* 5 1 0 0 0 1 7 0 4 8 - 0 1 *
01 Stand
02 03
Connection procedure
04
01
05
Adjusting the tension
Assembly procedure
■ VH-11 (Hi-hat)
02
Turn back to�x the cables
Leave someslack in thecables
Tighten itnot to slip
Wind thecable tieonce
Compatible Stand
TD-9KX2 parts
1/4” plug (mono)
Stereo 1/4" plug
Amplied speakers, etc.
Stereo headphones
(indicator)
to AC outlet
AC adaptor
Power cord
1. Adjustthegapbetweenthemetalportioninthecenterofthelowerhi-hatandthesensor’scenter tip toaclearanceofapproximately3mm,thentightentheclutchscrew.
3mm
2. Changethespringtensionbyadjustingthehi-hatstand.
* The tension may not be adjustable on some stands.
1. Loosentheclutchscrewand let thehi-hatrestnaturallyonthemotionsensorunit.
2. Pressthe[SETUP]-[F1](TRIG)button.
The“TRIGGERTYPE”screenwillappear.
3. Usethe[CURSOR]buttontomovethecursorto“H”(HI-HAT).
4. Pressthe[F3](ADVNCD)-[F3](HI-HAT)button.
Thefollowingscreenwillappear.
5. Whileyouwatchthemeterthat’sdisplayedintherightsideofthescreen,turntheVH-11’sVHoffsetadjustmentscrewtoadjustit.
Adjustthescrewsothattheblack appearsinthemeter.
T3
T2
CR1
SNR
KIK
TD-9
T1
RD RDB
HH
HHC
Setup Guide
� Kick pad (KD-9) � V-Hi-hat (VH-11) � V-Pad for snare (PD-105)
� V-Pad for tom (PD-85 x 3)
� Percussion sound module (TD-9)
� Connection cable (special for TD-9)
� AC adaptor � Drum key
Assemble the stand Attach the parts
Connect the AC adaptor and speakers
Attach the snare (PD-105) and toms (PD-85)
Attach the hi-hat (VH-11)
Attach the crash cymbal (CY-12C) and ride cymbal (CY-13R)
Attach the sound module (TD-9)
1
3
4
2
5
6Tuning bolt
HoopWasher
Gap
1. Finger-tightenallsixofthetuningboltsinthesequenceshownintheillustration.
2. Theappropriateamountoftensionisonethatwillprovideapproximatelythesamestrikingresponseasonanacousticdrum.
3. Usethedrumkeytoadjustthetensionasneeded.
Rod Rod
Tighten
Loosen
Tighten
Loosen
PD-105
PD-85
PD-85
PD-85
CY-12C CY-13R
KD-9
VH-11
TD-9
Adjusting the offset.
* When performing, make sure that the name “Roland” on the hi-hat is on the opposite side of the stand from the hi-hat pedal.
Detailed explanation of each part
* Use a commercially available hi-hat stand.
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.
Adjusting the hi-hat.
* The parts required for mounting the cymbals and the hi-hat are included in the TD-9KX2 attachment box.
� V-Cymbal for crash (CY-12C)
� V-Cymbal for ride (CY-13R)
Diameter: 6.0–7.0 mm(0.236"–0.276")
Diameter: 11.7 mm (1/2") Max.
CONTROL OUTjack
TRIGGER OUTjack
HHC plug HH plug
Ifyou’reusingtheVH-11V-hi-hat,executetheoffsetadjustmentfromtheTD-9aftermakingconnections.
Thisadjustmentisrequiredinordertocorrectlydetectopen,close,andpedaloperations.
Fixing the cables
VH o�setadjustment
screw
OPEN CLOSE
Iftheclosedhi-hatsoundisdifficulttoattain,rotatetheVHoffsetadjustmentscrewtowards“CLOSE.”Iftheopenhi-hatsoundisdifficulttoattain,rotatethescrewtowards“OPEN.”
* If the sound cuts off when you strike the hi-hat forcefully, rotate the VH Offset adjustment screw towards “OPEN.”
* Although the gap can be adjusted to a clearance that makes playing the hi-hat easier, setting too narrow or wide a gap can cause improper function of the unit and prevent the hi-hat from sounding as you intend. Setting the gap to 3 mm provides the most natural feel when playing the VH-11.
* Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad’s function.
* If the hi-hat clutch has been detached from the hi-hat, refer to “If the Clutch Was Apart from the Hi-Hat” in the owner’s manual.
Insulating plateSponge side up
Hi-hat“Roland” logoon the farther side
Motion sensor unitCONTROL OUT jackon the farther side
Clutch screw
Hi-hat clutch
Check to make sure that the cymbal rod has been tightened su�ciently
Attach the kick pedal (KD-9)
* Use a commercially available hi-hat stand.
* Adjust the position at which the TD-9 is attached so it doesn’t make contact with the VH-11.
Asseenfromthefront
Copyright © 2010 ROLAND CORPORATIONAllrightsreserved.NopartofthispublicationmaybereproducedinanyformwithoutthewrittenpermissionofROLANDCORPORATION.
Beforeusingthisunit,carefullyreadthesectionsentitled:“USINGTHEUNITSAFELY”and“IMPORTANTNOTES.”Thesesectionsprovide important informationconcerningtheproperoperationof theunit.Additionally, inorderto feelassuredthatyouhavegainedagoodgraspofeveryfeatureprovidedbyyournewunit,Owner’smanualshouldbereadinitsentirety.Themanualshouldbesavedandkeptonhandasaconvenientreference.
Roland,V-Drums,V-TOUR,V-CYMBALS,andV-HI-HATareregisteredtrademarksofRolandCorporationintheUnitedStatesand/orothercountries.
Check the included items
� Stand (MDS-9) � Hi-hat mount � Cymbal mount x 2
� Cable tie x 6
� Drum key
� Owner’s Manual
Manual set � Setup Guide (this document) � Quick Start � Owner’s Manual
1. Loosenthehandknobs(A,twolocations)andspreadopentheleftandrightlegsofthestandasshownintheillustration.
3. Adjustthepadmounts(C,fourlocations)asshownintheillustra-tion.
2. Loosenthehandknobofthesnarepipe(B),andpulloutthesnarepipetowardthesideoftheperformer.
4. Attachthecymbalmounts(D,twolocations)asshownintheillustration.
1.2 m
135˚ 135˚
* Do not spread open the stand farther than 135 degrees as shown in the illustration. Nor should you spread the stand wider than 1.2 meters (48 inches).
Tightenthewingnuttoobtainanappropriateamountofsway.
Wing nut
Felt washer
Installthekickpedalsecurely.
Connect the pads to the sound module* Use cable ties to fasten the cables at the circled locations “ ” so that they do
not interfere with your performance. Make sure to wrap the cable ties around the pipes.
* To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, anchor the power cord using the cord hook, as shown in the illustration.
3. ConnecttheACadaptor,andfastenittothecablehookasshownintheillustrationtopreventitfrombeingaccidentallyunplugged.
2. Labelsindicatingthepadtobeconnectedareattachedtothecable.Makeconnectionsasshownintheillustration.
KnobBOW/EDGEOUTPUT jack
BELL OUTPUT jack
RD plug
RDB plug
■ To learn about the TD-9’s wide range of unique functionality, refer to “Quick Start.” ■ If you need further information regarding the set up of TD-9K2, refer to the section “If you don’t hear any
sound in the Owner’s Manual.This completes assembly and connections.
NOTE
NOTE
Other side
Tighten the bolt with a drum key.
Stopper
Attachthestoppersothattheboltisontheright-handside,fromtheperformer’sperspective.
1. ConnectthecabletotheTD-9asshownintheillustration.Inserttheconnectoralltheway,thenturntheknobstofastenitsecurely.
* Insert the plug firmly, making sure it’s all the way in.
D: Cymbal mounts
C: Pad mounts
A: Hand knobs
B: Snare pipeIfthestandwobbles,loosenthishandknobandadjusttheheight.
Youdonotneedtoattachthehi-hatmount.
Assoonasyouopenthepackage,checktoseethatallitemsareincluded.Ifanythingismissing,pleasecontactyourdealer.* Use a commercially available kick pedal.
Head replacement procedure
* Be sure to adjust the head tension of the PD-85 / PD-105 before use.
* Striking the head when the head tension is loose may damage the sensor and head.
* Do not apply excessive force to the sensor located below the center of the head of the PD-85/PD-105. Doing so can interfere with accurate detection, and may damage it.
* Due to the nature of the materials used in the sensor of the PD-85/PD-105, changes in room temperature may affect the sensitivity of the sensor.
* The rubber portion of the hoop is a consumable item that will undergo wear with use over time, depending on the number and strength of rim shots. Playing rim shots on the worn rubber portion may cause malfunc-tions. If this occurs, the hoop rubber should be replaced. Please contact Roland customer service regarding replacement of the hoop rubber.
Detailed explanation of each part
■ PD-85 (Tom)
PD-85 component names PD-105 component names
1. Removealltuningboltsandwashers.
* While you remove the tuning bolts, press your finger against the lock bushing so that it does not come out of the frame.
* The lock bushing is a part that prevents vibration of the hoop from turning and loosening the tuning bolts when you play rim shots.
2. Removethehoop.
3. Removetheoldhead.
4. Placethenewheadontheframe.
5. Placethehooponthehead.
6. Passthewashersoverthetuningbolts,andattachthemtothehoopandframe.
7. Adjusttheheadtension.Fordetails,refertotheexplanationontheoppositesideofthisleaflet.
Ifalockbushingcomesoutoftheframewhileyou’rereplacingthehead,alignthelockbushing’sslotswiththe“+”shapedportionoftheframe,andpressitfirmlyintotheframe.
■ PD-105 (Snare)
■ CY-12C (Crash) ■ CY-13R (Ride)
* Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad’s function.
CY-12C component names CY-13R component names01
■ KD-9 (Kick)
Positionthebeatersothatitstrikesthecenterofthehead,thensecurethekickpedalandKD-9firmlyinplace.
Step on the kick pedal and make sure that it’s properly attached and in a stable position.
Adjusting the Anchor Bolts
Whenusingthekickpedalonacarpetoronadrummat(TDMseries),theslip-preventiontapethat’sonthebaseshouldpreventtheKD-9frommovingaround.However,ifthat’snotenoughtokeeptheKD-9inafixedposition,youcanadjustthingssothatthetipsoftheanchorboltsprotrudethroughthebase.Thatshouldkeepitinplaceandmakeiteasierforyoutoplay.
KD-9 component names
* Use a commercially available kick pedal.
Attach the kick pedal
ChecktomakesurethatthebaseoftheKD-9andthekickpedalbothmakecontactwiththefloor.
When Using a Twin PedalPositionthetwobeatersequallyapartfromthecenterofthepadasshowninthefigureatleft.Ifoneofthebeaterisfurtherawayfromthecenterthantheother,thesoundfromthefurtherbeaterwillbelowerinvolume,orwillnotsoundasdesired.Usingatwinpedalwillresultinlowersensitivityascomparedtowhenasinglepedalisused.Raisethesensitivityonthesoundmodule.Fordetails,see“Editingthepadsettings[F2](BASIC)”intheowner’smanual.
* Install the kick pedal securely.* Take care not to pinch your
fingers.
* When used on flooring, the anchor bolts may damage the floor.
* The tips of the anchor bolts are sharp. Handle with care.
Whenusingonthecarpetordrummat
Whenusingonthefloor
Beater
Installthekickpedalsecurely.
02
03
Checktobesurethey’remakingcontactwiththefloor
Bolt
Head
Anchorbolts
Base
OUTPUTjack
Mountingplateforthekickpedal
* Depending on how you’re using the unit, the bolts that attach the pedal to the plate could become loose, causing the pedal to rattle during performance. In such cases, use commercially available tools to tighten the bolts.
Hoop (Rim)
Tuning bolt
Washer
Sensor
Wing bolt
Head
OUTPUT jack
FrameHolder
Wing nut
Head Hoop (Rim)
Tuning bolts
Lugs
OUTPUT jackShell
Bracket
Frame
NOTETheheadisanexpendableitemthateventuallywillwearoutandneedtobereplaced.Replacetheheadwhenthefollowingoccurs:Slackportionsremainintheheadevenwhentheheadtensionisproperlyadjusted.
* To obtain replacement heads, please contact the nearest Roland Service Center or an authorized Roland distributor, as listed in “Information.”
Drum key
Loosen Tighten
Hoop
Hoop’srubber portion
Lock bushing
Washer
Frame
Tuning bolt
Lock bushing
Frame
NOTE
Edge
Pad face
Bow
BOW/EDGEOUTPUT jack
Edge
Pad face
BowBell
BELLOUTPUT jack
BOW/EDGEOUTPUT jack
Fixing the cables (CY-12C/CY-13R)
Securethecableinplacewiththecabletie
Leavesomeslackinthecable
Besuretomakethissmallplastichookvisiblefromyou.
Windacabletiearoundthepipeandtightenitinordertonottoslip.
Windacabletiearoundacable.
Insertthesmallplastichooktoaholetosecurethecabletothecymbalarm.
NOTE
WARNING
• Donotopenorperformanyinternal
modificationsontheunit.
• Donotattempttorepairtheunit,or
replacepartswithinit(exceptwhenthis
manualprovidesspecificinstructions
directingyoutodoso).Pleaseconsult
anauthorizedRolanddistributororthe
nearestRolandServiceCenter;alist
ofthesecanbefoundintheowner’s
manualforthedevicetowhichyouare
connecting.
• Neverinstalltheunitinanyofthe
followinglocations.
• Subjecttotemperatureextremes
(e.g.,directsunlightinanenclosed
vehicle,nearaheatingduct,ontop
ofheat-generatingequipment);
orare
• Damp(e.g.,baths,washrooms,on
wetfloors);orare
• Exposedtosteamorsmoke;orare
• Subjecttosaltexposure;orare
• Humid;orare
• Exposedtorain;orare
• Dustyorsandy;orare
• Subjecttohighlevelsofvibration
andshakiness.
• Thisunitshouldbeusedonlywith
astand(MDSseries)thatisrecom-
mendedbyRoland.
• Whenusingtheunitwithastand(MDS
series)recommendedbyRoland,the
stand(MDSseries)mustbecarefully
placedsoitislevelandsuretoremain
stable.Ifnotusingastand(MDSseries),
youstillneedtomakesurethatany
locationyouchooseforplacingthe
unitprovidesalevelsurfacethatwill
properlysupporttheunit,andkeepit
fromwobbling.
WARNING
• Donotplacecontainerscontaining
liquidonthisproduct.Neverallow
foreignobjects(e.g.,flammableobjects,
coins,wires)orliquids(e.g.,wateror
juice)toenterthisproduct.Doing
somaycauseshortcircuits,faulty
operation,orothermalfunctions.
• Inhouseholdswithsmallchildren,an
adultshouldprovidesupervisionuntil
thechildiscapableoffollowingallthe
rulesessentialforthesafeoperationof
theunit.
• Protecttheunitfromstrongimpact.
(Donotdropit!)
CAUTION
• Trytopreventcordsandcablesfrom
becomingentangled.Also,allcords
andcablesshouldbeplacedsotheyare
outofthereachofchildren.
• Neverclimbontopof,norplaceheavy
objectsontheunit.
• Shouldyouremovenuts,washers,
screws,anchorbolts,etc.,keepthem
inasafeplaceoutofchildren’sreach,
sothereisnochanceofthembeing
swallowedaccidentally.
Placement• Donotexposetheunittodirectsunlight,place
itneardevicesthatradiateheat,leaveitinside
anenclosedvehicle,orotherwisesubjectitto
temperatureextremes.Excessiveheatcandeformor
discolortheunit.
• Whenmovedfromonelocationtoanotherwherethe
temperatureand/orhumidityisverydifferent,water
droplets(condensation)mayforminsidetheunit.
Damageormalfunctionmayresultifyouattemptto
usetheunitinthiscondition.Therefore,beforeusing
theunit,youmustallowittostandforseveralhours,
untilthecondensationhascompletelyevaporated.
• Donotallowrubber,vinyl,orsimilarmaterialsto
remainonthisunitforlongperiodsoftime.Such
objectscandiscolororotherwiseharmfullyaffect
thefinish.
Maintenance• Foreverydaycleaningwipetheunitwithasoft,
dryclothoronethathasbeenslightlydampened
withwater.Toremovestubborndirt,useacloth
impregnatedwithamild,non-abrasivedetergent.
Afterwards,besuretowipetheunitthoroughlywith
asoft,drycloth.
(KD-9)
Asroutinemaintenance,youshouldwipethestriking
surfaceusingadry,softcloth.
• Neverusebenzine,thinners,alcoholorsolventsof
anykind,toavoidthepossibilityofdiscolorationand/
ordeformation.
Additional Precautions• Useareasonableamountofcarewhenusingthe
outputjacks.Roughhandlingcanleadtomalfunc-
tions.
• Whenconnecting/disconnectingallcables,grasp
theconnectoritself—neverpullonthecable.This
wayyouwillavoidcausingshorts,ordamagetothe
cable’sinternalelements.
• Toavoiddisturbingyourneighbors,trytokeep
theunit’svolumeatreasonablelevels.Youmay
prefertouseheadphones,soyoudonotneedtobe
concernedaboutthosearoundyou.
• Thisinstrumentisdesignedtominimizethe
extraneoussoundsproducedwhenit’splayed.
However,sincesoundvibrationscanbetransmitted
throughfloorsandwallstoagreaterdegreethan
expected,takecarenottoallowthesesoundsto
becomeanuisancetoneighbors,especiallywhen
usingheadphones.
• Whenyouneedtotransporttheunit,packageit
inthebox(includingpadding)thatitcamein,if
possible.Otherwise,youwillneedtouseequivalent
packagingmaterials.
• Someconnectioncablescontainresistors.Donotuse
cablesthatincorporateresistorsforconnectingto
thisunit.Theuseofsuchcablescancausethesound
leveltobeextremelylow,orimpossibletohear.For
informationoncablespecifications,contactthe
manufacturerofthecable.
• Therubberportionofthestrikingsurfaceistreated
withapreservativetomaintainitsperformance.With
thepassageoftime,thispreservativemayappearon
thesurfaceasawhitestain,orrevealhowthepads
werestruckduringproducttesting.Thisdoesnotaf-
fecttheperformanceorfunctionalityoftheproduct,
andyoumaycontinueusingitwithconfidence.
• Continuousplayingmaycausedis-colorationofthe
pad,butthiswillnotaffectthePad’sfunction.
• Thehi-hatstandissupportedbymeansofatripod.
Wheninstallingthehi-hat,makesurethelegsof
thetripodareopenedwideenoughtokeepthe
equipmentfromfallingover.
• DonotremovethespecialVH-11clutchfromthe
hi-hatordisassembletheclutch.
• Whennotusingthehi-hatforextendedperiods,
storethehi-hatintheopenpositiontoprevent
placinganystressonthemotionsensorunit.
• High-precisionsensorsarelocatedattheportionof
themotionsensorunitindicatedbythearrowinthe
leftfigurebelow.Takecarenottosubjectthisareato
excessiveshock,anddonotallowanyforeignobjects
toenteranygaps.
• Overlongperiodsofuse,theportionofthemotion
sensorunitthatcomesintocontactwiththehi-hat
(thedamper)maybecomewornatthepoints
indicatedbythearrowsintherightfigureabove.
Suchdamperwearmaypreventproperadjustment
oftheoffsetandmaycausethehi-hattoswing
withanunnaturalmotion.Ifthisoccurs,replace
thedamper.Formoreinformationonreplacingthe
damper,contactRolandService.
• Intheinterestofproductimprovement,thespecifica-
tionsand/orappearanceofthisunitaresubjectto
changewithoutpriornotice.
IMPORTANT NOTES For EU Countries
For China
WARNINGThis product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US (Proposition 65)
Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.
* Material damage refers to damage or other adverse e�ects caused with respect to the home and all its furnishings, as well to domestic animals or pets.
Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
The symbol alerts the user to things that must be carried out. The speci�c thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power-cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or warnings.The speci�c meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be carried out (are forbidden). The speci�c thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.
About WARNING and CAUTION Notices About the Symbols
ALWAYS OBSERVE THE FOLLOWING
Base
Slip-preventiontape
Top Related