YSX45E All Electric Yard Crane Spreader - Bromma · PDF file · 2017-01-032 We...
Transcript of YSX45E All Electric Yard Crane Spreader - Bromma · PDF file · 2017-01-032 We...
A Tradition of Innovation
www.bromma.com We reserve the right to change the design and technical data without prior notice.© 2015 Bromma – All rights reserved.
PI- YSX45E - en, Rev 05, November 2015
Product InformatIon
YSX45E All Electric Yard Crane Spreader
Bromma telescopic spreader YSX45E for yard cranes is an
all-electric mid-range spreader with a mechanical structure
calculated for two million cycles. The spreader is as standard
equipped with 4 x 10 metric tons lifting lugs in the corners
of the end beams for heavy lifts and for handling damaged
containers.
The spreader consists of a rectangular frame construction
enabling easy location on containers. The spreader can adjust
its length to lift 20ft, 30ft (option), 40ft and 45ft containers
using ISO floating twistlocks.
The all-electric spreader reduces power consumption to ap-
proximately 1/10 of a hydraulic spreader. The electrical motors
only consume electricity when an operation is performed.
The electrical equipment and the cable chain system are well
protected in the main frame.
All motions of the spreader are controlled from the driver’s
cab and there are provisions made for signals in the cab
indicating the position of the twistlocks and landing pin
status.
Made of high quality European steel, the YSX45E spreader
provides high lifting capacity with a low nominal tare weight
thanks to the box design of the telescoping arms and the
main frame. It is designed in accordance to EN 13001. All
components can be easily assembled, adjusted, removed and
are accessible for inspection and maintenance.
YSX45E is a silent alternative for most applications, parti-
cularly in environmentally sensitive terminals. Removing the
hydraulics also reduces the risk of hydraulic leakage in the
terminal.
The spreader can be equipped with the SCS4 Spreader Control
System, reducing and preventing downtime through impro-
vements in the area of electrical connections. It will also
shorten downtime through faster spreader fault diagnostics.
major features 90% reduction of power consumption (compared to a
hydraulic spreader) High reliability with all-electric function Stops accurately in all positions Silent and environmental friendly
Durable and strong despite low weight Easy to maintain and long service intervals Fulfils design criteria for EN 13001, DIN 15018 H2B4,
FEM 1.001 and British Standard BS 2573
The spreader shown is customized with extra equipmentLoad combinations with YSX45E20’ 30’ 40’ 45’
2www.bromma.com We reserve the right to change the design and technical data without prior notice.
© 2015 Bromma – All rights reserved. PI- YSX45E - en, Rev 05, November 2015
Proximity switch for locked position
Proximity switch for unlocked position
Proximity switch for unlocked position
Proximity switch for locked position
Helical-worm geared motor
Draw bars
Twistlock
Landing pin
Blocking stop
Twistlock arm
Proximity switch for landing pin
Blocking key
The telescoping system is driven by means of an electric mo-
tor and a purpose designed reduction gearbox connected to an
endless chain. The motor/gearbox is equipped with a friction
clutch protecting against excessive outer forces.
The spreader is latched onto containers by electrically operat-
ed floating ISO twistlocks. The twistlocks are operated in pairs
by a fixed linkage and switches are used for locking, unlock-
ing and landing pin functions.
The endless chain is fitted with a Bromma design shock ab-
sorber at both ends. The shock absorber is designed to damp-
en the effects of impact on the spreader structure and compo-
nents due to loads imposed to the spreader ends.
The telescoping system’s ability of absorbing extreme loads me-
chanically provides the end user with a highly reliable spreader
with increased life even under extreme load conditions.
The flexibility in the system allows for changes in spreader
length up to ±15 mm when handling distorted containers.
This system is durable, strong and has low weight; is easy to
maintain and has long service intervals. The telescoping posi-
tions are controlled by proximity sensors (an absolute encoder
placed on the pedestal bearing is available as an option when
SCS4 is used).
The twistlock motor is of compact and robust design with
built in mechanical stop. The floating range is ±6 mm in all
directions. Each twistlock will incorporate a mechanical inter-
lock to prohibit unlock operation when under load. The twist-
lock pins are proof load tested to 40 metric ton.
LED-type signal lights are placed on each end of the spread-
er’s main frame (optional), showing the driver when:
a) the twistlocks are open,
b) the spreader is properly engaged in the corner castings,
c) all twistlocks are properly locked in the corner castings. Corresponding signals are provided to the crane cabin.
Tension rod
Tension rod
Electric motor/gearbox
Endless chain
Shock absorber
Pedestal bearing
twIstlock system
telescoPIng system
3www.bromma.com We reserve the right to change the design and technical data without prior notice.
© 2015 Bromma – All rights reserved. PI- YSX45E - en, Rev 05, November 2015
This enhances the possibility of monitoring each I/O point
and reduces the number of cables needed and the replacement
time for connecting sensors and actuators to the controls.
CANopen box
For reliability reasons Bromma recommends the use of 24 V DC
on all controls.
The electrical safety features to protect and ensure proper
handling of containers are as follows:
Spreader cannot be hoisted unless all four twistlocks are
fully ”Locked” or ”Unlocked” (provided the crane controls
have a hoist permit safety circuit.)
Spreader twistlocks can only be ”Locked” or ”Unlocked”
when all four corners are properly seated on a container or
hatch cover.
guIde arms
The spreader is equipped with four fixed guide arms to guide
the spreader onto the container. These are located one at
each end of the long side of the spreader. The guide arms are
fastened by means of bolts and nuts and a bar that fits to a
slot in the end beam. The bar prevents the bolts from shear-
ing off in case of heavy landings. Several guide arm combina-
tions are available.
The main electric cabinet is mounted on heavy-duty rubber
shock absorbers and is well protected on or within the main-
frame. The actual position depends on the head block design.
Junction boxes are placed at the end beams. Proximity switch-
es control the positioning of the telescoping (an absolute en-
coder placed on the pedestal bearing is available as an option
when SCS4 is used).
The electrical components are mounted in a stainless steel
cabinet, IP66. All cables are well-protected in cable chains.
The power required to operate the spreader’s electrical compo-
nents is obtained from the crane. All electrical components on
the spreader are designed to withstand loads imposed during
container handling operations and suitable for a marine envi-
ronment.
The spreader can optionally be equipped with CANopen slave
units.
electrIcal system
4www.bromma.com We reserve the right to change the design and technical data without prior notice.
© 2015 Bromma – All rights reserved. PI- YSX45E - en, Rev 05, November 2015
monItorIng and dIagnostIc system scs4
For monitoring and diagnosing, the YSX45E can be equipped
with the SCS4 Spreader Control System (option). The SCS4 can
communicate with host controllers by a wide variety of proto-
cols.
The rugged SCS4 control unit is equipped with a bright touch
screen and mounted on the spreader for easy access. Monitor-
ing and diagnostics can be available in different ways; on the
screen, on the crane, through a web interface via an external
PC, a handheld computer or via Bromma Greenzone applica-
tions.
The SCS4 system delivers advanced monitoring and diagnostic
information, which means that service staff can react faster to
fault events. Instead of investigating possible sources of fault
events one by one, the SCS4 gives service technicians specific,
precise information, enabling them to quickly solve the prob-
lems occurred.
The SCS4 system simplifies handling of the spreader and pre-
vents fault events. It also eliminates or minimizes junction
boxes, terminal strips and relays- areas where wire breakage
is common. Other than that, conventional wiring is also re-
duced.
The SCS4 user interface is intuitive and easy to use. The sys-
tem also includes complete manuals for the spreader. The
backup memory and battery are placed outside the unit and
are easy to replace.
5www.bromma.com We reserve the right to change the design and technical data without prior notice.
© 2015 Bromma – All rights reserved. PI- YSX45E - en, Rev 05, November 2015
dImensIonal drawIngs – ysX45e
(only for -YSX45E
We reserve the right to change the design and technical data without prior notice.© 2015 Bromma – All rights reserved.
PI- YSX45E - en, Rev 05, November 2015
For nearest contact and latest information on Bromma products and services, visit the Bromma website at www.bromma.com
technIcal data ysX45e
Lifting capacity: (According to EN 13001, HC2, HD1, U7, Q3)
41 metric tons evenly loaded
41 metric tons ±10% eccentric loading
Lifting lugs 4 x 10 metric tons in end beams
Hoisting speed: Max 1 m/s
Weight: About 6.4 metric tons (without extra equipment)
Dimensions: See dimensional drawing (previous page)
Telescopic motion: From 20ft to 45ft in approximately 30 seconds
Twistlock rotation: 90° in approximately 1 second
Power supply: 400/230 VAC 50 Hz or otherwise as agreed
Max power consumption: 0–3.0 kW
Control system: Relay (SCS4 available as an option)
Control voltage: 24 V DC
Installed power: Telescopic system 3.0 kW
Twistlock system 2 x 0.37 kW
Total on spreader 4.5 kW
Electrical cabinet: Stainless Steel IP66
Surface conditioning: Sand-blasted SA 2.5
EPZn(R) zinc epoxy primer 50-90 µm
EP epoxy can be MIO pigmented 100 µm
PUR polyurethane 70 µm
Total: 220 µm
Design criteria: EN 13001; DIN 15018 H2B4; FEM 1.001; British Standard BS 2573
Manuals: Full service and repair manual supplied
Warranty: 1 year