Training Center
Workshop Manual
ATLAS 1305 / 1505 / 1605 /1705
Training Center
The present Workshop Manual was compiled specifically for service technicians belonging to the ATLAS TEREX organization.
Generally, service technicians work under their own responsibility for industrial safety during maintenance and repair work on ATLAS TEREX products.
In order to prevent personal and material dama-ge, it is necessary to observe all effective safety instructions and legal regulations.
Only qualified and trained specialists are autho-rized to service and repair ATLAS TEREX pro-ducts properly.The service technicians are obliged to perform training courses.
For machine care and maintenance work, refer to the Operating Manuals.
The contents of this Manual is in the property of ATLAS TEREX GmbH, Delmenhorst, Germany, and protected by copyright. No part of this docu-ment may be reproduced.
ATLAS-TEREX GmbH Delmenhorst / Germany Tel.: 04221 / 491 - 0e-Mail: [email protected]
Revised: 08.2004Order Nr.: xxxxxxx
Workshop manual1305 / 1505 / 1605 /1705 Mobile
Page 1 of 1
Training CenterRevised: 08.2004
Contents1 Technical data
2 Display and controls
3 Engine
4 Vehicle engine
5 Pumps
6 Pilot Control Equipment
7 Control block
8 Main rotation connection
9 Slewing gear gears and motor
10 Pressure setting tables / setting regulations
11 Cylinders
12 Hydraulic accessories
13 Air conditioner system
14 Power shift transmission
15 Electricity
16 Axles
17 Hydraulic circuit diagrams
18 Maintenance
19 Miscellaneous
Training CenterRevised: 08.2004
Workshop Manual1305 / 1505 / 1605 / 1705 Mobile
Page 2 of 16 Chapter 2Display and controls
9
6
8
7
5
4 4
10
17 151416
1312
1118
12
3
M+P-05C-0035
1 General view of cab
1 Slider, side window2 Lever for cab door3 Lever for pilot control4 Windshield locking rods left/right5 Side window6 Multifunction lever7 Windshield vent outlet8 Side window vent outlet9 Sun visor
10 Windshield11 Right console with switch panels12 Superstructure slewing lock13 Accelerator pedal14 Brake pedal with lock15 Foot lever for adjusting angle of steering column16 Foot lever for adjusting angle of steering column17 Boom adjusting peda18 Left console with switch panel
Workshop Manual1305 / 1505 / 1605 / 1705 Mobile
Training CenterRevised: 08.2004
Page 31 of 32Chapter 7Control block
2.5 1505 / 1605 control block, Picture 2
130 Sealing set131 Spring plate132 Pressure spring134 Cap135 Socket head cap screw136 Sealing set141 Flap valve142 Flap valve156 Socket head cap screw157 Cap241 Piston242 Piston243 Piston244 Piston245 Piston292 Pressure spring294 Reducer295 O-ring296 Vent screw298 Piston299 Ring
Training CenterRevised: 08.2004
Workshop Manual1305 / 1505 / 1605 / 1705 Mobile
Page 70 of 120 Chapter 14Power shift transmission
Insert the axle conical gear wheel.
Mount the complete differential spider and put on the 2. axle conical gear wheel.
Please note: Pay attention to a radial installation position of the stop discs - noses point upwards - see arrow!
Stick the stop disc into the differential cage half II with grease.
Put on the differential cage half.
Please note: ensure a radial installation position
Attach the differential by means of a press.
Insert the segments and tighten the pan head screws.
Torque moment (M15x1, 5/12.9) ... MA = 145 Nm
Top Related