Thank you for purchasing a Futaba 3PM-2.4GHz system.Before using your 3PM-2.4GHz system, read this manual carefully in order to use your R/C set safely.
After reading this manual, store it in a safe place.
Application, Export, and Modification1. This product may be used for models only. It is not intended for use in any application other than thecontrol of models for hobby and recreational purposes.
2. Exportation precautions:(a) When this product is exported from the country of manufacture, its use is to be approved by the laws govern-ing the country of destination for devices that emit radio frequencies. If this product is then re-exported to othercountries, it may be subject to restrictions on such export. Prior approval of the appropriate goverment authori-ties may be required. If you have purchased this product from an exporter outside your country, and not theauthorized Futaba distributor in your country, please contact the seller immediately to determine if such exportregulations have been met.(b) Use of this product with other than models may be restricted by Export and Trade Control Regulations, andan application for export approval must be submitted.
3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorizedmodification, adjustment, and replacement of parts on this product. Any such changes may void thewarranty.
Compliance Information Statement (for U.S.A.)This device, trade name Futaba Corporation of America, model number R603FF, complies with part15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesiredoperation.
The responsible party of this device compliance is:Futaba Service Center3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.TEL (217)398-8970 or E-mail: [email protected] (Support)TEL (217)398-0007 or E-mail: [email protected] (Service)
Battery Recycling (for U.S.A.)The RBRCTM SEAL on the (easily removable) nickel-cadmium battery contained inFutaba products indicates that Futaba Corporation of America is voluntarily participatingin an industry program to collect and recycle these batteries at the end of their usefullives, when taken out of service within the United States. The RBRCTM program providesa convenient alternative to placing used nickel-cadmium batteries into the trash or mu-nicipal waste system, which is illegal in some areas.
You may contact your local recycling center for information on where to return the spent battery.Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Futaba Cor-poration of America's involvement in this program is part of its commitment to protecting our environ-ment and conserving natural resources.
RBRCTM is a trademark of the Rechargeable Battery Recycling Corporation.
Warning: This product contains a chemical known to cause cancer and birth defects (or otherreproductive harm).
•No part of this manual may be reproduced in any form without prior permission.•The contents of this manual are subject to change without prior notice.•This manual has been carefully written. Please write to Futaba if you feel that any corrections or clarificationsshould be made.
•Futaba is not responsible for the use of this product.
4
For Your Safety As Well As That Of Others...........6Explanation of Symbols ................................................................................ 62.4GHz System Precautions ......................................................................... 6Operation Precautions .................................................................................. 7NiCd Battery Handling Precautions ............................................................. 9Storage and Disposal Precautions ............................................................ 10Other Precautions ....................................................................................... 11
Table Of Contents
Before Using ...........................................................12Features........................................................................................................ 12Set Contents ................................................................................................ 14Nomenclature (Transmitter/Receiver/Servo) ............................................ 15
Installation ..............................................................22Receiver and Servo Connections .............................................................. 22Installation Safety Precautions .................................................................. 22
Initial Set-Up ...........................................................24How to link the transmitter and the receiver............................................. 24How to set the F/S position (PPM mode)................................................... 24Preparations (Transmitter) ......................................................................... 25
Functions ................................................................30End Point Adjuster ...................................................................................... 30Steering Speed ............................................................................................ 33Steering EXP / Throttle EXP ....................................................................... 34A.B.S. Function ............................................................................................ 36Throttle Acceleration................................................................................... 38Brake Mixing ................................................................................................ 40Programmable Mixing ................................................................................. 41Fail Safe/Battery Fail Safe (HRS mode) ..................................................... 42Trim ............................................................................................................... 43Steering D/R ................................................................................................. 44ATL Function ............................................................................................... 44Channel 3 Position ...................................................................................... 45Subtrim ......................................................................................................... 46
Function Map ..........................................................28(Function Selection) .................................................................................... 28
5
Channel Reverse ............................................................................... 47Model Select ...................................................................................... 48Timer................................................................................................... 49
(System Functions)Model Copy ........................................................................................ 51Model Reset ....................................................................................... 52Model Name ....................................................................................... 52HRS/PPM Select ................................................................................ 53Function Select Switch ..................................................................... 54Function Select Lever ....................................................................... 55Condition 2 Selection........................................................................ 56LED Mode Selection .......................................................................... 56
For Your SafetyAs Well As
That Of Others
BeforeUsing
Installation
InitialSet-Up
FunctionMap
Functions
Reference
Reference .........................................................57Ratings ............................................................................................... 57Optional Parts .................................................................................... 58Troubleshooting ................................................................................ 59Error Displays .................................................................................... 60When requesting repair .................................................................... 61
6
Fo
r Yo
ur S
afety As W
ell As T
hat O
f Oth
ers
For Your Safety As Well As That Of Others
Use this product in a safe manner. Please observe the following safety precautions atall times.
Explanation of SymbolsThe parts of this manual indicated by the following symbols are extremely importantand must be observed.
DangerIndicates a procedure which could lead to a dangerous situ-ation and may cause death or serious injury if ignored andnot performed properly.
WarningIndicates procedures which may lead to dangerous situa-tions and could cause death or serious injury as well as su-perficial injury and physical damage.
Caution Indicates procedures that may not cause serious injury, butcould lead to physical damage.
Symbols: ; Prohibited ; Mandatory
Symbols Explanation
Special attention should be paid before turning on the system while other cars are run-ning or other airplanes are flying because the 2.4GHz RC system could potentially af-fect them.
Warning
2.4GHz System Precautions
Prohibited Procedures
Always use R603FF under the following conditions;Power supply: 6V Nicd battery (PPM/HRS mode)Servo: 6V type Futaba Digital Servo (HRS mode)
If these conditions are not followed, control may be impossible or the servo may be damaged.
CautionMandatory Procedures
7
Fo
r Y
ou
r S
afet
y A
s W
ell A
s T
hat
Of
Oth
ers
Operation Precautions
WarningProhibited Procedures
Do not operate outdoors on rainydays , run through puddles of water,or use when visibility is limited.
Should any type of moisture (water or snow) enter anycomponent of the system, erratic operation and lossof control may occur.
Do not operate in the followingplaces.
-Near people or roads.
-On any pond when boats are present.
-Near high tension power lines or communi-cation broadcasting antennas.
Interference could cause loss of control. Improper in-stallation of your Radio Control System in your modelcould result in serious injury.Do not operate this R/C system when
you are tired, not feeling well or underthe influence of alcohol or drugs.
Your judgment is impaired and could result in a dan-gerous situation that may cause serious injury to your-self as well as others.
Mandatory Procedures
Adjust the antenna vertically to the ground.
Otherwise, the operating range may become shorter.
Always perform an operating range check prior to use.
Problems with the radio control system as well as improper installation in a model could cause loss of control.
Simple range test method;Have a friend hold the model, or clamp it down or place it where the wheels or prop cannot come in contact with anyobject. Walk away and check to see if the servos follow the movement of the controls on the transmitter. Should younotice any abnormal operation, do not operate the model. Also check to be sure the model memory matches themodel in use.
CautionProhibited Procedures
Do not touch the engine, motor, speed control orany part of the model that will generate heat whilethe model is operating or immediately after its use.
These parts may be very hot and can cause serious burns.
Never hold only the an-tenna.
Hold the grip handle, otherwise theantenna may be damaged.
Mandatory Procedures
When making adjustments to the model, do so with the engine not running or the motordisconnected.
You may unexpectedly lose control and create a dangerous situation.
8
Fo
r Yo
ur S
afety As W
ell As T
hat O
f Oth
ers
(Turning on the power switches)Always check the throttle trigger on the transmitter to be sure it is at the neutral position.
1. Turn on the transmitter power switch.
2. Turn on the receiver or speed control power switch.
(Turning off the power switches)Always be sure the engine is not running or the motor is stopped.
1. Turn off the receiver or speed control power switch.
2. Then turn off the transmitter power switch.
If the power switches are turned off in the opposite order the model may unexpectedly run out of control and causea very dangerous situation.
(Fail safe function) ---when using HRS modeBefore running (cruising), check the fail safe function.
Check Method:
Before starting the engine, check the fail safe function as follows:
1. Turn on the transmitter and receiver power switches.
2. Wait at least one minute, then turn off the transmitter power switch. (The transmitter automatically transfers the failsafe data to the receiver every minute.)
3. Check if the fail safe function moves the servos to the preset position when reception fails.
The fail safe function is a safety feature that minimizes set damage by moving the servos to a preset position whenreception fails. However, if set to a dangerous position, it has the opposite effect.
Setting example: Throttle idle or brake position
(Fail safe function) ---when using PPM modeAlways set the F/S position after turning on the transmitter power.
F/S Position Setting Method:
Move and hold the throttle trigger to the F/S servo position where you want to set (Throttle idle or brake position).Then push the F/S switch on the transmitter. The LED blinks green.
9
Fo
r Y
ou
r S
afet
y A
s W
ell A
s T
hat
Of
Oth
ers
NiCd Battery Handling Precautions (Only when NiCd batteries are used)
WarningMandatory Procedures
Always check to be sure your batter-ies have been charged prior to oper-ating the model.
Should the battery go dead while the model is operat-ing, loss of control will occur and create a very dan-gerous situation.
To recharge the transmitter and/or re-ceiver NiCd batteries, use the specialcharger made for this purpose.
Overcharging could cause the NiCd battery to over-heat, leak or explode. This may lead to fire, burns,loss of sight and many other types of injuries.
CautionProhibited Items
Do not use commercial AAsize NiCd batteries.
Quick charging may cause thebattery contacts to overheat anddamage the battery holder.
Do not short circuit the NiCd batteryterminals.
Causing a short circuit across the battery terminalsmay result in abnormal heating, fire and burns.
Do not drop the NiCd battery or ex-pose it to strong shocks or vibrations.
The battery may short circuit and overheat. Electrolytemay leak out and cause burns or chemical damage.
When the model is not being used,always remove or disconnect theNiCd battery.
Leaving the battery connected could create a dangeroussituation if someone accidentally turns on the receiverpower switch. Loss of control would occur.
SpecialCharger
ShockProhibited
NiCd AA sizebatteries.
Useprohibited
Do not throw NiCd batteries into afire. Do not expose NiCd batteries toextreme heat. Also do not disas-semble or modify a NiCd batterypack.
Overheating and breakage will cause the electrolyteto leak from the cells and cause skin burns, loss ofsight as well as other injuries.
When the system will not be used forany length of time store the systemwith batteries in a discharged state.Be sure to recharge the batteries priorto the next time the system is used.
If the batteries are repeatedly recharged in a slightlydischarged state the memory effect of the NiCd bat-tery may considerably reduce the capacity. A reduc-tion in operating time will occur even when the batter-ies are charged for the recommended time.
<NiCd Battery Electrolyte>The electrolyte in NiCd batteries is a strong alkali. Should you get even the smallest amount of theelectrolyte in your eyes, DO NOT RUB. Wash immediately with water and seek medical attention atonce. The electrolyte can cause blindness. If electrolyte comes in contact with your skin or clothes,wash with water immediately.
Prohibited Items
10
Fo
r Yo
ur S
afety As W
ell As T
hat O
f Oth
ers
Storage and Disposal Precautions
WarningProhibited Procedures
Do not leave the radio system or models within the reach of small children.
A small child may accidentally operate the system. This could cause a dangerous situation and injuries. NiCdbatteries can be very dangerous when mishandled and cause chemical damage.
CautionProhibited Procedures
Do not store your R/C system in thefollowing places.
- Where it is extremely hot or cold.
- Where the system will be exposed to directsunlight.
- Where the humidity is high.
-Where vibration is prevalent.
-Where dust is prevalent.
-Where the system would be exposed tosteam and condensation.
Storing your R/C system under adverse conditionscould cause deformation and numerous problemswith operations.
Mandatory Procedure
If the system will not be used for along period of time, remove the bat-teries from the transmitter and modeland store in a cool, dry place.
If the batteries are left in the transmitter, electrolytemay leak and damage the transmitter. This applies tothe model also. Remove the batteries from it also toprevent damage.
<NiCd Battery Recycling>A used NiCd battery is valuable resource. Insulate the battery terminals and dispose of the battery bytaking it to a battery recycling center.
11
Fo
r Y
ou
r S
afet
y A
s W
ell A
s T
hat
Of
Oth
ers
Other Precautions
CautionProhibited Procedures
Do not expose plastic parts to fuel,motor spray, waste oil or exhaust.
The fuel, motor spray, waste oil and exhaust will pen-etrate and damage the plastic.
Always use only genuine Futabatransmitters, receivers, servos, FETa m p s ( e l e c t r o n i c s p e e dcontrols),NiCd batteries and other op-tional accessories.
Futaba will not be responsible for problems caused bythe use of other than genuine Futaba parts. Use theparts specified in the instruction manual and catalog.
Mandatory Procedures
12
Befo
re Using
This system is based on the combination of the newly developed 2.4GHz transmitterand its corresponding receiver. The system utilizes the 2.4GHz-SS radio communica-tion and an ultra small antenna. In addition, the system inherits Futaba's unique HRS(High Response System).
- 2.4GHzSS (Spread Spectrum) radio communication system- Frequency channel setting unnecessarySifting the channels within the 2.4GHz band automatically, this system minimizesthe interference from other 2.4GHz systems.- Accepts no unwanted signals by using ID code- The function "Auto-Detect" is utilized to automatically determine which modeis active, HRS or PPM mode. (R603FF)- Short and small antenna (T3PM-2.4G)- Simple segment type LCD display and four edit keys for easy data setup- 10 model memoryModel names can use up to 3 letters, numbers, and symbols so that easily understoodnames can be set. Model copy function simplifies creation of a model memory withdifferent fine setups.- Two function groups: Frequently used functions / System functionsFrequently used functions can be easily called from the initial screen with Select Key(SEL).- Brake mixing for large cars (BMX)Brake mixing of the front and rear wheels of 1/5GP cars, etc. has balance adjustmentfunctions.- Steering dual rate (D/R-ST)Steering angle can be adjusted with digital trim lever.- Anti-skid Braking System (ABS)This function applies the brakes so that the tires of gasoline engine cars, etc. do notlose their grip on the road even when braking at corners.- Throttle acceleration (ACC)Gasoline engine cars have a time lag before the clutch and brakes are connected. TheACC function minimizes this time lag.- Steering speed (SPD)When you sense that the steering servo is too fast, etc., the servo operating speed(direction that suppresses the maximum speed) can be adjusted.- Racing timer (TIMER) : Up timer or Down timer can be selected.A lap time can record 100 lap times and the total time. The timer can also be startedautomatically by trigger operation. The race time can be set.
Before Using
Features
13
Bef
ore
Usi
ng
- Digital trim: Steering trim, Throttle trim, Steering D/RThe current position is displayed on the LCD screen for about three seconds wheneach digital trim is operated.- Function select lever function (FNC-DT1/DT2/DT3/DT4)This function assigns a function to levers (digital trims, grip levers). Trim positioningat each model call is unnecessary because all the levers are digital.- Function select switch function (FNC-SW1/SW2)This function assigns a function to the two installed switches.- Condition 2 SelectionIn specific functions, two rates can be set up, and switched with SW1 switch simulta-neously during a run.- NEW design considers operability and weight balance- Tension adjustment functionThe wheel tension can be adjusted from the outside.- Trigger stopper function (Mechanical ATL)- High luminosity blue LED pilot lampYou can select your desired brightness of the pilot lamp. (Four steps)
14
Befo
re Using
Set ContentsYour 3PM 2.4GHz system includes the following:
- If any of the set contents are missing, or you have any questions, please contact thedealer where the unit was purchased.
Transmitter T3PM-2.4G
Receiver R603FF
MiscellaneousTransmitter battery holder
Receiver switchInstruction manual
Always use only genuine Futaba transmitter, receiver, FET amp, NiCd battery and otheroptional parts.
Futaba will not be responsible for damage caused by other than genuine Futaba parts and components. Use onlythe genuine Futaba parts and components listed in the instruction manual and catalog.
Caution
Always use R603FF under the following conditions:Power supply: 6V NiCd battery (PPM/HRS mode)Servo: 6V type Futaba Digital Servo (HRS mode)
If the conditions are different, control is impossible or the servo may be damaged.
Caution
3PM 2.4GHz system
15
Bef
ore
Usi
ng
Transmitter T3PM-2.4GNomenclature
Throttle trim (DT2)
Edit keys
LCD screen
Pilot lamp
CH3 switch ( SW2)
(See page 16 for the operatinginstructions.)
Steering dual ratelever (DT3)
(See page 16 for the operatinginstructions.)
ATL lever (DT4)(See page 16 for the operating
instructions.)
Antenna
Power switch
Steering trim (DT1)
(See page 16 for theoperating instructions.)
Mechanical ATLadjusting screw(See page 17 for theadjustment instructions.)
Steering wheel
Throttletrigger
Grip Handle
Push switch (SW1)
*The switches and levers in the figure are shown in the initial setting position.
Precautions when turning the power switch on and off.When the data is changed using the edit keys or trim levers, wait at least twoseconds before turning off the power. If the power is turned off within twoseconds after the data was changed, the new data will not be written to memory.
Never hold the antenna alone.
Hold the grip handle. Otherwise the antenna may be damaged.
Caution
16
Befo
re Using
Digital Trim Operation(Initial settings: DT1: Steering trim, DT2: Throttle trim)
Push the lever to the left or right (up or down).The current position is displayed on the LCD screen for about three seconds wheneach digital trim is operated.
Steering trimposition
Throttle trimposition
- Each step is indicated by a tone.- When the trim exceeds the maximum trim adjustmentrange, the tone will change pitch and the lever will notmove any farther.
Trim OperationWith the digital trim feature, trim adjustments have no effect on the maximum servotravel. This prevents the linkages from binding when adjustments are made.
DT2
DT1
Grip lever operation(Initial settings: DT3=Steering D/R, DT4=Throttle ATL)
Push the lever to the left or right. The current set value is displayed on the LCDscreen for about three seconds when each lever is operated.
(Antenna Moving Range)
Adjustment of the antenna direction
Adjust the antenna vertically to the ground.
Otherwise, the operating range may become shorter.
Warning
Antenna
17
Bef
ore
Usi
ng
- A click sound is made at each step.- When the maximum position is reached at each side,the tone of the click changes. Thereafter, the set valuedoes not change.
ATL positionSteering D/R rate
Mechanical ATL Adjustment
DT3DT4
Mechanical ATLadjusting screw
Adjustment
Using a Phillips screwdriver, adjust the triggerbrake (reverse) side stroke by turning thescrew through the adjusting hole indicated bythe arrow in the figure. (The screw moves thethrottle trigger stopper.)
- When the adjusting screw is turned clockwise, thestroke becomes narrower.
Make this adjustment when you want to make the throttle trigger brake (reverse) sidestroke narrower.
CautionWhen the stroke is adjusted, the throttle servo travel must be adjusted by data setting.
Wheel Tension Adjustment
Make this adjustment when you want to change the steering wheel spring tension.
Adjustment
Turn the screw inside the adjustinghole using a Phillips screwdriver.
CautionIf turned too far counterclockwise, the adjustingscrew may fall out.
Tension adjusting screw
- Turning the adjusting screwclockwise increases the springtension.
18
Befo
re Using
For dry cell battery systemLoad the eight batteries in accordance with the polarity markings on the batteryholder. (8 AA Size Batteries)
Battery Replacement
(Battery Replacement Method)
1. Remove the battery cover fromthe transmitter by sliding it in thedirection of the arrow in the figure.
2. Remove the used batteries.
3. Load the new AA size batteries .Pay very close attention to thepolarity markings and reinsertaccordingly.
4. Slide the battery cover backonto the case. Check:
Turn the power switch on the trans-mitter to the ON position. Check thebattery voltage display on the LCDscreen.If the voltage is low, check the batter-ies for insufficient contact in the caseor incorrect battery polarity.
CautionAlways be sure you reinsert the bat-teries in the correct polarity order.
If the batteries are loaded incorrectly, thetransmitter may be damaged.
When the transmitter will not beused for any period of time, alwaysremove the batteries.
If the batteries do happen to leak, clean thebattery case and contacts thoroughly. Makesure the contacts are free of corrosion.
Low Battery Alarm:If the transmitter battery voltagedrops below 8.5V an alarm will soundand "LOW BT" will be displayed onthe LCD screen.
The low battery alarm is meant to be asafety feature only. Do NOT operateyour radio below 9V. Always shutyour radio off as soon as possible af-ter the low battery warning tone toavoid loss of control.
19
Bef
ore
Usi
ng
For NiCd battery systemThe NiCd battery is connected by a connector so it can be easily removed when thetransmitter is not being used for an extended amount of time.
- Always use an NT8F700B NiCd battery.
NiCd batteryNT8F700B
Charging the NiCd Battery
Charging
1. Plug the transmitter cord of the spe-cial charger into the charging jackon the side of the transmitter.
2. Plug the charger into an AC outlet.
3. Check that the charging LED lights.
Charger
Transmitter chargingLED
Cord to transmittercharging jack
When charging the NT8F700B NiCd battery with the special charger, allow about 15hours for charging. If the transmitter has not been used for some time, cycle thebattery by charging and discharging it two or three times.
Over current protectionThe transmitter charging circuit is equipped with an over current protection circuit. Ifthe battery is charged with a quick charger for other than digital proportional R/Csets, it may not be fully charged.
AC outlet
Charging jack
20
Befo
re Using
Always use the special charger or a quick charger for digital pro-portional R/C sets to charge a digital proportional R/C set NiCdbattery.
Overcharging a NiCd battery can result in burns, fire, injuries, or loss of sight due tooverheating, breakage, or electrolyte leakage.
Never try to recharge a dry cell bat-tery.
The transmitter may be damaged or the batteryelectrolyte may leak or the battery may break.
When the charger is not in use, dis-connect it from the AC outlet.
Do this to prevent accidents and to avoid overheat-ing.
Caution
Never plug it into an outlet of otherthan indicated voltage.
Plugging the charger into the wrong outlet may re-sult in an explosion, sparking, or fire.
Do not insert and remove thecharger when your hands are wet.
It may cause an electric shock.
Warning
Use thespecialcharger.
Set data backupThe set data of each function of the T3PM-2.4G transmitter is stored in a memoryelement that does not require a backup battery. Therefore, the transmitter can be usedwithout paying attention to the backup battery life.
21
Bef
ore
Usi
ng
ReceiverNomenclature
For the receiver, servos, and other connections, see page 22.
Connectors3: CH3 servo (CH3)2: Throttle servo (CH2)1: Steering servo (CH1)B/C: Power connector/DSC connectorRS232C: (for factory use only)
R603FFreceiver
Antenna Coaxial cable
22
Installatio
n
Warning
Installation
Receiver and Servo Connections
Installation For Electric Powered Models
When connecting and installing the receiver and servos, read the “Installation SafetyPrecautions”.
Installation For Gas Powered Models
R603FF
ESC
R603FF
Installation Safety Precautions
Antennatube
Antenna
Coaxialcable
R603FF
Receiver Antenna Installation
Install the R603FF receiver on the car as follows:
Note: The operating range may become shorter, depending onwhere the receiver and the antenna are mounted.
•Install the antenna in the higher place as shown in the figure.•Keep the antenna as for away from the motor, ESC and othernoise sources as possible.
•Put the antenna in the antenna tube to protect it.
•Do not cut the antenna.•Do not bend the coaxial cable. Doing so causes damage.
23
Inst
alla
tio
n
WarningConnector Connections
Be sure the receiver, servo and con-nectors are fully and firmly con-nected.
If vibration from the model causes a connector to workloose while the model is in operation, you may losecontrol .
Electronic speed controlInstall the heat sinks where they willnot come in contact with aluminum,carbon fiber or other parts that con-duct electricity.
If the Electronic speed control heat sinks touch othermaterials that conduct electricity a short circuit couldoccur. This could result in loss of control and damageto the system.
Receiver Vibration Damping andWaterproofing
(Car)Dampen the vibration to the receiverby mounting it to the chassis ormounting plate with thick, double-sided tape in electric powered mod-els. In gas powered models, wrap thereceiver in foam and mount it wherethe vibration is the least prevalent. (Boat)Dampen the vibration to the receiverby wrapping it in foam. Waterproof byplacing it in a plastic bag or make theradio box in your model watertight.
If the receiver is subjected to strong vibration or shockerratic or loss of control may occur. If any moisturecomes in contact the receiver and servos you mayexperience the same result as well as damage to thesystem.
Servo ThrowOperate each servo over its full strokeand be sure the linkage does not bindor is loose.
The continuous application of unreasonable force to aservo may cause damage and excessive batterydrain.
Servo InstallationWhen you install the servos alwaysuse the rubber grommets provided inservo hardware bags. Mount the ser-vos so they do not directly come incontact with the mount.
If the servo case comes in direct contact with themount, vibration will be directly transmitted to theservo.
If this condition continues for a long time the servomay be damaged and control will be lost.
Motor Noise SuppressionAlways install capacitors to suppressnoise when electric motors are used.
If capacitors are not properly installed you could expe-rience erratic operation and reduced range as well asloss of control.
Other Noise Suppression MethodsBe sure there are no metal parts inyour model which under vibrationcould come in contact with othermetal parts.
Metal to metal contacts under vibration will emit a highfrequency noise that will affect the receiver's perfor-mance. You could experience erratic operation andreduced range as well as loss of control.
24
Initial S
et-Up
Initial Set-Up
How to link the transmitter and the receiverEach transmitter has an individually assigned, unique ID code. In order to start opera-tion, the receiver must be linked with the ID code of the transmitter with which it isbeing paired. Once the link is made, the ID code is stored in the receiver and nofurther linking is necessary unless the receiver needs to be used with an other trans-mitter. (For T/R set, the link is already done at factory.)
Link procedure
1. Bring the transmitter and the receiver close to each other, within one meter.
2. Turn on the transmitter.
3. Check the LED that is placed on the back side of thetransmitter to see if the RF signal is transmitted. Whenthe green LED is solid ON, the RF signal is transmitted.*Please refer the table below for LED status vs transmitter's condition.
LED status vs transmitter's condition:Parameter check for 0.5 seconds after power-on Red: OnTransmitting signals Green: OnF/S is activated by the F/S switch of the transmitter. (PPM mode) Green: BlinkUnrecoverable failure (EEPROM, etc.) Red and Green turn on alternatively.
4. Turn on the receiver.
5. Push the tactile switch of the receiver.
6. When the link is complete, the LED in the receiver changes to solid green.*Please refer the table below for LED status vs receiver's condition.
LED status vs receiver's condition:No signal reception Red : OnReceiving signals Green: OnReceiving signals, but ID is unmatched. Green: BlinkUnrecoverable failure (EEPROM, etc.) Red and Green turn on alternatively.
How to Set the F/S Position (PPM mode)PPM mode only:
*HRS mode: Set the F/S function by the fail safe function menu.
1. Move and hold the throttle trigger to the F/S servoposition you want to set (slow side). Then push theF/S switch on the transmitter.*The LED blinks green.
Note: Always set the F/S position when turning on the transmitter power.
LED andF/S switch
LED andF/S switch
25
Init
ial S
et-U
p
Preparations (Transmitter)Before setting the transmitter functions, check and set items below.
Model number
Turn on the transmitter power.
Model name
(displayed for about one second)
1. Model Number Check
When the power switch is turned on, the current selected model number is displayed.Check if this number is the model number you want to set-up. To change the modelnumber, use the Model Select function (page 48).
Modulation modePP: PPM mode
HRS: HRS mode
Battery voltage
(Display when power switch is turned on)
2. Modulation Mode Check
The T3PM-2.4G transmitter output signal format can be changed. (HRS/PPM)Check if the modulation mode is set to the desired mode.If this setting is incorrect, change it with the HRS/PPM Select function (page 53).
26
Initial S
et-Up
- Steering dual rate (DT3) checkAt initial set-up, steering dual rate is assigned to grip lever DT3 (upper) at the grip ofthe transmitter. Operate the DT3 lever and check if the D/R value displayed on thescreen changes. After checking D/R, set the steering dual rate to 100%.
- Throttle ATL (DT4) checkAt initial setting, throttle ATL is assigned to grip lever DT4 (lower) at the grip of thetransmitter. Operate the DT4 lever and check if the ATL value displayed on thescreen changes. After checking ATL, set throttle ATL to 100%.
Steering D/Rvalue
Throttle ATLposition
DT3DT4
- Steering trim (DT1) checkAt initial set-up, steering trim is assigned to digital trim DT1 above the steeringwheel. Operate the DT1 lever and check if the steering trim value on the screenchanges. After checking the trim, set the trim value to the center (0) position.
- Throttle trim (DT2) checkAt initial set-up, throttle trim is assigned to digital trim DT2 at the left side of thesteering wheel. Operate the DT2 lever and check if the throttle trim value on thescreen changes. After checking the trim, set the trim value to the center (0) position.
Throttle trimposition
DT2
DT1
Steering trimposition
3. Trims Initial Set-Up
27
Init
ial S
et-U
p
(Set-Up Procedure When Installed In a Car)When installing the servos in a car, performing function set-up in the following orderis recommended.
1. Set up the servo trims (page 23).
2. Set the servo direction of operation using the Reversefunction. (Page 47)The servo installation method and linkage direction dependon the kit. Therefore, the servo operation direction may haveto be reversed relative to transmitter operation. Before in-stalling the servo, check the operating direction and set it us-ing the Reverse function.
3. Set the subtrim and adjust the servo neutral point. (Page46)
4. Set the trigger travel by adjusting the throttle trigger me-chanical ATL to your liking. (Page 17)
5. Set EPA of each channel and adjust the servo throw(travel). (Page 30)
28
Fu
nctio
n M
ap
Function Map
Power switch turned on
The current modulation mode andmodel number are displayed for about two seconds.
Press "SEL" key to selectthe desired function screen.Press it for one second ormore to scroll to the oppositedirection.
Press "CH" key to selectthe next set-up screen.
(Initial Screen)
Digital trim DT1 - DT4 displayThe current position is displayed on the LCD screen for about two seconds when each digital trim is operated.
End Point Adjuster Timer
Model Select
Channel Reverse
Subtrim
Channel 3 Position
ATL Function
Steering D/R
Trim
Steering Speed
Steering EXP/Throttle EXP
ABS Function
Throttle Acceleration
Brake mixing
Programmable Mixing
Fail Safe Function (HRS system only)
29
Fu
nct
ion
Map
System Functions
(displayed for about one second)
Turn on the power switch while pressing "SEL" key.
LED Mode Selection
Condition 2 Selection
Model Copy
Function Select Lever
Model Reset
Function Select Switch
HRS/PPM Select
Model Name
Press "SEL" key to selectthe desired function screen.Press it for one second ormore to scroll to the oppositedirection.
Press "CH" key to selectthe next set-up screen.
30
Fu
nctio
ns
Functions
End point adjuster/EPAUse this when performing left and right steering angle adjustments, throttle high side/brake side operation amount adjustment, and channel 3 servo up side/down side op-eration amount adjustment during linkage.
- Corrects the maximum steering angle and left and right steering angles when thereis a difference in the turning radius due to the characteristics, etc. of the vehicle.
Maximum steering angleThe EPA function basically determines the maximum steering angle of each channel.The functions shown below may have been adjusted, or the operating range set byEPA function may be exceeded. Check the linkage each time the following functionsare adjusted.- Sub trim (all channels)- Throttle Acceleration (Brake side)- Brake mixing rate- Program mixing slave side (all channels)
ATL trimATL trim allows adjustment of the brake side operation amount during operation.Therefore, when the operating angle is adjusted with throttle EPA, ATL trim mustalso be taken into account.
WarningMake sure that the knuckle stopper is not contactedduring steering operation and that unreasonableforce is not applied to the servo during other channeloperation.
If unreasonable force is applied to the servo horn at the knuckle stopperduring steering operation, the servo may malfunction and the model mayrun out of control.
Decide the EPA valueat the contact point.
Caution!
Be sure th
at the st
eering
servo
does not b
ind.
31
Fu
nct
ion
s
Steering (EPA) adjustment(Preparation)- Before setting up the steering wheel EPA, set the steering D/R lever (initial setup:DT3) to the maximum steering angle position 100%.- Select setup item "ST" and make the following adjustments:
1 Steering (left side) adjustment
Turn the steering wheel fully to the left and use the (+) and (-) buttons toadjust the steering angle.
2 Steering (right side) adjustment
Turn the steering wheel fully to the right and use the (+) and (-) buttons toadjust the steering angle.
3 When adjusting the EPA of another channel immediately after this, see theadjustment method for that channel. When ending adjustment, return tothe initial screen by pressing the (SEL) button.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
Adjustment range0~120% (each channel, each direc-tion)Adjustment buttons- Use the (+) and (-) keys to make ad-justments.- Return to the initial value by pressingthe (+) and (-) buttons simultaneously(approx. 1 sec).
Setup itemsST-L.F.U : Steering (left side)ST-R.B.D : Steering (right side)TH-L.F.U : Throttle (forward side)TH-R.B.D : Throttle (brake side)3C-L.F.U : 3rd channel (up side)3C-R.B.D : 3rd channel (down side)
(Setup screen)
Press "CH" key to select the next set-up screen.
Throttle (EPA) adjustment(Preparation)- Before setting the throttle EPA, set the throttle ATL lever (initial setup: DT4) to themaximum steering angle position 100%.- Select setup item "TH" and make the following adjustments:
1 Throttle (forward side) adjustment
Pull the throttle trigger fully to the high side and use the (+) and (-) buttons to adjustthe steering angle. However, when using an FET amp, set to 100%.
32
Fu
nctio
ns
3rd channel servo (EPA) adjustment(Preparation)- Select setup item "3C-L.F.U" and make the following adjustments:(3rd channnel initial setup: SW2)
1 3rd channel servo (up side) adjustment
Use the (+) and (-) buttons to adjust the steering angle.
2 3rd channel servo (down side) adjustment
Select setup item "3C-R.B.D" and use the (+) and (-) buttons to adjust thesteering angle.
3 When adjusting the EPA of another channel immediately after this, see theadjustment method for that channel. When ending adjustment, return tothe initial screen by pressing the (SEL) button.
2 Throttle (brake side/reverse side) adjustment
Push the throttle trigger fully to the brake side and use the (+) and (-) but-tons to adjust the steering angle. However, when using an FET amp, set to100%.
3 When adjusting the EPA of another channel immediately after this, see theadjustment method for that channel. When ending adjustment, return tothe initial screen by pressing the (SEL) button.
33
Fu
nct
ion
sSetup itemSPD-TN: TURN directionSPD-RN: RETURN direction
Adjustment range0~100% (each direction)Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Return to the initial value by pressingthe (+) and (-) buttons simultaneously(approx. 1 sec).
Steering Speed (SPD) adjustment(Preparation)- Select setup item "SPD-TN" and make the followingadjustments:
1 "TN" direction adjustment
Use the (+) and (-) buttons to adjust the delayamount.
2 "RN" direction adjustment
Select setup item "SPD-RN" and use the (+)and (-) buttons to adjust the delay amount.
3 When ending adjustment, return to the initialscreen by pressing the (SEL) button.
100% 1%
サーボの動作が遅くなる。
Setting range: 1~100%At 100%, there is no delay.At 1%, the delay is approximately 1.5seconds.
Servo operation is delayed.
操作時のスピード可変範囲
時間
(約1.5~0.1秒)
戻りのスピード可変範囲 (約1.5~0.1秒)
スティック操作
"TURN"方向
"RETN"方向
Steering Speed/SPDQuick steering operation will cause momentary understeering, loss of speed, or spin-ning. This function is effective in such cases.
Understeering
SpinSmooth cornering
Steering speed not set Steering speed setOperation- This function limits the maximum speed ofthe steering servo. (Delay function)- The steering speed when the steering wheelis operated (TN direction) and returned (RNdirection) can be independently set.
TN directionTurning speed adjustment range
Stick operation
RN directionReturn speed adjust-ment range- If the steering wheel is turned
slower than the set speed, the steer-ing servo is not affected. Time
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
34
Fu
nctio
ns
Steering EXP, Throttle EXP / EXPThis function is used to change the sensitivity of the steering servo around the neutralposition and makes throttle trigger high side and brake side direction servo operationquicker or milder. It has no effect on the maximum servo travel.
Racers TipWhen the setting is not determined, or the characteristics of the model are unknown,start with 0%. (When EXP is set to 0%, servo movement is linear.)
Advice (Throttle EXP)When the course conditions are good and there is no sense of torque at the power unit,set each curve to the + side (quick side). When the road surface is slippery and thedrive wheels do not grip it, set each curve to the - minus (mild) side.
Steering EXP adjustment(Preparation)- Select setup item "EXP-ST" and make the following adjustments:
1 When you want to quicken steering operation, use the (+) button to adjustthe + side. When you want to make steering operation milder, use the (-)button to adjust the - side.
2 When adjusting the EXP rates of another channel immediately after this,see the adjustment method for that channel. When ending adjustment,return to the initial screen by pressing the (SEL) button.
Setup itemEXP-ST: Steering EXP rateEXP-FW : Forward side EXP rateEXP-BK : Brake side EXP rate
Adjustment range-100~0~+100%Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Return to the initial value by pressingthe (+) and (-) buttons simultaneously(approx. 1 sec).
サーボ動作量
ステアリング スティック 動作量
0%(ノーマル) +1%~+100% (クイック)
サーボ動作量
ステアリング スティック 動作量
0%(ノーマル) -1%~ -100% (マイルド)
(Quick) (Mild)Servo travel Servo travel
0% (normal)
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
+1% ~ +100% (quick) 0% (normal) -1% ~ -100% (mild)
Steering wheel travel Steering wheel travel
35
Fu
nct
ion
s
Throttle EXP Adjustment(Preparation)- Select setup item "EXP-FW" and make the following adjustments:
1 Forward side adjustment
Use the (+) button to adjust the + side when you want to quicken the riseand use the (-) button to adjust the - side when you want to make the risemilder.
2 Brake side adjustment
Select setup item "EXP-BK" and use the (+) button to adjust the + sidewhen you want to quicken the rise and use the (-) button to adjust the - sidewhen you want to make the rise milder.
3 When adjusting the EXP rates of another channel immediately after this,see the adjustment method for that channel. When ending adjustment,return to the initial screen by pressing the (SEL) button.
36
Fu
nctio
ns
Setup itemsABS-PT : Brake return amountABS-CY : Cycle speedABS-DL : Delay amountABS-MD : Function ON/Off
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Return to the initial value by pressingthe (+) and (-) buttons simultaneously(approx. 1 sec).
Brake return amount:0 ~ 50 ~ 100Initial value; 50Cycle speed:1~ 30Initial value; 10Delay amount:0 ~ 100Initial value; 0
A.B.S. FunctionWhen the brakes are applied while cornering with a 4 WheelDrive or other type of vehicle, understeer may occur. Thegeneration of understeer can be eliminated and corners canbe smoothly cleared by using this function.
Operation- When the brakes are applied, the throttle servo will pulseintermittently. This will have the same effect as pumpingthe brakes in a full size car.- The brake return amount, pumping cycle, and delayamount can be adjusted.
Without A.B.S.With A.B.S.
Operation DisplayWhen the A.B.S. function is activated, the LED flashes.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
37
Fu
nct
ion
s
0% 100%
A.B.S function adjustment(Preparation)- Select setup item "ABS-MD" and make the following adjustments:
1 (Function ON/OFF)
Set the function to the active state by pressing the (+) or (-) button.OFF : Function OFFON : Function ON
2 (Brake return amount adjustment)
Select setup item "ABS-PT" and use the (+) and (-) buttons to adjust thereturn amount.
"0" : No return"50" : Return to the 50% position of the brake operation amount"100" : Return to the neutral position.
3 (Cycle speed adjustment)
Select setup item "ABS-CY" and use the (+) and (-) buttons to adjust thespeed.
- The lower the set value, the faster the cycle speed.
4 (Delay amount setup)
Select setup item "ABS-DL" and use the (+) and (-) buttons to adjust thedelay amount.
"0" : A.B.S. function performed without any delay"50" : A.B.S function performed after an approximate 0.7 sec delay."100" : A.B.S. function performed after an approximate 1.4 secs delay.
5 When ending adjustment, return to the initial screen by pressing the (SEL)button.
38
Fu
nctio
ns
Forward acceleration amount0~100Initial value: 0Brake side acceleration amount0~100Initial value: 0
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return to theinitial screen.
Carburetor
Servo horn
Brake side
A slight clearance is required at the linkage, but thethrottle acceleration function acts to reduce the timelag caused by this clearance.
Throttle Acceleration / ACCGasoline engine cars have a small time lag at both the forward side and brake sidebecause a certain clearance is necessary at the linkage. Reducing this time lag at thetransmitter side provides the same sharp response as electric motor cars.
Operation- Operation near the throttle trigger neutral positionbecomes a sharp rise.- The forward and brake sides can be set separately.
Set valueThe standard value (100% point) of this setup effects the operation amount set bythrottle EPA function.
Setup itemsACC-FW : Forward side accelerationamountACC-BK : Brake side accelerationamount
BRAKE
FORWARD
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
39
Fu
nct
ion
s
Throttle acceleration adjustment(Preparation)- Select setup item "ACC-FW" and make the following adjustments.
1 (Forward acceleration amount adjustment)
Use the (+) and (-) buttons to adjust the acceleration amount."0": No acceleration"100": Maximum acceleration (Approximately 1/2 of the forward side steering angle)
2 (Brake side acceleration amount adjustment)
Select setup item "ACC-BK" and use the (+) and (-) buttons to adjust theacceleration amount.
"0": No acceleration"100": Maximum acceleration (Brake side maximum steering angle)
3 When ending adjustment, return to the initial screen by pressing the (SEL)button.
40
Fu
nctio
ns
Brake mixing adjustment(Preparation)- Select setup item "BMXMD" and make the following adjustments.
1 (Function ON/OFF)
Set the function to the "ON" state by pressing the (+) or (-) button.OFF: Function OFFON: Function ON
2 (Mixing amount adjustment)
Select setup item "BMX-RT" and use the (+) and (-) buttons to adjust themixing amount.
- Mixing amount can be adjusted within the 0~120% range.
3 When ending adjustment, return to the initial screen by pressing the (SEL)button.
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return to theinitial screen.
Mixing rate0 ~ 100 ~ 120Initial value: 100
Brake Mixing / BMXUse this mixing when the front and rear brakes must be adjusted independently, suchas in 1/5GP cars, etc. This mixing uses the 2nd channel to control the rear brakes andthe 3rd channel to control the front brakes.
Operation- When braking, mixing is applied to 2nd channel and to 3rd channel.- Mixing rate setting are possible.- The set value of A.B.S. functions is reflected.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
Setup itemsBMX-RT: Mixing rateBMX-MD: Function ON/OFF
41
Fu
nct
ion
s
Programmable Mixing / PMXThis function allows you to apply mixing between the steering, throttle, and channel3 channels.
Program mixing adjustment(Preparation)- Use the function select switch function (page 54) to select the switch (as desired.)- Select setup item "PMX-MD" and make the following adjustments.
1 (Function ON/OFF)
Set the function to the "ON" state by pressing the (+) or (-) button."INH": Function OFF, "ON": Function ON, "OFF": Switch OFF
2 (Master channel)
Select setup item "PMX-MS" and select the master channel by pressingthe (+) or (-) button.
3 (Slave channel)
Select setup item "PMX-SL" and select the slave channel by pressing the(+) or (-) button.
4 (Mixing amount adjustment)---upper item
Select setup item "PMX-RT(L.F.U)" and use the (+) and (-) buttons to ad-just the mixing amount.
5 (Mixing amount adjustment)---lower item
Select setup item "PMX-RT(R.B.D)" and use the (+) and (-) buttons to ad-just the mixing amount.
6 When ending adjustment, return to the initial screen by pressing the (SEL)button.
Setup itemsPMX-RT(L.F.U): Mixing rate (Leftside)PMX-RT(R.B.D.): Mixing rate (Rightside)PMX-MS: Master channelPMX-SL: Slave channelPMX-MD: Function ON/OFF
Mixing amount-100~+50~+100Initial value: +50Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return to theinitial screen.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
42
Fu
nctio
ns
Fail Safe Function/FAIL SAFE (HRS mode)(This function can only be used with HRS system receivers.)Fail safe functionThis function moves the steering, throttle and channel 3 servos to a preset positionwhen the receiver cannot receive the signal from the transmitter for some reason.When the servo operation position is not set, this function operates so that the servosremain in the position they were in immediately before reception was lost. When thesignal from the transmitter can be received again, this function automatically resets.
- For gasoline engine cars, it is recommended that the throttle channel be set to thedirection that applies the brakes.
Battery fail safe functionWhen the receiver battery voltage drops to a certain voltage or less, this functionmoves the throttle servo to the position set by fail safe function. When the voltagerecovers, this function automatically resets.
Setup itemsF/S-ST: Steering settingF/S-TH: Throttle settingF/S-3C: Channel 3 setting
Fail safe function setup(Preparation)- Select the desired channel setup item and make the following adjustments.
1 (Servo position setup)
When the fail safe function operates, the steering wheel, the throttle triggeror channel 3 lever remains in the desired operation position. When the (+)and (-) buttons are pressed simultaneously for about 1 second, the servoposition is displayed and you can confirm that the function was set.
When you want to release the setting, press the (+) or (-) button. "OFF" isdisplayed.
(Each channel can be set similarly.)
2 When ending adjustment, return to the initial screen by pressing the (SEL).
The servo position isdisplayed when thefail safe functionwas set up.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
43
Fu
nct
ion
s
Steering Trim, Throttle Trim / TRMSteering neutral adjustments and throttle neutral adjustments during a run can be made bymoving the trim lever to the left or right (the up or down). This setting is linked totransmitter digital trim lever DT1 and DT2. When DT1 or DT2 is assigned to anotherfunction, set the trim function with this screen.
When Trim usage is extremeIf it takes most of your trim movement to get a servo to the neutral position, repositionthe servo horn or servo saver on the servo and inspect your linkage installation.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
When each digital trim is operated, the" T R M " s c r e e n i s d i s p l a y e dautomaticaly for about three seconds.
Steering trimposition
Throttle trimposition
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return tothe initial screen.
Trim positionL.F.U 100% ~ 0 ~ R.B.D 100%Initial value: 0%
Setup ItemTRM-ST: Steering trim posiionTRM-TH: Throttle trim posiion
Trim adjustment(Preparation)- Select the desired setup item and make the following adjustments.
1 (Position adjustment)
Use the (+) and (-) buttons to adjust the trim position.- This position is linked with the digital trim (DT1 or DT2).
2 When ending adjustment, return to the initial screen by pressing the (SEL)button.
44
Fu
nctio
ns
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
When Dual Rate lever is operated, the"D/R-ST" screen is d isp layedautomaticaly for about three seconds.
Dual Rate value
D/R value0 ~ 100%Initial value: 100%
Setup ItemD/R: Steering D/R value
Steering D/R adjustment
1 (D/R value adjustment)
Use the (+) and (-) buttons to adjust the D/R value.- This position is linked with the grip lever (DT3).
2 When ending adjustment, return to the initial screen by pressing the (SEL)button.
Steering Dual Rate / D/R-STWhen the steering angle is too small at under steering at corners while running, in-crease the rate. When the steering angle is too large at over steering, decrease the rate.The setup here is linked with transmitter grip lever DT3. Adjustments can be made atthis screen even if DT3 is assigned to another function.
Operation- The steering servo left and right steering angles are adjusted simultaneously.
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return to theinitial screen.
Throttle ATL Function / ATL-BKThis function adjusts the - side when the braking effect is strong and the + side whenthe braking effect is weak. This setting is linked to transmitter grip lever DT4. WhenDT4 is assigned to another function, set the ATL function with this screen.
OperationThe throttle brake side (when the throttle trigger is pushedforward) brake amount can be adjusted.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
When ATL lever is operated, the "ATL-BK" screen is displayed automaticalyfor about three seconds.
ATL position
45
Fu
nct
ion
s
Channel 3 Position / CH3Use this function to set the servo position of the channel 3.This setting is linked to transmitter switch (SW2). When the switch is assigned toanother function, set the channel 3 position with this screen.
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return tothe initial screen.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)When channel 3 switch is operated,the "CH3" screen is displayedautomaticaly for about three seconds.
Channel 3position
Channel 3 positionL.F.U 100% ~ 0 ~ R.B.D 100%Initial value: 0%Setup Item
RATE: Channel 3 posiion
Channel 3 adjustment(Preparation)- Select setup item "CH3" and make the following ad-justments.
1 (Position adjustment)
Use the (+) and (-) buttons to adjust the channel3 position.
- This position is linked with the switch (SW2).
2 When ending adjustment, return to the initialscreen by pressing the (SEL) button.
ATL position0 ~ 100%Initial value: 100%
Setup ItemATL-BK: Throttle ATL position
Throttle ATL adjustment
1 (ATL position adjustment)
Use the (+) and (-) buttons to adjust the ATL position.- This position is linked with the grip lever (DT4).
2 When ending adjustment, return to the initial screen by pressing the (SEL)button.
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return to theinitial screen.
46
Fu
nctio
ns
センターを出すため に使用する
Subtrim / SBTUse this function to adjust the neutral position of the steer-ing, throttle and channel 3 servos.Subtrim shifts the entire servo travel range in the set direc-tion.
Use to adjust the neutral position
Subtrim adjustment(Preparation)-Set the steering and throttle digital trims to the neutral "0" position. Set CH3 to thecenter "0" position.- Preselect setup channel "ST", "TH", or "3C".
1 (Subtrim adjustment)
Use the (+) or (-) button to adjust the center.
(Each channel can be set similarly.)
2 When ending adjustment, return to the initial screen by pressing the (SEL)button.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
Setup ItemSBT-ST : SteeringSBT-TH : ThrottleSBT-3C : Channel 3
Subtrim positionL.F.U 100% ~ 0 ~ R.B.D 100%Initial value: 0%
Adjustment buttons- Use the (+) and (-) buttons to makeadjustments.- Press the (+) and (-) buttons simulta-neously (approx. 1 sec) to return tothe initial screen.
47
Fu
nct
ion
s
Servo Reverse / REVThis function reverses the direction of operation of the servos related to transmittersteering, throttle, and channel 3 operation.
However, when the position set by trim or subtrim shifts from the center, the centerbecomes the opposite side.
Servo Reverse Function Setting(Preparation)- Preselect setup channel "ST", "TH", or "3C".
1 (Servo reverse setting)
Use the (+) or (-) button to reverse the servo operation direction.
(Each channel can be set similarly.)
2 When ending adjustment, return to the initial screen by pressing the (SEL)button.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
Setup ItemREV-ST : SteeringREV-TH : ThrottleREV-3C : Channel 3
Servo directionOFF: Normal sideON: Reverse side
48
Fu
nctio
ns
Model Select / SELUse this function to call a new model number, or to change a set model number, to set newmodel data.The T3PM-2.4G transmitter can store the model data for ten R/C cars.
Calling model memories of different modulation modes (HRS, PPM)
After the new model is called, signals are still output in the old model modulationmode until the transmitter power is turned off. Before using the new modulationmode, turn the power off and on. (See page 53 for the HRS/PPM mode selection.)
Model Select
1 (Model No. selection)
Use the (CH) button to select the Model No.
2 (Select execution)
Press the (+) and (-) buttons simultaneously for about 1 second.
3 When ending adjustment, return to the initial screen by pressing the (SEL)button.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
Model name
Model number:01 ~ 10
49
Fu
nct
ion
s
Timer / TIMERUse the timer by selecting from UP Timer or DOWN timer.
UP TIMER function- The UP TIMER can be used to count the time between start and stop.- The timer repeatedly starts and stops each time the switch is operated andaccumulates the time between each start and stop.- The first start operation can be linked to the throttle trigger.- An alarm sound can be set.
DOWN TIMER function- The DOWN TIMER can be used to count the time between start and stop. (Thetime remaining is displayed.)- Start and stop are repeated at each switch operation and the time between each startand stop is counted down and displayed. The start time becomes the alarm set time.(When the count reaches 00 minute 00 second, the down timer operates like an uptimer.)- The first start operation can linked with the throttle trigger.- An alarm sound can be set.
(Initial screen)
Press "SEL" key to select thedesired function screen.
Calling the setup screen
(Setup screen)
Press "CH" key to select the next set-up screen.
Setup itemsTYP: Timer selectionALM-TM: Alarm time setup
Timer setup(Preparation)- Use the function select switch function (page 54) to select the switch.(SW1: Select the "TM" in the above function.)
1 (Timer selection)
Select setup item "TYP" and use the (+) and (-) buttons to select the timertype.
2 (Alarm time setup)
Select setup item "ALM-TM" and use the (+) and (-) buttons to set thealarm time.
Timer typeTYP-UP: UP timerTYP-DN: DOWN timerAlarm time1 ~ 100 min.Initial value: 4 min.
50
Fu
nctio
ns
Checking the lap times
1 Select the lap time screen "ALL" and check the total time.
2 Use the (+) and (-) buttons to scroll each lap screen and check each laptime.
3 (Linking start with the trigger)
Select setup item "TIMER" and press the (+) and (-) buttons simulta-neously for about 1 second. A beeping sound is generated and "RDY"displays at the timer display and the system enters the RDY state. Triggeroperation starts the timer.
(Timer start/stop operation)The switch SW1 preset by function select switch function (page 54) starts the timer.Only starting can be linked with the throttle trigger.
(LAP memory operation)This timer can memorize each lap time of each switch (SW1) operation. (100 laps)Switch operation after the set time by alarm has elapsed automatically stops thetimer. Each lap time is memorized in a lap memory. The lap times are written sequen-tially. When the timer is stopped, the final lap is memorized and the total time isautomatically written. The lap times are memorized to a next start and can be checkedat the lap time screen.
51
Fu
nct
ion
s
Model Copy
1 (Copy destination selection)
Use the (CH) button to select the copy destination model No.
2 (Copy execution)
Press the (+) and (-) buttons simultaneously for about 1 second.
3 When ending adjustment, turn off the power switch before use.
Model Copy / CPYThis function copies the entire contents of the currently called model memory toanother model memory.
Current model No. Copy destination model No.
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
52
Fu
nctio
ns
Model Reset / CLRThis functions resets the contents of the currently called model memory to the initialvalue. However, it does not reset the lap time memory, HRS/PPM select, and LEDmode selection.
Model Reset
1 (Reset execution)
Press the (+) and (-) buttons simultaneously for about 1 second.
2 When ending adjustment, turn off the power switch once before use.
Current model No.
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
Model Name / NAMThis function allows you to assign a three character name to each model memory.(Number and alphabet can be used.)
Model Name
1 Move the cursor (blinking) to the column you want to change using the(CH) button.
2 Change the character using the (+) or (-) button.
(Set the model name by repeating steps 1 and 2 above. )
3 When ending adjustment, turn off the power switch before use.
Model name
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
53
Fu
nct
ion
s
HRS/PPM mode selection
1 (Mode selection)
Use the (+) or (-) button to select the mode.
2 When ending adjustment, turn off the power switch before use.
HRS/PPM Select / MODThe signal mode output from the transmitter can be changed. (PPM/HRS)
- When the mode was changed and when a model of a different mode wasselected, signals are output in the mode set at the point at which thetransmitter power was turned back on.
Signal modeHR: HRS modePP: PPM mode
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
54
Fu
nctio
ns
SW1
SW2
Function Select Switch / FNC-SWThis function allows selection of the function to be performed by the switches(SW1/SW2).
Settable functions (SW1)OF: (function off)3C: Channel 3MX: Programmable mixingTM: Timer switch
Settable functions (SW2)OF: (function off)3C: Channel 3MX: Programmable mixing
Function select switch setup
1 (Setup item selection)
Use the (CH) button to select the item to be set.
2 (When changing the function)
Use the (+) or (-) button to select the function.
3 When ending adjustment, turn off the power switch before use.
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
Press "CH" key to select the next set-up screen.
55
Fu
nct
ion
s
Initially set functionsDT1: Steering trimDT2: Throttle trimDT3: Dual rate functionDT4: ATL function
DT1
DT2
Function Select Lever / FNC-DTThis function allows selection of the function performed by the grip lever (DT3/DT4)and digital trim (DT1/DT2).
DT3DT4
Settable functionsST: Steering trimTH: Throttle trimDR: Steering D/RAT: Throttle ATLE1: Steering EXPBK: Brake mixing rate3C: Channel 3OF: (function off)
Function select lever setup
1 (Setup item selection)
Use the (CH) button to select the item to be set.
2 (When changing the function)
Use the (+) or (-) button to select the function.
3 When ending adjustment, turn off the power switch before use.
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
Press "CH" key to select the next set-up screen.
56
Fu
nctio
ns
Condition 2 Selection / COND2
Condition 2 selection
1 Use the (+) or (-) buttons to select the on/off state.
2 When ending selection, turn off the power switch before use.
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
Condition 2 SelectionIn specific functions, two rates can be set up, and switched with the switch (SW1)simultaneously during a run.If this function is activated, SW1 is used only for this function, and it becomes impos-sible to use it for other functions automatically.When the switch (SW1) is operated, Condition 2 on/off state changes by turn. Whenthis function is turned on, the beep sounds and the pilot lamp blinks.
Related functions:Steering speedSteering EXPThrottle EXPABS return amountBrake mixing rateProgrammable mixingSteering trimThrottle trimSteering D/RThrottle ATL
LED Mode Selection / LED-MDYou can select your desired brightness of the pilot lamp. (Four steps)
LED mode selection
1 Use the (+) or (-) buttons to select the brightness of the pilot lamp.
2 When ending selection, turn off the power switch once before use.
Calling the setup screen
1. Turn on the power switchwhile pressing "SEL" key.
2. Next, use "SEL" key to selectthe desired function screen.
LED mode(Min.)L-1 ~ L-4(Max.)
57
Ref
eren
ce
Reference
Ratings*Specifications and ratings are subject to change without prior notice.
- Communication method: One-way operation system- Mode: PPM, HRS (Auto-detect)- Maximum operating range: 80m (Optimum condition)- For safety: F/S, B-F/S, ID (About 4 billion ways of pair identifications)
Transmitter T3PM-2.4G:
(Wheel system, 3 channels)- Transmitting frequency: 2.4GHz band- Power requirement: (NiCd battery) NT8F700B(9.6V),
(Dry cell battery) Penlight x 8(12V)- Current drain: 250mA or less- Transmission antenna: 1/2 mono-pole
Receiver R603FF:
- Power requirement: 6V NiCd battery- DSC function available- RS232C port: (for factory use only)- Size: 39x26x14mm (excluding a projection part)- Weight: 14.1g
58
Referen
ce
Optional PartsThe following parts are available as 3PM-2.4G system options. Purchase them tomatch your application. For other optional parts, refer to our catalog.
Transmitter NiCd Battery
When purchasing a transmitter NiCd battery as a spare, etc., use the following:
NT8F700B
(9.6V/700mAh)
Part name
59
Ref
eren
ce
TroubleshootingIf your system fails to operate or you experience a short range problem or erraticcontrol, check the table below for possible causes. If after you have followed thesuggestions listed the problem is not corrected, return the system to our service de-partment for inspection and repair.
(Item Check)
TransmitterBatteryDead battery -> Change the batteries. Charge the NiCdBatteries inserted incorrectly. -> Reload the batteries in accordance with the polarity markingsFaulty contact -> Check to see if the contacts are bent and not making good contactDirty contacts -> Clean the contacts and check for corrosion.
Monitor LEDCheck the LED on the rear of the transmitter.Refer to the "How to bind the transmitter and the receiver", p 24.
ReceiverBatteryDead battery -> Replace or rechargeWrong polarity -> Check connections
AntennaNear other wiring -> Move away from wiringWas antenna cut -> Request repairIs the antenna installed correctly -> Refer to the receiver installation, p 22.
Monitor LEDCheck the LED of the receiver.Refer to the "How to link the transmitter and the receiver", p 24.
Connector connectionsWiring incorrect -> Insert all connectors firmlyLoose connections -> Push the connector in firmly
LinkageBinding or loose -> Adjust the linkage in modelIs movement stiff -> Adjust linkage in model
Motor (Electric powered)Noise problems -> Install capacitors on motor
60
Referen
ce
Error DisplaysLow Battery Alarm
If the transmitter battery voltage drops to 8.5V or less, an audible alarm will soundand "LOW BT" will be displayed on the LCD screen.
LCD screen:
Audible alarm:Continuous tone.
Backup Error
If the data is lost for an unknown reason, an audible alarm will sound and "BCK UP"will be displayed on the LCD screen.
LCD screen:
Audible alarm:Tone will sound (9 times), thenrepeat.
WarningWhen a low battery alarm is gener-ated, cease operation immediatelyand retrieve the model.
If the battery goes dead while in operation, you willlose control.
WarningWhen a backup error is generated,immediately stop using the systemand request repair from the FutabaService Center.
If you continue to use the system, the transmittermay malfunction and cause loss of control.
61
Ref
eren
ce
When requesting repairBefore requesting repair, read this instruction again and recheck your system. Shouldthe problems continue, request as follows.
(Information needed for repair)Describe the problem in as much detail as possible and send the letter along with thesystem in question.- Symptom (Including the conditions and when the problem occurred)- R/C System (Send transmitter, receiver and servos)- Model (Type of model, brand name and model number or kit name)- Detailed packing list (Make a list of all items sent in for repair)- Your name, address and telephone number.(Warranty)
Read the Warranty card.- When requesting warranty service, send the card or some type of dated proof ofpurchase.
Hobby Services (U.S. only)3002 N. Apollo Drive, Suite 1Champaign, IL 61822 U.S.A.Phone: (217) [email protected]
FUTABA CORPORATIONMakuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan
Phone: (043) 296-5119 Facsimile: (043) 296-5124©FUTABA CORPORATION 2007, 2 (1)
Top Related