Cleanwater Blue Quick-Start Guide1. Clean Tub & New or Clean Filter(s)
Fill spa with fresh water. After full, jets must be on to circulate the water while adding chemicals to effectively distribute throughout entire tub.
2. Fill spa and circulate water with jets
3-WAYTEST
STRIPS
25TEST
STRIPS
CLE
AN
WA
TER
3. Test water
4. Shock water with Oxy-Spa
CLE
AN
WA
TER
Calc
ium
Seq
uest
rant
for R
esid
entia
l Spa
s an
d Ho
t Tub
sDA
NG
ER: K
EEP
OUT
OF
REAC
H O
F C
HIL
DRE
N.
NET
CONE
NTS:
8 F
L. O
ZS (2
37 M
L)
5. Add Cleanwater Prep™
6. Rinse Filter(s) of calcium deposits
CLEA
NW
AT
ERA
lgicide/Bactericide for S
pas and Hot Tubs
DAN
GER: KEEP O
UT OF REAC
H O
F CH
ILDREN
.NET CONENTS: 8 FL. OZS (237 M
L)ACTIVE INGREDIENTSCopper Suflate Pentahydrate...... 19.8%*Inert Ingredients........................ 80.2%TOTAL.........................................100%
7. Add Cleanwater Blue™ & clarifier
8. Place ZorbO in spa
3-WAYTEST
STRIPS
25TEST
STRIPS
CLE
AN
WA
TER
9. After and every 2 weeks, retest
CLEAN
WATER
Scale & M
etal Inhibitor for Spas and Hot Tubs
DANGER: KEEP OUT OF REACH
OF CHILDREN
.NET CONENTS: 8 FL. OZS (237 M
L)
10. After and every 2 weeks, add Cleanwater Purge™
Start with an empty, clean tub and new or clean filter cartridge(s). (Use Spa System Flush when transitioning from any previous sanitizer system.)
Total Alkalinity (TA): 30 - 90 ppm pH: 7.2 - 7.6
Test water with Cleanwater Blue™ 3-Way Test Strips. Adjust TA and/or pH if necessary. Ignore copper reading for now.
Shock water by adding 1 tablespoon non-chlorine MPS Oxy-Spa per 150 gallons of spa water.(OPTIONAL - instead of Oxy-Spa, add 1 teaspoon dichlor granules per 250 gallons.)
Add 10 milliliters Cleanwater Prep™ per 100 gallons of spa water. Run filtration cycle for 2 - 4 hours or overnight (while spa is heating) before proceeding. Excess calcium will be removed and deposited onto the filter. Cleanwater Prep is only added at startup or refill.
Rinse filter cartridge(s) to remove any calcium deposits collected.
After rinsing, replace filter and add 6 milliliters of Cleanwater Blue™ per 100 gallons of spa water. Add 2 tablespoons of natural clarifier per 500 gallons of spa water.
Place and keep ZorbO in spa to absorb oil scum.Rinse out every 1 - 2 weeks and replace every 3 - 6 months.After each spa use, add 1 - 2 teaspoons Oxy-Spa.
After and every 2 weeks, test water balance; adjust TA and pH if necessary. If copper is within range, DO NOT ADD MORE Cleanwater Blue!
Wait to add Cleanwater Purge™ until after 2 weeks of spa circulating with Cleanwater Blue.Add 5 milliliters Cleanwater Purge™ per 100 gallons of spa water, every 2 weeks.
(800) 823-3638Mon-Fri 6 AM - 5 PM PSTFor more information see instructions inside Cleanwater Blue box.
Copper: 0.5 - 1.0 ppm
My spa is __________ gallons.DO NOT GUESS, See insert in Cleanwater Blue box to determine gallons.
I need __________ tablespoons of Oxy-Spa at startup.
I need __________ ml of Cleanwater Prep at startup.
I need __________ ml of Cleanwater Blue, and ________ tablespoons clarifier at startup.
I need __________ ml of Cleanwater Purge every two weeks.
Top Related