Download - 10Gb/s DWDM SFP+ 40km Transceiver RDPX0SER · Rev. A.2 5, 07/19/2013 RDPX0SER DWDM SFP+ Transceiver Product Specifications 1. Absolute Maximum Ratings Parameter Symbol Min. Typ. Max.

RoHS Compliant

Rev. A.5, 07/19/2013 1

Features

RoHS compliant

Support multi protocol from 9.9Gb/s to 11.3 Gb/s

Compliant with SFP+ MSA, SFF 8431 Rev. 4.1

Compliant with SFF 8432 Rev.5.0 mechanical

dimension

Compliant with Digital diagnostic SFF-8472

Rev.11.0

Transmission distance of 40km over single mode

fiber

C-band DWDM EML laser transmitter

LC duplex connector

Hot pluggable 20 pin connector

Single power supply voltage : +3.3V

Low power dissipation

Three optional operating temperature ranges :

Option ST : 0°C to 70°C

Option ET : -5°C to 85°C

Option IT : -40°C to 85°C

Applications

SONET OC-192 IR-2 / SDH L-64.2b

10GBASE-ER

10G Fiber channel

G.709 OUT-2

Description

OE Solutions’ Small Form Factor Pluggable

(SFP+) transceivers are compatible with the

Small Form Factor Pluggable 20pin Multi-

Source Agreement (MSA). The high performance

cooled DWDM EML transmitter and high

sensitivity PIN receiver provide superior

performance for SONET/SDH and Ethernet

applications up to 40km optical links.

Enhanced Digital Diagnostics functions are

available via the 2-wire serial bus specified in the

SFF-8472 Rev. 11.0. The transmitter and receiver

features ac-coupled differential data inputs and

outputs, and an LVTTL for Tx disable input and

Tx fault output. Software TX disable is also

implemented. The receiver features differential

ac-coupled data outputs and LVTTL for LOS

(Loss of Signal) output.

10Gb/s DWDM SFP+ 40km Transceiver

RDPX0SER

Rev. A.5, 07/19/2013 2

RDPX0SER DWDM SFP+ Transceiver Product Specifications

1. Absolute Maximum Ratings

Parameter Symbol Min. Typ. Max. Unit Notes

Absolute Supply Voltage Vcc_max 0 - 3.6 V -

Operating Case Temperature Top -40 - 85 °C 1,3

Operating Relative Humidity RHop 5 - 90 % 2

Storage and TransportationTemperature Tst -40 - 85 °C 2

Storage and Transportation

Relative Humidity

5 - 95 % 2

Notes: 1. Measured on top side front center of SFP module 2. Non-condensing 3.There are three options of operating maximum temperature:

Option ST: standard temperature from 0oC to 70

oC,

Option ET: extended temperature from -5oC to 85

oC

Option IT: extended temperature from -40oC to 85

oC

2. General Operating Conditions


Bit Rate B 9.9 10.3 11.3 Gb/s -

Maximum Transmission Distance Dmax 80 - - km -

Operating Voltage Vcc 3.14 - 3.46 V -

Power Supply Current ICC - - 550 mA ST

- - 725 mA ET, IT

Total Power Consumption - - 2.5 W -

ESD (High speed pins) - - 500 V 2

Notes : 1. Supplies TEC, Current draw depends on Temperature 2. Human body model per JEDEC JESD22-A114-B, compliant with INF-8077i Rev. 4.5 August 31, 2005

Rev. A.5, 07/19/2013 3


3. Electrical Specifications

3.1 Transmitter Electrical Specifications (Over Operating Case Temperature and Power Supply Range)

Electrical Characteristics


Differential Input Impedance Rin 80 100 120 Ω -

Differential Data Input Swing Vin,pp 180 - 700 mVp-p -

Data Input Rise/Fall Time tr/tf 15 - 40 ps

Tx Disable Voltage Vd 2.0 - Vcc+0.3 V 1

Tx Enable Voltage Ven 0 - 0.8 V -

Tx Fault Output Low Vtfl - - 0.4 V -

Tx Disable Assert Time T_off - - 100 s -

Tx Enable Assert Time T_on - - 2 ms -

Tx Fault Assert Time Tx_f_on - - 1 s -

Tx Fault Reset Time Tx_reset 10 - - s -

Initialization Time T_start_up_cooled - - 90 s -

Note : 1. Vcc is the voltage of host board

3.2. Receiver Electrical Specifications (Over Operating Case Temperature and Power Supply Range)

Electrical Characteristics


Data Rate B 9.9 10.3 11.3 GBd -

Differential Output Impedance Rout 80 100 120 Ω -

Differential Data Output Swing Vout 350 - 800 mVp-p -

Data Output Rise/Fall Time tr/tf - - 45 ps -

LOS Output High Voltage Vlosh Vcc-0.5 - Vcc+0.3 V 1

LOS Output Low Voltage Vlosl 0 - 0.4 V -

LOS Assert/Deassert Time Delay T_los on/off - - 100/100 s/s -

Note : 1. Vcc is the voltage of host board

Rev. A.5, 07/19/2013 4


4. Optical Specifications

4.1 Transmitter Optical Specifications (Over Operating Case Temperature and Power Supply Range)

Optical Characteristics


Laser Safety Class Class 1 according to IEC60825 -

Optical Wavelength λ 1529 - 1562 nm -

Average Optical

Output Power

BOL Pout -1 - +3 dBm 1

EOL -2 - +3

Optical Power Overshoot Pov - - 1 dB 2

Optical power of OFF transmitter Pout-off - - -40 dBm -

Spectral Width -8 - 8 GHz 3

Optical Output Power Variation

(with respect to BOL Tc=25C,

and nominal power supply)

Pout -1 - +1 dB -

Side Mode Suppression Ratio SMSR 35 - - dB 4

Wavelength

Deviation

BOL T -50 - +50 pm 5

EOL a -100 - +100 pm

Optical Extinction Ratio ER 8.2 - - dB -

Optical Rise/Fall Time (20%-80%) Tr, Tf - - 35 ps -

Output Jitter - - - - 6

Date Rate 9.95 10.7 11.05 11.35 Gb/s

Path Penalty 10-3

BER 3 3.5 4

dB 7 10-4

BER 3 3.5 4

10-12

BER 2

Notes: 1. Average power measured at output 2. Defined as Peak power – Steady-state power (in dBm) when Tx-dis is de-asserted or when the module is hot plugged with Tx_dis in low state (Tx enabled). 3. Full spectral width (RBW=0.1nm) measured 15dB down from the maximum of center wavelength peak under full modulation condition 4. Ratio of the average output power in the dominant longitudinal mode to the power in the most significant side mode peak under full modulation condition 5. Deviation related to the ITU standardized wavelength. The EOL value is met as soon as the output average power is above 10% of the steady-state power. 6. The jitter performance meets Telcodia GR-253-Core and ITU-T Recommendations G.783, G813, G825 and G82511 with ITU-T 0.172(04/2005) for the measurement methods and the measurement equipment. 7. -500 to 800ps/nm

Laser Safety: All transceivers in this datasheet are Class I Laser products per FDA/CDRH and IEC-60825 standards.

They must be operated under specified operating conditions.

Rev. A.5, 07/19/2013 5


4. ITU Channel and Wavelength Guide

ITU Channel Frequency

(THz)

Wavelength

(nm) ITU Channel

Frequency

(THz)

Wavelength

(nm)

39 193.9 1546.12

40 194.0 1545.32

17 191.7 1563.86 41 194.1 1544.53

18 191.8 1563.05 42 194.2 1543.73

19 191.9 1562.23 43 194.3 1542.94

20 192.0 1561.42 44 194.4 1542.14

21 192.1 1560.61 45 194.5 1541.35

22 192.2 1559.79 46 194.6 1540.56

23 192.3 1558.98 47 194.7 1539.77

24 192.4 1558.17 48 194.8 1538.98

25 192.5 1557.36 49 194.9 1538.19

26 192.6 1556.56 50 195.0 1537.40

27 192.7 1555.75 51 195.1 1536.61

28 192.8 1554.94 52 195.2 1535.82

29 192.9 1554.13 53 195.3 1535.04

30 193.0 1553.33 54 195.4 1534.25

31 193.1 1552.52 55 195.5 1533.47

32 193.2 1551.72 56 195.6 1532.68

33 193.3 1550.92 57 195.7 1531.90

34 193.4 1550.12 58 195.8 1531.12

35 193.5 1549.32 59 195.9 1530.33

36 193.6 1548.51 60 196.0 1529.55

37 193.7 1547.72 61 196.1 1528.77

38 193.8 1546.92

Rev. A.5, 07/19/2013 6


4.2. Receiver Optical Specifications (Over Operating Case Temperature and Power Supply Range)

Optical Characteristics


Optical Wavelength λ 1528 1563 nm -

Average Rx Sensitivity@10GBd RSENS - - -15.8 dBm 1

Maximum Input Power Pol -1.0 - - dBm -

Rx Sensitivity@10GBd (OMA) - - - -14.1 dBm 2

Stressed Sensitivity@10GBd (OMA) - - - -11.3 dBm 3

Receiver Reflectance - - - -26 dB -

LOS Assert LOS_A -30 - - dBm -

LOS De-assert LOS_D - - -16 dBm -

LOS Hysteresis - - 2 5 dB -

Notes : 1. Measured with a PRBS of 231

-1 at 1 x 10-12

BER and 3 dB extinction ratio

Rev. A.5, 07/19/2013 7


5. Pin Descriptions

SFP Transceiver Electrical Pad Layout

Tx GND

TD-

TD+

Tx GND

VccT

VccR

Rx GND

RD+

RD-

Rx GND

Tx Fault

Tx Disable

SDA

RS0

Rx_LOS

RS1

Rx GND

SCL

Mod_ABS

20

19

18

17

16

15

14

13

12

11

1

2

3

4

5

6

7

8

9

10

Top of Board Bottom of Board

Tx GND

Rev. A.5, 07/19/2013 8


Pin Descriptions (continued)

Pin Logic Symbol Description Plug Seq. * Notes

1 - Tx GND Transmitter Ground 1 1

2 LVTTL-O Tx Fault Transmitter Fault Indication 3 2

3 LVTTL-I Tx Disable Transmitter Disable 3 3

4 LVTTL-I/O SDA 2 wire Serial Interface Data Line 3 4

5 LVTTL-I/O SCL 2 wire Serial Interface Clock 3 4

6 -

MOD_ABS Module Absent, connected to Tx GND or Rx GND in the module

3 5

7 LVTTL-I RS0 Rate Select 0, not used 3 6

8 LVTTL-O Rx LOS Receiver Loss of Signal Indication (In FC designated as Rx_LOS and in Ethernet designated as Signal Detect Bar

3 7

9 LVTTL-I RS1 Rate Select 1, not used 3 6

10 - Rx GND Receiver Ground 1 1


12 CML-O RD- Receiver Negative Data Out 3 -

13 CML-O RD+ Receiver Positive Data Out 3 -


15 - Vcc Rx Receiver Power, 3.3V±5% 2 -

16 - Vcc Tx Transmitter Power, 3.3V±5% 2 -

17 - Tx GND Transmitter Ground 1 1

18 CML-I TD+ Transmitter Positive Data In 3 -

19 CML-I TD- Transmitter Negative Data In 3 -

20 - Tx GND Transmitter Ground 1 1 *Plug Seq. : Pin engagement sequence during hot plugging Notes : 1. The module ground contacts, Tx GND abd Rx GND, shall be isolated frim the module case, that is, frame ground. 2. Tx Fault is an open collector/drain output that shall be pulled up with a 4.7k ~ 10k on the host board. Pull up voltage

between 2.0V and VccT + 0.5V. When high, output indicates a laser fault of some kind. When low, output indicates normal operation. The LD output is not turned off in case of Tx Fault

3. Tx Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the TRx with a 4.7k ~ 10k to VccT.

4. SDA and SCL should be pulled up with a 4.7k ~ 10k on the host board. The pull-up voltage shall be VccT. SCL is the clock line of 2-wire serial interface for serial ID. SDA is the data line of 2-wire serial interface for serial ID.

5. Mod_ABS is connected to Tx GND or Rx GND in the SFP+ module. The host may pull the contact up to Vcc on the host board with a resistor in the range 4.7 ~ 10k. Mod_ABS is asserted “high” when the SFP+ module is physically absent from a host slot. In the SFP MSA (INF-8074i) this contact has the same function but is called MOD_DEF0.

6. RS0 and RS1 are module input rate select contacts and are pulled low to Tx GND with a >30k resistor in the module. RS0 is an input hardware contact which optionally selects the optical receive data path rate coverage for an SFP+ module. RS1 is an input hardware contact which optionally selects the optical transmit path data rate coverage for the SFP+ module. These contacts can also be used for AS0 and AS1 if implementing SFF8079. RS1 is commonly connected to Tx GND or Rx GND in the classical SFP modules. The host needs to ensure that it will not be damaged if this contact is connected to Tx GND or Rx GND in the module. For logical definitions of RS0/RS1, see Section 2.5 of SFF-8431 Rev. 2.1.

7. LOS is an open collector output. Shall be pulled up with a 4.7k ~ 10k on host board. Pull up voltage between 2.0 and VccR+0.3. Logic 0 indicates normal operation.

Rev. A.5, 07/19/2013 9


5. Outline Drawings

Dimensions are in millimeters

Rev. A.5, 07/19/2013 10


6. PCB layout and Bezel recommendation

Dimensions are in inches (millimeters)

Notes : 1. Datum and basic dimensions established by customer.

2. Pads and vias are chassis ground, 11 locations

3. Thru holes, plating optional.

Rev. A.5, 07/19/2013 11


7. PCB layout and Bezel recommendation (continued)

Notes : Thru holes, plating optional.

Recommended Panel Opening

Rev. A.5, 07/19/2013 12


8. SFP+ Block Diagram, Power Supply Information and Host Board Interface

8.1 SFP+ Block Diagram

TOSA

TOSA

Laser

driver

Post amp.

Vcc Tx

Tx_GND

LOS

RD-

RD+

TD+

TD-

Tx Disable

Tx Fault

SCL

SDA EEPROM

10k

100

Management processor

Vcc Rx

Rx_GND

Zin diff.=

100

Zout = 50

each arm

Pin 16

Pin 3

Pin 18

Pin 19

Pin 2

Pin 1, 17, 20

Pin 5

Pin 4

Pin 15

Pin 12

Pin 13Pin 8

Pin 10, 11, 14

RS0

RS1

Pin 7

Pin 9

Mod ABS Pin 6

Rev. A.5, 07/19/2013 13


8.2 Recommended Host Board Supply Filtering Network

8.3 SFP+ Host Board Interface

Note 1: Host board output device circuit in the transmitter side and host board input device circuit in the receiver should be

carefully designed to meet 100ohm differential impedance matching. Also necessary is the dc bias circuit of each

input and output by taking into account of ac coupling of data input ant output of SFP+ module. For the interface of

host board devices, it is recommended to refer to the device vendor’s data sheet.

1H

1H

0.1F

0.1F

10F 10F 0.1F

Vcc +3.3V

SFP+ Module

Vcc Tx

Vcc Rx

HOST BOARD

Tx GND

Rx GND

Host Board GND

1 Tx GND

2 Tx Fault

3 Tx Disable

4 SDA

5 SCL

6 Mod ABS

7 RS0

8 Rx LOS

9 RS1

10 Rx GND

Tx GND 20

TD- 19

TD+ 18

Tx GND 17

Vcc Tx 16

Vcc Rx 15

RX GND 14

RD+ 13

RD- 12

Rx GND 11

10k

Vcc

10k

Vcc

10k

Vcc

10k

Vcc

10k

Vcc

Host board

Device

Host board

Device

Differential 100(note 1)

Differential 100(note 1)

Refer to Section 8.2

SFP+ Module

Rev. A.5, 07/19/2013 14


9. Digital Diagnostic Monitoring and Serial ID Operation

The information is accessed through the pin 4 (SDA), and pin 5(SCL) of the module. The device

address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is

1010001X(A2h). The EEPROM Write Protect pin is internally tied to ground with no external access,

allowing write access to the customer-writable field (bytes 128-247 of address 1010001X). Address

bytes 0-127 are not write protected and may cause diagnostic malfunctions if overwritten.

The information stored in the EEPROM, including the organization and the digital diagnostic

information, is defined in the Small Form-Factor document SFF-8472 Rev. 11.0, dated September,

2010.

9.1 Data Field Descriptions, and Serial ID Data and Map

9.2 Serial ID and Map: page A0h

Address HEX Name of Fields Description

0 03 Identifier SFP+

1 04 Ext. Identifier GBIC/SFF function is defined by serial ID only

2 07 Connector LC

3 80 10G Ethernet Compliance 10GBASE-ER

4 00 Reach Specifier

5 00 SONET

6 00 Gigabit Ethernet

7 00 Fiber Channel link length Unallocated

8 10 Transmitter technology Longwave Laser (LL)

9 01 Transmission media Single Mode (SM)

10 00 Fiber Channel Speed

Address(1010000X) (A0h) Address(1010001X) (A2h)

Serial ID Information:

Defined by SFP MSA

OE Solution Specific

Information

Reserved for SFP MSA

Alarm and Warning Limits

Reserved for External

Calibration Constants

Real Time Diagnostic

Information

OE Solutions Specific

Information

OE Solutions Specific Information

Non-volatile, customer-

writeable, field-writeable

area

0

95

127

255 255

247

119

127

95

0

55

Rev. A.5, 07/19/2013 15


11 06 Encoding 64B/66B

12 67 Nominal Bit Rate 10.30 Gbps

13 00

14 28 Length(9u)[km] 40 Km

15 FF

16 00 Length(50u,OM2)[m] Not support

17 00 Length(62.5u,OM1)[m] Not support

18 00 Length(copper) Not support

19 00 Length(50u,OM3)[m] Not support

20 4F

Vendor Name

O

21 45 E

22 20

23 53 S

24 4F O

25 4C L

26 55 U

27 54 T

28 49 I

29 4F O

30 4E N

31 53 S

32-35 20

36 00 Reserved

37 00

Vendor OUI

00

38 19 19

39 3A 3A

40 52

Vendor PN

R

41 44 D

42 50 P

43 58 X

44 30 0

45 53 S

46 45 E

47 52 R

48 2D -

49 xx xx = (5Ah for ST, 45h for ET, 49h for IT)

50 xx xx=(32h:2,33h:3,34h:4,35h:5,36h:6)

51 xx xx=(30h:0, 31h:1, 32h:2,33h:3,34h:4,35h:5,36h:6,37h:7,

38h:8, 39h:9)

52-55 20

56 30

Vendor Rev.

0

57 31 1

58 2E .

59 varies varies

60

Note 1 Wavelength[nm]

61

62 Wavelength(@10pm)

63 Varies CC_BASE Checksum over 0 to 62

64 06

Option Values

Cooled Transceiver[2]

Power Level[1]

Linear Receiver Output[0]

Cooled Laser implementation

Power Level 2

Rev. A.5, 07/19/2013 16


65 1A

Option Values

Rate Select[5]

Tx Disable[4]

TX Fault[3]

SD[2]

LOS[1]

Tx Disable[4]

TX Fault[3]

LOS[1]

66 00 Bit Rate, max[%] Not Specified

67 00 Bit Rate, min[%] Not Specified

68-83 Varies Vendor S/N Varies

84-91 Varies Date Code Varies

92 68

Diagnostic Monitoring Type

Digital diagnostic[6]

Internally Cailbrated[5]

Externally Calibrated[4]

Average Power[3]

Address change req[2]

Digital diagnostic[6]

Internally Calibrated[5]

Average Power[3]

93 F0

Enhanced Options

Alarm/Warm Impl.[7]

Soft TX Dis Control[6]

Soft TX Fault monitor[5]

Soft Rx LOS monitor[4]

Soft RATE_SEL Control[3]

App Select Control[2]

Rate Select Control[1]

Alarm/Warm Impl.[7]

Soft TX Dis Control[6]

Soft TX Fault monitor[5]

Soft Rx LOS monitor[4]

94 05 SFF-8472 Compliance Rev 11.0 of SFF-8472

95 Varies CC_EXT Check Sum Byte for Bytes 64 to 94

96-127 00 Vendor Specific

128-163 Varies OES'DATA OES'DATA

164-247 00 Reserved Reserved

248-255 Varies OES'DATA OES'DATA

Note 1. 16-bit integer value in nm with byte 60 as high byte, byte 61 as low byte. The fractional part of the

wavelength in units of 0.01nm written in byte 62. Varies

9.3. Page A2 HEX

Address HEX Name of Fields Description

0 49/58 Temp High Alarm ST:73.00/ET,IT:88.00

1 00

2 F8/D5 Temp Low Alarm ST,ET:-8.00/IT:-43.00

3 00

4 46/55 Temp High Warning ST:70.00/ET,IT:85.00

5 00

6 FB/D8 Temp Low Warning ST,ET:-5.00/IT:-40.00

7 00

8 8C Voltage High Alarm 3.60

9 A0

10 75 Voltage Low Alarm 3.00

Rev. A.5, 07/19/2013 17


11 30

12 87 Voltage High Warning 3.47

13 8C

14 79 Voltage Low Warning 3.10

15 18

16 EA Bias High Alarm 120.00

17 60

18 4E Bias Low Alarm 40.00

19 20

20 D6 Bias High Warning 110.00

21 D8

22 61 Bias Low Warning 50.00

23 A8

24 7B Tx High Alarm 5.00

25 87

26 13 Tx Low Alarm -3.00

27 94

28 4D Tx High Warning 3.00

29 F1

30 1F Tx Low Warning -1.00

31 07

32 27 Rx High Alarm 0.00

33 10

34 00 Rx Low Alarm -17.00

35 C8

36 1F Rx High Warning -1.00

37 07

38 01 Rx Low Warning -15.00

39 3C

40-55 00 Reserved

56 00

Rx PWR(4) 0.00 57 00

58 00

59 00

60 00

Rx PWR(3) 0.00 61 00

62 00

Rev. A.5, 07/19/2013 18


63 00

64 00

Rx PWR(2) 0.00 65 00

66 00

67 00

68 3F

Rx PWR(1) 1.00 69 80

70 00

71 00

72 00

Rx PWR(0) 0.00 73 00

74 00

75 00

76 01 Bias (Slope) 1.00

77 00

78 00 Bias (Offset) 0.00

79 00

80 01 Tx Power (Slope) 1.00

81 00

82 00 Tx Power (Offset) 0.00

83 00

84 01 Temp (Slope) 1.00

85 00

86 00 Temp (Offset) 0.00

87 00

88 01 Vcc (Slope) 1.00

89 00

90 00 Vcc (Offset) 0.00

91 00

92 00

Reserved

93 00

94 00

95 xx Checksum Checksum over 0 to 94

96 00 Temperature MSB

97 00 Temperature LSB

98 00 Vcc MSB

99 00 Vcc LSB

Rev. A.5, 07/19/2013 19


100 00 TX Bias MSB

101 00 TX Bias LSB

102 00 TX Power MSB

103 00 TX Power LSB

104 00 RX Power MSB

105 00 RX Power LSB

106 00

107 00

108 00

109 00

110 00

Optional Status

Tx Disable Input[7]

Soft TX Disable[6]

RX Rate Select State[4]

Tx Fault Output[2]

Loss of Signal Output[1]

Data_Ready_Bar[0]

111 00

112 00

Alarm Flag

Temp High Alarm[7]

Temp Low Alarm[6]

Vcc High Alarm[5]

Vcc Low Alarm[4]

TX Bias High Alarm[3]

TX Bias Low Alarm[2]

TX Power High Alarm[1]

TX Power Low Alarm[0]

113 00 RX High Alarm[7]

RX Low Alarm[6]

114 00

115 00

Rev. A.5, 07/19/2013 20


116 00

Warning Flag

Temp High Warning[7]

Temp Low Warning[6]

Vcc High Warning[5]

Vcc Low Warning[4]

TX Bias High Warning[3]

TX Bias Low Warning[2]

TX Power High Warning[1]

TX Power Low Warning[0]

117 00 RX High Warning[7]

RX Low Warning[6]

118 00

119 00


128-247 00 User EEPROM


9.4 Diagnostics

The enhanced digital diagnostics feature monitors five key transceiver parameters which are internally

calibrated and should be read as absolute values.

A2h address Parameter Calibration Accuracy Range

96-97 Temperature Internal +/- 3oC Note 1

98-99 Vcc Internal +/- 3% 3.13 to 3.47

100-101 Tx bias Internal +/- 10% Note 2

102-103 Tx power Internal +/- 2dB -2 to +3Bm

104-105 Rx Power Internal +/- 2dB -24 to -7dBm

Note: 1) Junction temperature of temperature sensing device. Monitoring range is from -40oC to 125

oC.

2) Specified by nominal value

10. Regulatory Compliance

RDPX0SER comply with international Electromagnetic Compatibility (EMC) and international safety

requirements and standards. EMC performance is dependent on the overall system design. The RDPX0SER is

lead-free and RoHS-compliant per Directive 2011/65/EU of the European Parliament and of the Council of 8

June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Rev. A.5, 07/19/2013 21


11. Ordering Information

Model Name OES P/C

Operating Case

Temperature

Nominal Wavelength

Latch Color

Application Distance

RDPX0SER-Sxx Gxx05 0oC to 70oC

C-band

DWDM

(See Section 4)

Red SONET/SDH & 10G GbE 40km

RDPX0SER-Exx TBD -5oC to 85oC

C-band

DWDM

(See Section 4)


RDPX0SER-Ixx TBD -40oC to 85oC

C-band

DWDM

(See Section 4)


Notice: This data sheet is subject to change at any time without notice.

Revision History

Date Rev. # Description Author(s)

12/09/2011 Rev.A.0 first Release JSYU

01/07/2012 Rev.A.1 10GBASE-ER Compliance specified in Byte 3

Fiber Channel Technology in Byte 8

JSYU

11/05/2012 Rev.A.2 EEPROM corrections of A0H

Addr 64: 04->06

Addr 65: 3A->1A

A2H content added

JSYU

11/17/2012 Rev.A.3 Typo(Optical Extinction Ratio (Unfiltered) → Optical Extinction Ratio) JSYU

01/08/2013 Rev.A.4 ET,IT Temp added JSYU

07/19/2013 Rev.A.5 Total Current changed

(ET,IT : 700mA → 725mA)

JSYU

Contact Information:

OE Solutions Co. Ltd. (Korea) Techno Park, 958-3, Daechon-Dong, Buk-Gu, Gwangju, Korea, 500-470. Tel: +82-62-602-7813, Fax: +82-62-602-7639, www.oesolution.com.

OE Solutions America, Inc. 560 Sylvan Avenue, 1

st Floor, Englewood Cliffs, NJ 07632

Tel: 201-568-1188 Fax:201-568-1177Tel: +1-201-224-2377, Fax: 1-949-272-3200

http://www.oesolution.com/