1 Exam Prep – OSHA for Business and Finance 1
1 Exam Prep
Business and Finance
OSHA Practice Test
PRACTICE TEST ONE
1. Impact tools, such as drift pins, shall be kept free of .
A. Lint and dust C. Oil
B. Mushroomed heads D. Fungus
2. If an employee wears prescription glasses, OSHA requires that he must be provided with for certain
jobs.
A. Spectacles with protective lenses
B. Goggles over corrective spectacles
C. Goggles with lenses that incorporate corrected lenses mounted behind the protective lenses.
D. Either A, B, or C
3. When employees are working in an excavation, there can be no more than between them
and a means of egress.
A. 5' C. 15'
B. 10' D. 25'
4. The _ has the first responsibility for assuring that the required personal protective equipment is
worn by workers on a construction site defined by OSHA.
A. Employee C. Owner
B. Employer D. Prime contractor
5. Lifelines shall be secured above the point of operation to anchorage or structural members capable of
supporting a minimum dead weight of pounds.
A. 1,000 C. 4,000
B. 2,500 D. 5,400
6. A safety belt lanyard shall be a minimum of one-half inch nylon rope with a maximum length that provides
for a fall of no greater than .
A. 6' C. 12'
B. 10' D. 15'
1 Exam Prep – OSHA for Business and Finance 2
7. Portable firefighting equipment must be maintained on a job site of 1,500 square feet, at all times during
construction.
A. False, only required for each 3,000 square feet.
B. False in all cases.
C. True in all cases.
D. True if the job site is "commercial."
8. Electric power operated tools shall be either grounded or _ type.
A. Approved double-insulated
B. Approved single-insulated
C. #12 Romex
D. Three phase
9. Danger signs shall be _ .
A. 3 C. 8
B. 6 D. 10
10. The maximum loading of a medium duty tube and coupler scaffold is per square foot.
A. 25 C. 35
B. 30 D. 50
11. First aid kits shall consist of materials approved by the consulting physician in a container.
A. Water proof C. Weatherproof
B. Bulletproof D. Fireproof
12. Lumber piles stored on a job site shall not exceed in height provided that manually stacked lumber
shall not be stacked higher than _ _.
A. 20' - 10' C. 24' - 20'
B. 16' - 8' D. 20' -16'
13. The maximum air pressure allowed for nailers, staplers, and other similar type equipment is pressure
at the tool unless the tool shall have a safety device on the muzzle to prevent the tool from
ejecting fasteners.
A. 30 psi C. 100 psi
B. 60 psi D. 150 psi
14. To protect employees working in excavated area from cave-ins, all excavations over 5 feet shall be
protected by a slope and bench system. Unless specifically designed by qualified personnel, excavations shall
not be sloped at an angle steeper than to one.
A. One C. Two
B. One and one-half D. Three
1 Exam Prep – OSHA for Business and Finance 3
PRACTICE TEST TWO
1. All Ladder Jack scaffolds shall be limited to light duty and shall not exceed a height of above the
floor or ground.
A. 10' C. 30'
B. 20' D. 40'
2. Toe boards, where required on scaffolds, shall be a minimum of in height.
A. 2" C. 4"
B. 3-1/2" D. 4-1/2"
3. Which of the following is a typical tool equipped with a constant pressure switch?
A. Circular saw
B. Hydraulic come-along
C. Table saw
D. Jig saw
4. Rungs, steps, and cleats of portable ladders and fixed ladders shall be spaced not less than apart.
A. 8" C. 12"
B. 10" D. 14"
5. The height of handrails shall not be more than nor less than from the upper surface of
the stairwell system to the surface of the tread, in line with the face of the riser at the forward edge of the tread.
A. 37"...30" C. 30"...22"
B. 37"...36" D. 36"...24"
6. The minimum rated fire extinguisher required for a 3,000 square foot building is .
A. 2A C. 2C
B. 2B D. 2D
7. Safety belts and lanyards (ropes) should be nylon or material of equivalent strength and have a minimum
diameter of .
A. 1/4" C. 3/4"
B. 1/2" D. 1"
8. The minimum acceptable clearance between a crane load and an electric service of 50 kV is?
A. 10' C. 15'
B. 20' D. 5'
1 Exam Prep – OSHA for Business and Finance 4
9. The minimum number of toilet seats and urinals for 200 employees is _ .
A. 1 C.3
B. 2 D. 4
10. The minimum illumination of an indoor warehouse is candles.
A. 3' C. 10'
B. 5' D. 12'
11. During demolition procedures, the maximum size opening cut in a floor for the disposal of materials shall
not exceed unless lateral supports of the removed flooring remain in place.
A. 8' by 10'
B. 10% of the total aggregate floor area
C. 20' by 20'
D. 25% of the total aggregate floor area
12. An interior hung scaffold is to be suspended from the beams of a ceiling. The suspension rope wire shall be
capable of supporting times the intended load.
A. 4 C. 6
B. 5 D. 7
13. The maximum weight which can be supported by a pump jack scaffold is lbs.
A. 250 C. 1,000
B. 500 D. 2,000
14. As used in OSHA, the word "shall" means .
A. Recommended
B. Mandatory
C. Might
D. Ought to
15. A stairway or ladder shall be provided at all personnel points of access where there is a break in elevation
of or more.
A. 16" C. 25"
B. 19" D. 36"
1 Exam Prep – OSHA for Business and Finance 5
PRACTICE TEST THREE
1. The proper maintenance of a carbon dioxide fire extinguisher is to ___ .
A. Check the pressure gauge monthly.
B. Discharge it annually and then recharge.
C. Weigh semi-annually.
D. Check the pressure gauge annually.
2. A contractor agrees with a subcontractor to divide job site responsibilities such as providing safety programs,
temporary sanitation facilities, etc. Which applies?
A. Is not required
B. Illegal under OSHA rules
C. Legal: the contractor cannot be relieved of overall responsibility.
D. Legal: the subcontractor and prime contractor are held liable.
3. The contents of a first aid kit should be checked .
A. Monthly C. Bi-weekly
B. Weekly D. Semi-annually
4. A ladder, stairway, or ramp shall be located in trench excavations that are or more in depth.
A. 2' C. 6'
B. 4' D. 10'
5. When debris is dropped through an opening in the floor without the use of a chute, the area onto which the
materials are dropped shall be completely enclosed with barricades not less than in height and not less
than from the projected edge of the opening above.
A. 36" — 2' C. 42" — 4'
B. 36" — 4' D. 42" — 6'
6. All employees using abrasive wheels shall be protected .
A. With accessory body and face guards.
B. With flexible hooded, ventilated goggles.
C. By the use of momentary pressure switches.
D. By eye protection equipment.
7. During structural steel assembly, in the final placing of solid web structural members, the load shall not be
released from the hoisting line until the members are secured with bolts or the equivalent at each
connection and drawn up wrench tight.
A. All required
B. Not less than six
C. Not less than four
D. Not less than two
1 Exam Prep – OSHA for Business and Finance 6
8. Cylinders containing oxygen or acetylene shall not be ___.
A. Taken into confined spaces.
B. Refilled at the work site.
C. Stored in direct sunlight.
D. Used to troll for sharks.
9. Every open-sided floor or platform above the adjacent floor or ground level shall be guarded
by a standard railing, or equivalent, on all open sides except where there is an entrance to a ramp, stairs, or fixed
ladder.
A. 4' C. 6'
B. 5' D. 8'
10. The proper way to hang an extension cord over a hallway ceiling during construction is .
A. With wire.
B. With staples.
C. With rope.
D. Under a bent nail.
11. Fixed ladders shall be used at a pitch no greater than _ degrees from the horizontal, as measured
to the back side of the ladder.
A. 45 C. 90
B. 60 D. 120
12. The maximum variance in riser height or tread depth shall not be over in any stairway system.
A. 1/8 inch
B. 3/16 inch
C. 1/4 inch
D. 3/8 inch
1 Exam Prep – OSHA for Business and Finance 7
PRACTICE TEST FOUR
1. No combustible material shall be stored outdoors within of a building or structure.
A. 10'
B. 15'
C. 20'
D. 30'
2. When safety nets are required, the mesh size of the nets shall not exceed by .
A. 4" — 4" C. 8" — 8"
B. 6" — 6" D. 8" — 6"
3. A trench in Type B soil is 12' deep and 97' long safe means of egress are required.
A. Two C. Four
B. Three D. Five
4. Safety devices on powder-actuated tools should be checked .
A. Twice daily. C. Weekly.
B. Daily. D. Monthly.
5. The maximum daily exposure an employee can have to a sound level of 100 decibels is __.
A. 15 minutes C. 4 hours
B. 2 hours D. 8 hours
6. Overhead protective covering of 2-inch planking, plywood, or other solid material of
equivalent strength shall be provided on the top of every personnel hoist.
A. ¼” C. ½”
B. ¾” D. 5/8”
7. Handrails and top rails of guardrail systems shall be of such construction as to be capable of withstanding a
minimum load of pounds applied in any direction or point on the top rail.
A. 100 C. 200
B. 150 D. 250
8. The minimum diameter of hoisting and counterweight wire ropes when used for personnel hoists shall
be .
A. 1/4" C. 1/2"
B. 3/8" D. 5/8"
1 Exam Prep – OSHA for Business and Finance 8
9. The side rails of portable ladders shall extend a minimum of above the landing.
A. 22" C. 30"
B. 24" D. 36"
10. The factor that determines if a compressed air hose requires a pressure reduction safety device at the air
source is .
A. Length
B. Inside diameter
C. Pressure
D. The number of fittings
11. The minimum difference between work levels without protected sides or edges that require a fall protection
system is .
A. 4' C. 8'
B. 6' D. 10'
12. All rider-operated equipment used in site clearing operations shall be equipped with a rear canopy guard of
1/4-inch woven wire mesh with openings no greater than .
A. 1" C. 9/16"
B. 1/2" D. 7/8"
13. The minimum overlap for a scaffolding plank is , while maintaining a maximum overhang of
inches beyond the supports.
A. 16" — 12" C. 8" —12"
B. 12" — 12" D. 10" — 10"
14. The minimum number of hoisting ropes used for drum-type personnel hoists is .
A. Two C. Four
B. Three D. Five
1 Exam Prep – OSHA for Business and Finance 9
PRACTICE TEST FIVE
1. On a job site with a total of 275 employees, a contractor is required to have portable chemical toilets.
A. Six C. 10
B. Eight D. 12
2. All of the following face and eye equipment are approved by (OSHA) Code of Federal Regulations, for
protection from flying particles when using chipping tools except __ .
A. Flexible fitting goggles.
B. Metal-frame spectacles with side shields.
C. Plastic-frame spectacles with side shields.
D. Face shields.
3. No more than ___ gallons of flammable or combustible liquids shall be stored in a room outside of an
approved storage cabinet.
A. 10 C. 30
B. 25 D. 20
4. Material stored within a building shall not be stored within _ of a fire door opening.
A. 3 ft. C. 5 ft.
B. 2 ft. D. 1 ft.
5. When doing heavy grinding, type goggles are required.
A. 1,3,5 6, 10
B. 2, 10
C. 7, 8 (10 in combination with 4, 5, 6 in tinted lenses)
D. 1, 3 7A, 8A (for severe exposure, add 10)
6. According to OSHA, a concrete block wall without supports can be constructed high.
A. 6' C. 10'
B. 8' D. 12'
7. Employees should not be exposed to an impact noise on a job exceeding a peak sound pressure of .
A. 100 db C. 120 db
B. 140 db D. 110 db
8. Unless listed otherwise, temporary circulation-type room heaters shall have a minimum clearance on all sides
to combustible materials of .
A. 12" C. 28"
B. 22" D. 36"
1 Exam Prep – OSHA for Business and Finance 10
9. A scaffold having adjustable platform(s) so as to permit the raising or lowering of the platform is known as
a(an) _ scaffold.
A. Mason's
B. Stone setter's
C. Outrigger
D. Needle Beam
10. The maximum pole spacing for a light duty wood scaffold constructed with 2x10 planking is .
A. 7' C. 9'
B. 8' D. 10'
1 Exam Prep – OSHA for Business and Finance 11
PRACTICE TEST SIX
1. The maximum loading of a heavy-duty scaffold is ___ P.S.F.
A. 15 C. 50
B. 25 D. 75
2. Excavation support systems shall be designed by a qualified person when the excavation is in excess
of in depth, is adjacent to structures or improvements, or is subject to vibration or ground
water.
A. 5' C. 15'
B. 20' D. 18'
3. Whenever materials are dropped more than to any point lying outside the exterior walls of
the building, enclosed chute of wood or a equivalent material shall be-used.
A. 12' C. 18'
B. 15' D. 20'
4. The maximum span of 2" by 10" rough sawn lumber on a scaffold when loaded with 50 P.S.F. is .
A. 6' C. 8'
B. 7' D. 9'
5. A quick-closing valve on gas acetylene cylinders should not be open more than .
A. One-quarter of a turn.
B. One turn.
C. One and one-half turns.
D. Two turns.
6. Horse scaffolds shall not be constructed or arranged more than two tiers high or _____ in height,
whichever is less.
A. 4' C. 8'
B. 6' D. 10'
7. Scaffold platforms shall extend over their center line supports at least .
A. 2" C. 6"
B. 4" D. 12"
8. Where platforms are overlapped to create a long platform, platforms shall be secured from movement or
overlapped at least _.
A. 2" C. 6"
B. 4" D. 12"
1 Exam Prep – OSHA for Business and Finance 12
9. According to the (OSHA) Code of Federal Regulations, a trench is a narrow excavation in which the bottom
width is not greater than _.
A. 5' C. 15'
B. 10' D. 20'
10. Job-made wooden ladders with spliced side rails shall be used at an angle such that the horizontal distance
from the top support to the foot of the ladder is _ the working length of the ladder.
A. One-third
B. One-quarter
C. One-fifth
D. One-eighth
11. Toe boards shall be capable of withstanding at any point a force of at least _ pounds applied in
any downward or outward direction at any point.
A. 50 C. 175
B. 100 D. 200
12. Where oxygen deficiency or a hazardous atmosphere exists or could reasonably be expected to exist, the
atmosphere in the excavations shall be tested before employees enter excavations greater than deep.
A. 4' C. 6'
B. 5' D. 8'
13. The safe working load for a 1" shackle is _ pounds.
A. 6,400 C. 11,200
B. 8,600 D. 43,400
1 Exam Prep – OSHA for Business and Finance 13
PRACTICE TEST SEVEN
1. The common drinking cup is .
A. Prohibited in hazardous areas.
B. Prohibited in areas where more than three workmen will use the cup.
C. Not prohibited.
D. Always prohibited.
2. An out-of-order tag will be identified by a _.
A. White tag, white letters on a red square.
B. White tag, white letters on a red oval with a black square.
C. Yellow tag, yellow letters on a black background.
D. White tag, white letters on a black background.
3. A kickout .
A. Is the same as a trench jack.
B. Prevents the fall of a scaffold.
C. Relieves pressure from a tank.
D. Is an accidental release or failure of a cross brace.
4. Which of the following problems is not caused by asbestos?
A. Lung cancer
B. Gastrointestinal cancer
C. Asbestosis
D. Angina
5. Hallways of a construction project must be illuminated with a minimum of candles.
A. 5' C. 7'
B. 3' D. 10'
6. Under OSHA terms, a 'competent person' is a(n) .
A. Designated superintendent on the job site.
B. Office person who is in charge of a safety program.
C. OSHA official.
D. Person who can identify a hazard in a working area and has the authorization to correct it.
7. Where skeleton steel erection is being done, a tightly planked and substantial floor shall be maintained
within directly below and under that portion of each tier of beams on which any work is being
performed.
A. Two stories or 30 feet
B. Four stories or 48 feet
C. Two stories or 25 feet
D. Eight stories or 100 feet
1 Exam Prep – OSHA for Business and Finance 14
8. According to (OSHA) Code of Federal Regulations, a hand-held grinder with a 2-1/8" diameter wheel shall
be equipped with only a .
A. Constant pressure switch.
B. Momentary contact on/off control.
C. Positive percussion switch.
D. Positive on/off switch.
9. Temporary stairs shall have a landing not less than in the direction of travel at every 12 feet of
vertical rise.
A. 30" C. 42"
B. 36" D. 48"
10. When a stack of loose bricks reaches a height of 4 feet, the stack shall be tapered back _ _for
every foot of height above the 4-foot level.
A. 1" C. 2-1/2"
B. 2" D. 3"
11. The working clearance for an electrical switch panel that may likely require inspection live would
be if the voltage is 120.
A. 24" C. 36"
B. 30" D. 48"
12. Lifelines subjected to cutting or abrasion shall be a minimum diameter of wire core manila rope.
A. 3/4" C. 1"
B. 7/8" D. 1-1/4"
1 Exam Prep – OSHA for Business and Finance 15
PRACTICE TEST EIGHT
1. No more than gallons of combustible materials can be stored inside a regular storage area.
A. 10
B. 15
C. 20
D. 25
2. According to O.S.H.A. Health & Safety Regulations the term "Subcontractor" means:
A. Laborers and materials employed directly upon site work.
B. Person who agrees to perform any part of the labor or material requirements of contract for
construction.
C. Supplier of goods or materials in question, which are ordinarily sold to other customers from regular
Inventory.
D. Officer of a construction company.
3. Fall protection is required for an employee when working on a scaffold feet or greater.
A. 3
B. 5
C.10
D. 12
4. If you have 5 different businesses how many OSHA 300 log forms must you keep?
A. in a central location
B. one for each of the companies
C. one for each of the companies at every jobsite
D. one for each work crew
5. Floor and bench mounted grinders shall be provided with work rests which are rigidly supported and readily
adjustable. Work rests shall be kept at a distance not to exceed from the surface of the wheel.
A. 1/4"
B. 1/8"
C. 1/2"
D. 3/4"
6. For how many months is it required to keep OSHA records?
A. 12
B. 24
C. 36
D. 48
1 Exam Prep – OSHA for Business and Finance 16
7. means a person approved or assigned by the employer to perform a specific type or
duty or duties or to be at a specific locations or locations at the jobsite.
A. Approved
B. Superintendant
C. Employee
D. Authorized person
8. Oxygen deficiency, a hazardous condition, occurs when the oxygen level falls below?
A. 19.50%
B. 20%
C. 20.50%
D. 21%
9. What is the color of warning tape for underground electrical applications?
A. yellow
B. red
C. orange
D. green
10. When a death has occurred, you must notify OSHA with
A. 24 hours
B. 7 days
C. 1 year
D. 8 hours
11. You must record the following information for OSHA except
A. death
B. first aid
C. loss of consciousness
D. when CPR is used
12. Advanced notice of a Safety related inspection may not be given, except in the following situations:
A. in a case if imminent danger
B. circumstances where the inspection can most effectively be conducted after regular business hours
C. special preparations are necessary for an inspection
D. all of the above
13. What is the Minimum fine that may be administered to a contractor for an OSHA violation?
A. $7,000
B. $1,000
C. $2,500
D. $70,000
1 Exam Prep – OSHA for Business and Finance 17
14. A first aid kit must be checked at least .
A. Daily
B. weekly
C. monthly
D. bi weekly
15. Portable electrical tools do not have to be grounded if .
A. They operate at less than 75 volts
B. Less than 1/2hp
C. When used when water is not present
D. They are double insulated
16. What is the term for opening and closing a welding tank quickly?
A. cracking
B. tapping
C. popping
D. purging
17. When masonry blocks are stacked more than 6 feet high, what are the requirements?
A. tapered back one-half block per tier
B. level within 5 degrees
C. must be on a pallet
D. all of the above
1 Exam Prep – OSHA for Business and Finance 18
1 Exam Prep
Business and Finance
OSHA Practice Test Answers
ANSWERS TO PRACTICE TEST ONE
1. B 4. B 7. C 10. D 13. C
2. D 5. D 8. A 11. C 14. B
3. D 6. A 9. A 12. D
ANSWERS TO PRACTICE TEST TWO
1. B 4. B 7. B 10. B 13. B
2. B 5. A 8. A 11. D 14. B
3. A 6. A 9. D 12. C 15. B
ANSWERS TO PRACTICE TEST THREE
1. C 4. B 7. D 10. C
2. C 5. D 8. A 11. C
3. B 6 .D 9. C 12. C
ANSWERS TO PRACTICE TEST FOUR
1. A 4. B 7. C 10. B 13. B
2. B 5. B 8. C 11. B 14. A
3. A 6. B 9. D 12. A
ANSWERS TO PRACTICE TEST FIVE
1. A 2. D 3. B 4. A 5. D
6. B 7. B 8. A 9. A 10. D
ANSWERS TO PRACTICE TEST SIX
1. D 4. C 7. C 10. D 13. C
2. B 5. C 8. D 11. A
3. D 6. D 9. C 12. A
1 Exam Prep – OSHA for Business and Finance 19
ANSWERS TO PRACTICE TEST SEVEN
1. D 4. D 7. A 10. B
2. D 5. A 8. B 11. C
3. D 6. D 9. A 12. B
ANSWERS TO PRACTICE TEST EIGHT
1 D 4. A 7. A 10. D 13. D 16. A
2 B 5. A 8. A 11. B 14. B 17. A
3 C 6. D 9. C 12. D 15. D
* See below for page numbers and explanation of answers
1 Exam Prep – OSHA for Business and Finance 20
EXPLANATION OF ANSWERS
PRACTICE TEST ONE
1. Ans B. 1926.301(c) Tool Handling Subpart I:
Tools - Hand and Power.
2. Ans D. Subpart E: Personal ... Equipment. Sec
.102 - Eye protection.(3), (i), (ii)
Sec:1926.102(a)(3)
3. Ans D. Subpart P: Excavations .Sec. .651(C) (2).
Access/Egress
4. Ans B. Subpart C: General Safety and Health
Provisions Sec .28 (a). Ind: Personal protective
equipment
5. Ans. D. Sec 1926.104(b) Subpart E: Personal
Protective and Life Saving Equipment.
6. Ans A. Sec 1926.104(d) Subpart E: Personal
Protective and Life Saving Equipment. Sec
.502(d)16(iii).
7. Ans C. Subpart. F Ind: Fire Protection,
Firefighting Equipment, Sec .150 (c), Pg 243. See
(c)(i). Note: Ans A looks possible because of the
wording "each 3,000 square feet" , but also says
(major fraction
thereof". 1,500 sq ft = major fraction of 3,000 sq ft.
8. Ans A. 1926.302 Subpart I: Tools – Hand and
Power. Sec.302 - Power-operated hand tools (a).
9. Ans A.1926.200(b)(2) Subpart G: Signs, Signals,
and Barricades. Sec. 200 (b).
10.Ans D. 1926 Subpart L Appendix A. 2.b
11.Ans. C Subpart D Occupational Health an
Environmental Controls. Sec. 50 (2).
12.Ans D.Subpart H: Materials Handling, Storage,
Use and Disposal. Sec.250 (iv).
13.Ans C. 1926.302 (b)(3) Subpart I: Tools -- Hand
and Power. Sec. 302 (3).
14.Ans B. Subpart P: Excavations. Appendix B -
Table B-1, pg 319.Also see Sec. 652 (1) Option.
PRACTICE TEST TWO
1. Ans B. Subpart L: Scaffolds. Sec.452.(a) Ladder
jack scaffolds (k).
2. Ans B. Subpart L: Scaffolds. Sec. 451.(h) Falling
object protection (2) (ii).
3. Ans A. Subpart I: Tools -- Hand and Power. Sec.
300. (d) Switches (3).
4. Ans B. Subpart X: Stairways and Ladders. Sec.
1053 (3)(i).
5. Ans A. Subpart X: Stairways and Ladders.
Sec.1052 (6). N.B. There is a difference between
stair rails and hand rails
6. Ans A. Subpart F: Fire Protection. Sec. 150 (c)
(1)(i) Portable firefighting equipment. Needs
rewording: required for each 3,000 sq ft.
7. Ans B. Subpart E: Personal Protective and Life
Saving Equipment. Sec. 104 - Safety
belts, lifelines, and lanyards (d).
8. Ans A. Subpart N: Cranes, Derricks, Hoists,
Elevators, and Conveyors. Sec. 550 (15) (ii).
9. Ans a Subpart D: Occupational Health and
Environmental Controls. Sec 51
- Sanitation. (c) - Toilets at construction
jobsites., Table D-1.
10.Ans B. Subpart D: Occupational Health and
Environmental Controls. Sec. 56 - Illumination.
Table D-3.
11.Ans D. Subpart T: Demolition. Sec. 853
- Removal of materials through floor openings.
12.Ans C. Subpart L: Scaffolds. Sec. 451- General
requirements (4). Also see Suspension, Sec 452(t)
13.Ans. B. Subpart L: Scaffolds. Sec. 454 Training
requirements (j) Pump jack
scaffolds. Appendix A„ Sec 452(j)
14.Ans B. Subpart C: General Safety and Health
Provisions. Sec. 32 Definitions (q).
15.Ans B. Subpart X: Stairways and Ladders. Sec.
1051 - General requirements (a).
PRACTICE TEST THREE
1. Ans C. Subpart F: Fire Protection.Sec. 150. Table
F-1.
2. Ans C. Subpart B: General Interpretations.Rules
of constr. Sec16 (a).
3. Ans B. Subpart D: Occupational Healthand
Environmental Controls. Sec. 50 -Medical services
and first aid (2).
4. Ans B. Subpart P: Excavations. Sec. 651-
Specific excavation requirements (2).
5. Ans D. Subpart T: Demolition. Sec. 850-
Preparatory operations (h).
ALSO SUB 252 LETTER H
6. Ans D. Subpart I: Tools - Hand and Power.
1 Exam Prep – OSHA for Business and Finance 21
7. Ans D. Subpart R: Steel Erection. Sec.750, Pg
352 Sec 756„ Beams and columns. (a)(1). "solid
web structural members ...two bolts".
8. Ans. A Subpart J: Welding and Cutting. Sec. 350
Gas welding and cutting (b) Placing cylinders (4).
9.Ans C. Subpart M: Fall Protection. Sec.501 (b)(1).
10.Ans C. Subpart K: Electrical. Sec. 416 - Safety
Related Work practices (e)(2) Extension
cords...Also 405 – Wiring methods, etc. (J),
11.Ans C. Sec. Subpart X. Stairways and Ladders.
Sec. 1053. (b) Use(5)
12.Ans C. Subpart X: Stairways and Ladders. Sec.
1052 (3).
PRACTICE TEST FOUR
1. Ans A. Subpart F: Fire Protection. Sec. 151(C)
(5).
2. Ans. B. Subpart E: Personal Protective and Life
Saving Equipment. Sec. 105 Safety nets (d).
3. Ans A. Subpart P: Excavations. Sec 651 -
Specific evacuation requirements(C) (2). Means of
egress from trench evacuations. Not specific answer
and only reference I could find.
4. Ans B. Subpart I: Tools - Hand and Power. Sec.
302- Power-operated hand tools. (e) Power-actuated
tools (2).
5. Ans B. Subpart D: Occupational Health and
Environment Controls. Sec. 52, Table D-2 -
Permissible Noise Exposures.
6. Ans B. Subpart N: Cranes, Derricks, Hoists,
Elevators, and Conveyors. Sec. 552 - Material
hoists...and elevators. Overhead protection(B) (3).
7. Ans C. Subpart M: Fall Protection. Sec. 502
System criteria and practices(B) (3).
8. Ans C. Subpart N: Cranes, Derricks, Hoists, etc.
Sec. 552 - Material hoists, personal hoists, and
elevators (14) (ii).
9. Ans D. Subpart X - Stairways and Ladders. Sec
1053 - Ladders. (3)(i).
10.Ans B. Subpart I: Tools -- Hand and Power.Sec.
302 - Power... hand tools(B) (7)
11.Ans B. Subpart M: Fall Protection. Sec. 501 -
Duty to have fall protection (b)(1).
12.Ans A. Subpart 0: Motor Vehicles, Mechanized
Equipment, and Marine Operations.Sec. 604 - Site
clearing (ii).
13.Ans B. Subpart L: Scaffolds. Sec. 451 - General
requirements. (b) Scaffold platform construction -
(7) and (5)(i).
14.Ans A. Subpart N: Crane, Derricks, Hoists...Sec.
552 (14) Ropes (i).
PRACTICE TEST FIVE
1. Ans A. Subpart D: Occupational Health and
Environmental Controls. Sec. 51 - Sanitation. (c)
Toilets at construction jobsites„Table D-1. 275+ 50
= 5.5. Round up to 6 toilets.
2. Ans D. Subpart E: Personal Protective and
LifeSaving Equipment Sec .102. See Table E-1.
3. Ans. B Subpart F: Fire Protection Sec. 152-
Flammable & combustible liquids(B) Indoor
Storage of...
4. Ans A. Subpart F: Fire Protection. Sec. 151 Fire
prevention (7)(D)..
5. Ans D. Subpart E: Personal Protective and Life
Saving Equipment. Sec. 102 - Eye and
face protection. See Table E-1..
6. Ans B. Subpart Q Concrete and Masonry
Construction. Sec. 706 - Requirements for masonry
construction (b).
7. Ans. B. Subpart D: Occupational Health and
Environmental Controls. Sec. 52 - Occupational
noise exposure (e).
8. Ans A. Subpart F: Fire Protection. Sec. 154 -
Temporary heating devices (b).
Plus Table F-4.
9. Ans A. Subpart L: Scaffolds. Sec. 450. See
Mason's adjusted supported scaffold, then
Self-contained adjustable scaffold.
10.Ans D. Subpart L: Scaffolds. Sec. 454, Appendix
A, Table: Independent Wood Pole Scaffolds. See
Light Duty with 2 x 10 planking. Max pole spacing
= 10'.
PRACTICE TEST SIX
1. Ans D. Subpart L: Scaffolds. Sec. 454 Training
requirements. See table
2. Ans B. Subpart P: Excavations, Sec. 652, See
Selection of protective systems,Appendix F,
3. Ans D. Subpart H: Materials Handling, Storage,
Use, & Disposal.Sec. 252 - Disposal of waste
materials (a).
4. Ans C. Subpart L: Scaffolds. Appendix A,
Scaffold Specifications. Table.
5. Ans C. Subpart J: Welding and Cutting. Sec. 350
- Gas welding and cutting. (d) Use of fuel gas (2).
6. Ans D. Subpart L: Scaffolds. Sec .452.
Additional requirements... Horse scaffolds (f)(1)..
1 Exam Prep – OSHA for Business and Finance 22
7. Ans C. Subpart L: Scaffolds . 451, (b) Scaffold
platform constriction (4).
8. Ans D. Subpart L: Scaffoldsi (b) Scaffold
platform construction (7).
9. Ans C. Subpart P: Excavations Sec .650. Trench
definition.
10. Ans D. Subpart X: Stairways and Ladders. (b)
Use. Sec.1053 Ladders (5)(i)(ii).
11.Ans A. Subpart L: Scaffolds. Sec. 451 (h)
Falling object protection (4) (i)
12. Ans A. Subpart P: Excavations. Sec. 651 -
Specific excavation requirements.
(g) Hazardous atmospheres (i).
13. Ans C. Subpart H: Materials Handling, Storage,
Use, and Disposal. Sec. 251. Table H-19, Safe
Working Loads for Shackles.
PRACTICE TEST SEVEN
1. Ans D. Subpart D Occupational Healths. Sec..51
Sanitation.(A) (4).
2. Ans D. Subpart G: Signs, Signals, & Barricades.
Sec..200. Table G-1.
3. Ans D. Subpart P: Excavations Sec. 650.
Definition kickout
4. Ans D. Subpart Z: Toxic & Hazardous Appendix
H. II Health Hazard Data
5. Ans A. Subpart D: Occupational Health and
Environmental Controls. Sec. 56 - Illumination.
Table D-3.
6. Ans D. Subpart C: General Safety Sec. 32.
Definitions (f)
7. Ans. A. Subpart R Steel Erection. Sec.760 Fall
Protection, pg 3354, (b)(1). Sec. 754
8. Ans. B. Subpart I: Tools -- Hand and owlet Sec.
300 General requirements (d) Switches (2).
9. Ans A. Subpart X: Stairways and Ladders Sec.
1052 Stairways (1).
10.Ans B. Subpart H: Materials Handling... Sec.
250 (6).
11.Ans C. Subpart K: Electrical. Sec. 403 Table K-
1.
12.Ans B. Subpart E: Personal Protective and Life
Saving Equipment. Sec .104 – Safety belts,
lifelines, and lanyards (c).
PRACTICE TEST EIGHT
No explanations
Top Related