Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.Printed in U.S.A. Form 50JC-4-6-01SB Pg 1 6-21 Replaces: NEW
50JC WEATHEREXPERT® SERIES VARIABLE SPEED
SINGLE PACKAGE ROOFTOPWITH ECOBLUE™ TECHNOLOGY
COOLING UNITS WITH OPTIONAL ELECTRIC HEAT
— PERFORMANCE DATA
— CERTIFIED DIMENSION PRINTS
— CERTIFIED ROOF CURB DETAILS
2
JOB NAME: LOCATION:
BUYER: BUYER PO #: CARRIER#:
UNIT NUMBER: MODEL NUMBER:
PERFORMANCE DATA CERTIFIED BY:
DESCRIPTION50JC units are ultra high-efficiency single-packaged variable speed electric cooling, electric heating units that are pre-wiredand pre-charged with Puron® (R-410A) HFC refrigerant. Electric heat is available as a field-installed accessory. The units arefactory tested in the cooling mode. All size 04-06 models use variable speed cooling capacity control.
FEATURESStandard Base Unit• Puron (R-410A) HFC refrigerant• SEERs up to 20.0• Exceeds ASHRAE (American Society of Heating,
Refrigerating, and Air-Conditioning Engineers) 90.1-2016 and IECC* (International Energy Conservation Code) IECC-2015 minimum efficiency requirements
• Rated in accordance with AHRI Standards 210/240• Designed in accordance with Underwriters Laboratories
Std 1995 and listed by UL and UL-Canada• Corrosive resistant composite sloping design; side or
center drain condensate pan. Meets ASHRAE Standard 62
• Cooling operating range from 0°F (-18°C) up to 125°F (52°C)
• Field convertible from vertical to horizontal airflow for slab mounting — no special kits required
• Two-inch disposable return air filters.• Thru-the-bottom power entry capability• Single point two-stage electric connections• 24-volt control circuit protected with resettable circuit
breaker• Direct Drive — EcoBlue™ Technology Indoor fan sys-
tem uses Vane Axial fan design and electronically com-mutated motor
– Shall have inherent automatic-reset thermal overloadprotection
– Shall require no fan/motor belts for operation, adjust-ments, and/or initial fan speed setup.
– Shall be internally protected from electrical phase reversaland loss
– Shall have slow ramp up to speed control capabilities tohelp reduce sound and comfort issues
– Shall be a slide-out design with two screw removal• All sizes have variable speed cooling capacity control
that ranges from 25% up to 105% of normal unit capac-ity
• Totally enclosed variable speed condenser motors with permanently lubricated bearings
• Low-pressure and high-pressure switches• Full perimeter base rail with built-in rigging adapters
and fork truck slotsSystemVu™ controls are standard on each unit to helpfacilitate units' diagnostics, ease of commissioning, controlthe cooling, heating, ventilation operation and much more.Some highlights: • Large full text - multi line display• SB Flash Port for data transfer• Built in i-Vu®, CCN and BACnet†
• Built in electrical phase and compressor reverse rotation protection
• Read refrigerant pressure from display- no gauges required
• Quick LED Status - Run, Alert, Fault• Conventional thermostat or sensor capabilities• Historical component runtime and starts• Supply Air Tempering and Demand Limiting control• Equipment / System Touch Compatibility• Supports linkage on zoning systems using CCN VVT
and i-Vu Open VVT controlsCabinet• Access panels with easy grip handles and NO-STRIP
screw collar• Pre-painted exterior panels and primer-coated interior
panels tested to 500 hours salt spray protection• Tool-less filter access door• Cabinet insulated with foil faced insulation that is
encapsulated/taped throughout the indoor air streamRefrigerant System• TXV refrigerant metering device• Liquid line filter drier• Scroll compressors with internal line-break overload
protection• Copper tube, aluminum fin coils with optional corrosion
resistant coils.• Removable gage line plugs for reading refrigerant pres-
sure with unit panels in placeStandard Limited Parts Warranty• 5-year electric heater parts (field-installed)• 5-year compressor parts• 5-year Ultra Low Leak economizer parts (factory-
installed)• 3-year SystemVu™ controls• 1-year parts
* IECC is a registered trademark of International Code Council, Inc.† BACnet is a registered trademark of ASHRAE.
3
PERFORMANCE DATA
Unit Operating Weight ____________________________ lbCOOLING (ELECTRIC)Gross Total Capacity ___________________________ Btuh at Condenser Air Temperature _________________ °FGross Sensible Capacity ________________________ BtuhCompressor Power Input ________________________ kWIndoor Entering: db ___________ °F / wb ___________ °FAirflow _____ CFM External Static Pressure ______ in. wgIndoor Fan Motor Size ___________________________ HPIndoor Fan Motor Setting ________________________ Vdc
Exhaust Fan Motor Size _________________________ HPCurb Weight ___________________________________ lbHEATING (ELECTRIC)Heating Capacity: Stage 1 ____________________________________ BtuhStage 2 ____________________________________ BtuhHeating Capacity Total _______________________ BtuhStage 1 ____________________________________ kWStage 2 ____________________________________ kWHeating Capacity Total _______________________ kW
ELECTRICAL DATA
Power Supply to Unit ______________________________Volts ___________________________________________Phase ___________________________________________ HzMaximum Circuit Amps ____________________________Maximum Overcurrent Protection ____________________
SUBMITTAL DATA
Job Name _______________________________________Architect ________________________________________Engineer _______________________________________Contractor _______________________________________Unit Designation __________________________________
® ®
4
FACTORY-INSTALLED OPTIONS
Economizer with DRY BULB Sensing and BarometricRelief*Low Leak Air Dampers —
Models with SystemVu™ controller meet CaliforniaTitle 24-2016 (Section 120.2) Fault Detection and Di-agnostic (FDD) requirements (EconoMi$er 2 sys-tem).
Economizer with ENTHALPY Sensing and BarometricRelief*Low Leak Air Dampers —
Models with SystemVu controller meet California Ti-tle 24-2016 (Section 120.2) Fault Detection and Di-agnostic (FDD) requirements (EconoMi$er 2 sys-tem).
Economizer with DRY BULB Sensing and BarometricRelief*ULTRA LOW LEAK Air Dampers —
Models with SystemVu meet California EnergyCommission Title 24-2016 prescriptive section140.4 (damper leakage etc.) and mandatory section120.2.i for Fault Detection and Diagnostic require-ments. Economizers meet ASHRAE 90.1-2016damper leakage requirements as stated in section6.5.1.1.4 and Table 6.4.3.4.3, and meet 2016 FaultDetection and Diagnosis requirements in section6.4.3.12. Economizers meet IECC-2012 sectionC402.4.5.2 and IECC-2015 sections C403.2.4.3and C403.3.3.5 for outside air, return air, and reliefair damper leakage requirements and IECC-2015section C403.2.4.7 for Fault Detection and
Diagnostic requirements. NOTE: IECC-2015 section C403.2.4.7.1 requiresdifferential return air sensor, which must be or-dered separately.Outside air and return air (volume) dampers areAMCA rated — plus 5 year limited parts warranty(EconoMi$er 2 system).
Economizer with ENTHALPY Sensing and BarometricRelief*ULTRA LOW LEAK Air Dampers —
Models with SystemVu meet California EnergyCommission Title 24-2016 prescriptive section140.4 (damper leakage etc.) and mandatory section120.2.i for Fault Detection and Diagnostic require-ments. Economizers meet ASHRAE 90.1-2016damper leakage requirements as stated in section6.5.1.1.4 and Table 6.4.3.4.3, and meet 2016 FaultDetection and Diagnosis requirements in section6.4.3.12. Economizers meet IECC-2012 sectionC402.4.5.2 and IECC-2015 sections C403.2.4.3and C403.3.3.5 for outside air, return air, and reliefair damper leakage requirements and IECC-2015section C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC-2015 section C403.2.4.7.1 requiresdifferential return air sensor, which must be or-dered separately.Outside air and return air (volume) dampers areAMCA rated — plus 5 year limited parts warranty(EconoMi$er 2 system).
5
FACTORY-INSTALLED OPTIONS (CONT)
Through the base connectors for electric conduit Humidi-MiZer® adaptive dehumidification system
(this option also includes low ambient controls) Electric heaters and single point electrical point kits. HACR circuit breaker Non-fused disconnect Powered 115-volt convenience outlet Non-powered 115-volt convenience outlet High static evaporator fan motor Return air smoke detector Supply air smoke detector CO2 Sensor
Special coating protection for evaporator and con-denser coils
MERV-8 return air filters Phase monitor protection Condensate overflow switch Hinged access panels for easy unit access Condenser hail guard - louvered style Cu/Cu coils
Optional Warranties Complete unit parts only, up to 5 years Complete unit parts and labor, up to 5 years
Many other optional warranties are available. See theCommercial Start-Up and Optional Extended War-ranty Price pages for further information.
6
FIELD-INSTALLED ACCESSORIES
Economizer with DRY BULB Sensing and BarometricReliefLow Leak Air Dampers —
Models with SystemVu™ controller meet CaliforniaTitle 24-2016 Section 120.2.i Fault Detection and Di-agnostic (FDD) requirements (EconoMi$er 2 sys-tem).
Economizer with ENTHALPY Sensing and BarometricReliefLow Leak Air Dampers —
Models with SystemVu controller meet California Ti-tle 24-2016 Section 120.2.i Fault Detection and Diag-nostic (FDD) requirements (EconoMi$er 2 system).
Economizer with DRY BULB Sensing and BarometricReliefULTRA LOW LEAK Air Dampers —
Models with SystemVu meet California EnergyCommission Title 24-2016 prescriptive section 140.4(damper leakage etc.) and mandatory section 120.2.ifor Fault Detection and Diagnostic requirements.Economizers meet ASHRAE 90.1-2016 damperleakage requirements as stated in section 6.5.1.1.4and Table 6.4.3.4.3, and meet 2016 Fault Detectionand Diagnosis requirements in section 6.4.3.12.Economizers meet IECC-2012 section C402.4.5.2and IECC-2015 sections C403.2.4.3 and C403.3.3.5for outside air, return air, and relief air damper leak-age requirements and IECC-2015 section C403.2.4.7for Fault Detection and Diagnostic requirements.
NOTE: IECC-2015 section C403.2.4.7.1 requires dif-ferential return air sensor, which must be ordered sep-arately.Outside air, return air, and relief air (volume) damp-ers are AMCA rated — plus 5 year limited parts war-ranty (EconoMi$er 2 system).
Economizer with ENTHALPY Sensing and BarometricRelief (cont)ULTRA LOW LEAK Air Dampers —
Models with SystemVu meet California EnergyCommission Title 24-2016 prescriptive section140.4 (damper leakage etc.) and mandatory section120.2.i for Fault Detection and Diagnostic require-ments. Economizers meet ASHRAE 90.1-2016damper leakage requirements as stated in section6.5.1.1.4 and Table 6.4.3.4.3, and meet 2016 FaultDetection and Diagnosis requirements in section6.4.3.12. Economizers meet IECC-2012 sectionC402.4.5.2 and IECC-2015 sections C403.2.4.3and C403.3.3.5 for outside air, return air, and reliefair damper leakage requirements and IECC-2015section C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC-2015 section C403.2.4.7.1 requiresdifferential return air sensor, which must be or-dered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty. (EconoMi$er 2 system).
7
FIELD-INSTALLED ACCESSORIES (CONT)
Electric heater(s) Power exhaust — prop fan design Two-position motorized outdoor air damper Manual outside air damper 25% Manual outside air damper 50% Roof curb — 14 inch (356 mm) tall Roof curb — 24 inch (610 mm) tall Thru-the-bottom connections, electrical Condenser hail guard, louvered style Phase monitor (loss of phase/phase reversal) 115v 20 Amp non unit powered convenience
outlet kit
Condensate overflow switch Thermostats and sensors
NOTE: These models have variable speed cooling capability, use appropriate thermostat.
Economizer Sensors Single dry bulb control Differential dry bulb control Single enthalpy control Differential enthalpy control CO2 — wall mounted CO2 — duct mounted CO2 — unit mounted
8
Fig
. 1 —
50J
C**
04-0
6 B
ase
Un
it D
imen
sio
ns
UN
IT D
IME
NS
ION
PR
INT
9
Fig
. 1 —
50J
C**
04-0
6 B
ase
Un
it D
imen
sio
ns
(co
nt)
UN
IT D
IME
NS
ION
PR
INT
10
Fig
. 1 —
50J
C**
04-0
6 B
ase
Un
it D
imen
sio
ns
(co
nt)
UN
IT D
IME
NS
ION
PR
INT
11
AC
CE
SS
OR
Y D
IME
NS
ION
PR
INT
Fig
. 2 —
50J
C**
04-0
6 B
ase
Un
it D
imen
sio
ns
EE
7/16
"[1
1]
4 9/
16"
[115
.5]
1/4"
[7.0
]
5' 7
-3/8
"[1
711.
3]
1' 4
-13/
16"
[4
27] I
NSI
DE
1-3/
4"[4
4.4]
2-3/
8"[6
1]
1-3/
4"[4
4.5]
1.00
"[2
5.4]
"A"
1-3/
4"[4
4.4]
21.7
4"[5
52.2
]5.42
"[1
37.7
]11
.96"
[303
.8]
4.96
"[1
26.0
]70
.87"
[180
0.2]
40.6
9"[1
033.
5]
21.8
4"[5
54.7
]
16.0
3"[4
07.2
]
1.75
"[4
4.5]
20.4
1"[5
18.3
]3.
00"
[76.
2]13
.78"
[350
.0]
14.0
0"[3
55.6
]
3.00
"[7
6.2]
15.1
9"[3
85.8
]
32.1
9"[8
17.6
]
3'-1
3/1
6"[9
44.6
]
"A"
1-3/
4"[4
4.5]
CR
BTM
PWR
001A
013/
4" [1
9] N
PT3/
4" [1
9] N
PT1/
2" [1
2.7]
NPT
CR
RFC
UR
B002
A01
CO
NN
ECTO
R P
KG. A
CC
.G
AS C
ON
NEC
TIO
N T
YPE
GAS
FIT
TIN
GPO
WER
WIR
ING
FI
TTIN
GC
ON
TRO
L W
IRIN
G
FITT
ING
ACC
ESSO
RY
CO
NVE
NIE
NC
E O
UTL
ET W
IRIN
G C
ON
NEC
TOR
THR
U T
HE
CU
RB
1/2"
[12.
7] N
PT1/
2" [1
2.7]
NPT
CR
BTM
PWR
003A
01TH
RU
TH
E BO
TTO
M
RO
OF
CU
RB
ACC
ESSO
RY
#A
CR
RFC
UR
B001
A01
14"
[356
]
24"
[610
]
ECN
NO
.AP
P'D
CH
K'D
BYD
ATE
REV
ISIO
N R
ECO
RD
REV
1067
898
--
MM
C04
/22/
13O
VER
ALL
DIM
. 5'-7
3/8
" WAS
5'-7
7/8
; 18G
A M
ATER
IAL
WA
16 G
A.; N
AIL
FIEL
D S
UPP
LIED
WAS
W
ITH
CU
RB
A
DR
AWIN
G R
ELEA
SE L
EVEL
:PR
OD
UC
TIO
NTH
IRD
AN
GLE
PRO
JEC
TIO
N
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
DD
IMEN
SIO
NS
ARE
IN IN
CH
ESTO
LER
ANC
ES O
N:
1 D
EC2
DEC
3 D
ECAN
GM
ATER
IAL
--
--
- - -
AUTH
OR
IZAT
ION
NU
MBE
RTI
TLE
1041
738
CU
RB
ASY,
RO
OF
ENG
INEE
RIN
GM
ANU
FAC
TUR
ING
ENG
INEE
RIN
G R
EQU
IREM
ENTS
--
--
SIZE
DR
AWIN
G N
UM
BER
REV
T-00
5, Y
-002
DR
AFTE
RC
HEC
KER
D48
TC40
0427
BW
EIG
HT:
-M
MC
06/1
7/11
--
SHEE
T 5
OF
5
SUR
FAC
E FI
NIS
HM
FG/P
UR
CH
MO
DEL
(IN
TER
NAL
USE
ON
LY)
NEX
T D
RAW
ING
SCAL
ED
ISTR
IBU
TIO
N
-PU
RC
H-
N/A
MM
C
NO
TES:
1. R
OO
FCU
RB
ACC
ESSO
RY
IS S
HIP
PED
DIS
ASSE
MBL
ED.
2. IN
SULA
TED
PAN
ELS:
25.
4 [1
"] TH
K. P
OLY
UR
ETH
ANE
FOAM
, 44.
5 [1
-3/4
] # D
ENSI
TY.
3. D
IMEN
SIO
NS
IN [
] AR
E IN
MIL
LIM
ETER
S.4.
RO
OFC
UR
B: 1
8 G
AGE
STEE
L.5.
ATT
ACH
DU
CTW
OR
K TO
CU
RB.
(FLA
NG
ES O
F D
UC
T R
EST
ON
CU
RB)
.6.
SER
VIC
E C
LEAR
ANC
E 4
FEET
ON
EAC
H S
IDE.
7.
DIR
ECTI
ON
OF
AIR
FLO
W.
8. C
ON
NEC
TOR
PAC
KAG
E C
RBT
MPW
R00
1A01
IS F
OR
TH
RU
-TH
E-C
UR
B G
AS T
YPE
P
ACKA
GE
CR
BTM
PWR
003A
01 IS
FO
R T
HR
U-T
HE-
BOTT
OM
TYP
E G
AS C
ON
NEC
TIO
NS.
TYPI
CAL
(4) S
IDES
SUPP
LY A
IRR
ETU
RN
AIR
RO
OFI
NG
MAT
ERIA
L(F
IELD
SU
PPLI
ED)
CAN
T ST
RIP
(FIE
LD S
UPP
LIED
)
RO
OFI
NG
FEL
T(F
IELD
SU
PPLI
ED)
CO
UN
TER
FLA
SHIN
G(F
IELD
SU
PPLI
ED)
UN
ITG
ASKE
T(S
UPP
LIED
WIT
H C
UR
B)
RIG
ID IN
SULA
TIO
N(F
IELD
SU
PPLI
ED)
DU
CT
(FIE
LD S
UPP
LIED
)
NAI
L (F
IELD
SU
PPLI
ED)
CER
TIFI
ED D
RAW
ING
VIEW
"B"
CO
RN
ER D
ETAI
L
SEE
VIEW
"B"
RET
UR
N A
IRSU
PPLY
AIR
SUPP
LY A
IRO
PEN
ING
RET
UR
N A
IRO
PEN
ING
GAS
SER
VIC
E PL
ATE
THR
U T
HE
CU
RB
DR
ILL
HO
LE
2"
[50.
8] @
AS
SEM
BLY
(IF
REQ
UIR
ED)
(SEE
NO
TE #
8)
SEE
NO
TE #
2
11 3
/4"[2
98.5
] WID
EIN
SULA
TED
DEC
K PA
NEL
S
8 9/
16"[2
17.5
] WID
EIN
SULA
TED
DEC
K PA
NEL
1/3/
4"[4
4.5]
SCAL
E 0
.250
E-E
SEC
TIO
N
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.Printed in U.S.A. Form 50JC-4-6-01SB Pg 12 6-21 Replaces:NEW
© 2021 Carrier
Top Related