Application Notes BPM Series Energy-Saving Power Module Series/40W Power Module
Rev.1.0 Sep, 2014 TAMURA CORPORATION 1 / 17
Rev.1.0
Sep, 2014
Outline
The BPM Energy-Saving Power Module Series is a series of energy-saving switching power modules with built-in
switching transformers, control ICs, control circuits and switching elements (FET).
Attaching the input noise filter, the input rectifier diode and the output smoothing capacitor externally enables the
easy creation of power switching with high-efficiency, low-standby power.
Features
・ Quasi-resonant operations for high efficiency.
・ Operations using both frequency reduction and bursts for generation of low-standby power.
・ Supports worldwide input and PFC output voltages (Vin: DC100V to 420V)
・ Reinforced insulation between Primary and Secondary (AC3000V guaranteed for one minute).
・ Resin filling is available to reduce audible noise.
・ Compliant with all required safety standards for information equipment, AV equipment, industrial equipment, and
home appliance equipment.
・ Various built-in protection functions (overcurrent, overvoltage and overheating protection).
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 2 / 17
① Vin(+)
③ Vin(-)
② Drain
④ Vcc
⑤ VccW
⑥ N.C.
RC(-) ⑧
GND ⑨
GND ⑩
REF ⑦
Vo ⑬
GND ⑪
Vo ⑫
RC(+) ⑭
+DC OUT
-DC OUT
M101
C201
C202
L201C101
C102C103
C104
L101R101
TH101F101
L
N
Vin=85Vac~276Vac
① Vin(+)
③ Vin(-)
② Drain
④ Vcc
⑤ VccW
⑥ N.C.
RC(-) ⑧
GND ⑨
GND ⑩
REF ⑦
Vo ⑬
GND ⑪
Vo ⑫
RC(+) ⑭
+DC OUT
-DC OUT
M101
C201
C202
L201C101
C102C105
C106
L101R101
TH101F101
L
N
Vin=85Vac~276Vac
FG
C203
1. Selecting Externally Connected Equipment
The example of application circuits and parts value which are indicated to this application note aim at assistance
of a design. Therefore, external parts variation or user operating conditions are not fully taken into consideration.
Please take parts variation, operating conditions into consideration when designing.
1.1 Application Circuits
●With FG (Class I Power Supply)
●Without FG (Class II Power Supply)
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 3 / 17
1.2 Parts example
※C102 is calculated based on rated output power equal maximum power.
3.3V **A 5V 8A 12V 3.4A 15 2.7A 24 1.7A
M101 BPM0580SJ BPM1234SJ BPM1527SJ BPM2417SJ
F101 250V 2.0A time lag 250V 2.0A time lag 250V 2.0A time lag 250V 2.0A time lag
TH101 5Ω~10Ω 5Ω~10Ω 5Ω~10Ω 5Ω~10Ω
L101 22mH~47mH/ 1A 22mH~47mH/ 1A 22mH~47mH/ 1A 22mH~47mH/ 1A
L201 2.2uH~10uH / 12A 2.2uH~10uH / 6.8A 2.2uH~10uH / 5.4A 2.2uH~10uH / 3.4A
L202 2.2uH~10uH / 8A 2.2uH~10uH / 3.4A 2.2uH~10uH / 2.7A 2.2uH~10uH / 1.7A
C101 0.1uH~0.22uH / 250V 0.1uH~0.22uH / 250V 0.1uH~0.22uH / 250V 0.1uH~0.22uH / 250V
C102 450V 100uF 450V 100uF 450V 100uF 450V 100uF
C103 100pF~2200pF class Ⅱ 100pF~2200pF class Ⅱ 100pF~2200pF class Ⅱ 100pF~2200pF class Ⅱ
C104 100pF~2200pF class Ⅱ 100pF~2200pF class Ⅱ 100pF~2200pF class Ⅱ 100pF~2200pF class Ⅱ
C105、C106 470pF~2200pF class Ⅰ 470pF~2200pF class Ⅰ 470pF~2200pF class Ⅰ 470pF~2200pF class Ⅰ
C201 10V 2200uF × 4 25V 1500uF × 2 25V 1500uF × 2 35V 680uF
C202 10V 1000uF 25V 820uF 25V 820uF 35V 220uF
C203 1kV 0.022uF 1kV 0.022uF 1kV 0.022uF 1kV 0.022uF
R101 3.3MΩ 500V 3.3MΩ 500V 3.3MΩ 500V 3.3MΩ 500V
PartOutput Specifications
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 4 / 17
1.3 AC input DC output
When using an AC input connector and DC output connector, pay attention to the rated voltage and rated
current of the connector.
Consider the input voltage, withstand voltage and safety standard demanded values and provide a clearance
between AC input connector pins.
1.4 Fuse (F101)
Since a fuse is not built into the module (M101), always install a fuse at the Live side to ensure safety.
Select the fuse by considering the normal current, in-rush current, ambient temperature, and other conditions.
(Discharge the capacitors in the circuit fully and consider the conditions at which the circuit impedance is lowest
when there is a thermistor or other element whose resistance value changes with temperature.)
①Select a rated current of 2 or more times the normal current.
②Consider the rated current rate of change by ambient temperature.(At high temperature: Rated voltage drops)
③Check that the in-rush current and normal current are within the blowout characteristic curve of the fuse.
④Select a fuse so that in-rush current and normal current can take sufficient margin to a fuse permission I2t
curve.
A required margin is subject to the influence by temperature conditions, and the influence of the number of
times of incoming current which occurs in an expected life. We recommend you to ask a fuse maker a proper
margin.
In order to share an input line and an input electrolytic capacitor with another converter, when selecting a fuse
with the high fusing current characteristic, and a high-capacity electrolytic capacitor, there is a case which a
fuse does not blow out at the time of abnormalities.
Please perform a safety check enough in such a case.
1.5 Noise filter (C101,C103,C104,C105,C106,C203,L101)
1.5.1 C101:X capacitor (Across-the-line capacitor)
・ Select the rated voltage matched to the input voltage specifications.
・ Use a safety standard approved product of each country.
1.5.2 C103,C104,C105,C106,C203: Y capacitor (Line bypass capacitor)
・ Use a safety standard approved product of each country.
・ Be careful of the leakage current specified by each safety standard.
・ With a Class II power supply, when connecting directly between the primary and secondary, use a reinforced
insulation product(Y1 class approved).
・ C203 does not require a safety standard approved product, but since the withstand test voltage applied
between the primary and secondary is divided and applied according to the overall capacitance of C105 and
C106 and the capacitance of C203, pay careful attention to the rated voltage.
・
1.5.3 L101:Common mode choke coil
・ Be careful to confirm the rated temperature specified by the wire type and the bobbin insulation used in the
common choke coil
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 5 / 17
1.6 X capacitor discharge resistance (R101)
The voltage immediately before cutoff is charged in the X capacitor even when the input line is in cutoff status.
With a device at which parts of the same voltage as the X capacitor may be touched, a discharge resistor is
necessary according to the capacity of the X capacitor.
Example) IEC60950: When the X capacitor capacitance 0.1µF is exceeded; the time constant shall be 1 or less.
X capacitor capacitance:0.22uF 1≧R101・0.22×10-6
R≦4.5MΩ
In addition, calculate the X capacitor voltage after t seconds from input line cutoff from the following expression
and check that there is no problem.
Vt=Vo(1-e-t/CR) Vt: X capacitor voltage t seconds from input cutoff
Vo: Effective input voltage X√2
C: X capacitor capacitance
R: Discharge resistor value
e: Base of natural logarithm (≒2.71828)
1.7 Rectifying diode(D101)
Always perform full-wave rectification using a bridge diode or general rectifying diodes (use 4 diodes).
When selecting parts, pay attention to the rated voltage, rated current, and temperature rise.
Check that the in-rush current does not exceed the peak surge current and I2t specification of the rectifying
diode.
(Discharge the capacitors in the circuit fully and consider the conditions at which the circuit impedance is lowest
when there is a thermistor or other element whose resistance value changes with temperature.)
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 6 / 17
1.8 Surge current prevention(TH101)
When input power is applied, an in-rush current which charges the input smoothing electrolytic capacitor flows.
An in-rush current that is too large will cause the power supply voltage to become unstable and may affect the
devices which share the power supply. The fuse and rectifying diodes used may also be damaged.
When using a power thermistor to suppress the surge current, select it by paying attention to the following:
①Be sure that the temperature is within the operating temperature range of the thermistor.
②Since the characteristic is such that a rated current drop accompanies a temperature rise, check the highest
temperature of the thermistor and that the load current (power supply input current) is the rated current or
less at the highest temperature.
③With a power thermistor, the relationship between the maximum value of the usable input voltage (rms) and the
capacitance of the input smoothing electrolytic capacitor are set. Check that the relationship between the input
voltage (rms) and input smoothing electrolytic capacitor is not a problem with the thermistor used.
④Since a power thermistor has a large thermal time constant and its resistance value remains low after the input
is tripped, when the input is repeatedly turned on and off, the surge current cannot be controlled. When using
under this condition, check that the effect, etc. on the fuse, bridge diode, and input power supply are no
problem.
The surge current calculation expression is:
As the calculation result is only a reference, conduct a thorough check using actual equipment.
・AC input :
Inrush Current(peak value) : )RR(2)rms(Vin L101TH
I2t : )RR(102C)rms(Vin L101TH2
・DC input
Inrush Current(peak value) : )RR()dc(Vin L101TH
I2t : )RR(2102C)dc(Vin L101TH2
RL:Line impedance (Ω)
RTH101:Thermistor resistance (Ω) at 25℃
C102:electrolytic capacitor(F)
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 7 / 17
① VIN(+)
M101
C102三角波の高周波電流が流れます。配線は太く、短くして下さい。
③ VIN(-)
入力電圧範囲(データシート参照)
入力
電圧
(VDC)
リップル電圧
時間(t)
リップル電圧最小値
入力リップル電圧下限値(データシート参照)
平均電圧
入力電圧範囲240VDC~420VDC
入力
電圧
(VDC)
リップル電圧
時間(t)
リップル電圧最小値
入力リップル電圧下限値215VDC
平均電圧
1.9 Input smoothing electrolytic capacitor(C102)
The input smoothing electrolytic capacitor has a large effect on the characteristics and life of the product.
Select the capacitor by paying attention to the following:
①Install the capacitor very close to the module (M101) and use a wide pattern to connect M101.
②Follow the instructions below to determine the capacitance of the electrolytic capacitors according to the input
voltage to be used.
1) AC 100 V input, worldwide input
Determine the capacitance of the electrolytic capacitors so that the average voltage is equal to or higher than the
lower limit of the input voltage, and so that the minimum ripple voltage is equal to or higher than the lower limit of
the input ripple voltage.
Make sure that the peak voltage of the ripple voltage does not exceed the input voltage range. Take the variation
in capacitance and the capacitance reduction due to aging into consideration when selecting the capacitance.
Datesheet・・・「http://www.tamura-ss.co.jp/electronics/en/powermodule/ 」
2) AC 200 V input
Determine the capacitance of the electrolytic capacitors so that the average voltage is equal to or higher than
240 V, and so that the minimum ripple voltage is equal to or higher than 215 V.
Make sure that the peak voltage of the ripple voltage does not exceed the input voltage range.
Take the variation in capacitance and the capacitance reduction due to aging into consideration when selecting the
capacitance.
A triangle wave high frequency current
flows. Make the wiring wide and short.
Average voltage
Input voltage range
(Refer to the datasheet)
Lower limit of the input ripple voltage
(Refer to the datasheet)
Minimum ripple voltage
Time(t)
Ripple voltage
Inpu
t voltag
e(V
DC)
Time(t)
Inpu
t voltag
e(V
DC)
Minimum ripple voltage
Ripple voltage Average voltage
Input voltage range
240VDC~420VDC
Lower limit of the input ripple voltage
215VDC
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 8 / 17
C102
D101
AC入力
充電電流(低周波)実効値:IL(rms)
放電電流(高周波)実効値:IH(rms)
① VIN(+)
M101
③ VIN(-)
The capacitance of the electrolytic capacitors can be estimated using the formulae below.
The value calculated using the formulae is the minimum required capacitance. Take into consideration variations in the
capacitance of the electrolytic capacitors to be used and reductions in the capacitance due to aging.
As the calculation result is only a reference, conduct a thorough check using actual equipment.
100 V input/WW input ・・・
(reference for the minimum ripple voltage)
And
(reference for the average voltage)
200 V input ・・・
(reference for the minimum ripple voltage)
And
(reference for the average voltage)
Vinmin(rms):Minimum effective input voltage(Vrms)
f:Commercial power frequency(Hz)
Io(max):Maximum output current in use(A)
K:Coefficient (varies depending on model. Refer to the following.)
③Calculate the guaranteed life of the electrolytic capacitor and check that there is no problem.
Since the life calculation expression is different depending on the capacitor manufacturer and type, requesting
life calculation by the manufacturer of the capacitor used is recommended.
Generally, life can be calculated by using the temperature and ripple current of the electrolytic capacitor.
1)Electrolytic capacitor temperature
The temperature at which the temperature on the body of the electrolytic capacitor is maximum is measured
and is made a life calculation parameter.
2) Ripple current
For AC input, a charging current (IL) and discharging current (IH) flow in the input smoothing electrolytic
capacitor. These currents are measured individually and frequency correction is performed on IH and it is
made a life calculation parameter as 120Hz ripple current.
The ripple current (I120) frequency corrected to 120Hz is calculated from the following expression:
2H
2L120 )fc)rms(I()rms(I)rms(I
fc: Frequency correction coefficient (Refer to the electrolytic capacitor catalog.)
Charging current (low frequency)
Effective value: IL (rms)
Discharging current (high frequency)
Effective value: IH (rms)
AC input
・BPM0390SJ : TBD
・BPM0580SJ : 5.88
・BPM1234SJ : 13.3
・BPM1527SJ : 16.7
・BPM2417SJ : 26.7
))75)min(2(5((max)4(min)102 22 rmsVinfIoKC
))100)min(2(1005((max)(min)102 rmsVinfIoKC
))215)min(2(5((max)4(min)102 22 rmsVinfIoKC
))240)min(2(2405((max)(min)102 rmsVinfIoKC
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 9 / 17
入力電流:IDC(rms)
① VIN(+)
M101
C102
③ VIN(-)
DC入力
IDC(rms)
0
IDC(AVE)
放電電流(Idis)
充電電流(Ich)
Vo ⑬
M101
C201三角波の高周波電流が流れます。配線は太く、短くして下さい。
GND ⑨⑩⑪
⑫
For stable DC input, the ripple current by high frequency charging/discharging current is assumed for input
electrolytic capacitor.
The ripple current of an electrolytic capacitor is a triangle wave high frequencycurrent with the input current
(DC current) made the average value. Ripple current is calculated as follows:
22 IchIdisIripple
1.10 Output smoothing electrolytic capacitor(C201)
The output smoothing electrolytic capacitor has a large effect on the characteristics and life of the product.
Select the electrolytic capacitor by paying attention to the following:
①Install the capacitor very close to the module (M101) and use a wide pattern to connect M101.
②Use an electrolytic capacitor with good frequency characteristics and low impedance.
Output ripple and noise and rise time may be affected depending on the ESR and ESL and wiring impedance of
the capacitor.
Input current: IDC (ms)
DC
input
Discharging current (Idis)
Charging current (Ich)
Triangle wave high frequency current flows.
Make the wiring wide and short.
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 10 / 17
0
I0(AVE)
放電電流(Idis)
充電電流(Ich)
③If the capacitance is too large, the overcurrent protection function may operate and the rise may be faulty at
startup. A recommended value is shown in the following table.
Please ask us, when the capacity more than the following table is required.
④Since abnormal oscillation may occur by large phase delay if a capacitor with a very small ESR such as a
tantalum capacitor or multilayer ceramic capacitor is used, use an electrolytic capacitor.
⑤The following rated voltage is recommended:
・BPM0390SJ
・BPM0580SJ
・BPM1234SJ
・BPM1527SJ
・BPM2417SJ
: Rated voltage 10V or more
: Rated voltage 10V or more
: Rated voltage 25V or more
: Rated voltage 25V or more
: Rated voltage 35V or more
⑥Calculate the guaranteed life of the electrolytic capacitor and check that there is no problem.
Since the life calculation expression is different depending on the capacitor manufacturer and type, requesting
life calculation by the manufacturer of the capacitor used is recommended.
Life can be calculated by using the temperature and ripple current of the electrolytic capacitor, the same as the
input smoothing electrolytic capacitor.
1) Electrolytic capacitor temperature
The temperature at which the temperature on the body of the electrolytic capacitor is maximum is measured
and is made a life calculation parameter.
2) Ripple current
A high frequency ripple current by charging/discharging current flows in the input electrolytic capacitor.
The ripple current is calculated by splitting it into the top (charging current) and bottom(discharging current) of
output current (Io).
22 IchIdisIripple
⑦When planning to split the ripple current by using multiple electrolytic capacitors,be sure that ripple current
measurement does not cause an unbalance.
Charging current (Ich)
Discharging current (Idis)
CR mode CC mode
BPM0309SJ TBD TBD
BPM0580SJ TBD TBD
BPM1234SJ TBD TBD
BPM1527SJ TBD TBD
BPM2417SJ TBD TBD
ModelRecommendation capacitance
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 11 / 17
C201-1C201-2
× ○
電流測定されないコンデンサも測定するコンデンサと同じインピーダンスとなるよう
にすると正確な測定ができます。
電流測定用リードなどを測定するコンデンサのみに取り付けると、インピーダンスの
バランスが崩れ正確な測定ができません。
Vo ⑬
M101
GND ⑨⑩⑪
⑫Vo ⑬
M101
GND ⑨⑩⑪
⑫
C201-1 C201-2
Vo ⑬
M101
C201 L201、C202にも高周波電流が流れます。IpでもL201が飽和しないことを確認して下さい。
GND ⑨⑩⑪
⑫
C202
L201Ip
1.11 LCπ type filter(L201,C202)
Output ripple voltage reduction is possible to a certain degree by using a low impedance electrolytic capacitor at
C201. However, the addition of a one-stage LCπ type filter is effective in lowering the output ripple voltage
more.
①Since a ripple current equivalent to C201 may flow depending on the impedance of L201, check the ripple
current,temperature rise, and life of C202 also.
②Triangle wave high frequency current also flows in L201. Check that L201 is not saturated at the peak
current.
In addition, consider the DC resistance of L201 and check that there is no problem with temperature rise.
When current measurement leads, etc. are installed
Only to the capacitor to be measured, the impedance is
unbalanced and accurate measurement is not possible.
When the capacitor whose current is not to be measured
has the same impedance as the capacitor to be measured,
accurate measurement is possible.
High frequency current also flows in L201 and C202.
Check that L201 is not saturated even at Ip.
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 12 / 17
出力
電圧
出力電流
過負荷検出
自動復帰動作低電力領域で間欠動作
2. Protection function
2.1 Overcurrent protection function
An overcurrent protection function is provided as protection when an output short circuit or overload occurs.
The operation mode is automatic reset operation.
・Automatic reset operation
In the output short circuit and overload states, intermittent operation is performed in the low power region.
Operation is automatically reset to normal operation when the short circuit or overload is removed.
2.2 Overvoltage protection function
An overvoltage protection function is provided to prevent damage by impression of an overvoltage onto the load.
The operation mode is latch operation.
When the overvoltage protection circuit operated, it is reset by turning off the input and then turning on the input
again.
Reset time changes with input electrolytic capacity, input voltage, etc.
Avoid impressing a voltage onto the output terminals from the outside by wrap around from overvoltage
operation check and the load side at receiving inspection because it may cause damage.
Overvoltage operation check is a method that checks operation by changing the resistance value of Vref.
For more information, please contact us.
2.3 Overheating protection function
An overheating protection function is provided to prevent damage, smoke generation, etc. if the module
temperature becomes abnormally high for some reason.
The operation mode is latch operation.
When the overheating protection function operated, it is reset by cutting off the input and then turning on the
input again.
Please insure the cause of the over-heat condition is removed prior to resetting the system.
Overload detected
Ou
tpu
t V
olt
age
Automatic reset operation
Intermittent operation in low power region
Output current
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 13 / 17
入力電圧(VDCIN)
出力電圧
90%
起動時間(ts)
① VIN(+)
M101
C102
③ VIN(-)
④ Vcc
C
Vo ⑬
M101
C201
GND ⑨⑩⑪
⑫
C202
L201
① VIN(+)
C102
③ VIN(-)
Vin Vout
3. Startup time adjustment
The startup time at which the output voltage rises to 90% of the specified output voltage after input power is
first applied is set as follows:
The startup time can be adjusted by connecting an external resistor and capacitoras follows:
Connect capacitor C to Vcc (pin 4) and VIN(-) (pin 3) of M101.
Use a capacitor C with a rated voltage of 35V or more.
When using an electrolytic capacitor, check the temperature rise and life.
4. Pattern design precautions
4.1 Main current line
Since the input current, output current, and high frequency current flow in the bold line parts of the connection
diagram (figure below), make the pattern wide and short.
Input voltage (VDCin)
Output voltage
Startup time(ts)
Added capacitor C (µF)
Sta
rtu
p t
ime (
S)
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 14 / 17
5
55
1次
側
2次
側
15
2次部品禁止領域
5
55
1次
側
2次
側
28
1次部品禁止領域
× 悪いパターン例 ○ 良いパターン例
1次
側
2次
側
×
1次
側
2次
側
○
4.2 Input and output capacitors
Install the input smoothing capacitor (C102) and output capacitor (C201) close to M101.
If more than one output capacitor is to be used, all the capacitors must be of the same type and be placed in the
same location so that they are not affected by circuit patterns.
When there is a PFC output capacitor and a separate inverter smoothing capacitor, these capacitors can be
shared. However, when the distance is long, the input smoothing capacitor only for M101 must be installed near
M101. In addition, when the pattern from the output terminals and load of M101 is narrow and long, make the
pattern wide thick and short because it had an effect on output accuracy.
4.3 Pattern prohibited area
When a double sided circuit board is used, do not provide a pattern directly below M101 of the parts side of the
circuit board. If there is a pattern directly below M101 of the parts side, the insulation distance between the
primary and secondary sides will not meet the specified value and safety cannot be ensured.
The installation prohibited area of primary parts and secondary parts is shown in the figure below.
Do not install parts inside the dotted lines.
Example of a bad pattern
Example of a good pattern
Pri
ma
ry s
ide
Seco
nd
ary
sid
e
Pri
ma
ry s
ide
Seco
nd
ary
sid
e
Pri
ma
ry s
ide
Seco
nd
ary
sid
e
P
rim
ary
sid
e
S
eco
nd
ary
sid
e
Secondary parts prohibited area
Primary parts prohibited area
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 15 / 17
・Parts side view
・Numbers with a circle are pin numbers
To provide strength against vibration
and dropping, provide lands at all pins and solder.
Unit : mm
× 悪い配置例 ○ 良い配置例
電解コンデンサ 電解コンデンサ
ノイズフィルターとモジュールの間にブリッジダイオードと電解コンデンサを配置することを推奨します。
Xコ
ンチョーク
Xコン
ブリッジダイオード チョー
ク
ブリ
ッシ
゙ダイ
オート
゙
モジュール
モジュール
5. Noise filter layout precautions
When a noise filter (X capacitor, choke) is located near the module, the original noise reduction effect may not
be produced and noise reduction may become difficult.
Make the distance between noise filter and module long.
6. Recommended hole diameter, land, and pin pitch
7. Recommended soldering conditions (lead-free solder)
①Flow soldering: 255±3 ℃ 5 seconds or less preheat end 110℃±10℃
②Soldering iron: 350℃(MAX) 4 seconds or less
Installing a bridge diode and electrolytic capacitor
between noise filter and module is recommended.
Example of good layout Example of bad layout
Module
Module
Bridge diode
X capacitor
Choke
Electrolytic capacitor Electrolytic
capacitor
Bridge d
iode
X c
apac
itor
Cho
ke
Hole dia.φ1.4±0.1
Land dia.φ3.0
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 16 / 17
0 20 40 60 80-20 -10 10 30 50 70
20
40
60
80
100
0
周囲温度(℃)
負荷
率(%
)
発熱部品
モジュール
周囲温度測定箇所
発熱部品
周囲温度測定箇所
モジュール
周囲温度測定箇所
20mm
20m
mモジュール
周囲温度測定箇所
モジュール
モジュールの中心の延長線
8. Output derating
When the ambient temperature exceeds +50℃, reduce the output power in accordance with the output derating
chart below.
When the ambient temperature is affected by the heat generated by surrounding components, then the ambient
temperature measurement point must be made in proximity to the heat generating components as shown below
When there are no heat generating parts nearby, make the temperature 20mm from the module and 20mm above
the circuit board the ambient temperature.
Ambient temperature measurement point when there are heat generating parts nearby
Ambient temperature measurement point when there is no effect of heating generating part
Loa
d f
act
or
(%)
Ambient temperature (°C)
Ambient temperature
measurement point
Ambient temperature
measurement point
Module
Module
Ambient temperature
measurement point
Ambient temperature
measurement point
Module
Module
Heat
generating
parts
Heat
generating
parts
Extended line of center
of module
BPM Series Application Notes
Rev.1.0 Sep, 2014 TAMURA CORPORATION 17 / 17
User Precautions
●The content of this manual is subject to change without prior notice for the purpose of improvements, etc.
Ensure that you are in possession of the most up-to-date information when using this product.
●The operation examples and circuit examples shown in this manual are for reference purposes only, and Tamura
Corporation disclaims all responsibility for any violations of industrial property rights, intellectual property rights
and any other rights owned by Tamura Corporation or third parties that these may entail.
●The circuit examples and part constants listed in these specifications are provided as reference for the
verification of characteristics. The user is to perform design, verification, and judgment under his or her own
responsibility, taking into account the various conditions.
●Tamura Corporation constantly strives to improve quality and reliability, but functional failures and failures are
bound to occur with some probability in power products. To ensure that failures do not cause accidents
resulting in injury or death, fire accidents, social damage, and so on, users are to thoroughly verify the safety
of their designs in devices and/or systems.
●This product is intended for use in consumer electronics (electric home appliances, business equipment,
information equipment, communication terminal equipment, measuring devices, and so on.) If considering use of
this product in equipment or devices that require high reliability (medical devices, transportation equipment,
traffic signal control equipment, fire and crime prevention equipment, aeronautics and space devices, nuclear
power control, fuel control, in-vehicle equipment, safety devices, and so on), please consult a Tamura sales
representative in advance. Do not use this product for such applications without written permission from
Tamura Corporation.
●This product is intended for use in environments where consumer electronics are commonly used.
It is not designed for use in special environments such as listed below, and if such use is considered, the
user is to perform thorough safety and reliability checks under his/her responsibility.
- Use in liquids such as water, oil, chemical solutions, or organic solvents, and use in locations where the product
will be exposed to such liquids
- Use that involves exposure to direct sunlight, outdoor exposure, or dusty conditions
- Use in locations where corrosive gases such as salt air, C12, H2S, NH3, SO2, or NO2, are present
- Use in environments with strong static electricity or electromagnetic radiation
- Use that involves placing inflammable material next to the product
- Use of this product either sealed with a resin filling or coated with resin
- Use of water or a water soluble detergent for flux cleaning
- Use in locations where condensation is liable to occur
●This product is not designed to resist radiation.
●This product is not designed to be connected in series or parallel.
Do no operate this product in a series, parallel, or N+1 redundant configuration.
●The content of this manual may not be transferred or copied without prior written permission.
Top Related