www.asconumatics.euX021-27-26
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
Accessory Description Order Code
2005 Regulator repair kit
0.2 to 2 bar 214-221
0.3 to 4 bar 214-222
0.7 to 9 bar 214-223
2012 Regulator repair kit
0.2 to 2 bar 239-1909
0.3 to 4 bar 239-1910
0.7 to 9 bar 239-1911
2035 Regulator repair kit
0.2 to 2 bar 239-2220
0.3 to 4 bar 239-2221
0.7 to 9 bar 239-2222
20052012
Elbow kit 239-1217
Retaining clip 131-236
2005 Extension kit 239-1790
200520122035
Gauge to max. 11 bar 214-215
Gauge to max. 4 bar 214-220
200520122035
Adapter, port G1/8 239-2048
Retaining clip 131-236
Accessories • Sandwich Pressure Regulators
2005 / 2012 / 2035 Series
Spare Parts • Sandwich Components
Sandwich speed controls for valves and regulators are equipped with an integral plug-in system. Sandwich speed con-trols provide a variable restriction in ports 3 and 5 in order to control the cylinders’ extend and retract speed. To facilitate easy adjustment both screws are on the same side of the speed control.
Note: Sandwich speed controls can only be used with single sandwich pressure regulators.
Single Solenoid PilotActuated, 5-port., 2-pos. Valve
Single SandwichPressure Regulator
Sandwich Speed ControlPlug-in System
Stud Manifold Block
Sandwich Speed Control
Accessory Description Order code
Sandwich speed control
2005 239-15972005
ISO15407-2 245-122
2012 239-12602012
ISO15407-2 239-2521
2035 239-2223
Shut-off sandwich plate
- Only apply with internal pilot air.- Regulator and sandwich speed control must be
mounted in the lowest position.- If used with regulator, only use with ES or ED
regulator.- Regulated pressure > 1.8 bar.
2005 239-1596
2012 239-1585
Sandwich pressure block
- Used to supply a separate pressure to a single valve station without needing blocking disks.
XE32145X
1
X 5 4 1 2 3 XE
2005 239-21882005
ISO15407-2 245-164
2012 239-14362012
ISO15407-2 245-141
2035 239-2228
Sandwich exhaust block
- Used to isolate the exhaust of a single valve station from the manifold.
- Allows faster exhaust response by re-routing.- Exhaust externally to the manifold.
32145X
5 3
XE32145X
XE2005 239-21892005
ISO15407-2 245-163
2012 239-15562012
ISO15407-2 245-140
2035 239-2230
2005 / 2012 / 2035 Series
www.asconumatics.eu X021-27-27
0049
6GB
-201
1/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
Assembly/disassembly of bar:- 2005: 2 mm external hex key- 2012 & 2035: 2.5 mm external hex key2005 - 2012 2035
Accessory Description Order Code
Blank station plate(screw, blank station plate, O-ring, gasket)
2005 239-1712
2005ISO 15407-2 245-123
2012 239-1990
2012ISO 15407-2 239-2497
2035 239-2218
Blocking disks
for port 1 20052012
124-341for port 3/5 239-907
for port 1, 3/5 2035 239-2219
Cover for end plate
screw 2005 127-368cover 105-436screw 2012 127-368cover 105-400screw 2035 127-396cover 105-456
Cover for end plate with muffler
screw 2005 127-368105-435cover
2012127-368screw
right end cover 005-193left end cover 005-194
2035 127-396screwcover 105-457
Gasket for end plate cover
2005 113-5742012 113-5362035 113-621
Muffler for end plate cover
2005 125-1012
2012 125-851
2035 125-1098
Plug for conversion of pilot supply20052012 213-497
2035 213-590
DIN rail mounting 20052012 239-980
2005 / 2012 / 2035 SeriesSpare Parts
Accessory Description Order Code
Interchangeable cartridge fittings
Push-in fitting for ports 1, 3, 5 (10 mm)
2005
134-509Push-in fitting for ports X, XE (6 mm) 134-499Push-in fitting for ports 2, 4 (6 mm) 134-534Push-in fitting for ports 2, 4 (8 mm) 134-501Blocking plug for ports 1, 3, 5 239-1190Blocking plug for ports X, XE 239-1086Blocking plug for ports 2, 4 239-1085Push-in fitting for ports 1, 2, 4 (8 mm)
2012
134-507
Push-in fitting for ports 1, 2, 4 (10 mm) 134-509
Push-in fitting for ports X, XE (4 mm) 134-498
Push-in fitting for ports X, XE (6 mm) 134-499
Push-in fitting for ports 3, 5 (12 mm) 134-511
Push-in fitting for ports 3, 5 (14 mm) 134-513
Blocking plug for ports 1, 2, 4 239-1190
Blocking plug for ports X, XE 239-1086
Blocking plug for ports 3, 5 239-1191
www.asconumatics.euX021-27-28
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
End plate kit, supply ports on both sides, with thread
End plate kit, supply ports on both sides, with push-in fittings
End plate kits Order Code Weight Port 1 3/5 X/XE 1 3/5 X/XE approx. [kg] Size G 3/8 G 3/8 G 1/8 10 mm 10 mm 6 mm Without muffler, standard mount 0.880 239-1646 239-1654Without muffler, for DIN rail mounting 0.822 239-1645 239-1653With muffler, standard mount 0.805 239-1644 239-1652
With muffler, for DIN rail mounting 0.815 239-1643 239-1651On request: with NPTF thread
2005 Series
End plate kit, supply ports on both sides, with thread
End plate kit, supply ports on both sides, with push-in fittings
End plate kits Order Codewith supply ports Port Weight 1-3/5-X/XE 1-3/5-X/XE Weight 1-3/5-X/XE Weight 1-3/5-X/XEon both ends Size approx.
[kg]ISO228/1-G
3/8-1/2-1/8NPTF
3/8-1/2-1/8approx.
[kg]PUSH-IN8-12-6 mm
approx. [kg]
PUSH-IN10-14-6 mm
Without muffler standard mount 1.215 239-1240 239-1236 1.335 239-1255 1.300 239-1256
Without muffler for DIN rail mounting 1.235 239-1239 239-1235 1.355 239-1253 1.320 239-1254
With muffler, standard mount 1.150 239-1238 239-1234 1.200 239-1251 1.205 239-1252
With muffler, for DIN rail mount 1.170 239-1237 239-1233 1.220 239-1249 1.225 239-1250
2012 Series
Spare Parts • End Plate Kits
2005 / 2012 / 2035 Series
www.asconumatics.eu X021-27-29
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
End plate kit
End plate kits Order Code Weight Port 1 3/5 X/XE approx. [kg] Size 1/2 1/2 1/8End plates with muffler 2.050 239-2207End plates without muffler 2.050 239-2208LH ports with muffler, RH mounting cover with pilot exhaust 2.050 239-2215LH ports without muffler, RH mounting cover with pilot exhaust 2.050 239-2216On request: with NPTF thread
2035 Series
Spare Parts • End Plate Kits
2005 / 2012 / 2035 Series
2012 Series
www.asconumatics.euX021-27-30
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
End plate kit, supply ports on left side, with thread
End plate kit, supply ports on left side, with push-in fittings
End plate kits Order CodePort Weight 1-3/5-X/XE 1-3/5-X/XE Weight 1-3/5-X/XE Weight 1-3/5-X/XESize approx.
[kg]ISO228/1-G
3/8-1/2-1/8NPTF
3/8-1/2-1/8approx.
[kg]PUSH-IN8-12-6 mm
approx. [kg]
PUSH-IN10-14-6 mm
LH ports without muffler 0.850 239-1692 239-1688 0.915 239-1707 0.900 239-1707
LH ports w/o muffler, with DIN rail 0.870 239-1691 239-1687 0.935 239-1705 0.920 239-1706
LH ports with muffler, w/o DIN rail 0.820 239-1690 239-1686 0.850 239-1703 0.850 239-1704
LH ports with muffler, with DIN rail 0.890 239-1689 239-1685 0.870 239-1701 0.870 239-1702
Spare Parts • End Plate Kits ISO 15407-2
2012 ISO 15407-2 26mm Series
2005 ISO 15407-2 18mm SeriesEnd plate kit, supply ports on both sides, with thread
End plate kit, supply ports on both sides, with push-in fittings
2005 / 2012 / 2035 Series
www.asconumatics.eu X021-27-31
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
End plate kits 18 mm Order CodePort Weight 1-3/5-X/XE 1-3/5-X/XE 1-3/5-X/XESize approx.
[kg]NPTF
3/8-3/8-1/8ISO228/1-G
3/8-3/8-1/8PUSH-IN
10-10-6 mm
w/o muffler, w/o DIN rail 0.88 242-124 242-128 242-136
w/o muffler, w/ DIN rail 0.82 242-123 242-127 242-135
w/ muffler, w/o DIN rail 0.80 242-122 242-126 242-134
w/ muffler, w/ DIN rail 0.82 242-121 242-125 242-133
End plate kits 26 mm Order CodePort Weight 1-3/5-X/XE 1-3/5-X/XE Weight 1-3/5-X/XE 1-3/5-X/XESize approx.
[kg]NPTF
3/8-1/2-1/8ISO228/1-G
3/8-1/2-1/8approx.
[kg]PUSH-IN8-12-6 mm
PUSH-IN10-14-6 mm
w/o muffler, w/o DIN rail 1,22 239-2398 239-2402 1,33 239-2417 239-2418
w/o muffler, w/ DIN rail 1,24 239-2397 239-2401 1,35 239-2415 239-2416
w/ muffler, w/o DIN rail 1,15 239-2396 239-2400 1,20 239-2413 239-2414
w/ muffler, w/ DIN rail 1,17 239-2395 239-2399 1,22 239-2411 239-2412
End plate kits 26 mm Order CodePort Weight 1-3/5-X/XE 1-3/5-X/XE Weight 1-3/5-X/XE 1-3/5-X/XESize approx.
[kg]NPTF
3/8-1/2-1/8ISO228/1-G
3/8-1/2-1/8approx.
[kg]PUSH-IN8-12-6 mm
PUSH-IN10-14-6 mm
LH ports only Kit w/o muffler, w/o DIN rail 0,85 239-2422 239-2426 0,91 239-2446 239-2445
LH ports only Kit w/o muffler, w/ DIN rail 0,87 239-2421 239-2425 0,93 239-2443 239-2444
LH ports only Kit w/ muffler, w/o DIN rail 0,82 239-2420 239-2424 0,85 239-2437 239-2442
LH ports only Kit w/ muffler, w/ DIN rail 0,89 239-2419 239-2423 0,87 239-2435 239-2436
End plate kit, supply ports on one side, with thread
End plate kit, supply ports on one side, with push-in fittings
End plate kit, supply ports on both sides, with thread
End plate kit, supply ports on both sides, with push-in fittings
05 1 BB 4 00 M 0 000 61Valve Model Number
Port Size of Base 2005 2012 2035
1 = Valve w/o manifold X2 = Valve w/o manifold X3 = Valve w/o manifold X
ActuatorBA = Single actuated and spring return
flush non-locking manual overrideBB = Double actuated, flush non-locking manual overrideBN = ISO 15407-2: Single actuated and differential return,
flush non-locking manual override
Mounting00 = Valve unit only
Voltage20 = 24 / 50-60 Hz30 = 120 / 50-60 Hz60 = 12 VDC61 = 24 VDC
Port Type of Bases0 = Without base
Wiring OptionsK = Plug-in, AC with LEDM = Plug-in, DC with LED
Spare Parts • Valves
Function 2005 2012 20354 = 5-port., 2-pos. valve X X X5 = 5-port., 3-pos. valve, open center, dual
pressure X X X
6 = 5-port., 3-pos. valve, closed center X X X7 = 5-port., 3-pos. valve,
1 connected with 2 & 4, 3 & 5 blocked X X
D = Dual 3-port., 2-pos. valve “14” NC, “12” NC X XE = Dual 3-port., 2-pos. valve “14” NC, “12” NC,
vacuum service X
Ribbon cable option must be used for manifold
assemblies that exceed 16 solenoids. (7th and 8th digit of valve order code) (please refer to explanations on page X021-27-34)
Options
000 = Without option
11B = Locking override
11M = Without manual override
14X = External pilot supply (only for series 2012 with base options 3A + 3C)
56Y = 12 mm Electrical connector (in conduit port of 2012 series base mounting only)
Further options on request
Symbols
BB6*
BB7*
BB5*
BB4
BA4
BBE*
BBD*
BN4*
I5/I6...05/12/35...
R5/R6...
I5/I6...05/12/35...
I5/I6...05/12/35...
R5/R6...05/12/35...
I5/I6...05/12/35...
R5/R6...05/12/35...
R5/R6...05/12/35...
5-port., 3-pos. valve, open center, dual pressure
5-ported, 2-pos. valve,detented
5-ported, 2-pos. valve,spring return
5-ported, monostable,differential return
5-port., 3-pos. valve, closed center
5-port., 3-pos. valve, 1 connected with 2 & 4, 3 & 5 blocked
Dual 3-port., 2-pos. valvevacuum service“14” NC, “12” NC
Dual 3-port., 2-pos. valve“14” NC, “12” NC
14
1224
5 31
1224
5 31
14
1224
5 31
14
1224
5 31
14
1224
5 31
1424
31
514 12
24
31
514 12
1214 24
5 31
www.asconumatics.euX021-27-32
0049
6GB
-201
3/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
Series05 = 2005 Series12 = 2012 Series35 = 2035 SeriesI5* = 2005 Series ISO 15407-2 18mmI6* = 2012 Series ISO 15407-2 26mmR5*(1)= 2005 Series ISO 15407-2 18mmR6*(1)= 2012 Series ISO 15407-2 26mm
*see the symbols table bellow to verify compatibility with spool valves functions
(1) rubber packed spool
05 1 ES 1 00 J 0 000 00
Spare Parts • Sandwich Pressure RegulatorsSandwich Pressure Regulator Model Number
Pressure Range1 = 0.7 to 9 bar3 = 0.2 to 2 bar4 = 0.5 to 4 bar
Options000 = Standard12H = Without gauge16N = Jumper on 14 end 16P = Jumper on 12 end
16W = Top facing gauge* (2005 series)
61Y = Extended gauge* (2005 series)63D = 16W + 61Y* (2005 series)* see note belowFurther options on request
Wiring OptionJ = Plug-in receptacle
Mounting 2005 2012-3500 = Regulator unit only X X
Port Type of BasesO = Without base
Port Size of Base 2005 2012 2035
1 = Valve w/o manifold X
2 = Valve w/o manifold X
3 = Valve w/o manifold X
Regulator TypeES = Single pressure to port 1ED = Dual pressure to ports 3 and 5
EC = Dual pressure with non-relieving checks (2012 and 2035 series)
EQ = Dual pressure with relieving checks (2012 and 2035 series)
EE = Dual pressure to ports 4 and 2ET = Two-pressure selector
Ribbon cable option must be used for manifold assemblies that exceed 16 solenoids.
(7th and 8th digit of valve order code) (please refer to explanations on page X021-27-34)
Note (2005 series):Regulator gauges must be offset on alternating sta-tions to prevent interference (see photo)• Odd numbered stations will use either standard (no
option) or top facing (“16W” option) gauges.• Even numbered stations will use either extended
standard (“61Y” option) or extended top facing (“63D” option) gauges.
Series05 = 2005 Series12 = 2012 Series35 = 2035 SeriesI5 = 2005 Series ISO 15407-2 18mmI6 = 2012 Series ISO 15407-2 26mm
Symbols
14
122
4
14513
12
24
14513
12
1412
14513
12
24
Single pressure from a single supply
Dual pressure from a single supply
Non-relieving: taps downstream pressure if
upstream is exhausted
14513
12
24
145
5
4 2
31
13
12
24
14513
12
1412
122
4
14
Relieving:exhausts pressure in cylinder
if upstream pressure is exhausted
External outlet regulator used with jumper plate for single or
dual pressure
Two-pressure selector used for multi-pressure applications
ES ED EC(2012-2035)
ETEEEQ(2012-2035)
www.asconumatics.eu X021-27-33
0049
6GB
-200
9/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
Spare Parts • Manifold Assembly Kits “Z-Boards”™“Z-Boards”™ 2005 Series includes 4 different “Z-Boards”™ for driving up to 32 solenoids of single and double solenoid actuated valves.Ribbon cable feature must be used for manifold assemblies that exceed 16 solenoids.In order to allow the full capacity of 32 solenoids, the assembly must be configured so that an even number of solenoids is utilised prior to the station using the ribbon cable feature.
Note: The 16th and 17th solenoid cannot be on the same valve.(See valve model number selection for 7th and 8th digit for valve with 17th solenoid).
Manifold Assemblies
Manifold assemblies Order Code*with bottom ports Weight Side portsin G 1/4 or NPTF approx. [kg] G 1/4 NPTF 1/4 G 3/8 NPTF 3/8 8 mm push-in 10 mm push-inWith single “Z-Board”™ 0.290 206-1256 206-1272 206-1255 206-1271 206-1257 206-1258
With double “Z-Board”™ 0.290 206-1264 206-1280 206-1263 206-1279 206-1265 206-1266With single “Z-Board”™ and ribbon cable 0.312 206-1260 206-1276 206-1259 206-1275 206-1261 206-1262With double “Z-Board”™ and ribbon cable 0.310 206-1268 206-1284 206-1267 206-1283 206-1269 206-1270* Manifold assemblies with adapter to ISO 15407-2, see following page.
Manifold assemblies Weight Order Code* with bottom ports Side portsin G 1/8“ or 1/4“ approx. [kg] G 1/8 NPTF 1/8 6 mm push-in 8 mm push-in With single “Z-Board”™ 0.255 206-1371 206-1373 206-1387 206-1363** With double “Z-Board”™ 0.253 206-1372 206-1374 206-1388 206-1364**With single “Z-Board”™ and ribbon cable 0.275 206-1375 206-1377 206-1389 206-1379**With double “Z-Board”™ and ribbon cable 0.273 206-1376 206-1378 206-1390 206-1380*** Manifold assemblies with adapter to ISO 15407-2, see following page.** Bottom ports G 1/4“
Manifold assemblieswith side ports with bottom ports
BOrder Code G 1/2“ G 3/8“
Order CodeNPTF 1/2“NPTF 3/8“
Order CodeG 3/8“G 3/8“
Order CodeNPTF 3/8“NPTF 3/8“
Weightapprox.
[kg]
With single “Z-Board”™ 206-1610 206-1608 206-1611 206-1609 0.640
With double “Z-Board”™ 206-1614 206-1612 206-1615 206-1613 0.645
With single “Z-Board”™ and ribbon cable 206-1622 206-1620 206-1623 206-1621 0.690
With double “Z-Board”™ and ribbon cable 206-1618 206-1616 206-1619 206-1617 0.695
2005 Series
2005 / 2012 / 2035 Series
2012 Series
2035 Series
www.asconumatics.euX021-27-34
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
2005 / 2012 / 2035 Series
www.asconumatics.eu X021-27-35
Manifold Assembly Kits to ISO 15407-2
Spare Parts • Manifold Assembly Kits to ISO 15407-2
Manifold Assembly Kits - Size 18 mm ISO 15407-2Side ports 1/8 NPTF G 1/8 1/4 Push-in 6mm Push-in 5/16 (8mm) Push-in
Bottom ports 1/8 NPTF G 1/8 1/4 NPTF G 1/8 G 1/8
Single “Z-Board”™ 206-1719 206-1717 206-1723 206-1725 206-1721
Double “Z-Board”™ 206-1720 206-1718 206-1724 206-1726 206-1722Single “Z-Board”™ w/ ribbon cable 206-1729 206-1727 206-1733 206-1735 206-1731Double “Z-Board”™ w/ ribbon cable 206-1730 206-1728 206-1734 206-1736 206-1732Passive 206-1738 206-1737 206-1740 206-1741 206-1739
Manifold Assembly Kits - Size 26 mm ISO 15407-2Side ports 1/4 NPTF 3/8 NPTF G 1/4 G 3/8 1/4 Push-in
Bottom ports 1/4 NPTF 1/4 NPTF G 1/4 G 1/4 1/4 NPTF
Single “Z-Board”™ 206-1665 206-1668 206-1669 206-1672 206-1679
Double “Z-Board”™ 206-1666 206-1667 206-1670 206-1671 206-1680Single “Z-Board”™ w/ ribbon cable 206-1687 206-1681 206-1683 206-1686 206-1695Double “Z-Board”™ w/ ribbon cable 206-1688 206-1682 206-1684 206-1685 206-1696Passive 206-1700 206-1699 206-1698 206-1697 206-1704
Manifold Assembly Kits - Size 26 mm ISO 15407-2Side ports 3/8 Push-in 8 mm Push-in 10 mm Push-in
Bottom ports 1/4 NPTF G 1/4 G 1/4
Single “Z-Board”™ 206-1677 206-1673 206-1675
Double “Z-Board”™ 206-1678 206-1674 206-1676 Single “Z-Board”™ w/ ribbon cable 206-1693 206-1689 206-1691 Double “Z-Board”™ w/ ribbon cable 206-1694 206-1690 206-1692 Passive 206-1703 206-1701 206-1702
7
6
8
2
1
2
54
3
Ribbon cable for Valve Station with 17th Solenoid
Description Order Code
2005 239-1840Ribbon cable 2012 239-1336 2035 239-2226
0049
6GB
-201
3/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
2005 / 2012 / 2035 Series
www.asconumatics.euX021-27-36
Spare Parts • Mid-Station Supply & Exhaust Block
Mid-Station Supply & Exhaust Block
Description Weight Order approx. [kg] Mid-station supply & exhaust block with threaded side ports in G 1/8* 0.205 239-1789 Mid-station supply & exhaust block with side push-in fittings 0.240 239-1788* On request: Threaded ports in NPTF 1/8
• Add additional supply and exhaust capacity to large manifold assemblies• Add different pressure to manifold section with use of blocking disks• Same size as standard manifold block with blank station plate
Description Weight Order approx. [kg] CodeMid-station supply & exhaust block with threaded side ports in G 3/8 0.290 239-1331
Mid-station supply & exhaust block with threaded side ports in NPTF 3/8 0.290 239-1330Mid-station supply & exhaust block with side push-in fittings 10 mm 239-1333
Description Weight Order approx. [kg] CodeMid-station supply & exhaust block 0.770 239-2225On request: Threaded ports in NPTF
2005 Series
2012 Series
2035 Series
Manifold Assemblies with Aux. 24 VDC Power Connection
2005 Series Description Weight Order approx. [kg] CodeManifold assembly with single “Z-Board”™, side ports with 8 mm push-in fittings 0.255 206-1430Manifold assembly with double “Z-Board”™, side ports with 8 mm push-in fittings 0.255 206-1462
2012 Series Description Weight Order approx. [kg] CodeManifold assembly with single “Z-Board”™, side ports with 10 mm push-in fittings 0.290 206-1428Manifold assembly with double “Z-Board”™, side ports with 10 mm push-in fittings 0.290 206-1429
0049
6GB
-200
8/R
02²
Ava
ilabi
lity,
des
ign
and
spec
ifica
tions
are
sub
ject
to c
hang
e w
ithou
t not
ice.
All
right
s re
serv
ed.
2005 Series
2012 Series
2035 Series
Plug for conversion of pilot supply20052012 213-497
2035 213-590
2005 / 2012 / 2035 Series
Spare Parts • Conversion of Pilot Air Supply
www.asconumatics.eu X021-27-37
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
Conversion of Pilot Air Supply
Manifolds can easily be converted from internal to external pilot supply.
When converting from internal to external pilot supply, please ensure that the manifold is not pressurised, as pressure is applied to the end plate covers.
For external pilot supply plug here.
Left end plate only!
For internal pilot supply plug here.
Left end plate only!
For external pilot supplyplug here.
For internal pilot supplyplug here.
In both end plates!
For internal pilot supply plug here.
In both end plates!
For internal pilot supplyplug here.
Left end plate only!
For external pilot supplyplug here.Left end plate only!
C A
B
-
Spare Parts • Adaptor Plate Kits
2012 Series
Adaptor Plate Kits
Description A B C Weight Order approx. [kg] CodeTransition plate for 2012 left of 2005 133.0 56.0 26.0 0.400 239-1965Transition plate for 2012 ISO 15407-2 26mm left of 2005 ISO 10407-2 18mm 133.0 56.0 26.0 0.400 245-156Transition plate for 2012 ISO 15407-2 26mm left of ISO 5599/2 size 2 195.0 65.0 24.8 0.400 245-187C
Dimensions [mm]
The kit includes the adapter plate, transfer board, gasket, screws and studs. Individual end plates for the 2005 and 2012 are not incuded. This adaptor allows the transition from the 2012 to the 2005 series.
EXAMPLE ORDERS: Adapter plate kit: AKJGBEB003LMUFValves: 122BB4Z2ML00061 122BA4Z1ML00061 053BA4Z1ML00061 053BA4Z1ML00061and mounting: ASSEMBLED
Transition Plate Kit only
Adaptor Plate Kit with Standard End Plates(“STD“ Option)Description Order Code2005 with 3/8 G-tap to 2012 with 3/8 and 1/2 G-tap
239-2068
2005 with 10 mm push-in to 2012 with 10 and 14 mm push-in
239-2076
Adaptor Plate Kit with Standard End Plates and Muffler(“MUF“ Option)Description Order Code2005 with 3/8 G-tap to 2012 with 3/8 and 1/2 G-tap
239-2069
2005 with 10 mm push-in to 2012 with 10 and 14 mm push-in
239-2077
Adaptor Plate Kit with Standard End Plates and DIN rail mount(“DRM“ Option)Description Order Code2005 with 3/8 G-tap to 2012 with 3/8 and 1/2 G-tap
239-2070
2005 with 10 mm push-in to 2012 with 10 and 14 mm push-in
239-2078
Adaptor Plate Kit with Standard End Plates, muffler and DIN rail mount (“DWM“ Option)Description Order Code2005 with 3/8 G-tap to 2012 with 3/8 and 1/2 G-tap
239-2071
2005 with 10 mm push-in to 2012 with 10 and 14 mm push-in
239-2079
www.asconumatics.euX021-27-38
0049
6GB
-200
9/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
A
Spare Parts • Transition Plate Kits
Transition Plate Kits
Adapter plate kit
The kit includes the adapter plate, transfer board, gasket, screws and studs. Individual end plates for the 2005 and 2012 are not incuded. This adaptor allows the transition from the 2035 to the 2012 series.
EXAMPLE ORDERS* : Adapter plate kit: AKJBBGB00XGMUF Valves: 354BA4Z1MG00061 354BB4Z2MG00061 122BA4Z1MG00061 122BB4Z2MG00061and mounting: ASSEMBLED
*2012 Series = G
Adapter Plate Kit with Standard End Plates(“STD“ Option)Description Order Code2035 with 1/2 G-tap to 2012 with 3/8 and 1/2 G-tap
239-2280
2035 with 1/2 NPTF-tap to2012 with 3/8 and 1/2 NPTF-tap
239-2279
Adapter Plate Kit with Standard End Plates and Muffler (“MUF“ Option)Description Order Code2035 with 1/2 G-tap to 2012 with 3/8 and 1/2 G-tap
239-2282
2035 with 1/2 NPTF-tap to2012 with 3/8 and 1/2 NPTF-tap
239-2281
Description A Order CodeTransition plate for 2035 left of 2012 30.0 239-2278
Dimensions [mm]
Transition Plate Kit only
2035 Series
www.asconumatics.eu X021-27-39
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
F
G HE
D
B CA
G
H JFE
D
AB C
www.asconumatics.euX021-27-40
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
End Plate with 25 Pin SUB-D Connector (“J”)
G2-2 Electronics • Spare Parts • End Plate with Sub-D Connector
Pin 25Earth ground
Pins 23-24COMMON
Pins 1-22 Drive of coils
25 PIN SUB-D CONNECTOR
Pins 1-22OUTPUTS
Pins 23-24COMMON
Pin 25Earth ground239-...
Clearance holefor M6 screw
Dimensions [mm]Description A B C D E F G H J Weight
approx. [kg]OrderCode
End plate, 25 pin standard mount 36.8 7.4 10.7 75.8 58.9 6.4 61.0 62.7 — 0.200 239-1174
End Plate with 37 Pin SUB-D Connector (“M“)
Dimensions [mm]Description A B C D E F G H J Weight
approx. [kg]OrderCode
End plate, 37 pin standard mount 36.8 7.4 10.7 75.8 51.8 58.9 6.4 61.0 62.7 0.200 239-1180
Pin 37Earth ground
Pins 35-36COMMON
Pins 1-32Drive of coils
Clearance holefor M6 screw
37 PIN SUB-D CONNECTOR
Pins 1-32OUTPUTS
Pins 35-36COMMON
Pin 37Earth ground 239-...
Note: External fusing or output protection recommended.
Note: External fusing or output protection recommended.
Fieldbus Electronics and I/O
D
FE
AB
C
L
K
J
GH
3/4 NPTF
www.asconumatics.eu X021-27-41
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
G2-2 Electronics • Spare Parts • End Plate with Terminal Strips
Description Weight Order CodeEnd plate with
terminal strip (1-16)
standard mount 0.200 239-1229End plate with
terminal strip (1-32)
standard mount 0.200 239-1231
End Plate with Terminal Strip for 1-16 (“AKF”) or 1-32 (“AKT”) Outputs
TERMINAL STRIP
Terminal 1-16OUTPUTS
Terminal comCOMMON
Earth ground
18 AWG WIRE MAXIMUM
239-...
A B C D E F G H J K L 57.9 25.4 7.4 75.8 58.9 10.9 6.4 61.0 40.1 74.9 29.0
Dimensions [mm]
TERMINAL STRIP
Terminal 1-32OUTPUTS
Terminal comCOMMON
Earth ground
18 AWG WIRE MAXIMUM
239-...
Clearance holefor M6 screw
Earth ground
Terminal 1-16DRIVE OF COILS
Conductorcross-sectionmax. 0.823 mm2
Terminal comCOMMON
Earth ground
Terminal 1-32DRIVE OF COILS
Conductorcross-sectionmax. 0.823 mm2
Terminal comCOMMON
Note: External fusing or output protection recommended.
Fieldbus Electronics and I/O
G
JH
F
C
B
A
DE
www.asconumatics.euX021-27-42
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
G2-2 Electronics • Spare Parts • End Plates with Round Connectors
End Plate with 12 pin (“P“), 19 pin (“Q”), 26 pin (“R”) or 12+26 pin (“S”) Round Connector
Description Weight Order approx. [kg] CodeEnd plate with 12 pin round connector
standard mount 0.210 239-2115End plate with 19 pin round connector
standard mount 0.210 239-2307End plate with 26 pin round connector
standard mount 0.210 239-1184End plate with 26+12 pin round connector
standard mount 0.210 239-1376
Pin 12 Earth ground
Pin 11COMMON
Pins 1-10DRIVE OF COILS
A B C D E F G H J3, 25.4 7.4 75.8 61.0 6.4 42.2 40.9 20.8 58.9
Dimensions [mm]
12 PIN ROUND CONNECTOR
Pins 1-10OUTPUTS 23-32
Pin 11COMMON
Pin 12Earth ground239-1376
26 PIN ROUND CONNECTOR
Pins 1-22OUTPUTS 1-22
Pins 24-25COMMON
Pin 26Earth ground239-1184239-1376
Clearance holefor M6 screw
Pin 26Earth ground
Pins 24-25COMMON
Pins 1-22DRIVE OF COILS
Note: External fusing or output protection recommended.
12 PIN ROUND CONNECTOR
Pins 1-8INPUTS
Pins 19-10COMMON
Pin 11not used
Pin 12Earth ground239-2115
Fieldbus Electronics and I/O
19 PIN ROUND CONNECTOR
Pin 1 = solenoid 15Pin 2 = solenoid 11Pin 3 = solenoid 7Pin 4 = solenoid 4Pin 5 = solenoid 3Pin 6 = COMMONPin 7 = solenoid 2Pin 8 = solenoid 6Pin 9 = solenoid 10Pin 10 = solenoid 14Pin 11 = solenoid 13Pin 12 = Earth groundPin 13 = solenoid 12Pin 14 = solenoid 8Pin 15 = solenoid 1Pin 16 = solenoid 5Pin 17 = solenoid 9Pin 18 = solenoid 16Pin 19 = not used
Manual Configuration Module (MCM)
Description Weight Order approx. [kg] Code
Complete MCM (incl. Pos. 1 to 10) 0.250 239-1384
www.asconumatics.eu X021-27-43
0049
6GB
-201
1/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
G2-2 Electronics • Spare Parts • Communication Module KitsCommunication Module Kit
Description Weight Order Code
approx. [kg]
Complete unit Allen-Bradley RIO (incl. Pos. 1 to 17) with 7/8” connector, standard (one housing) 0.790 239-1516
Complete unit Allen-Bradley RIO (incl. Pos. 1 to 17) with M12 connector (one housing) 0.790 239-1520
Complete unit Interbus -S M23 connector (one housing) 0.850 240-216
Complete unit ControlNet (two housings) 1.600 239-1841
Complete unit FIPIO Interface (two housings) 1.600 239-2310
Complete unit Fieldbus Foundation (H1 FF) (one housing) 0.790 240-217
Fieldbus Electronics and I/O
Valve Capability
Input Capability
Version Addressing Connector Order code
AS-Interface module
8 8 V2.1 Standard Vampire 240-156
16 16 V2.1 Standard Vampire 240-154
6 8 V2.1 Extended Vampire 240-222
12 16 V2.1 Extended Vampire 240-220
8 8 V3.0 Entended Vampire 240-232
16 16 V3.0 Entended Vampire 240-230
Input module 4*M12 240-142
G2-1 Electronics • Spare Parts • AS-Interface Module Kits
Single Sourcing Double Sourcing
OUTPUTMODULE
femalePin 1 = not usedPin 3 = (-) GNDPin 4 = output (sourcing)
0.5 A max.
INPUTMODULE
femalePin 1 = +24 VDCPin 2 = input 2 (sourcing)Pin 3 = (-) GNDPin 4 = input 1 (sourcing)
OUTPUTMODULE
female Pin 1 = not usedPin 2 = output 2 (sourcing)Pin 3 = (-) GND (Common)Pin 4 = output 1 (sourcing)
0.5 A max.
INPUTMODULE
femalePin 1 = +24 VDCPin 3 = (-) GNDPin 4 = input (sourcing)
I/O Pin Assignment
Accessory Description Order Code
5 pin straight male M12 connector 88100330
5 pin elbow male M12 connector 88161927
M12 plug 230-647
5 pin male DUO M12 connector for 2 inputs(2 cables, Ø3-5 mm) 88100253
G2-2 Electronics• I/O Module • Wiring Accessories
www.asconumatics.euX021-27-44
G2-2 Electronics • Spare Parts • M12 I/O Modules
8 M12 Wide Modulewith short-circuit protection
Fieldbus Electronics and I/O
Description Weight 16 Inputs 16 Outputsapprox. [kg] PNP NPN PNP
Complete unitsourcing PNP (incl. Pos. 1 to 10)
0.585 239-2500i
240-132i
239-1319i i
i With short-circuit protectioni i With short-circuit protection and status bit
0049
6GB
-201
1/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
www.asconumatics.eu X021-27-45
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
Fieldbus Electronics and I/O
Description Order Code LH cover, DIN rail only on request 239-1815LH standard cover on request 239-1816
Left Mounting Cover Assembly
G2-2 Electronics • Spare Parts • Cover Assemblies - Fuses
Description Order Code RH cover, DIN rail only on request 239-1873RH standard cover on request 239-1872
Right Mounting Cover Assembly
Plug-in Blade Terminal Fuse
Dimensions [mm]Description Rating (A) Littlefuse-
TypeA B C D E F Order Code
Blade terminal fuse, colour: pink 4 297 004 16.0 7,4 2,8 10.9 3,8 0.8 140-933
Blade terminal fuse, colour: red 10 297 010 16.0 7,4 2,8 10.9 3,8 0.8 140-934
Fuse
G3 Electronics • Spare Parts • M12 I/O ModulesCommunication module
Module d’Input / Output
Description Weight (g) Code
DeviceNet™ 255 240-180
EtherNet/IP™ 255 240-181
Modbus TCP/IP 255 240-292
Profibus DP 255 240-239
Profibus DP automobive version 255 240-301
Profinet® 255 240-240
Powerlink 255 240-239
Canopen® 255 240-291
DeviceLogix 255 240-293
E/S M12 Description CodeSignal type PNP NPN
Inputs
8 Inputs 240-206 240-210
8 Inputs + earth 240-295 -
16 Inputs 240-205 240-209
16 Inputs + earth 240-294 -
Outputs
8 Outputs PNP 240-208 -
16 Outputs PNP 240-207 -
8 Outputs PNP high current (1A) 240-300 -
Input and Output 8 Inputs & 8 Outputs 240-211 -
Terminal strip module Description CodeSignal type PNP NPN
Inputs 16 Inputs 240-203 240-204
Analog I/O 5-pin M12 Description CodeSignal type 0-10 VCC 4-20 mA
analog I/O4 Inputs 240-212 240-214
2 Inputs & 2 Outputs 240-213 240-215
Analog I/O for propor-tional valves
(SentronicPLUS)2 Inputs &t 2 Outputs 240-307 -
www.asconumatics.euX021-27-46
0049
6GB
-200
8/R
01A
vaila
bilit
y, d
esig
n an
d sp
ecifi
catio
ns a
re s
ubje
ct to
cha
nge
with
out n
otic
e. A
ll rig
hts
rese
rved
.
Fieldbus Electronics and I/O
Top Related