z
0
+Y
AD
+X
7.000 m(275.59 in)
N_AR_091002_1_0010101_01_00
2.540 m(100 in)
Aircraft Reference AxesGeneral
FIGURE-09-10-02-991-001-A01
09-10-02Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-03 AIRCRAFT DIMENSIONS
**ON A/C A318-100
DESC 09-10-03-001-A01
General
1. This chapter gives the main dimensions of the A318 aircraft:- See FIGURE 09-10-03-991-001-A and FIGURE 09-10-03-991-002-A.
09-10-03Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
5.07 m
11.51 m
7.59 m
34.10 m
12.45 m
10.25 m
(37.76 ft)
(12.93 ft)
(16.63 ft) (32.62 ft)
(111.88 ft)
31.45 m(103.18 ft)
(40.85 ft)
30.96 m(101.57 ft)
6.62 m(21.72 ft)
NOTE: RELATED TO AIRCRAFT ATTITUDE AND WEIGHTN_AR_091003_1_0010101_01_01
Aircraft Dimensions - A318Side and Front View
FIGURE-09-10-03-991-001-A01
09-10-03Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
30.64 m(100.52 ft)
A
A = CFM56: 8.97 m (29.43 ft)PW6000: 8.85 m (29.0 ft)
N_AR_091003_1_0020101_01_01
Aircraft Dimensions - A318Top View
FIGURE-09-10-03-991-002-A01
09-10-03Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
DESC 09-10-03-001-B01
General
1. This chapter gives the main dimensions of the A319 aircraft:- See FIGURE 09-10-03-991-003-A and FIGURE 09-10-03-991-004-A.
09-10-03Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
12.45 m
5.07 m(16.63 ft)
11.04 m(36.22 ft)
34.10 m(111.88 ft)
(40.85 ft)
(12.93 ft)
(37.76 ft)
7.59 m
11.51 m
OPTIONAL
33.11 m(108.63 ft)
33.84 m(111.02 ft)
5.87 m(19.26 ft)
NOTE: RELATED TO AIRCRAFT ATTITUDE AND WEIGHTN_AR_091003_1_0030101_01_01
Aircraft Dimensions - A319Side and Front View
FIGURE-09-10-03-991-003-A01
09-10-03Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
33.024 m(108.35 ft)
A
A = CFM56: 9.76 m (32.02 ft)IAE V2500: 9.60 m (31.5 ft)
N_AR_091003_1_0040101_01_01
Aircraft Dimensions - A319Top View
FIGURE-09-10-03-991-004-A01
09-10-03Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
DESC 09-10-03-001-C01
General
1. This chapter gives the main dimensions of the A320 aircraft:- SeeFIGURE 09-10-03-991-005-AFIGURE 09-10-03-991-005-B and FIGURE 09-10-03-991-006-A.
09-10-03Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100
7.59 m(12.93 ft)
12.45 m(40.85 ft)
33.91 m(111.25 ft)
36.84 m(120.87 ft)
5.07 m(16.63 ft)
12.63 m(41.44 ft)
37.57 m(123.36 ft)
NOTE: RELATED TO AIRCRAFT ATTITUDE AND WEIGHT
5.87 m(19.26 ft)
11.51 m(37.76 ft)
N_AR_091003_1_0050101_01_01
Aircraft Dimensions - A320-100Side and Front View
FIGURE-09-10-03-991-005-A01
09-10-03Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-200
7.59 m(12.93 ft)
12.45 m(40.85 ft)
34.10 m(111.88 ft)
36.84 m(120.87 ft)
5.07 m(16.63 ft)
12.64 m(41.47 ft)
37.57 m(123.36 ft)
NOTE: RELATED TO AIRCRAFT ATTITUDE AND WEIGHT
11.51 m(37.76 ft)
5.87 m(19.26 ft)
N_AR_091003_1_0050201_01_01
Aircraft Dimensions - A320-200Side and Front View
FIGURE-09-10-03-991-005-B01
09-10-03Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
37.57 m(123.26 ft)
A = CFM56: 11.36 m (37.27 ft)IAE V2500: 11.20 m (36.75 ft)
A
N_AR_091003_1_0060101_01_01
Aircraft Dimensions - A320-100/-200Top View
FIGURE-09-10-03-991-006-A01
09-10-03Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
DESC 09-10-03-001-D01
General
1. This chapter gives the main dimensions of the A321 aircraft:- See FIGURE 09-10-03-991-007-A and FIGURE 09-10-03-991-008-A.
09-10-03Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
43.69 m(143.34 ft)
5.87 m(19.26 ft)
5.07 m(16.63 ft)
16.91 m(55.48 ft)
44.51 m(146.03 ft)
7.59 m(12.93 ft)11.51 m(37.76 ft)
12.45 m(40.85 ft)
34.10 m(111.88 ft)
NOTE: RELATED TO AIRCRAFT ATTITUDE AND WEIGHTN_AR_091003_1_0070101_01_01
Aircraft Dimensions - A321Side and Front View
FIGURE-09-10-03-991-007-A01
09-10-03Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
A
44.51 m(146.03 ft)
A = CFM56: 15.63 m (51.28 ft)IAE V2500: 15.47 m (50.75 ft)
N_AR_091003_1_0080101_01_01
Aircraft Dimensions - A321Top View
FIGURE-09-10-03-991-008-A01
09-10-03Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-04 AIRCRAFT STRUCTURAL SECTIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-04-001-A01
General
1. Sections and ComponentsFor the different structural sections and components of the aircraft see FIGURE 09-10-04-991-001-AFIGURE 09-10-04-991-001-BFIGURE 09-10-04-991-001-CFIGURE 09-10-04-991-001-D.
09-10-04Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
11/1
2
13/1
4
5121
41 42
5223 24
2229
28
27
2526
16/1
7
18
3132
19.1
36
1935
15
N_AR_091004_1_0010101_01_01
Aircraft Structural SectionsStructure Sections and Components - A318 (Sheet 1 of 2)
FIGURE-09-10-04-991-001-A01
09-10-04Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
SECTION DESIGNATION
11/12
REAR FUSELAGE
13/14
REAR FUSELAGE
15
CONE/REAR FUSELAGE
16/17
CONE/REAR FUSELAGE
18
CENTER WING
19
OUTER WING
19.1
LEADING EDGES
21
LEADING EDGES
22
SPOILERS
23
INBOARD FLAP
24
OUTBOARD FLAP
25
AILERON
26
WING−TIP
27
VERTICAL STABILIZER
28
RUDDER
29
HORIZONTAL STABILIZER
31
ELEVATOR
32
PYLONS
35
NACELLE SECTION
36
NOSE GEAR AND DOORS
41
MAIN GEAR AND DOORS
42
NOSE FORWARD FUSELAGE
51
FORWARD FUSELAGE
52
CENTER FUSELAGE
N_AR_091004_1_0010103_01_00
Aircraft Structural SectionsStructure Sections and Components - A318 (Sheet 2 of 2)
FIGURE-09-10-04-991-001-A01
09-10-04Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
11/1
2
13/1
4
51
5223 24
2229
28
27
2526
16/1
7
18
3132
19.1
36
1935
15
21
41 42
N_AR_091004_1_0010201_01_01
Aircraft Structural SectionsStructure Sections and Components - A319 (Sheet 1 of 2)
FIGURE-09-10-04-991-001-B01
09-10-04Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N_AR_091004_1_0010202_01_00
SECTION DESIGNATION
11/12
REAR FUSELAGE
13/14
REAR FUSELAGE
15
CONE/REAR FUSELAGE
16/17
CONE/REAR FUSELAGE
18
CENTER WING
19
OUTER WING
19.1
LEADING EDGES
21
LEADING EDGES
22
SPOILERS
23
INBOARD FLAP
24
OUTBOARD FLAP
25
AILERON
26
WING−TIP
27
VERTICAL STABILIZER
28
RUDDER
29
HORIZONTAL STABILIZER
31
ELEVATOR
32
PYLONS
35
NACELLE SECTION
36
NOSE GEAR AND DOORS
41
MAIN GEAR AND DOORS
42
NOSE FORWARD FUSELAGE
51
FORWARD FUSELAGE
52
CENTER FUSELAGE
Aircraft Structural SectionsStructure Sections and Components - A319 (Sheet 2 of 2)
FIGURE-09-10-04-991-001-B01
09-10-04Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
11/1
2
13/1
4
51
5223 24
2229
28
27
2526
16/1
7
18
3132
19.1
36
1935
15
21
41 42
N_AR_091004_1_0010301_01_01
Aircraft Structural SectionsStructure Sections and Components - A320 (Sheet 1 of 2)
FIGURE-09-10-04-991-001-C01
09-10-04Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
SECTION DESIGNATION
11/12
REAR FUSELAGE
13/14
REAR FUSELAGE
15
CONE/REAR FUSELAGE
16/17
CONE/REAR FUSELAGE
18
CENTER WING
19
OUTER WING
19.1
21
22
SPOILERS
23/24
INBOARD FLAP
OUTBOARD FLAP
25
AILERON
26
WING−TIP
27
VERTICAL STABILIZER
28
RUDDER
29
HORIZONTAL STABILIZER
31
ELEVATOR
32
PYLONS
35
NACELLE SECTION
36
NOSE GEAR AND DOORS
41
MAIN GEAR AND DOORS
42
NOSE FORWARD FUSELAGE
51
FORWARD FUSELAGE
52
CENTER FUSELAGE
FIXED AND MOVINGLEADING EDGES
N_AR_091004_1_0010302_01_00
Aircraft Structural SectionsStructure Sections and Components - A320 (Sheet 2 of 2)
FIGURE-09-10-04-991-001-C01
09-10-04Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
51
11/1
2
13/1
4
14A
21
42
15
16A
16/1
7
18
19
19.1
3635
3132
4152
23 2422
29
28
25
26
27
N_AR_091004_1_0010401_01_01
Aircraft Structural SectionsStructure Sections and Components - A321 (Sheet 1 of 2)
FIGURE-09-10-04-991-001-D01
09-10-04Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_AR_091004_1_0010402_01_00
REAR FUSELAGE
15
REAR FUSELAGE
16A
CONE/REAR FUSELAGE
16/17
CONE/REAR FUSELAGE
18
CENTER WING
19
OUTER WING
19.1
LEADING EDGES
21
LEADING EDGES
22
SPOILERS
23
INBOARD FLAP
24
OUTBOARD FLAP
25
AILERON
26
WING−TIP
27
VERTICAL STABILIZER
28
RUDDER
29
HORIZONTAL STABILIZER
31
ELEVATOR
32
PYLONS
35
NACELLE SECTION
36
NOSE GEAR AND DOORS
41
MAIN GEAR AND DOORS
42
51
CENTER FUSELAGE
52
REAR FUSELAGE
SECTION DESIGNATION
11/12
13/14
14A
NOSE FORWARD FUSELAGE
FORWARD FUSELAGE
FORWARD FUSELAGE
Aircraft Structural SectionsStructure Sections and Components - A321 (Sheet 2 of 2)
FIGURE-09-10-04-991-001-D01
09-10-04Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-05 COMPOSITE MATERIALS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-05-001-A01
General
1. Types of MaterialSome components and sections of the aircraft structure are made from composite materials seeFIGURE 09-10-05-991-001-AFIGURE 09-10-05-991-001-BFIGURE 09-10-05-991-001-CFIGURE09-10-05-991-001-D. The types of materials used are:- Carbon Fiber Reinforced Plastic (CFRP).- Glass Fiber Reinforced Plastic (GFRP).- Quartz Fiber Reinforced Plastic (QFRP).
09-10-05Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N_AR_091005_1_0010101_01_00
CARBON FIBER REINFORCED PLASTIC (CFRP)
GLASS FIBER REINFORCED PLASTIC (GFRP)
ARAMID FIBER REINFORCED PLASTIC (AFRP)
Composite Materials - A318Location of Composite materials on the External surfaces of the Aircraft
FIGURE-09-10-05-991-001-A01
09-10-05Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N_AR_091005_1_0010201_01_00
CARBON FIBER REINFORCED PLASTIC (CFRP)
GLASS FIBER REINFORCED PLASTIC (GFRP)
ARAMID FIBER REINFORCED PLASTIC (AFRP)
Composite Materials - A319Location of Composite materials on the External surfaces of the Aircraft
FIGURE-09-10-05-991-001-B01
09-10-05Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
N_AR_091005_1_0010301_01_00
CARBON FIBER REINFORCED PLASTIC (CFRP)
GLASS FIBER REINFORCED PLASTIC (GFRP)
ARAMID FIBER REINFORCED PLASTIC (AFRP)
Composite Materials - A320Location of Composite materials on the External surfaces of the Aircraft
FIGURE-09-10-05-991-001-C01
09-10-05Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_AR_091005_1_0010401_01_00
CARBON FIBER REINFORCED PLASTIC (CFRP)
GLASS FIBER REINFORCED PLASTIC (GFRP)
ARAMID FIBER REINFORCED PLASTIC (AFRP)
Composite Materials - A321Location of Composite materials on the External surfaces of the Aircraft
FIGURE-09-10-05-991-001-D01
09-10-05Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-06 FUSELAGE FRAMES AND H-ARM TABLE
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-06-001-A01
General
1. This chapter gives the H-Arm of each frame.The H-arm is used to calculate the CG. The H-arm is the length of the lever arm from the datumpoint to the specific station. The datum point is at 2540 mm (100 in) forward of the radome.
09-10-06Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
2.540m(100.00in)
X = 0
CL
FR2FR4
FR6FR8FR10
FR1
FR3
FR5FR7
FR9FR11
FR12FR14
FR16FR18
FR13 FR15
FR17
FR19
FR
NOSE
1
2
3
m (in)
2.540 (100.00)
H−ARMFR
11
12
14
15
13
m (in)
5.794 (228.10)
6.053 (238.30)
6.311 (248.46)
6.570 (258.64)
6.828 (268.82)
16
H−ARM
7.087 (279.00)
FR
17
18
19
20
23
m (in)
7.318 (288.11)
7.599 (299.17)
7.830 (308.27)
8.077 (318.00)
8.966 (353.00)
H−ARM
3.500 (137.80)
3.850 (151.57)
4.090 (161.02)
4.330 (170.47)
4.546 (178.98)
4.762 (187.48)
4.967 (195.55)
5.194 (204.49)
24 9.500 (374.00)
25 10.033 (395.00)
9 5.394 (212.36)
26 10.566 (416.00)
28
29
30
34
35
11.100 (437.00)
11.633 (458.00)
11.913 (469.00)
12.446 (490.00)
12.979 (511.00)
4
5
6
7
8
FR
37
m (in)
14.021 (552.00)
H−ARM
38 14.300 (563.00)
39 14.867 (585.32)
40 15.147 (596.32)
41 15.714 (618.64)
42 16.307 (642.00)
21 8.433 (332.00)
10 5.594 (220.24)
36 13.513 (532.00)
FR20FR22
FR24 FR24A
FR21
FR25
FR26FR28
FR29
FR30FR34
FR35
FR36
FR37
FR38
FR39
FR40
FR41
FR42
22 8.700 (342.50)
24A 9.766 (384.50)
N_AR_091006_1_0010102_01_00
Fuselage Frames and H-arm - A318Frame 1 to 42 (Sheet 1 of 2)
FIGURE-09-10-06-991-001-A01
09-10-06Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
FR42 FR44 FR46
FR54
FR43FR45
FR47
FR55
FR56
FR57
FR57A
FR58
FR59
FR60
FR61
FR62
FR63
FR64
FR65
FR66
FR67
FR68
FR69
FR70
FR71
FR72
FR73
FR74
FR75
FR76
FR77
FR78
FR79
FR80
FR81
FR82
FR83
FR84
FR85
FR86
FR87
FR
42
43
44
45
m (in)
16.307 (642.00)
H−ARMFR
60
61
63
64
62
m (in)
22.174 (873.00)
22.708 (894.00)
23.241 (915.00)
23.774 (936.00)
24.308 (957.00)
65
H−ARM
24.892 (980.00)
FR
66
67
68
69
72
m (in)
25.456 (1002.21)
25.953 (1021.77)
26.450 (1041.33)
26.975 (1062.02)
28.385 (1117.52)
H−ARM
16.840 (663.00)
17.374 (684.00)
17.907 (705.00)
18.440 (726.00)
18.974 (747.00)
19.507 (768.00)
20.041 (789.00)
20.574 (810.00)
73 28.785 (1133.27)
74 29.185 (1149.02)
57A 20.841 (820.50)
75 29.598 (1165.28)
76 30.011 (1181.54)
77
78
79
80
81
30.424 (1197.80)
30.536 (1202.21)
30.855 (1214.77)
31.174 (1227.33)
31.544 (1241.89)
46
47/54
55
56
57
FR
84
m (in)
32.824 (1292.29)
H−ARM
85 33.279 (1310.20)
86 33.734 (1328.11)
87 33.992 (1338.28)
70 27.534 (1084.02)
58 21.107 (531.00)
82 31.914 (1256.46)
71 27.934 (1099.77)
59 21.641 (852.00)
83 32.369 (1274.37)
CL
N_AR_091006_1_0010103_01_00
Fuselage Frames and H-arm - A318Frame 42 to 87 (Sheet 2 of 2)FIGURE-09-10-06-991-001-A01
09-10-06Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N_AR_091006_1_0010201_01_00
2.540m(100.00in)
X = 0
CL
FR1
FR2
FR3
FR4
FR5
FR6
FR7
FR8
FR9
FR10
FR11
FR12
FR13
FR14
FR15
FR16
FR17
FR18
FR19
FR20
FR
NOSE
1
2
3
m (in)
2.540 (100.00)
H−ARMFR
11
12
14
15
13
m (in)
5.794 (228.11)
6.052 (238.27)
6.311 (248.46)
6.570 (258.64)
6.828 (268.82)
16
H−ARM
7.087 (279.00)
FR
17
18
19
20
23
m (in)
7.318 (288.11)
7.599 (299.17)
7.830 (308.27)
8.077 (318.00)
8.966 (353.00)
H−ARM
3.500 (137.80)
3.850 (151.57)
4.090 (161.02)
4.330 (170.47)
4.546 (178.98)
4.762 (187.48)
4.967 (195.55)
5.194 (204.49)
24 9.500 (374.00)
25 10.033 (395.00)
9 5.394 (212.36)
26 10.566 (416.00)
27
28
29
30
34
11.100 (437.00)
11.633 (458.00)
12.167 (479.00)
12.700 (500.00)
13.233 (521.00)
4
5
6
7
8
FR
36
m (in)
14.300 (563.00)
H−ARM
37 14.808 (583.00)
38 15.088 (594.00)
39 15.655 (616.32)
40 15.934 (627.32)
41 16.501 (649.64)
21 8.433 (332.00)10 5.594 (220.24)
35 13.767 (542.00)22 8.700 (342.50)
24A 9.766 (384.50)
FR22
FR21FR23
FR24FR24A
FR25
FR26
FR27
FR28
FR29
FR30
FR31
FR34
FR35
FR36
FR37
FR38
FR39
FR40
FR41
FR42
FR43
42 17.094 (673.00)
43 17.628 (694.00)
OPTIONAL
Fuselage Frames and H-arm - A319Frame 1 to 43 (Sheet 1 of 2)
FIGURE-09-10-06-991-001-B01
09-10-06Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
FR
43
44
45
46
m (in)
17.628 (694.00)
H−ARMFR
58
59
61
62
60
m (in)
23.495 (925.00)
24.028 (946.00)
24.562 (967.00)
25.095 (988.00)
25.629 (1009.00)
63
H−ARM
26.162 (1030.00)
FR
64
65
66
67
70
m (in)
26.695 (1051.00)
27.280 (1074.00)
27.861 (1096.88)
28.352 (1116.22)
29.921 (1178.00)
H−ARM
18.161 (715.00)
18.694 (736.00)
19.228 (757.00)
19.761 (778.00)
20.295 (799.00)
20.828 (820.00)
21.361 (841.00)
21.895 (862.00)
71 30.321 (1193.75)
72 30.772 (1211.50)
55A 22.162 (872.50)
73 31.172 (1227.25)
74 31.572 (1243.00)
75
76
77
78
79
31.985 (1259.26)
32.398 (1275.52)
32.811 (1291.78)
32.923 (1296.19)
33.242 (1308.75)
47/51
52
53
54
55
FR
82
m (in)
34.301 (1350.44)
H−ARM
83 34.756 (1368.36)
84 35.211 (1386.27)
85 35.666 (1404.18)
68 28.843 (1135.35)
56 22.428 (883.00)
80 33.561 (1321.31)69 29.362 (1156.00)
57 22.962 (904.00)
81 33.931 (1335.87)
FR43
FR44
FR45
FR46
FR47FR51
FR52
FR53
FR54
FR55
FR55AFR56
FR57
FR58
FR59
FR60
FR61
FR62
FR63
FR64
FR65
FR66
FR67
FR68
FR69
FR70
FR71
FR72
FR73
FR74
FR75
FR76
FR77
FR78
FR79
FR80
FR81
FR82
FR83
FR84
FR85
FR86
FR87
86 36.121 (1422.10)
87 36.379 (1432.26)
N_AR_091006_1_0010202_01_00
CL
Fuselage Frames and H-arm - A319Frame 43 to 87 (Sheet 2 of 2)FIGURE-09-10-06-991-001-B01
09-10-06Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
N_AR_091006_1_0010301_01_00
2.540 m(100.00 in)
X = 0
CL
FR1
FR2
FR3
FR4
FR5
FR6
FR7
FR8
FR9
FR10
FR11
FR12
FR13
FR14
FR15
FR16
FR17
FR18
FR19
FR20
FR21 FR23
FR24
FR25
FR26
FR27
FR28
FR29
FR30
FR31
FR32
FR33
FR
NOSE
1
2
3
m (in)
2.540 (100.00)
H−ARMFR
11
12
14
15
13
m (in)
5.794 (228.11)
6.052 (238.27)
6.311 (248.46)
6.570 (258.66)
6.828 (268.82)
16
H−ARM
7.087 (279.02)
FR
17
18
19
20
23
m (in)
7.318 (288.11)
7.599 (299.17)
7.830 (308.27)
8.077 (317.99)
8.966 (352.99)
H−ARM
3.500 (137.80)
3.850 (151.57)
4.090 (161.02)
4.330 (170.47)
4.546 (178.98)
4.762 (187.48)
4.967 (195.55)
5.194 (204.49)
24 9.500 (374.02)
25 10.033 (395.00)
9 5.394 (212.36)
26 10.566 (415.98)
27 11.100 (437.01)
28
29
30
31
32
11.633 (457.99)
12.167 (479.02)
12.700 (500.00)
13.233 (520.98)
13.767 (542.01)
4
5
6
7
8
FR
34
m (in)
14.834 (584.02)
H−ARM
35 15.367 (605.00)
36 15.900 (625.98)
37 16.408 (645.98)
38 16.688 (657.01)
39
40
41
42
17.255 (679.33)
17.534 (690.31)
18.101 (712.64)
18.694 (735.98)
FR34FR36
FR38FR40
FR35FR37
FR39FR41
FR42
21 8.433 (332.01)10 5.594 (220.24) 33 14.300 (562.99)
Fuselage Frames and H-arm - A320Frame 1 to 42 (Sheet 1 of 2)
FIGURE-09-10-06-991-001-C01
09-10-06Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
FR
42
43
44
45
m (in)
18.694 (735.98)
H−ARMFR
54
55
57
58
56
m (in)
25.095 (987.99)
25.629 (1009.02)
26.162 (1030.00)
26.695 (1050.98)
27.229 (1072.01)
59
H−ARM
27.762 (1092.99)
FR
60
61
62
63
66
m (in)
28.296 (1114.02)
28.829 (1135.00)
29.362 (1155.98)
29.896 (1177.01)
31.577 (1243.19)
H−ARM
19.228 (757.01)
19.761 (777.99)
20.295 (799.02)
20.828 (820.00)
21.361 (840.98)
21.895 (862.01)
22.426 (882.99)
22.962 (904.02)
67 32.074 (1262.76)
68 32.571 (1282.32)
51 23.495 (925.00)
69 33.096 (1302.99)
70 33.655 (1325.00)
71
72
73
74
75
34.055 (1340.75)
34.506 (1358.50)
34.906 (1374.25)
35.306 (1390.00)
35.719 (1406.26)
46
47
48
49
50
FR
78
m (in)
36.657 (1443.19)
H−ARM
79 36.976 (1455.75)
80 37.295 (1468.31)
81 37.665 (1482.87)
82 38.035 (1497.44)
83
84
85
86
38.490 (1515.35)
38.945 (1533.27)
39.400 (1551.18)
39.855 (1569.09)
64 30.429 (1197.99)52 24.028 (945.98) 76 36.132 (1422.52)
FR42FR44
FR46FR48
FR50FR52
FR54FR56
FR43FR45
FR47FR49
FR51FR53
FR55FR57
FR58FR60
FR62
FR59FR61
87 40.113 (1579.25)
65 31.013 (1220.98)53 24.562 (967.01) 77 36.545 (1438.78)
FR64
FR63
FR66FR68
FR70FR72
FR74FR76
FR78FR80
FR65FR67
FR69FR71
FR73FR75
FR77FR79
FR81FR83
FR85
FR82FR84
FR86
FR87
N_AR_091006_1_0010302_01_00
CL
Fuselage Frames and H-arm - A320Frame 42 to 87 (Sheet 2 of 2)FIGURE-09-10-06-991-001-C01
09-10-06Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_AR_091006_1_0010401_01_00
FR35
FR34
FR33
FR32
FR31
FR30
FR29
FR28
FR27
FR26
FR25
FR24FR20
FR19
FR18
FR17
FR16
FR15
FR14
FR13
FR12
FR11
FR10
FR9
FR8
FR7
FR6
FR5
FR4
FR3
FR2
FR1
FR21
FR23
FR
NOSE
1
2
3
4
6
7
5
m (in)
2.540 (100.00)
8
H−ARMFR
12
13
15
16
14
m (in)
6.052 (238.27)
6.311 (248.46)
6.570 (258.66)
6.828 (268.82)
7.087 (279.02)
17
H−ARM
7.318 (288.11)
FR
18
19
20
21
23
25
24
m (in)
7.599 (299.17)
7.830 (308.27)
8.077 (317.99)
8.433 (332.01)
8.966 (352.99)
9.500 (374.02)
10.033 (395.00)
H−ARM
3.500 (137.80)
3.850 (151.57)
4.090 (161.02)
4.330 (170.47)
4.546 (178.98)
4.762 (187.48)
4.967 (195.55)
5.194 (204.49)
26 10.566 (415.98)
27 11.100 (437.01)
9
10
11
5.394 (212.36)
5.594 (220.24)
5.794 (228.11)
28 11.633 (457.99)
29 12.167 (479.02)
30
31
32
33
34
35
12.700 (500.00)
13.233 (520.98)
13.767 (542.01)
14.300 (562.99)
14.834 (584.02)
15.367 (605.00)
2.540 m(100.00 in)
X = 0
CL
Fuselage Frames and H-arm - A321Frame 1 to 35 (Sheet 1 of 3)
FIGURE-09-10-06-991-001-D01
09-10-06Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
FR
3535
135
235
3
m (in)
15.367 (605.00)
H−ARMFR
39
40
42
43
41
m (in)
21.522 (847.32)
21.801 (858.31)
22.368 (880.63)
22.962 (904.02)
23.495 (925.00)
44
H−ARM
24.025 (945.87)
FR
45
46
4747
147
2
474
473
m (in)
24.562 (967.01)
25.095 (987.01)
25.629 (1009.02)
26.162 (1030.00)
26.695 (1050.98)
27.229 (1072.01)
27.762 (1092.99)
H−ARM
15.900 (625.98)
16.433 (646.97)
16.967 (667.99)
17.501 (689.02)
18.034 (710.00)
18.567 (730.98)
19.101 (752.01)
19.634 (772.99)
475 28.296 (1114.02)
48 28.829 (1135.00)
36
37
38
20.168 (794.02)
20.676 (814.02)
20.955 (825.00)
49 29.362 (1155.98)
50 29.896 (1177.01)
51
52
53
54
55
56
30.429 (1197.99)
30.963 (1219.02)
31.496 (1240.00)
32.029 (1260.98)
32.563 (1282.01)
33.096 (1302.99)
354
355
356
357
358
FR35
FR35
FR35
FR35
FR35
FR35
FR35
FR36
FR37
FR38
FR39
FR40
FR41
FR42
FR43
FR44 FR46
FR47
FR47FR47
FR47
FR47
FR47
FR48
FR49
FR50
FR51
FR52
FR53
FR54
FR55
FR56
FR35
FR35
1
2
3
4
5
6
7
8
1
FR45
2
3
4
5
N_AR_091006_1_0010402_01_00
CL
Fuselage Frames and H-arm - A321Frame 35 to 56 (Sheet 2 of 3)FIGURE-09-10-06-991-001-D01
09-10-06Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
FR
56
57
58
59
m (in)
33.096 (1302.99)
H−ARMFR
67
68
70
71
69
m (in)
39.008 (1535.75)
39.505 (1555.32)
40.030 (1575.99)
40.589 (1597.99)
40.989 (1613.74)
72
H−ARM
41.440 (1631.50)
FR
73
74
75
76
77
78
m (in)
41.840 (1647.24)
42.240 (1662.99)
42.653 (1679.25)
43.066 (1695.51)
43.479 (1711.77)
43.591 (1716.18)
H−ARM
33.629 (1323.98)
34.163 (1345.00)
34.696 (1365.98)
35.230 (1387.01)
35.763 (1407.99)
36.297 (1429.02)
36.830 (1450.00)
37.363 (1470.99)
79 43.910 (1728.74)
80 44.229 (1741.30)
65
66
37.948 (1494.02)
38.511 (1516.18)
81 44.599 (1755.87)
82 44.969 (1770.43)
83
84
85
86
87
45.424 (1788.35)
45.879 (1806.26)
46.334 (1824.17)
46.789 (1842.09)
47.047 (1852.25)
60
61
62
63
64
FR56
FR57
FR58
FR59
FR60
FR61
FR62
FR63
FR64
FR65
FR66
FR67
FR68
FR69
FR70
FR71
FR72
FR73
FR74
FR75
FR76
FR77
FR78
FR79
FR80
FR81
FR82
FR83
FR84
FR85
FR86
FR87CL
N_AR_091006_1_0010403_01_00
Fuselage Frames and H-arm - A321Frame 56 to 87 (Sheet 3 of 3)FIGURE-09-10-06-991-001-D01
09-10-06Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-08 WING RIBS AND STATIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-08-001-A01
Wing Ribs and Stations
1. GeneralThis chapter gives the Wing Ribs and stations, see FIGURE 09-10-08-991-001-AFIGURE09-10-08-991-001-BThe position of each Wing Rib is identified by a station (STA). All measurements are:- At 90 degrees to Rib 1- Measured between Rib 1 and the intersection of each rib datum with the Front Spar datum at
the lower outside skin surface.
NOTE : The stations are given in centimeters with no conversion
09-10-08Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200
N_AR_091008_1_0010101_01_00
A
1868 mm(73.543 in)
STA0
STA70
STA141STA196
STA251
STA306
STA360
STA376
STA407
STA486
STA551
STA613
STA670
STA1120STA1166
STA1228
STA1287
STA1346
STA1406
RIB2
RIB1
RIB3RIB4
RIB5
RIB6
RIB7
RIB6B
RIB8RIB9
RIB10
STA1446
RIB11
RIB12
RIB13
RIB27
LH SHOWNRH SYMMETRICAL
NOTE : ALL STA NUMBERS ARE GIVEN IN cmSTATION REFERENCES GIVEN, APPLYTO THE INTERSECTION OF THE RIBDATUMS WITH THE FRONT SPAR DATUMAT THE OUTSIDE SKIN SURFACE.
A
AD
STA732
STA779STA827
STA874STA924STA970STA1020
STA1073
RIB14RIB15
RIB16RIB17RIB18
RIB20RIB21
RIB19
RIB22
RIB23
RIB24
RIB25
RIB26
WY
A
Wing Ribs and StationsA318/A319/A320
FIGURE-09-10-08-991-001-A01
09-10-08Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
1868 mm(73.543 in)
A
STA0
STA70
STA141STA196
STA251
STA306
STA360
STA376
STA407
STA486
STA551
STA613
STA670
STA1120STA1166
STA1228
STA1287
STA1346
STA1406
RIB2
RIB1
RIB3RIB4
RIB5RIB6
RIB7
RIB6B
RIB8RIB9RIB10
STA1446
RIB11
RIB12
RIB13
RIB27
LH SHOWNRH SYMMETRICAL
NOTE : ALL STA NUMBERS ARE GIVEN IN cmSTATION REFERENCES GIVEN, APPLYTO THE INTERSECTION OF THE RIBDATUMS WITH THE FRONT SPAR DATUMAT THE OUTSIDE SKIN SURFACE.
A
AD
STA732
STA779STA827
STA874STA924STA970STA1020
STA1073
RIB14RIB15
RIB16RIB17
RIB18
RIB20RIB21
RIB19
RIB22
RIB23
RIB24
RIB25
RIB26
A
WY
N_AR_091008_1_0010201_01_00
Wing Ribs and StationsA321
FIGURE-09-10-08-991-001-B01
09-10-08Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-09 HORIZONTAL STABILIZERS RIBS AND STATIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-09-001-A01
General
1. This chapter gives the horizontal stabilizer ribs and stations (see FIGURE 09-10-09-991-001-A).The position of each horizontal stabilizer rib is identified with a station (STA) which is the distancebetween the rib and RIB1 datum.
NOTE : The stations are given in centimeters with no conversion.
09-10-09Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
A
A
STA601
STA589
STA527
STA466
STA404
STA342
STA297
STA271
STA227
STA181
STA131
STA69
CL
STA0
RIB14
RIB13
RIB12
RIB11
RIB10
RIB9
RIB8
RIB7
RIB6
RIB5
RIB3 RIB4
RIB2 RIB1
LH SHOWNRH SYMMETRICAL
UPPER SURFACE
NOTE:ALL STA NUMBERS ARE GIVEN IN cm.
A
STA82
N_AR_091009_1_0010101_01_00
Horizontal StabilizerRibs and Stations
FIGURE-09-10-09-991-001-A01
09-10-09Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-10 DOOR SIZES AND LOCATIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-10-001-A01
General
1. This chapter gives data related to the aircraft doors. There are different types of door installed on theaircraft. The different doors are given in the sections that follow:- For the passenger/crew doors and emergency exit doors, see DESC 09-10-10-002-A01.- For the cargo compartment doors, see DESC 09-10-10-003-A01.- For the nose landing gear doors, see DESC 09-10-10-004-A01.- For the main landing gear doors, see DESC 09-10-10-005-A01.- For the APU doors, see DESC 09-10-10-006-A01.
09-10-10Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-10-002-A01
Passenger/Crew Doors and Emergency Exit Doors
1. GeneralThis section gives data related to the identification, location and clearances of the passenger/crewand emergency exit doors.
2. LocationFor the location of the passenger/crew and emergency exit doors see FIGURE 09-10-10-991-001-AFIGURE 09-10-10-991-001-BFIGURE 09-10-10-991-001-CFIGURE 09-10-10-991-001-D.
3. ClearancesFor the clearances of these doors:- FWD Pax/Crew doors, see FIGURE 09-10-10-991-002-A.- AFT Pax/Crew doors, see FIGURE 09-10-10-991-004-A.- Emergency Exits, see FIGURE 09-10-10-991-003-AFIGURE 09-10-10-991-003-BFIGURE
09-10-10-991-003-CFIGURE 09-10-10-991-003-D.
09-10-10Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N_A
R_0
9101
0_1_
0010
101_
01_0
0
5.02
m(1
6.5
ft)
12.8
9 m
(42.
29 ft
)
23.5
2 m
(77.
17 ft
)
FO
RW
AR
DP
AS
SE
NG
ER
/CR
EW
DO
OR
RE
AR
PA
SS
EN
GE
R/C
RE
W D
OO
RE
ME
RG
EN
CY
EX
IT
Passenger/Crew Doors and Emergency ExitsLocation - A318
FIGURE-09-10-10-991-001-A01
09-10-10Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N_A
R_0
9101
0_1_
0010
201_
01_0
0
5.02
m(1
6.5
ft)
12.8
3 m
(42.
1 ft)
13.6
8 m
(44.
9 ft)
25.9
1 m
(85
ft)
FO
RW
AR
DP
AS
SE
NG
ER
/CR
EW
DO
OR
RE
AR
PA
SS
EN
GE
R/C
RE
W D
OO
R
EM
ER
GE
NC
Y E
XIT
EM
ER
GE
NC
Y E
XIT
(OP
TIO
NA
L)
Passenger/Crew Doors and Emergency ExitsLocation - A319
FIGURE-09-10-10-991-001-B01
09-10-10Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
N_A
R_0
9101
0_1_
0010
301_
01_0
0
5.02
m(1
6.5
ft)
14.4
3 m
(47.
34 ft
)
15.2
8 m
(50.
13 ft
)
29.6
4 m
(97.
24 ft
)
FO
RW
AR
DP
AS
SE
NG
ER
/CR
EW
DO
OR
RE
AR
PA
SS
EN
GE
R/C
RE
W D
OO
RE
ME
RG
EN
CY
EX
IT
Passenger/Crew Doors and Emergency ExitsLocation - A320
FIGURE-09-10-10-991-001-C01
09-10-10Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
5.02
m(1
6.5
ft)
13.8
4 m
(45.
41 ft
)
27.4
9 m
(81.
33 ft
)
36.5
7 m
(119
.98
ft)
N_A
R_0
9101
0_1_
0010
401_
01_0
0
FO
RW
AR
DP
AS
SE
NG
ER
/CR
EW
DO
OR
RE
AR
PA
SS
EN
GE
R/C
RE
W D
OO
RE
ME
RG
EN
CY
EX
IT
Passenger/Crew Doors and Emergency ExitsLocation - A321
FIGURE-09-10-10-991-001-D01
09-10-10Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CL
2.54 m(100 in)
0.51 m(20.08 in)
CRITICALCLEARANCE LIMIT
0.48 m(18.9 in)
SEE 09−10−11
1.85 m(72.83 in)
0.03 m(1.18 in)
1.80 m(70.87 in)
0.81 m(31.89 in)
2.375 m(93.5 in)
CL
N_AR_091010_1_0020101_01_00
CL
Forward Passenger/Crew DoorsClearances
FIGURE-09-10-10-991-002-A01
09-10-10Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
CL
CL
N_AR_091010_1_0030101_01_00
0.56 m
A
A
(22.05 in)
SEE 09−10−11
0.12 m(4.72 in)
0.9 m(35.43 in)
0.495 m(19.49 in)
(TOP OF FLOOR)
A A
Emergency ExitsClearances - A318
FIGURE-09-10-10-991-003-A01
09-10-10Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
CL
CL
0.50 m
A
A
(19.68 in)
SEE 09−10−11
0.12 m(4.72 in)
0.9 m(35.43 in)
0.495 m(19.49 in)
(TOP OF FLOOR)
A AN_AR_091010_1_0030201_01_00
0.85 m(33.46 in)
OPTIONAL
Emergency ExitsClearances - A319
FIGURE-09-10-10-991-003-B01
09-10-10Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
CL
CL
0.50 m
A
A
(19.68 in)
SEE 09−10−11
0.12 m(4.72 in)
0.9 m(35.43 in)
0.495 m(19.49 in)
(TOP OF FLOOR)
A A
0.85 m(33.46 in)
N_AR_091010_1_0030301_01_00
Emergency ExitsClearances - A320
FIGURE-09-10-10-991-003-C01
09-10-10Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
CL
CL
0.76 m(29.92 in)
0.4 m(15.75 in)
0.43 m(16.93 in)
1.73 m(68.11 in)
0.83 m(32.68 in)
0.56 m(22.05 in)
CRITICAL CLEARANCELIMIT
CRITICAL CLEARANCELIMIT
(68.11 in)
0.83 m(32.68 in)
1.73 m
CENTER OFFREE AISLE
CENTER OFFREE AISLE
A
A
CL
0.04 m(1.57 in)
0.04 m(1.57 in)
B
B
FREE AISLE0.76 m
(29.92 in)
FREE AISLE
2.38 m(93.7 in)
1.52 m(59.84 in)
2.36 m(92.91 in)
0.39 m(15.35 in)
1.85 m(72.83 in)
A A0.39 m
(15.35 in)
2.36 m(92.91 in)
1.52 m(59.84 in)
(TOP OF FLOOR)
B B
0.56 m(22.05 in)
N_AR_091010_1_0030401_01_00
Emergency ExitsClearances - A321
FIGURE-09-10-10-991-003-D01
09-10-10Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091010_1_0040101_01_00
CRITICALCLEARANCELIMIT
0.58 m(22.83 in)
1.79 m(70.47 in)
0.81 m(31.89 in)
A
A
SEE 09−10−11
CL
CL
CL
0.03 m(1.18 in)
1.85 m(72.83 in)
0.60 m(23.62 in)
2.44 m(96.06 in)
A A
Aft Passenger/Crew DoorsClearances
FIGURE-09-10-10-991-004-A01
09-10-10Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-10-003-A01
Cargo Compartment Doors
1. GeneralThis section gives data related to the identification, location and clearances of the different cargocompartment doors (see FIGURE 09-10-10-991-006-AFIGURE 09-10-10-991-006-BFIGURE09-10-10-991-006-CFIGURE 09-10-10-991-006-D). There are three cargo compartment doors:- The forward cargo compartment door.- The aft cargo compartment door.- The bulk cargo compartment door (A320 and A321 only).
09-10-10Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N_A
R_0
9101
0_1_
0060
101_
01_0
0
7.89
m(2
5.89
ft)
18.9
6 m
(62.
2 ft)
RE
AR
CA
RG
OC
OM
PA
RT
ME
NT
DO
OR
FO
RW
AR
D C
AR
GO
CO
MP
AR
TM
EN
T D
OO
R
Cargo Compartments - A318Location (Sheet 1 of 3)
FIGURE-09-10-10-991-006-A01
09-10-10Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
1.495 m(58.858 in)
1.24 m(48.82 in)
3.945 m(151.31 in)
A
2.9 m(114.17 in)
SEE 09−10−11
A = CFM ENGINES 0.24 m (0.78 ft)PW ENGINES 0.39 m (1.27 ft)
1.33 m(52.36 in)
CL
A A
A
A
CL
N_AR_091010_1_0060102_01_01
Cargo Compartments - A318Clearances - Forward Cargo Compartment Door (Sheet 2 of 3)
FIGURE-09-10-10-991-006-A01
09-10-10Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
1.43 m(56.3 in)
1.23 m(48.43 in)
3.945 m(155.31 in)
SEE 09−10−111.33 m(52.36 in)
A
A
1.00 m(39.37 in)
A A
CL
CL
N_AR_091010_1_0060103_01_00
Cargo Compartments - A318Clearances - Aft Cargo Compartment Door (Sheet 3 of 3)
FIGURE-09-10-10-991-006-A01
09-10-10Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
8.16
m(2
6.77
ft)
20.5
8 m
(67.
52 ft
)
RE
AR
CA
RG
OC
OM
PA
RT
ME
NT
DO
OR
FO
RW
AR
D C
AR
GO
CO
MP
AR
TM
EN
T D
OO
R
N_A
R_0
9101
0_1_
0060
201_
01_0
0
Cargo CompartmentsLocation (Sheet 1 of 3)
FIGURE-09-10-10-991-006-B01
09-10-10Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
1.495 m(58.86 in)
1.24 m(48.82 in)
3.945 m(151.31 in)
A
2.71 m(106.69 in)
SEE 09−10−11
A = CFM ENGINES 0.67 m (2.20 ft)IAE ENGINES 0.51 m (1.67 ft)
1.82 m(74.65 in)
CL
A A
A
A
CL
N_AR_091010_1_0060202_01_01
Cargo CompartmentsClearances - Forward Cargo Compartment Door (Sheet 2 of 3)
FIGURE-09-10-10-991-006-B01
09-10-10Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
1.43 m(56.3 in)
1.23 m(48.43 in)
3.945 m(155.31 in)
SEE 09−10−111.82 m(71.65 in)
A
A
1.60 m(62.90 in)
A A
CL
CL
N_AR_091010_1_0060203_01_00
Cargo CompartmentsClearances - Aft Cargo Compartment Door (Sheet 3 of 3)
FIGURE-09-10-10-991-006-B01
09-10-10Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
8.16
m(2
6.77
ft)
22.6
9 m
(77.
44 ft
)
27.2
7 m
(89.
46 ft
)
FO
RW
AR
D C
AR
GO
CO
MP
AR
TM
EN
T D
OO
RR
EA
R C
AR
GO
CO
MP
AR
TM
EN
T D
OO
RB
ULK
CA
RG
OC
OM
PA
RT
ME
NT
DO
OR
N_A
R_0
9101
0_1_
0060
301_
01_0
0
Cargo CompartmentsLocation (Sheet 1 of 4)
FIGURE-09-10-10-991-006-C01
09-10-10Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
1.495 m(58.86 in)
1.24 m(48.82 in)
3.945 m(155.31 in)
A
2.71 m(106.69 in)
SEE 09−10−11
A = CFM ENGINE 2.27 m (7.45 ft)V2500 ENGINE 2.11 m (6.92 ft)
1.82 m(71.65 in)
CL
A A
A
A
CL
N_AR_091010_1_0060302_01_01
Cargo CompartmentsClearances - Forward Cargo Compartment Door (Sheet 2 of 4)
FIGURE-09-10-10-991-006-C01
09-10-10Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
1.43 m(56.3 in)
1.23 m(48.43 in)
3.945 m(155.31 in)
SEE 09−10−111.82 m(71.65 in)
A
A
2.03 m(79.92 in)
A A
CL
N_AR_091010_1_0060303_01_00
CL
Cargo CompartmentsClearances - Aft Cargo Compartment Door (Sheet 3 of 4)
FIGURE-09-10-10-991-006-C01
09-10-10Page 22
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
0.89 m(35.04 in)
0.77 m(30.32 in)
SEE 09−10−11
0.95 m(37.4 in)
CL
2.19 m(86.22 in)
6.10 m(240.16 in)
CL
N_AR_091010_1_0060304_01_00
A A
A
A
Cargo CompartmentsClearances - Bulk Cargo Compartment Door (Sheet 4 of 4)
FIGURE-09-10-10-991-006-C01
09-10-10Page 23
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_A
R_0
9101
0_1_
0060
401_
01_0
0
33.2
0 m
(108
.91
ft)
29.6
2 m
(97.
18 ft
)
8.16
m(2
6.77
ft)
BU
LK C
AR
GO
CO
MP
AR
TM
EN
T D
OO
RR
EA
R C
AR
GO
CO
MP
AR
TM
EN
T D
OO
RF
OR
WA
RD
CA
RG
OC
OM
PA
RT
ME
NT
DO
OR
Cargo CompartmentsLocation (Sheet 1 of 4)
FIGURE-09-10-10-991-006-D01
09-10-10Page 24
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
1.495 m(58.86 in)
1.24 m(48.82 in)
3.945 m(155.31 in)
A
2.71 m(106.69 in)
SEE 09−10−11
A = CFM ENGINE 6.54 m (21.45 ft)V2500 ENGINE 6.38 m (20.93 ft)
1.82 m(71.65 in)
CL
A
A
A A
N_AR_091010_1_0060402_01_02
Cargo CompartmentsClearances - Forward Cargo Compartment Door (Sheet 2 of 4)
FIGURE-09-10-10-991-006-D01
09-10-10Page 25
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_AR_091010_1_0060403_01_00
1.43 m(56.3 in)
1.23 m(48.43 in)
3.945 m(155.31 in)
SEE 09−10−111.82 m(71.65 in)
A
A
4.69 m(184.65 in)
A A
CL
Cargo CompartmentsClearances - Aft Cargo Compartment Door (Sheet 3 of 4)
FIGURE-09-10-10-991-006-D01
09-10-10Page 26
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
0.89 m(35.04 in)
0.77 m(30.32 in)
SEE 09−10−11
A
A
0.95 m(37.4 in)
CL
2.19 m(86.22 in)
8.76 m(344.88 in)
CL
N_AR_091010_1_0060404_01_00
A A
Cargo CompartmentsClearances - Bulk Cargo Compartment Door (Sheet 4 of 4)
FIGURE-09-10-10-991-006-D01
09-10-10Page 27
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-10-004-A01
Nose Landing Gear Doors
1. GeneralThis section gives data related to the location and clearances of the nose landing gear doors. Thenose landing gear has two pair of doors, the forward NLG doors and the rear NLG doors.
2. Location and ClearancesFor the location and clearances of the nose landing gear doors see FIGURE 09-10-10-991-010-A.
09-10-10Page 28
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091010_1_0100101_01_00
0.52 m(20.47 in)
1.50 m(59.01 in)
0.50 m(19.69 in)
1.40 m(55.19 in)
01 01
0.49 m(19.29 in)
2.13 m(83.86 in)
CG = 25% RC01
Door Sizes and LocationsNose Landing Gear Doors
FIGURE-09-10-10-991-010-A01
09-10-10Page 29
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-10-005-A01
Main Landing-Gear Doors
1. GeneralThis section gives data related to the location and clearances of the main landing-gear doors. SeeFIGURE 09-10-10-991-011-AFIGURE 09-10-10-991-011-BFIGURE 09-10-10-991-011-CFIGURE09-10-10-991-011-D.
09-10-10Page 30
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N_AR_091010_1_0110101_01_00
1.94 m(76.38 in)
0.485 m(19.095 in)
0.207 m(8.14 in)
0.14 m(5.51 in)
84°
1.23 m(48.43 in)
01
CG = 25% RC01
1.83 m(72.1 in)
13.97 m(550 in)
CL
GROUND LINE
1.76 m(69.29 in)
CL
A
LH SHOWNRH SYMMETRICAL
A
Location and ClearancesMain Landing Gear Doors - A318FIGURE-09-10-10-991-011-A01
09-10-10Page 31
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
1.94 m(76.38 in)
0.485 m(19.095 in)
0.207 m(8.14 in)
0.14 m(5.51 in)
84°
1.23 m(48.43 in)
01
CG = 25% RC01
1.83 m(72.1 in)
14.76 m(581.1in)
CL
GROUND LINE
1.76 m(69.29 in)
CL
A
LH SHOWNRH SYMMETRICAL
A
N_AR_091010_1_0110201_01_00
Location and ClearancesMain Landing Gear Doors - A319FIGURE-09-10-10-991-011-B01
09-10-10Page 32
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
1.83 m(72.1 in)
16.36 m(644.09 in)
CL
N_AR_091010_1_0110301_01_00
1.94 m(76.38 in)
0.485 m(19.095 in)
0.207 m(8.14 in)
0.14 m(5.51 in)
84°
1.23 m(48.43 in)
01
CG = 25% RC01
CL
GROUND LINE
1.76 m(69.29 in)
LH SHOWNRH SYMMETRICAL
A
A
Location and ClearancesMain Landing Gear Doors - A320 - Twin Wheel MLG (Sheet 1 of 2)
FIGURE-09-10-10-991-011-C01
09-10-10Page 33
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
0.485 m(19.095 in)
82.5°
1.27 m(50.0 in)
CL
0.16 m(6.3 in)
GROUND LINE
1.94 m(76.38 in)
1.76 m(69.29 in)
2.23 m(87.8 in)
16.23 m(638.98 in)
A
CL
LH SHOWNRH SYMMETRICAL
A
N_AR_091010_1_0110302_01_02
Location and ClearancesMain Landing Gear Doors - A320 - Optional Four Wheel Bogie MLG (Sheet 2 of 2)
FIGURE-09-10-10-991-011-C01
09-10-10Page 34
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
1.83 m(72.1 in)
20.62 m(811.81 in)
N_AR_091010_1_0110401_01_00
1.94 m(76.38 in)
0.485 m(19.095 in)
0.207 m(8.14 in)
0.14 m(5.51 in)
84°
1.23 m(48.43 in)
01
CG = 25% RC01
CL
GROUND LINE
1.76 m(69.29 in)
LH SHOWNRH SYMMETRICAL
A
A
CL
Location and ClearancesMain Landing Gear Doors - A321FIGURE-09-10-10-991-011-D01
09-10-10Page 35
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-10-006-A01
APU Doors
1. GeneralThis section gives data related to the location and clearances of the APU doors.
2. Location and ClearancesFor the location and clearances of the APU doors see FIGURE 09-10-10-991-014-A.
09-10-10Page 36
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
FR84
3.42 m(134.65 in)
4.05 m(159.45 in)
0101
CG = 25% RC01
FR80
CL
N_AR_091010_1_0140101_01_01
Location and ClearancesAPU Doors
FIGURE-09-10-10-991-014-A01
09-10-10Page 37
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-11 AIRCRAFT GROUND CLEARANCES
**ON A/C A318-100
DESC 09-10-11-001-A01
General
1. This chapter gives data related to the distance from different components/points on the aircraft tothe ground. For the basic ground clearances of the aircraft see FIGURE 09-10-11-991-001-A. Thedimensions given are approximate and can change with:- The aircraft weight.- The type of tire installed.- The aircraft attitude.- The climate conditions.For the ground clearances of the:- Extended leading edge slats see FIGURE 09-10-11-991-002-A.- Extended trailing edge flaps see FIGURE 09-10-11-991-003-A.- Extended spoilers see FIGURE 09-10-11-991-004-A.- Ailerons in the down position see FIGURE 09-10-11-991-005-A.- Ailerons in the up position see FIGURE 09-10-11-991-006-A.- Flap tracks with the flaps extended see FIGURE 09-10-11-991-007-A.
09-10-11Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N_AR_091011_1_0010101_01_00
J H G F M E B C A D
K2 KL
m
A
B
C
D
E (PW)
E (CFM)
F
ft
3.44 11.29
2.08 6.62
1.79 5.87
5.93 19.46
0.77 2.53
0.65 2.13
1.70 5.58
m
G
H
J
K
K2
L
M
ft
2.31 7.58
3.72 12.21
12.93 42.42
5.06 16.60
4.06 13.32
5.60 18.37
3.95 12.96
Aircraft Ground ClearancesBasic Ground Clearances
FIGURE-09-10-11-991-001-A01
09-10-11Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
X Y Z A’ B’ C’ D’ E’ F’ G’
HEIGHT FROM GROUND
m ft
X
Y
Z
A’
B’
C’
D’
E’
F’
G’
2.55 8.36
2.97 9.74
3.06 10.03
3.36 11.02
3.61 11.84
3.86 12.66
4.10 13.45
N_AR_091011_1_0020101_01_00
3.36 11.02
3.61 11.84
3.86 12.66
Aircraft Ground ClearancesLeading Edge Slats - ExtendedFIGURE-09-10-11-991-002-A01
09-10-11Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
C
HEIGHT FROM GROUND
m ft
A
B
C
2.05 6.72
2.77 9.08
2.81 9.21
DA
B
D 3.65 11.97
N_AR_091011_1_0030101_01_00
Aircraft Ground ClearancesTrailing Edge Flaps - ExtendedFIGURE-09-10-11-991-003-A01
09-10-11Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
HEIGHT FROM GROUND
m ft
Q
R
4.60 15.09
4.48 14.69
S
T
U
V
W
4.35 14.27
4.21 13.81
4.07 13.35
4.01 13.15
3.75 12.30
WVTSRQ
N_AR_091011_1_0040101_01_00
U
Aircraft Ground ClearancesSpoilers - Extended
FIGURE-09-10-11-991-004-A01
09-10-11Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
L M
HEIGHT FROM GROUND
m ft
L
M
4.19 13.74
3.84 12.60
N_AR_091011_1_0050101_01_00
Aircraft Ground ClearancesAilerons - Down
FIGURE-09-10-11-991-005-A01
09-10-11Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N P
N_AR_091011_1_0060101_01_00
HEIGHT FROM GROUND
m ft
N
P
4.57 15.0
4.37 14.3
Aircraft Ground ClearancesAilerons - Up
FIGURE-09-10-11-991-006-A01
09-10-11Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
J
HEIGHT FROM GROUND
m ft
H
J
K
2.18 7.15
2.66 8.73
3.10 10.17
KH
N_AR_091011_1_0070101_01_00
Aircraft Ground ClearancesFlap Track Fairings - Flaps Extended
FIGURE-09-10-11-991-007-A01
09-10-11Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
DESC 09-10-11-001-B01
General
1. This chapter gives data related to the distance from different components/points on the aircraft tothe ground. For the basic ground clearances of the aircraft see FIGURE 09-10-11-991-014-A. Thedimensions given are approximate and can change with:- The aircraft weight.- The type of tire installed.- The aircraft attitude.- The climate conditions.For the ground clearances of the:- Extended leading edge slats see FIGURE 09-10-11-991-015-A.- Extended trailing edge flaps see FIGURE 09-10-11-991-016-A.- Extended spoilers see FIGURE 09-10-11-991-017-A.- Ailerons in the down position see FIGURE 09-10-11-991-018-A.- Ailerons in the up position see FIGURE 09-10-11-991-019-A.- Flap tracks with the flaps extended see FIGURE 09-10-11-991-020-A.
09-10-11Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N_AR_091011_1_0140101_01_00
J H G F M E B C A D
L K
m
A
B
C (AFT)
C (FWD)
D (AFT)
D (FWD)
E (CFM)
ft
3.45 11.32
2.09 6.86
1.98 6.50
1.80 5.91
6.12 20.08
5.94 19.49
0.67 2.20
m
F
G
H
J
K
L
M
ft
1.71 5.61
2.25 7.38
3.73 12.24
12.17 39.93
4.02 13.19
5.51 18.08
3.96 12.99
NOTE: POINTS A, B, G, H, M AND P ARE MID DOOR AT FLOOR LEVEL.
OPTIONAL
E (IAE) 0.77 2.53
Aircraft Ground ClearancesBasic Ground Clearances
FIGURE-09-10-11-991-014-A01
09-10-11Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
X Y Z A’ B’ C’ D’ E’ F’ G’
HEIGHT FROM GROUND
m ft
X
Y
Z
A’
B’
C’
D’
E’
F’
G’
2.54 8.33
2.96 9.71
3.05 10.00
4.10 13.45
3.35 10.99
3.35 10.99
3.61 11.84
3.61 11.84
3.86 12.66
3.86 12.66
N_AR_091011_1_0150101_01_00
Aircraft Ground ClearancesLeading Edge Slats - ExtendedFIGURE-09-10-11-991-015-A01
09-10-11Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
C
HEIGHT FROM GROUND
m ft
A
B
C
2.05 6.72
2.77 9.08
2.81 9.21
DBA
D 3.65 11.97
N_AR_091011_1_0160101_01_00
Aircraft Ground ClearancesTrailing Edge Flaps - ExtendedFIGURE-09-10-11-991-016-A01
09-10-11Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
HEIGHT FROM GROUND
m ft
Q
R
4.60 15.09
4.48 14.69
S
T
U
V
W
4.35 14.27
4.21 13.81
4.07 13.35
4.01 13.15
3.75 12.30
WU VTSRQ
N_AR_091011_1_0170101_01_00
Aircraft Ground ClearancesSpoilers - Extended
FIGURE-09-10-11-991-017-A01
09-10-11Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
L M
HEIGHT FROM GROUND
m ft
L
M
4.18 13.71
3.84 12.60
N_AR_091011_1_0180101_01_00
Aircraft Ground ClearancesAilerons - Down
FIGURE-09-10-11-991-018-A01
09-10-11Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
N P
N_AR_091011_1_0190101_01_00
HEIGHT FROM GROUND
m ft
N
P
4.56 14.96
4.36 14.3
Aircraft Ground ClearancesAilerons - Up
FIGURE-09-10-11-991-019-A01
09-10-11Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
J
HEIGHT FROM GROUND
m ft
H
J
K
2.09 6.86
2.59 8.49
3.04 9.97
KH
N_AR_091011_1_0200101_01_00
Aircraft Ground ClearancesFlap Track Fairings - Flaps Extended
FIGURE-09-10-11-991-020-A01
09-10-11Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
DESC 09-10-11-001-C01
General
1. This chapter gives data related to the distance from different components/points on the aircraft tothe ground. For the basic ground clearances of the aircraft see FIGURE 09-10-11-991-021-A. Thedimensions given are approximate and can change with:- The aircraft weight.- The type of tire installed.- The aircraft attitude.- The climate conditions.For the ground clearances of the:- Extended leading edge slats see FIGURE 09-10-11-991-022-A.- Extended trailing edge flaps see FIGURE 09-10-11-991-023-A.- Extended spoilers see FIGURE 09-10-11-991-024-A.- Ailerons in the down position see FIGURE 09-10-11-991-025-A.- Ailerons in the up position see FIGURE 09-10-11-991-026-A.- Flap tracks with the flaps extended see FIGURE 09-10-11-991-027-A.
09-10-11Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
N_AR_091011_1_0210101_01_00
DABCENFGMHJ
NOTE: POINTS C AND D ARE HALFWAY BETWEEN NOSE AND MAIN GEARS.
LK
m
A
B
C
D
E (CFM)
E (IAE)
F
ft
3.47 11.38
2.09 6.86
1.86 6.10
6.00 19.68
0.68 2.23
0.78 2.56
1.72 5.64
m
G
H
J
K
L
M
N
ft
2.25 7.38
3.73 12.24
12.14 39.93
4.04 13.25
5.57 18.27
2.51 8.23
3.96 12.99
Aircraft Ground ClearancesBasic Ground Clearances
FIGURE-09-10-11-991-021-A01
09-10-11Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
W X Y Z A’ B’ C’ D’ E’ F’
HEIGHT FROM GROUND
m ft
W
X
Y
Z
A’
B’
C’
D’
E’
F’
2.57 8.43
2.98 9.78
3.07 10.07
4.09 13.42
3.36 11.02
3.61 11.84
3.86 12.66
N_AR_091011_1_0220101_01_00
3.36 11.02
3.61 11.84
3.86 12.66
Aircraft Ground ClearancesLeading Edge Slats - ExtendedFIGURE-09-10-11-991-022-A01
09-10-11Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
C
HEIGHT FROM GROUND
m ft
A
B
C
2.05 6.72
2.77 9.08
2.81 9.21
DBA
D 3.64 11.94
N_AR_091011_1_0230101_01_00
Aircraft Ground ClearancesTrailing Edge Flaps - ExtendedFIGURE-09-10-11-991-023-A01
09-10-11Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
HEIGHT FROM GROUND
m ft
P
Q
4.59 15.06
4.47 14.67
R
S
T
U
V
4.35 14.27
4.21 13.81
4.07 13.35
4.01 13.16
3.75 12.30
VT USRQP
N_AR_091011_1_0240101_01_00
Aircraft Ground ClearancesSpoilers - Extended
FIGURE-09-10-11-991-024-A01
09-10-11Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
L M
HEIGHT FROM GROUND
m ft
L
M
4.17 13.68
3.83 12.57
N_AR_091011_1_0250101_01_00
Aircraft Ground ClearancesAilerons - Down
FIGURE-09-10-11-991-025-A01
09-10-11Page 22
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
N_AR_091011_1_0260101_01_00
N P
HEIGHT FROM GROUND
m ft
N
P
4.55 14.93
4.35 14.27
Aircraft Ground ClearancesAilerons - Up
FIGURE-09-10-11-991-026-A01
09-10-11Page 23
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
J
HEIGHT FROM GROUND
m ft
H
J
K
2.18 7.15
2.66 8.73
3.10 10.17
KH
N_AR_091011_1_0270101_01_00
Aircraft Ground ClearancesFlap Track Fairings - Flaps Extended
FIGURE-09-10-11-991-027-A01
09-10-11Page 24
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
DESC 09-10-11-001-D01
General
1. This chapter gives data related to the distance from different components/points on the aircraft tothe ground. For the basic ground clearances of the aircraft see FIGURE 09-10-11-991-028-A. Thedimensions given are approximate and can change with:- The aircraft weight.- The type of tire installed.- The aircraft attitude.- The climate conditions.For the ground clearances of the:- Extended leading edge slats see FIGURE 09-10-11-991-029-A.- Extended trailing edge flaps see FIGURE 09-10-11-991-030-A.- Extended spoilers see FIGURE 09-10-11-991-031-A.- Ailerons in the down position see FIGURE 09-10-11-991-032-A.- Ailerons in the up position see FIGURE 09-10-11-991-033-A.- Flap tracks with the flaps extended see FIGURE 09-10-11-991-034-A.
09-10-11Page 25
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_AR_091011_1_0280101_01_00
DABCPENGFMHJ
NOTE: POINTS A, B, G, H, M, N AND P ARE MID DOOR AT FLOOR LEVEL.POINTS C AND D ARE EXTREMES OF STRAIGHT PORTION.
KL
m
A
B
C (AFT)
C (FWD)
D (AFT)
D (FWD)
E (CFM)
ft
3.46 11.35
2.08 6.82
1.99 6.53
1.80 5.91
6.13 20.11
5.94 19.49
0.68 2.23
m
G
H
J
K
L
M
N
ft
2.25 7.38
3.71 12.17
12.10 39.70
4.02 13.19
5.54 18.18
2.50 8.20
3.62 11.88
E (IAE)
F
0.79 2.59
1.72 5.64
P 3.53 11.58
Aircraft Ground ClearancesBasic Ground Clearances
FIGURE-09-10-11-991-028-A01
09-10-11Page 26
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
W X Y Z A’ B’ C’ D’ E’ F’
HEIGHT FROM GROUND
m ft
W
X
Y
Z
A’
B’
C’
D’
E’
F’
2.58 8.46
2.98 9.77
3.07 10.07
4.08 13.38
3.36 11.02
3.61 11.02
3.61 11.84
3.85 11.84
3.85 12.63
3.86 12.63
N_AR_091011_1_0290101_01_00
Aircraft Ground ClearancesLeading Edge Slats - ExtendedFIGURE-09-10-11-991-029-A01
09-10-11Page 27
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
HEIGHT FROM GROUND
m ft
A
B
C
1.95 6.39
2.84 9.31
2.71 8.89
CD
N_AR_091011_1_0300101_01_00
AG1 B H1
D 3.74 12.27
G1 2.49 8.16
H1 3.53 11.58
Aircraft Ground ClearancesTrailing Edge Flaps - ExtendedFIGURE-09-10-11-991-030-A01
09-10-11Page 28
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
HEIGHT FROM GROUND
m ft
P
Q
4.59 15.05
4.46 14.63
R
S
T
U
V
4.34 14.23
4.20 13.77
4.08 13.38
4.04 13.25
3.74 12.27
USRQP V
N_AR_091011_1_0310101_01_00
T
Aircraft Ground ClearancesSpoilers - Extended
FIGURE-09-10-11-991-031-A01
09-10-11Page 29
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
L M
HEIGHT FROM GROUND
m ft
L
M
4.15 13.61
3.81 12.50
N_AR_091011_1_0320101_01_00
Aircraft Ground ClearancesAilerons - Down
FIGURE-09-10-11-991-032-A01
09-10-11Page 30
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N P
N_AR_091011_1_0330101_01_00
HEIGHT FROM GROUND
m ft
N
P
4.53 14.86
4.33 14.20
Aircraft Ground ClearancesAilerons - Up
FIGURE-09-10-11-991-033-A01
09-10-11Page 31
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
HEIGHT FROM GROUND
m ft
H
J
K
1.91 6.26
2.31 7.57
2.96 9.71
J KH
N_AR_091011_1_0340101_01_00
Aircraft Ground ClearancesFlap Track Fairings - Flaps Extended
FIGURE-09-10-11-991-034-A01
09-10-11Page 32
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-12 AIRCRAFT GROUND SERVICE CONNECTIONS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-12-001-A01
General
1. This chapter gives data about the ground service connections of the aircraft.See FIGURE 09-10-12-991-001-AFIGURE 09-10-12-991-001-BFIGURE 09-10-12-991-001-CFIGURE09-10-12-991-001-D for the ground service connections general layout.This chapter gives data about the systems that follow:- Hydraulic System, see DESC 09-10-12-002-A01,- Electrical System, see DESC 09-10-12-003-A01,- Fuel System, see DESC 09-10-12-004-A01,- Potable Water System, see DESC 09-10-12-005-A01,- Waste Water Disposal System, see DESC 09-10-12-006-A01.
09-10-12Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
1 − EXTERNAL POWER PANEL2 − LOW PRESSURE CONDITIONED AIR CONNECTOR3 − IDG OIL FILLING4 − ENGINE OIL FILLING5 − WASTE SERVICE PANEL6 − POTABLE WATER SERVICE PANEL7 − APU OIL FILLING8 − YELLOW HYDRAULIC GROUND CONNECTOR
9 − GREEN HYDRAULIC GROUND CONNECTOR10 − BLUE HYDRAULIC GROUND CONNECTOR11 − PRESSURE REFUEL/DEFUEL COUPLING12 − HIGH PRESSURE AIR GROUND
13 − REFUEL/DEFUEL CONTROL PANEL14 − OVERWING REFUEL COUPLING
CONNECTORS FOR ENGINE STARTING
N_AR_091012_1_0010101_01_00
75
6
109
8
14
11
43
122
113
3
4
11
14
12
3 49 10
67
Ground Service ConnectionsGeneral Layout
FIGURE-09-10-12-991-001-A01
09-10-12Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
75
6
109
8
14
11
43
122
113
3
4
11
14
12
3 49 10
67
1 − EXTERNAL POWER PANEL2 − LOW PRESSURE CONDITIONED AIR CONNECTOR3 − IDG OIL FILLING4 − ENGINE OIL FILLING5 − WASTE SERVICE PANEL6 − POTABLE WATER SERVICE PANEL7 − APU OIL FILLING8 − YELLOW HYDRAULIC GROUND CONNECTOR
9 − GREEN HYDRAULIC GROUND CONNECTOR10 − BLUE HYDRAULIC GROUND CONNECTOR11 − PRESSURE REFUEL/DEFUEL COUPLING12 − HIGH PRESSURE AIR GROUND
13 − REFUEL/DEFUEL CONTROL PANEL14 − OVERWING REFUEL COUPLING
CONNECTORS FOR ENGINE STARTING
N_AR_091012_1_0010201_01_00
Ground Service ConnectionsGeneral Layout
FIGURE-09-10-12-991-001-B01
09-10-12Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
1 − EXTERNAL POWER PANEL2 − LOW PRESSURE CONDITIONED AIR CONNECTOR3 − IDG OIL FILLING4 − ENGINE OIL FILLING5 − WASTE SERVICE PANEL6 − POTABLE WATER SERVICE PANEL7 − APU OIL FILLING8 − YELLOW HYDRAULIC GROUND CONNECTOR
9 − GREEN HYDRAULIC GROUND CONNECTOR10 − BLUE HYDRAULIC GROUND CONNECTOR11 − PRESSURE REFUEL/DEFUEL COUPLING12 − HIGH PRESSURE AIR GROUND
13 − REFUEL/DEFUEL CONTROL PANEL14 − OVERWING REFUEL COUPLING
CONNECTORS FOR ENGINE STARTING
75
6
8
14
11
43
122
113
3
4
11
14
12
3 49 10
67
109
N_AR_091012_1_0010301_01_00
Ground Service ConnectionsGeneral Layout
FIGURE-09-10-12-991-001-C01
09-10-12Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
1 − EXTERNAL POWER PANEL2 − LOW PRESSURE CONDITIONED AIR CONNECTOR3 − IDG OIL FILLING4 − ENGINE OIL FILLING5 − WASTE SERVICE PANEL6 − POTABLE WATER SERVICE PANEL7 − APU OIL FILLING8 − YELLOW HYDRAULIC GROUND CONNECTOR
9 − GREEN HYDRAULIC GROUND CONNECTOR10 − BLUE HYDRAULIC GROUND CONNECTOR11 − PRESSURE REFUEL/DEFUEL COUPLING12 − HIGH PRESSURE AIR GROUND
13 − REFUEL/DEFUEL CONTROL PANEL14 − OVERWING REFUEL COUPLING
CONNECTORS FOR ENGINE STARTING
75
6
109
8
14
11
43
122
113
3
4
11
14
12
3 49 10
67
N_AR_091012_1_0010401_01_00
Ground Service ConnectionsGeneral Layout
FIGURE-09-10-12-991-001-D01
09-10-12Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-12-002-A01
Hydraulic System
**ON A/C A318-100
1. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Green HydraulicGround ConnectorsAccess Door 197CB
16.70 m (54.79 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Yellow HydraulicGround connectorsAccess Door 198CB
16.70 m (54.79 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Hydraulic ReservoirServicing PanelAccess Door 197EB
17.76 m (58.27 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Ground Service Panels
TABLE 1
NOTE : Distances are approximate.
**ON A/C A319-100
2. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Green HydraulicGround ConnectorsAccess Door 197CB
17.49 m (57.38 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Yellow HydraulicGround connectorsAccess Door 198CB
17.49 m (57.38 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
09-10-12Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Hydraulic ReservoirServicing PanelAccess Door 197EB
18.55 m (60.86 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Ground Service Panels
TABLE 2
NOTE : Distances are approximate.
**ON A/C A320-100 A320-200
3. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Green HydraulicGround ConnectorsAccess Door 197CB
19.08 m (62.60 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Yellow HydraulicGround connectorsAccess Door 198CB
19.08 m (62.60 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Hydraulic ReservoirServicing PanelAccess Door 197EB
20.15 m (66.11 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Ground Service Panels
TABLE 3
NOTE : Distances are approximate.
**ON A/C A321-100 A321-200
4. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Green HydraulicGround ConnectorsAccess Door 197CB
23.35 m (76.61 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
09-10-12Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Yellow HydraulicGround connectorsAccess Door 198CB
23.35 m (76.61 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Hydraulic ReservoirServicing PanelAccess Door 197EB
24.23 m (79.49 ft) 1.27 m (4.17 ft) 1.76 m (5.77 ft)
Ground Service Panels
TABLE 4
NOTE : Distances are approximate.
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
5. Technical SpecificationsThis section gives data related to the specifications of the ground service connections.
A. Ground TestReservoir PressurizationOn each ground service panel:- One connector AE80532N (suction).- One connector AE80531K (delivery).
B. Reservoir FillingOn the Green system ground service panel:- One connection AE96993E for pressurized supply.- One handpump filling connection for unpressurized (suction) supply.
09-10-12Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
RESERVOIR FILL SYSTEMHAND PUMP FILL CONNECTION
GROUND TESTPRESSURE
CONNECTION
GROUND TESTSUCTION
CONNECTIONRESERVOIR FILLCONNECTION
AE96993GM
GROUND SUPPLY
AE80531K AE80532N
1698GM
1008GM 1007GM 1006GM
197CB
A
AN_AR_091012_1_0020101_01_00
Ground Service ConnectionsGreen System Ground Service Panel
FIGURE-09-10-12-991-002-A01
09-10-12Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
GROUND CONNECTIONSUCTION
GROUNDCONNECTION
DELIVERY
AE80531K
AE80532N
N_AR_091012_1_0030101_01_00
2006GM
2008GM
A
Z197
A
Ground Service ConnectionsBlue System Ground Service Panel
FIGURE-09-10-12-991-003-A01
09-10-12Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
GROUND TESTPRESSURE CONNECTION
GROUND TESTSUCTION CONNECTION
AE80531K AE80532N
A
A
N_AR_091012_1_0140101_01_00
3008GM 3006GM
198CB
Ground Service ConnectionsYellow System Ground Service Panel
FIGURE-09-10-12-991-014-A01
09-10-12Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-12-003-A01
Electrical System
1. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
External PowerReceptacleAccess Door 121AL
2.55 m (8.37 ft) on centerline 2.00 m (6.56 ft)
Ground Service Panels
TABLE 1
NOTE : Distances are approximate.
2. Technical SpecificationsThis section gives data related to the specifications of the ground service connections.
A. External Power Receptacles:- One MS90362-3 - 90 KVA
B. Power Supply:- Three Phases, 115 V, 400 Hz
C. Electrical Connectors for Servicing:- AC Outlets: HUBBEL 5258- DC Outlets: HUBBEL 7472- Vacuum Cleaner Outlets: HUBBEL 5258
09-10-12Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
A
121AL
108VU
A
N_AR_091012_1_0040101_01_00
Ground Service ConnectionsExternal Power Receptacles
FIGURE-09-10-12-991-004-A01
09-10-12Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-12-004-A01
Fuel System
**ON A/C A318-100
1. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Refuel/DefuelIntegrated PanelAccess Door 192MB
12.00 m (39.37ft)
1.80 m (5.91 ft) 1.80 m (5.91 ft)
Refuel/DefuelCoupling, LeftAccess Door 522HB(Optional)
14.80 m (48.56ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
Refuel/DefuelCoupling, RightAccess Door 622HB
14.80 m (48.56ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
Gravity RefuelCoupling
16.70 m (54.79ft)
12.40 m (40.68 ft) 12.40 m (40.68 ft) 3.70 m (12.14 ft)
Ground Service Panels
TABLE 1
NOTE : Distances are approximate.
**ON A/C A319-100
2. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Refuel/DefuelIntegrated PanelAccess Door 192MB
12.80 m (41.99ft)
1.80 m (5.91 ft) 1.80 m (5.91 ft)
Refuel/DefuelCoupling, LeftAccess Door 522HB(Optional)
15.60 m (51.18ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
09-10-12Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Refuel/DefuelCoupling, RightAccess Door 622HB
15.60 m (51.18ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
Gravity RefuelCoupling
17.40 m (57.09ft)
12.40 m (40.68 ft) 12.40 m (40.68 ft) 3.70 m (12.14 ft)
Ground Service Panels
TABLE 2
NOTE : Distances are approximate.
**ON A/C A320-100 A320-200
3. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Refuel/DefuelIntegrated PanelAccess Door 192MB
14.40 m (47.24ft)
1.80 m (5.91 ft) 1.80 m (5.91 ft)
Refuel/DefuelCoupling, LeftAccess Door 522HB(Optional)
17.20 m (56.43ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
Refuel/DefuelCoupling, RightAccess Door 622HB
17.20 m (56.43ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
Gravity RefuelCoupling
19.10 m (62.66ft)
12.40 m (40.68 ft) 12.40 m (40.68 ft) 3.70 m (12.14 ft)
Ground Service Panels
TABLE 3
NOTE : Distances are approximate.
**ON A/C A321-100 A321-200
4. AccessThis section gives data related to the location of the ground service connections.
09-10-12Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Refuel/DefuelIntegrated PanelAccess Door 192MB
18.70 m (61.35ft)
1.80 m (5.91 ft) 1.80 m (5.91 ft)
Refuel/DefuelCoupling, LeftAccess Door 522HB(Optional)
21.50 m (70.54ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
Refuel/DefuelCoupling, RightAccess Door 622HB
21.50 m (70.54ft)
10.00 m (32.81 ft) 3.50 m (11.48 ft)
Gravity RefuelCoupling
23.40 m (76.77ft)
12.40 m (40.68 ft) 12.40 m (40.68 ft) 3.70 m (12.14 ft)
Ground Service Panels
TABLE 4
NOTE : Distances are approximate.
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
5. Technical SpecificationsThis section gives data related to the specifications of the ground service connections.
A. Refuel/Defuel Couplings:- Rigth wing: one standard ISO R45, 2.5 in.- Left wing: one optional standard ISO R45, 2.5 in.
B. Refuel Pressure:- Max. pressure: 3.45 bar (50 psi).
C. Refuel Flow:- 1400 l/minute (369.84 US gal/minute)
09-10-12Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
REFUEL/DEFUELCONTROL PANEL
NOTE: STANDARD CONFIGURATION OF REFUEL/DEFUEL PANEL.
A
N_AR_091012_1_0080101_01_01
FUELkg x 1000
QTY
RIGHTCTRLEFT
LEFT CTR RIGHT
LVLHI
OPEN
NORM
SHUT
OPEN
NORM
SHUT
REFUEL VALVESOPEN
NORM
SHUT
BATT POWERTESTHI LVL ON
OPEN LTS NORM
MODE SELECTREFUEL
OFF
DEFUEL / XFR
kg x 1000
PRESELECTED
DEC INC
ACTUALREFUEL
CKPT END
A
Ground Service ConnectionsRefuel/Defuel Panel
FIGURE-09-10-12-991-008-A01
09-10-12Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091012_1_0090101_01_00
RIB15
RIB14
A
41QM
40QM
LEADINGEDGE
WING FRONTSPAR
A
Ground Service ConnectionsRefuel/Defuel Couplings
FIGURE-09-10-12-991-009-A01
09-10-12Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091012_1_0150101_01_00
RIB19
RIB20
A
FWD
ADAPTER(REF ONLY)
GROUND CONNECTION(REF ONLY)
44QM
(45QM)
A
Ground Service ConnectionsGravity Refuel Couplings
FIGURE-09-10-12-991-015-A01
09-10-12Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-12-005-A01
Potable Water System
**ON A/C A318-100
1. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Potable WaterGround ServicePanelAccess Door 171AL
22.60 m (74.15 ft) 0.40 m (1.31 ft) 2.60 m (8.53 ft)
Drain PanelAccess Door 133AL
8.80 m (28.87 ft) 0.10 m (0.33 ft) 1.70 m (5.58 ft)
Drain PanelAccess Door 192NB
10.20 m (33.46 ft) 0.50 m (1.64 ft) 1.80 m (5.91 ft)
Ground Service Panels
TABLE 1
NOTE : Distances are approximate.
**ON A/C A319-100
2. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Potable WaterGround ServicePanelAccess Door 171AL
25.00 m (82.02 ft) 0.40 m (1.31 ft) 2.60 m (8.53 ft)
Drain PanelAccess Door 133AL
9.40 m (30.84 ft) 0.10 m (0.33 ft) 1.70 m (5.58 ft)
Drain PanelAccess Door 192NB
11.00 m (36.09 ft) 0.50 m (1.64 ft) 1.80 m (5.91 ft)
Ground Service Panels
TABLE 2
09-10-12Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
NOTE : Distances are approximate.
**ON A/C A320-100 A320-200
3. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Potable WaterGround ServicePanelAccess Door 171AL
28.70 m (94.16 ft) 0.40 m (1.31 ft) 2.60 m (8.53 ft)
Drain PanelAccess Door 133AL
9.40 m (30.84 ft) 0.10 m (0.33 ft) 1.70 m (5.58 ft)
Drain PanelAccess Door 192NB
12.50 m (41.01 ft) 0.50 m (1.64 ft) 1.80 m (5.91 ft)
Ground Service Panels
TABLE 3
NOTE : Distances are approximate.
**ON A/C A321-100 A321-200
4. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Potable WaterGround ServicePanelAccess Door 171AL
38.20 m (125.33ft)
0.40 m (1.31 ft) 2.60 m (8.53 ft)
Drain PanelAccess Door 133AL
9.40 m (30.84 ft) 0.10 m (0.33 ft) 1.70 m (5.58 ft)
Drain PanelAccess Door 192NB
12.50 m (41.01 ft) 0.50 m (1.64 ft) 1.80 m (5.91 ft)
Ground Service Panels
TABLE 4
NOTE : Distances are approximate.
09-10-12Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
5. Technical SpecificationsThis section gives data related to the specifications of the ground service connections.
A. Connections
(1) On the potable ground service panel (Access Door Access Door 171AL):- One standard 3/4 in. quick release filling connection.- One ground pressurization connection.
(2) On drain panel (Access Door 133AL):- One standard 3/4 in. drain connection.
(3) On drain panel (Access Door 192NB):- One standard 3/4 in. drain connection. with back- up mechanical control.- One standard 3/4 in. overflow and discharge connection with back up mechanical
control.
B. Capacity- 200 l (52.83 US gal).
C. Filling Rate- Max Filling Pressure: 3.45 bar (50 psi).- Flow rate: 67 l/minute (17.70 US gal/minute)
09-10-12Page 22
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091012_1_0100101_01_00
DRAIN CONNECTION
DRAIN CONNECTIONDISCHARGE ANDOVERFLOW PORT
FILL ANDDRAIN PORT
GROUND CONNECTION
PRESSURIZATION
B
C
Z133
Z171
Z138
A
BC
A
Ground Service ConnectionsPotable Water Ground Service Panel
FIGURE-09-10-12-991-010-A01
09-10-12Page 23
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-12-006-A01
Waste Water Disposal-System
**ON A/C A318-100
1. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Waste WaterGround ServicePanelAccess Door 172AR
22.90 m (75.13 ft) 0.80 m (2.62 ft) 2.80 m (9.19 ft)
Ground Service Panels
TABLE 1
NOTE : Distances are approximate.
**ON A/C A319-100
2. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Waste WaterGround ServicePanelAccess Door 172AR
24.90 m (81.69 ft) 0.80 m (2.62 ft) 2.80 m (9.19 ft)
Ground Service Panels
TABLE 2
**ON A/C A320-100 A320-200
3. AccessThis section gives data related to the location of the ground service connections.
09-10-12Page 24
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Waste WaterGround ServicePanelAccess Door 172AR
28.60 m (93.83 ft) 0.80 m (2.62 ft) 2.80 m (9.19 ft)
Waste WaterGround ServicePanelAccess Door 125AL(Optional)
3.40 m (11.15 ft) 1.20 m (3.94 ft) 2.40 m (7.87 ft)
Ground Service Panels
TABLE 3
**ON A/C A321-100 A321-200
4. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
Waste WaterGround ServicePanelAccess Door 172AR
35.50 m (116.47ft)
0.80 m (2.62 ft) 2.80 m (9.19 ft)
Waste WaterGround ServicePanelAccess Door 125AL(Optional)
3.40 m (11.15 ft) 1.20 m (3.94 ft) 2.40 m (7.87 ft)
Ground Service Panels
TABLE 4
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
5. Technical SpecificationsThis section gives data related to the specifications of the ground service connections.
A. Connections- One standard 1 in. flushing connection.- One standard 4 in. drain connection.
09-10-12Page 25
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
B. Single Toilet Capacity- Waste: 200 l (52.83 US gal)- Chemical fluid: 10 l (2.64 US gal).
C. Flushing Pressure- Maximum flushing pressure : 2.41 bar (35 psi)
D. Flow Rate- Maximum flow rate : 38 l/min (10.04 US gal/min)
09-10-12Page 26
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100
N_AR_091012_1_0130101_01_00
FILL AND RINSECONNECTION
TOILET DRAINCONNECTION
FR66 FR65
A
Z172
A
Ground Service ConnectionsWaste Water Ground Service Panel
FIGURE-09-10-12-991-013-A01
09-10-12Page 27
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200 A321-100 A321-200
FILL AND RINSE CONNECTION
TOILET DRAIN CONNECTION
CONNECTIONTOILET DRAIN
CONNECTIONFILL AND RINSE
SERVICE PANELFORWARD TOILET
(OPTIONAL)
N_AR_091012_1_0130201_01_00
Z172
Z125
FR11 FR12
A
FR66 FR65
AFT TOILET SERVICE PANEL
B
B
A
Ground Service ConnectionsWaste Water Ground Service Panel
FIGURE-09-10-12-991-013-B01
09-10-12Page 28
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-13 AIRCRAFT GROUNDING POINTS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-13-001-A01
General
**ON A/C A318-100
1. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
NLG 5.07 m (16.63 ft) On Centerline 0.94 m (3.08 ft)
LH MLG 15.32 m (50.26 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
RH MLG 15.32 m (50.26 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
Grounding Points Locations
TABLE 1
NOTE : Distances are approximate.
**ON A/C A319-100
2. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
NLG 5.07 m (16.63 ft) On Centerline 0.94 m (3.08 ft)
LH MLG 16.11 m (52.85 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
RH MLG 16.11 m (52.85 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
Grounding Points Locations
TABLE 2
NOTE : Distances are approximate.
**ON A/C A320-100 A320-200
3. AccessThis section gives data related to the location of the ground service connections.
09-10-13Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
NLG 5.07 m (16.63 ft) On Centerline 0.94 m (3.08 ft)
LH MLG 20.25 m (66.44 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
RH MLG 20.25 m (66.44 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
Grounding Points Locations
TABLE 3
NOTE : Distances are approximate.
**ON A/C A321-100 A321-200
4. AccessThis section gives data related to the location of the ground service connections.
Position from Aircraft CenterlineAccess
Position from Aftof Nose LH Side RH Side
Height fromGround
NLG 5.07 m (16.63 ft) On Centerline 0.94 m (3.08 ft)
LH MLG 21.97 m (72.08 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
RH MLG 21.97 m (72.08 ft) 3.79 m (12.43 ft) 1.07 m (3.51 ft)
Grounding Points Locations
TABLE 4
NOTE : Distances are approximate.
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
5. Technical SpecificationsThe grounding stud on each landing gear is designed for use with a clip-on connector, such as theAppleton TGR.The grounding stud are used to connect the aircraft to approved ground connection on the ramp, inthe hangar or through a ground earth spike for:- Refuel/Defuel operations,- Maintenance operations,- Bad Weather conditions.There is an additional grounding point located over the wing near the gravity refuel coupling, seeDESC 09-10-12-004-A01.
09-10-13Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
A
A
N_AR_091013_1_0010101_01_00
NOSE LANDING GEAR MAIN LANDING GEAR
LANDING GEAR
GROUND CABLE
A
Grounding PointLocation
FIGURE-09-10-13-991-001-A01
09-10-13Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-14 CARGO COMPARTMENTS
**ON A/C A318-100
DESC 09-10-14-001-A01
General
1. The lower deck of the aircraft has three cargo compartments:- Forward cargo compartment,- Aft cargo compartment,- Bulk cargo compartment.The total volume of the three cargo compartments is 21.30 m3 (752.20 ft3).
NOTE : See your customized WBM for accurate data related to the aircraft configuration.
A. FWD Cargo CompartmentThe fwd cargo compartment (n˚ 1) is designed for bulk cargo and baggage.The volume of the FWD cargo compartment is 6.72 m3 (237.31 ft3).See FIGURE 09-10-14-991-007-A for location and dimensions of the FWD compartment.
B. Aft Cargo CompartmentThe aft cargo compartment (n˚ 4) is designed for bulk cargo and baggage.The volume of the aft cargo compartment is 8.87 m3 (313.24 ft3).See FIGURE 09-10-14-991-008-A for location and dimensions of the aft compartment.
C. Bulk Cargo CompartmentThe bulk cargo compartment (n˚ 5) is designed for bulk cargo.The volume of the bulk cargo compartment is 5.71 m3 (201.65 ft3).See FIGURE 09-10-14-991-009-A for location and dimensions of the bulk compartment.
09-10-14Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
A
FR24A FR34
FR34
FR28
FR24A
FR24A
FR28
FR34 A
1.24
3 m
(4.0
7 ft)
1.429 m(4.68 ft)
2.637 m
(8.65 ft)
2.630 m(8.62 ft)
N_AR_091014_1_0070101_01_00
Forward Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-007-A01
09-10-14Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
FR47
FR57A
FR60
1.429 m(4.68 ft)2.630 m(8.62 ft)
A
FR60FR47
A
3.353 m
(11.00 ft)
FR60
FR57A
FR57
FR47
N_AR_091014_1_0080101_01_00
1.24
3 m
(4.0
7 ft)
/54
/54
/54
Aft Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-008-A01
09-10-14Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
A
FR60 FR65
FR60
FR62
FR63FR65
2.708 m
(8.88 ft)
A
FR65
FR63
FR60
1.558 m(5.11 ft)
N_AR_091014_1_0090101_01_00
Bulk Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-009-A01
09-10-14Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
DESC 09-10-14-001-B01
General
1. The lower deck of the aircraft has two cargo compartments:- Forward cargo compartment,- Aft cargo compartment,The total volume of the two cargo compartments is 27.56 m3 (973.27 ft3).
NOTE : See your customized WBM for accurate data related to the aircraft configuration.
A. FWD Cargo CompartmentThe FWD cargo compartment (n˚ 1) is designed for bulk cargo and baggage or transport ofULDs.The volume of the FWD cargo compartment is 8.51 m3 (300.53 ft3).See FIGURE 09-10-14-991-010-A for location and dimensions of the FWD compartment.
B. Aft Cargo CompartmentThe aft cargo compartment (n˚ 4 and 5) is designed for bulk cargo and baggage or transport ofULDs.The volume of the AFT cargo compartment is 19.05 m3 (672.74 ft3).See FIGURE 09-10-14-991-011-A for location and dimensions of the aft compartment.
09-10-14Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
FR24A FR34
FR24A
FR28
FR34
A
1.24
3 m
(4.0
7 ft)
1.430 m(4.69 ft)
3.345 m
(10.97 ft)
2.630 m(8.62 ft)
A
N_AR_091014_1_0100101_01_00
Forward Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-010-A01
09-10-14Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
FR47
1.430 m(4.69 ft)2.630 m(8.62 ft)
1.24
3 m
(4.0
7 ft)
A
4.421 m
(14.50 ft)
FR65
1.558 m(5.11 ft)
FR63
3.241 m
(10.63 ft)
7.662 m
(25.13 ft)
FR65FR47 FR59
FR59
FR55A
A
N_AR_091014_1_0110101_01_00
/51
/51
Aft Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-011-A01
09-10-14Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
DESC 09-10-14-001-C01
General
1. The lower deck of the aircraft has three cargo compartments:- Forward cargo compartment,- Aft cargo compartment,- Bulk cargo compartment.The total volume of the three cargo compartments is 37.45 m3 (1322.53 ft3).
NOTE : See your customized WBM for accurate data related to the aircraft configuration.
A. FWD Cargo CompartmentThe FWD cargo compartment (n˚ 1) is designed for bulk cargo and baggage or transport ofULDs.The volume of the FWD cargo compartment is 13.28 m3 (468.98 ft3).See FIGURE 09-10-14-991-013-A for location and dimensions of the FWD compartment.
B. Aft Cargo CompartmentThe aft cargo compartment (n˚ 3 and 4) is designed for bulk cargo and baggage or transport ofULDs.The volume of the aft cargo compartment is 18.26 m3 (644.85 ft3).See FIGURE 09-10-14-991-014-A for location and dimensions of the aft compartment.
C. Bulk Cargo CompartmentThe bulk cargo compartment (n˚ 5) is designed for bulk cargo and baggage.The volume of the bulk cargo compartment is 5.91 m3 (208.71 ft3).See FIGURE 09-10-14-991-015-A for location and dimensions of the bulk compartment.
09-10-14Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
1.430 m(4.69 ft)
1.24
3 m
(4.0
7 ft)
4.850 m
(15.91 ft)
A
FR24A FR34
FR34
FR31
FR28
FR24A
2.630 m(8.62 ft)
FR34
FR31
FR28
FR24A
A
N_AR_091014_1_0130101_01_00
Forward Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-013-A01
09-10-14Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
FR59
FR56
FR53FR52A
FR47
A
1.430 m(4.69 ft)
6.554 m
(21.50 ft)
1.24
2 m
(4.0
7 ft)
3.354 m
(11.00 ft)
3.200 m
(126.00 ft)
1.408 m(4.61 ft)
FR47
FR50
FR52A
FR53
FR56
FR59
A
FR47 FR59
2.630 m(8.62 ft)
N_AR_091014_1_0140101_01_00
Aft Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-014-A01
09-10-14Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
1.21
1 m
(3.9
7 ft)
1.558 m(5.11 ft)
1.408 m(4.62 ft)
2.630 m(8.62 ft)
3.241 m
(10.63 ft) 0.82
0 m
(2.6
9 ft)
0.968 m(3.17 ft)
FR65
FR63
FR59
FR59
FR63
FR65
A
FR59 FR65
N_AR_091014_1_0150101_01_00
A
Bulk Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-015-A01
09-10-14Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
DESC 09-10-14-001-D01
General
1. The lower deck of the aircraft has three cargo compartments:- Forward cargo compartment,- Aft cargo compartment,- Bulk cargo compartment.The total volume of the three cargo compartments is 50.95 m3 (1799.28 ft3).
NOTE : See your customized WBM for accurate data related to the aircraft configuration.
A. FWD Cargo CompartmentThe FWD cargo compartment (n˚ 1 and 2) is designed for bulk cargo and baggage or transportof ULDs.The volume of the FWD cargo compartment is 22.81 m3 (805.53 ft3).See FIGURE 09-10-14-991-016-A for location and dimensions of the FWD compartment.
B. Aft Cargo CompartmentThe aft cargo compartment (n˚ 3 and 4) is designed for bulk cargo and baggage or transport ofULDs.The volume of the AFT cargo compartment is 22.255 m3 (785.93 ft3).See FIGURE 09-10-14-991-017-A for location and dimensions of the aft compartment.
C. Bulk Cargo CompartmentThe bulk cargo compartment (n˚ 5) is designed for bulk cargo and baggage.The volume of the bulk cargo compartment is 5.88 m3 (207.65 ft3).See FIGURE 09-10-14-991-018-A for location and dimensions of the bulk compartment.
09-10-14Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
A
FR24A
FR28
FR31
FR34
FR35.2
FR35.5
N_AR_091014_1_0160101_01_00
8.149 m
(26.73 ft)
3.474 m
(11.39 ft)
4.675 m
(15.33 ft)
2.630 m(8.62 ft)
1.430 m(4.69 ft)
1.24
2 m
(4.0
7 ft)
FR35.5
FR35.2
FR34
FR31
FR28
FR24A
A
FR24A FR35.5
Forward Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-016-A01
09-10-14Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
A
8.154 m
(26.75 ft)
2.630 m(8.62 ft)
1.430 m(4.69 ft)
1.24
2 m
(4.0
7 ft)
FR59FR47.2
FR47.2
FR52A
FR56
FR59
FR59
FR56
FR52A
FR50
FR47.5
FR47.2
N_AR_091014_1_0170101_01_00
FR53
A
Aft Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-017-A01
09-10-14Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
FR65FR59
FR59
FR60
FR62
FR63
FR64
FR65
FR59
FR60
FR62
FR65 A1.558 m(5.11 ft)0.968 m(3.17 ft)
1.408 m(4.61 ft)2.630 m(8.62 ft)
3.241 m
(10.63 ft)
0.82
1 m
(2.6
9 ft)
1.21
1 m
(3.9
7 ft)
A
N_AR_091014_1_0180101_01_00
Bulk Cargo CompartmentLocation and Dimensions
FIGURE-09-10-14-991-018-A01
09-10-14Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-15 LOCATION OF HAZARDOUS MATERIALS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-15-001-A01
General
1. A number of items and areas on the aircraft contain Hazardous Materials.
WARNING : IDENTIFY WHICH HAZARDOUS MATERIALS WERE TRANSPORTED IN THECARGO COMPARTMENTS.
NOTE : The List of Radioactive and hazardous Element manual (LRE) gives information on thesematerials.
The FIGURE 09-10-15-991-001-AFIGURE 09-10-15-991-001-BFIGURE 09-10-15-991-001-CFIGURE09-10-15-991-001-D gives the general location of the Hazardous Materials that you can find on theaircraft.
NOTE : The number and arrangement of the portable equipment depend on the aircraftconfiguration.
09-10-15Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
BA
TT
ER
Y 2
N_A
R_0
9101
5_1_
0010
101_
01_0
0
CO
CK
PIT
OX
YG
EN
CY
LIN
DE
RS
AV
ION
ICS
CO
MP
AR
TM
EN
TA
CC
ES
S D
OO
R
BA
TT
ER
Y 1
(IF
INS
TA
LLE
D)
AP
U F
IRE
AP
U O
IL T
AN
K
SH
AD
ED
AR
EA
S ID
EN
TIF
Y P
ER
MIT
TE
DB
RE
AK
−IN
AR
EA
S O
N E
AC
HS
IDE
OF
TH
E A
IRC
RA
FT
VE
NT
SU
RG
E T
AN
KO
UT
ER
FU
EL
TA
NK
INN
ER
FU
EL
TA
NK
TA
NK
CE
NT
ER
FU
EL
IDG
OIL
TA
NK
S
NIT
RO
GE
N B
OT
TLE
HY
DR
AU
LIC
RE
SE
RV
OIR
DE
TE
CT
OR
S
EN
GIN
E F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LES
CA
RG
O F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
AP
U F
UE
L LI
NE
PA
SS
EN
GE
R A
ND
CR
EW
OX
YG
EN
BO
TT
LE
PO
RT
AB
LE F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
AP
U F
IRE
EX
TIN
GU
ISH
ER
LIN
ES
AP
U F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
FU
EL
LP V
ALV
ES
INN
ER
FU
EL
TA
NK
OU
TE
R F
UE
L T
AN
K
VE
NT
SU
RG
E T
AN
K
Hazardous MaterialsLocation - A318
FIGURE-09-10-15-991-001-A01
09-10-15Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
AV
ION
ICS
CO
MP
AR
TM
EN
TA
CC
ES
S D
OO
R
BA
TT
ER
Y 2
BA
TT
ER
Y 1
OU
TE
R F
UE
L T
AN
K
INN
ER
FU
EL
TA
NK
VE
NT
SU
RG
E T
AN
K
AC
T 4
(IF
INS
TA
LLE
D)
AC
T 6
(IF
INS
TA
LLE
D)
SH
AD
ED
AR
EA
S ID
EN
TIF
Y P
ER
MIT
TE
DB
RE
AK
−IN
AR
EA
S O
N E
AC
HS
IDE
OF
TH
E A
IRC
RA
FT
EN
GIN
E F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LES
INN
ER
FU
EL
TA
NK
OU
TE
R F
UE
L T
AN
K
VE
NT
SU
RG
E T
AN
K
AP
U O
IL T
AN
K
AP
U F
IRE
EX
TIN
GU
ISH
ER
LIN
ES
(IF
INS
TA
LLE
D)
AC
T 1
(IF
INS
TA
LLE
D)
AC
T 2
(IF
INS
TA
LLE
D)
AC
T 3
(IF
INS
TA
LLE
D)
AP
U F
IRE
DE
TE
CT
OR
S
AC
T 5
(IF
INS
TA
LLE
D)
TA
NK
CE
NT
ER
FU
EL
AP
U F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
AP
U F
UE
L LI
NE
IDG
OIL
TA
NK
S
NIT
RO
GE
N B
OT
TLE
HY
DR
AU
LIC
RE
SE
RV
OIR
CA
RG
O F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
PA
SS
EN
GE
R A
ND
CR
EW
OX
YG
EN
BO
TT
LE
PO
RT
AB
LE F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
FU
EL
LP V
ALV
ES
CO
CK
PIT
OX
YG
EN
CY
LIN
DE
RS
(IF
INS
TA
LLE
D)
N_A
R_0
9101
5_1_
0010
201_
01_0
0
AC
T:
AD
DIT
ION
AL
CE
NT
ER
TA
NK
Hazardous MaterialsLocation - A319
FIGURE-09-10-15-991-001-B01
09-10-15Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
N_A
R_0
9101
5_1_
0010
301_
01_0
0
BA
TT
ER
Y 2
BA
TT
ER
Y 1
EN
GIN
E F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LES
CO
CK
PIT
OX
YG
EN
CY
LIN
DE
RS
AV
ION
ICS
CO
MP
AR
TM
EN
TA
CC
ES
S D
OO
R
CE
NT
ER
FU
EL
TA
NK
(IF
INS
TA
LLE
D)
VE
NT
SU
RG
E T
AN
KA
CT
2(I
F IN
ST
ALL
ED
)
INN
ER
FU
EL
TA
NK
OU
TE
R F
UE
L T
AN
K
VE
NT
SU
RG
E T
AN
K
INN
ER
FU
EL
TA
NK
AC
T 1
(IF
INS
TA
LLE
D)
AP
U F
IRE
EX
TIN
GU
ISH
ER
LIN
ES
(IF
INS
TA
LLE
D)
AP
U F
UE
L LI
NE
AP
U F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
AP
U O
IL T
AN
K
AP
U F
IRE
DE
TE
CT
OR
S
IDG
OIL
TA
NK
S
NIT
RO
GE
N B
OT
TLE
HY
DR
AU
LIC
RE
SE
RV
OIR
CA
RG
O F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
PA
SS
EN
GE
R A
ND
CR
EW
OX
YG
EN
BO
TT
LE
PO
RT
AB
LE F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
FU
EL
LP V
ALV
ES
AC
T:
AD
DIT
ION
AL
CE
NT
ER
TA
NK
SH
AD
ED
AR
EA
S ID
EN
TIF
Y P
ER
MIT
TE
DB
RE
AK
−IN
AR
EA
S O
N E
AC
HS
IDE
OF
TH
E A
IRC
RA
FT
OU
TE
R F
UE
L T
AN
K
Hazardous MaterialsLocation - A320
FIGURE-09-10-15-991-001-C01
09-10-15Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
N_A
R_0
9101
5_1_
0010
401_
01_0
0
CO
CK
PIT
OX
YG
EN
CY
LIN
DE
RS
AV
ION
ICS
CO
MP
AR
TM
EN
TA
CC
ES
S D
OO
RBA
TT
ER
Y 2
BA
TT
ER
Y 1
EN
GIN
E F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LES
TA
NK
CE
NT
ER
FU
EL
WIN
G F
UE
L T
AN
K
VE
NT
SU
RG
E T
AN
K
VE
NT
SU
RG
E T
AN
K
WIN
G F
UE
L T
AN
K
AC
T 1
(IF
INS
TA
LLE
D)
AC
T 2
(IF
INS
TA
LLE
D)
SH
AD
ED
AR
EA
S ID
EN
TIF
Y P
ER
MIT
TE
DB
RE
AK
−IN
AR
EA
S O
N E
AC
HS
IDE
OF
TH
E A
IRC
RA
FT
AP
U F
UE
L LI
NE
AP
U F
IRE
EX
TIN
GU
ISH
ER
LIN
ES
AP
U O
IL T
AN
K
AP
U F
IRE
DE
TE
CT
OR
S
AP
U F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
IDG
OIL
TA
NK
S
NIT
RO
GE
N B
OT
TLE
HY
DR
AU
LIC
RE
SE
RV
OIR
CA
RG
O F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
PA
SS
EN
GE
R A
ND
CR
EW
OX
YG
EN
BO
TT
LE
PO
RT
AB
LE F
IRE
EX
TIN
GU
ISH
ER
BO
TT
LE
FU
EL
LP V
ALV
ES
AC
T:
AD
DIT
ION
AL
CE
NT
ER
TA
NK
Hazardous MaterialsLocation - A321
FIGURE-09-10-15-991-001-D01
09-10-15Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-10-16 LANDING GEARS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-10-16-001-A01
General
1. This chapter gives details on the landing gears.- For Landing Gear footprint, see FIGURE 09-10-16-991-001-AFIGURE 09-10-16-991-001-
BFIGURE 09-10-16-991-001-CFIGURE 09-10-16-991-001-D,- For Nose Landing Gear description, see FIGURE 09-10-16-991-002-A,- For Main Landing Gear description, see FIGURE 09-10-16-991-003-A,- For Landing Gear Doors description, see FIGURE 09-10-16-991-004-A.
09-10-16Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100
N_AR_091016_1_0010101_01_00
0.50 m(19.7 in)
10.252 m(33.64 ft)
0.927 m(36.5 in)
7.59 m(24.90 ft)
CL
FootprintLanding Gear
FIGURE-09-10-16-991-001-A01
09-10-16Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A319-100
0.50 m(19.7 in)
11.039 m(36.22 ft)
0.927 m(36.5 in)
7.59 m(24.90 ft)
N_AR_091016_1_0010201_01_00
CL
FootprintLanding Gear
FIGURE-09-10-16-991-001-B01
09-10-16Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
0.50 m(19.7 in)
12.64 m(41.47 ft)
0.927 m(36.5 in)
7.59 m(24.90 ft)
CL
N_AR_091016_1_0010301_01_00
FootprintLanding Gear - Twin Wheel MLG (Sheet 1 of 2)
FIGURE-09-10-16-991-001-C01
09-10-16Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A320-100 A320-200
0.50 m(19.7 in)
12.64 m(41.47 ft)
0.78 m(30.7 in)
7.59 m(24.90 ft)
CL
N_AR_091016_1_0010302_01_00
1.005 m(39.5 ft)
FootprintLanding Gear - Four Wheel Bogie MLG (Optional, A320 only) (Sheet 2 of 2)
FIGURE-09-10-16-991-001-C01
09-10-16Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A321-100 A321-200
0.50 m(19.7 in)
16.91 m(55.47 ft)
0.927 m(36.5 in)
7.59 m(24.90 ft)
CL
N_AR_091016_1_0010401_01_00
FootprintLanding Gear
FIGURE-09-10-16-991-001-D01
09-10-16Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
ACTUATINGCYLINDER
NOSE WHEELSTEERING
SERVO CONTROL
STEERINGACTUATINGCYLINDER
TORQUE LINK
TOWINGFITTING
SHOCKABSORBER
DOWNLOCKPROXIMITY
DETECTORS
N_AR_091016_1_0020101_01_00
DescriptionNose Landing Gear
FIGURE-09-10-16-991-002-A01
09-10-16Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091016_1_0030101_01_00
ACTUATINGCYLINDERLOCK STAY
UNLOCKACTUATOR
SIDE STAY
TORQUE LINK
SHOCKABSORBER
MAIN FITTING
DescriptionTwin Wheel MLG (Sheet 1 of 2)FIGURE-09-10-16-991-003-A01
09-10-16Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091016_1_0030102_01_00
ACTUATING CYLINDER
DOWNLOCKACTUATOR
LOCK STAY
LEG UNIT
SHOCK ABSORBER
BRAKE BAR
TORQUE LINK
STRUT ASSEMBLY
PITCH TRIMMER
DescriptionFour Wheel Bogie MLG (Optional A320 only) (Sheet 2 of 2)
FIGURE-09-10-16-991-003-A01
09-10-16Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
FR9
FR20
LEG DOOR
AFT DOORS
ROTATING RODASSY
FITTING
FWD DOORS
CONTROL ROD
DOORACTUATINGCYLINDER
BELL CRANK DOOR UPLOCKASSENBLY
DRAG STRUTASSY
GEAR UPLOCKASSEMBLY
N_AR_091016_1_0040101_01_00
DoorsNose Landing Gear (Sheet 1 of 3)FIGURE-09-10-16-991-004-A01
09-10-16Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091016_1_0040102_01_00
MAIN DOOR(HYDRAULICALLY OPERATED)
FIXEDRAMPS
UPLOCKROLLER
ADJUSTABLERAMP
NOTE:MAIN DOOR SHOWN OPEN IN GROUND MAINTENANCE POSITION.
STEPS
FIXEDFAIRING
HINGEDFAIRING
HINGED FAIRING(MECHANICALLY OPERATED)
PROXIMITY SENSORS
DOOR ACTUATING CYLINDER
DoorsTwin Wheel MLG (Sheet 2 of 3)FIGURE-09-10-16-991-004-A01
09-10-16Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
N_AR_091016_1_0040103_01_00
NOTE:MAIN DOOR SHOWN OPEN IN GROUND MAINTENANCE POSITION.
HINGEDFAIRING
FIXEDFAIRING
DOOR ACTUATINGCYLINDER
AJUSTABLERAMP
UPLOCKROLLER
DOORRAMPS
STEPS
MAIN DOOR
DoorsFour Wheel Bogie MLG (Optional A320 only) (Sheet 3 of 3)
FIGURE-09-10-16-991-004-A01
09-10-16Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-20-01 QUICK REFERENCE DATA
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-20-01-001-A01
General
1. This chapter is broken down as follows:
A. Aircraft Recovery Logic Charts DESC 09-20-01-002-A01.
B. Aircraft Recovery Process Document DESC 09-20-01-004-A01.
C. IATA Aircraft Recovery Quick Reference Check List TASK 09-20-01-869-801-A01.
09-20-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-20-01-002-A01
Aircraft Recovery Logic Chart
NOTE : The charts are not in chronological sequence for recovery. Make a selection of the chartsapplicable to each recovery scenario.
1. See DESC 02-10-01-002-A01 for description of aircraft recovery charts and the way to use them.When you use these charts, the conditions that follow are assumed:- Warnings and cautions are not included on the recovery charts.- The aircraft operator has full responsibility for all the aircraft recovery operation.- The recovery operation can only start when the local and state Investigative Authorities release
the aircraft.- All company, local and state health and safety regulations are obeyed.- All hazardous materials are identified and correctly handled.- The standard ”Aircraft Status for Maintenance” is in general not available (see AMM 00
Introduction, Item 7).- The aircraft is possibly in an unusual attitude and can be unstable.- Some of the steps listed are possibly not in chronological sequence because each recovery
operation is different and the recovery procedure must be adapted.- It is possible that some of the steps listed are completed more than one time.
09-20-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CHART I
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
INCIDENT
PERSONNEL FROM THE AIRLINE,INVESTIGATIVE AUTHORITIESAND AIRPORT TO BE ADVISED
THE AIRCRAFT OPERATORHAS FULL RESPONSIBILITY
FOR THE RECOVERY
ADVISE INTERNALLY ACCORDINGTO AIRLINE PROCESSES
BASIC INCIDENT INFORMATION:−GET AND RECORD INITIAL DATA−FUEL ON BOARD−ANY HAZARDOUS MATERIALS−AIRCRAFT STATUS −CURRENT AND FORECAST WEATHER
RECOVERY MANAGER ASSUMESRESPONSIBILITY
RECOVERY TEAM SELECTED
PREPARE PERSONALEQUIPMENT
PREPARE LOCALAIRCRAFT
RECOVERYEQUIPMENT
COMMUNICATE WITHAIRPORT AND INVESTIGATIVE
AUTHORITIES, RECORD NAMES,POSITIONS AND CONTACT
NUMBERS
REMOVE FDR AND CVR PERINVESTIGATIVE AUTHORITIES
AIRCRAFT RELEASED BYINVESTIGATIVE AUTHORITY
GO TO CHART IIA
LIAISE WITHRECOVERYMANAGER
( )
SEE 01−00−00
SEE 09−20−02
N_AR_092001_1_0010101_01_00
SEE FIGURE 09−20−01−991−002
Aircraft Recovery Logic ChartChart I
FIGURE-09-20-01-991-001-A01
09-20-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
ARE THERE VISIBLE FLUIDLEAKS?
DOES THE AIRCRAFT HAVETO BE STABILIZED?
INITIAL SURVEY OF AIRCRAFT
STEPA
DO A CHECK FOR OBVIOUSSTRUCTURAL DAMAGE
STEPB
STEPC
STEPD
STEPE
LANDING GEAR STATUS
STEPF
IDENTIFY SIGNS OFDISTORTION, BUCKLING,CRACKING ETC.
IDENTIFY MISSINGCOMPONENTS SUCH ASLANDING GEAR, FLAPS,ETC.
GO TO CHART IX( )
AND GO TO STEP CSEE SRM 51−11−00
GO TO CHART IV STEP A( )
GO TO STEP D
GO TO CHART VI( )
GO TO STEP E
GO TO CHART XIII( )
GO TO CHART IIBSTEP G
YES
NO
YES
NO
SEE 02−40−01 FOR HEALTH& SAFETY DETAILS
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART IIA
SEE FIGURE 09−20−01−991−009
SEE FIGURE 09−20−01−991−004
SEE FIGURE 09−20−01−991−006
SEE FIGURE 09−20−01−991−013
N_AR_092001_1_0020101_01_01
Aircraft Recovery Logic ChartChart IIA (Sheet 1 of 2)
FIGURE-09-20-01-991-002-A01
09-20-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
INITIAL SURVEY OF AIRCRAFT CONT’D
STEPG
WEIGHT AND CG POSITIONMANAGEMENT
STEPH
STEPI
ARE THERE ANY STRUCTURALCONCERNS?
STEPJ
ARE THERE ANY ENVIRONMENTALCONCERNS?
STEPK
( )
APPLICABLE AND GO TO STEP I
GO TO STEP D
GO TO STEP E
INSTALL PROTECTIVE COVERS:
( )
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART IIB
ARE HAZARDOUS MATERIALSIDENTIFIED AND ARE THEY OFCONCERN?
FOR LOCALIZATIONSEE 09−10−05 AND
SEE 09−10−15
WILL THIS BE A LENGTHYRECOVERY?
YES
NO
YES
NO
YES
NO
YES
NO
GO TO STEP J
GO TO STEP I
GO TO CHART XI
AND COMPLETE WORKSHEETS(
IF
TO STEP JADVISE HAZMAT TEAM AND GO
TEAM AND GO TO STEP KADVISE HAZMAT RESPONSE
ENGINES, PITOT HEADS, ETC.AND GO TO CHART III
AND
N_AR_092001_1_0020103_01_00
SEE SRM 51−11−00
SEE 03−00−00 SEE 09−50−01)
SEE FIGURE 09−20−01−991−003
SEE FIGURE 09−20−01−991−011
Aircraft Recovery Logic ChartChart IIB (Sheet 2 of 2)
FIGURE-09-20-01-991-002-A01
09-20-01Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CHART III
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
IS AIRCRAFT ECONOMICALLY RECOVERABLE?
MAKE THE DECISION WITHINPUT FROM THE OPERATOR,INSURANCE SURVEYER ANDAIRCRAFT MANUFACTURER
NOTE:
FURTHER NOTIFICATION
PREPARE FOR RECOVERYAFTER RELEASE BY INVESTIGATIVE AUTHORITIES
WILL SECONDARY DAMAGEBE ACCEPTABLE?
WHO WILL RECOVERAIRCRAFT?
AIRLINE CONTRACTOR AIRPORT
GO TO CHART VII
END
SIGN CONTRACT, MAKE SURETHAT ARM PROCEDURES AREFOLLOWED, RELEASE FORMSAND WAIVERS
ASSIGN AIRLINEREPRESENTATIVE TOOVERSEE RECOVERY ANDOBTAIN REPORT
NO YES
PROCEED AS "YES" UNTIL
( )
SEE 02−00−00
N_AR_092001_1_0030101_01_00
SEE FIGURE 09−20−01−991−007
Aircraft Recovery Logic ChartChart III
FIGURE-09-20-01-991-003-A01
09-20-01Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART IV
IDENTIFY FLUID LEAKS
MAKE SURE AIRCRAFT IS CORRECTLY GROUNDED
"B" HYDRAULICOR ENGINE OIL"A" FUEL "C" LAVATORY "D" CARGO "E" WATER
ADVISE HAZMATTEAM TO IDENTIFY,
CONTAIN ANDREMOVE
ATTEMPT SPILLCONTAINMENT
DRAIN SYSTEM
DRAIN SYSTEM IFACCESS AVAILABLE
ATTEMPT SPILLCONTAINMENTIDENTIFY SOURCE
MAKE SUREHAZMAT TEAMAWARE OF ANYGROUND SPILLAGE
ATTEMPT SPILLCONTAINMENT
CAN LINES BECAPPED, VALVESBE CLOSED, ETC?
CAPPED, VALVESBE CLOSED,
HOLES PLUGGED,ETC.?
CAN LINES BE
DEFUEL OFAIRCRAFTBECOMESPRIORITY
GO TO"C"
GO TO"B"
DRAINSYSTEM
GO TO"D"
GO TO"E"
NOYES
YESNO
GO TO CHART X
GO TO CHART IIASTEP D
ISOLATEELECTRICALPOWER (SEE
CHART IX FOR DETAILS
IDENTIFY SOURCE
)(
( )
)
N_AR_092001_1_0040101_01_00
SEE FIGURE 09−20−01−991−010
SEE FIGURE 09−20−01−991−002
SEE FIGURE 09−20−01−991−009
Aircraft Recovery Logic ChartChart IV
FIGURE-09-20-01-991-004-A01
09-20-01Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
CHART V
REMOVALCATERING
CONTROLCG DURINGOFF−LOAD
CAN CARGO DOOR BEACCESSED?
YESNO
EXCAVATE/PREPARE ROADWAY TOALLOW ACCESS
TO DOOR
CAN ELECTRICALPOWER TO THE
AIRCRAFT BEESTABLISHED?
YESNO
CONTACT AIRBUS FORFURTHER INSTRUCTIONS
CANCARGO
DOOR BEOPENED
MANUALLY
NO
HOIST DOOR TOOPEN
CAN DOOR BEUNLOCKED
AND HOISTEDWITH A CRANE?
YES
NO
MANUALLYOPERATEDOORS
YES
OPERATE DOORSNORMALLY
CAN CARGOLOADING
SYSTEM (CLS)BE USED?
YES
NO
UNLOAD CARGOCOMPARTMENTS
CONTROL CGDURING OFF−LOAD
UNLOAD ASMUCH ASPOSSIBLE
MANUALLY (MAYBE NECESSARY
TO CUTCONTAINERSFOR ACCESS)
SEE 05−50−00
SEE 05−50−00
SEE 05−50−00
GO TO CHART VI STEP G( )
REMOVAL OF CARGO
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
N_AR_092001_1_0050101_01_00
SEE FIGURE 09−20−01−991−006
Aircraft Recovery Logic ChartChart V
FIGURE-09-20-01-991-005-A01
09-20-01Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
STEPA
MAKE SURE AIRCRAFT ISCORRECTLY GROUNDED
STEPB
STEPC
IS THIS STRAIGHTDEBOGGING?
STEPD
IS TETHERING/SHORINGREQUIRED?
STEPE
STEPF
CALCULATE ANTICIPATEDLOADS AND CONFIRM CGLOCATION
GO TO CHART XII( )
GO TO STEP D
YES
NO
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART VI
STABILIZE AIRCRAFT
REMOVE CARGO ANDCATERING EQUIPMENT
GO TO CHART XIV( )
GO TO STEP E
YES
NO
GO TO CHART X( )
GO TO STEP F
YES
NO
STEPG
SEE 03−00−00
SEE 04−30−00
MAKE SURE CG IS CONTROLLED
REMOVE MAJORCOMPONENTS THAT AREDAMAGED OR NECESSARYFOR WEIGHT REDUCTIONOR CG CONTROL
SEE 04−20−00
GO TO STEP B
GO TO STEP C
IS IT NECESSARY TODEFUEL OR TRANSFERFUEL?
SEE 03−50−01
GO TO CHART V( )
GO TO CHART IIA STEP E( )
SEE FIGURE 09−20−01−991−012
SEE FIGURE 09−20−01−991−014
SEE FIGURE 09−20−01−991−016
SEE FIGURE 09−20−01−991−005
SEE FIGURE 09−20−01−991−002
N_AR_092001_1_0060101_01_01
Aircraft Recovery Logic ChartChart VI
FIGURE-09-20-01-991-006-A01
09-20-01Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART VII
SELECT METHOD
SELECT RECOVERY TOOLING *
LIFTING BAGSPNEUMATIC
JACKS CRANECOMBINATIONSTEP−BY−STEP
LOADS AND RECORDCALCULATE EXPECTED
LOAD RECORDSCONTROL CG AND MONITOR
GO TO CHART VIII
CONFIRM SOIL STABILITY INTEGRITY OF LIFTING CONFIRM STRUCTURAL
SEE 06−60−00
SEE 06−10−00
SEE 06−00−00
SEE 03−00−00
SEE 04−50−00 *
( )
POINTS/AREAS *
* : BEFORE CONSIDERING WHICH LEVELING /LIFTING OPTION TO USE YOU MUST MAKE AN ACCURATE WEIGHT AND CG ANALYSIS − THIS WILL GIVE YOU THE OPTIMUM POSTIONS AND LOADS FOR THE LIFTING EQUIPMENT.
PREPARE TO LEVEL/LIFT AIRCRAFT
N_AR_092001_1_0070101_01_00
SEE FIGURE 09−20−01−991−008
Aircraft Recovery Logic ChartChart VII
FIGURE-09-20-01-991-007-A01
09-20-01Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART VIII
AND FOLLOW LIFTINGPROCEDURE
AND FOLLOW LIFTINGPROCEDURE
AND FOLLOW LIFTINGPROCEDURE
AND FOLLOW LIFTINGPROCEDURE
AND FOLLOW LIFTINGPROCEDURE
AND FOLLOW LIFTINGPROCEDURE
FUSELAGEFWD
SECTION
FUSELAGEAFT
SECTION
CONTROL CG WITH BALLAST, FUEL, TETHERING ETC.
SELECT LIFTING ENTRY POINTS
CRANE
: THE INSTALLED BELLY FAIRINGLIMITS SLING/AIRBAG LIFTING POINTS
PNEUMATICLIFTING BAGS
WING JACKPOINT
PNEUMATICLIFTING BAGS
CRANE ANDSLING
PNEUMATICLIFTING BAGS
FWD JACKPOINT
WING
GO TO CHART XV
SEE 06−00−00
SEE 06−30−00SEE 06−60−00
SEE 06−40−00SEE 06−60−00
SEE 06−50−00SEE 06−60−00
SEE 06−40−00SEE 06−60−00
SEE 06−30−00SEE 06−60−00
SEE 06−40−00SEE 06−60−00
( )
CAUTION
PREPARE TO LIFT AIRCRAFT
SEE FIGURE 09−20−01−991−015
AND FOLLOW LIFTINGSEE 06−50−00SEE 06−60−00PROCEDURE
N_AR_092001_1_0080101_01_02
Aircraft Recovery Logic ChartChart VIII
FIGURE-09-20-01-991-008-A01
09-20-01Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
AIRCRAFT BATTERIES
IS THERE OBVIOUS STRUCTURAL DAMAGE AND/OR FUEL LEAKING?
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART IX
IS IT BENEFICIAL TO LEAVEBATTERIES CONNECTED?
DISCONNECT AND ISOLATE
AS SOON AS AIRCRAFT ISSTABILIZED
BATTERIES (REMOVE IF POSSIBLE).
LEAVE BATTERIES
SURE BATTERIE MASTERIS OFF UNLESS IF NEEDED
CONNECTED BUT MAKEDISCONNECT AND
SOON AS AIRCRAFT ISSTABILIZED
ISOLATE BATTERIES, AS
YES
YES
NO
NO
GO TO CHART IIA STEP B( )
N_AR_092001_1_0090101_01_00
SEE FIGURE 09−20−01−991−002
Aircraft Recovery Logic ChartChart VIX
FIGURE-09-20-01-991-009-A01
09-20-01Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART X
GO TO CHART IV STEP B
DEFUEL
CONSIDER LEAVING FUEL ONBOARD FOR CG CONTROL
SERVICEABLENORMAL PRESSURE DEFUEL WITH ALL AIRCRAFT SYSTEMS
SEE 05−40−01
DRAIN REMAINING FUEL
DEFUEL USING AN EXTERNAL WIRING HARNESS (EWH)
1.
2.
3.
FOR DETAILS
SEE 05−40−02
SEE 05−10−00
SEE 05−40−03SEE FIGURE 09−20−01−991−004( )
N_AR_092001_1_0100101_01_01
Aircraft Recovery Logic ChartChart X
FIGURE-09-20-01-991-010-A01
09-20-01Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART XI
WEIGHT AND CG POSITION MANAGEMENT
GET THE REQUIRED DATA TO CALCULATE NRW ANDASSOCIATED CG POSITION
GET OEW (OR DOW) AND ASSOCIATED CG POSITION
CALCULATE EFFECT OF REMAINING FUEL QTY
CALCULATE EFFECT OF REMAINING/ADDED ITEMS
CALCULATE EFFECT OF LARGE COMPONENT MOVEMENT
CALCULATE EFFECT OF REMOVED/MISSING ITEMS
CALCULATE NRW AND ASSOCIATED CG POSITION
GO TO CHART IIB STEP H( )
AND COMPLETEWORKSHEETSSEE 05−30−00
(SEE 09−50−01
AND COMPLETEWORKSHEETS (SEE 09−50−01
AND COMPLETEWORKSHEETS (SEE 09−50−01
AND COMPLETEWORKSHEETS (SEE 09−50−01
SEE 03−50−01
AND COMPLETEWORKSHEETS (SEE 09−50−01
SEE 03−00−00
SEE 03−50−01
SEE 03−50−01
SEE 03−50−01
)
)
)
)
)
N_AR_092001_1_0110101_01_00
SEE FIGURE 09−20−01−991−002
Aircraft Recovery Logic ChartChart XI
FIGURE-09-20-01-991-011-A01
09-20-01Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART XII
SEE 07−20−00
SEE 07−40−00
DEBOGGING
CONFIRM WEIGHT AND CG LOCATION
CONFIRM NO FUEL LEAKS AND ALL LANDING GEARS INTACT
MAKE AIRCRAFT AS LIGHT AS PRACTICAL
WILL SOIL REQUIRE STABILIZING?
CONFIRM NOROADWAYPREPARATIONREQUIRED
PREPARE ROADWAY USINGGRAVEL, STEEL PLATES,PLYWOOD OR MATS ASNECESSARY
EXCAVATE AREA AROUNDLANDING GEAR
PREPARE TO TOW OR WINCHAIRCRAFT
GO TO CHART XV STEP A
SEE 03−00−00
CONSULT AIRPORT AUTHORITY FOR RECENT EXCAVATIONS
CONFIRM SOIL STABILITY USING APPROPRIATE METHOD
NO YES
( )SEE FIGURE 09−20−01−991−015
N_AR_092001_1_0120101_01_01
SEE 07−30−00
Aircraft Recovery Logic ChartChart XII
FIGURE-09-20-01-991-012-A01
09-20-01Page 15
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART XIII
LANDING GEAR
SEE 02−30−01
5
4
3
2
1 NLG RETRACTED, COLLAPSED OR MISSING
ONE MLG RETRACTED,
INSTALL LANDING GEARLOCKS
COLLAPSED OR MISSING
ALL LG RETRACTED, COLLAPSED OR MISSING
ALL MLG RETRACTED,COLLAPSED OR MISSING
NLG AND ONE MLGRETRACTED, COLLAPSED OR MISSING
CONFIRM LANDING GEARSECURE
GO TO CHART IIA STEP F( )
GO TO CHART IIA STEP F( )
SEE 06−60−01
SEE 06−60−03
SEE 06−60−02
SEE 06−60−04
SEE 06−60−05
YESNOARE ALL LANDING GEARS DOWN AND LOCKED?
N_AR_092001_1_0130101_01_00
SEE FIGURE 09−20−01−991−002
SEE FIGURE 09−20−01−991−002
Aircraft Recovery Logic ChartChart XIII
FIGURE-09-20-01-991-013-A01
09-20-01Page 16
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART XIV
TETHERING / SHORING
FORDETAILS
ATTACH TETHERS TODOORWAYSFIXTURES, FLAPBEAMS AND LANDINGGEAR
PREPARE SHORING IF REQUIRED
SELECT APPROPRIATE TETHERCABLES
ATTACH FITTINGS TOAIRCRAFT
INSTALL GROUND ANCHORS
INSTALL TENSIONING DEVICESMONITOR AND RECORD LOADS
ARE TETHERING FITTINGS AVAILABLE?
GO TO CHART VI STEP E( )
SEE 04−30−00 SEE 04−30−00
SEE 04−30−00
NO YES
N_AR_092001_1_0140101_01_00
SEE FIGURE 09−20−01−991−006
Aircraft Recovery Logic ChartChart XIV
FIGURE-09-20-01-991-014-A01
09-20-01Page 17
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
YES "A" ARE ALL LANDING GEARSSERVICEABLE?
NOTE: THE CHARTS ARE NOT IN A CHRONOLOGICAL SEQUENCE FOR A RECOVERY.
CHART XVTOWING
CALCULATE PROJECTED LOADS
ATTACH SHACKLES TO MAINLANDING GEAR TOW LUGS
PREPARE AND ATTACH CABLESFOR TOWING AND WINCHING
ARRANGE PULLEY IF REQUIRED
ATTACH DYNAMOMETER TOCABLE SYSTEM
USE APPROPRIATE MEANS TO STEER NOSE GEAR
PULL AIRCRAFT STEADILY BACKON TO HARD SURFACE
RECORD BREAK−AWAY ANDPULLING FORCES FROM
DYNAMOMETER
FOR DETAILS ON MOVINGAIRCRAFT
MOVE AIRCRAFT TOINSPECTION FACILITY
MAKE SURE SITE RETURNEDTO NORMAL
PREPARE REPORT
SEE 07−40−04
SEE 08−00−00END
NO "B"
SEE 07−60−00
SEE 07−40−00
N_AR_092001_1_0150101_01_01
Aircraft Recovery Logic ChartChart XV
FIGURE-09-20-01-991-015-A01
09-20-01Page 18
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-20-01-004-A01
Airline Aircraft Recovery Process Document
1. Airlines should consider the preparation of an internal Aircraft Recovery Process Document. Thisdocument will help the airline to prepare for an aircraft recovery, because it will contain fullinstructions about how to organize and prepare for a good recovery.It must give the steps on how each airline can do an aircraft recovery, from the time an incident isnotified, to the movement of the aircraft to an inspection or repair facility.Help to prepare a process document of this type is available if you contact the IATA AircraftRecovery Working Group at the website that follows:- http://www.iata.org
NOTE : This chapter gives references to web sites for information only. Airbus shall not be heldliable for web site or document content and for update or change of addresses.
A. Proposed Coverage
(1) The goals of the Aircraft Recovery Team, these should be clearly stated. Some ideas toinclude are:- How the Recovery Team can react,- What authority the Recovery Team has,- The promotion of aircraft recovery awareness,- How to share aircraft recovery data with the manufacturer, other operators and special
interested groups,- Coordination of resources.
(2) A current and up-to-date list of the Recovery Team Managers and Recovery TeamLeaders.This must include office, home, fax, pager and cell phone numbers. The same informationshould be available for all other members of the recovery team.
(3) A list of applicable aircraft to recover by the Recovery Team.This could include aircraft owned or leased by the airline and aircraft from subsidiaryairlines and/or contracted airlines.
(4) Procedures to follow when there is a known incident.These must highlight the need to keep and record all important data.
(5) Current list of applicable government agencies with contact numbers.
(6) How each team member can prepare.This must include suggestions on what items of clothing and equipment should beavailable in a personal ”go kit”. Vaccinations and visas should also be done.
(7) A full list of airline support staff and contact numbers.This should include structural and power plant engineering staff, tooling and equipmenttechnicians, weight and balance, purchasing and logistic personnel.
09-20-01Page 19
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(8) A current and full list of all company-owned aircraft recovery equipment.This should include the location, size and weight of all containers in where the equipmentis stored.
(9) A current copy of the IATP D/E pools ground handling equipment, ground maintenanceequipment and aircraft recovery kits.These data are now available at the website that follows:- http://www.iatp.com
NOTE : IATP website and recovery kits are available for IATP members only.
NOTE : This chapter gives references to web sites for information only. Airbus shall notbe held liable for web site or document content and for update or change ofaddresses.
(10) A list of the local availability of general aircraft recovery materials and equipment. made bythe company.This list should include materials and equipment such as plywood and steel sheets, crushedrock, cribbing, cranes, heavy equipment etc.You can be prepare this list with the ICAO Removal of disabled aircraft Document 9137-AN/898 as a guide.
(11) An Aircraft Recovery Manual (ARM) for each fleet type operated and its storage locations.
(12) The size of the cargo doors of each fleet type operated.This will helps to move equipment if the incident is at a different airport.
(13) A list of all company-owned tooling, that includes recovery tooling such as pneumaticlifting bags, jacks, slings, etc.This can include their location and properties such as capacity, compressed and extendedheights, arc movement capability, etc.
09-20-01Page 20
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-20-01-005-A01
Off Runway Incident Reporting Proforma
1. GeneralThis ”Off-Runway” Incident Form is designed to support the evaluation of ”off runway” in-serviceincidents. It helps to make technical judgement and to decide the quickest disposition of actionsnecessary to return the aircraft landing gear to service.
09-20-01Page 21
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WH
ICH
RE
QU
IRE
IND
IVID
UA
L A
SS
ES
SM
EN
T A
ND
DIS
PO
SIT
ION
.
MA
KE
TE
CH
NIC
AL
JUD
GE
ME
NT
AN
D T
O D
EC
IDE
TH
E Q
UIC
KE
ST
DIS
PO
SIT
ION
OF
AC
TIO
NS
NE
CE
SS
AR
Y T
O R
ET
UR
N T
HE
AIR
CR
AF
T L
AN
DIN
G G
EA
R T
O S
ER
VIC
E.
FIL
L IN
ALL
SE
CT
ION
S A
S F
ULL
Y A
S P
OS
SIB
LE A
ND
SU
PP
LY A
S M
AN
YP
HO
TO
GR
AP
HS
AS
PO
SS
IBLE
TO
SH
OW
TH
E IN
CID
EN
T
AIR
LIN
E
DA
TE
AN
D (
LOC
AL)
TIM
E O
F IN
CID
EN
T
AIR
PO
RT
AIR
CR
AF
T T
YP
E IN
CLU
DIN
G D
AS
H N
UM
BE
R
AIR
CR
AF
T R
EG
IST
RA
TIO
N
MS
N
TH
IS "
OF
F−
RU
NW
AY
" IN
CID
EN
T F
OR
M IS
DE
SIG
NE
D T
O S
UP
PO
RT
TH
EE
VA
LUA
TIO
N O
F "
OF
F−
RU
NW
AY
" IN
−S
ER
VIC
E IN
CID
EN
TS
. IT
HE
LPS
TO
EA
CH
"O
FF
−R
UN
WA
Y"
INC
IDE
NT
CO
MP
RIS
ES
UN
IQU
E C
IRC
UM
ST
AN
CE
S
N_A
R_0
9200
1_1_
0200
101_
01_0
0
Off Runway ProformaIntroduction (Sheet 1 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 22
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
SU
PP
LY P
HO
TO
GR
AP
HS
TO
SH
OW
TH
E IN
CID
EN
T. T
HE
SE
MU
ST
INC
LUD
E V
IEW
S O
F T
HE
TA
XIW
AY
, RU
NW
AY
,A
IRP
OR
T, B
UIL
DIN
GS
AN
D T
HE
PO
SIT
ION
S O
F A
LL O
BS
TA
CLE
S T
HA
T T
HE
AIR
CR
AF
T T
OU
CH
ED
DU
RIN
G T
HE
INC
IDE
NT
. YO
U M
US
T A
LSO
SH
OW
TH
E P
AT
H O
F T
HE
LA
ND
ING
GE
AR
. SH
OW
TH
E C
RO
SS
SE
CT
ION
OF
TH
E R
UN
WA
YA
ND
TH
E A
DJA
CE
NT
GR
OU
ND
TH
AT
TH
E A
IRC
RA
FT
MO
VE
D A
CR
OS
S, W
ITH
TH
E A
PP
RO
XIM
AT
E D
IME
NS
ION
S O
F A
LLS
TE
PS
AN
D G
RA
DIE
NT
S.
GIV
E T
HE
AP
PR
OX
IMA
TE
DIS
TA
NC
ES
AN
D T
RA
JEC
TO
RY
OF
TH
E A
IRC
RA
FT
DU
RIN
G T
HE
INC
IDE
NT
, WIT
H T
HE
AT
TIT
UD
E O
F T
HE
AIR
CR
AF
T A
FT
ER
TH
E IN
CID
EN
T.
SU
PP
LY P
HO
TO
S T
O S
HO
W T
HE
ITE
MS
BE
LOW
:
− T
HE
AP
PLI
CA
BLE
LA
ND
ING
GE
AR
(T
HE
TW
O S
IDE
S, F
RO
NT
, RE
AR
ELE
VA
TIO
NS
AN
D A
LL A
RE
AS
OF
DA
MA
GE
)B
EF
OR
E A
ND
AF
TE
R R
EC
OV
ER
Y−
TH
E A
IRC
RA
FT
BE
FO
RE
RE
CO
VE
RY
IN IT
S R
ES
T P
OS
ITIO
N O
FF
TH
E R
UN
WA
Y.
− T
HE
TR
AC
KS
MA
DE
BY
EA
CH
LA
ND
ING
GE
AR
OF
F T
HE
RU
NW
AY
AN
D A
LL S
KID
MA
RK
S O
N T
HE
RU
NW
AY
− R
EC
OV
ER
Y O
F T
HE
AIR
CR
AF
T
SE
CT
ION
1
A
N_A
R_0
9200
1_1_
0200
102_
01_0
0
Off Runway ProformaSection 1 (Sheet 2 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 23
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DE
TA
ILE
D W
RIT
TE
N D
ES
CR
IPT
ION
OF
"O
FF
−R
UN
WA
Y"
INC
IDE
NT
SE
CT
ION
2
N_A
R_0
9200
1_1_
0200
103_
01_0
0
Off Runway ProformaSection 2 (Sheet 3 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 24
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WIN
D D
IRE
CT
ION
AN
D S
PE
ED
AT
TIM
E O
F IN
CID
EN
T
SE
CT
ION
3
10 K
NO
TS
RU
NW
AY
N_A
R_0
9200
1_1_
0200
104_
01_0
0
Off Runway ProformaSection 3 (Sheet 4 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 25
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
SE
CT
ION
4 −
ME
TR
ICS
(A)
AP
PR
OX
IMA
TE
AIR
CR
AF
T W
EIG
HT
(B)
AIR
CR
AF
T C
EN
TE
R O
F G
RA
VIT
Y
(C)
FLI
GH
T P
HA
SE
OF
AIR
CR
AF
T A
T T
IME
OF
INC
IDE
NT
−T
ICK
AP
PR
OP
RIA
TE
PH
AS
E
LOW
SP
EE
D T
AX
IING
/ M
AN
EU
VE
RIN
G
TO
UC
H D
OW
N
(D)
DIS
TA
NC
E R
UN
OF
F R
UN
WA
Y B
Y E
AC
H G
EA
R (
I.E. T
RA
CK
LE
NG
TH
MA
DE
BY
EA
CH
GE
AR
).
NLG
OR
(E)
AP
PR
OX
IMA
TE
AIR
CR
AF
T G
RO
UN
D S
PE
ED
AS
FU
NC
TIO
N O
F IN
CID
EN
T T
IME
AT
BE
GIN
NIN
G O
F IN
CID
EN
T
TIM
E F
RO
M S
TA
RT
OF
INC
IDE
NT
(F
IRS
T G
EA
R O
FF
RU
NW
AY
) T
O A
IRC
RA
FT
AT
RE
ST
EV
ALU
AT
E A
T T
HE
TIM
E O
F S
UC
H A
N E
VE
NT
(F)
RU
NW
AY
/ T
AX
IWA
Y S
UR
FA
CE
CO
ND
ITIO
N−
TIC
K A
S A
PP
RO
PR
IAT
E
DR
Y
ME
TR
IC T
ON
NE
S O
RIM
PE
RIA
L T
ON
S
%M
AC
FE
ET
FR
OM
CE
NT
ER
LIN
E O
R
ME
TE
RS
FR
OM
CE
NT
ER
LIN
E O
R
HIG
H S
PE
ED
TA
XIIN
G−
TA
KE
−O
FF
HIG
H S
PE
ED
TA
XIIN
G−
LAN
DIN
G
TO
WIN
G (
WIT
H T
OW
BA
R)
TO
WIN
G (
TO
WB
AR
LES
S)
OT
HE
R
RH
MLG
LHM
LG
KN
OT
SA
T E
ND
OF
INC
IDE
NT
KN
OT
S SE
CO
ND
S D
IFF
ICU
LT T
O
DA
MP
WE
TF
LOO
DE
DS
NO
WIC
EO
TH
ER
ME
TE
RS
ME
TE
RS
ME
TE
RS
NLG
RH
MLG
LHM
LGF
EE
TF
EE
TF
EE
T
N_A
R_0
9200
1_1_
0200
105_
01_0
0
Off Runway ProformaSection 4-1 (Sheet 5 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 26
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
(G)
OF
F−
RU
NW
AY
SU
RF
AC
E N
AT
UR
E A
ND
CO
ND
ITIO
NS
: TIC
K O
R S
PE
CIF
Y A
S A
PP
RO
PR
IAT
E
(1)
TY
PE
OF
GR
OU
ND
−
(2)
NA
TU
RE
OF
SU
RF
AC
E −
(3)
CO
ND
ITIO
N O
F G
RO
UN
D −
HA
RD
(4)
WE
AT
HE
R C
ON
DIT
ION
S A
T T
IME
OF
INC
IDE
NT
− P
LEA
SE
GIV
E D
ET
AIL
S
(5)
VIS
IBIL
ITY
−
(H)
WE
RE
AN
Y O
BS
TA
CLE
S T
OU
CH
ED
DU
RIN
G T
HE
INC
IDE
NT
− P
LEA
SE
TIC
K A
S A
PP
RO
PR
IAT
E.
NO
NE
SU
PP
LY D
RA
WIN
G O
R P
HO
TO
GR
AP
H A
ND
AP
PR
OX
IMA
TE
DIM
EN
SIO
NS
OF
AN
Y O
BS
TA
CLE
S R
UN
OV
ER
OT
HE
RS
TO
NY
CLA
Y
SO
FT
WA
TE
R L
OG
GE
DO
TH
ER
DA
YN
IGH
TV
ISIB
ILIT
YM
ET
ER
S
RU
NW
AY
LIG
HT
SK
ER
B S
TO
NE
DR
AIN
AG
E C
HA
NN
ELS
HO
LES
, BU
RR
OW
FLA
TU
ND
ULA
TIN
GS
TE
PP
ED
/BA
NK
ED
OT
HE
R
SA
ND
DR
YW
ET
FLO
OD
ED
SN
OW
ICE
RO
CK
S
OT
HE
R
N_A
R_0
9200
1_1_
0200
106_
01_0
0
Off Runway ProformaSection 4-2 (Sheet 6 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 27
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
(I)
BR
AK
ING
AP
PLI
CA
TIO
N
IF Y
ES
, AT
WH
AT
PO
INT
IN T
HE
INC
IDE
NT
WE
RE
TH
E B
RA
KE
S A
PP
LIE
D
AP
PR
OX
IMA
TE
LE
NG
TH
OF
ON
−R
UN
WA
Y A
ND
OF
F−
RU
NW
AY
SK
ID M
AR
KS
IF A
PP
LIC
AB
LE:
(J)
WE
RE
TH
RU
ST
RE
VE
RS
ER
S D
EP
LOY
ED
DU
RIN
G IN
CID
EN
T
(K)
AP
PR
OX
IMA
TE
AIR
CR
AF
T V
ELO
CIT
Y IN
3 A
XE
S
VE
RT
ICA
L
(L)
NLG
ST
EE
RIN
G A
NG
LE (
FU
NC
TIO
N O
F T
IME
IF P
OS
SIB
LE)
(M)
EN
GIN
E T
HR
US
T,
WE
RE
BR
AK
ES
AP
PLI
ED
DU
RIN
G T
HE
INC
IDE
NT
PLE
AS
E S
UP
PLY
PH
OT
OG
RA
PH
S O
F S
KID
MA
RK
S IF
AP
PLI
CA
BLE
ON
−R
UN
WA
Y S
KID
MA
RK
DIS
TA
NC
EM
ET
ER
SO
RF
EE
T
OF
F−
RU
NW
AY
SK
ID M
AR
K D
IST
AN
CE
ME
TE
RS
OR
FE
ET
YE
SN
O
m/s
FO
RW
AR
DLA
TE
RA
Lm
/sm
/s
OR
VE
RT
ICA
Lft/
sF
OR
WA
RD
LAT
ER
AL
ft/s
ft/s
ST
AR
TF
INIS
H°
°
MA
X D
EV
IAT
ION
OF
NO
SE
WH
EE
L S
TE
ER
ING
AN
GLE
RE
LAT
ED
TO
DIR
EC
TIO
N O
F T
RA
VE
L.D
UR
ING
OF
F−
RU
NW
AY
TR
AJE
CT
OR
Y°
AT
RE
ST
°
AT
RE
ST
0%5%
10%
OT
HE
R%
DU
RIN
G O
FF
−R
UN
WA
Y T
RA
JEC
TO
RY
0%5%
10%
OT
HE
R%
(N)
RE
ST
ING
AT
TIT
UD
E O
F A
IRC
RA
FT
OF
F R
UN
WA
YR
OLL
PO
RT
OR
ST
AR
BO
AR
D
PIT
CH
NO
SE
DO
WN
OR
NO
SE
UP
° °
YE
SN
O
SA
ME
CO
MM
EN
T A
S A
BO
VE
N_A
R_0
9200
1_1_
0200
107_
01_0
0
Off Runway ProformaSection 4-3 (Sheet 7 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 28
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DE
PT
H A
ND
NU
MB
ER
OF
WH
EE
LS IN
GR
OU
ND
: EN
TE
R V
ALU
ES
IN T
AB
LE.
SE
CT
ION
5
MA
RK
WH
EE
LS T
HA
T R
UN
OF
F−
RU
NW
AY
WIT
H A
CR
OS
S IN
TH
E D
IAG
RA
MB
ELO
W, E
.G.
1 2 3 4 5 6 87 9 10
mm
mm
inin
AT
TIT
UD
EO
FF
RU
NW
AY
DE
PT
H IN
GR
OU
ND
513 7
624 8
IN R
ES
TIN
GD
UR
ING
RU
NW
HE
EL
910
NO
TE
: A32
0 O
NLY
− O
PT
ION
AL
01
01
01 01 01 01
01
N_A
R_0
9200
1_1_
0200
108_
01_0
0
Off Runway ProformaSection 5 (Sheet 8 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 29
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DE
SC
RIP
TIO
N O
F T
NE
RE
CO
VE
RY
(S
UP
PLY
PH
OT
OG
RA
PH
S):
SE
CT
ION
6
N_A
R_0
9200
1_1_
0200
109_
01_0
0
Off Runway ProformaSection 6 (Sheet 9 of 9)
FIGURE-09-20-01-991-020-A01
09-20-01Page 30
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TASK 09-20-01-869-801-A01
IATA Aircraft Recovery Quick Reference Check List
1. GeneralThis guide was prepared and given by the IATA Aircraft Recovery Working Group. It is a generalguide and for use as a checklist during an aircraft recovery incident.
2. InspectionsNot Applicable.
3. Job Setup ReferencesNot Applicable.
4. Procedure
Subtask 09-20-01-869-001-A01
A. Before you are on the site
(1) Get the initial information about the incident.
(2) Contact local airline/agent/own representative.
(3) Prepare and make a selection of personnel/equipment/manuals.
(4) Check availability of IATP-kits and order if necessary.
NOTE : IATP website and recovery kits are available for IATP members only.
Subtask 09-20-01-869-002-A01
B. When you are on the site
(1) Make necessary contact with local security/fire fighting brigade to secure the site, and givearea map.
(2) Give careful instructions for an aircraft recovery plan.
(3) Get necessary approval from local authorities to start the recovery operation.
(4) Make sure:
(a) Communication to/from site works correctly,
(b) Transportation to/from site is possible,
(c) Necessary accommodation and facilities can be available on site.
(5) Contact local airlines, airport authorities and local suppliers for help with.
(a) Heavy machinery/cranes, etc.
(b) Access roads, building materials.
(c) Timber/gravel/sand/steel plates, etc.
09-20-01Page 31
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
(d) Lighting equipment.
(6) Remove all necessary weight possible from the aircraft if needed.
(a) Make sure there are documents on restricted articles and hazardous material.
(b) Remove fuel and liquids if possible.
(c) Remove baggage and cargo if possible.
(d) Remove all unwanted and discarded material from the galleys and lavatories.
(7) Calculate the aircraft weight and CG.
(8) Make sure the recovery plan is still valid and all safety precautions have been taken.
(9) Remove all necessary aircraft components if needed.
(a) To lighten aircraft,
(b) To keep wind-induced loads to a minimum,
(c) To observe instructions from local authorities.
(10) Make preparation for
(a) Tethering/Shoring.
(b) Leveling/Lifting.
(c) Moving the aircraft.
(11) Prepare to put the aircraft in a hangar or to park it.
09-20-01Page 32
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-20-02 RECOVERY TEAM
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-20-02-001-A01
Composition of the Recovery Team
1. GeneralAirbus recommends that each airline:- Prepare an internal Aircraft Recovery Process document (see DESC 09-20-01-004-A01).- Make an Aircraft Recovery Team, with reference to this document.For this team, it is recommended:- To take the volunteers from the aircraft maintenance branch. These volunteers should have a
strong interest in the aircraft recovery process and a good technical background.- That the members of the Aircraft Recovery Team stay a part of the team (even when they have
promotions or move to different internal departments) so that their experience is not lost.
2. The ManagerAirbus recommends that each Aircraft Recovery Team have a manager to control the activities of theAircraft Recovery Team and any aircraft recovery incidents.
A. The Manager should have:- Experience as an Aircraft Maintenance Production Manager with the related responsibilities,- Experience and/or knowledge related to aircraft recovery.
B. The Manager should:- Supervise the Aircraft Recovery Team and their related activities,- Organize regular meetings and exercises with the Aircraft Recovery Team,- Be the interface with the airport, local and state authorities for aircraft recovery,- Represent his airline, on the International Airline Transport Association’s (IATA), Aircraft
Recovery Working Group (ARWG) and the International Airline Technical Pool (IATP)related to aircraft recovery.
3. Team LeadersDepending on the size of the airline, there can be one or more Team Leaders.
A. The Team Leaders should have:- Experience as an Aircraft Maintenance Production Team Leader or Foreman,- Good technical and leadership qualities,- Experience and/or knowledge of aircraft recovery,- Good knowledge of jacks, pneumatic lifting bags and cranes.
B. The Team Leaders should:- Report to the Aircraft Recovery Manager,- Control the company-owned aircraft recovery equipment and make sure that it is always
serviceable,
09-20-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
- Make recommendations and suggestions related to the purchase of aircraft recoveryequipment,
- Supervise the on-site aircraft recovery steps.
4. Structures Engineer and Systems EngineerThe Structure Engineer and Systems Engineer should:- Analyze damage to the aircraft,- Prepare the drawings necessary for temporary repairs,- Help the Recovery Manager and Team Leader with decisions related to aircraft recovery.
5. Planner or Purchasing AgentThe Planner or Purchasing Agent should:- Know how to get access to the nearest aircraft recovery kit,- Have contact information for local heavy equipment operators,- Know where to get general aircraft recovery materials,- Organize the leasing of equipment when necessary.
6. Licensed Aircraft TechniciansThe Licensed Aircraft Technicians should:- Have good technical knowledge,- Have a valid aircraft maintenance license for the specific aircraft type.- Report to the Aircraft Recovery Team Leader,- Do the specific aircraft maintenance tasks assigned by the Team Leader.
09-20-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-30-01 AIRCRAFT RECOVERY EQUIPMENT TOOLING AND MATERIALS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-30-01-001-A01
General
1. GeneralIt can be necessary for operators to use tools during the recovery process.There are two categories of aircraft recovery tooling and equipment:- General recovery equipment- Specialized recovery equipmentYou can get these tools at the airport (contact the Airport Authorities or IATP if you are a member),or locally (contact local vendors).
2. General Materials, Equipment and ToolingThe general materials, equipment and tooling that follow are usually available locally (this is not afull list) :- Work lights, floodlights,- Ballast bags,- Sheets of plywood, steel plate, planking, etc.,- Cribbing timber (railroad ties) to make platforms,- Stones, gravel, broken asphalt to be compacted to make roadways,- Trailers and padded materials (mattresses, rubber padding, tires, sandbags) to move damaged
aircraft,- Bulldozers, forklifts, crane, winching vehicles, excavators,- Towing tractor,- Cables, ropes, pulley blocks, ladders,- Mobile shelter-trailer, commercial transport equipment,- Wooden/steel beams,- Flatbed trucks and trailers,- Pumps, hoses and storage for fuel and/or water,- Hand pump for manual doors opening/closing,- On-site communication equipment (telephones, faxes, interphone headsets),An electrical or air power supply can be necessary for some of these tools. Thus, other equipment canbe necessary:- Mobile electrical power unit (min. 5 kW),- Mobile air power unit (min. 7 bar (102 psi)).
NOTE : The ICAO Airport Services Manual, part 5, Document 9137-AN/898, ”Removal of DisabledAircraft” gives a list of recommended materials and equipment.
3. Lifting and Tethering MaterialThe general materials, equipment and tooling that follow will be useful for the lifting and tethering ofthe aircraft.
09-30-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
A. Slings/straps - Nylon, Dacron, Carbon FiberThese slings/straps are moisture and mildew resistant. As they dry quickly, it is possible to putthem into storage a short time after use.You can get them in almost all widths and lengths with different end attachments. You can getnylon straps/slings with single or double strength with single or multiple bands.All these slings/straps help prevent damage to the aircraft skins when you lift the aircraft atareas such as the forward fuselage. But it is important to protect the straps from sharp edgesand small radiuses.Make sure that the slings/strap has a label, which gives the rate loads.Do an inspection of the straps before you use them.
B. Wire RopeUsually, a 6X19 type rope made from improved plow strength steel can be used for recoveryoperations.
C. ChainAll types of hoisting chains made from good quality material will give very good results.
D. Rope - Manila, Nylon, PolypropyleneThese are good general-purpose ropes but they are not recommended for lifting or tetheringtasks.
09-30-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-30-01-002-A01
Airbus Specific Recovery Tools
1. For the wing lifting procedure using cranes (see 06-50-00), Airbus developed a specific tool, seeTABLE 1.
TOOL - DESCRIPTION (PART NUMBER) QTY VENDOR
7K804427D520 CRANE ATTACHMENT - WINGLIFTING BRACKET
2
Airbus Specific Recovery Tools
TABLE 1
09-30-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-30-02 AIRCRAFT RECOVERY TOOLING
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-30-02-001-A01
General
1. Table 1 gives the list of tools referenced in the ARM.
NOTE : Any comparable equipment may be used provided that it satisfies the requirements of theprocedure. Other conventional suppliers of recovery material can provide items of the kitsset.
09-30-02Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
PART NUMBER NOMENCLATURE VENDOR/SUPPLIER REFERENCES
460005833 GROUND LOCK SLEEVE TASK 02-30-01-481-801-A01
460005835 GROUND LOCK SLEEVE TASK 02-30-01-481-801-A01
460007280 SLEEVE-GROUNDLOCK TASK 02-30-01-481-801-A01
7K804427D520 CRANE ATTACHMENT - WING LIFTING BRACKET TASK 06-50-00-581-802-A01DESC 09-30-01-002-A01
97A28002117002 PURGING TOOL TASK 05-40-02-650-801-A01
98A09003000001 BAR-STEERING, NOSE WHEEL TASK 07-40-02-584-802-A01
98A28104000000 PURGER WATER DRAIN TASK 03-20-02-970-801-A01
98A28104000002 TOOL - PURGING TASK 05-40-02-650-801-A01
98A28203000000 TEST EQUIPMENT JET PUMP TASK 05-40-02-650-801-A01
98D07103000000 DYNAMOMETER - SAFETY STAY TASK 06-30-00-581-802-A01
98D07103500000 JACK ADAPTER - FUSELAGE TASK 06-30-00-581-802-A01
98D07104081000 JACKING PAD SET (A321) TASK 06-30-00-581-802-A01
98D07203000 MOORING FITTING DESC 04-30-00-001-A01TASK06-50-00-581-803-A01
09-30-02Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
PART NUMBER NOMENCLATURE VENDOR/SUPPLIER REFERENCES
98D07203003 FUSELAGE SHORING CRADLE TASK 06-50-00-581-801-A01
98D09104000001 ATTACHMENT - TOWING TASK 07-40-02-584-801-A01
98D09104001000 ATTACHEMENT-TOWING TASK 07-40-02-584-802-A01
98D09104002000 ATTACHMENT - TOWING (OPTIONAL 4 WHEELBOGIE MLG)
TASK 07-40-02-584-802-A01TASK07-40-02-584-801-A01
98D10203500 MOORING KIT - NLG TASK 04-30-00-556-801-A01
98D104000001 JACKING PAD SET (A318, A319, A320) TASK 06-30-00-581-802-A01
98D32203502000 SAFETY PIN - NLG DOOR TASK 02-30-01-481-801-A01
98D57004031 WING SHORING CRADLE TASK 06-50-00-581-801-A01
98F09103500000 CABLE-TOWING, MLG TASK 07-40-02-584-802-A01TASK07-40-02-584-801-A01
D23080000 PIN-GROUND LOCK, NLG TASK 02-30-01-481-801-A01
D23156000 PIN-SAFETY TASK 07-40-02-584-802-A01TASK07-40-01-584-802-A01TASK07-40-02-584-801-A01TASK07-40-01-584-801-A01
09-30-02Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
PART NUMBER NOMENCLATURE VENDOR/SUPPLIER REFERENCES
DAH602734 GROUND LOCK SLEEVE TASK 02-30-01-481-801-A01
DRT68031 SLEEVE - GROUND LOCK TASK 02-30-01-481-801-A01
DRT68923 SLEEVE-GROUND LOCK TASK 02-30-01-481-801-A01
GSE WHEEL CHANGE JACK TASK 02-30-01-867-802-A01
MZ23080000 PIN - NLG DOWNLOCK SAFETY TASK 02-30-01-481-801-A01
TMHCP07-00-00 WHEEL CHANGE AXLE JACK TASK 02-30-01-867-802-A01
Tools and Equipment
TABLE 1
09-30-02Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-30-03 IATP AIRCRAFT RECOVERY KITS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-30-03-001-A01
General
1. IATP Recovery KitsThe International Airline Technical Pool provides a number of aircraft recovery kits at strategiclocations around the world.Currently, there are ten of these kits and they are maintained by provider airlines.
NOTE : The kits are also available on a rental basis to non-member operators.Information on kits content, purpose, capability, providers locations etc. should be available from:- http://www.iatp.com
NOTE : IATP website and recovery kits are available for IATP members only.
NOTE : This chapter gives references to web sites for information only. Airbus shall not be heldliable for web site or document content and for update or change of addresses.
2. Location of the Main KitsCurrent locations of the IATP kits and their provider are given in TABLE 1:
London, England LHR British Airways
Paris, France ORY Air France
Johannesbourg, South Africa JNB South African Airways
Tokyo, Japan NRT Japan Airlines
New York, USA JFK Delta Airlines
Chicago, USA ORD American Airlines
Los Angeles, USA LAX American Airlines
Honolulu, USA HNL United Airlines
Sydney, Australia SYD Qantas Airlines
Mumbai, India BOM Air India
IATP Recovery Kits
TABLE 1
The TABLE 2 gives details on kit suppliers and contacts.
09-30-03Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
COMPANY CODE KITLOCATION
GIVENNAME
FAMILYNAME
SITACODE
MAILINGADDRESS
AmericanAirlines
AA LAXORD
Julie McClain HDQTPAA American Airlines3800 N. Mingo Rd. MD523Tulsa OK 74158
Air France AF ORY Philippe Guillem ORYJOAF Air FranceOrly Sud 124F-94396 Orly AerogareCedex
Air India AI BOM KG Shekar BOMELAI Air India Line Stations,Engineering DeptOld AirportKALINA MAHARASTRA400029 INDIA
BritishAirways
BA LHR Brian Deacon LHRKEBA British Airways PLCBA Maintrol3rd Floor Europe HouseWaterside, PO Box 365HARMONDSWORTHWEST DRAYTON UB70GB
DeltaAirlines
DL JFK Terry Lucas ATLTEDL Delta AirlinesP.O. BOX 20706ATLANTA GA 30320 USA
JapanAirlines
JL NRT Satoru Arasaki TYOJPJL Japan Airlines3-5-1, HANEDAAIRPORTM1 BLDGOTA-KU TOKYO144-0041
Qantas QF SYD Jean-Marie
L’Eveille SYDEDQF Qantas Airways LtdSydneyDistribution CenterSYDSDC/1263-271 Coward RoadMascot N.S.W 2020AUSTRALIA
09-30-03Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
COMPANY CODE KITLOCATION
GIVENNAME
FAMILYNAME
SITACODE
MAILINGADDRESS
SouthAfrican
SA JNB Charlie Haman JNBMPSA South AfricanSouth Africa AirwaysTechnicalTechnical AreaJOHANNESBURGInternational Airport
UnitedAirlines
UA HNL Connie Showalter SFOPSUA United AirlinesS.F. Maintenance Base -SFOUSSan Fransisco InternationalAirportSAN FRANSISCO CA94128 USA
Kit Suppliers and Contacts
TABLE 2
09-30-03Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-30-03-002-A01
Example of IATP Recovery Kit
1. This section gives an example of an IATP recovery kit that can be found at main airports. It is onlyan example and does not reflect the exact content of all main IATP kits.TABLE 1 gives an example of basic recovery kit.TABLE 2 gives an example of supplementary kit.
Quantity Description
90 PNEUMATIC BAGS (SINGLE ELEMENT)
1 MASTER CONTROL CONSOLE5 REMOTE CONTROL CONSOLE5 AIR DISTRIBUTORS6 MANIFOLD (CONTROL CONSOLE)
85 PNEUMATIC HOSES6 WINCHES6 WIRE ROPES6 EARTH ANCHORS16 PLASTIC FOAM PROTECTION PADS (50 mm (2 in) thick)
1 ROLL POLYTHENE SHEET (500 gauge, 7.3 m (287 in) wide)
1 AIR COMPRESSOR2 REGENT TRIPOD CRASH JACKS
Capacity - 710 mm (28 in) to 1730 mm (68 in), 80 tonsCapacity - 1730 mm (68 in) to 3560 mm (140 in), 100 tons
1 COMPRESSOR SPARES AND BAG REPAIR KIT
Basic Recovery Kit
TABLE 1
Quantity Description
2 PNEUMATIC BAGS2 PNEUMATIC HOSE REELS4 MANIFOLD CONTROL CONSOLE / AIR CONTROL CONSOLE WITH 10
OUTLETS4 PROTECTION PADS4 WIRE ROPE (CAPACITY OF TOWING A CODE E/F AIRCRAFT)
2 BODY LIFTING SLING (CAPACITY OF LIFTING A CODE E/F AIRCRAFT )
1 AIR COMPRESSOR (FOR SYNCRO JACKS)
2 SPREADER BARS (INCLUDES SLINGS AND SHACKLES)
09-30-03Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
Quantity Description
1 AIR COMPRESSOR
Supplementary Recovery Kit
TABLE 2
09-30-03Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
09-50-01 WEIGHT AND CG CALCULATION WORKSHEETS
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
DESC 09-50-01-001-A01
Worksheets
1. GeneralIt is necessary to use these worksheets in relation with chapter 03-50-01.
A. Interim Worksheet:- Fuel Remaining on Board Effect. See FIGURE 09-50-01-991-001-A.- Cargo and Baggage Remaining Effect. See FIGURE 09-50-01-991-002-A.- Total Traffic Load Remaining Effect. See FIGURE 09-50-01-991-003-A.- Ballast Added Effect. See FIGURE 09-50-01-991-004-A.- Waste Water Remaining Effect. See FIGURE 09-50-01-991-005-A.- Non OEW Catering Equipment Added Effect. See FIGURE 09-50-01-991-006-A.- Large Component Movement Effect. See FIGURE 09-50-01-991-007-A.- Potable Water Removed Effect. See FIGURE 09-50-01-991-008-A.- Cockpit and Cabin Crew Removed Effect. See FIGURE 09-50-01-991-009-A.- Catering Equipment Removed Effect. See FIGURE 09-50-01-991-010-A.- Large Component Removed/Missing Effect. See FIGURE 09-50-01-991-011-A.- Hydraulic Fluids Removed Effect. See FIGURE 09-50-01-991-012-A.
B. NRW & Related H & Y Moment Worksheets- NRW & Related H, & Y Moment Worksheet Calculation from OEW. See FIGURE
09-50-01-991-013-A.- NRW & Related H, & Y Moment Worksheet Calculation from DOW. See FIGURE
09-50-01-991-014-A.
09-50-01Page 1
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
LH OUTER TANK
LH INNER TANK
CENTER TANK
CENTER TANK
RH INNER TANK
MOMENTWeight x H−arm
(kgm or lb.in)
WEIGHT(kg or lb)
MOMENTWeight x Y−arm
(kgm or lb.in)
TO TO TO TOSUBTRACT ADD SUBTRACT ADD
TO TOSUBTRACT ADD
TOTAL
RH OUTER TANK
N_AR_095001_1_0010101_01_00
AUXILIARY
Interim WorksheetFuel Remaining on Board EffectFIGURE-09-50-01-991-001-A01
09-50-01Page 2
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TO
WEIGHT(kg or lb)
TO TO TOTO TOADDSUBTRACT SUBTRACT SUBTRACTADD ADD
TOTAL FORWARDCARGO
REMAININGEFFECT
TOTAL AFTCARGO
REMAININGEFFECT
TOTAL BULKCARGO
REMAININGEFFECT
TOTAL
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0020101_01_00
Interim WorksheetCargo and Baggage Remaining Effect
FIGURE-09-50-01-991-002-A01
09-50-01Page 3
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TO
WEIGHT(kg or lb)
TO TO TOTO TOADDSUBTRACT SUBTRACT SUBTRACTADD ADD
TOTAL TRAFFICLOAD
REMAINING
TOTAL
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0030101_01_00
Interim WorksheetTotal Traffic Load Remaining Effect
FIGURE-09-50-01-991-003-A01
09-50-01Page 4
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WEIGHT(kg or lb)
SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD
L/H WINGBALLAST
ADDED EFFECT
R/H WINGBALLAST
ADDED EFFECT
MAIN DECKBALLAST
ADDED EFFECT
FORWARD CARGOBALLAST
ADDED EFFECT
AFT CARGOBALLAST
ADDED EFFECT
BULK CARGOBALLAST
ADDED EFFECT
TOTAL
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0040101_01_00
Interim WorksheetBallast Added Effect
FIGURE-09-50-01-991-004-A01
09-50-01Page 5
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WASTE WATERREMAINING
TO
WEIGHT(kg or lb)
TO TO TOTO TOADDSUBTRACT SUBTRACT SUBTRACTADD ADD
TOTAL
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0050101_01_00
Interim WorksheetWaste Water Remaining EffectFIGURE-09-50-01-991-005-A01
09-50-01Page 6
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WEIGHT(kg or lb)
SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD
NON OEWCATERING
EQUIPMENTEFFECT
TOTAL
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0060101_01_00
Interim WorksheetNon OEW Catering Equipment Added Effect
FIGURE-09-50-01-991-006-A01
09-50-01Page 7
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WEIGHT(kg or lb)
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
TOSUBTRACT
TOADD
NLG RETRACTIONEFFECT
LH MAIN LGRETRACTION
EFFECT
RH MAIN LGRETRACTION
EFFECT
TOTAL
SLATS/FLAPSEXTENSION
EFFECT
N_AR_095001_1_0070101_01_01
TOSUBTRACT
TOADD
TOSUBTRACT
TOADD
Interim WorksheetLarge Component Movement Effect
FIGURE-09-50-01-991-007-A01
09-50-01Page 8
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WEIGHT(kg or lb)
SUBTRACTTO
ADDTO
SUBTRACTTO
ADDTO
SUBTRACTTO
ADDTO
TOTAL
POTABLE WATERREMOVED
EFFECT
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0080101_01_00
Interim WorksheetPotable Water Removed EffectFIGURE-09-50-01-991-008-A01
09-50-01Page 9
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
TO
WEIGHT(kg or lb)
TO TO TOTO TOADD
COCKPIT CREWREMOVED
EFFECT
CABIN CREWREMOVED
EFFECT
SUBTRACT SUBTRACT SUBTRACTADD ADD
TOTAL
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0090101_01_00
Interim WorksheetCockpit and Cabin Crew Removed Effect
FIGURE-09-50-01-991-009-A01
09-50-01Page 10
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
SUBTRACTTO
SUBTRACTTO
SUBTRACTTO
ADDTO
ADDTO
ADDTO
CATERINGEQUIPMENT
TOTAL
WEIGHT(kg or lb)
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0100101_01_00
Interim WorksheetCatering Equipment Removed Effect
FIGURE-09-50-01-991-010-A01
09-50-01Page 11
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
MOMENTWeight x H−arm
(kgm or lb.in)
WEIGHT(kg or lb)
MOMENTWeight x Y−arm
(kgm or lb.in)
SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD
LH WING COMPONENT
REMOVED/MISSING EFFECT
RH WING COMPONENT
REMOVED/MISSING EFFECT
FUSELAGE COMPONENT
REMOVED/MISSING EFFECT
FIN COMPONENT REMOVED/
MISSING EFFECT
THS COMPONENT REMOVED/
MISSING EFFECT
TOTAL
N_AR_095001_1_0110101_01_00
Interim WorksheetLarge Component Removed/Missing Effect
FIGURE-09-50-01-991-011-A01
09-50-01Page 12
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
WEIGHT(kg or lb)
TO TO TO TOSUBTRACT ADD SUBTRACT ADD
TOTAL HYDRAULIC
FLUIDS REMOVEDEFFECT
TOTAL
TO TOSUBTRACT ADD
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
N_AR_095001_1_0120101_01_00
Interim WorksheetHydraulic Fluids Removed EffectFIGURE-09-50-01-991-012-A01
09-50-01Page 13
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
SUBTRACTTO TO
ADD
MOMENTWeight x H−arm
(kgm or lb.in)
WEIGHT(kg or lb)
MOMENTWeight x Y−arm
(kgm or lb.in)
SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD
NON OEW CATERINGEQUIPMENT ADDED
EFFECT
LARGE COMPONENTREMOVED/MISSING
EFFECT
OEW
FUEL REMAINING ONBOARD EFFECT
CARGO AND BAGGAGEREMAINING EFFECT
TOTAL TRAFFIC LOADREMAINING EFFECT
BALLAST ADDED EFFECT
WASTE WATERREMAINING EFFECT
LARGE COMPONENTMOVEMENT EFFECT
POTABLE WATERREMOVED EFFECT
COCKPIT AND CABINCREW REMOVED EFFECT
CATERING EQUIPMENTREMOVED EFFECT
HYDRAULIC FLUIDSREMOVED EFFECT
TOTAL
− − −
===
RESULTS
NRW(kg or lb)
H−arm
(kgm ormoment
Y−arm
(kgm ormoment
lb.in) lb.in)N_AR_095001_1_0130101_01_00
NRW & Related H, & Y Moment WorksheetsNRW & Related H, & Y Moment Worksheet Calculation from OEW
FIGURE-09-50-01-991-013-A01
09-50-01Page 14
Jul 01/09
@A318/A319/A320/A321AIRCRAFT RECOVERY MANUAL
**ON A/C A318-100 A319-100 A320-100 A320-200 A321-100 A321-200
SUBTRACTTO TO
ADD
WEIGHT(kg or lb)
SUBTRACTTO TO
ADD SUBTRACTTO TO
ADD
DOW
= = =
RESULTS
LARGE COMPONENTREMOVED/MISSING
EFFECT
FUEL REMAINING ONBOARD EFFECT
CARGO AND BAGGAGEREMAINING EFFECT
TOTAL TRAFFIC LOADREMAINING EFFECT
BALLAST ADDED EFFECT
WASTE WATERREMAINING EFFECT
LARGE COMPONENTMOVEMENT EFFECT
POTABLE WATERREMOVED EFFECT
COCKPIT AND CABINCREW REMOVED EFFECT
CATERING EQUIPMENTREMOVED EFFECT
HYDRAULIC FLUIDSREMOVED EFFECT
TOTAL
− − −
MOMENTWeight x H−arm
(kgm or lb.in)
MOMENTWeight x Y−arm
(kgm or lb.in)
NRW(kg or lb)
H−arm
(kgm ormoment
Y−arm
(kgm ormoment
lb.in) lb.in)
N_AR_095001_1_0140101_01_00
NRW & Related H, & Y Moment WorksheetsNRW & Related H, & Y Moment Worksheet Calculation from DOW
FIGURE-09-50-01-991-014-A01
09-50-01Page 15
Jul 01/09