Z8F04328100KIT Development Kit User Manual Sheets/ZiLOG PDFs... · · 2005-02-04Z8F04328100KIT...

ZiLOG WorTelephon

Z8 Encore® 4K Series Microcontrollers

Z8F04328100KIT Development Kit
User Manual UM018501-1004
PRELIMINARY

ldwide Headquarters • 532 Race Street • San Jose, CA 95126e: 408.558.8500 • Fax: 408.558.8300 • www.ZiLOG.com

http://www.ZiLOG.com

Z8F04328100KIT Development KitUser Manual

PRELIMINARY UM018501-1004

ii

This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to request copies of publications, contact:

ZiLOG Worldwide Headquarters532 Race StreetSan Jose, CA 95126Telephone: 408.558.8500Fax: 408.558.8300www.ZiLOG.com

Document DisclaimerZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service names mentioned herein may be trademarks of the companies with which they are associated.©2004 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Devices sold by ZiLOG, Inc. are covered by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose Except with the express written approval of ZiLOG, use of information, devices, or technology as critical components of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this document under any intellectual property rights.


iii

Table of ContentsTable of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

List of Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

System/Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Supported Host System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Z8 Encore! 4K Series Development Board . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8UART with IrDA Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . .10External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Customer Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

UM018501-1004 PRELIMINARY Table of Contents


iv

Table of Contents PRELIMINARY UM018501-1004


v

List of FiguresFigure 1. Z8 Encore! 4K Series Development Kit Contents . . . . . . . .2

Figure 2. Z8 Encore! 4K Series Development Board . . . . . . . . . . . . .7

UM018501-1004 PRELIMINARY List of Figures


vi

List of Figures PRELIMINARY UM018501-1004


1

IntroductionThe Z8 Encore!® 4K Series MCU is the part of the line of ZiLOG micro-controller products.

The Z8 Encore! 4K Series Development Kit (Z8F04328100KIT) enables users to become familiar with the hardware and software tools available with this product. This kit consists of the 4KB version of the Z8 Encore! Development board that supports and presents the features of the Z8 Encore! 4K Series MCU. This kit allows users to begin writing applica-tion software and contains all supporting documents.

This manual acquaints users with the Z8 Encore! 4K Series Development Kit, and gives instructions on setting up and using the tools to start build-ing designs and applications.

Kit ContentsThe Z8 Encore! 4K Series Development Kit contains the following:

Hardware• Z8 Encore! 4K Series Development board

• Smart Cable for PC to Z8 Encore! 4K Series Development board (DB9 to six-pin male)

• 5VDC power supply

UM018501-1004 PRELIMINARY Introduction


2

Figure 1. Z8 Encore! 4K Series Development Kit Contents

Software (on CD-ROM)• ZDS II- Z8 Encore!® IDE with ANSI C-Compiler

• Sample code

• Document browser

• Acrobat Reader install program

Documentation• Quick Start Guide

• Registration card

• Z8 Encore! 4K Series technical documentation (on CD-ROM)

DevelopmentBoard

Packaging

CD-ROM ContainingDocumentation

PowerSupply

Smart Cable

Introduction PRELIMINARY UM018501-1004


3

– Development Kit User Manual– ZDS II - IDE User Manual– eZ8 CPU User Manual– Application notes

The sample code is installed with ZDS II and resides in the <installa-tion directory>\samples in the user's disk drive.

The documentation can be installed by the user with the DemoShield interface or can be viewed on the CD-ROM using the DemoShield menus and a PDF reader. A copy of the Acrobat installer is provided on the CD-ROM and can be installed from the DemoShield install screen. After installing the documentation on the user’s system Windows Explorer can be used to select any document to be viewed with your favorite PDF file viewer.

System/Software RequirementsIBM PC (or compatible computer) with the following minimum configu-rations:

Supported Host System Configuration• Win98 Second Edition, WinNT 4.0 Service Pack 6, Win2000 Service

Pack 3, WinXP Professional Service Pack 1

• PentiumII/233MHz processor or higher up to Pentium IV, 2.8 GHz

• 96 MB RAM or more

• 25 MB hard disk space or more

• Super VGA video adapter

• CD-ROM

• One or more RS-232 communication ports

UM018501-1004 PRELIMINARY Introduction


4

Introduction PRELIMINARY UM018501-1004


5

InstallationFollow the directions in the Quick Start Guide for software installation and setup of the Z8 Encore! 4K Series Development kit.

UM018501-1004 PRELIMINARY Installation


6

Installation PRELIMINARY UM018501-1004


7

Z8 Encore! 4K Series Development BoardIntroduction

The Z8 Encore! 4K Series Development board is a development and pro-totyping board for the Z8 Encore! 4K Series MCU. The board provides customers with a tool to evaluate features of Z8 Encore! 4K Series MCU, and to start developing an application before building the hardware.

Figure 14. Z8 Encore! 4K Series Development Board

UM018501-1004 PRELIMINARY Z8 Encore! 4K Series Development


8

Features• Z8 Encore!® MCU (28-pin SOIC)

• 3 LEDs

• RS-232 interface

• IrDA transceiver

• Two pushbuttons, RESET and TEST

• 5 VDC power connector

• On-Chip Debugger interface

• Header for ADC input

• Prototyping area

• External interface connectors JP1 and JP2

• 2.7–3.6 V operating voltage with 5V-tolerant inputs

MCUThe Z8 Encore! 4K Series MCU is member of a family of ZiLOG micro-controller products based upon the 8-bit eZ8 core CPU. The Flash in-cir-cuit programming capability allows for faster development time and program changes in the field. The eZ8 core CPU is upward compatible with existing Z8® instructions. The rich peripheral set of the Z8 Encore! 4K Series makes it suitable for a variety of applications including motor control, security systems, home appliances, personal electronic devices, and sensors.

The Development board contains circuitry to support and present all the features of the Z8 Encore! 4K Series. The main features of the Z8 Encore! 4K Series are:

Z8 Encore! 4K Series Development BoardPRELIMINARY UM018501-1004


9

• eZ8 core CPU

• 4KB Flash memory with in-circuit programming capability

• 1KB register RAM

• 5-channel, 10-bit analog-to-digital converter (ADC)

• Full-duplex UART

• I2C interface (Master Mode only)

• Serial Peripheral Interface (SPI)

• Infrared Data Association (IrDA)-compliant infrared encoder/decoder

• Two 16-bit timers with capture, compare, and PWM capability

• Watch-Dog Timer (WDT) with internal RC oscillator

• Eleven (20-pin package) or nineteen (28-pin package) I/O pins

• Programmable priority interrupts

• On-Chip Debugger

• Voltage Brown-out Protection (VBO)

• Power-On Reset (POR)

• 2.7–3.6 V operating voltage with 5V-tolerant inputs

• Operating temperatures: 20° ±10° C

For further information on the Z8 Encore!® family of devices, consult the product specification, P/N PS0197, available for download from www.zilog.com.

UART with IrDA EndecThe Z8 Encore! 4K Series (component U5)contains a fully-functional, high-performance UART with Infrared Encoder/Decoder (ENDEC). The Infrared Endec is integrated with an on-chip UART allowing easy com-

UM018501-1004 PRELIMINARY Z8 Encore! 4K Series Development


10

munication between the Z8 Encore!® 4K Series and IrDA transceivers. Infrared communication provides secure, reliable, low-cost, point-to-point communication between PCs, PDAs, cell phones, printers and other infrared enabled devices.

Power and Communication InterfacesTable 1 provides jumper information concerning the shunt status, func-tions, devices and defaults affected of jumpers JP3 and JP4.

External Interface Headers JP1 and JP2External interface headers JP1 and JP2 are shown in the schematic on page 11.

Table 1. Jumpers JP3 and JP4

Jumper StatusDevice Affected Status Default

JP3* OUT RS-232 interface

Enabled X

JP3 IN RS-232 interface

Disabled

JP4* OUT IrDA interface EnabledJP4 IN IrDA interface Disabled XJP5 OUT U5 RESET/

PD0PD0 (GPIO) X

JP5 IN U5 RESET/PD0

RESET when SW1 pressed

Note: * These jumpers must not be OUT at the same time

Z8 Encore! 4K Series Development BoardPRELIMINARY UM018501-1004

Schematics

Z8F04328100KIT Development Kit User Manual

11

1

1

D

C

B

A

connector 1forreferenceonly

dule is plugged onto the Dev Platform the local

interface is disabled by pin 50 of JP2

96C0941-001 B

4K MDS Processor Module. Schematic.

1 2ednesday, February 25, 2004

ment Number Rev

Sheet of

A20

-CS0

A12

-IOREQ

-F91_WE

A13

GND

GND

A17

A21

VCC_33V

A14

D1

VCC_33V

D7

-DIS_FLASH

GNDA6 A0

D3

D6

-BUSACK

A3

D2

VCC_33V

A15

A4

-TRSTN

D0

-MREQ

A7

A10

A9

A16A18

A11

-INSTRD

A19

A5

GNDD5

-CS1A22

A1A2

-CS2

-RD

A8GND

D4

A23

-WR-BUSREQ

GND

7

3_CTS0

7

VCC_33V

4

7_T1OUT PA2PA1_T0OUTGND

GND

PC5

4_RXD0 PA5_TXD0

GND

GND6

PA0_T0IN

PC6

GNDC_33V

-DIS_IrDA

4_ANA7 PC2_ANA6PC0_ANA4PB2_ANA2PB0_ANA0

1_ANA53_ANA31_ANA1

PB53_COUT

PD0

6_nT1OUT

SETVCC_33V

-DIS_IRDA-DIS_232

JP2

HEADER 30x2/SM

24681012141618202224262830323436384042444648505254565860

13579

11131517192123252729313335373941434547495153555759

JP1

HEADER 30x2/SM

24681012141618202224262830323436384042444648505254565860

13579

11131517192123252729313335373941434547495153555759

UM018501-1004 PRELIMINARY

SchematicsThe following diagrams provide schematics for the Z8 Encore! 4K Series Development Board.

Schematic, Z8 Encore! 4K Series Development Board, Page 1 of 2

5

5

4

4

3

3

2

2

D

C

B

A

connector 2

If Mo

RS232

TEST

20 pin footprint28 pin footprint

RESET/TEST2

Note 1:PB6 and PB7 are dual function pins (GPIO or AnalogSupply)R12, R13, R16, and R17 are zero-ohm jumpers used inconjuntion with GPIO Control Registers to selectfunction desired. The development board is shippedwith jumpers configured for Analog Supply.U8 is an optional filter that can be used to improvethe quality of the Analog SupplyTable 1 shows the configurations recommended

NOTE 1:

NOTE 1:

NOTE 2

Note 2: The XP supports internal, external crystal, externalceramic resonator, external R/C and external CMOS drive clock modes. R14, R15, R18, C19, C20 and Y1 are used to supportthe clock mode selected. The development board is shippedconfigured for external 8Mhz ceramic resonator or internalclock operation.Table 2 shows the recommended clock mode configurations.

Clock Mode R14 R15 R18 C19 C20 Y1

Internal Only none none none none none none

Crystal 0 Ohm 220 Ohm none Yes Yes Yes

Ceramic Res 0 Ohm 0 Ohm none none none Yes

External CMOS none none none none none none

Analog 0 ohm none 0 ohm none optional

GPIO none 0 ohm none 0 ohm none

Supply

R12 R13 R16 R17 U8

TABLE 1

TABLE 2

(Use PA0_T0INpin on JP2)

XP

B

W

Title

Size Docu

Date:

PB0_ANA0 PB2_ANA2

VCC_33V

PB3_ANA3

GND

PB1_ANA1

PB3_ANA3

PB0_ANA0

PB4_ANA7

PB2_ANA2

PB

PA

PCPC

PA

PA

PB

PA6_nT1OUT

PA7_T1OUTVC

GND

PB1_ANA1

PA2

VCC_33V

GND

PA5_TXD0

PB1_ANA1 PB0_ANA0

DBG

PA3_CTS0PA4_RXD0

PB2_ANA2PB3_ANA3

PA0_T0IN

PC3_COUT

PA7_T1OUT

PC3_COUTPC2_ANA6PC1_ANA5PC0_ANA4

PD0

PA6_nT1OUT

PC2_ANA6 PB4_ANA7

PC0_ANA4PC1_ANA5PC2_ANA6

PB6

PB7GND

PC5

PB2_ANA2

PA2

PC0_ANA4

PC2_ANA6

PA5_TXD0

PD0

PC3_COUT

PC1_ANA5

PA4_RXD0 PC4

VCC_33V

PB5

PC7

PA2

PA6_nT1OUT

PA1_T0OUT

PC6

PA3_CTS0

GND

PC1_ANA5

PA7_T1OUT

PB0_ANA0

GND

PA1_T0OUT

PB1_ANA1

PA0_T0IN

PB4_ANA7

PC0_ANA4

PB3_ANA3

DBG

PBPCPBPB

PC

GND

VCC_33V

VCC_33V

PA

-RE

GND

VCC_33V

DBG

PA3_CTS0PA4_RXD0PA5_TXD0

SENSE

D2

GREEN

21

R140

C150.001uF

SW2

SW1

R13

0

R11

100

R8

100

C20

R150

C10

0.001uF

C160.001uF

R9

100K

R16 0

U6

Z8F04xA

2

1098

3

65

201

171615

131211

147

4

1918

PB2/ANA2

PA4/RXD0PA3/CTS0PA2/DE

PB3/CLKIN/ANA3

PA1/T0OUT/XOUTPA0/T0IN/T0OUT/XIN/

PB0/ANA0PB1/ANA1

PC1ANA5/CINN/LEDPC0/ANA4/CINP/LED

DBG

PA7/T1OUTPA6/T1IN/T1OUT

PA5/TXD0

RESET/PD0GND

VDD

PC3/COUT/LEDPC2/ANA6/LED

D3

YELL

21

R10

10

C120.001uF

Y1

8 MHz

1

2

31

2

3

U8

EMI Filter

1

2

3IO

GN

D IO

C110.001uF

J2

HEADER 8X2

246810121416

13579

111315

R17 0

JP5

HEADER 2

12

R18

1M

C130.001uF

D4

RED

21

C19

R19 10K

C140.001uF

R12

0

U5

Z8F04xA_28

9

161514

1312

4

76

2827

242526

23

1

1920

11

32

1817

10

8

5

2122

GND

PC4/LEDPA6/T1IN/T1OUTPA5/TXD0

PA4/RXD0PA3/CTS0

PB3/ANA3/CLKIN

PA0/T0IN/T0OUTXINVDD

PB1/ANA1PB0/ANA0

PC1/ANA5/CINN/LEDPC2/ANA6/LEDPC3/COUT/LED

PC0/ANA4/CINP/LED

PB2/ANA2

PC6/LEDPC7/LED

PA2/DE

PB5/VrefPB4/ANA7

PA7/T1OUTPC5/LED

PB7(AGND)

PA1/T0OUT/XOUT

PB6(AVDD)

RESET/PD0DBG

R7

100

C170.001uF

C180.001uF

Z8F0423

Z8F0423

Note 2: The 4K does not support an external oscillator even though crystal Y1 is installed.

Schematics

Z8F04328100KIT Development Kit User Manual

121

1

D

C

B

A

CONSOLE

USER

96C0941-001 B

K MDS Processor Module. Schematic.

2 2nday, March 01, 2004

ent Number Rev

Sheet of

TXD0CTS0RXD0

PA4_RXD0

PA5_TXD0

IRDA_SD

GND

R3

68

C10.1uF

C9

330nFR4

2R7

C50.1uF

U4

ZHX1810

2

4

3

1

5

6

0

TXD

SD

RXD

LEDA

VCC

GND T

P1

DB9 Female

594837261

UM018501-1004 PRELIMINARY

Schematic, Z8 Encore! 4K Series Development Board, Page 2 of 2

5

5

4

4

3

3

2

2

D

C

B

A

GND

DBGINTERFACE

DIS RS232

DIS IRDA

3.3 OK

XP 4

B

Mo

Title

Size Docum

Date:

GND

VCC_33VDBG

GND

PA3_CTS0

VCC_33V

GND

VCC_33V

PA5_TXD0

VCC_33V

PA4_RXD0

GND

VCC_33V

GND

-Z_RST

GND

5V

VCC_33V

VCC

GND

-Z_RST

PA3_CTS0

DBG

-DIS_IRDA

-DIS_232

PA5_TXD0

PA4_RXD0

VCC_33V

GND

SENSE

C20.1uF

U3E

74LVC04/SO

11 10

147

C40.1uF

U3A

74LVC04/SO

1 2

147

U7

LT1129-3.3/DD

1

2

3

4

5 OUT

SENSE

GN

D

SHDN

VIN

C60.1uF

JP3

12

U3D

74LVC04/SO

9 8

147

P2

Header 3x2

1 23 45 6

R210K

U3B

74LVC04/SO

3 4

147

U3F

74LVC04/SO

13 12

147

JP4

12

R1

680

F1

RXE050

J1

PWR JACK

231

+C7

100/10C8

0.1uF

R510K

+ C3

100/10

U3C

74LVC04/SO

5 6

147

U1

MAX3222

1

2

4

5

6

13

12

15

10

3

7

17

8

16

9

20

1918

1114

EN

C1+

C1-

C2+

C2-

T1IN

T2IN

R1OUT

R2OUT

V+

V-

T1OUT

T2OUT

R1IN

R2IN

SHDN

VC

CG

ND

NCNC

TP1

1 2 3 4 5

D1

LED

21

R610K

TP2

1 2 3 4 5


13

Customer FeedbackIf you note any inaccuracies while reading this User Manual, please copy and complete this form, then mail or fax it to ZiLOG (see Return Information, below). We also welcome your suggestions!Product Information

Customer Information

Return InformationZiLOG System Test/Customer Support 532 Race Street San Jose, CA 95126 Fax: (408) 558-8536 ZiLOG Customer SupportProblem Description or SuggestionProvide a complete description of the problem or your suggestion. If you are reporting a specific problem, include all steps leading up to the occurrence of the problem. Attach additional pages as necessary.

Z8F04328100KIT Development KitSerial # or Board Fab #/Rev. #Software VersionDocument NumberHost Computer Description/Type

Name CountryCompany PhoneAddress FaxCity/State/Zip E-Mail

UM018501-1004 PRELIMINARY Customer Feedback

http://register.zilog.com/login.asp?login=servicelogin


14

Customer Feedback PRELIMINARY UM018501-1004

Z8F04328100KIT Development Kit User Manual Sheets/ZiLOG PDFs... · · 2005-02-04Z8F04328100KIT...

Documents

Transcript of Z8F04328100KIT Development Kit User Manual Sheets/ZiLOG PDFs... · · 2005-02-04Z8F04328100KIT...