YDRAFORCE Electro-Proportional Valves · 2.000.1 ®HYDRAFORCE Electro-Proportional Valves •...

2.000.1

Electro-Proportional ValvesHYDRAFORCE®

• Cartridges are voltage interchangeable.

• Water/Weather resistant coils are availablefor most valves.

• Manual override available on most models.

• Industry common cavities—compact sizes.

• Cartridges are voltage interchangeable.

• Wide variety of voltage and connector options.

• Coils are rated for continuous duty operation.

• Excellent linearity and hysteresis characteristics.

HydraForce manufactures a comprehensive line of electro-proportional pressure, flow and directional valves. Aproportional valve varies its output in response to avariable electric input.

Flow control valves (PV series) control the flow into or outof a hydraulic cylinder or motor, thereby regulating thespeed of movement.

Pressure control valves (TS series) regulate the pressureapplied to a hydraulic cylinder or motor. This regulates thetorque of the motor, or the pressure or force that thecylinder applies to its load.

Directional control valves (SP series) determine whetherthe cylinder extends or retracts, or if the motor turnsclockwise or counterclockwise.

ELECTRO-PROPORTIONAL VALVES

Recommended Electronic Controllers

2.001.1

RECOMMENDED ELECTRONIC CONTROLLERS FOR HYDRAFORCE PROPORTIONAL VALVES

EHPR08-33 2.970.1 Table 2EHPR98-T33 2.971.1 Table 2PV08-30 2.370.1 Table 1PV08-31 2.380.1 Table 1PV42-M30 2.378.1 Table 1PV70-30 2.372.1 Table 1PV70-31 2.382.1 Table 1PV70-33 2.400.1 Table 1PV70-34 2.412.1 Table 1PV70-35 2.432.1 Table 1PV72-20 2.330.1 Table 1PV72-21 2.340.1 Table 1PV72-30 2.374.1 Table 1PV72-31 2.384.1 Table 1PV72-33 2.406.1 Table 1PV72-34 2.414.1 Table 1PV72-35 2.434.1 Table 1PV76-30A 2.376.1 Table 1PV76-31 2.386.1 Table 1

SP08-20 2.008.1 Table 1SP08-21 2.020.1 Table 1SP08-22 2.024.1 Table 1SP08-25 2.028.1 Table 1SP08-41 2.078.1 Table 1SP08-46R 2.088.1 Table 1SP08-47C 2.110.1 Table 3SP08-47CL 2.111.1 Table 3SP08-47D 2.120.1 Table 3SP08-47DL 2.121.1 Table 3SP10-20 2.010.1 Table 1SP10-46R 2.090.1 Table 1SP10-41 2.080.1 Table 1SP10-47C 2.112.1 Table 3SP10-47D 2.122.1 Table 3SP10-57D 2.136.1 Table 3SP10-58D 2.146.1 Table 3SP12-20 2.012.1 Table 1TS08-20 2.812.1 Table 2TS08-27 2.860.1 Table 2

TS10-26 2.852.1 Table 2TS10-27 2.862.1 Table 2TS10-36 2.900.1 Table 2TS12-26 2.854.1 Table 2TS12-27 2.864.1 Table 2TS12-36 2.901.1 Table 2TS38-20 2.813.1 Table 2TS38-21 2.823.1 Table 2TS80-30 2.872.1 Table 2TS98-30 2.882.1 Table 2TS98-31 2.890.1 Table 2TS98-T34 2.950.1 Table 2ZL70-30 2.602.1 Table 1ZL70-31 2.622.1 Table 1ZL70-33 2.632.1 Table 1ZL70-36 2.662.1 Table 1ZL72-30 2.604.1 Table 1ZL72-31 2.624.1 Table 1ZL72-33 2.634.1 Table 1ZL72-36 2.664.1 Table 1

Part No Cat. Pg. Part No. Cat. Pg. Part No. Cat. Pg. Part No. Cat. Pg.

12 0–5 VDC 7114950 3.421.1 4000046 3.426.1 4000049 3.430.1 4000136 3.434.112 0–10 VDC 4000070 3.422.1 4000141 3.427.1 4000124 3.431.1 4000137 3.435.112 4–20 mA 4000123 3.423.1 4000143 3.428.1 4000130 3.432.1 4000139 3.436.112 PWM — — 4000144 3.429.1 4000133 3.433.1 4000140 3.437.1

24 0–5 VDC 4000161 3.421.1 4000194 3.426.1 4000174 3.430.1 4000136 3.434.124 0–10 VDC 4000165 3.422.1 4000141 3.427.1 4000182 3.431.1 4000137 3.435.124 4–20 mA 4000169 3.423.1 4000143 3.428.1 4000186 3.432.1 4000139 3.436.124 PWM — — 4000144 3.429.1 4000133 3.433.1 4000140 3.437.1

RECOMMENDED ELECTRONIC CONTROLERS

TABLE 1 — For all PV, ZL and SP Valves (except SPxx-47, SPxx-57 and SPxx-58)

Valve Model Page No. Controllers Valve Model Page No. Controllers Valve Model Page No. Controllers

DIN Coil Mount PCB Board Only Metal Box Style DIN Rail MountControlInput

Signal

ValveCoil

Voltage

TABLE 3 — Driver/Controller for SPxx-47,SPxx-57, SPxx-58 Series Dual-Solenoid Valves

Valve Coil Voltage Driver Part No. Cat. Pg.

12 or 24 VDC 4000149 3.438.1

Part No Cat. Pg. Part No. Cat. Pg. Part No. Cat. Pg. Part No. Cat. Pg.

12 or 24 0–5 VDC 4000161 3.421.1 4000194 3.426.1 4000174 3.430.1 4000136 3.434.112 or 24 0–10 VDC 4000165 3.422.1 4000141 3.427.1 4000182 3.431.1 4000137 3.435.112 or 24 4–20 mA 4000169 3.423.1 4000143 3.428.1 4000186 3.432.1 4000139 3.436.112 or 24 PWM — — 4000144 3.429.1 4000133 3.433.1 4000140 3.437.1

RECOMMENDED ELECTRONIC CONTROLERS

TABLE 2 — For all EHPR and TS Series Valves

DIN Coil Mount PCB Board Only Metal Box Style DIN Rail MountControlInput

Signal

ValveCoil

Voltage

SP Valves and Coil Operating Parameters

2.002.1

HYDRAFORCE®

For proportional valves, performance depends on the currentin the coil. Coil current is a function of the applied voltage andthe resistance in the coil. Increasing voltage will increase thecurrent level while increasing resistance will decrease thecurrent level. In most mobile equipment electrical systems theapplied voltage is not controlled; instead it varies around thenominal battery voltage. In the case of battery-operatedvehicles the voltage decreases continually until the battery isrecharged. The internal resistance of the coil is a function ofthe material used in the coil winding, and the ambient tem-perature around the coil. As the temperature of the coilwinding increases, the electrical resistance increases. Thisresults in a decrease of the current in the coil, which candecrease the output of a proportional valve. To assure thatconstant current is delivered to the coil regardless of thischange in resistance, a closed-loop current controller shouldbe used.

In order to maintain maximum flow at high temperatures, it isimportant to know the actual applied voltage to the coilincluding any voltage drop across the controller. Generally, onengine-driven equipment where alternator voltage is severalvolts above battery voltage, a coil rated at nominal voltagemay work well. On battery-operated equipment, a coil rated atseveral volts below nominal voltage works best.

In general, it is expected that in actual application, the currentapplied to the SP valve will vary. Sometimes the currentapplied may be close to maximum, while at other times it maybe close to the threshold current. Therefore, the increase incoil resistance resulting from the power applied will typicallystabilize around a nominal or average value. This stabilized,average current value is defined as:

I-Average = (I-Threshold + I-Maximum) ÷ 2

The graphs illustrate the operating range of HydraForcestandard coils on the SP valves. The graphs show the voltagerequired to continuously maintain average current. Thevoltage supplies sufficient power to reach maximum currenton an intermittent basis. Since it is recommended to use theSP valve with a closed-loop current controller, a voltage dropof 1.5V across the controller has been taken into consider-ation in these graphs.

For example, the graph for the 08 size 10 VDC coil shows thatat an ambient temperature of 20°C, maximum current isavailable with only 83% of nominal system voltage. If ambienttemperature rises to 80°C, maximum output is achieved only if102% of nominal voltage is available to the coil. However, withthe 12 VDC coil, 102% of nominal voltage is required at 20°C.Notice that the voltage required at 80°C is above the maxi-mum 115% of nominal voltage line. This indicates that the 12VDC coil is not suitable for this ambient condition regardlessof the system voltage available.

Coil Electrical Rating

Valve Size Coil Voltage Maximum Control Current

08 10 1170 ±115 mA

08 12 1000 ±100 mA

10 10 1320 ±120 mA

10 12 1100 ±100 mA

INTRODUCTION TO SP VALVES AND COIL OPERATION

110

120

807060504030200 10-10-20

100

80

90

70

60

50PE

RC

EN

T O

F N

OM

INA

L S

YS

TE

M V

OLT

AG

E

AMBIENT TEMPERATURE (°C)

08 SIZE COILPercent of system voltage required to maintain

average current (I-ave.) at various ambient temperatures10 or 20 VDC Coil Operating Range: \ \ \12 or 24 VDC Coil Operating Range: / / /

110

120

807060504030200 10-10-20

100

80

90

70

60

50PE

RC

EN

T O

F N

OM

INA

L S

YS

TE

M V

OLT

AG

E

AMBIENT TEMPERATURE (°C)

10 SIZE COILPercent of system voltage required to maintain

average current (I-ave.) at various ambient temperatures10 or 20 VDC Coil Operating Range: \ \ \12 or 24 VDC Coil Operating Range: / / /

Note: I-Threshold varies from product to product. Refer tothe Flow vs. Current graph shown for each product.The tolerance is the same as that given for I-Max.

DESCRIPTIONA proportional solenoid-operated, 2-way, poppet-type, normally closed, screw-inhydraulic cartridge valve for low-leakage blocking and load-holding applications.

OPERATIONWhen de-energized, the SP08-20 acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀. When energized, the poppet lifts to open the ➁ to ➀flow path. Flow is proportional to current applied to the coil.

Note: If low voltage is expected on the machine, 12 or 24 volt systems willrequire the use of 10 volt or 20 volt coils respectively. See “SP Valves and CoilOperating Parameters,” page 2.002.1.

FEATURES• Industry-common cavity. • Efficient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.• Manual override options.

RATINGSOperating Pressure: 250 bar (3625 psi)Flow: 22 lpm (5.8 gpm) at 34.5 bar (500 psid)Minimum Operating Dither/Pulse Frequency: 70 HzHysteresis: Less than 5% up to 85% of I-max.; Less than 10% above 85% of I-max.Max. Internal Leakage: 5 drops per minute at 250 bar (3625 psi)Temperature: -40 to 120°C with standard Buna sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus)Installation: No Restrictions. See page 9.020.1Cavity: VC08-2; See page 9.108.1; Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-T; See page 8.650.1Coil Nut: Part No. 7004400; For E-coils manuf. prior to 1-1-04, see page 3.400.1

ELECTRO-PROPORTIONAL VALVES—DIRECTIONAL CONTROL

SP08-20 Poppet, 2-Way, Normally Closed

SYMBOLSUSASI/ISO:

2.008.1

PERFORMANCE

FLO

W lp

m/g

pm

49.2/13.0

45.4/12.0

41.6/11.0

37.9/10.0

34.1/9.0

30.3/8.0

26.5/7.0

22.7/6.0

18.9/5.0

15.2/4.0

11.4/3.0

7.6/2.0

3.8/1.0

0

FLOW vs. CURRENT at Various Differential Pressures32 cSt/150 sus oil at 40°C

PERCENT of MAX. CONTROL CURRENT

AMP (10 Volt Coil) 100 Hz Dither

10 20 30 40 50 60 70 80 90 100

0.12 0.23 0.35 0.47 0.59 0.70 0.82 0.94 1.05 1.17

250 bar3625 psi

104 bar1500 psi

35 bar500 psi

17 bar250 psi

Nominal Flow Rating

11.43

22.76

34.19

45.212

56.815

FLOW lpm/gpm

35/500

69/1000

103/1500

138/2000

172/2500

207/3000

PR

ES

SU

RE

bar

/psi

50%

of I

-max

.

75%

of I

-max

.

I-max.

PRESSURE DROP ➁ to ➀at Various Current Levels

3.4/506.9/100

10.3/15013.8/20017.2/25020.7/30024.1/35027.6/40031.0/450

7.62

15.14

22.76

30.38

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

PRESSURE DROP ➁ to ➀at 110% of I-max.

SP08-20

2.008.2

DIMENSIONS

HYDRAFORCE®

1.4035.6

3.16

TORQUE4–5 ft-lbs(5.4–6.8 Nm)max.


80.3 1.8246.2

1.41

SCREENSTANDARD

DIA.35.8

0.75 ACROSS19.1

StandardCoil View

E-CoilView

FLATS

ManualOverride

J

ManualOverride

M, T, or Y

MATERIALS

Cartridge: Weight: 0.09 kg.(0.20 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces; Buna NO-rings and back-ups standard.

Standard Ported Body: Weight:0.16 kg. (0.35 lbs.); Anodizedhigh-strength 6061 T6 aluminumalloy, rated to 240 bar (3500 psi);See page 8.008.1. Ductile ironand steel bodies available;dimensions may differ; consultfactory.

Standard Coil: Weight: 0.11 kg.(0.25 lbs.); Unitized thermoplas-tic encapsulated, Class H hightemperature magnetwire; Seepage 3.200.1.

E-Coil: Weight: 0.14 kg. (0.3 lbs.);Perfect wound, fully encapsu-lated with rugged external metalshell; Rated up to IP69K withintegral connectors; Note: Seepage 3.400.1 for all E-Coilretrofit applications.

Voltage 0 Less Coil** 10 10 VDC†

12 12 VDC 20 20 VDC†

24 24 VDC**Includes Coil Nut†10 VDC and 20 VDC

coils should be usedfor most continuous-duty applications.Consult factory.

SP08-20__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

PortingCartridge Only 0

SAE 4 4TSAE 6 6TSAE 8 8T

1/4 in. BSP* 2B3/8 in. BSP* 3B

*BSP Body; U.K. Mfr. Only

Termination (VDC)Std. Coil

DS Dual SpadesDG DIN 43650DL Leadwires (2)

DL/W Leads w/Weatherpak®

ConnectorsDR Deutsch DT04-2P

Termination (VDC)E-Coil

ER Deutsch DT04-2P(IP69K Rated)

EY Metri-Pack® 150.2A(IP69K Rated)

Frequency ResponseAverage Current ±20% Applied

-7

-6

-5

-4

-3

-2

-1

0

1 180

135

90

45

00.1 1 10 25

GA

IN (

dB)

FREQUENCY (Hz)

PH

AS

E (degrees)

PERFORMANCE (cont’d.)

Coils with internal diode areavailable. Consult factory.

Input Sig. DIN Coil PCB Metal DIN Railw/12V Coil Mount Board Box Mount0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140

Recommended Controllers (See Section 3)

OptionNone (Blank)

Manual Override MManual Override TManual Override YManual Override JFor Manual Override detailssee page 1.001.1

SealsN Buna N (Std.)V Fluorocarbon




FEATURES• Industry-common cavity. • Efficient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.• Manual override option. • Metering Option.

RATINGSOperating Pressure: 250 bar (3625 psi)Flow: 68 lpm (18 gpm) at 34.5 bar (500 psid)Minimum Operating Dither/Pulse Frequency: 70 HzHysteresis: Less than 5% up to 75% of I-max.; Less than 10% above 75% of I-max.Max. Internal Leakage: 5 drops per minute at 250 bar (3625 psi)Temperature: -40 to 120°C with standard Buna sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus)Installation: No Restrictions. See page 9.020.1Cavity: VC10-2; See page 9.108.1; Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2X-T; See page 8.650.1Coil Nut: Part No. 7004400; for E-coils manuf. prior to 1-1-04, see page 3.400.1.



SYMBOLSUSASI/ISO:

2.010.1

PERFORMANCE

FLO

W lp

m/g

pm

98.4/26

106.0/28

113.6/30

90.8/24

83.3/22

75.7/20

68.1/18

60.6/16

53.0/14

45.4/12

37.9/10

30.3/8

22.7/6

15.1/4

7.6/2

0




10 20 30 40 50 60 70 80 90 100

0.14 0.26 0.40 0.52 0.66 0.78 0.92 1.04 1.17 1.32

250 bar3625 psi

104 bar1500 psi

35 bar500 psi

17 bar250 psi

Nominal Flow Rating

1.4/202.8/404.1/605.5/80

6.9/1008.3/1209.7/140

11.0/16012.4/180

15.14

30.38

45.412

60.616

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


11.43

22.76

34.19

45.212

56.815

FLOW lpm/gpm

35/500

69/1000

103/1500

138/2000

172/2500

207/3000

PR

ES

SU

RE

bar

/psi

42%

of I

-max

.

63%

of I

-max

.

83% of I-max.


SP10-20

2.010.2

DIMENSIONS

HYDRAFORCE®

1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

3.4888.4

2.3860.5


ManualOverride

J

ManualOverride Y


0.75

ACROSS19.1

FLATS

MATERIALS






12 12 VDC 20 20 VDC†

24 24 VDC**Includes Std. Coil

Nut†10 VDC and 20 VDC


SP10-20 __ - __ __ __ - __ - __ __ __ __ __

TO ORDER









SAE 6 6TSAE 8 8T

1/4 in. BSP* 2B3/8 in. BSP* 3B1/2 in. BSP* 4B



-7

-6

-5

-4

-3

-2

-1

0

1 180

135

90

45

00.1 1 10 25

GA

IN (

dB)

FREQUENCY (Hz)

PH

AS

E (degrees)





PWM — 4000144 4000133 4000140


SealsN Buna N (Std.)V FluorocarbonP Polyurethane

OptionNone (Blank)

Screen SMetering A

Manual Override JManual Override YFor Manual Override detailssee page 1.001.1




FEATURES• Industry-common cavity. • Efficient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.• Manual override option. • Metering Option.

RATINGSOperating Pressure: 250 bar (3625 psi)Flow: 100 lpm (27 gpm) at 34.5 bar (500 psi)Minimum Operating Dither/Pulse Frequency: 70 HzHysteresis: Less than 5% below 60% of I-max.; Less than 10% above 60% of I-max.Max. Internal Leakage: 5 drops per minute at 250 bar (3625 psi)Temperature: -40 to 120°C with standard Buna sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus)Installation: No Restrictions. See page 9.020.1Cavity: VC12-2; See page 9.112.1; Cavity Tool: CT12-2XX; See page 8.600.1Seal Kit: SK12-2X-T; See page 8.650.1Coil Nut: Part No. 7004400; for E-coils manuf. prior to 1-1-04, see page 3.400.1.



SYMBOLSUSASI/ISO:

2.012.1

PERFORMANCE

FLO

W lp

m/g

pm

170/45

189/50

151/40

133/35

114/30

95/25

76/20

57/15

38/10

19/5

0



10 20 30 40 50 60 70 80 90 100

241 bar3500 psi

103 bar1500 psi

35 bar500 psi

17 bar250 psi

Nominal Flow Rating


0.14 0.26 0.40 0.52 0.66 0.78 0.92 1.04 1.17 1.32

3.4/506.9/100

10.3/15013.8/20017.2/25020.7/30024.1/35027.6/40031.0/450

37.910

56.815

94.625

18.95

75.720

113.630

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


34.19

68.118

102.227

136.336

170.345

FLOW lpm/gpm

35/500

69/1000

103/1500

138/2000

172/2500

207/3000

PR

ES

SU

RE

bar

/psi

50%

of I

-max

.

75%

of I

-max

.

100%

of I

-max

.


SP12-20

2.012.2

DIMENSIONS

HYDRAFORCE®

TORQUE33–37 ft-lbs

(44.9–50.3 Nm)max.

1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

TORQUE4–5 ft-lb5.4–6.8 Nmmax.

3.5489.9

2.4562.1

0.75

ACROSS19.1

FLATSManualOverride

J

ManualOverride Y

MATERIALS





TO ORDER



-7

-6

-5

-4

-3

-2

-1

0

1 180

135

90

45

00.1 1 10 25

GA

IN (

dB)

FREQUENCY (Hz)

PH

AS

E (degrees)



PWM — 4000144 4000133 4000140



12 12 VDC 20 20 VDC†

24 24 VDC**Includes Std. Coil

Nut†10 VDC and 20 VDC


SP12-20 __ - __ __ __ - __ - __ __ __ __ __











OptionNone (Blank)

Screen SMetering A

Manual Override JManual Override YFor Manual Override detailssee page 1.001.1



3/4 in. BSP* 6B1 in. BSP* 8B

DESCRIPTIONA proportional solenoid-operated, 2-way, poppet-type, normally closed, screw-in hydraulic cartridge valve for low-leakage blocking and load-holding applications.

OPERATIONWhen de-energized, the SP16-20 acts as a check valve, allowing fl ow from ➀ to ➁, and blocking fl ow from ➁ to ➀. When energized, the ➁ to ➀ fl ow path opens. Flow is proportional to current applied to the coil.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Industry-common cavity. • Effi cient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.• Manual override options.

RATINGSOperating Pressure: 250 bar (3625 psi)Flow: Up to 265 lpm (70 gpm); see performance curves.Dither/Pulse Frequency: 100 to 400 HzHysteresis: Less than 5% below 60% of I-max.; Less than 10% above 60% of I-max.Maximum Control Current: 1.2 ampsMax. Internal Leakage: 5 drops per minute at rated pressureTemperature: -40 to 120°C with standard Buna sealsFluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Filtration: See page 9.010.1; Installation: No Restrictions. See page 9.020.1Cavity: VC16-2; See page 9.116.1; Cavity Tool: CT16-2XX; See page 8.600.1Seal Kit: SK16-2X-T; See page 8.650.1Coil Nut: Part No. 7004400; for E-coils manuf. prior to 1-1-04, see page 3.400.1.



SYMBOLSUSASI/ISO:

2.014.1

PERFORMANCE

FLO

W lp

m/g

pm

303/80

341/90

265/70

227/60

189/50

151/40

114/30

76/20

38/10

0

FLOW vs. CURRENT at Various Differential Pressures32 cSt/150 sus oil at 40C

PERCENT of MAX. CONTROL CURRENT10 20 30 40 50 60 70 80 90 100

207 bar3000 psi

104 bar1500 psi

35 bar500 psi

11 bar160 psi

5.5 bar80 psi

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 AMP

Curves shown are for standard 12V D-Coils.for E-Coils consult factory.

3.4/506.9/100

10.3/15013.8/20017.2/25020.7/30024.1/35027.6/40031.0/450

75.720

151.440

37.910

113.630

189.350

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

PRESSURE DROP (average)Port 2 to 1; 1.5 Amp with 12 VC Coil

32 cSt/150 sus oil at 40°C

Performance information continued on following page.

HYDRAFORCE.com®

RP

Blue rectangles are links to other catalog pages.

http://www.hydraforce.com

SP16-20

2.014.2

DIMENSIONS

1.62

E-CoilViewStandard

Coil View

41.1

2.4361.8

1.84DIA.

46.7

3.5590.1

MATERIALS

Cartridge: Weight: 0.32 kg. (0.71 lbs.) Steel with hardened work surfaces. Zinc-plated exposed surfaces; Buna N O-rings and back-ups standard.

Standard Ported Body: Weight: 0.57 kg. (1.25 lbs.) Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi). Ductile iron bodies available; dimensions may differ. See page 8.016.1.

Standard Coil: Weight: 0.27 kg. (0.60 lbs.) Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.) Perfect wound, fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. Note: See page 3.400.1 for all E-Coil retrofi t applications.

TO ORDER


3810

7620

11330

15140

18950

22760

26570

1.0A

1.2A

FLOW lpm/gpm

35/500

69/1000

103/1500

138/2000

172/2500

207/3000221/3200

PR

ES

SU

RE

bar

/psi

PRESSURE RESPONSE12VDC Coil

0.75A

0.85A


12 12 VDC 20 20 VDC† 24 24 VDC**Includes Std. Coil Nut†10 VDC and 20 VDC

coils should be used for most continuous-duty applications. Consult factory.

SP16-20 __ - __ __ __ - __ - __ __ __ __ __

Termination (VDC) Std. Coil DS Dual Spades DG DIN 43650 DL Leadwires (2) DL/W Leads w/Weatherpak® Connectors DR Deutsch DT04-2P

Termination (VDC) E-Coil ER Deutsch DT04-2P (IP69K Rated) EY Metri-Pack® 150.2A (IP69K Rated)


Coils with internal diode are available. Consult factory.

SealsN Buna N (Std.) V FluorocarbonP Polyurethane

For Manual Override detailssee page 1.001.1

Note: Flow performance varies with manual override options. Consult factory for details.

Porting Cartridge Only 0 SAE 12 12T SAE 16 16T 3/4 in. BSP* 6B 1 in. BSP* 8B

Option None (Blank)

Manual Override M Manual Override Y Manual Override J

®HYDRAFORCE

HYDRAFORCE.com®

Recommended Electronic Controllers:See page 2.001.1 or our Electronics catalog.

RP



DESCRIPTIONA proportional solenoid-operated, 2-way, poppet-type, normally open, screw-inhydraulic cartridge valve for low-leakage load-holding applications and for starting orstopping a load or a pump system..

OPERATIONWhen de-energized, the SP08-21 allows flow from ➁ to ➀. When the valve is partiallyenergized, the valve begins to throttle the flow from ➁ to ➀. When fully energized, thepoppet closes on the seat, blocking flow from ➁ to ➀. Flow from ➀ to ➁ will occurwhen hydraulic pressure exceeds the solenoid force.


FEATURES• Industry-common cavity. • Efficient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 207 bar (3000 psi)Operating Voltage: See Performance ChartFlow: 0 to 22.7 lpm (0 to 6 gpm)Max. Internal Leakage: 5 drops per minute at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus)Installation: No Restrictions. See page 9.020.1Cavity: VC08-2; See page 9.108.1; Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-T; See page 8.650.1Coil Nut: Part No. 7004400;

For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut info.


SP08-21 Poppet, 2-Way, Normally Open

SYMBOLSUSASI/ISO:

2.020.1

PERFORMANCE



PWM — 4000144 4000133 4000140


1.4/20

2.8/40

4.1/60

5.5/80

6.9/100

8.3/120

9.7/140

11.0/160

3.81

7.62

11.43

18.95

15.14

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

PRESSURE DROP ➁ to ➀

1.5/0.4

3.0/0.8

4.5/1.2

6.1/1.6

7.6/2.0

9.1/2.4

10.6/2.8

35500

691000

1031500

2073000

1722500

1382000

PRESSURE bar/psi

FLO

W lp

m/g

pm

TYPICAL PRESSURE RESPONSEat 3000 psi with 12 VDC Coil

500 mA

750 mA 7.6/2.0

15.1/4.0

22.7/6.0

30.3/8.0

37.8/10.0

0.2 0.4 0.6 1.00.8CURRENT amps

FLO

W lp

m/g

pm

CURRENT RESPONSE

Note: Electronic Controller isrequired to ramp current.

SP08-21

2.020.2

DIMENSIONS

HYDRAFORCE®

MATERIALS




E-Coil: Weight: 0.14 kg. (0.3 lbs.);Perfect wound, fully encapsu-lated with rugged external metalshell; Rated up to IP69K withintegral connectors.


12 12 VDC 20 20 VDC†



SP08-21 - __ __ __ - __ - __ __ __ __ __

TO ORDER





SealsBuna N (Std.) NFluorocarbon VPolyurethane P

Termination (VDC) Std. CoilDS Dual SpadesDG DIN 43650DL Leadwires (2)



Termination (VDC) E-CoilER Deutsch DT04-2P

(IP69K Rated)EY Metri-Pack® 150.2A

(IP69K Rated)


1.4035.6

2.74



69.6

1.41 DIA.35.8

StandardCoil View

E-CoilView

DESCRIPTIONA proportional solenoid-operated, 2-way, poppet-type, normally open, screw-in hydraulic cartridge valve for low-leakage blocking and load-holding applications

OPERATIONWhen de-energized, the SP16-21 allows fl ow from ➁ to ➀. When the valve is partially energized, the valve begins to throttle the fl ow from ➁ to ➀. When fully energized, the poppet closes on the seat, blocking fl ow from ➁ to ➀. Flow from ➀ to ➁ will occur when hydraulic pressure exceeds the solenoid force.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Industry-common cavity. • Effi cient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.• Manual override option.

RATINGSOperating Pressure: 250 bar (3625 psi)Flow: 265 lpm (70 gpm); see performance chartsMax. Internal Leakage: 7 drops per minute at 207 bar (3000 psi)Dither/Pulse Frequency: 100 to 400 HzHysteresis: Less than 10% up to 70% of I-max.; Less than 5% above 70% of I-max.Maximum Control Current: 1.2 amp required to achieve rated fl owThreshold Current: 0.3 A; see performance chartsTemperature: -40 to 120°C with standard Buna sealsFluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Filtration: See page 9.010.1; Installation: No Restrictions. See page 9.020.1Cavity: VC16-2; See page 9.116.1; Cavity Tool: CT16-2XX; See page 8.600.1Seal Kit: SK16-2X-T; See page 8.650.1Coil Nut: Part No. 7004400


SP16-21 Poppet, 2-Way, Normally Open

SYMBOLSUSASI/ISO:

2.023.1

PERFORMANCE

HYDRAFORCE.com®


FLO

W lp

m/g

pm

303/80

265/70

227/60

189/50

151/40

114/30

76/20

38/10

0



A

C

D

10 20 30 40 50 60 70 80 90 100

Nominal Flow Rating

AMP (12 Volt Standard Coil) 70 Hz Dither0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2

B

Pressure Drop 100 mA 1200 mAD 1000 psi 3000 psiC 700 psi 1530 psiB 450 psi 550 psiA 150 psi 230 psi

37.910

75.720

113.630

151.440

189.350

227.160

0 mA

FLOW lpm/gpm

35/500

69/1000

103/1500

138/2000

172/2500

207/3000

241/3500

PR

ES

SU

RE

bar

/psi

PRESSURE RESPONSEwith 12 VDC Coil

800 mA

600 mA

400 mA

RP



SP16-21

2.023.2

DIMENSIONS

MATERIALS



Standard Coil: Weight: 0.27 kg. (0.60 lbs.) Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.) Perfect wound, fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. See page 3.400.1.

TO ORDER


12 12 VDC 20 20 VDC† 24 24 VDC**Includes Std. Coil Nut†10 VDC and 20 VDC

coils should be used for most continuous-duty applications. Consult factory.

SP16-21 __ - __ __ __ - __ - __ __ __ __ __

Termination (VDC) Std. Coil DS Dual Spades DG DIN 43650 DL Leadwires (2) DL/W Leads w/Weatherpak® Connectors DR Deutsch DT04-2P

Termination (VDC) E-Coil ER Deutsch DT04-2P (IP69K Rated) EY Metri-Pack® 150.2A (IP69K Rated)




Porting Cartridge Only 0 SAE 12 12T SAE 16 16T 3/4 in. BSP* 6B 1 in. BSP* 8B

Option None (Blank)

Manual Override P

®HYDRAFORCE

HYDRAFORCE.com®

1.62

E-CoilViewStandard

Coil View

41.1

3.4186.6

1.84

TORQUE:5 – 7 ft-lbs6.8 – 9.5 Nm

DIA.46.7

3.98101.1

TORQUE:46 – 54 ft-lbs

62.4 – 73.2 Nm

Seals Buna N (Std.) N Fluorocarbon V Polyurethane P

RP




OPERATIONWhen de-energized, the SP08-22 acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀. When energized, the poppet lifts to open the ➁ to ➀flow path. There is a free-reverse-flow check to allow flow from ➀ to ➁ when ener-gized. Flow is proportional to current applied to the coil.

Note: External circuitry is required to ramp current.


FEATURES• Industry-common cavity. • Hardened steel work surfaces.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: 30.3 lpm (8 gpm) nominalMax. Internal Leakage: 328 ml/minute (20 cu. in./minute) at 207 bar (3000 psi)Temperature: -40 to 100°C with standard Buna sealsFiltration: Recommend ISO 4406 16/13; See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus)Installation: No Restrictions. See page 9.020.1Cavity: VC08-2; See page 9.108.1; Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-M; See page 8.650.1Coil Nut: Part No. 7004400; For E-coils manuf. prior to 1-1-04, see page 3.400.1



SYMBOLSUSASI/ISO:

2.024.1

PERFORMANCE

FLO

W lp

m/g

pm

49.2/13.0

45.4/12.0

41.6/11.0

37.9/10.0

34.1/9.0

30.3/8.0

26.5/7.0

22.7/6.0

18.9/5.0

15.2/4.0

11.4/3.0

7.6/2.0

3.8/1.0

0

FLOW vs. CURRENT at Various Differential Pressuresfor Standard Coils (consult factory for E-Coils)




10 20 30 40 50 60 70 80 90 100

0.12 0.23 0.35 0.46 0.58 0.69 0.81 0.92 1.04 1.15

207 bar3000 psi

104 bar1500 psi

35 bar500 psi

10 bar150 psi

8 gpm Nominal Flow Rating

11.43

22.76

34.19

45.212

56.815

FLOW lpm/gpm

35/500

69/1000

103/1500

138/2000

172/2500

207/3000

PR

ES

SU

RE

bar

/psi

0.5

amp

0.65

am

p

0.85

am

p

1.0 amp

TYPICAL PRESSURE RESPONSE12 VDC Coil

3.4/50

6.9/100

10.3/150

13.8/200

17.2/250

20.7/300

7.62

3.81

11.43

15.14

18.95

22.76

26.57

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

TYPICAL PRESSURE DROP ➁ to ➀with 12 VDC Coil

1.0

amp

1.3 amp

SP08-20

2.024.2

DIMENSIONS

HYDRAFORCE®

1.4035.6

1.91


TORQUE19–21 ft-lbs(25.8–28.5 Nm)

48.51.9148.5

1.41

SCREENSTANDARD

DIA.35.8

0.75 ACROSS19.1

StandardCoil View

E-CoilView

FLATS

MATERIALS






12 12 VDC 20 20 VDC†



SP08-22__ - __ __ __ - __ - __ __ __ __ __

TO ORDER












PERCENT I-MAX. vs. TEMPERATUREfor 10 or 20 VDC Coil (for 10V Coil I-Max. = 1.15A)

78

80

82

84

86

88

90

92

94

96

98

100

102

-4-20

320

6820

10440

14060

17680

PE

RC

EN

T o

f I-M

AX

.

TEMPERATURE (°F/°C)

Curves show percent of nominal system voltage minus 1.5V drop across controller

100%85%

115%





PWM — 4000144 4000133 4000140


OptionNone (Blank


DESCRIPTIONA proportional solenoid-operated, 2-way, spool-type, normally closed, screw-in hydraulic cartridge valve designed to operate as a bi-directional metering valve.

OPERATIONWhen de-energized, the SP08-24 blocks flow in both directions. When the coil is partially energized, the valve begins to throttle flow. When fully energized, the valve opens to allow full, bi-directional flow.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Industry-common cavity. • Efficient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 207 bar (3000 psi)Operating Voltage: See Performance ChartFlow: up to 11.4 lpm (3 gpm)Max. Internal Leakage: 164 cc (10 cu. in.) per minute at 207 bar (3000 psi)Maximum Control Current: 100 mA (12 VDC coil)Minimum Control Current: 400 mA (12 VDC coil)Threshold Current: 400 mA (12 VDC coil)Hysteresis: < 10% full flowDither/PWM Frequency Range: 70 Hz min.Operating Temperature: -40 to 100°C (-40° to 212°F) with standard Buna N seals

-26 to 204°C (-15°F to 400°F) with Fluorocarbon seals-54 to 107°C (-65°F to 225°F) with Polyurethane seals

Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No Restrictions. See page 9.020.1Cavity: VC08-2; See page 9.108.1; Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-M; See page 8.650.1Coil Nut: Part No. 7004400


SP08-24 Spool, 2-Way, Normally Closed

SYMBOL

2.026.1

PERFORMANCE

HYDRAFORCE.com®

Recommended Electronic Controllers:See page 2.001.1 or our Electronics catalog.3.4/50

6.9/100

10.3/150

13.8/200

17.2/250

20.7/300

3.81.0

1.90.5

5.71.5

7.62.0

11.43.0

9.52.5

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

PRESSURE DROP vs. FLOWPort 1 to 2, or 2 to 1

1.5/0.4

3.0/0.8

4.5/1.2

6.1/1.6

7.6/2.0

9.1/2.4

10.6/2.8

12.1/3.2

35500

691000

1031500

2073000

2413500

1722500

1382000

DIFFERENTIAL PRESSURE bar/psi

FLO

W lp

m/g

pm

TYPICAL PRESSURE RESPONSEPort 1 to 2, or 2 to 1

1.00 A

0.85 A

0.65 A

0.50 A1.9/0.5

3.8/1.0

5.7/1.5

7.6/2.0

9.5/2.5

11.4/3.0

0.10.2

0.30.4

0.50.6

0.70.8

0.91.0

CURRENT amps

FLO

W lp

m/g

pm

CURRENT RESPONSEat 10.3 bar/150 psi; 12 VDC Coil

Port 1 to 2, or 2 to 1

Typical RangeShaded

0.8/0.2

1.5/0.4

2.3/0.6

3.0/0.8

3.8/1.0

4.5/1.2

5.3/1.4

6.1/1.6

6.8/1.8

0.10.2

0.30.4

0.50.6

0.70.8

0.91.0

CURRENT amps

FLO

W lp

m/g

pm

CURRENT RESPONSEat 207 bar/3000 psi; 12 VDC Coil

Port 1 to 2, or 2 to 1

Typical RangeShaded

RP



SP08-24

2.026.2

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.11 kg. (0.25 lbs.) Steel with hardened work surfaces. Zinc-plated exposed surfaces Buna N O-rings and back-ups standard.


Standard Coil: Weight: 0.11 kg. (0.25 lbs.) Unitizedthermoplastic encapsulated, Class H high temperature magnetwire.See page 3.200.1

E-Coil: Weight: 0.14 kg. (0.3 lbs.) Perfect wound, fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. See page 3.400.1

SP08-24 __ - __ __ __ - __ - __ __ __ __ __

TO ORDER

Porting Cartridge Only 0 SAE 4 4T SAE 6 6T 1/4 in. BSP* 2B 3/8 in. BSP* 3B



®HYDRAFORCE

HYDRAFORCE.com®

Voltage **Less Coil 0 †10 VDC 10 12 VDC 12 †20 VDC 20 24 VDC 24

1.4035.6

3.38



85.8

1.10

ManualOverrideOption P

27.8

2.7469.6

1.41 DIA.35.8

StandardCoil View

E-CoilView


**Includes Coil Nut†10 VDC and 20 VDC coils should be used

for most continuous-duty applications. Consult factory.

Option None (Blank) Screen S Manual Override P

For Coils with Zener Diode, add “/Z” to option code. For example: “ER/Z”. Not available on all models. See coil option info. on pages 3.200.1 & 3.400.1

Coil Termination E-Coil D-CoilDeutsch DT04-2P ER (IP69K) DR (IP65)Metri-Pak 150 EY (IP69K) DY (IP65)Dual Lead Wires EL (IP69K) DL (IP65)Amp Jr. Timer EJ (IP67) —DIN 43650 EG (IP65) DG (IP65)Dual Spades — DS (IP65)

RP



DESCRIPTIONA proportional solenoid-operated, 2-way, spool-type, normally-closed, direct-acting, screw-in hydraulic cartridge valve for bi-directional metering.

OPERATIONWhen energized, the SP10-24 acts as a bi-directional metering valve. When de-energized, the valve blocks fl ow in both directions.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Industry-common cavity. • Effi cient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.• Manual Override option.

RATINGSOperating Pressure: 207 bar (3000 psi)Minimum Operating Dither/Pulse Frequency: 70 HzFlow: 0 to 26.5 lpm (0 to 7 gpm)Max. Internal Leakage: 328 cc/minute (20 cu. in./minute) at 207 bar (3000 psi)Operating Temperature: -40 to 100°C (-40° to 212°F) with standard Buna N seals

-26 to 204°C (-15°F to 400°F) with Fluorocarbon seals-54 to 107°C (-65°F to 225°F) with Polyurethane seals


7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No Restrictions. See page 9.020.1Cavity: VC10-2; See page 9.110.1; Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2X-M; See page 8.650.1Coil Nut: Part No. 7004420


SP10-24 Spool, 2-Way, Normally Closed, Metering

SYMBOL

2.027.1

PERFORMANCE

HYDRAFORCE.com®

Performance charts continued on next page.

3.8/1.0

7.6/2.0

11.4/3.0

22.7/6.0

18.9/5.0

15.1/4.0

0.1 0.2 0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:

40302010 70 80 90 10050 60% of Max. Control Current:

FLO

W lp

m/g

pm

Typical Flow vs. Currentat 11 bar (160 psi) with 12 VDC Coil

Shaded Area = Range

1.9/0.5

3.8/1.0

5.7/1.5

7.6/2.0

15.1/4.0

13.3/3.5

11.4/3.0

9.5/2.5

0.1 0.2 0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:

FLO

W lp

m/g

pm

Typical Flow vs. Currentat 207 bar (3000 psi) with 12 VDC Coil

Shaded Area = Range

40302010 70 80 90 10050 60% of Max. Control Current:

1.7/25

3.4/50

5.2/75

6.9/100

8.6/125

10.3/150

7.62

3.91

15.14

11.43

18.95

22.76

26.57

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Pressure Drop at I-Max.

2 to 1

1 to 2

RP



SP10-24

2.027.2

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.17 kg. (0.37 lbs.) Steel with hardened work surfaces. Zinc-plated exposed surfaces Buna N O-rings and back-ups standard.

Standard Ported Body: Weight: 0.16 kg. (0.35 lbs.) Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi). Ductile iron bodies available; dimensions may differ.See page 8.010.1.

Standard D-Coil: Weight: 0.27 kg. (0.60 lbs.) Unitized thermoplas-tic encapsulated, Class H high temperature magnetwire. See page 3.200.1

E-Coil: Weight: 0.41 kg. (0.9 lbs.) Perfect wound, fully encapsu-lated with rugged external metal shell. Rated up to IP69K with integral connectors. See page 3.400.1

SP10-24__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

Porting Cartridge Only 0 SAE 6 6T SAE 8 8T 1/4 in. BSP* 2B 3/8 in. BSP* 3B 1/2 in. BSP* 4B *BSP Body; U.K. Mfr. Only

Voltage **Less Coil 0 †10 VDC 10 12 VDC 12 †20 VDC 20 24 VDC 24


®HYDRAFORCE

HYDRAFORCE.com®


Option None (Blank)

Manual Override P Manual Override K



3.8/1

7.6/2

11.4/3

15.1/4

18.9/5

22.7/6

26.5/7

30.3/8

35500

691000

1031500

2073000

1722500

1382000

PRESSURE bar/psi

FLO

W lp

m/g

pm

Typical Pressure ResponsePort 1 to 2 ——; Port 2 to 1 - - - -

1200 mA

850 mA

750 mA

1.6241.1

1.84DIA.

46.7

E-CoilView

D-CoilView

3.98101.0

ManualOverrideOption

“P”

ManualOverride

Option “K”

Coil Must BeInstalled withLettering Up

3.3384.6

TORQUE4–5 ft-lbs

(5.4–6.8 Nm)




**Includes Coil Nut and Spacer.†10 and 20 VDC coils should be used for most continuous-duty applications. Consult factory.

RP



DESCRIPTIONA proportional solenoid-operated, 2-way, spool-type, normally open, bi-directional,screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SP08-25 allows flow from ➀ to ➁ or from ➁ to ➀. Whenpartially energized, the valve begins to throttle the flow in either direction. When fullyenergized, flow is blocked in either direction.

External circuitry is required to ramp current.


FEATURES• Industry-common cavity.• Continuous-duty rated coils.• Hardened precision spool and cage for long life.• Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 207 bar (3000 psi)Operating Voltage: See performance chartFlow: 0 to 15.4 lpm (0 to 4 gpm)Internal Leakage: 5 drops per minute at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsFiltration: Recommend ISO 4406 16/13; See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus)Installation: No Restrictions. See page 9.020.1Cavity: VC08-2; See page 9.108.1Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-T; See page 8.650.1


SP08-25 Spool, 2-Way, Normally Open

SYMBOLSUSASI/ISO:

2.028.1

PERFORMANCE

15.1/4

18.9/5

7.6/2

11.4/3

3.8/1

250 500 750 1000

CURRENT mA

FLO

W lp

m/g

pm

Current Response

Acceptable Range

1.4/202.8/404.1/605.5/80

6.9/1008.3/1209.7/140

11.0/16012.4/18013.8/200

3.81

7.62

11.43

18.95

15.14

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Pressure Drop

➁ to ➀

➀ to ➁

691000

35500

PRESSURE bar/psi

FLO

W lp

m/g

pm

1382000

1031500

2073000

1722500

6.06/1.6

5.30/1.4

7.57/2.0

6.81/1.8

9.08/2.4

8.33/2.2

9.84/2.6

4.54/1.2

3.79/1.0

3.03/0.8

2.27/0.6

1.51/0.4

0.76/0.2

Typical PressureResponse with 12VDC Coil

0.25 AMP

0.50 AMP

0.75 AMP

SP08-25

2.028.2

DIMENSIONS

HYDRAFORCE®

1.4035.6

1.91



48.6

1.41 DIA.35.8

StandardCoil View

E-CoilView

MATERIALS




E-Coil: Weight: 0.14 kg. (0.3 lbs.);Perfect wound, fully encapsu-lated with rugged external metalshell; Rated up to IP69K withintegral connectors.


12 12 VDC 20 20 VDC†



SP08-25 - __ __ __ - __ - __ __ __ __ __

TO ORDER





SealsBuna N (Std.) NFluorocarbon VPolyurethane P

Termination (VDC) Std. CoilDS Dual SpadesDG DIN 43650DL Leadwires (2)



Termination (VDC) E-CoilER Deutsch DT04-2P

(IP69K Rated)EY Metri-Pack® 150.2A

(IP69K Rated)

ELECTRONIC CONTROLLERS


Input Sig. DIN Coil PCB Metal DIN Railw/12V Coil Mount Board Box Mount

0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140


DESCRIPTIONA proportional, solenoid-operated, 4-way, 2-position, screw-in hydraulic cartridgevalve.

OPERATIONWhen de-energized, the SP08-41 blocks flow to all ports. When energized, meteredflow is allowed from ➂ to ➃, as well as metered return flow from ➁ to ➀. Please notethat this valve will allow flow from ➃ to ➂ and from ➀ to ➁ but these flows will not bemetered.

FEATURES• Continuous-duty rated solenoid.• Hardened parts for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Good linearity and hysteresis.• Industry common cavity.

RATINGSOperating Pressure: 247 bar (3625 psi) with standard Buna N sealsFlow: 11.4 lpm (3 gpm) maximum; see performance chartInternal Leakage: 328 ml/minute (20 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Standard Coils and E-Coils: Continuous from 85% to 115% of

nominal voltageFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-4; See page 9.108.1Cavity Tool: CT08-4XX; See page 8.600.1Seal Kit: SK08-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400;


SP08-41 Spool, 4-Way, 2-Position

USASI/ISO:

SYMBOLS

PERFORMANCE (Cartridge Only)

2.078.1

11.4/3.0

7.5/2.0

9.5/2.5

3.8/1.0

5.7/1.5

1.9/0.5

0.2 0.4 0.6 0.8 1.0 1.2

CURRENT amps

FLO

W lp

m/g

pm

Flow vs. Current100 Hz PWM; 12 VDC


Acceptable Range


5.2/75

3.4/50

1.7/25

01.90.5

3.81.0

5.71.5

7.62.0

9.52.5

11.43.0

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➃, S2 energized: ———➁ to ➀, S1 energized: - - - - - -

32 cSt/150 sus oil at 40°C 9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

069

1000138

2000207

3000

PRESSURE bar/psi

FLO

W lp

m/g

pm

Pressure Compensation, Inlet to Work PortTypical Differential Pressure32 cSt/150 sus oil at 40°C

0.7 ampCurrent

1.0 ampCurrent

0.5 ampCurrent



PWM — 4000144 4000133 4000140


SP08-41

DIMENSIONS

2.078.2

Standard Coil View

1.91



(25.8–28.5 Nm)

48.61.9148.6

E-CoilView

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

MATERIALS

Voltage 0 Less Coil** 12 12 VDC 24 24 VDC

**Includes Coil Nut

TO ORDER

Cartridge: Weight: 0.13 kg. (0.28 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. BunaN O-rings and single-turn polyesterelastomer back-up standard.

Standard Ported Body: Weight:0.27 kg. (0.60 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); See page8.008.1. Steel and Ductile Iron bodiesavailable, dimensions may differ,consult factory.

Standard Coil: Weight: 0.11 kg.(0.25 lbs.); Unitized thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

E-Coil: Weight: 0.14 kg. (0.3 lbs.);Perfect wound, fully encapsulatedwith rugged external metal shell;Rated up to IP69K with integralconnectors; Note: See page 3.400.1for all E-Coil retrofit applications.

SP08-41__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)

SealsBuna N (Std.) NFluorocarbon V

VoltageE-Coil

12 12 VDC 24 24 VDC






EY Metri-Pack® 150(IP69K Rated)



SP10-41 Spool, 4-Way, 2-Position, Normally Closed

USASI/ISO:

SYMBOLS


2.080.1

22.7/6

15.1/4

18.9/5

26.5/7

7.5/2

11.4/3

3.8/1

0.2 0.4 0.6 0.8 1.0 1.2

CURRENT amps

FLO

W lp

m/g

pm

Flow vs. Current100 Hz PWM

32 cSt/150 ssu oil at 40°C

Acceptable Range


DESCRIPTIONA proportional, solenoid-operated, 4-way, 2-position, normally closed, spool-type,screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SP10-41 blocks flow to all ports. When the coil is energized,metered flow is allowed from ➂ and ➃, as well as metered return flow from ➁ to ➀.

While port ➀ may be fully pressurized, it is not intended for use as the valve’s inlet.

In circuits where work port flows are unequal due to cylinder ratios, the higher returnflow should be directed to port ➁.

Note: Valve will allow flow from ➀ to ➁ and from ➃ to ➂ but flow will not be metered.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Good linearity and hysteresis.• Industry common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: 20.8 lpm (5.5 gpm) maximum; see performance chartInternal Leakage: 164 ml/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Standard Coils and E-Coils: Continuous from 85% to 115% of





0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140


SP10-41

DIMENSIONS

2.080.2

1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

TORQUE:5–7 ft-lbs

(6.8–9.5 Nm)max.

TORQUE:24–26 ft-lbs

(32.5–35.3 Nm)max.

HYDRAFORCE®

MATERIALS


**Includes Coil Nut

TO ORDER

Cartridge: Weight: 0.20 kg. (0.45 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces.Buna N O-rings and single-turnpolyester elastomer back-upstandard.

Standard Ported Body: Weight:0.36 kg. (0.80 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.010.1. Ductile iron and steelbodies available; dimensions maydiffer; consult factory.

Standard Coil: Weight: 0.27 kg.(0.60 lbs.); Unitized thermoplasticencapsulated, Class H hightemperature magnetwire;See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.);Perfect wound, fully encapsulatedwith rugged external metal shell;Rated up to IP69K with integralconnectors; Note: See page3.400.1 for all E-Coil retrofitapplications.

SP10-41__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)


VoltageE-Coil

12 12 VDC 24 24 VDC








EG DIN 43650(IP65 Rated)



OPERATIONWhen de-energized, the SP08-46R allows flow from ➁, ➀ and ➃, while blocking flowat ➂. When energized, metered flow is allowed from ➂ to ➃, as well as meteredreturn flow from ➁ to ➀. Please note that this valve will allow flow from ➃ to ➂ andfrom ➀ to ➁ but these flows will not be metered.

FEATURES• Continuous-duty rated solenoid.• Hardened parts for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Good linearity and hysteresis.• Industry common cavity.





SP08-46R Spool, 4-Way, 2-Position

USASI/ISO:

SYMBOLS


2.088.1

11.4/3.0

7.5/2.0

9.5/2.5

3.8/1.0

5.7/1.5

1.9/0.5

0.2 0.4 0.6 0.8 1.0 1.2

CURRENT amps

FLO

W lp

m/g

pm



Acceptable Range


5.2/75

3.4/50

1.7/25

01.90.5

3.81.0

5.71.5

7.62.0

9.52.5

11.43.0

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


32 cSt/150 sus oil at 40°C 15.1/4.0

9.5/2.5

11.4/3.0

13.2/3.5

7.6/2.0

5.7/1.5

3.8/1.0

069

1000138

2000207

3000

PRESSURE bar/psi

FLO

W lp

m/g

pm


0.7 ampCurrent

1.0 ampCurrent

0.5 ampCurrent



PWM — 4000144 4000133 4000140


SP08-46R

DIMENSIONS

2.088.2

Standard Coil View

1.91



(25.8–28.5 Nm)

48.61.9148.6

E-CoilView

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

MATERIALS


**Includes Coil Nut

TO ORDER





SP08-46R__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)


VoltageE-Coil

12 12 VDC 24 24 VDC









SP10-46R Spool, 4-Way, 2-Position

USASI/ISO:

SYMBOLS


2.090.1

22.7/6

15.1/4

18.9/5

26.5/7

7.5/2

11.4/3

3.8/1

0.2 0.4 0.6 0.8 1.0 1.2

CURRENT amps

FLO

W lp

m/g

pm



Acceptable Range



OPERATIONWhen de-energized, the SP10-46R allows flow from ➁, ➀ and ➃, while blocking flowat ➂. When energized, metered flow is allowed from ➂ to ➃, as well as meteredreturn flow from ➁ to ➀.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Good linearity and hysteresis.• Industry common cavity.





10.3/150

6.9/100

3.4/50

03.81

7.52

11.43

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


32 cSt/150 sus oil at 40°C 18.9/5

15.1/4

11.4/3

7.6/2

3.8/1

069

10001382000

2073000

PRESSURE bar/psi

FLO

W lp

m/g

pm


0.7 ampCurrent

0.5 ampCurrent



PWM — 4000144 4000133 4000140


SP10-46R

DIMENSIONS

2.090.2

1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

TORQUE:5–7 ft-lbs

(6.8–9.5 Nm)max.

TORQUE:24–26 ft-lbs

(32.5–35.3 Nm)max.

HYDRAFORCE®

MATERIALS


**Includes Coil Nut

TO ORDER





SP10-46R__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)


VoltageE-Coil

12 12 VDC 24 24 VDC








EG DIN 43650(IP65 Rated)


DESCRIPTIONA proportional solenoid-operated, 4-way, 3-position, spool-type, closed center, screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SP08-47C blocks flow to all ports. When coil S1 is energized,flow is allowed from ➂ to ➃, and from ➁ to ➀. When coil S2 is energized, flow isallowed from ➂ to ➁, and from ➃ to ➀.

Initial meter-in flow begins at a nominal 0.4 amp on a 12 VDC system. Full flow of3 gpm occurs at 1.0 to 1.1 amp on a 12 VDC system. Each coil has its own meteringcharacteristics, which are quite similar (see performance chart).



FEATURES• Continuous-duty rated solenoids. • Optional manual override.• Efficient wet-armature construction. • Industry-common cavity.• Optional coil voltages and terminations.• Hardened precision spool and cage for long life.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Designed for good linearity and hysteresis.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: 11.4 lpm (3 gpm) max. (see performance chart); Flow rate is based on 50%

duty cycle and coil temperature of 20°C (140°F). Consult factory if higher dutycycle and coil temperatures are anticipated.

Internal Leakage: 164 cc/minute (10 cu. in./minute) max. per sideat 207 bar (3000 psi)

Hysteresis: Less than 7%Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Standard Coils and E-Coils: Continuous up to 115%

of nominal voltageFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 ssu)Installation Recommendation: When possible, the valve should be mounted below

the reservoir oil level. This will maintain oil in the armature preventing trapped airinstability. If this is not feasible, mount the valve horizontally for best results.See page 9.020.1

Cavity: VC08-4; See page 9.108.1; Cavity Tool: CT08-4XX; See page 8.600.1Seal Kit: SK08-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180;Coil Spacer: Part No. 4534720For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.


SP08-47C Spool, 4-Way, 3-Position, Closed Center

SYMBOLSUSASI:

ISO:

2.110.1


10.4/150

6.9/100

3.5/50

3.81

7.52

11.43

15.14

FLOW lpm/gpmPR

ES

SU

RE

DR

OP

bar

/psi


INLET

OUTLET

7.5/2

11.4/3

15.1/4

3.8/1

01.0 1.00.5 0.50

AMPERAGE with100 Hz PWM

FLO

W lp

m/g

pm

Top Coil Bottom Coil

E-Coil

E-Coil

Std. Coil Std. Coil


Recommended ControllerDual Solenoid DriverPart No. 4000149(See page 3.550.1)

SP08-47C__ - __ __ __ - __ - __ __ __ __ __

MATERIALS

Cartridge: Steel with hardenedwork surfaces. Zinc-platedexposed surfaces. Buna NO-rings and single-turn polyesterelastomer back-ups standard.


Standard Coil: (2 required)Weight each: 0.11 kg (0.25 lbs.);Unitized thermoplastic encapsu-lated, Class H high temperaturemagnetwire; See page 3.200.1.

E-Coil: (2 required) Weight each:0.14 kg (0.3 lbs.); Fully encapsu-lated with external metal shell;Rated up to IP69K with integralconnectors; See page 3.400.1.

TO ORDER

VoltageStandard Coil

0 Less Coil**12 12 VDC24 24 VDC**Includes Std. Coil Nut

SP08-47C

2.110.2

OptionNone (Blank)

Manual Override BManual Override M



SAE 6 6T1/4 in. BSP* 2B3/8 in. BSP* 3B

*BSP Body;U.K. Mfr. Only

DIMENSIONS

HYDRAFORCE®

2.9274.2

E-Coil Dia.

Option "B"1.50 38.1

Option "M"Manual Override

COILS MUST BEINSTALLED WITHLETTERING UP

1.4135.8

Across FlatsTORQUE:4–5 ft-lbs

(5.5–6.8 Nm)Max.

0.7519.1

1.1328.7

1.2531.8 2.50

63.5

3.3384.7

S1

S2

Across FlatsTORQUE:

16–20 ft-lbs(24.4–27.1 Nm)

Max.

0.8822.2

2.1554.6

4

4.95125.7

2.1153.4

SHOWN ABOVEWITH E-COILS AND

EY CONNECTORS OPTION

3

2

1

INCHMILLIMETRE

1.1729.7

2.8472.1

3.2582.6

0.256.4

2.0050.8

0.287.1

1.7343.9

0.6015.2

4

2

1

3

Knob: Dia.

VoltageE-Coil

12 12 VDC24 24 VDC


691000


FLO

W lp

m/g

pm

Pressure CompensationInlet to Work Port

1382000

2073000

15.1/4

11.4/3

7.6/2

3.8/1

1.0 AMP

0.75 AMP

0.50 AMP









DESCRIPTIONA proportional solenoid-operated, 4-way, 3-position, spool-type, closed center, screw-in hydraulic cartridge valve with lower maximum flow rate of 7.6 lpm (2 gpm).

OPERATIONWhen de-energized, the SP08-47CL blocks flow to all ports. When coil S1 isenergized, flow is allowed from ➂ to ➃, and from ➁ to ➀. When coil S2 is energized,flow is allowed from ➂ to ➁, and from ➃ to ➀.




FEATURES• Continuous-duty rated solenoids. • Optional manual override.• Efficient wet-armature construction. • Industry-common cavity.• Optional coil voltages and terminations.• Hardened precision spool and cage for long life.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Designed for good linearity and hysteresis.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: 7.6 lpm (2 gpm) max. (see performance chart); Flow rate is based on 50% duty

cycle and coil temperature of 20°C (140°F). Consult factory if higher duty cycle andcoil temperatures are anticipated.








SP08-47CL Spool, 4-Way, 3-Position, Closed Center,

SYMBOLSUSASI:

ISO:

2.111.1


6.9/100

5.2/75

3.5/50

1.7/25

3.81.0

1.90.5

7.62.0

5.71.5

FLOW lpm/gpmPR

ES

SU

RE

DR

OP

bar

/psi


3 to 2or 3 to 4

2 to 1or 4 to 1

3.8/1.0

5.7/1.5

7.6/2.0

1.9/0.5

01.0 1.00.5 0.50

AMPERAGE with 12 VDC System

FLO

W lp

m/g

pm

S1 - Top Coil S2 - Bottom Coil



SP08-47CL__ - __ __ __ - __ - __ __ __ __ __

MATERIALS


Standard Ported Body: Weight:0.18 kg. (0.40 lbs.); Anodizedhigh-strength 6061 T6 aluminumalloy, rated to 240 bar (3500psi); See page 8.008.1. Ductileiron and steel bodies available;dimensions may differ; consultfactory.



TO ORDER



SP08-47CL

2.111.2

OptionNone (Blank)






DIMENSIONS

HYDRAFORCE®

2.9274.2

E-Coil Dia.

Option "B"1.50 38.1



1.4135.8


(5.5–6.8 Nm)Max.

0.7519.1

1.1328.7

1.2531.8 2.50

63.5

3.3384.7

S1

S2

Across FlatsTORQUE:

16–20 ft-lbs(24.4–27.1 Nm)

Max.

0.8822.2

2.1554.6

4

4.95125.7

2.1153.4



3

2

1

INCHMILLIMETRE

1.1729.7

2.8472.1

3.2582.6

0.256.4

2.0050.8

0.287.1

1.7343.9

0.6015.2

4

2

1

3

Knob: Dia.

VoltageE-Coil

12 12 VDC24 24 VDC


691000


FLO

W lp

m/g

pm


1382000

2073000

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

1.0 AMP

0.75 AMP

0.50 AMP









Low Flow Version

DESCRIPTIONA proportional solenoid-operated, 4-way, 3-position, spool-type, closed center, screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SP10-47C blocks flow to all ports. When coil S1 is energized,flow is allowed from ➂ to ➃, and from ➁ to ➀. When coil S2 is energized, flow isallowed from ➂ to ➁, and from ➃ to ➀.




FEATURES• Continuous-duty rated solenoids.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Optional manual override.• Industry-common cavity.• Designed for good linearity and hysteresis.

RATINGSOperating Pressure: 248 bar (3600 psi)Flow: 22.7 lpm (6 gpm) max. (see performance chart)Internal Leakage: 164 cc/minute (10 cu. in./minute) max. per side

at 248 bar (3600 psi)Hysteresis: Less than 7%Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Standard Coils and E-Coils: Continuous up to 115%




Cavity: VC10-4; See page 9.110.1; Cavity Tool: CT10-4XX; See page 8.600.1Seal Kit: SK10-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180Coil Spacer: Part No. 4539700For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.


SP10-47C Spool, 4-Way, 3-Position, Closed Center

SYMBOLSUSASI:

ISO:

2.112.1


10.4/150

6.9/100

3.5/50

3.81

7.52

11.43

15.14

18.95

22.76

FLOW lpm/gpmPR

ES

SU

RE

DR

OP

bar

/psi


INLET

OUTLET

15.1/4

22.7/6

7.5/2

01.0 1.00.5 0.50

AMPERAGE with 100 Hz Dither

FLO

W lp

m/g

pm


E-Coil

Std. Coil

E-Coil

Std. Coil



MATERIALS

Cartridge: Weight: 0.30 kg.(0.65 lbs.) Steel with hardenedwork surfaces. Zinc-platedexposed surfaces. Buna NO-rings and single-turn polyesterelastomer back-ups standard.


Standard Coil: (2 required) Weighteach: 0.27 kg. (0.60 lbs.);Unitized thermoplastic encapsu-lated, Class H high temperaturemagnetwire; See page 3.200.1.

E-Coil: (2 required) Weight each:0.41 kg (0.9 lbs.); Fully encapsu-lated with external metal shell;See page 3.400.1.

TO ORDER

SP10-47C

2.112.2

HYDRAFORCE®

3.98101.1

2.4462.0

SHOWN ABOVE WITH E-COILS AND EY CONNECTORS OPTION

4

3

2

1

1

5.74145.7

2.5464.5

Across FlatsTORQUE:

24–26 ft-lbs(32.5–35.3 Nm)

Max.

1.0025.4

INCHMILLIMETRE


1.2531.8

1.2531.8 2.50

63.5

4.43112.5

S1

S2

3.2582.6

0.256.4

2.0050.8

2.8472.1

1.3634.5

0.7418.8

1.9950.5

2

3

4

0.287.1


(5.5–6.8 Nm)Max.

0.7519.1

E-Coil Dia. 1.8446.7

Option"B"

1.50 38.1

Option"M"

Manual Override Knob: Dia.

DIMENSIONSPERFORMANCE (cont’d.)

691000


FLO

W lp

m/g

pm

1382000

2073000

15.1/4

18.9/5

22.7/6

11.4/3

7.6/2

3.8/1

1.0 AMP

0.75 AMP

0.50 AMP


SP10-47C__ - __ __ __ - __ - __ __ __ __ __



OptionNone (Blank)




SAE 6 6TSAE 8 8T



VoltageE-Coil

12 12 VDC24 24 VDC









DESCRIPTIONA proportional solenoid-operated, 4-way, 3-position, spool-type, motor spool, screw-inhydraulic cartridge valve.

OPERATIONWhen de-energized, the SP08-47D blocks flow to ➂ while allowing flow from ➁ to ➀,and from ➃ to ➀. When coil S1 is energized flow is allowed from ➂ to ➃ and from ➁to ➀. When coil S2 is energized flow is allowed from ➂ to ➁ and from ➃ to ➀.




FEATURES• Continuous-duty rated solenoids. • Optional manual override.• Optional coil voltages and terminations. • Industry-common cavity.• Efficient wet-armature construction.• Hardened precision spool and cage for long life.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Designed for good linearity and hysteresis.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: 11.4 lpm (3 gpm) max. (see performance chart); Flow rate is based on 50%

duty cycle and coil temperature of 20°C (140°F). Consult factory if higher dutycycle and coil temperatures are anticipated.



of nominal voltageFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation Recommendation: When possible, the valve should be mounted below




SP08-47D Spool, 4-Way, 3-Position, “Motor Spool”

SYMBOLSUSASI:

ISO:

2.120.1


10.4/150

6.9/100

3.5/50

3.81

7.52

11.43

15.14

FLOW lpm/gpmPR

ES

SU

RE

DR

OP

bar

/psi


INLET

OUTLET

7.5/2

11.4/3

15.1/4

3.8/1

01.0 1.00.5 0.50


FLO

W lp

m/g

pm


E-Coil

E-Coil

Std. Coil Std. Coil



MATERIALS





TO ORDER

SP08-47D

2.120.2

HYDRAFORCE®

2.9274.2

E-Coil Dia.

Option "B"1.50 38.1



1.4135.8


(5.5–6.8 Nm)Max.

0.7519.1

1.1328.7

1.2531.8 2.50

63.5

3.3384.7

S1

S2

Across FlatsTORQUE:

16–20 ft-lbs(24.4–27.1 Nm)

Max.

0.8822.2

2.1554.6

4

4.95125.7

2.1153.4



3

2

1

INCHMILLIMETRE

1.1729.7

2.8472.1

3.2582.6

0.256.4

2.0050.8

0.287.1

1.7343.9

0.6015.2

4

2

1

3

Knob: Dia.


691000


FLO

W lp

m/g

pm


1382000

2073000

15.1/4

11.4/3

7.6/2

3.8/1

1.0 AMP

0.75 AMP

0.50 AMP

SP08-47D__ - __ __ __ - __ - __ __ __ __ __



OptionNone (Blank)






VoltageE-Coil

12 12 VDC24 24 VDC









DESCRIPTIONA proportional solenoid-operated, 4-way, 3-position, spool-type, motor spool, screw-inhydraulic cartridge valve with lower maximum flow rate of 7.6 lpm (2 gpm).

OPERATIONWhen de-energized, the SP08-47DL blocks flow to ➂ while allowing flow from ➁ to ➀,and from ➃ to ➀. When coil S1 is energized flow is allowed from ➂ to ➃ and from ➁to ➀. When coil S2 is energized flow is allowed from ➂ to ➁ and from ➃ to ➀.




FEATURES• Continuous-duty rated solenoids. • Optional manual override.• Optional coil voltages and terminations. • Industry-common cavity.• Efficient wet-armature construction.• Hardened precision spool and cage for long life.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Designed for good linearity and hysteresis.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: 7.6 lpm (2 gpm) max. (see performance chart); Flow rate is based on 50% duty

cycle and coil temperature of 20°C (140°F). Consult factory if higher duty cycle andcoil temperatures are anticipated.



of nominal voltageFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation Recommendation: When possible, the valve should be mounted below




SP08-47DL Spool, 4-Way, 3-Position, “Motor Spool”

SYMBOLSUSASI:

ISO:

2.121.1


10.4/150

6.9/100

3.5/50

3.81.0

1.90.5

7.62.0

5.71.5

FLOW lpm/gpmPR

ES

SU

RE

DR

OP

bar

/psi


3 to 2or 3 to 4

2 to 1or 4 to 1

3.8/1.0

5.7/1.5

7.6/2.0

9.5/2.5

1.9/0.5

01.0 1.00.5 0.50

AMPERAGE with 12 VDC System

FLO

W lp

m/g

pm

S1 - Top Coil S2 - Bottom Coil



MATERIALS


Standard Ported Body: Weight:0.18 kg. (0.40 lbs.); Anodizedhigh-strength 6061 T6 aluminumalloy, rated to 240 bar (3500psi); See page 8.008.1. Ductileiron and steel bodies available;dimensions may differ; consultfactory.



TO ORDER

SP08-47DL

2.121.2

HYDRAFORCE®

2.9274.2

E-Coil Dia.

Option "B"1.50 38.1



1.4135.8


(5.5–6.8 Nm)Max.

0.7519.1

1.1328.7

1.2531.8 2.50

63.5

3.3384.7

S1

S2

Across FlatsTORQUE:

16–20 ft-lbs(24.4–27.1 Nm)

Max.

0.8822.2

2.1554.6

4

4.95125.7

2.1153.4



3

2

1

INCHMILLIMETRE

1.1729.7

2.8472.1

3.2582.6

0.256.4

2.0050.8

0.287.1

1.7343.9

0.6015.2

4

2

1

3

Knob: Dia.


691000


FLO

W lp

m/g

pm


1382000

2073000

7.6/2.0

9.5/2.5

5.7/1.5

3.8/1.0

1.9/0.5

1.0 AMP

0.75 AMP

0.50 AMP

SP08-47DL__ - __ __ __ - __ - __ __ __ __ __



OptionNone (Blank)






VoltageE-Coil

12 12 VDC24 24 VDC









Low Flow Version

DESCRIPTIONA proportional solenoid-operated, 4-way, 3-position, spool-type, motor spool, screw-inhydraulic cartridge valve.

OPERATIONWhen de-energized, the SP10-47D blocks flow to ➂ while allowing flow from ➁ to ➀,and from ➃ to ➀. When coil S1 is energized flow is allowed from ➂ to ➃ and from ➁to ➀. When coil S2 is energized flow is allowed from ➂ to ➁ and from ➃ to port ➀.




FEATURES• Continuous-duty rated solenoids.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Optional manual override.• Industry-common cavity.• Designed for good linearity and hysteresis.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: 22.7 lpm (6 gpm) max. (see performance chart)Internal Leakage: 246 cc/minute (15 cu. in./minute) max. per side

at 207 bar (3000 psi)Hysteresis: Less than 7%Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Standard Coils and E-Coils: Continuous up to 115%




Cavity: VC10-4; See page 9.110.1; Cavity Tool: CT10-4XX; See page 8.600.1Seal Kit: SK10-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180Coil Spacer: Part No. 4539700For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.


SP10-47D Spool, 4-Way, 3-Position, “Motor Spool”

SYMBOLSUSASI:

ISO:

2.122.1


10.4/150

6.9/100

3.5/50

3.81

7.52

11.43

15.14

18.95

22.76

FLOW lpm/gpmPR

ES

SU

RE

DR

OP

bar

/psi


INLET

OUTLET

15.1/4

22.7/6

7.5/2

01.0 1.00.5 0.50


FLO

W lp

m/g

pm


E-Coil

Std. Coil

E-Coil

Std. Coil



MATERIALS

Cartridge: Weight: 0.30 kg.(0.65 lbs.) Steel with hardenedwork surfaces. Zinc-platedexposed surfaces. Buna NO-rings and single-turn polyesterelastomer back-ups standard.


Standard Coil: (2 required) Weighteach: 0.27 kg. (0.60 lbs.);Unitized thermoplastic encapsu-lated, Class H high temperaturemagnetwire; See page 3.200.1.

E-Coil: (2 required) Weight each:0.41 kg (0.9 lbs.); Fully encapsu-lated with external metal shell;See page 3.400.1.

TO ORDER

SP10-47D

2.122.2

HYDRAFORCE®

3.98101.1

2.4462.0

SHOWN ABOVE WITH E-COILS AND EY CONNECTORS OPTION

4

3

2

1

1

5.74145.7

2.5464.5

Across FlatsTORQUE:

24–26 ft-lbs(32.5–35.3 Nm)

Max.

1.0025.4

INCHMILLIMETRE


1.2531.8

1.2531.8 2.50

63.5

4.43112.5

S1

S2

3.2582.6

0.256.4

2.0050.8

2.8472.1

1.3634.5

0.7418.8

1.9950.5

2

3

4

0.287.1


(5.5–6.8 Nm)Max.

0.7519.1

E-Coil Dia. 1.8446.7

Option"B"

1.50 38.1

Option"M"

Manual Override Knob: Dia.


691000


FLO

W lp

m/g

pm

1382000

2073000

15.1/4

18.9/5

22.7/6

26.5/7

11.4/3

7.6/2

3.8/1

1.1 AMP

0.85 AMP

0.60 AMP


SP10-47D__ - __ __ __ - __ - __ __ __ __ __



OptionNone (Blank)




SAE 6 6TSAE 8 8T



VoltageE-Coil

12 12 VDC24 24 VDC









DESCRIPTIONA solenoid-operated, 5-way, 3-position, proportional, screw-in hydraulic cartridge valve with integral load-sense port.

OPERATIONWhen de-energized, the SP10-57C blocks fl ow to all ports. When coil #1 is energized, fl ow is allowed from ➄ to ➁, and from ➃ to ➂. When coil #2 is energized, fl ow is allowed from ➄ to ➃, and from ➁ to ➂. Load sense is connected to port ➄ when the spool is in shifted positions.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations• Cartridges are voltage interchangeable.• Optional manual override.• Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 250 bar (3625 psi) with standard Buna N sealsFlow: 22.7 lpm (6 gpm) max. See performance chartInternal Leakage: 246 cc/minute (15 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1; Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-coils: Part No. 4539700

SYMBOLS

2.132.1

USASI:

ISO:


5

4

3

2

1


15.1/4

22.7/6

7.5/2

3.8/1

11.4/3

18.9/5

01.0 1.0 1.51.5 0.5 0.50


FLO

W lp

m/g

pm

Top Coil

Performance with 12 VDC Coilsand 10.3 bar/150 psi inline compensator

(for other voltages consult factory)Bottom Coil


17.2/250

15.5/225

13.8/200

12.1/175

10.3/150

8.6/125

6.9/100

3.4/50

5.2/75

1.7/25

3.81

7.62

11.43

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

32 cSt/150 sus oil at 40°C➃ to ➂ or ➁ to ➂ at 100% current, S1 or S2 energized: ————➄ to ➁ or ➄ to ➃ at 100% current, S1 or S2 energized: - - - - - - -

SP10-57C Spool, 5-Way, 3-Position . . .

HYDRAFORCE.com®


RP



DIMENSIONS

SP10-57C

2.132.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.

TORQUE:5–7 ft-lbs (6.8–9.5 Nm)max.

1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS

691000


FLO

W lp

m/g

pm

1382000

2073000

15.1/4

18.9/5

22.7/6

11.4/3

7.6/2

3.8/1

1.0 AMP

0.75 AMP

0.50 AMP


PERFORMANCE (Continued)

for Load Sense Applications

®HYDRAFORCE

HYDRAFORCE.com®

SP10-57C__ - __ __ __ - __ - __ __ __ __ __

TO ORDER


Termination (VDC) Std. Coil DS Dual Spades DG DIN 43650 DL Leadwires (2) DL/W Leads w/Weatherpak®

Connectors DR Deutsch DT04-2P

Termination (VDC) E-Coil ER Deutsch DT04-2P (IP69K Rated) EY Metri-Pack® 150 (IP69K Rated)


E-Coil 10 10 VDC 12 12 VDC 20 20 VDC 24 24 VDC

Voltage Std. Coil 0 Less Coil** 10 10 VDC†

12 12 VDC 20 20 VDC 24 24 VDC **Includes Std. Coil Nut

† DS, DW or DL terminations only.

MATERIALS


Standard Ported Body: Weight: 0.41 kg. (0.85 lbs.); Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi); Ductile iron bodies available; dimensions may differ. See page 8.010.1.

Standard Coil: Weight each: 0.27 kg. (0.60 lbs.); Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1

E-Coil: Weight each: 0.41 kg. (0.9 lbs.); Perfect wound, fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors. See page 3.400.1 for all E-Coil retrofi t applications.

Porting Cartridge Only 0 SAE 6 6T SAE 8 8T

Option None (Blank)

Manual Override B Manual Override M

For Manual Override optionssee page 1.001.1

RP



DESCRIPTIONA solenoid-operated, fi ve-way, three-position, proportional, screw-in hydraulic cartridge valve with integral load-sense port.

OPERATIONWhen de-energized, the SP08-57D blocks fl ow at ➄ while allowing fl ow from both ➁ and ➃ to ➂. When coil #1 is energized, fl ow is allowed from ➄ to ➁, and from ➃ to ➂. When coil #2 is energized, fl ow is allowed from ➄ to ➃, and from ➁ to ➂. Load sense is connected to port ➄ when the spool is in shifted positions.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations• Cartridges are voltage interchangeable.• Compact size; Manual override options.• Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 241 bar (3500 psi) with standard Buna N sealsFlow: 9.5 lpm (2.5 gpm); see performance chartsInternal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.2 amps at 12 VDC;

0.13 amps at 115 VAC (full wave rectifi ed). E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDC

Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC08-5; See page 9.108.1; Cavity Tool: CT08-5XX; See page 8.600.1Seal Kit: SK08-5X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer: Part No. 4534720

SYMBOL

2.134.1




SP08-57D Spool, 5-Way, 3-Position . . .

HYDRAFORCE.com®

9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

CURRENT amps

FLO

W lp

m/g

pm


Flow vs. CurrentTypical Performance

Coil S1

Coil S2

34.5/500

31.0/450

27.6/400

24.1/350

20.7/300

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Differential Pressure vs. Flowat I-Max. with No Load; Port ➄ to ➂


1.90.5

3.81.0

5.71.5

7.62.0

9.52.5

11.43.0

13.33.5

15.14.0

5 to 4

5 to 2

4 to 3

2 to 3

RP



DIMENSIONS

SP08-57D

2.134.2



®HYDRAFORCE

HYDRAFORCE.com®

SV08-57D__ - __ __ __ - __ - __ __ __ __ __

TO ORDER










MATERIALS



Cartridge: Weight: 0.15 kg. (0.34 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces; Buna N O-rings and back-ups standard.


Standard Coil: Weight each: 0.11 kg. (0.25 lbs.); Unitized thermoplastic encapsulated, Class H high tempera-ture magnetwire. See page 3.200.1

E-Coil: Weight: 0.14 kg. (0.3 lbs.); Perfect wound, fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors. See page 3.400.1 for all E-Coil retrofi t applications.

0.8822.2

0.7519.1

0.6516.5

1.2331.2

E-CoilView

StandardCoil View

4.95125.7

20 ft-lbs (27.2 Nm) max.

5 ft-lbs (6.8 Nm) max.

4.05102

2.7168.7 2.291

58.2

1.17229.8

0.6115.5

1.73144.0

3.2582.6

0.3448.74

4.05102

3.62592.1

2.0050.8

1.4035.6

1.27032.3

0.1884.8

1.41DIA.

35.8

‘B’

‘M’Option

Option

3.3885.9

Option None (Blank)



Flow varies with manual override options; consult factory for details.

18.9/5.0

17.0/4.5

15.1/4.0

13.2/3.5

11.4/3.0

9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

PRESSURE bar/psi

FLO

W l

pm/g

pm

Pressure Response; Coil S1No Load; Port ➄ to ➂

34500

1.0 A

0.8 A

0.6 A

691000

1031500

1382000

1722500

2073000

15.1/4.0

13.2/3.5

11.4/3.0

9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

PRESSURE bar/psi

FLO

W l

pm/g

pm

Pressure Response; Coil S2No Load; Port ➄ to ➂

34500

1.0 A

0.8 A

0.6 A

691000

1031500

1382000

1722500

2073000

RP



DESCRIPTIONA solenoid-operated, 5-way, 3-position, proportional, screw-in hydraulic cartridgevalve with integral load-sense port.

OPERATIONWhen de-energized, the SP10-57D blocks flow at ➄ while allowing flow from both ➁and ➃ to ➂. When coil #1 is energized, flow is allowed from ➄ to ➁, and from ➃ to ➂.When coil #2 is energized, flow is allowed from ➄ to ➃, and from ➁ to ➂. Load senseis connected to port ➄ when the spool is in shifted positions.


FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional manual override.• Optional waterproof E-Coils rated up to IP69K.• Cartridges are voltage interchangeable.


7.4 to 420 cSt (50 to 2000 sus)Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1; Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-Coils: Part No. 4539700

SYMBOLS

2.136.1

USASI:

ISO:


5

4

3

2

1




15.1/4

22.7/6

7.5/2

3.8/1

11.4/3

18.9/5

01.0 1.00.5 0.50


FLO

W lp

m/g

pm



(for other voltages consult factory)17.2/250

15.5/225

13.8/200

12.1/175

10.3/150

8.6/125

6.9/100

3.4/50

5.2/75

1.7/25

3.81

7.62

11.43

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi



DIMENSIONS

SP10-57D

2.136.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.


1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS

HYDRAFORCE®

691000


FLO

W lp

m/g

pm

1382000

2073000

15.1/4

18.9/5

22.7/6

26.5/7

11.4/3

7.6/2

3.8/1

1.1 AMP

0.85 AMP

0.60 AMP



MATERIALS TO ORDER

SP10-57D__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T










Cartridge: Weight: 0.36 kg. (0.80 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces.Buna N O-rings and polyesterelastomer back-up standard.

Standard Ported Body: Weight:0.41 kg. (0.85 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.010.1. Steel and Ductile Ironbodies available, dimensions maydiffer, consult factory.

Standard Coils: Weight each: 0.27 kg.(0.60 lbs.); Unitized thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

E-Coils: Weight each: 0.41 kg. (0.9lbs.); Fully encapsulated with ruggedexternal metal shell; Rated up toIP69K with integral connectors.

VoltageStd. Coil

0 Less Coil** 10 10 VDC†

12 12 VDC 20 20 VDC 24 24 VDC**Includes coil nut and coil spacer† DS, DW or DL

terminations only

E-Coil10 10 VDC12 12 VDC20 20 VDC24 24 VDC

OptionNone (Blank)



DESCRIPTIONA solenoid-operated, 5-way, 3-position, proportional, screw-in hydraulic cartridgevalve with integral brake release port.

OPERATIONWhen de-energized, the SP10-58D allows flow between ➃, ➂, ➁, and ➀. When coil#1 is energized, flow is allowed from ➄ to ➁, and from ➃ to ➂. When coil #2 isenergized, flow is allowed from ➄ to ➃, and from ➁ to ➂. Load sense is connected toport ➄ when the spool is in shifted positions.


FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional manual override.• Optional waterproof E-Coils rated up to IP69K.• Cartridges are voltage interchangeable.


7.4 to 420 cSt (50 to 2000 sus)Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1; Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-coils: Part No. 4539700

SYMBOLS

2.146.1

USASI:

ISO:


5

4

3

2

1



15.1/4

18.9/5

7.5/2

3.8/1

11.4/3

22.7/6

00.81.0 0.6 0.8 1.21.2 0.4 0.2 0.40.2 0.6 1.00


FLO

W lp

m/g

pm

Bottom Coil


(for other voltages consult factory)

Top Coil


17.2/250

15.5/225

13.8/200

12.1/175

10.3/150

8.6/125

6.9/100

3.4/50

5.2/75

1.7/25

3.81

7.62

11.43

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi



DIMENSIONS

SP10-58D

2.146.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.


1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS

HYDRAFORCE®

691000


FLO

W lp

m/g

pm

1382000

2073000

15.1/4

18.9/5

22.7/6

26.5/7

11.4/3

7.6/2

3.8/1

1.1 AMP

0.85 AMP

0.60 AMP



for Brake Release Applications

MATERIALS TO ORDER

SP10-58D__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T










Cartridge: Weight: 0.36 kg. (0.80 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces.Buna N O-rings and polyesterelastomer back-up standard.

Standard Ported Body: Weight:0.41 kg. (0.85 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.010.1. Steel and Ductile Ironbodies available, dimensions maydiffer, consult factory.

Standard Coils: Weight each: 0.27 kg.(0.60 lbs.); Unitized thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

E-Coils: Weight each: 0.41 kg. (0.9lbs.); Fully encapsulated with ruggedexternal metal shell; Rated up toIP69K with integral connectors.

VoltageStd. Coil

0 Less Coil** 10 10 VDC†

12 12 VDC 20 20 VDC 24 24 VDC**Includes coil nut and coil spacer† DS, DW or DL

terminations only

E-Coil10 10 VDC12 12 VDC20 20 VDC24 24 VDC

OptionNone (Blank)


DESCRIPTIONA solenoid-operated, normally-closed, proportional, poppet-type, screw-in hydraulic cartridge valve incorporating an integral load-sense pressure port with isolation check.

OPERATIONWhen de-energized, the SPCL10-30 blocks flow at all ports. When energized, proportionally-regulated flow is allowed from 3 to 1 with a check-isolated load-sense signal supplied at 2. Reverse flow is not allowed from 1 to 3.

Note: When using this valve in bridge circuits, seals should not be used on the pilot pistons of the pilot-operated check valves. This is to avoid trapping oil which would keep the pilot-operated check valve open.

Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Industry-common cavity. • Efficient wet-armature construction.• Continuous-duty rated coils. • Optional waterproof E-Coils rated up to IP69K.• Reduce manifold space claim.

RATINGSOperating Pressure: 250 bar (3625 psi); Holding Pressure at 1: 350 bar (5000 psi)Internal Leakage: Ports 1 and 3: 5 drops/minute max. at 250 bar (3625 psi)

Port 2: 10 drops/minute max. at 250 bar (3625 psi)Operating Temperature: -40° to 100°C (-40° to 212° F) with standard Buna N seals;

-26° to 204°C (-15° to 400°F) with Fluorocarbon seals;-54°C to 107°C (-65°F to 225°F) with Polyurethane seals

Coil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard D-Coil: 1.67 amps at 12 VDC;

0.18 amps at 115 VAC (full wave rectified). E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC

Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Installation: No restrictions; See page 9.020.1; Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Cavity: VC10-3, Variation “B”; See page 9.110.1Cavity Tool: CT10-3xx; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400

SPCL10-30 Poppet, 3-Port, Normally Closed

SYMBOL

2.040.1


HYDRAFORCE.com®


ISO:

Expanded:

7.6/2

15.1/4

22.7/6

30.3/8

68.1/18

60.6/16

53.0/14

45.4/12

37.9/10

75.7/20

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:

% of Max. Control Current:

FLO

W lp

m/g

pm

FLOW vs. CURRENT16 bar/230 psi – – –; 35 bar/500 psi ——

Ranges Shaded

18.9/5

37.9/10

56.8/15

75.7/20

170.3/45

151.4/40

132.5/35

113.6/30

94.6/25

189.2/50

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm


Ranges Shaded

U.S. Patent 7,921,880


RP


DIMENSIONS

SPCL10-30

2.040.2

TO ORDER

Cartridge: Weight: 0.2 kg. (0.44 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-rings and polyester elastomer back-up standard.

Standard D-Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermoplas-tic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. Note: See page 3.400.1 for all E-Coil retrofit applications.

MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®

1.0025.4

1.6241.1

1.84DIA.

46.7

E-CoilView

3.50


(32.5–35.3 Nm)

88.9

0.8722.1

1.4837.6

2.3259.0

D-Coil View

TORQUE5 – 7 ft-lb.(6.8 Nm max.)

ManualOverride

J

ManualOverride M, or Y

to 0.5A - - - - - ; 0.75A – – – –1.0A — — —; 1.2A ———32 cSt/150 sus oil at 40°C

241/3500

138/2000

172/2500

207/3000

103/1500

69/1000

34.5/500

22.76

45.412

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

11.43

34.19

to at 1.2A Current32 cSt/150 sus oil at 40°C

2.8/40

2.1/30

1.4/20

0.7/10

0.760.2

1.520.4

1.900.5

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

0.380.1

1.140.3


U.S. Patent 7,921,880


SPCL10-30__ - __ __ __ - __ - __ __ __ __ __

Porting

Cartridge Only 0


Voltage 0 Less Coil** 12 12 VDC 20 20 VDC† 24 24 VDC**Includes D-Coil Nut


Coil Termination E-Coil D-CoilDeutsch DT04-2P ER (IP69K) DR (IP65)Metri-Pack® 150 EY (IP69K) DY (IP65)Dual Lead Wires EL (IP69K) DL (IP65)Amp Jr. Timer EJ (IP67) —DIN 43650 EG (IP65) DG (IP65)Dual Spades — DS (IP65)

Option None (Blank) Manual Override M Manual Override Y Manual Override J



RP



DESCRIPTIONA solenoid-operated, 3-port, normally-closed, proportional, poppet-type, screw-in hydraulic cartridge valve for low-leakage blocking and load-holding applications.

OPERATIONWhen the SPCL16-30 is energized, the poppet lifts to allow flow from port 3 to ports 1 and 2. Flow at port 2 is typical for load sensing applications and includes a check valve for isolation.


RATINGSOperating Pressure: Maximum: 250 bar (3625 psi); Minimum: 2.4 bar (35 psi)Flow Rating: up to 152 lpm (40 gpm); see performance chartsInternal Leakage: Ports 1 and 3: 5 drops/minute max. at 250 bar (3625 psi)



Valve Inductance: 173.3 mH at 1.2A (Max. Control Current)Threshold Current: 0.40A to 0.60AHysteresis: Less than 10% of maximum flow at 1.2A (Max. Control Current)Dither Frequency: 100 Hz recommendedInstallation: No restrictions; See page 9.020.1; Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Cavity: VC16-3SPCL; See page 9.116.1Cavity Tool: CT16-3SPCL; See page 8.600.1Seal Kit: SK16-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400


SYMBOL

2.041.1


HYDRAFORCE.com®


U.S. Patent 7,921,880

ISO:

Expanded:

19/5

38/10

57/15

76/20

151/40

132/35

113/30

95/25

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm

FLOW vs. CURRENT; Ports 3 to 1Tested with EC16-32-160 – – –

34.5 bar/500 psi Inlet, Tested with EV20-S34 ——

FLOW vs. CURRENT; Ports 3 to 1103 bar/1500 psi Inlet – – –; 207 bar/3000 psi Inlet ——

Tested with EV20-S34

38/10

76/20

113/30

151/40

341/90

302/80

265/70

227/60

190/50

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm

Performance info. continued on next page.


RP


DIMENSIONS

SPCL16-30

2.041.2

TO ORDER




MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®

2.4361.8

0.8722.1

1.4837.6

0.75 (19.0)ACROSS FLATS

COIL MUST BE INSTALLEDWITH LETTERING UP

3.9098.9

E-Coil10-Size

D-Coil 10-Size

1.6241.1

1.84DIA.

46.7

TORQUE5–7 ft-lbs

(6.8–9.5 Nm)



(62.4–73.2 Nm)


U.S. Patent 7,921,880


Ports 3 to 10.6A - - - - - ; 0.75A – – – –1.0A — — —; 1.2A ———

32 cSt/150 sus oil at 40°C34.5/500

20.7/300

27.6/400

24.1/350

31.0/450

17.2/250

13.8/200

10.3/150

3.4/50

6.9/100

60.616

121.332

151.640

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

30.38

100.024

2.8/40

2.1/30

1.4/20

0.7/10

1.520.4

3.030.8

3.791.0

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

0.760.2

2.270.6

Ports 3 to 2 at 1.2A32 cSt/150 sus oil at 40°C

SPCL16-30 - __ __ __ - __ - __ __ __ __ __

Porting

Cartridge Only 0





RP



DESCRIPTIONA solenoid-operated, normally-closed, proportional, poppet-type screw-in hydraulic cartridge valve providing an integral, non-isolated load signal to pilot counterbalance or other control valves in bridge circuit applications.

OPERATIONWhen de-energized, the SPCL10-32 blocks flow at 1 and 3, while allowing the port 2 load signal to bleed to the low-pressure side of the circuit. When energized, proportionally-controlled flow is allowed from 3 to 1 with a load signal supplied at 2. Reverse flow is not allowed from 1 to 3.

Note: When using this valve in bridge circuits, seals should not be used on the pilot pistons of the pilot-operated check valves. This is to avoid trapping oil which would keep the pilot-operated check valve open.

Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.


RATINGSOperating Pressure: 250 bar (3625 psi); Holding Pressure at 1: 350 bar (5000 psi)Internal Leakage: Ports 1 and 3: 5 drops/minute max. at 250 bar (3625 psi)Operating Fluid Temperature: -40 to 121°C with Buna N seals;

-35 to 204°C with Fluorocarbon seals; -54 to 107°C with Polyurethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard D-Coil: 1.67 amps at 12 VDC;

0.18 amps at 115 VAC (full wave rectified). E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC

Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Installation: No restrictions; See page 9.020.1; Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Cavity: VC10-3, Variation “B”; See page 9.110.1Cavity Tool: CT10-3XX; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400


SYMBOL

2.042.1


HYDRAFORCE.com®


7.6/2

15.1/4

22.7/6

30.3/8

68.1/18

60.6/16

53.0/14

45.4/12

37.9/10

75.7/20

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm


Ranges Shaded

18.9/5

37.9/10

56.8/15

75.7/20

170.3/45

151.4/40

132.5/35

113.6/30

94.6/25

189.2/50

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm


Ranges Shaded

ISO:

Expanded:

U.S. Patent 7,921,880


RP


DIMENSIONS

SPCL10-32

2.042.2

TO ORDER




MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®

1.0025.4

1.6241.1

1.84DIA.

46.7

E-CoilView

3.50


(32.5–35.3 Nm)

88.9

0.8722.1

1.4837.6

2.3259.0

D-Coil View

TORQUE5 – 7 ft-lb.(6.8 Nm max.)

ManualOverride

J

ManualOverride M, or Y

to 0.5A - - - - - ; 0.75A – – – –1.0A — — —; 1.2A ———32 cSt/150 sus oil at 40°C

241/3500

138/2000

172/2500

207/3000

103/1500

69/1000

34.5/500

22.76

45.412

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

11.43

34.19

to at 1.2A Current32 cSt/150 sus oil at 40°C

0.83/12

0.62/9

0.41/6

0.21/3

0.760.2

1.520.4

1.900.5

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

0.380.1

1.140.3


U.S. Patent 7,921,880


SPCL10-32__ - __ __ __ - __ - __ __ __ __ __

Porting

Cartridge Only 0





Option None (Blank) Manual Override M Manual Override Y Manual Override J




RP



OPERATIONWhen the SPCL16-32 is energized, the poppet lifts to allow flow from port 3 to ports 1 and 2. Flow at port 2 is typical for load sensing applications.








SYMBOL

2.043.1


HYDRAFORCE.com®


ISO:

Expanded:

19/5

38/10

57/15

76/20

151/40

132/35

113/30

95/25

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm





38/10

76/20

113/30

151/40

341/90

302/80

265/70

227/60

190/50

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm


U.S. Patent 7,921,880


RP


DIMENSIONS

SPCL16-32

2.043.2

TO ORDER




MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®



Ports 3 to 10.6A - - - - - ; 0.75A – – – –1.0A — — —; 1.2A ———

32 cSt/150 sus oil at 40°C34.5/500

20.7/300

27.6/400

24.1/350

31.0/450

17.2/250

13.8/200

10.3/150

3.4/50

6.9/100

60.616

121.332

151.640

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

30.38

100.024

2.8/40

2.1/30

1.4/20

0.7/10

1.520.4

3.030.8

3.791.0

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

0.760.2

2.270.6

Ports 3 to 2 at 1.2A32 cSt/150 sus oil at 40°C

SPCL16-32 - __ __ __ - __ - __ __ __ __ __

Porting

Cartridge Only 0





2.4361.8

0.8722.1

1.4837.6



3.9098.9

E-Coil10-Size

D-Coil 10-Size

1.6241.1

1.84DIA.

46.7

TORQUE5–7 ft-lbs

(6.8–9.5 Nm)



(62.4–73.2 Nm)

U.S. Patent 7,921,880

RP




OPERATIONWhen the SPCL16-40 is energized, the poppet lifts to allow flow from port 4 to ports 1, 2, and 3. Flow at ports 2 and 3 is typical for load sensing applications and includes a check valve for isolation.



Ports 2 and 3: 15 drops/minute max. at 250 bar (3625 psi)Operating Temperature: -40° to 100°C (-40° to 212° F) with standard Buna N seals;




SPCL16-40 Poppet, 2-Way, Normally Closed

SYMBOL

2.050.1


HYDRAFORCE.com®


19/5

38/10

57/15

76/20

151/40

132/35

113/30

95/25

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm





38/10

76/20

113/30

151/40

341/90

302/80

265/70

227/60

190/50

0.1 0.2

30 40 50 60 70 80 90 100

0.40.3 0.5 0.8 0.9 1.0 1.1 1.20.6 0.7Amps:


FLO

W lp

m/g

pm



U.S. Patent 7,921,880


RP


DIMENSIONS

SPCL16-40

2.050.2

TO ORDER




MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®


U.S. Patent 7,921,880Ports 4 to 1

0.6A - - - - - ; 0.75A – – – –1.0A — — —; 1.2A ———

32 cSt/150 sus oil at 40°C34.5/500

20.7/300

27.6/400

24.1/350

31.0/450

17.2/250

13.8/200

10.3/150

3.4/50

6.9/100

60.616

121.332

151.640

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

30.38

100.024

2.8/40

2.1/30

1.4/20

0.7/10

1.520.4

3.030.8

3.791.0

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

0.760.2

2.270.6

Ports 4 to 2 and 4 to 3 at 1.2A32 cSt/150 sus oil at 40°C

2.4361.8

0.8722.1

1.4837.6



3.9098.9

E-Coil10-Size

D-Coil 10-Size

1.6241.1

1.84DIA.

46.7

TORQUE5–7 ft-lbs

(6.8–9.5 Nm)



(62.4–73.2 Nm)

SPCL16-40 - __ __ __ - __ - __ __ __ __ __

Porting

Cartridge Only 0





RP



ELECTRO-PROPORTIONAL VALVES—FLOW CONTROLS

PV72-20 Proportional Flow Control Cartridge,

USASI/ISO:

SYMBOLS

2.330.1

PERFORMANCE

20

PERCENT OF MAX. CONTROL CURRENT

FLO

W lp

m/g

pm

Flow vs. CurrentInput Pressure: 240 bar/3500 psi

12V Coil; 110 Hz PWM32 cSt/150 ssu oil at 40°C

40 60 80 100

75.6/20

60/16

45/12

30/8

15/4

@PREG 207 bar/3000 psi

DESCRIPTIONA solenoid-operated, electrically-variable, two-port, pressure-compensated, spool-type, normally closed when de-energized, proportional flow control valve.

OPERATIONThe PV72-20 will regulate flow out of port ➁ regardless of system working pressure.With an increasing current applied to the solenoid, the PV72-20 will increase outputflow.Operation of Manual Override:

To Engage: Turn clockwise approximately 1 turn to reach start point. Continueanother approximately 5 turns to full shift.

To Disengage: Turn counterclockwise approximately 6 turns until positive stopis found.

FEATURES• Excellent linearity and hysteresis

characteristics.• Hardened spool and cage for long life.• Efficient wet armature contsruction.• Optional coil voltages and terminations.

RATINGSOperating Pressure: Port ➀: 240 bar (3500 psi); Port ➁: 207 bar (3000 psi)Regulated Flow Rate: 0 to 56 lpm (0 to 15 gpm)Internal Leakage: .38 lpm (0.1 gpm) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC12-2 Cavity Variation “B”; See page 9.112.1Cavity Tool: CT12-2X-XX; See page 8.600.1Seal Kit: SK12-2X-M; See page 8.650.1

• Cartridges voltage interchangeable.• Unitized, molded coil design.• Coil waterproofing standard.• Manual override option.

ThresholdCurrent

250 ± 100 mA125 ± 50 mA

CoilVoltage12 VDC24 VDC

Max. ControlCurrent

1500 ± 100 mA750 ± 50 mA

691000

PRESSURE DROP bar/psi

FLO

W lp

m/g

pm

Regulated Flow vs. Pressure DropInput Pressure: 240 bar/3500 psi


1382000

2073000

75.6/20

60/16

45/12

30/8

15/4



PWM — 4000144 4000133 4000140


Cartridge: Weight: 0.32 kg. (0.7 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. BunaN O-rings and polyester elastomerback-ups standard.

Standard Ported Body: Weight: .59 kg.(1.3 lbs.); Anodized high-strength6061 T6 aluminum alloy, rated to 240bar (3500 psi); See page 8.012.1.Steel and Ductile Iron bodiesavailable; dimensions may differ;consult factory.

Coil: Weight: 0.32 kg. (0.7 lbs.);Unitized thermoplastic encapsulated,Class H high temperature magnet-wire; See page 3.200.1.

DIMENSIONS

MATERIALS TO ORDER

PV72-20

2.330.2

PV72-20 __ - __ __ __ - __ - __ __ __ __

Voltage0 Less Coil12 12 VDC24 24 VDC

Porting0 Cartridge

Only10T SAE 1012T SAE 1216T SAE 16

Normally Closed

1.2531.8

1.9850.3

1.0627.0

1.1328.6

ACROSS FLATS

ACROSS

FLATS

TORQUE: 10-12 ft-lbs(14-16 Nm)

COIL MUST BEINSTALLED WITHLETTERING UP

MANUALOVERRIDE

OPTION"G"

MANUALOVERRIDE

OPTION"M"

INCHMILLIMETRE

2.9374.4

1.7444.1

0.348.6

0.235.8

0.205.1

1.0626.9

2.5063.5

2.5063.5

3.4387.1

2.4462.0

3.3785.6

1.1830.0 0.90

22.9

TORQUE:30 ft-lbs(40.6 Nm)max.

HYDRAFORCE®



Option(s)None (Blank)

ManualOverride MManual

Overridewith Guard G

Terminations Std. CoilDS Dual SpadesDG DIN 43650DL Leadwires (2)


ConnectorsTerminations E-Coil



USASI/ISO:

SYMBOLS

2.340.1

PERFORMANCE

20


FLO

W lp

m/g

pm

Flow vs. CurrentInput Pressure: 240 bar/3500 psi


40 60 80 100

75.6/20

60/16

45/12

30/8

15/4


DESCRIPTIONA solenoid operated, electrically-variable, two-port, pressure-compensated, spool-type, normally open when de-energized, proportional flow control valve.

OPERATIONThe PV72-21 will regulate flow out of port ➁ regardless of system working pressure.With an increasing current applied to the solenoid, the PV72-21 will decrease outputflow.Operation of Manual Override:




characteristics.• Hardened spool and cage for long life.• Efficient wet armature construction.• Optional coil voltages and terminations.

RATINGSOperating Pressure: Port ➀: 240 bar (3500 psi); Port ➁: 207 bar (3000 psi)Regulated Flow Rate: 56 lpm (15 gpm)Internal Leakage: .38 lpm (0.1 gpm) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC12-2, Cavity Variation “B”; See page 9.112.1Cavity Tool: CT12-2X-XX; See page 8.600.1Seal Kit: SK12-2X-M; See page 8.650.1



ThresholdCurrent

150 ± 100 mA75 ± 50 mA

Max. ControlCurrent

1350 ± 150 mA675 ± 75 mA

691000


FLO

W lp

m/g

pm

Regulated Flow vs. Pressure DropInput Pressure: 240 bar/3500 psi


1382000

2073000

75.6/20

60/16

45/12

30/8

15/4




PWM — 4000144 4000133 4000140



Standard Ported Body: Weight: .59 kg.(1.3 lbs.); Anodized high-strength6061 T6 aluminum alloy, rated to 240bar (3500 psi); See page 8.012.1.Steel and Ductile Iron bodiesavailable; dimensions may differ;consult factory.


MATERIALS TO ORDER

PV72-21

2.340.2

Normally Open

1.2531.8

1.9850.3

1.0627.0

1.1328.6

ACROSS FLATS

ACROSS

FLATS

TORQUE: 10-12 ft-lbs(14-16 Nm)


MANUALOVERRIDE

OPTION"G"

MANUALOVERRIDE

OPTION"M"

INCHMILLIMETRE

2.9374.4

1.7444.1

0.348.6

0.235.8

0.205.1

1.0626.9

2.5063.5

2.5063.5

3.4387.1

2.4462.0

3.3785.6

1.1830.0 0.90

22.9


HYDRAFORCE®

DIMENSIONS

PV72-21 __ - __ __ __ - __ - __ __ __ __

Voltage0 Less Coil

12 12 VDC24 24 VDC

Porting0 Cartridge

Only10T SAE 1012T SAE 1216T SAE 16




ManualOverride M

ManualOverride

with Guard G



Connectors

Terminations E-CoilER Deutsch DT04-2P

(IP69K Rated)

DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally closed when de-energized, proportional flow control valve. It can beused as a priority-type flow regulator with pressure-compensated, regulated andbypass flow. It can also be used as a restrictive-type 2-way, pressure-compensatedflow regulator when the bypass line (port ➁) is blocked.

OPERATIONThe PV08-30 will regulate flow out of port ➂ regardless of system working pressure.With an increasing current applied to the solenoid, the PV08-30 will increase outputflow.

Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving (dead-headed), a small bleed orifice is required atthe priority port (port ➂). Consult factory.

FEATURES• Excellent linearity and hysteresis characteristics.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet armature construction.

RATINGSOperating Pressure: Inlet: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate: Bypass Blocked, Range A: 11.4 lpm (3.0 gpm)

Bypass Blocked, Range B: 5.7 lpm (1.5 gpm)Bypass Open, Range A: 11.4 lpm (3.0 gpm)Bypass Open, Range B: 5.7 lpm (1.5 gpm)

Nominal Input Flow: Bypass Open, Range A: 15.2 lpm (4.0 gpm)Bypass Open, Range B: 7.6 lpm (2.0 gpm)

Maximum Input Flow: Bypass Open, Range A: 22.8 lpm (6.0 gpm)Bypass Open, Range B: 22.8 lpm (6.0 gpm)

Internal Leakage: 100 cc/min. (6 cu. in./min.) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings (Uses EHPR Series Coil; See page 3.200.8)


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC08-3; See page 9.108.1Cavity Tool: CT08-3X-XX; See page 8.600.1Seal Kit: SK08-3X-MM; See page 8.650.1


USASI/ISO:

SYMBOLS

2.370.1

PERFORMANCE

Threshold Current400 ± 100 mA200 ± 50 mA

Coil Voltage12 VDC24 VDC

Max. Control Current1400 ± 150 mA

700 ± 75 mA

2

3

1

20


FLO

W lp

m/g

pm

Nominal Flow vs. Current207 bar/3000 psi; 12V Coil; 200 Hz PWM


40 60 80 100

15.2/4

11.4/3

7.6/2

3.8/1

Range A, 2-Ported or 3-PortedRange B, 2-Ported or 3-Ported

2-Ported:

691000


FLO

W lp

m/g

pm

Regulated Flow vs. Pressure Drop2-Ported; Flow Range A240 bar/3500 psi Inlet


1382000

2073000

2764000

15.2/4

11.4/3

7.6/2

3.8/1

1.5 AMP

1.1 AMP

0.8 AMP

0.4 AMP

691000


FLO

W lp

m/g

pm

Regulated Flow vs. Pressure Drop2-Ported; Flow Range B240 bar/3500 psi Inlet


1382000

2073000

2764000

3.8/1

7.6/2

1.50 AMP

1.10 AMP

0.80 AMP

0.40 AMP




EHPR Series Coil: Weight: 0.32 kg.(0.7 lbs.); Unitized thermoplasticencapsulated, Class H hightemperature magnet-wire;See page 3.200.8.

DIMENSIONS

MATERIALS TO ORDER

PV08-30

2.370.2

PV08-30__ __ - __ __ __ - __ - __ __ __ __


Flow RangeAB

Voltage0 Less Coil

12 12 VDC24 24 VDC

Porting0 Cartridge Only

6T SAE 63B 3/8 in. BSP*


(Required. Refer toPerformance Curves)

Normally Closed

MILLIMETREINCH

31.21.23

15.20.60

53.82.12

66.52.62

50.82.00

29.71.17

6.40.25 7.1

0.28

52.32.06

40.61.60

28.71.13

31.81.25

63.52.50

2 2

33

1

1

0.8822.1ACROSS FLATSTORQUE: 4–5 ft-lbs (7–10 Nm)

0.8822.1ACROSS FLATSTORQUE:

(27.1 Nm)20 ft-lbs

HYDRAFORCE®

TerminationsDS Dual SpadesDG DIN 43650DL Leadwires (2)

DL/W Leads w/Weatherpak

Connectors




0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140



1

2

3


OPERATIONThe PV70-30 will regulate flow out of port ➂ regardless of system working pressure.With an increasing current applied to the solenoid, the PV70-30 will increase outputflow.

Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving, bypass pressure drop will increase unless a smallamount of leakage is provided for the priority port. Consult factory.Operation of Manual Override:


To Disengage: Turn counterclockwise approximately 6 turns to positive stop.


characteristics.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet armature construction.

RATINGSOperating Pressure: Inlet: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate: Bypass Blocked, Range A: 26 lpm (7 gpm)

Bypass Blocked, Range B: 17 lpm (4.5 gpm)Bypass Open, Range A: 30 lpm (8 gpm)Bypass Open, Range B: 17 lpm (4.5 gpm)

Maximum Input Flow: Bypass Open, Range A: 50 lpm (13 gpm)Bypass Open, Range B: 26 lpm (7 gpm)

Internal Leakage: 197 cc/min. (12 cu. in./min.) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings



USASI/ISO:

SYMBOLS

2.372.1

PERFORMANCE


20


FLO

W lp

m/g

pm

Flow vs. Current207 bar/3000 psi; 12V Coil; 200 Hz PWM

32 cSt/150 ssu oil at 40°CRange A, 2-PortedRange A, 3-Ported

Range B, 2-Ported or 3-Ported

40 60 80 100

37.9/10

30.3/8

22.7/6

15.1/4

7.6/2



Max. Control Current1500 ± 200 mA750 ± 100 mA


Performance info. continued on following page.



PWM — 4000144 4000133 4000140


PV70-30Normally Closed

DIMENSIONS

MATERIALS TO ORDER

2.372.2

PV70-30__ __ - __ __ __ - __ - __ __ __ __

Flow RangeAB



6T SAE 68T SAE 82B 1/4 in. BSP*3B 3/8 in. BSP*


(Refer toPerformanceCurves.)

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N

1.0627.0ACROSS FLATS

2.70

1.81

68.6

46.0

0.87 1.8622.1 47.2

MILLIMETREINCH


18.8

53.8

66.5

34.5

7.150.86.4

63.5

31.8

31.8

1.36

2.000.25

2.62

2.12

0.74

2.50

1.25

1.25

0.28

2

3

1

TORQUE: 10–12 ft-lbs (14–16 Nm)

TORQUE: 27 ft-lbs max.(36.7 Nm)

1

2

44.11.74

3

.6717.0

3.3785.6

1.7143.4

2.0953.1

MANUALOVERRIDE

OPTION"G"

MANUAL OVERRIDEOPTION "M"


691000


FLO

W lp

m/g

pm



1382000

2073000

2764000

37.9/10

30.3/8

22.7/6

15.1/4

7.6/2

1.3 AMP

1.0 AMP

0.7 AMP

0.4 AMP

691000


FLO

W lp

m/g

pm



1382000

2073000

2764000

18.9/5

3.8/1

11.4/3

22.7/6

15.1/4

7.6/2

1.25 AMP

1.00 AMP

0.75 AMP

0.50 AMP

HYDRAFORCE®


Standard Ported Body: Weight: 0.36kg. (0.80 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.010.1. Steel and Ductile Ironbodies available; dimensions maydiffer; consult factory.

PV70 Series Coil: Weight: 0.32 kg.(0.7 lbs.); Unitized thermoplasticencapsulated, Class H hightemperature magnet-wire;See page 3.200.7.








Connectors


(IP69K Rated)


1

2

3


OPERATIONThe PV72-30 will regulate flow out of port ➂ regardless of system working pressure.With increasing current applied to the solenoid, the PV72-30 will increase output flow.Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving, bypass pressure drop will increase unless a smallamount of leakage is provided for the priority port. Consult factory.Operation of Manual Override:



FEATURES• Excellent linearity and hysteresis .• Hardened spool and cage for long life.• Efficient wet armature construction.• Optional coil voltages and terminations.

RATINGSOperating Pressure: Port ➀: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate in 3-Port Mode: Range A: 57 lpm (15 gpm)

Range B: 38 lpm (10 gpm)Maximum Input Flow in 3-Port Mode: Range A and B: 114 lpm (30 gpm)Maximum Flow Rate in 2-Port Mode: Range A: 53 lpm (14 gpm)

Range B: 31 lpm (8 gpm)Note: For increased flow capacity in a 2-port flow control, see model PV72-20Internal Leakage: .38 lpm (0.1 gpm) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC12-3; See page 9.112.1; Cavity Tool: CT12-3X-XX; See page 8.600.1Seal Kit: SK12-3X-MM; See page 8.650.1

PERFORMANCE

USASI/ISO:

SYMBOLS

2.374.1





20


FLO

W lp

m/g

pm

40 60 80 100

76/20

60/16

45/12

30/8

15/4

A

B

Flow vs. CurrentInput Flow: 76 lpm/20 gpm

12V Coil; 110 Hz PWM3-Ported —— ; 2 Ported - - - -




Regulated Flow vs. PressureInput Flow: 76 lpm/20 gpm

12V Coil; 110 Hz PWM32 cST/150 ssu oil at 40°C

60/16

76/20

45/12

30/8

15/4FLO

W lp

m/g

pm

Regulated > BypassBypass > RegulatedPRESSURE

2764000

2764000

1382000

0 bar0 psi

1382000

A — B - -


0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140




Standard Ported Body: Weight:1.09 kg. (2.4 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.012.1. Steel and Ductile Ironbodies available; dimensions maydiffer; consult factory.


MATERIALS TO ORDER

2.374.2


10T SAE 1012T SAE 1216T SAE 164B 1/2 in. BSP*6B 3/4 in. BSP*


CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87 1.8622.1 47.2

MILLIMETREINCH

1.2531.8ACROSSFLATS

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1

TORQUE:10–12 ft-lbs (14–16 Nm)

TORQUE: 35 ft-lbs(47.4 Nm)

2

1

3

44.11.74

2.7068.6

.6717.0

3.3785.6

1.5840.1

1.8647.2

max.

MANUALOVERRIDE

OPTION"G"


DIMENSIONS

HYDRAFORCE®

PV72-30__ __ - __ __ __ - __ - __ __ __ __

Flow RangeAB

Voltage0 Less Coil

12 12 VDC24 24 VDC





ManualOverride M

ManualOverride

with Guard G



Connectors


(IP69K Rated)

PV76-30A Proportional Flow Control Cartridge,


OPERATIONThe PV76-30A will regulate flow out of port ➂ regardless of system working pressure.With increasing current applied to the solenoid, output flow will increase.

Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving, bypass pressure drop will increase unless a smallamount of leakage is provided for the priority port. Consult factory.Operation of Manual Override: To Engage: Turn clockwise approximately 1 turn toreach start point. Continue another approximately 5 turns to full shift. To Disengage:Turn counterclockwise approximately 6 turns to positive stop.


RATINGSOperating Pressure: Inlet: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate: Range A: 3-Ported: 94.6 lpm (25.0 gpm)

Range A: 2-Ported: 85.2 lpm (22.5 gpm)Nominal Input Flow: Bypass Open, 3-Ported: 121 lpm (32.0 gpm)Maximum Input Flow: Bypass Open, 3-Ported: 151.4 lpm (40.0 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) at zero currentElectrical: 2 standard voltage ratings



USASI/ISO:

SYMBOLS

2.376.1

PERFORMANCE




3

2

1


2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5

3-WAY VALVERegulated Flow vs. Current

240 bar/3500 psi Inlet207 bar/3000 psi at Port ➂; No Load at Port ➁

12V Coil; 110 Hz PWM32 cSt/150 sus oil at 40°C

PRESSURE bar/psiReg. P > Byp. PByp. P > Reg. P

FLO

W lp

m/g

pm

01382000

1382000

2764000

2764000

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5

3-WAY VALVERegulated Flow vs. Load

240 bar/3500 psi, 121 lpm/32 gpm Inlet12V Coil; 110 Hz PWM


1.60 amp

1.25 amp

1.0 amp

0.7 amp

0.4 amp



PWM — 4000144 4000133 4000140


PV76-30ANormally Closed

DIMENSIONS

MATERIALS TO ORDER

2.376.2

Porting0 Cartridge

Only12T SAE 1216T SAE 16

HYDRAFORCE®


Standard Ported Body: Weight:1.6 kg. (3.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi);See page 8.016.1. Steel and DuctileIron bodies available; dimensionsmay differ; consult factory.


75.12.96

3

3

2 2

1

1

44.11.74

50.82.00

101.64.00

50.31.98

119.94.72

101.03.98

96.83.81

30.01.18

MILLIMETREINCH

25.41.00

8.740.34

4.760.18

54.02.13

111.14.38

127.05.00

92.13.63

38.11.50

ACROSS

FLATS


1.0627.0ACROSS FLATSTORQUE:10–12 ft-lbs (14–16 Nm)

MANUALOVERRIDE

OPTION"G"

MANUALOVERRIDE

OPTION"M"

(continued)PERFORMANCE

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5


240 bar/3500 psi Inlet207 bar/3000 psi at Port ➂



FLO

W lp

m/g

pm

1722500

1031500

2423500

35500

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5

2-WAY VALVERegulated Flow vs. Pressure Drop

240 bar/3500 psi Inlet12V Coil; 110 Hz PWM


1.60 amp

1.25 amp

1.0 amp

0.7 amp

0.4 amp

PV76-30A __ - __ __ __ - __ - __ __ __ __











PV42-M30 Proportional Flow Control Cartridge,

DESCRIPTIONA solenoid-operated, two-stage, three-port, pressure-compensated, spool-type,normally closed when de-energized, proportional flow control valve. It can be used asa priority-type flow regulator with pressure-compensated, regulated and bypass flow.

OPERATIONThe PV42-M30 will regulate flow out of port ➂ regardless of system working pressureat ➂ or at bypass port ➁. Two priority flow ranges are provided for better resolution:Range A for priority flow up to 190 lpm/50 gpm, and Range B for priority flow up to132 lpm/35 gpm. For either range, the input flow at ➀ can be up to 225 lpm/60 gpm.

Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving, bypass pressure drop will increase unless a smallamount of leakage is provided for the priority port. Consult factory.Operation of Manual Override: To Engage: Turn clockwise approximately 3 turns toreach start point. Continue another approximately 2 more turns to full shift. ToDisengage: Turn counterclockwise approximately 5 turns to positive stop.


RATINGSOperating Pressure: Inlet: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate: Range A: 190 lpm (50 gpm)

Range B: 132 lpm (35 gpm)Maximum Input Flow: 225 lpm (60 gpm)Maximum Internal Leakage: 1.52 lpm (0.40 gpm) at zero currentElectrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC42-M3; See page 9.142.1; Cavity Tool: CT42-M3X-XX; See page 8.600.1Seal Kit: SK42-3X-MM; See page 8.650.1

USASI/ISO:

SYMBOLS

2.378.1

PERFORMANCE




3

2

1


2010

Percent of Max. Control Current

FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

228/60

189/50

151/40

114/30

76/20

38/10

Range ARegulated Flow vs. Current207 bar/3000 psi at Port ➂

at 190 lpm/50 gpm Input Flow12V Coil; 110 Hz PWM



FLO

W lp

m/g

pm

01382000

691000

1382000

691000

2073000

2073000

228/60

189/50

151/40

114/30

76/20

38/10

Range A, 3-WayRegulated Flow vs. Load



1.4 amp

0.7 amp

0.9 amp

0.5 amp



PWM — 4000144 4000133 4000140


U.S. Patent6,966,329

PV42-M30Normally Closed

DIMENSIONS

MATERIALS TO ORDER

2.378.2

PV42-M30 __ __ - __ __ __ - __ - __ __ __ __

Voltage0 Less Coil

12 12 VDC24 24 VDC

PortingConsultFactory

HYDRAFORCE®


Ported Body: Consult factory.


116.94.60

110.04.33

MAX

MILLIMETREINCH

MANUALOVERRIDE

OPTIONWITH GUARD

"G"

MANUALOVERRIDE

OPTION"M"

3

2

1


47.61.88

ACROSS

M42 x 2.0 - 6gTHREAD

FLATS

TORQUE:65–75 ft-lbs(88–102 Nm)

79.03.11

90.93.58







2010

Percent of Max. Control Current

FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

151/40

114/30

76/20

38/10

Range BRegulated Flow vs. Current207 bar/3000 psi at Port ➂

at 125 lpm/33 gpm Input Flow12V Coil; 110 Hz PWM



FLO

W lp

m/g

pm

01382000

691000

1382000

691000

2073000

2073000

151/40

114/30

76/20

38/10

Range B, 3-WayRegulated Flow vs. Load


32 cSt/150 sus oil at 40°C1.4 amp

0.7 amp

0.9 amp

0.5 amp


Manual Override MManual Override

with Guard G

Flow RangeUp to 190 lpm

(50 gpm) AUp to 132 lpm

(35 gpm) B

U.S. Patent 6,966,329

DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally open when de-energized, proportional flow control valve. It can beused as a priority-type flow regulator with pressure-compensated, regulated andbypass flow. It can also be used as a restrictive-type 2-way, pressure-compensatedflow regulator when the bypass line (port ➁) is blocked.

OPERATIONThe PV08-31 will regulate flow out of port ➂ regardless of system working pressure.With an increasing current applied to the solenoid, the PV08-31 will decrease outputflow.

Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving (dead-headed), a small bleed orifice is required atthe priority port (port ➂). Consult factory.


RATINGSOperating Pressure: Inlet: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate: Bypass Blocked, Range A: 11.4 lpm (3.0 gpm)

Bypass Blocked, Range B: 5.7 lpm (1.5 gpm)Bypass Open, Range A: 11.4 lpm (3.0 gpm)Bypass Open, Range B: 5.7 lpm (1.5 gpm)

Nominal Input Flow: Bypass Open, Range A: 15.2 lpm (4.0 gpm)Bypass Open, Range B: 7.6 lpm (2.0 gpm)

Maximum Input Flow: Bypass Open, Range A: 22.8 lpm (6.0 gpm)Bypass Open, Range B: 22.8 lpm (6.0 gpm)

Internal Leakage: 100 cc/min. (6 cu. in./min.) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings (Uses EHPR Series Coil; See page 3.200.8)


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC08-3; See page 9.108.1Cavity Tool: CT08-3X-XX; See page 8.600.1Seal Kit: SK08-3X-MM; See page 8.650.1Recommended Electronic Controllers: See page 2.001.1


USASI/ISO:

SYMBOLS

2.380.1

PERFORMANCE




2

3

1

20


FLO

W lp

m/g

pm

Nominal Flow vs. Current207 bar/3000 psi; 12V Coil; 200 Hz PWM

32 cSt/150 ssu oil at 40°CRange A, 2 or 3-PortedRange B, 2 or 3-Ported

40 60 80 100

15.2/4

11.4/3

7.6/2

3.8/1

2-Ported:

691000


FLO

W lp

m/g

pm



1382000

2073000

2764000

15.2/4

11.4/3

7.6/2

3.8/1

0.0 AMP

0.4 AMP

0.8 AMP

1.2 AMP

691000


FLO

W lp

m/g

pm



1382000

2073000

2764000

3.8/1

7.6/20.0 AMP

0.4 AMP

0.8 AMP

1.2 AMP



Standard Ported Body: Weight:0.27 kg. (0.60 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.008.1. Steel and ductile ironbodies available; dimensions maydiffer; consult factory.


DIMENSIONS

MATERIALS TO ORDER

PV08-31

2.380.2

PV08-31__ __ - __ __ __ - __ - __ __ __ __


Flow RangeAB

Voltage0 Less Coil

12 12 VDC24 24 VDC


6T SAE 63B 3/8 in. BSP*


(Required. Refer toPerformance Curves)

Normally Open

MILLIMETREINCH

31.21.23

15.20.60

53.82.12

66.52.62

50.82.00

29.71.17

6.40.25 7.1

0.28

52.32.06

40.61.60

28.71.13

31.81.25

63.52.50

2 2

33

1

1

0.8822.1ACROSS FLATSTORQUE: 4–5 ft-lbs (7–10 Nm)

0.8822.1ACROSS FLATSTORQUE:

(27.1 Nm)20 ft-lbs

HYDRAFORCE®




Connectors




PWM — 4000144 4000133 4000140



1

2

3

DESCRIPTIONA solenoid operated, electrically-variable, three-port, pressure-compensated, spool-type, normally open when de-energized, proportional flow control valve. It can beused as a priority-type flow regulator with pressure-compensated, regulated andbypass flow. It can also be used as a restrictive-type 2-way, pressure-compensatedflow regulator when the bypass line (port ➁) is blocked.

OPERATIONThe PV70-31 will regulate flow out of port ➂ regardless of system working pressure.With an increasing current applied to the solenoid, the PV70-31 will decrease outputflow.

Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving, bypass pressure drop will increase unless a smallamount of leakage is provided for the priority port. Consult factory.Operation of Manual Override:




characteristics.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet armature construction.

RATINGSOperating Pressure: Inlet: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate: Bypass Blocked, Range A: 26 lpm (7 gpm)

Bypass Blocked, Range B: 17 lpm (4.5 gpm)Bypass Open, Range A: 30 lpm (8 gpm)Bypass Open, Range B: 17 lpm (4.5 gpm)

Maximum Input Flow: Bypass Open, Range A: 50 lpm (13 gpm)Bypass Open, Range B: 26 lpm (7 gpm)

Internal Leakage: 197 cc/min. (12 cu. in./min.) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings



USASI/ISO:

SYMBOLS

2.382.1


20


FLO

W lp

m/g

pm

Flow vs. Current207 bar/3000 psi; 12V Coil; 200 Hz PWM

32 cSt/150 ssu oil at 40°CRange A, 2-PortedRange A, 3-PortedRange B, 2-PortedRange B, 3-Ported

40 60 80 100

37.9/10

30.3/8

22.7/6

15.1/4

7.6/2

PERFORMANCE

Performance information continuedon following page.







PWM — 4000144 4000133 4000140


PV70-31Normally Open

DIMENSIONS

MATERIALS TO ORDER

2.382.2

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.70

1.81

68.6

46.0

0.87 1.8622.1 47.2

MILLIMETREINCH


18.8

53.8

66.5

34.5

7.150.86.4

63.5

31.8

31.8

1.36

2.000.25

2.62

2.12

0.74

2.50

1.25

1.25

0.28

2

3

1



1

2

44.11.74

3

.6717.0

3.3785.6

1.7143.4

2.0953.1

MANUALOVERRIDE

OPTION"G"



691000


FLO

W lp

m/g

pm



1382000

2073000

2764000

37.9/10

30.3/8

22.7/6

15.1/4

7.6/2

0.0 AMP

0.5 AMP

0.8 AMP

1.1 AMP

691000


FLO

W lp

m/g

pm



1382000

2073000

2764000

18.9/5

3.8/1

11.4/3

22.7/6

15.1/4

7.6/2

0.0 AMP

0.5 AMP

0.7 AMP

0.9 AMP

1.1 AMP

HYDRAFORCE®




PV70-31__ __ - __ __ __ - __ - __ __ __ __

Flow RangeAB

Voltage0 Less Coil

12 12 VDC24 24 VDC


6T SAE 68T SAE 82B 1/4 in. BSP*3B 3/8 in. BSP*






ManualOverride M

ManualOverride

with Guard G






1

2

3

DESCRIPTIONA solenoid operated, electrically-variable, three-port, pressure-compensated, spool-type, normally open when de-energized, proportional flow control valve. It can beused as a priority-type flow regulator with pressure-compensated, regulated andbypass flow. It can also be used as a restrictive-type 2-way, pressure-compensatedflow regulator when the bypass line (port ➁) is blocked.

OPERATIONThe PV72-31 will regulate flow out of port ➂ regardless of system working pressure.With an increasing current applied to the solenoid, the PV72-31 will decrease outputflow.Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving, bypass pressure drop will increase unless a smallamount of leakage is provided for the priority port. Consult factory.Operation of Manual Override:





RATINGSOperating Pressure: Port ➀: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate in 3-Port Mode: Range A: 53 lpm (14 gpm)

Range B: 38 lpm (10 gpm)Maximum Input Flow in 3-Port Mode: Range A and B: 114 lpm (30 gpm)Maximum Flow Rate in 2-Port Mode: Range A: 42 lpm (11 gpm)

Range B: 31 lpm (8 gpm)Note: For increased flow capacity in a 2-port flow control, see model PV72-21Internal Leakage: .38 lpm (0.1 gpm) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings



USASI/ISO:

SYMBOLS

2.384.1

PERFORMANCE


20


FLO

W lp

m/g

pm

40 60 80 100

76/20

60/16

45/12

30/8

15/4

A

B

Flow vs. CurrentInput Flow: 76 lpm/20 gpm



Regulated Flow vs. PressureInput Flow: 76 lpm/20 gpm

12V Coil; 110 Hz PWM32 cST/150 ssu oil at 40°C

60/16

76/20

45/12

30/8

15/4FLO

W lp

m/g

pm

PREG > PBYPPBYP > PREG

2764000

2764000

1382000

0 bar0 psi

1382000

A — B - -







PWM — 4000144 4000133 4000140



Cartridge: Weight: 0.36 kg. (0.8 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces.Buna N O-rings and polyesterelastomer back-ups standard.



MATERIALS TO ORDER

2.384.2

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87 1.8622.1 47.2

MILLIMETREINCH

1.2531.8ACROSSFLATS

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1



2

1

3

44.11.74

2.7068.6

.6717.0

3.3785.6

1.5840.1

1.8647.2

max.

MANUALOVERRIDE

OPTION"G"


HYDRAFORCE®

DIMENSIONS


10T SAE 1012T SAE 1216T SAE 164B 1/2 in. BSP*6B 3/4 in. BSP*


PV72-31__ __ - __ __ __ - __ - __ __ __ __

Flow RangeAB













DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally open when de-energized, proportional flow control valve. It can beused as a priority-type flow regulator with pressure-compensated, regulated andbypass flow. It can also be used as a restrictive-type 2-way, pressure-compensatedflow regulator when the bypass line (port ➁) is blocked.

OPERATIONThe PV76-31 will regulate flow out of port ➂ regardless of system working pressure.With an increasing current applied to the solenoid, output flow will decrease.

Note: When used as a bypass flow control in applications where the priority flow portwill be blocked by external valving, bypass pressure drop will increase unless a smallamount of leakage is provided for the priority port. Consult factory.Operation of Manual Override: To Engage: Turn clockwise approximately 1 turn toreach start point. Continue another approximately 5 turns to full shift. To Disengage:Turn counterclockwise approximately 6 turns to positive stop.


RATINGSOperating Pressure: Inlet: 240 bar (3500 psi); Ports ➁ and ➂: 207 bar (3000 psi)Regulated Flow Rate: 3-Ported: 75.7 lpm (20.0 gpm)

2-Ported: 79.5 lpm (21.0 gpm)Maximum Input Flow: Bypass Open, 3-Ported: 151.4 lpm (40.0 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) at maximum currentElectrical: 2 standard voltage ratings



USASI/ISO:

SYMBOLS

2.386.1

PERFORMANCE




3

2

1


2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5


240 bar/3500 psi Inlet207 bar/3000 psi at Port ➂; No Load at Port ➁



FLO

W lp

m/g

pm

01382000

1382000

2764000

2764000

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5

3-WAY VALVERegulated Flow vs. Load



0 amp

0.3 amp

0.6 amp

0.9 amp

1.2 amp



PWM — 4000144 4000133 4000140



DIMENSIONS

MATERIALS TO ORDER

2.386.2

(continued)

HYDRAFORCE®


Standard Ported Body: Weight:1.6 kg. (3.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi);See page 8.016.1. Steel and DuctileIron bodies available; dimensionsmay differ; consult factory.


75.12.96

3

3

2 2

1

1

44.11.74

50.82.00

101.64.00

50.31.98

119.94.72

101.03.98

96.83.81

30.01.18

MILLIMETREINCH

25.41.00

8.740.34

4.760.18

54.02.13

111.14.38

127.05.00

92.13.63

38.11.50

ACROSS

FLATS



MANUALOVERRIDE

OPTION"G"

MANUALOVERRIDE

OPTION"M"

PERFORMANCE

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5


240 bar/3500 psi Inlet207 bar/3000 psi at Port ➂



FLO

W lp

m/g

pm

1722500

1031500

2423500

35500

113.5/30

94.6/25

75.7/20

56.8/15

37.9/10

18.9/5

2-WAY VALVERegulated Flow vs. Pressure Drop



0 amp

0.3 amp

0.6 amp

0.9 amp

1.2 amp

Porting0 Cartridge

Only12T SAE 1216T SAE 16

PV76-31__ - __ __ __ - __ - __ __ __ __

Voltage0 Less Coil

12 12 VDC24 24 VDC








Connectors


(IP69K Rated)


USASI/ISO:

SYMBOLS

2.400.1

PERFORMANCE

20.7/300

7.52

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➁ Coil EnergizedThrough Cartridge & Ported Body

32 cSt/150 ssu oil at 40°CNote: Port ➀ is not used.

15.14

22.76

30.28

37.910

45.412

53.014

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

ABC

12

3

1

2

3

DESCRIPTIONA linear solenoid-driven, two-way normally closed, screw-in cartridge valve designedfor use with a pressure compensator to function as an electrically stroked variableflow regulator.

OPERATIONWith increasing electric current, the PV70-33 changes from full closed to full openwith flow from port ➂ to port ➁. Port ➀ is used only to pressure balance the spool andshould be plugged. The proportional valve is intended to function in tandem withstandard HydraForce pressure compensators at pressure differentials of 21 bar (300psid) or less, or alone in variable volume pressure-compensated circuits with loadsense capability.

The valve is designed to work with industry-common controllers which typicallyfeature current capability to 2 amps @ 12 VDC, PWM, and start/stop trim adjustments(I-min./I-max.). Consult factory for details and potential sourcing.

Operation of Manual Override:To Engage: Turn clockwise approximately 1 turn to reach start point. Continue

another approximately 5 turns to full shift.To Disengage: Turn counterclockwise approximately 6 turns to positive stop.


characteristics.• Optional control orifice sizes.• Hardened spool and cage for long life.• Optional coil voltages and terminations.

RATINGSOperating Pressure: 207 bar (3000 psi)Internal Leakage: 197 cc/min. (12 cu. in./min.) fully closed at 207 bar (3000 psi)Electrical: 2 standard voltage ratings

• Efficient wet armature construction.• Cartridges voltage interchangeable.• Unitized, molded coil design.• Coil waterproofing standard.• Manual override option.

ThresholdCurrent (mA)

A & B CRange Range

300 ± 70 360 ± 70150 ± 35 180 ± 35


Max. ControlCurrent (mA)

A & B CRange Range

1500 ± 200 1400 ± 200750 ± 100 700 ± 100






PWM — 4000144 4000133 4000140


DIMENSIONS

MATERIALS TO ORDER

PV70-33

2.400.2

Normally Closed

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.70

1.81

68.6

46.0

0.87 1.8622.1 47.2

MILLIMETREINCH


18.8

53.8

66.5

34.5

7.1

50.86.4

63.5

31.8

31.8

1.36

2.00Plugged

0.25

2.62

2.12

0.74

2.50

1.25

1.25

0.28

2

3

1



1

2

44.11.74

3

.6717.0

3.3785.6

1.7143.4

2.0953.1

MANUALOVERRIDE

OPTION"G"


HYDRAFORCE®




Port Plug: For SAE 6 Port: 6103006For SAE 8 Port: 6103008;See page 8.500.1.

PV70-33__ __ - __ __ __ - __ - __ __ __ __

Flow RangeABC

Voltage0 Less Coil

12 12 VDC24 24 VDC

Porting0 Cartridge

Only6T SAE 68T SAE 82B 1/4 in. BSP*3B 3/8 in. BSP*






ManualOverride M

ManualOverride

with Guard G



Connectors


(IP69K Rated)

2.401.1

USASI:

SYMBOLS

ISO:

DESCRIPTIONA pressure-compensated electrically-variable two-port flow regulator that is normallyclosed when de-energized. This combination valve uses a PV70-33x proportionalcartridge and an EC10-30 compensator.

OPERATIONThis proportional valve/compensator package will regulate flow out of port ➁,regardless of system working pressure. With an increasing current applied to thesolenoid, the PFR70-33x-E will increase output flow.



RATINGSOperating Pressure: 207 bar (3000 psi)Internal Leakage: 410 cc/min. (25 cu. in./min.) fully closed at 207 bar (3000 psi) out

port ➁.Electrical: 2 standard voltage ratings

PFR70-33x-E Proportional Flow Regulator, N.C.,

37.9/10

CURRENT amp

FLO

W lp

m/g

pm

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

Flow vs. Current (207 bar/3000 psi Load)PV70-33B with EC10-3011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -

100 Hz Dither37.9/10

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (207 bar/3000 psi Load)PV70-33A with EC10-3011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -

100 Hz Dither

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

PERFORMANCE CURVES Regulated Flow Delivered Out Port ➁:24 Volt coil used; 130 Hz dither; PWM controller. For 12 volt coils, double the current (amp) values shown.

• Efficient wet armature construction.• Cartridges voltage interchangeable.• Unitized, molded coil design.• Coil waterproofing standard.• Screw-in manual override option.


A & B CRange Range

300 ± 70 360 ± 70150 ± 35 180 ± 35



A & B CRange Range

1500 ± 200 1400 ± 200750 ± 100 700 ± 100


another approximately 5 turns to full shift.To Disengage: Turn counterclockwise approximately 6 turns until positive stop

is found.Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1

37.9/10

FLO

W lp

m/g

pm

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

CURRENT amp.1 .2 .3 .4 .5 .6 .7 .8 .9 1.0

Flow vs. Current (207 bar/3000 psi Load)PV70-33C with EC10-3011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -

100 Hz Dither

Attention Manifold Designers:To obtain these high flow capabilitiesusing proportional flow controls andcompensators, optimized cavity drillingsare required. Please consult factory.


Cartridge: Steel with hardened worksurfaces. Zinc-plated exposedsurfaces. Buna N O-rings andback-ups standard.

Standard Ported Body: Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi). Ductileiron and steel bodies available;dimensions may differ; consultfactory

Coil: Unitized thermoplastic encapsu-lated, Class H high temperaturemagnetwire; See page 3.200.1.

Package Weight: 2.27 kg. (5 lbs.).

Seal Kit: SK10-3x-MM (PV);SK10-3x-TB (EC)

DIMENSIONS

MATERIALS TO ORDER

PFR70-33x-E

2.401.2

Override Option(Blank) None

M Screw Type

Voltage0 Less Coil

12 12 VDC24 24 VDC

*Compensator Spring5.52 bar (80 psi) 80

11.03 bar (160 psi) 160

PFR70-33__ - E__ - 8T - __ - __ __ __ __

NOTE: The N.O.PV70-35 may notbe substituted inthis manifold dueto port logicfactors.

*Select Orifice Range and CompensatorSpring by referring to the PerformanceCurves on the preceding page.

*PV Orifice RangeOrifice Range AOrifice Range BOrifice Range C

2-Port, Pressure Compensated

HYDRAFORCE®


DL/W Leadsw/Weatherpak

ConnectorsDR Deutsch

DT04-2P



2.402.1

USASI/ISO:

SYMBOLS

PFR70-33x-F Proportional Priority Flow Regulator, N.C.,

37.9/10

CURRENT amp

FLO

W lp

m/g

pm

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

Flow vs. Current (207 bar/3000 psi Load)PV70-33B with EC10-4011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -2.8 bar/40 psi spring • • • • •


FLO

W lp

m/g

pm

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

CURRENT amp.1 .2 .3 .4 .5 .6 .7 .8 .9 1.0

Flow vs. Current (207 bar/3000 psi Load)PV70-33C with EC10-4011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -2.8 bar/40 psi spring • • • • •


CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (207 bar/3000 psi Load)PV70-33A with EC10-4011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -2.8 bar/40 psi spring • • • • •

100 Hz Dither

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

Priority Port Flow Delivered Out Port ➁:

PERFORMANCE CURVES24 Volt coil used; 130 Hz dither; PWM controller

DESCRIPTIONA pressure-compensated electrically-variable three-port flow regulator that is a priority(bypass) type control. This combination valve uses a PV70-33x proportional cartridgeand an EC10-40 compensator.

OPERATIONThe PFR70-33x-F series will bypass all flow out port ➂ when de-energized at thepressure compensator spring value. When energized, this proportional valve/compensator package will increase and regulate flow out of port ➁, regardless ofsystem working pressure, with an increasing current applied to the solenoid.



RATINGSOperating Pressure: 207 bar (3000 psi)Pressure Rise: Pressure at ➀ begins to rise higher than the compensating pressure

differential when bypass flow exceeds 26.5 lpm (7 gpm).Internal Leakage: 410 cc/min. (25 cu. in./min.) fully closed at 207 bar (3000 psi) out




A & B CRange Range

300 ± 70 360 ± 70150 ± 35 180 ± 35



A & B CRange Range

1500 ± 200 1400 ± 200750 ± 100 700 ± 100





For 12 volt coils, double the current (amp) values shown.

37.9/10

41.4600

LOAD bar/psi

FLO

W lp

m/g

pm

Priority Port Flow Rate Loss Under LoadPV70-33B with EC10-40 Typical11 bar/160 psi compensator —5.5 bar/80 psi compensator - - -2.8 bar/40 psi compensator • • •

82.81200

124.11800

165.52400

206.93000

34.1/930.2/8

22.7/6

15.1/4

7.5/2

26.5/7

18.9/5

11.4/3

3.8/1




Standard Ported Body: Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi). Ductileiron and steel bodies available;dimensions may differ; consultfactory.



Seal Kit: SK10-3X-MM (PV);SK10-4X-TMB (EC)

DIMENSIONS

MATERIALS TO ORDER

PFR70-33x-F

2.402.2


M Screw Type

Voltage0 Less Coil

12 12 VDC24 24 VDC

*Compensator Spring2.76 bar (40 psi) 405.52 bar (80 psi) 80

11.03 bar (160 psi) 160


PFR70-33__ - F__ - 8T - __ - __ __ __ __




HYDRAFORCE®





DT04-2P



OPERATIONThe PFR70-33x-J series will bypass all flow when de-energized at the pressurecompensator spring value. When energized, this proportional valve/compensatorpackage will regulate flow out of port ➁, regardless of system working pressure, withan increasing current applied to the solenoid.






2.403.1

USASI/ISO:

SYMBOLS


37.9/10

41.4600

LOAD bar/psi

FLO

W lp

m/g

pm

Priority Port Flow Rate Loss Under LoadPV70-33A with EC12-40 Typical11 bar/160 psi compensator —

6.9 bar/100 psi compensator - - -

82.81200

124.11800

165.52400

206.93000

34.1/930.2/8

22.7/6

15.1/4

7.5/2

26.5/7

18.9/5

11.4/3

3.8/1

PFR70-33x-J Proportional Priority Flow Regulator, N.C.,

37.9/10

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (207 bar/3000 psi Load)PV70-33B with EC12-40

11 bar/160 psi spring ——6.9 bar/100 psi spring - - - -

100 Hz Dither

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

37.9/10

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (207 bar/3000 psi Load)PV70-33C with EC12-40


100 Hz Dither

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

Priority Port Flow Delivered Out Port ➁:

37.9/10

CURRENT amp

FLO

W lp

m/g

pm


100 Hz Dither

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0



A & B CRange Range

300 ± 70 360 ± 70150 ± 35 180 ± 35



A & B CRange Range

1500 ± 200 1400 ± 200750 ± 100 700 ± 100





For 12 volt coils, double the current (amp) values shown.




Standard Ported Body: Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi). Steeland ductile iron bodies available;dimensions may differ; consultfactory.



Seal Kit: SK10-3x-MM (PV)SK12-4x-TMB (EC)

DIMENSIONS

MATERIALS TO ORDER

PFR70-33x-J

2.403.2

PFR70-33__ - J__ - 10/12T - __ - __ __ __ __


M Screw Type


Voltage0 Less Coil

12 12 VDC24 24 VDC



†


11.03 bar (160 psi) 160


† Ports 1 & 3: SAE 12Port 2: SAE 10

HYDRAFORCE®






DT04-2P


USASI/ISO:

SYMBOLS

2.406.1

PERFORMANCE

15.14

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➁ Coil EnergizedThrough Cartridge & Ported Body


30.28

45.412

60.616

75.720

13.8/200

10.3/150

6.9/100

3.4/50

AB

90.824

12

3

1

2

3

DESCRIPTIONA linear solenoid-driven, two-way normally closed, screw-in cartridge valve designedfor use with a pressure compensator to function as an electrically stroked variableflow regulator.

OPERATIONWith increasing electric current, the PV72-33 changes from full closed to full openwith flow from port ➂ to port ➁. Port ➀ is used only to pressure balance the spool andshould be plugged. The proportional valve is intended to function in tandem withstandard HydraForce pressure compensators at pressure differentials of 12 bar(175 psid) or less, or alone in variable volume pressure-compensated circuits withload sense capability.
















PWM — 4000144 4000133 4000140






DIMENSIONS

MATERIALS TO ORDER

PV72-33

2.406.2

Normally Closed

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87 1.8622.1 47.2

MILLIMETREINCH

1.2531.8ACROSSFLATS

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.62Plugged

0.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1



2

1

3

44.11.74

2.7068.6

.6717.0

3.3785.6

max.

1.5840.1

1.8647.2

MANUALOVERRIDE

OPTION"G"


HYDRAFORCE®

Porting0 Cartridge

Only10T SAE 1012T SAE 1216T SAE 164B 1/2 in. BSP*6B 3/4 in. BSP*


PV72-33__ __ - __ __ __ - __ - __ __ __ __

Flow RangeAB

Voltage0 Less Coil

12 12 VDC24 24 VDC





ManualOverride M

ManualOverride

with Guard G



Connectors


(IP69K Rated)


OPERATIONThe PFR72-33x-J series will bypass all flow when de-energized at the pressurecompensator spring value. When energized, this proportional valve/compensatorpackage will regulate flow out of port ➁, regardless of system working pressure, withan increasing current applied to the solenoid.






2.407.1

USASI/ISO:

SYMBOLS


75.7/20

41.4600

∆P LOAD bar/psi

FLO

W lp

m/g

pm

Priority Port Flow Rate Loss Under LoadPV72-33A with EC12-40 Typical11 bar/160 psi compensator —

6.9 bar/100 psi compensator - - -

82.81200

124.11800

165.52400

206.93000

68.1/1860.6/16

45.4/12

30.2/8

15.1/4

53.0/14

37.9/10

22.7/6

7.5/2

PFR72-33x-J Proportional Priority Flow Regulator, N.C.,


ThresholdCurrent

300 ± 70 mA150 ± 35 mA

Max. ControlCurrent

1500 ± 200 mA750 ± 100 mA






Priority Port Flow Delivered Out Port ➁:For 12 volt coils, double the current (amp) values shown.

75.8/20

CURRENT amp

FLO

W lp

m/g

pm


100 Hz Dither

.1

68.1/18

45.4/12

37.9/10

22.7/6

7.5/2

15.1/4

30.2/8

53.0/14

60.6/16

.2 .3 .4 .5 .6 .7 .8 .9 1.0

75.8/20

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (207 bar/3000 psi Load)PV72-33B with EC12-4011 bar/160 psi spring ——6.9 bar/100 psi spring - - - -

100 Hz Dither

.1

68.1/18

45.4/12

37.9/10

22.7/6

7.5/2

15.1/4

30.2/8

53.0/14

60.6/16

.2 .3 .4 .5 .6 .7 .8 .9 1.0




Standard Ported Body: Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi). Steeland ductile iron bodies available;consult factory.


Package Weight: 2.95 kg. (6.5 lbs.).

Seal Kit: SK12-3x-MM (PV)SK12-4x-TMB (EC)

DIMENSIONS

MATERIALS TO ORDER

PFR72-33x-J

2.407.2

PFR72-33__ - J__ - 12T - __ - __ __ __ __


M Screw Type

*PV Orifice RangeOrifice Range AOrifice Range B

Voltage0 Less Coil

12 12 VDC24 24 VDC

*Compensator Spring4.14 bar (100 psi) 605.17 bar (100 psi) 756.89 bar (100 psi) 100

11.03 bar (160 psi) 160




HYDRAFORCE®





DT04-2P

Coils with internaldiode are available.Consult factory.

DESCRIPTIONA pressure-compensated electrically-variable two-port flow regulator that is normallyclosed when de-energized. This combination valve uses a PV72-33x proportionalcartridge and an EC12-30 compensator.

OPERATIONThis proportional valve/compensator package will regulate flow out of port ➁regardless of system working pressure. With an increasing current applied to thesolenoid, the PFR72-33x-L will increase output flow.



RATINGSOperating Pressure: 207 bar (3000 psi)Internal Leakage: 492 cc/min. (30 cu. in./min.) fully closed at 207 bar (3000 psi) out


2.408.1

USASI:

SYMBOLS

ISO:

PFR72-33x-L Proportional Flow Regulator, N.C.,

ThresholdCurrent (mA)300 ± 200 mA150 ± 35 mA


1500 ± 100 mA750 ± 100 mA







75.8/20

CURRENT amp

FLO

W lp

m/g

pm


100 Hz Dither

.1

68.1/18

45.4/12

37.9/10

22.7/6

7.5/2

15.1/4

30.2/8

53.0/14

60.6/16

.2 .3 .4 .5 .6 .7 .8 .9 1.0

75.8/20

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (207 bar/3000 psi Load)PV72-33B with EC12-30


100 Hz Dither

.1

68.1/18

45.4/12

37.9/10

22.7/6

7.5/2

15.1/4

30.2/8

53.0/14

60.6/16

.2 .3 .4 .5 .6 .7 .8 .9 1.0





Standard Ported Body: Anodizedhigh-strength 6061 T6 aluminumalloy, rated to 240 bar (3500 psi).Steel and ductile iron bodiesavailable; dimensions may differ;consult factory.




DIMENSIONS

MATERIALS TO ORDER

PFR72-33x-L

2.408.2


M Screw Type


Voltage0 Less Coil

12 12 VDC24 24 VDC


11.03 bar (160 psi) 160

PFR72-33__ - L__ - 12T - __ - __ __ __ __




HYDRAFORCE®





DT04-2P



1

2

3

DESCRIPTIONA solenoid operated, electrically-variable, two-way, pressure-compensated, spool-type, normally closed when de-energized, proportional flow control valve with reversefree flow check. It is a restrictive-type 2-way, pressure-compensated flow regulator;port ➁ is blocked and not used.

OPERATIONWhen energized the PV70-34 will regulate flow from port ➀ to port ➂ regardless ofsystem working pressure. With an increasing current applied to the solenoid, thePV70-34 will increase output flow. When the pressure at port ➂ exceeds the pressureat port ➀, the valve will free reverse flow from port ➂ to port ➀.Operation of Manual Override:




RATINGSOperating Pressure: Inlet: 240 bar (3500 psi)Regulated Flow Rate: 0 to 30 lpm (0 to 8 gpm)Reverse Free Flow Cracking Pressure: 1 to 1.4 bar (15 to 20 psi)Internal Leakage: 0.38 lpm (0.10 gpm) at zero currentElectrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC10-3 (Port ➁ does not need to be drilled); See page 9.110.1Cavity Tool: CT10-3X-XX; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1

USASI/ISO:

SYMBOLS

2.412.1

20


FLO

W lp

m/g

pm

Flow vs. Current➀ to ➂ Energized

240 bar/3500 psi; 12V Coil; 110 Hz PWM32 cSt/150 ssu oil at 40°C

40 60 80 100

37.9/10

30.3/8

22.7/6

15.1/4

7.6/2

PERFORMANCE




691000


FLO

W lp

m/g

pm

Regulated Flow vs. Pressure Drop➀ to ➂



1382000

2073000

2764000

37.9/10

30.3/8

22.7/6

15.1/4

7.6/2

1.5 AMP

1.2 AMP

0.8 AMP

0.4 AMP

Pressure Drop vs. Regulated Flow➂ to ➀ De-energized


PR

ES

SU

RE

DR

OP

bar

/psi 13.8/200

10.3/150

6.9/100

3.4/50

7.52

15.14

22.76

37.910

FLOW lpm/gpm

30.28



DIMENSIONS

MATERIALS TO ORDER

2.412.2

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.70

1.81

68.6

46.0

0.87 1.8622.1 47.2

MILLIMETREINCH

1.1328.6 ACROSS

18.8

53.8

66.5

34.5

7.150.86.4

63.5

31.8

31.8

1.36

2.00

Plugged

0.25

2.62

2.12

0.74

2.50

1.25

1.25

0.28

2

3

1



1

2

44.11.74

3

.6717.0

3.3785.6

max.

FLATS

1.7143.4

2.0953.1

MANUALOVERRIDE

OPTION"G"


HYDRAFORCE®







PWM — 4000144 4000133 4000140


PV70-34 __ - __ __ __ - __ - __ __ __ __

Voltage0 Less Coil

12 12 VDC24 24 VDC

Porting0 Cartridge










Connectors


(IP69K Rated)


1

2

3

DESCRIPTIONA solenoid operated, electrically-variable, two-way, pressure-compensated, spool-type, normally closed when de-energized, proportional flow control valve with reversefree flow check. It is a restrictive-type 2-way, pressure-compensated flow regulator;port ➁ is blocked and not used.

OPERATIONWhen energized the PV72-34 will regulate flow from port ➀ to port ➂ regardless ofsystem working pressure. With an increasing current applied to the solenoid, thePV72-34 will increase output flow. When the pressure at port ➂ exceeds the pressureat port ➀, the valve will free reverse flow from port ➂ to port ➀.Operation of Manual Override:




RATINGSOperating Pressure: Inlet: 240 bar (3500 psi)Regulated Flow Rate: 0 to 57 lpm (0 to 15 gpm)Reverse Free Flow Cracking Pressure: 0.7 to 1.0 bar (10 to 15 psi)Internal Leakage: 0.38 lpm (0.10 gpm) at zero currentElectrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC12-3 (Port ➁ does not need to be drilled); See page 9.112.1Cavity Tool: CT12-3X-XX; See page 8.600.1Seal Kit: SK12-3X-MM; See page 8.650.1

USASI/ISO:

SYMBOLS

2.414.1

20


FLO

W lp

m/g

pm

Flow vs. Current➀ to ➂ Energized

240 bar/3500 psi; 12V Coil; 110 Hz PWM32 cSt/150 ssu oil at 40°C

40 60 80 100

75.8/20

56.8/15

37.9/10

18.9/5

PERFORMANCE




750 ± 50 mA

691000


FLO

W lp

m/g

pm

Regulated Flow vs. Pressure Drop➀ to ➂



1382000

2073000

2764000

1.5 AMP

1.2 AMP

0.8 AMP

0.4 AMP

75.8/20

56.8/15

37.9/10

18.9/5

Pressure Drop vs. Regulated Flow➂ to ➀ De-energized


PR

ES

SU

RE

DR

OP

bar

/psi 13.8/200

10.3/150

6.9/100

3.4/50

18.95

37.910

56.815

FLOW lpm/gpm

75.820



DIMENSIONS

MATERIALS TO ORDER

2.414.2

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87 1.8622.1 47.2

MILLIMETREINCH

1.2531.8ACROSSFLATS

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

Plugged

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1



2

1

3

44.11.74

2.7068.6

.6717.0

3.3785.6

max.

1.5840.1

1.8647.2

MANUALOVERRIDE

OPTION"G"


HYDRAFORCE®




Port Plug: For SAE 10 Port: 6103010For SAE 12 Port: 6103012;For SAE 16 Port: 6103016;See page 8.500.1.



PWM — 4000144 4000133 4000140


Porting0 Cartridge



PV72-34 __ - __ __ __ - __ - __ __ __ __

Voltage0 Less Coil

12 12 VDC24 24 VDC








Connectors


(IP69K Rated)


USASI/ISO:

SYMBOLS

2.432.1

PERFORMANCE

20.7/300

7.52

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➁ Coil De-energizedThrough Cartridge & Ported Body


15.14

22.76

30.28

37.910

45.412

53.014

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

ABC

12

3

1

2

3

DESCRIPTIONA linear solenoid-driven, two-way normally open, screw-in cartridge valve designedfor use with a pressure compensator to function as an electrically stroked variableflow regulator.

OPERATIONWith increasing electric current, the PV70-35 changes from full open to full closedwith flow from port ➁ to port ➂. Port ➀ is used only to pressure balance the spool andshould be plugged. The proportional valve is intended to function in tandem withstandard HydraForce pressure compensators at pressure differentials of 21 bar(300 psid) or less, or alone in variable volume pressure-compensated circuits withload sense capability.

The valve is designed to work with industry-common controllers which typicallyfeature current capability to 2 amps @ 12 VDC, PWM, and start/stop trim adjustments(I min./I max.). Consult factory for details and potential sourcing.















PWM — 4000144 4000133 4000140


DIMENSIONS

MATERIALS TO ORDER

PV70-35

2.432.2

Normally Open

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.70

1.81

68.6

46.0

0.87 1.8622.1 47.2

MILLIMETREINCH


18.8

53.8

66.5

34.5

7.1

50.86.4

63.5

31.8

31.8

1.36

2.00Plugged

0.25

2.62

2.12

0.74

2.50

1.25

1.25

0.28

2

3

1



1

2

44.11.74

3

.6717.0

3.3785.6

1.7143.4

2.0953.1

MANUALOVERRIDE

OPTION"G"


HYDRAFORCE®


Standard Ported Body: Weight:0.36 kg. (0.80 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.010.1. Steel and Ductile Ironbodies available; dimensions maaydiffer; consult factory.



PV70-35 __ __ - __ __ __ - __ - __ __ __ __

Voltage0 Less Coil

12 12 VDC24 24 VDC

Porting0 Cartridge






ManualOverride M

ManualOverride

with Guard G



Connectors


(IP69K Rated)

Flow RangeABC


2.433.1

USASI:

SYMBOLS

ISO:


PFR70-35x-E Proportional Flow Regulator, N.O.,

37.9/10

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (No Load)PV70-35A with EC10-3011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -

100 Hz Dither

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

37.9/10

CURRENT amp

FLO

W lp

m/g

pm

.1

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

.2 .3 .4 .5 .6 .7 .8 .9 1.0

Flow vs. Current (No Load)PV70-35B with EC10-3011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -


FLO

W lp

m/g

pm

34.1/9

22.7/6

18.9/5

11.4/3

3.8/1

7.5/2

15.1/4

26.5/7

30.2/8

CURRENT amp.1 .2 .3 .4 .5 .6 .7 .8 .9 1.0

Flow vs. Current (No Load)PV70-35C with EC10-3011 bar/160 psi spring ——5.5 bar/80 psi spring - - - -

100 Hz Dither

DESCRIPTIONA pressure-compensated electrically-variable two-port flow regulator that is normallyopen when de-energized. This combination valve uses a PV70-35x proportionalcartridge and an EC10-30 compensator.

OPERATIONThis proportional valve/compensator package will regulate flow out of port ➁regardless of system working pressure. With an increasing current applied to thesolenoid, the PFR70-35x-E will decrease output flow.



RATINGSOperating Pressure: 207 bar (3000 psi)Leakage: 0.75 lpm (0.2 gpm) max. at 100% current appliedElectrical: 2 standard voltage ratings





ThresholdCurrent

300 ± 200 mA150 ± 100 mA

Max. ControlCurrent

1500 ± 100 mA750 ± 50 mA










DIMENSIONS

MATERIALS TO ORDER

PFR70-35x-E

2.433.2


M Screw Type


Voltage0 Less Coil

12 12 VDC24 24 VDC


11.03 bar (160 psi) 160

PFR70-35__ - E__ - 8T - __ - __ __ __ __




HYDRAFORCE®





DT04-2P



USASI/ISO:

SYMBOLS

2.434.1

PERFORMANCE

12

3

20.7/300

18.95

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➂ Coil De-energizedThrough Cartridge & Ported Body


37.810

56.715

75.720

94.225

113.430

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

AB

1

2

3

DESCRIPTIONA linear solenoid-driven, two-way normally open, screw-in cartridge valve designedfor use with a pressure compensator to function as an electrically stroked variableflow regulator.

OPERATIONWith increasing electric current, the PV72-35 changes from full open to full closedwith flow from port ➁ to port ➂. Port ➀ is used only to pressure balance the spool andshould be plugged. The proportional valve is intended to function in tandem withstandard HydraForce pressure compensators at pressure differentials of 21 bar(300 psid) or less, or alone in variable volume pressure-compensated circuits withload sense capability.















0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140






DIMENSIONS

MATERIALS TO ORDER

PV72-35

2.434.2

Normally Open

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87 1.8622.1 47.2

MILLIMETREINCH

1.2531.8ACROSSFLATS

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.62Plugged

0.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1



2

1

3

44.11.74

2.7068.6

.6717.0

3.3785.6

max.

1.5840.1

1.8647.2

MANUALOVERRIDE

OPTION"G"


HYDRAFORCE®

Porting0 Cartridge



PV72-35__ __ - __ __ __ - __ - __ __ __ __

Flow RangeAB

Voltage0 Less Coil

12 12 VDC24 24 VDC









Connectors


(IP69K Rated)

DESCRIPTIONA pressure-compensated electrically-variable two-port flow regulator that is normallyopen when de-energized. This combination valve uses a PV72-35x proportionalcartridge and an EC12-30 compensator.

OPERATIONThis proportional valve/compensator package will regulate flow out of port ➁regardless of system working pressure. With an increasing current applied to thesolenoid, the PFR72-35x-L will decrease output flow.



RATINGSOperating Pressure: 207 bar (3000 psi)Leakage: 0.75 lpm (0.2 gpm) max. at 100% current appliedElectrical: 2 standard voltage ratings





2.435.1

USASI:

SYMBOLS

ISO:

PFR72-35x-L Proportional Flow Regulator, N.O.,

ThresholdCurrent

300 ± 200 mA150 ± 100 mA

Max. ControlCurrent

1500 ± 100 mA750 ± 50 mA



75.8/20

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (No Load)PV72-35A with EC12-3011 bar/160 psi spring ——6.9 bar/100 psi spring - - - -

100 Hz Dither

.1

68.1/18

45.4/12

37.9/10

22.7/6

7.5/2

15.1/4

30.2/8

53.0/14

60.6/16

.2 .3 .4 .5 .6 .7 .8 .9 1.0

75.8/20

CURRENT amp

FLO

W lp

m/g

pm

Flow vs. Current (No Load)PV72-35B with EC12-3011 bar/160 psi spring ——6.9 bar/100 psi spring - - - -

100 Hz Dither

.1

68.1/18

45.4/12

37.9/10

22.7/6

7.5/2

15.1/4

30.2/8

53.0/14

60.6/16

.2 .3 .4 .5 .6 .7 .8 .9 1.0









DIMENSIONS

MATERIALS TO ORDER

PFR72-35x-L

2.435.2


M Screw Type


Voltage0 Less Coil

12 12 VDC24 24 VDC


11.03 bar (160 psi) 160

PFR72-35__ - L__ - 12T - __ - __ __ __ __




HYDRAFORCE®





DT04-2P


ZL70-30 Proportional, Bi-Directional Flow Control,

SYMBOLS

2.602.1

DESCRIPTIONA solenoid-operated, electrically-variable, pressure-compensated, spool-type,normally closed when de-energized, proportional, bi-directional, flow control valve.An internal compensator spool provides compensated flow across theproportional orifice regardless of flow direction.

OPERATIONThe ZL70-30 provides regulated flow from port ➁ to port ➂, or regulated flow fromport ➂ to port ➁. Port ➀ should be blocked. Regulated flow is proportional to electriccurrent applied to the solenoid.Operation of Manual Override:



FEATURES• Excellent linearity and hysteresis characteristics.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet armature construction.• Manual Override option.

RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: Range A: 0–20 lpm (0–5.3 gpm); Range B: 0–10 lpm (0–2.6 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) maximum at zero currentElectrical: 2 standard voltage ratings

Temperature: -40 to 120°C with Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of





PERFORMANCE


2

3

1

ELECTRO-PROPORTIONAL VALVES—FLOW CONTROL

ABBREVIATED SYMBOL:

USASI/ISO:

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1

FLOW RANGE “A”Regulated Flow vs. Current

240 bar/3500 psi Inlet207 bar/3000 psi at Regulated Port➁ to ➂ ——— ➂ to ➁ – – – –


FLOW RANGE “A”Regulated Flow vs. Pressure Drop

240 bar/3500 psi Inlet➁ to ➂ ——— ➂ to ➁ – – – –


PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1

1.4 amp

1.0 amp

0.7 amp

0.4 amp


0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140





MATERIALS TO ORDER

ZL70-30

2.602.2

ZL70-30 __ __ - __ __ __ - __ - __ __ __ __


Manual Override MVoltage

0 Less Coil12 12 VDC24 24 VDC


Normally Closed


SAE 6 6TSAE 8 8T

SAE 10 10T

HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,167,906

Range0–20 lpm A

(0–5.3 gpm)0–10 lpm B

(0–2.6 gpm)

18.8

53.8

66.5

34.5

7.1

50.86.4

1.36

2.00Plugged

0.25

2.62

2.12

0.74

0.28

2

3

1

1.1328.6FLATS

ACROSS


1

2

MANUALOVERRIDE

OPTION

3

1.7444.1

1.2531.8

1.2531.8 2.50

63.5

3.4286.8

INCHMILLIMETRE

4.33109.9

3.5890.9

1.8446.7


max.






2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

11.4/3.0

9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

FLOW RANGE “B”Regulated Flow vs. Current



FLOW RANGE “B”Regulated Flow vs. Pressure Drop



PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

11.4/3.0

9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

1.4 amp

1.0 amp

0.7 amp

0.4 amp


SYMBOLS

2.604.1

PERFORMANCE

2

3

1

20


FLO

W lp

m/g

pm

Regulated Flow vs. Current240 bar/3500 psi; 12V Coil; 110 Hz PWM


40 60 80 100

75.6/20

60/16

45/12

30/8

15/4

7 bar/100 psi at Regulated Port

— ➁ to ➂

- - ➂ to ➁

691000


FLO

W lp

m/g

pm

Regulated Flow vs. Pressure Drop240 bar/3500 psi; 12V Coil; 110 Hz PWM


1382000

2073000

75.6/20

60/16

45/12

30/8

15/4

— ➁ to ➂- - ➂ to ➁

1.5 AMP1.2 AMP

0.8 AMP

0.4 AMP


ABBREVIATED SYMBOL:

DESCRIPTIONA solenoid-operated, electrically-variable, pressure-compensated, spool-type,normally closed when de-energized, proportional, bi-directional flow control valve. Aninternal compensator spool provides compensated flow across the proportional orificeregardless of flow direction.

OPERATIONThe ZL72-30 provides regulated flow in both directions: from port ➁ to port ➂, or fromport ➂ to port ➁. Port ➀ should be blocked. Regulated flow is proportional to electriccurrent applied to the solenoid.Operation of Manual Override:





RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: 0-50 lpm (0-13 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) maximum at 0 currentElectrical: 2 standard voltage ratings










PWM — 4000144 4000133 4000140





MATERIALS TO ORDER

ZL72-30

2.604.2

ZL72-30 __ - __ __ __ - __ - __ __ __ __


Manual Override M

Voltage0 Less Coil

12 12 VDC24 24 VDC


Normally Closed

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87

1.86

22.1

47.2

MILLIMETREINCH

1.2531.8ACROSS FLATS 53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1

TORQUE:10–12 ft-lbs max. (14–16 Nm)


2

3

44.11.74

MANUALOVERRIDEOPTION

2.7068.6

.6717.0

3.3785.6


SAE 6 6TSAE 8 8T

SAE 10 10T

HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,167,906






SYMBOLS

2.622.1

DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally open when de-energized, proportional, bi-directional, flow controlvalve. An internal compensator spool provides compensated flow across theproportional orifice regardless of flow direction.

OPERATIONThe ZL70-31 provides regulated flow from port ➁ to port ➂, or regulated flow fromport ➂ to port ➁. Port ➀ should be blocked. Regulated flow is inversely proportionalto electric current applied to the solenoid.Operation of Manual Override:



FEATURES• Excellent linearity and hysteresis characteristics.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet armature construction.• Manual Override option.

RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: Range A: 0–19 lpm (0–5.0 gpm); Range B: 0–9.5 lpm (0–2.5 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) maximum at zero currentElectrical: 2 standard voltage ratings






650 ± 50 mA

PERFORMANCE


2

3

1


ABBREVIATED SYMBOL:

USASI/ISO:

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1




FLOW RANGE “A”Regulated Flow vs. Pressure Drop



PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1

0 amp

0.6 amp

0.9 amp

1.1 amp


0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140





MATERIALS TO ORDER

ZL70-31

2.622.2

ZL70-31 __ __ - __ __ __ - __ - __ __ __ __


Manual Override M Voltage0 Less Coil

12 12 VDC24 24 VDC


Normally Open


SAE 6 6TSAE 8 8T

SAE 10 10T

HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,167,906

(continued)

Range0–19 lpm A

(0–5.0 gpm)0–9.5 lpm B

(0–2.5 gpm)

18.8

53.8

66.5

34.5

7.150.86.4

1.36

2.000.25

2.62

2.12

0.74

0.28

2

3

1

1.1328.6FLATS

ACROSS


1

2

MANUALOVERRIDE

OPTION

3

1.7444.1

1.2531.8

1.2531.8 2.50

63.5

3.4286.8

INCHMILLIMETRE

4.33109.9

3.5890.9

1.8446.7


max.





PERFORMANCE

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

11.4/3.0

13.2/3.5

9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

FLOW RANGE “B”Regulated Flow vs. Current



FLOW RANGE “B”Regulated Flow vs. Pressure Drop



PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

11.4/3.0

9.5/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

0 amp

0.6 amp

0.9 amp

1.1 amp


SYMBOLS

2.624.1

PERFORMANCE

2

3

1

20


FLO

W lp

m/g

pm



40 60 80 100

75.6/20

60/16

45/12

30/8

15/4

7 bar/100 psi at Regulated Port

— ➁ to ➂

- - ➂ to ➁

691000


FLO

W lp

m/g

pm



1382000

2073000

75.6/20

60/16

45/12

30/8

15/4

— ➁ to ➂- - ➂ to ➁

0 AMP

0.3 AMP

0.9 AMP

0.6 AMP

1.1 AMP

ABBREVIATED SYMBOL:

DESCRIPTIONA solenoid-operated, electrically-variable, pressure-compensated, spool-type,normally open when de-energized, proportional, bi-directional flow control valve. Aninternal compensator spool provides compensated flow across the proportional orificeregardless of flow direction.

OPERATIONThe ZL72-31 provides regulated flow in both directions: from port ➁ to port ➂, or fromport ➂ to port ➁. Port ➀ should be blocked. Regulated flow is inversely proportionalto electric current applied to the solenoid.Operation of Manual Override:





RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: 0-50 lpm (0-13 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) maximum at 1.5 ampElectrical: 2 standard voltage ratings







625 ± 50 mA




0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140





DIMENSIONS

MATERIALS TO ORDER

ZL72-31

2.624.2

ZL72-31 __ - __ __ __ - __ - __ __ __ __


Manual Override M



Normally Open

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87

1.86

22.1

47.2

MILLIMETREINCH


82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1



2

3

44.11.74


2.7068.6

.6717.0

3.3785.6


SAE 6 6TSAE 8 8T

SAE 10 10T

HYDRAFORCE®

U.S. Patent 6,167,906






SYMBOLS

2.632.1

DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally closed when de-energized, proportional, bi-directional, priority-typeflow control valve. An internal compensator spool provides compensated flow acrossthe proportional orifice regardless of flow direction.

OPERATIONThe ZL70-33 provides regulated flow from port ➀ to port ➂ with bypass at port ➁;or regulated flow from port ➂ to port ➁ with port ➀ blocked externally, typically with acheck valve (see symbol drawing). Regulated flow is proportional to electric currentapplied to the solenoid.Application Notes: The ZL70-33 may be used for single-acting cylinder applicationswhere lowering is provided by gravity force. A minimum load (defined on performancecurve as minimum pressure at port ➂) is required for uninterrupted lowering.The hydraulic circuit must include a check valve and a poppet-type solenoid valve(SV08-20 type) connected as shown on the circuit symbol and placed close to theZL70-33 valve, if possible in the same manifold. See Application Guide.Operation of Manual Override: To Engage: Turn clockwise approximately 1 turn toreach start point. Continue another approximately 5 turns to full shift. To Disengage:Turn counterclockwise approximately 6 turns until positive stop is found.

FEATURES• Excellent linearity and hysteresis. • Efficient wet armature construction.• Hardened spool and cage for long life. • Manual Override option.• Optional coil voltages and terminations.

RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: Range A: 0–19 lpm (0–5.0 gpm); Range B: 0–9.5 lpm (0–2.5 gpm)Input Flow: Range A: 0–25.5 lpm (0–6.5 gpm); Range B: 0–15 lpm (0–4.0 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) maximum at zero currentElectrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC10-L3; See page 9.110.1; Cavity Tool: CT10-3X-XX; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1




PERFORMANCE


2

3

1

CHECK VALVE(TYPICAL)


USASI/ISO:

ABBREVIATED SYMBOL:

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1


Input Flow 24.6 lpm/6.5 gpm; Port ➁ to Tank➀ to ➂ 207 bar/3000 psi at Port 3 ———➂ to ➁ 240 bar/3500 psi at Port 3 – – – –

12V Coil; 110 Hz PWM; 32 cSt/150 sus oil at 40°C

FLOW RANGE “A”Regulated Flow vs. Pressure

Inlet Flow: 24.5 lpm/6.5 gpm; Port ➁ to Tank➀ to ➂ ——— ➂ to ➁ — — —

➂ to ➁, Min. Operating Pressure at ➂ - - - - -12V Coil; 110 Hz PWM; 32 cSt/150 sus oil at 40°C

PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1

1.4 amp

1.0 amp

0.8 amp

0.5 amp



PWM — 4000144 4000133 4000140





MATERIALS TO ORDER

ZL70-33

2.632.2

ZL70-33 __ __ - __ __ __ - __ - __ __ __ __


Manual Override M Voltage0 Less Coil12 12 VDC24 24 VDC


Normally Closed


SAE 6 6TSAE 8 8T

HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,116,263

(continued)

Range0–19 lpm A

(0–5.0 gpm)0–9.5 lpm B

(0–2.5 gpm)

MILLIMETREINCH


1.1328.6ACROSSFLATSTORQUE: 27 ft-lbs max.(36.7 Nm)


4.30109.3

3.5690.3

2.1354.1

3.3986.2

0.7519.1

2.8472.1

3.2582.6

1.6441.6

0.287.13

2.0050.8

0.256.35

2

3

1

1.7444.1

1.2531.8

1.2531.8 2.50

63.5

3

2

1





PERFORMANCE

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

11.4/3.0

9.4/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

FLOW RANGE “B”Regulated Flow vs. CurrentInput Flow 15 lpm/4.0 gpmPort ➁ connected to Tank

➀ to ➂ 207 bar/3000 psi at Port 3 ———➂ to ➁ 240 bar/3500 psi at Port 3 – – – –


FLOW RANGE “B”Regulated Flow vs. PressureInlet Flow: 15 lpm/4.0 gpmPort ➁ Connected to Tank

➀ to ➂ ——— ➂ to ➁ — — —➂ to ➁, Min. Operating Pressure at ➂ - - - - -


PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

11.4/3.0

9.4/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

1.4 amp

1.0 amp

0.8 amp

0.5 amp


SYMBOLS

2.634.1

2

3

1


20


FLO

W lp

m/g

pm



40 60 80 100

75.6/20

60/16

45/12

30/8

15/4

207 bar/3000 psi at Port ➂

— ➀ to ➂

- - ➂ to ➁

691000


FLO

W lp

m/g

pm



1382000

2073000

75.6/20

60/16

45/12

30/8

15/4

— ➀ to ➂- - ➂ to ➁

1.5 AMP

1.2 AMP

0.9 AMP

0.6 AMP

0.3 AMP

ABBREVIATED SYMBOL:

DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally closed when de-energized, proportional, bi-directional, priority-typeflow control valve. An internal compensator spool provides compensated flow acrossthe proportional orifice regardless of flow direction.

OPERATIONThe ZL72-33 provides regulated flow from port ➀ to port ➂ with bypass at port ➁;or regulated flow from port ➂ to port ➁ with port ➀ blocked externally, typically with acheck valve (see symbol drawing). Regulated flow is proportional to electric currentapplied to the solenoid.Application Notes: The ZL72-33 may be used for single-acting cylinder applicationswhere lowering is provided by gravity force. A minimum load (defined on performancecurve as minimum pressure at port ➂) is required for uninterrupted lowering.The hydraulic circuit must include a check valve and a poppet-type solenoid valveconnected as shown on the circuit symbol and placed close to the ZL72-33 valve, ifpossible in the same manifold. Consult factory.Operation of Manual Override: To Engage: Turn clockwise approximately 1 turn toreach start point. Continue another approximately 5 turns to full shift. To Disengage:Turn counterclockwise approximately 6 turns until positive stop is found.



RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: 0-50 lpm (0-13 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) maximum at 0 currentElectrical: 2 standard voltage ratings







PERFORMANCE



USASI/ISO:


0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140





MATERIALS TO ORDER

ZL72-33

2.634.2

ZL72-33 __ - __ __ __ - __ - __ __ __ __


Manual Override M

Voltage0 Less Coil

12 12 VDC24 24 VDC


Normally Closed

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

0.87

1.86

22.1

47.2

MILLIMETREINCH


82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1



2

3

44.11.74


2.7068.6

.6717.0

3.3785.6



HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,116,263







SYMBOLS

2.662.1

DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally closed when de-energized, proportional, bi-directional, priority-typeflow control valve.

OPERATIONThe ZL70-36 provides priority regulated flow from port ➀ to port ➂ with bypass at port➁; or regulated flow from port ➂ to port ➁ with port ➀ blocked externally, typicallywith a check valve (see symbol drawing). Regulated flow is proportional to electriccurrent applied to the solenoid.

Application Notes: The ZL70-36 may be used for single-acting cylinder applicationswhere lowering is provided by gravity force. The ZL 70-36 has no minimum loadrestrictions provided the load is enough to overcome cylinder friction and otherfrictions in the system. At low loads, the lowering speed can be slower than at heavierload if pressure drop is less than the compensation value of the valve.

The hydraulic circuit must include a check valve and a poppet-type solenoid valve(SV08-20 type) connected as shown on the circuit symbol and placed close to theZL70-36 valve, if possible in the same manifold. See Application Guide.Operation of Manual Override: To Engage: Turn clockwise approximately 1 turn toreach start point. Continue another approximately 5 turns to full shift. To Disengage:Turn counterclockwise approximately 6 turns until positive stop is found.

FEATURES• Excellent linearity and hysteresis. • Efficient wet armature construction.• Hardened spool and cage for long life. • Manual Override option.• Optional coil voltages and terminations.

RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: Range A: 0–19 lpm (0–5.0 gpm); Range B: 0–9.5 lpm (0–2.5 gpm)Input Flow: Range A: 0–25.5 lpm (0–6.5 gpm); Range B: 0–15 lpm (0–4.0 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) maximum at zero currentElectrical: 2 standard voltage ratings


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1.Cavity: VC10-L3; See page 9.110.1; Cavity Tool: CT10-3X-XX; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1




700 ± 50 mA

PERFORMANCE


2

3

1


USASI/ISO:

ABBREVIATED SYMBOL:

2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

22.7/6

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1


Input Flow 24.6 lpm/6.5 gpm; Port ➁ to Tank➀ to ➂ 207 bar/3000 psi at Port 3 ———➂ to ➁ 240 bar/3500 psi at Port 3 – – – –


FLOW RANGE “A”Regulated Flow vs. Pressure

Inlet Flow: 24.5 lpm/6.5 gpm; Port ➁ to Tank➀ to ➂ ——— ➂ to ➁ — — —


PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

26.5/7

22.7/6

18.9/5

15.1/4

11.4/3

7.6/2

3.8/1

1.4amp

1.0amp

0.8amp

0.5amp



PWM — 4000144 4000133 4000140





MATERIALS TO ORDER

ZL70-36

2.662.2

ZL70-36 __ __ - __ __ __ - __ - __ __ __ __


Manual Override M Voltage0 Less Coil

12 12 VDC24 24 VDC


Normally Closed


SAE 6 6TSAE 8 8T

HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,116,263

(continued)

Range0–19 lpm A

(0–5.0 gpm)0–9.5 lpm B

(0–2.5 gpm)

MILLIMETREINCH


1.1328.6ACROSSFLATSTORQUE: 27 ft-lbs max.(36.7 Nm)


4.30109.3

3.5690.3

2.1354.1

3.3986.2

0.7519.1

2.8472.1

3.2582.6

1.6441.6

0.287.13

2.0050.8

0.256.35

2

3

1

1.7444.1

1.2531.8

1.2531.8 2.50

63.5

3

2

1





2010


FLO

W lp

m/g

pm

40 5030 60 70 80 90 100

13.2/3.5

11.4/3.0

9.4/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

FLOW RANGE “B”Regulated Flow vs. CurrentInput Flow 15 lpm/4.0 gpmPort ➁ connected to Tank

➀ to ➂ 207 bar/3000 psi at Port 3 ———➂ to ➁ 240 bar/3500 psi at Port 3 – – – –


FLOW RANGE “B”Regulated Flow vs. PressureInlet Flow: 15 lpm/4.0 gpmPort ➁ Connected to Tank

➀ to ➂ ——— ➂ to ➁ — — —12V Coil; 110 Hz PWM


PRESSURE bar/psi

1031500

1722500

2423500

35500

FLO

W lp

m/g

pm

13.2/3.5

11.4/3.0

9.4/2.5

7.6/2.0

5.7/1.5

3.8/1.0

1.9/0.5

1.0amp

1.4amp

0.8amp

0.5amp

PERFORMANCE


SYMBOLS

2.664.1

2

3

1


20


FLO

W lp

m/g

pm

Regulated Flow vs. CurrentInlet Flow: 57 lpm/15 gpmPort ➁ Connected to Tank

——— ➀ to ➂, 207 bar/3000 psi at ➂– – – – ➂ to ➁, 240 bar/3500 psi at ➂


40 60 80 100

56.8/15

45.4/12

34.1/9

22.7/6

11.4/3

35500

1031500

PRESSURE at ➂ bar/psi

FLO

W lp

m/g

pm

1722500

2413500

56.8/15

45.4/12

34.1/9

22.7/6

11.4/3

Regulated Flow vs. PressureInlet Flow: 57 lpm/15 gpmPort ➁ Connected to Tank

——— ➀ to ➂– – – – ➂ to ➁


1.2 AMP

1.6 AMP

0.8 AMP

0.4 AMP

DESCRIPTIONA solenoid-operated, electrically-variable, three-port, pressure-compensated, spool-type, normally closed when de-energized, proportional, bi-directional, priority-typeflow control valve.

OPERATIONThe ZL72-36 provides priority regulated flow to port ➂ with input at port ➀, andbypass at port ➁; or regulated flow from port ➂ to port ➁ with input at port ➀ blocked.Regulated flow is proportional to electric current applied to the solenoid.

Application Notes: The ZL72-36 may be used for single-acting cylinder applicationswhere lowering is provided by gravity force. There are no minimum load restrictions,provided the load is enough to overcome cylinder friction and other frictions in thesystem. At low load the lowering speed can be slower than at heavier load if pressuredrop is less than the compensation value of the valve.The hydraulic circuit must include a check valve and a poppet-type solenoid valve(SV10-20 type) connected as shown on the circuit symbol and placed close to theZL72-36 valve, if possible in the same manifold. See Application Guide.Operation of Manual Override: To Engage: Turn clockwise approximately 1 turn toreach start point. Continue another approximately 5 turns to full shift. To Disengage:Turn counterclockwise approximately 6 turns until positive stop is found.

FEATURES• Excellent linearity and hysteresis. • Optional coil voltages and terminations.• Hardened spool and cage for long life. • Manual override option.• Efficient wet armature construction.

RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Regulated Flow: 0-45 lpm (0-12 gpm)Internal Leakage: 0.38 lpm (0.10 gpm) at zero currentElectrical: 2 standard voltage ratings






800 ± 50 mA

PERFORMANCE



ABBREVIATED SYMBOL:

USASI/ISO:


0-5 VDC 7114950 4000046 4000049 40001360-10 VDC 4000070 4000141 4000124 40001374-20 mA 4000123 4000143 4000130 4000139

PWM — 4000144 4000133 4000140w/24V Coil

0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140





MATERIALS TO ORDER

ZL72-36

2.664.2

ZL72-36 __ - __ __ __ - __ - __ __ __ __


Manual Override M



Normally Closed

CI

EC

RO

FA

R D Y H

XX

XX

XX

.N


2.7870.6

MILLIMETREINCH

1.2531.8

ACROSS53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1



2

3

44.11.74


3.5790.7

3.4186.5

4.32109.6

FLATS

1.8647.2



HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,116,263

Terminations (VDC)DS Dual SpadesDG DIN 43650DL Leadwires (2)




ELECTRO-PROPORTIONAL VALVES—PRESSURE CONTROLS

TS08-20 Proportional Electric Relief Valve

USASI/ISO:

SYMBOLS

2.812.1

PERFORMANCE

FLOW lpm/gpm

0.750.2

1.510.4

2.270.6

3.020.8

3.791.0

PR

ES

SU

RE

bar

/psi

3.4/50

2.8/40

2.1/30

1.4/20

0.7/10

Pressure Drop vs. Flow CharacteristicFor Flow ➀ to ➁ with Coil De-energized

Body & Line Only

Cartridge A OnlyVert. Mount

Cartridge A OnlyHoriz. Mount

Cartridge B OnlyVert. Mount

Cartridge B OnlyHoriz. Mount

Relief Pressure vs.Current (DC) 260 Hz Dither

Relieving Pressure ➀ to ➁for Various Relief Pressure Ranges

PR

ES

SU

RE

(ps

i)

0

200

100

300

400

500

600

PR

ES

SU

RE

(ba

r)

0

1510

5

20

25

30

35

40

45

% of Maximum Control Current0 2010 30 50 70 9040 60 80 100

BA

Typical Relief Pressure vs. Flow CharacteristicTypical Relieving Pressure ➀ to ➁

at Various %’s of Maximum Control CurrentPressure Range “A” (20.7 bar/300 psi)

Pressure Range “B” (34.5 bar/5000 psi); Cartridge in Body

FLOW (gpm)0 0.5 1.0 1.5 2.0 2.5 3.0

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

FLOW (lpm)0 1 2 3 654 7 8 9 10 11 12

50% Max. Control Current




DESCRIPTIONA screw-in, cartridge-style, direct acting, poppet-type hydraulic relief valve, which canbe infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for useas a pressure limiting device in demanding applications.

OPERATIONThe TS08-20 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to offsetthe electrically induced solenoid force. With no current applied to the solenoid, thevalve will free flow from ➀ to ➁.

Note: Back pressure on port ➁ becomes additive to the pressure setting at a 1:1 ratio.

FEATURES• 12 and 24 volt coils standard.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Waterproofed coils standard.

RATINGSMaximum Inlet Pressure: 34.5 bar (500 psi)Maximum Control Current: 0.65 amps for 12 VDC coil; 0.33 amps for 24 VDC coilControl Signal: DC or PWM (Significant improvements in valve performance occur

with superimposed dither, with either control method.)Dither Frequency: 250 Hz or higherHysteresis with Dither 250 Hz: 3.0% (7% maximum without dither)Operational Relief Pressure Range from Zero to Maximum Control Current:

A: 0–34.5 bar (0–500 psi); B: 0–20.7 bar (0–300 psi)Rated Flow: A: 3.8 lpm/1 gpm @ 1.4 bar/20 psi pressure drop

B: 3.8 lpm/1 gpm @ 0.8 bar/12 psi pressure dropStep Response: TON <27 ms; TOFF <50 msFlow Path: Free Flow: ➀ to ➁ coil de-energized; Relieving: ➀ to ➁ coil energizedTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities


the reservoir oil level. This will maintain oil in the armature preventing trapped airinstability. If this is not feasible, mount the valve horizontally for best results.

Cavity: VC08-2; See page 9.108.1; Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-B; See page 8.650.1Coil Nut: Part No. 7004410;


Input Sig.w/12V or DIN Coil PCB Metal DIN Rail24V Coil Mount Board Box Mount0-5 VDC 4000161 4000194 4000174 4000136

0-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140


TO ORDER

TS08-20

2.812.2

TS08-20__ - __ - __ - __ __ __ __

MaximumRelief Pressure

34.5 bar (500 psi) A20.7 bar (300 psi) B


SAE 6 6TSAE 8 8T



1.4035.6

1.41

TORQUE: 5 ft-lb(6.8 Nm) max.

DIA.35.8

0.75 ACROSS FLATS19.1

2.3359.2

E-CoilView

Standard Coil View

MATERIALS


Standard Ported Body: Weight:0.16 kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); See page8.008.1. Ductile iron and steel bodiesavailable; dimensions may differ;consult factory.

Standard Coil: Weight: 0.11 kg. (0.25lbs.); Unitized, thermoplastic encap-sulated, Class H high temperaturemagnetwire; See page 3.200.1.


HYDRAFORCE®

DIMENSIONS

Voltage0 Less Coil

10 10 VDC (0.80 amps max.)12 12 VDC (0.65 amps max.)20 20 VDC (0.40 amps max.)24 24 VDC (0.33 amps max.)



Termination Std. CoilDS Dual SpadesDG DIN 43650DL Leadwires (2)



Termination E-CoilER Deutsch DT04-2P

(IP69K Rated)EY Metri-Pack® 150

(IP69K Rated)



DESCRIPTIONA screw-in, cartridge-style, direct acting, poppet-type hydraulic relief valve, which canbe infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for use as apressure limiting device in demanding applications.

OPERATIONThe TS38-20 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to offsetthe electrically induced solenoid force. With no current applied to the solenoid, thevalve will free flow from ➀ to ➁.

Note: Back pressure on port ➁ becomes additive to the pressure setting at a 1:1 ratio.

FEATURES• Airbleed standard.• 12 and 24 volt coils standard.• Industry common cavity.

RATINGSMaximum Port Pressure: 241 bar (3500 psi)Maximum Control Current: 1.10 amps for 12 VDC coil; 0.55 amps for 24 VDC coilControl Signal: DC or PWM (Significant improvements in valve performance occur

with superimposed dither, with either control method.)Dither Frequency: 150 Hz or higherHysteresis with Dither 250 Hz: 3.3% (7% maximum without dither)Operational Relief Pressure Range from Zero to Maximum Control Current:

A: 0–207 bar (0–3000 psi); B: 0–138 bar (0–2000 psi); C: 0–69 bar (0–1000 psi)Rated Flow: AS: 11.4 lpm/3 gpm @ 20 bar/290 psi pressure drop

BS: 11.4 lpm/3 gpm @ 10 bar/150 psi pressure dropCS: 11.4 lpm/3 gpm @ 5.5 bar/80 psi pressure drop

Step Response: TON <50 ms; TOFF <7 msFlow Path: Free Flow: ➀ to ➁ coil de-energized; Relieving: ➀ to ➁ coil energizedTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities





USASI/ISO:

SYMBOLS

2.813.1

PERFORMANCE

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)


Vertical Mount - - - - ; Horizontal Mount ——

0 1 2 3

00 0

50

100

150

200

250

300

2468

10121416182022

2 4 6 8 1210

A

B

C

Relief Pressure vs.Current (DC) 250 Hz Dither

Relieving Pressure ➀ to ➁

PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

2500

3000

3500

PR

ES

SU

RE

(ba

r)

0

50

100

150

200

250


A

B

C

Typical Relief Pressure vs. Flow CharacteristicTypical Relieving Pressure ➀ to ➁

at Various %’s of Maximum Control CurrentPressure Range A: (207 bar/3000 psi);

B: (138 bar/2000 psi); C: (69 bar/1000 psi); Cartridge in Body

FLOW (gpm)0 1 2 3

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

FLOW (lpm)0 2 4 6 8 10 12





• Optional waterproof E-Coils rated up to IP69K.• Manual override optional.


0-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140


MATERIALS



Standard Coil: Weight: 0.32 kg.(0.7 lbs.); Unitized, thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fullyencapsulated with rugged externalmetal shell; Rated up to IP69K withintegral connectors; Note: See page3.400.1 for all E-Coil retrofitapplications.

TO ORDER

TS38-20

2.813.2

TS38-20 __ __ - __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T




207 bar (3000 psi) AS138 bar (2000 psi) BS69 bar (1000 psi) CS

OptionNone (Blank)

Manual Override M

1.6241.1

1.84DIA.

46.7

2.9875.7 Std. Coil

View

E-CoilView


TORQUE18 – 20 ft-lbs

(24.5 – 27.1 Nm)max.

HYDRAFORCE®

DIMENSIONS

Voltage0 Less Coil








(IP69K Rated)



DESCRIPTIONA screw-in, cartridge-style, single-stage, poppet-type pressure relieving valve, whichcan be infinitely adjusted across a prescribed range using a variable electric input.Pressure output is inversely proportional to DC current input.

OPERATIONThe TS38-21 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to openthe valve by overcoming the preset spring force. With no current applied, the valvewill relieve at ±50 psi of the spring maximum. Applying current to the coil reduces theinduced spring force thereby reducing the valve setting.

FEATURES• 12 and 24 volt coils standard.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Hardened parts for long life.

RATINGSMaximum Operating Pressure: 240 bar (3500 psi)Maximum Control Current: 1.10 amps for 12 VDC coil; 0.55 amps for 24 VDC coilRelief Pressure Range from Zero to Maximum Control Current:

Minimum Pressure is factory adjustable.(A) 207–6.9 bar (3000–100 psi)(B) 138–6.9 bar (2000–100 psi)(C) 69–6.9 bar (1000–100 psi)

Rated Flow: 1.1 lpm/0.3 gpm; ∆P = 10 bar (150 psi), cartridge only,➀ to ➁ coil energized

Flow Path: Free Flow: ➀ to ➁ coil energized; Relieving: ➀ to ➁ coil de-energizedTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities





USASI/ISO:

SYMBOLS

2.823.1

PERFORMANCE



PRESSURE DROP VS. FLOW CHARACTERISTICFlow from Port ➀ to Port ➁ with Coil Energized

Body and Line Pressure Drop: 0.34 bar/5 psi at 1.90 lpm/0.5 gpm

32

28

24

20

16

12

8

4

0

PR

ES

SU

RE

(BA

R)

PR

ES

SU

RE

(PS

I)

FLOW (GPM)

FLOW (LPM)

0

0

100

200

300

400

500

0.1 0.2 0.3 0.4 0.5

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

Ranges A & B

Range C

TYPICAL RELIEF PRESSURE VS. FLOW CHARACTERISTICTypical Relieving Pressure Port ➀ to Port ➁

No Current Applied; Cartridge in Body

FLOW (LPM)

FLOW (GPM)0

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

0.1 0.2 0.3 0.4 0.5

0

25

50

75

100

125

150

175

200

225

250

275

PR

ES

SU

RE

(B

AR

)

0

500

1000

1500

2000

2500

3000

3500

4000

PR

ES

SU

RE

(P

SI)

Range C

Range B

Range A

DIMENSIONS

MATERIALS


Standard Ported Body: Weight: 0.16kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); See page8.008.1. Ductile iron and steel bodiesavailable; dimensions may differ;consult factory.

Standard Coil: Weight: 0.32 kg. (0.7lbs.); Unitized, thermoplastic encap-sulated, Class H high temperaturemagnetwire; See page 3.200.1.


TO ORDER

TS38-21

2.823.2

TS38-21 __ __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T


*BSP Body; U.K. Mfr. Only Voltage0 Less Coil


1.6241.1

1.84DIA.

46.7

StandardCoil View

E-CoilView

TORQUE7–10 ft-lbs(9.5–13.6 Nm) max.


(24.5 – 27.1 Nm)max.

2.5564.9

HYDRAFORCE®

(continued)

MaximumOperating Pressure

207 bar (3000 psi) A138 bar (2000 psi) B

69 bar (1000 psi) C








(IP69K Rated)

PERFORMANCE

RELIEF PRESSURE VS. CURRENT 200 Hz PWMRelieving Pressure Port ➀ to Port ➁

with Constant Flow of 0.76 lpm/0.2 gpmBody and Line Pressure Drop: 0.34 bar/5 psi at 1.90 lpm/0.5 gpm

500

0

1000

1500

2000

2500

3000

3500

% of MAXIMUM CONTROL CURRENT

PR

ES

SU

RE

(B

AR

)

PR

ES

SU

RE

(P

SI)

0 10 20 30 40 50 60 70 80 90 100 110

0

50

100

150

200

Range C

Range B

Range A

Input Sig.w/12V or DIN Coil PCB Metal DIN Rail24V Coil Mount Board Box Mount0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140


U.S. Patent 6,267,350

TS58-21F Proportional Electric Relief Valve

DESCRIPTIONA screw-in, cartridge-style, single-stage, poppet-type pressure relieving valve, which can be infi nitely adjusted across a prescribed range using a variable electric input. Pressure output is inversely proportional to DC current input.

OPERATIONThe TS58-21F blocks fl ow from ➀ to ➁ until suffi cient pressure is present at ➀ to open the valve by overcoming the preset spring force. With no current applied, the valve will relieve at ±50 psi of the spring maximum. Applying current to the coil reduces the induced spring force thereby reducing the valve setting.

FEATURES• 12 and 24 volt coils standard.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Hardened parts for long life.


344.7–6.9 bar (5000–100 psi)Rated Flow: 1.9 lpm/0.5 gpm; ΔP = 6.9 to 9 bar (100 to 130 psi), cartridge only,

➀ to ➁ coil energizedFlow Path: Free Flow: ➀ to ➁ coil energized; Relieving: ➀ to ➁ coil de-energizedTemperature: -40° to 100°C (-40° to 212° F) with standard Buna N seals

-26° to 204°C (-15° to 400°F) with Fluorocarbon seals;-54° to 104°C (-65° to 225°F) with Polyurethane seals


7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation Recommendation: When possible, the valve should be mounted below

the reservoir oil level. This will maintain oil in the armature preventing trapped air instability. If this is not feasible, mount the valve horizontally for best results.

Cavity: VC08-2; See page 9.108.1; Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-B; See page 8.650.1Coil Nut: Part No. 4540550

USASI/ISO:

SYMBOLS

2.825.1

PERFORMANCE


U.S. Patent 6,267,350

HYDRAFORCE.com®

PRESSURE DROP VS. FLOW CHARACTERISTICFlow from Port 1 to Port 2 with Coil Energized

32

28

24

20

16

12

8

4

0

PR

ES

SU

RE

(B

AR

)

PR

ES

SU

RE

(P

SI)

FLOW (GPM)

FLOW (LPM)

0

0

100

200

300

400

500

0.1 0.2 0.3 0.4 0.5

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

TYPICAL RELIEVING PRESSURE Port 1 to Port 2; No Current Applied; Upper & Lower Limit

FLOW (LPM)

FLOW (GPM)0

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

0.1 0.2 0.3 0.4 0.5

241

276

310

345

379

PR

ES

SU

RE

(B

AR

)

3500

4000

4500

5000

5500

PR

ES

SU

RE

(P

SI)

Performance info. continued on following page.

RP



DIMENSIONS

MATERIALS

Cartridge: Weight: 0.16 kg. (0.35 lbs.) Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-rings and polyester elastomer back-ups standard.

Ported Body: Weight: 0.54 kg. (1.2 lbs.), Ductile iron standard; rated to 345 bar (5000 psi); See page 8.008.1.

Standard Coil: Weight: 0.32 kg. (0.7 lbs.) Unitized, thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1

E-Coil: Weight: 0.41 kg. (0.9 lbs.) Fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors. Note: See page 3.400.1 for all E-Coil retrofit applications.

TO ORDER

TS58-21F

2.825.2

TS58-21F __ __ - __ - __ __ __- __ __ __ __ __

Porting Cartridge Only 0 SAE 6 6TD 3/8 in. BSP* 3BD 1/2 in. BSP* 4BD *BSP Body; U.K. Mfr. Only

Pressure Setting in bar 275.8 to 344.7 bar only Specify, for example: 300 bar M300 Pressure Setting in psi 4000 to 5000 psi only Specify, for example: 4500 bar 45.0

Voltage 0 Less Coil 10 10 VDC (1.30 amps max.) 12 12 VDC (1.10 amps max.) 20 20 VDC (0.65 amps max.) 24 24 VDC (0.55 amps max.)

(continued)

Screen No Screen (blank) 150μ Screen S


Pressure Setting (X 100 psi [6,9 bar]) From 4000 psi [275,8 bar] to 5000 psi [344,7 bar] ONLY

PERFORMANCEU.S. Patent 6,267,350

®HYDRAFORCE

HYDRAFORCE.com®

Recommended Electronic Controllers:Model EFDR2 Multi-Input Fan Drive Controller.For more information go to: http://www.hydraforce.com/Electro/fandrive.htmor Recommended Electronic Controllers catalog page 2.001.1 (Table 2)

RELIEF PRESSURE vs. CURRENT 200 Hz PWMRelieving Pressure Port 1 to Port 2 at 0.38 lpm/0.1 gpm

500

0

1000

1500

2000

2500

3000

3500

4000

4500

5000

5500


PR

ES

SU

RE

(B

AR

)

PR

ES

SU

RE

(P

SI)

0 10 20 30 40 50 60 70 80 90 100 110

0

50

100

150

200

250

300

350

1.6241.1

1.84DIA.

46.7

StandardCoil View

E-CoilView



(24.5 – 27.1 Nm)

2.5564.9



RP


http://www.hydraforce.com/Electro/fandrive.htm



TS10-26 Proportional Electric Relief w/Internally

USASI/ISO:

SYMBOLS

2.852.1

PERFORMANCE

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)


0 5 10 15 20 25

00 0

50

100

150

200

250

2468

101214161820

20 40 60 80 100

Cartridge & Body

Cartridge Only

Body Only

Relief Pressure vs.Current (DC) Characteristic

200 Hz PWMRelieving Pressure ➀ to ➁

PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

2500

3000

3500

PR

ES

SU

RE

(ba

r)

0

50

100

150

200

250


A

B

C

Typical Relief Pressure vs. Flow Characteristic

Typical Relieving Pressure ➀ to ➁ at Various %’s of Maximum Control Current

Pressure Range “A” (207 bar/3000 psi); Cartridge in Body FLOW (gpm)

0 5 10 15 20 25

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

FLOW (lpm)0 20 40 60 80 100





DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type hydraulic relief valve, which canbe infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for use as apressure limiting device in demanding applications.

OPERATIONThe TS10-26 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to openthe pilot section by offsetting the electrically induced solenoid force. With no currentapplied to the solenoid, the valve will relieve at approximately 100 psi.

The TS10-26 has an optional manual override feature. This allows the valve to be setwhen the electric supply is lost. The manual setting is added to the electric setting, sowhen using the manual override feature to establish a minimum setting, care isrequired to prevent the system from becoming over-pressurized.

FEATURES• Optional Manual Override with Airbleed.• Optional waterproof E-Coils rated up to IP69K.• 12 and 24 volt coils standard.• Industry common cavity.


A: 6.9–207 bar (100–3000 psi) C: 6.9–117 bar (100–1700 psi)B: 6.9–159 bar (100–2300 psi)

Rated Flow: 94.6 lpm (25 gpm), ∆P=13.1 bar (190 psi), Cartridge only,➀ to ➁ coil de-energized

Maximum Pilot Flow: 0.76 lpm (0.2 gpm)Hysteresis: Less than 3%Flow Path: Free Flow: ➀ to ➁ coil de-energized; Relieving: ➀ to ➁ coil energizedTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: VC10-2; See page 9.110.1; Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2N-B; See page 8.650.1Coil Nut: Part No. 4540560;



PWM — 4000144 4000133 4000140


PatentPending

MATERIALS

Cartridge: Weight: 0.25 kg. (0.55 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. Buna NO-rings and polyester elastomer back-ups standard. Optional polyurethaneseals with fluorocarbon back-uprecommended for pressures over240 bar (3500 psi).

Standard Ported Body: Weight: 0.16 kg.(0.35 lbs.); Anodized high-strength 6061T6 aluminum alloy, rated to 240 bar(3500 psi); See page 8.010.1. Ductileiron and steel bodies available; dimen-sions may differ; consult factory.

Standard Coil: Weight: 0.32 kg. (0.7 lbs.);Unitized, thermoplastic encapsulated,Class H high temperature magnetwire;See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fullyencapsulated with rugged external metalshell; Rated up to IP69K with integralconnectors; Note: See page 3.400.1 forall E-Coil retrofit applications.

TO ORDER

TS10-26

2.852.2

Piloted Spool

1.4837.6

3.0176.5

1.2531.8

0.7519.1

0.287.11.63

41.40.133.3

2.0050.8*

*BSP BODY 55.9 mm

1.5038.1

1.2531.8

INCHMILLIMETRE

1.2531.8

ACROSS FLATS

TORQUE–25 ft-lbs(33.9 Nm) max.

MANUAL OVERRIDE (3/16" HEX)

BLEEDSCREW

1.7344.0


INITIAL SETUP:Before operating valve, use the manual override to manually set pressure to 200 to 300 psi. Back out bleed screw 2 to 4 rotations to allow all trapped air to escape. Screw in the bleed screw. Before operating electrically, back out manual override (CCW) until positive stop is reached.

CAUTION:Manual override must be fully backed out (turn CCW using 3/16" hex key wrench) when operating electrically

1.6241.1

1.84DIA.

46.7

E-CoilViewStandard

Coil View

HYDRAFORCE®

DIMENSIONS

TS10-26 __ __ - __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T




207 bar (3000 psi) A159 bar (2300 psi) B117 bar (1700 psi) C

OptionNone (Blank)

Manual Override M

Voltage0 Less Coil








(IP69K Rated)


Patent Pending


USASI/ISO:

SYMBOLS

2.854.1

PERFORMANCE

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)


0 10 20 30 40 50

00 0

50

100

150

200

250

2468

101214161820

40 80 120 160 200

Cartridge & Body: ABC

Body Only


200 Hz PWMRelieving Pressure ➀ to ➁

PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

2500

3000

3500

PR

ES

SU

RE

(ba

r)

0

50

100

150

200

250


A

B

C




0 10 20 30 40 50

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

FLOW (lpm)0 40 80 120 160 200




No Control Current

DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type hydraulic relief valve, which canbe infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for use as apressure limiting device in demanding applications.

OPERATIONThe TS12-26 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to openthe pilot section by offsetting the electrically induced solenoid force. With no currentapplied to the solenoid, the valve will relieve at approximately 100 psi.

FEATURES• Airbleed standard. • Industry common cavity.• Manual Override option. • Optional waterproof E-Coils rated up to IP69K.• 12 and 24 volt coils standard.


A: 5.2–207 bar (75–3000 psi)B: 3.4–138 bar (50–2000 psi)C: 2.1–70 bar (30–1000 psi)

Rated Flow: 189 lpm (50 gpm); See Performance ChartsMaximum Pilot Flow: A: 1.9 lpm (.5 gpm); B: 1.3 lpm (.35 gpm); C: .9 lpm (.25 gpm)Hysteresis: Less than 3%Flow Path: Free Flow: ➀ to ➁ coil de-energized; Relieving: ➀ to ➁ coil energizedTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities







PWM — 4000144 4000133 4000140


PatentPending

TS12-26

2.854.2

Piloted Spool

INITIAL SETUP:Before operating valve, back out bleed screw

2 to 4 rotations to allow all trapped air to escape.Then screw in the bleed screw.

MANUAL OVERRIDEOPTIONAL


1.6241.1

1.84DIA.

46.7

2.9575.1 E-Coil

ViewStandardCoil View

MATERIALS TO ORDER

TS12-26__ __ - __ - __ - __ __ __ __




SAE 10 10TSAE 12 12T





Standard Coil: Weight: 0.32 kg.(0.7 lbs.); Unitized thermoplasticencapsulated, Class H high tempera-ture magnet-wire; See page 3.200.1.


HYDRAFORCE®

DIMENSIONS


Manual Override M

Voltage0 Less Coil








(IP69K Rated)


PatentPending


DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type pressure relief valve, which canbe infinitely adjusted across a prescribed range using a variable electric input.Pressure output is inversely proportional to DC current input. This valve is intendedfor use as a pressure limiting device in demanding applications.

OPERATIONThe TS08-27 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to openthe valve by overcoming the preset induced spring force. With no current applied, thevalve will relieve at ±50 psi of the spring maximum. Applying current to the coilreduces the induced spring force thereby reducing the valve setting. The regulatedpressure is inversely proportional to the input electrical current.

Note: This valve is ideal for hydraulic fan drive applications. Consult factory forelectronic controllers specifically designed for fan drive applications.

FEATURES• 12 and 24 volt coils standard.• Industry common cavity.• Hardened parts for long life.


Minimum Pressure is factory adjusted.A: 207–4.1 bar (3000–60 psi)B: 138–4.1 bar (2000–60 psi)

Rated Flow: 19 lpm/5 gpm; ∆P = 7.8 bar (113.3 psi) ±10%, cartridge only,➀ to ➁ coil energized

Maximum Pilot Flow: 0.76 lpm (0.2 gpm)Hysteresis: Less than 3%Flow Path: Free Flow: ➀ to ➁ coil energized; Relieving: ➀ to ➁ coil de-energizedPressure Rise: A: 40 psi/gpm; B: 50 psi/gpm; C: 28 psi/gpmTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: VC08-2; See page 9.108.1; Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-B; See page 8.650.1

USASI/ISO:

SYMBOLS

2.860.1

PERFORMANCE



PRESSURE DROP VS. FLOW CHARACTERISTICFlow from Port ➀ to Port ➁ with Coil Energized, at Maximum Set Current

PR

ES

SU

RE

(B

AR

)

PR

ES

SU

RE

(P

SI)

FLOW (GPM)

FLOW (LPM)

0 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.00.5

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

0

20

40

60

80

100

120

140

160

0

2

4

6

8

10

Cartridge, Body & Line

Body & Line

TYPICAL RELIEF PRESSURE VS. FLOW CHARACTERISTICTypical Relieving Pressure Port ➀ to Port ➁; Cartridge in Body

FLOW (LPM)

FLOW (GPM)

0 2 4 6 8 10 12 14 16 18

0 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.00.5

0

2040

60

80100

120140

160180

200220

PR

ES

SU

RE

(B

AR

)

PR

ES

SU

RE

(P

SI)

0

400

800

1200

1600

2000

2400

2800

3200

Range A

Range B

Range C

DIMENSIONS

MATERIALS


Standard Ported Body: Weight: 0.16kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); See page8.008.1. Steel and ductile iron bodiesavailable; dimensions may differ;consult factory.

EHPR Series Coil: Weight: 0.11 kg.(0.25 lbs.); Unitized, thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

TO ORDER

TS08-27

2.860.2

TS08-27 __ __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T




Voltage0 Less Coil

12 12 VDC (1.10 amps max.)24 24 VDC (0.55 amps max.)

1.1328.7

1.2331.2

0.88ACROSS

22.2

INCHMILLIMETRE

2.2557.3

2.0050.8

0.7519.1

0.6015.2

0.287.11.62

41.10.133.3

2.00*50.8

* BSP BODY55.9 mm

1.5038.1

1.0927.7

FLATSTORQUE4–5 ft-lbs(5.4–6.8 Nm)max.

0.88ACROSS

22.2FLATS


(24.4–27 Nm)max.

HYDRAFORCE®

(continued)

U.S. Patent 6,267,350

MaximumOperating Pressure

207 bar (3000 psi) A138 bar (2000 psi) B





PERFORMANCE

RELIEF PRESSURE vs. CURRENT (DC) CHARACTERISTIC

Relieving Pressure Port ➀ to Port ➁5.68 lpm (1.5 gpm) Flow using 12VDC Coil, 200 Hz PWM


CURRENT (AMPS)

PR

ES

SU

RE

(B

AR

)

PR

ES

SU

RE

(P

SI)

0

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2

10 20 30 40 50 60 70 80 90 100

0

200

400

600

800

1000

1200

1400

1600

1800

2000

2200

2400

2600

2800

3000

3200

0

20

40

60

80

100

120

140

160

180

200

220

Range A

Range B

Range C


PWM — 4000144 4000133 4000140



USASI/ISO:

SYMBOLS

2.862.1

PERFORMANCE

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)

Pressure Drop vs. Flow CharacteristicFor Flow ➀ to ➁ with Coil Energized

0 5 10 15 20 25

00 0

50

100

150

200

250

2468

101214161820

20 40 60 80 100

Cartridge & Body

Body Only

Relief Pressure vs.Current (DC) Characteristic, 200 Hz PWM


PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

2500

3000

3500

PR

ES

SU

RE

(ba

r)

0

50

100

150

200

250


A

B

C




0 5 10 15 20 25

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

FLOW (lpm)0 20 40 60 80 100



No Current


DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type hydraulic relief valve, which canbe infinitely adjusted across a prescribed range using a variable electric input.Pressure output is inversely proportional to DC current input. This valve is intendedfor use as a pressure limiting device in demanding applications.

OPERATIONThe TS10-27 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to openthe valve by overcoming the preset induced spring force. With no current applied, thevalve will relieve at ±50 psi of the range maximum. Applying current to the coildecreases the induced spring force, thereby reducing the valve setting.


FEATURES• 12 and 24 volt coils standard.• Industry common cavity.• Optional waterproof E-Coils rated up to IP69K.


A: 207–10.3 bar (3000–150 psi)B: 138–10.3 bar (2000–150 psi)C: 69–10.3 bar (1000–150 psi)

Rated Flow: 75.7 lpm (20 gpm), ∆P=14.8 bar (215 psi), Cartridge only,➀ to ➁ coil energized

Maximum Pilot Flow: 0.76 lpm (0.2 gpm)Hysteresis: Less than 3%Flow Path: Free Flow: ➀ to ➁ coil energized; Relieving: ➀ to ➁ coil de-energizedTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities








PWM — 4000144 4000133 4000140


MATERIALS TO ORDER

TS10-27

2.862.2

Piloted Spool

TS10-27__ - __ - __ - __ __ __ __




SAE 6 6TSAE 8 8T



1.4837.6

2.5664.9

1.2531.8

0.7519.1

0.287.11.63

41.40.133.3

2.0050.8*

*BSP BODY 55.9 mm

1.5038.1

1.2531.8

INCHMILLIMETRE

1.0025.4

ACROSS FLATS


1.7344.0



1.6241.1

1.84DIA.

46.7

E-CoilViewStandard

Coil View

Cartridge: Weight: 0.18 kg. (0.4 lbs.); Steelwith hardened work surfaces. Zinc-platedexposed surfaces. Buna N O-rings andpolyester elastomer back-ups standard.Optional polyurethane seals withfluorocarbon back-up recommended forpressures over 240 bar (3500 psi).

Standard Ported Body: Weight: 0.16 kg.(0.35 lbs.); Anodized high-strength6061 T6 aluminum alloy, rated to 240 bar(3500 psi); See page 8.010.1. Ductileiron and steel bodies available; dimen-sions maay differ; consult factory.

Standard Coil: Weight: 0.27 kg. (0.6 lbs.);Unitized thermoplastic encapsulated,Class H high temperature magnet-wire;See page 3.200.1.


HYDRAFORCE®

DIMENSIONSU.S. Patent 6,267,350

Voltage0 Less Coil10 10 VDC (1.30 amps max.)12 12 VDC (1.10 amps max.)20 20 VDC (0.65 amps max.)24 24 VDC (0.55 amps max.)







(IP69K Rated)



DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type hydraulic relief valve, which canbe infinitely adjusted across a prescribed range using a variable electric input.Pressure output is inversely proportional to DC current input. This valve is intendedfor use as a pressure limiting device in demanding applications.

OPERATIONThe TS12-27 blocks flow from ➀ to ➁ until sufficient pressure is present at ➀ to openthe pilot section by overcoming the induced spring force. Applying current to the coilproportionally decreases the pressure required to open the valve from ➀ to ➁.


FEATURES• Hardened parts for long life.• 12 and 24 volt coils standard.• Industry common cavity.• Optional waterproof E-Coils rated up to IP69K.


A: 207–10.34 bar (3000–150 psi)B: 138–10.34 bar (2000–150 psi)C: 69–10.34 bar (1000–150 psi)

Rated Flow: 186.3 lpm (50 gpm), ∆P=16.4 bar (238 psi), Cartridge only,➀ to ➁ coil energized

Maximum Pilot Flow: 0.76 lpm (.2 gpm)Hysteresis: Less than 3%Flow Path: Free Flow: ➀ to ➁ coil energized; Relieving: ➀ to ➁ coil de-energizedTemperature: -40 to 120°C (-40 to 250°F) with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities





USASI/ISO:

SYMBOLS

2.864.1

PERFORMANCE

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)

Pressure Drop vs. Flow CharacteristicFor Flow ➀ to ➁ with Coil Energized

0 10 20 30 40 50

00 0

50

100

150

200

250

2468

101214161820

40 80 120 160 200

Cartridge & Body

Body Only

Relief Pressure vs.Current (DC) Characteristic, 200 Hz PWM


PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

2500

3000

3500

PR

ES

SU

RE

(ba

r)

0

50

100

150

200

250


A

B

C




0 10 20 30 40 50

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

FLOW (lpm)0 40 80 120 160 200




No Control Current




0-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140


MATERIALS TO ORDER

TS12-27

2.864.2

TS12-27__ - __ - __ - __ __ __ __




SAE 10 10TSAE 12 12T




1.6241.1

1.84DIA.

46.7

2.5564.9

E-CoilView

StandardCoil View

Cartridge: Weight: 0.56 kg. (1.23 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. BunaN O-rings and TFE back-upsstandard.




HYDRAFORCE®

DIMENSIONS

U.S. Patent 6,267,350









(IP69K Rated)

TS80-30 Proportional Reducing/Relieving Valve

USASI/ISO:

SYMBOLS

2.872.1

PERFORMANCE

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)

Pressure Drop vs. Flow CharacteristicFor Flow ➀ to ➂ with Coil De-energized

0 1 2 3 4 5 6 6.5

00 0

25

50

75

100

125

123456789

10

5 10 15 20 25

Regulated Pressurevs. Current Characteristic, 200 Hz PWM

PR

ES

SU

RE

(ps

i)

0

50

100

150

200

250

PR

ES

SU

RE

(ba

r)

0

5

10

15

200 0.1 0.2 0.3 0.4 0.5 0.6 0.7

% of Maximum Control Current

Control Current (Amps), Smooth DC

0 2010 30 50 70 9040 60 80 100

Reduced Pressure vs. FlowRelieving Pressure ➀ to ➂

FLOW (gpm)56 4 3 2 1 0

PR

ES

SU

RE

(ps

i)

150

100

0

50

250

200

300

350

PR

ES

SU

RE

(ba

r)

15

0

5

20

25

10

FLOW (lpm)25 5101520 0

0.55 amp

0.40 amp

0.30 amp

0 amp

0.70 amp

DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type reducing/relieving valve, whichcan be infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for use as apressure control device in demanding applications.

OPERATIONThe TS80-30 allows free flow from ➀ to ➂ when no current is applied to the coil.When the coil is energized, ➁ is connected to ➀. Increasing current applied to the coilwill increase the control (reduced) pressure proportionally. If pressure at ➀ exceedsthe setting induced by the coil, pressure from ➀ is relieved to ➂.

Note: Back pressure on port ➂ becomes additive to the pressure setting at a 1:1 ratio.

FEATURES• Airbleed standard.• 12 and 24 volt coils standard.• Industry common cavity.• Optional waterproof E-Coils rated up to IP69K.

RATINGSMaximum Inlet Pressure: 40 bar (580 psi)Maximum Control Current: 0.65 amps for 12 VDC coil; 0.33 amps for 24 VDC coilReducing/Relieving Pressure Range from Zero to Maximum Control Current:

0–20 bar (0–290 psi)Rated Flow: 20.8 lpm (6.0 gpm), ∆P=7.6 bar (110 psi), Cartridge only,

➀ to ➂ coil de-energizedMaximum Pilot Flow: 0.76 lpm (0.2 gpm)Hysteresis: Less than 3%Flow Path: Free Flow: ➀ to ➂ coil de-energized; Reduced: ➁ to ➀ coil energized;

Relieving: ➀ to ➂ coil energizedTemperature: -40 to 120°C (-40 to 250°F), with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: VC10-3; See page 9.110.1; Cavity Tool: CT10-3XX; See page 8.600.1Seal Kit: SK10-3X-BM; See page 8.650.1Coil Nut: Part No. 7004410;


Reduced Pressure vs. FlowReducing Pressure ➁ to ➀

FLOW (gpm)5 643210

PR

ES

SU

RE

(ps

i)

150

100

0

50

250

200

300

350

PR

ES

SU

RE

(ba

r)

15

0

5

20

25

10

FLOW (lpm)0 1020 15 20 25

0.55 amp

0.40 amp

0.30 amp

0.70 amp


Note: This product, the TS80-30, is obsolete effective Oct. 2005.Consult the Hydraforce applications group for alternatives thatwill meet your system requirements.

TS80-30

2.872.2

MATERIALS TO ORDER

TS80-30 - __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T

3/8 in. BSP* 3B1/2 in. BSP* 4B*BSP Body;U.K. Mfr. Only

BLEEDING VALVE:Before operating valve, remove coil nut and set pressure to 100–200 psi. Back out bleeder 2 to 4 rotations to allow all trapped air to escape. Retighten bleeder screw and replace coil nut before operating valve.

Bleeder Screw

Top View: Coil Nut Removed

TORQUE: 5 ft-lbs(6.8 Nm) max.

1.4035.6

1.41 DIA.35.8

2.2557.2

E-CoilView

StandardCoil View





HYDRAFORCE®

DIMENSIONS









(IP69K Rated)


PWM — 4000144 4000133 4000140


Note: This product, the TS80-30,is obsolete effective Oct. 2005.Consult the Hydraforce applica-tions group for alternatives thatwill meet your systemrequirements.

TS98-30 Proportional Electric Reducing/Relieving

2.882.1


OPERATIONWithout applied current, the TS98-30 allows bidirectional flow from ➂ to ➃ whileblocking ➁. When the coil is energized, ➂ is connected to ➁, and pressure at ➂ iscontrolled proportional to the amount of current applied to the coil. If pressure at ➂exceeds the setting induced by the coil, pressure is relieved to ➃.

Back pressure on port ➃ becomes additive to the pressure setting at a 1:1 ratio.

Note: This product may be customized for special OEM performance characteristics.Consult factory.

FEATURES• 12 and 24 volt coils standard.• Optional waterproofed E-Coils rated up to IP69K.

RATINGSMaximum Inlet Pressure at Port ➁: 24 bar (350 psi)Maximum Control Current: 0.70 amps for 12 VDC coil; 0.35 amps for 24 VDC coilDeadband: 0.150 amps @ 12 VDC; 0.075 amps @ 24 VDCHysteresis: 3.0% PWMReducing/Relieving Pressure Range from Zero to Maximum Control Current:

0–20.7 bar (0–300 psi)Rated Flow: 30 lpm (8 gpm) at 45 psid port ➂ to ➃ with coil de-energizedMaximum Pilot Flow: 0.4 lpm (0.12 gpm)Flow Path: Free Flow: ➂ to ➃ bidirectional coil de-energized; Reduced: ➁ to ➂ coil

energized; Relieving: ➂ to ➃ coil energized; Port ➀ is not plumbed externallyTemperature: -30 to 175°C (-20 to 350°F), with standard Fluorocarbon sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: VC98-3; See page 9.110.1; Cavity Tool: CT98-3XX; See page 8.600.1Seal Kit: SK90-3V; See page 8.650.1Coil Nut: Part No. 7004410;


USASI/ISO:

SYMBOLS

PERFORMANCE

3

2

1

4

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)

Pressure Drop vs. Flow CharacteristicFor Flow ➂ to ➃ with Coil De-energized

—— Reducing; – – – Relief

0 1 2 63 54 7 8 9 10

00 0

20

140

120

40

60

80

100

2

4

6

8

10

5 10 2015 3025 35

Cartridge & Body

Cartridge Only

PR

ES

SU

RE

(ps

i)

0

50

100

150

200

250

300

350

PR

ES

SU

RE

(ba

r)

0

5

10

15

20

25


Reduced Pressure vs. Current CharacteristicFor a Regulated Pressure Range of

0–20 bar (0–300 psi) with Input Pressure at ➁Control Current: 300 Hz


Reducing/Relieving Pressure vs. Flow CharacteristicRegulated Pressure Range: 0–20 bar (0–290 psi) with 24 bar (350 psi) InputPressure at ➂ for Various Control Currents (∆P Shown for Cartridge & Body)

FLOW (gpm)9 78 6 5 4 3 2 1 97 85 643210

PR

ES

SU

RE

(ps

i)

150

0

50

100

200

250

300

350

PR

ES

SU

RE

(ba

r)

10

0

5

15

20

25

FLOW (lpm)2530 20 15 10 5 0 5 10 15 20 25 30

Reducing Pressure ➁ to ➂Relieving Pressure ➂ to ➃

0.65 Amps

0.4 Amps

0.525 Amps

0.275 Amps


2.884.1

DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type reducing/relieving valve, which can be infi nitely adjusted across a prescribed range using a variable electric input. Pressure output is proportional to DC current input. This valve is intended for use as a pressure control device in demanding applications.

OPERATIONWithout applied current, the TS90-31 allows fl ow from ➂ to ➃ while blocking ➁. When the coil is energized, ➂ is connected to ➁, and pressure at ➂ is controlled proportional to the amount of current applied to the coil. If pressure at ➂ exceeds the setting induced by the coil, pressure is relieved to ➃.Back pressure on port ➃ becomes additive to the pressure setting at a 1:1 ratio.Note: This product may be customized for special OEM performance characteristics. Consult factory.

FEATURES• 12 and 24 volt coils standard.• Optional waterproofed E-Coils rated up to IP69K.

RATINGSMaximum Operating Pressure at Ports 1 and 2: 207 bar (3000 psi)Maximum Tank Pressure at Port 4: 69 bar (1000 psi)Regulated Pressure Range from Zero to Max. Control Current:

0 to 137.9 bar (2000 psi)Maximum Control Current: E-Coils: 0.88 amps for 12 VDC coil; 0.44 amps for 24

VDC coil; D-Coils: 0.68 amps for 12 VDC coil; 0.34 amps for 24 VDC coilDeadband: 0.150 amps @ 12 VDC; 0.075 amps @ 24 VDCHysteresis: 3.0% PWMRated Flow: 38 lpm (10 gpm)Maximum Pilot Flow: 0.85 lpm (0.23 gpm) with No CurrentFlow Path: Free Flow: ➂ to ➃ coil de-energized; Reduced: ➁ to ➂ coil energized;

Relieving: ➂ to ➃ coil energized; Port ➀ is not plumbed externallyTemperature: -40 to 100°C (-40 to 212°F) with standard Buna N seals

-26 to 204°C (-15 to 400°F) with Fluorocarbon sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation Recommendation: When possible, the valve should be mounted below

the reservoir oil level. This will maintain oil in the armature preventing trapped air instability. If this is not feasible, mount the valve horizontally for best results.

Cavity: VC98-3; See page 9.110.1; Cavity Tool: CT98-3XX; See page 8.600.1Seal Kit: SK90-3X-BM; See page 8.650.1Coil Nut: Part No. 4540560

USASI/ISO:

SYMBOLS

PERFORMANCE


HYDRAFORCE.com®

3

2

1

4

FLOW lpm/gpm

Typical Pressure Drop vs. Flow

PR

ES

SU

RE

bar

/psi

0

1.7/25

3.4/50

5.2/75

6.9/100

8.6/125

10.3/150

12.1/175

3810

3810

308

308

236

236

154

154

7.62

7.62

0

Relieving PressurePort 3 to 4

Coil Current: 0A

Cartridge, Body & Line ——; Body & Line – - – -Reducing Pressure

Port 2 to 3Coil Current: 0.5A

PR

ES

SU

RE

bar

/psi

0

34.5/500

68.9/1000

103.4/1500

137.9/2000

172.4/2500Control Current (amps) with 100 Hz Dither

Current amps0.20.1 0.60.4 0.70.3 0.5 0.8

Inlet Pressure 172 bar (2500 psi) at No FlowReducing Pressure vs. Current

Typical Reducing/Relieving Pressure vs. FlowFor a Regulated Pressure with 172.4 bar (2500 psi) Inlet Pressure

for Various Percentages of Nominal Control Currents

PR

ES

SU

RE

bar

/psi

68.9/1000

0

34.5/500

103.4/1500

137.9/2000

172.4/2500

FLOW lpm/gpm

30.38

30.38

37.910

37.910

22.76

22.76

15.14

15.14

7.62

7.62

0

Relieving Pressure:(Differential – Body & Cartridge)

Reducing Pressure:

100% Control Current

75% Control Current

50% Control Current

25% Control Current

RP



DESCRIPTIONA solenoid-operated, 5-way, 3-position, proportional, screw-in hydraulic cartridge valve with integral load-sense port.

OPERATIONWhen de-energized, the SP10-57C blocks fl ow to all ports. When coil #1 is energized, fl ow is allowed from ➄ to ➁, and from ➃ to ➂. When coil #2 is energized, fl ow is allowed from ➄ to ➃, and from ➁ to ➂. Load sense is connected to port ➄ when the spool is in shifted positions.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations• Cartridges are voltage interchangeable.• Optional manual override.• Optional waterproof E-Coils rated up to IP69K.


7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1; Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-coils: Part No. 4539700

SYMBOLS

2.132.1

USASI:

ISO:


5

4

3

2

1


15.1/4

22.7/6

7.5/2

3.8/1

11.4/3

18.9/5

01.0 1.0 1.51.5 0.5 0.50


FLO

W lp

m/g

pm

Top Coil


(for other voltages consult factory)Bottom Coil


17.2/250

15.5/225

13.8/200

12.1/175

10.3/150

8.6/125

6.9/100

3.4/50

5.2/75

1.7/25

3.81

7.62

11.43

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


SP10-57C Spool, 5-Way, 3-Position . . .

HYDRAFORCE.com®


RP



DIMENSIONS

SP10-57C

2.132.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.


1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS

691000


FLO

W lp

m/g

pm

1382000

2073000

15.1/4

18.9/5

22.7/6

11.4/3

7.6/2

3.8/1

1.0 AMP

0.75 AMP

0.50 AMP




®HYDRAFORCE

HYDRAFORCE.com®

SP10-57C__ - __ __ __ - __ - __ __ __ __ __

TO ORDER










MATERIALS



Standard Coil: Weight each: 0.27 kg. (0.60 lbs.); Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1

E-Coil: Weight each: 0.41 kg. (0.9 lbs.); Perfect wound, fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors. See page 3.400.1 for all E-Coil retrofi t applications.


Option None (Blank)



RP



TS90-31

2.884.2

Valve, Internally Piloted

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.25 kg. (0.55 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. O-rings standard.


Standard Coil: Weight: 0.32 kg. (0.70 lbs.) Unitized thermoplastic encapsulated, Class H high temperature magnet-wire. See page 3.200.1

E-Coil: Weight: 0.41 kg. (0.9 lbs.) Perfect wound, fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors.Note: See page 3.400.1 for all E-Coil retrofi t applications.

TO ORDER

TS90-31 - __ - __ - __ __ __ __


Seals Buna N N Fluorocarbon V


Note: This valve uses a 10-size coil and the VC98-3 cavity, which is a variation of a 10-size cavity.

PERFORMANCE (continued)

Voltage Less Coil 0 12 VDC (0.88 amps max.) 12 24 VDC (0.44 amps max.) 24Consult factory for other voltages

Termination Std. D-Coil DS Dual Spades DG DIN 43650 DL Leadwires (2) DL/W Leads w/Weatherpak® Connectors DR Deutsch DT04-2P

Termination E-Coil EG DIN 43650 (IP65 Rated) EL Leadwires (2) (IP69K Rated) ER Deutsch DT04-2P (IP69K Rated) EY Metri-Pack® 150 (IP69K Rated) EJ Amp Jr. Timer (IP69K Rated)

®HYDRAFORCE

HYDRAFORCE.com®


543210

-1-2-3-4-5-6-7-8-9

-10-11-12

Typical Frequency Response Curves

GA

IN (

dB)

-180

-90

-45

0

-135

PH

AS

E (

degr

ees)

1 2

FREQUENCY (Hz)Signal 50% ±50% - - - - - -Signal 75% ±15% ———

Signal 90% ±10% – – – –

3 4 5 6 7 89 10 20 30 40 50 70

TIME seconds

PR

ES

SU

RE

bar

/psi

1.38 1.42 1.46 1.50 3.60 3.70 3.80 3.90

0

34.5/500

68.9/1000

103.4/1500

137.9/2000

172.4/2500

Typical Step Response CurveReducing Pressure Shown; No FlowInlet Pressure: 172.4 bar/ 2500 psi

12 VDC E-Series Coil

1.2531.8

1.2531.8 2.50

63.5

1.3634.5

2.8472.1

3.2582.6

2.0050.8

0.287.1

1.9950.5

4

2

0.7418.8

0.256.4

INCHMILLIMETRE

3

2.3559.6

1.7344.0

2.9574.9

2.6266.5 3

2

1

4

430μScreen

1.6241.1

1.84DIA.

46.7

TORQUE8.6 to

9.4 ft-lbs(11.6 to 12.8 Nm)

TORQUE25 to

27 ft-lbs(34 to

36.7 Nm)

StandardCoil View

E-CoilView

RP



TS98-30

2.882.2

Valve w/Internally Piloted Spool

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.25 kg. (0.55 lbs.); Steelwith hardened work surfaces. Zinc-platedexposed surfaces. O-rings standard.

Standard Ported Body: Weight: 0.34 kg.(0.75 lbs.); Anodized high-strength 6061T6 aluminum alloy, rated to 240 bar(3500 psi); See page 8.010.1. Ductile ironand steel bodies available; dimensionsmay differ; consult factory.


E-Coil: Weight: 0.14 kg. (0.3 lbs.); Perfectwound, fully encapsulated with ruggedexternal metal shell; Rated up to IP69Kwith integral connectors;Note: See page 3.400.1 for all E-Coilretrofit applications.

TO ORDER

TS98-30 - __ - __ - __ __ __ __

E-CoilView

1.2531.8

1.2531.8 2.50

63.5

1.3634.5

2.8472.1

3.2582.6

2.0050.8

0.287.1

1.9950.5

4

2

0.7418.8

0.256.4

INCHMILLIMETRE

3

1.8847.8

1.3033.0

2.2557.2

2.6266.5 3

2

1

4

1.0025.4

ACROSS

250 MICRONSCREEN

FLATS

TORQUE20 ft-lbs(27.1 Nm)max.

TORQUE5 ft-lbs

(6.8 Nm) max.

1.4035.6

1.41DIA.

35.8

StandardCoil View


SAE 6 6TSAE 8 8T

HYDRAFORCE®

SealsFluorocarbon V


2

0

-2

-4

-6

-8

-10

-12

-180

-90

2 4 6

FREQUENCY (Hz)


Signal 50% ±50%Signal 70% ±25%

Signal 95% ±5%Signal 75% ±15%

8 10 20 30 40 50 60

-45

0

-135

GA

IN (

dB)

PH

AS

E (

degr

ees)

TIME (msec.)1006050403020100 20 30 40 50

0

500

1000

CU

RR

EN

T (

mA

)

0

6.9100

13.8200

20.7300

PR

ES

SU

RE

(ba

r/ps

i)

Inlet Pressure

Current Input

Res

pons

e

Typical Step Response Curve

DIMENSIONS (continued)

VoltageLess Coil 0

10 VDC (0.84 amps max.) 1012 VDC (0.70 amps max.) 1220 VDC (0.42 amps max.) 2024 VDC (0.35 amps max.) 24

Consult factory for other voltages






(IP69K Rated)


PWM — 4000144 4000133 4000140




OPERATIONWithout applied current, the TS98-31 allows bidirectional flow from ➂ to ➃ whileblocking ➁. When the coil is energized, ➂ is connected to ➁, and pressure at ➂ iscontrolled proportional to the amount of current applied to the coil. If pressure at ➂exceeds the setting induced by the coil, pressure is relieved to ➃.



FEATURES• 12 and 24 volt coils standard.• Optional waterproof E-Coils rated up to IP69K.

RATINGSMaximum Inlet Pressure at Port ➁: 207 bar (3000 psi)Maximum Control Current: 0.70 amps for 12 VDC coil; 0.35 amps for 24 VDC coilDeadband: 0.150 amps @ 12 VDC; 0.075 amps @ 24 VDCHysteresis: 3.0% PWMReducing/Relieving Pressure Range from Zero to Maximum Control Current:

0–138 bar (0–2000 psi)Rated Flow: 11.4 lpm (3 gpm) at 45 psid port ➂ to ➃ with coil de-energizedMaximum Pilot Flow: 0.4 lpm (0.12 gpm)Flow Path: Free Flow: ➂ to ➃ bidirectional coil de-energized; Reduced: ➁ to ➂ coil

energized; Relieving: ➂ to ➃ coil energized; Port ➀ is not plumbed externallyTemperature: -30 to 175°C (-20 to 350°F), with standard Fluorocarbon sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: VC98-3; See page 9.110.1; Cavity Tool: CT98-3XX; See page 8.600.1Seal Kit: SK90-3V; See page 8.650.1Coil Nut: Part No. 7004410;


USASI/ISO:

SYMBOLS

2.890.1

PERFORMANCE

3

2

1

4

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)

Pressure Drop vs. Flow CharacteristicFor Flow ➂ to ➃ with Coil De-energized

0 0.5 1 1.5 2 2.5 3 3.5

00 0

5

10

15

20

25

0.5

1.0

1.5

2.0

2.5 7.55 12.510 15

Cartridge & Body

Cartridge Only

PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

PR

ES

SU

RE

(ba

r)

0

40

20

60

80

100

120

140

160

% of Maximum Control Current

Control Current (Amps) with 200 Hz Dither

0

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7

2010 30 50 70 9040 60 80 100

Reduced Pressure vs. Current CharacteristicFor a Regulated Pressure Range of

0–134.5 bar (0–1900 psi) with Input Pressure at ➁


Reducing/Relieving Pressure vs. Flow CharacteristicRegulated Pressure Range: 0–134.5 bar (0–1950 psi) with 137.9 bar (2000 psi) Input

Pressure at ➂ for Various Control Currents (∆P Shown for Cartridge & Body)

FLOW (gpm)3.54 3 2.5 2 1.5 1 0.5 3.5 42.5 321.510.50

PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

PR

ES

SU

RE

(ba

r)

40

0

20

60

80

100

120

140

FLOW (lpm)12 101416 8 6 4 2 0 2 4 6 108 1412 16


100% Max. Current

75% Max. Current

50% Max. Current

25% Max. Current

DIMENSIONS

TS98-31

2.890.2


E-CoilView

1.2531.8

1.2531.8 2.50

63.5

1.3634.5

2.8472.1

3.2582.6

2.0050.8

0.287.1

1.9950.5

4

2

0.7418.8

0.256.4

INCHMILLIMETRE

3

1.8847.8

1.3033.0

2.2557.2

2.6266.5 3

2

1

4

1.0025.4

ACROSS

250 MICRONSCREEN

FLATS

TORQUE20 ft-lbs(27.1 Nm)max.

TORQUE5 ft-lbs

(6.8 Nm) max.

1.4035.6

1.41DIA.

35.8

StandardCoil View

HYDRAFORCE®

PERFORMANCE

2 4 6FREQUENCY (Hz)

Signal 50% ±50%

Signal 75% ±15%

Signal 90% ±10%

TEST CONDITIONS:Inlet: 2000 psiReduced Port: Blocked

8 10 20 30 40 50 60

-180

-90

-45

0

-135

PH

AS

E (

degr

ees)

4

2

0

-2

-4

-6

-8

-10

-12

GA

IN (

dB)


TIME (msec.)10050403020100 20 30 40 50

0

0.2

0.4

0.6

0.8

CU

RR

EN

T (

Am

ps)

0

35500

701000

1031500

1382000

PR

ES

SU

RE

(ba

r/ps

i)

Pressure

Current


MATERIALS

Cartridge: Weight: 0.25 kg. (0.55 lbs.); Steelwith hardened work surfaces. Zinc-platedexposed surfaces. O-rings standard.

Standard Ported Body: Weight: 0.34 kg.(0.75 lbs.); Anodized high-strength 6061T6 aluminum alloy, rated to 240 bar(3500 psi); See page 8.010.1. Ductile ironand steel bodies available; dimensionsmay differ; consult factory.


E-Coil: Weight: 0.14 kg. (0.3 lbs.); Perfectwound, fully encapsulated with ruggedexternal metal shell; Rated up to IP69Kwith integral connectors;Note: See page 3.400.1 for all E-Coilretrofit applications.

TO ORDER

TS98-31 - __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T

SealsFluorocarbon V


VoltageLess Coil 0

10 VDC (0.84 amps max.) 1012 VDC (0.70 amps max.) 1220 VDC (0.42 amps max.) 2024 VDC (0.35 amps max.) 24







(IP69K Rated)


PWM — 4000144 4000133 4000140



USASI/ISO:

SYMBOLS

2.900.1

PERFORMANCE

DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type reducing/relieving valve, whichcan be infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for use as apressure limiting device in demanding applications.

OPERATIONThe TS10-36 allows flow from ➁ to ➀ until sufficient pressure is present at ➀ to openthe pilot section by offsetting the electrically induced solenoid force. Increasingelectric current will increase the control (reduced) pressure at ➀. With no currentapplied to the solenoid, the valve will maintain pressure at ➀ at approximately100 psi, regardless of pressure at ➁.

The TS10-36 has an optional manual override feature. This allows the valve to be setwhen the electric supply is lost. The manual setting is added to the electric setting, sowhen using the manual override feature to establish a minimum setting, care isrequired to prevent the system from becoming over-pressurized.

FEATURES• Manual override option. • Industry common cavity.• Airbleed option. • Optional waterproof E-Coils rated up to IP69K.• 12 and 24 volt coils standard.


A: 6.9–207 bar (100–3000 psi); B: 6.9–159 bar (100–2300 psi)C: 6.9–117 bar (100–1700 psi)

Rated Flow: 56.8 lpm (15 gpm), ∆P=22.8 bar (330 psi), Cartridge only,➀ to ➂ coil de-energized

Maximum Pilot Flow: 0.76 lpm (0.2 gpm)Flow Path: Free Flow: ➀ to ➂ coil de-energized; Reduced: ➁ to ➀ coil energized;

Relieving: ➀ to ➂ coil energizedTemperature: -40 to 120°C (-40 to 250°F), with standard Buna N sealsFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: VC10-3; See page 9.110.1; Cavity Tool: CT10-3XX; See page 8.600.1Seal Kit: SK10-3N-BM; See page 8.650.1Coil Nut: Part No. 4540560;



FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)


0 3 6 9 12 15

00 0

100

500

400

200

300

6

12

18

24

30

36

10 20 4030 50 60

Cartridge & Body

Cartridge Only

Body Only

Typical Relieving/Reducing Pressure vs. Flow CharacteristicTypical Relieving Pressure at Various %’s of Maximum Control Current

Pressure Range “A” (207 bar/3000 psi); Cartridge in Body

FLOW (gpm)15 12 9 6 3 15129630

% o

f MA

X. R

ED

UC

ED

PR

ES

SU

RE

50

0

25

75

100

125

% o

f MA

X. R

ED

UC

ED

PR

ES

SU

RE

50

0

25

75

100

125

FLOW (lpm)60 50 40 30 20 10 0 10 20 30 40 50 60



75% Max. Control Current 75% Max. Control Current

50% Max. Control Current 50% Max. Control Current

25% Max. Control Current25% Max. Control CurrentB & C Limited to 18.9 lpm (5 gpm)

Reducing Pressure ➁ to ➀Relieving Pressure ➀ to ➂

PatentPending

PERFORMANCE

TS10-36

2.900.2


MATERIALS TO ORDER

1.6241.1

1.84DIA.

46.71.4837.6

3.0276.7

1.8146.0

1.2531.8

1.2531.8 2.50

63.5

1.3634.5

0.287.12.00

50.80.256.4

2.6266.5

2.1253.8

0.7418.8

1.2531.8

ACROSS FLATS


MANUALOVERRIDE(3/16" HEX)

BLEEDSCREW

1.7344.0

TORQUE–10-12 ft-lbs(14-16 Nm) max.

INITIAL SETUP:Before operating valve, use the manual override to manually set pressure to 200 to 300 psi. Back out bleed screw 2 to 4 rotations to allow all trapped air to escape. Screw in the bleed screw. Before operating electrically, back out manual override (CCW) until positive stop is reached.

CAUTION:Manual override must be fully backed out (turn CCW using using 3/16" hex key wrench) when operating electrically.

INCHMILLIMETRE

StandardCoil View

E-CoilView

Cartridge: Weight: 0.25 kg. (0.55 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces.Buna N O-rings and polyester elas-tomer back-ups standard. Optionalpolyurethane seals with fluorocarbonback-up recommended for pressuresover 240 bar (3500 psi).




HYDRAFORCE®

(continued) DIMENSIONSRelief Pressure

vs. Current (DC) Characteristic200 Hz PWM

Reducing Pressure ➁ to ➀

PR

ES

SU

RE

(ba

r/ps

i)

0

50725

1001450

1502175

2002900

2503525


A

B

C

TS10-36 __ __ - __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T





OptionNone (Blank)

Manual Override M

Voltage0 Less Coil








(IP69K Rated)



PWM — 4000144 4000133 4000140


Patent Pending


USASI/ISO:

SYMBOLS

2.901.1

PERFORMANCE

DESCRIPTIONA screw-in, cartridge-style, pilot-operated, spool-type reducing/relieving valve, whichcan be infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for use as apressure limiting device in demanding applications.

OPERATIONThe TS12-36 allows flow from ➁ to ➀ until pressure at ➀ equals the setting deter-mined by the coil current. Port ➂ is typically connected to the reservoir. If externalload increases the pressure at ➀ beyond this setting, pressure is relieved by allowingflow from ➀ to ➂. Minimum pressure at ➀ without any current is 100 psi.

If external circuitry allows the pressure at ➁ to fall below the pressure at ➀, the valvewill allow free flow from ➀ to ➁ regardless of the setting of the valve or the amount ofcurrent in the coil.

FEATURES• Optional airbleed screw. • 12 and 24 volt coils, standard or optional waterproofed.

RATINGSMaximum Operating Pressure: Ports ➀ and ➁: 276 bar (4000 psi)Maximum Tank Pressure: Port ➂: 68.9 bar (1000 psi); Note: Tank pressure is

additive to regulated pressure.Reduced Pressure Range from Zero to Maximum Controlled Current:

A: 6.9–207 bar (100–3000 psi); B: 6.9–172 bar (100–2500 psi)C: 6.9–138 bar (100–2000 psi)

Maximum Pilot Flow and Leakage: 0.49 lpm (0.13 gpm) with max. control currentand with inlet pressure at 276 bar (4000 psi) at regulated flow of 3.8 lpm (1 gpm).

Flow Path: Free Flow: ➀ to ➂ coil de-energized; Reducing: ➁ to ➀ coil energized;Relieving: ➀ to ➂ coil energized

Performance Life: Less than 5% change in the slope of the pressure vs currentcharacteristics over one million cycles.

Hysteresis: Less than 3%.Temperature: -40 to 120°C (-40 to 250°F) with Buna N seals.Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: VC12-3; See page 9.110.1; Cavity Tool: CT12-3XX; See page 8.600.1Seal Kit: SK12-3X-BM; See page 8.650.1Coil Nut: Part No. 4526330;



2

1

3

Reducing Pressure vs. Currentfor Flow @ 0 gpm; Port 2 to Port 1

with 200 Hz PWM Controller

PR

ES

SU

RE

(ps

i)

0

500

1000

1500

2000

2500

3000

3500

PERCENT OF MAXIMUM CONTROL CURRENT0 10 20 30 40 50 60 70 80 90 100

PR

ES

SU

RE

(ba

r)

0

50

100

75

25

150

200

250

175

125

A

B

C

FLO

W (

lpm

)

FLO

W (

gpm

)

0

0.02

0.04

0.06

0.08

0.10

0

0.1

0.2

0.3

PERCENT OF MAXIMUM CURRENT

Typical Pilot Flow & Leakage vs. Current241 bar (3500 psi) Inlet Pressure

at 3.8–37.8 lpm (1–10 gpm)with 200 Hz PWM Controller

25 50 75 100

Typical Pressure vs. Flow at Maximum Current for Pressure options A, B and CBody & Line Relieving ∆P: 4.5 bar @ 189.3 lpm (65 psi @ 50 gpm)Body & Line Reducing ∆P: 4.8 bar @ 189.3 lpm (70 psi @ 50 gpm)

Typical Pressure Drop vs. Flow (Cartridge & Body)

FLOW (gpm)

PR

ES

SU

RE

(ps

i)

PR

ES

SU

RE

(ba

r)

FLOW (lpm)0

0102030400

500

1000

1500

1500

2000

2500

3000

3500

50 10 20 30 40 500

50

100

75

25

150

200

250

175

125

4080

A

A

B

C

B

C

120160 40 80 120 160

Relieving Pressure (Differential)

Relieving Pressure (Port 1 to Port 3)Coil De-energized

Reducing Pressure (Port 2 to Port 1)Coil Energized to 1.26 Amps

Reducing Pressure (Gauge)

PatentPending

DIMENSIONS

TS12-36

2.901.2


MATERIALS TO ORDER

TS12-36__ __ - __ - __ - __ __ __ __

MaximumReducingPressure






Voltage0 Less Coil*

12 12 VDC24 24 VDC*BSP Body; U.K. Mfr. Only

1.4837.6

2.9574.9

1.2531.8

ACROSS FLATS

0.7519.1

ACROSS FLATS

TORQUE33–37 ft-lbs(45–50 Nm) max.

BLEED SCREW1.7344.0

TORQUE7–10 ft-lbs (9.5–13.6 Nm) max.

INITIAL SETUP:Before operating valve, back out bleed screw 2 to 4 rotations to allow all trapped air to escape. Then screw in the bleed screw.


INCHMILLIMETRE

2.7870.6

1.6241.1

E-CoilView

Standard Coil View

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

3

1

2

1

3

1.84 (46.7)DIA.

Cartridge: Weight: 0.30 kg. (0.66 lbs.);Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-ringsand polyester elastomer back-upsstandard. Optional polyurethane sealswith fluorocarbon back-up recommendedfor pressures over 240 bar (3500 psi).

Standard Ported Body: Weight: 0.23 kg.(0.50 lbs.); Anodized high-strength 6061T6 aluminum alloy, rated to 240 bar(3500 psi); See page 8.010.1. Ductileiron and steel bodies available; dimen-sions may differ; consult factory.



HYDRAFORCE®


Bleed Screw S

PERFORMANCE (cont’d)

Typical Frequency Response CurvesFlow at 0 gpm; Inlet Pressure at 241 bar (3500 psi)

Pressure Range at 50% ±40%

GA

IN (

dB)

FREQUENCY (Hz)10.1 2 3 4 5 10 20 30 60

-25

-20

-15

-10

-5

0

5

0

-45

-90

-135

-180

PH

AS

E (

degr

ees)

PHASE

AMPLITUDE

Typical Step Response CurveFlow at 0 gpm, Inlet Pressure at 241 bar (3500 psi)

Voltage Set to Produce 1.1 ampsat Steady State Test Coil (12 VDC)

PR

ES

SU

RE

(ps

i)

2500200015001000500

0

30003500

4000

TIME (ms)0 10 20 30 40 50 60 0 10 20 30 40

CU

RR

EN

T (

mA

)

050010001500

RESPONSE

CURRENT INPUT






(IP69K Rated)


* IncludesCoil nut.


PWM — 4000144 4000133 4000140


Patent Pending

TS98-T34 Proportional Electric Reducing/Relieving

2.950.1


DESCRIPTIONA drop-in, flange-mounted, cartridge-style, pilot-operated, spool-type reducing/relieving valve, which can be infinitely adjusted across a prescribed range using avariable electric input. Pressure output is proportional to DC current input. This valveis intended for use as a pressure control device in demanding applications.

OPERATIONWithout applied current, the TS98-T34 allows bidirectional flow from ➂ to ➃ whileblocking ➁. When the coil is energized, ➂ is connected to ➁, and pressure at ➂ iscontrolled proportional to the amount of current applied to the coil. If pressure at ➂exceeds the setting induced by the coil, pressure is relieved to ➃.



FEATURES• Economical drop-in style.• Integral waterproof coil standard.• 12 or 24 VDC coils.• Several push-on termination options.

RATINGSMaximum Inlet Pressure and Regulated Pressure: 30 bar (435 psi)Maximum Control Current: To achieve 20 bar (290 psi) regulated pressure:

0.85 amps for 12 VDC coil; 0.43 amps for 24 VDC coilNote: Regulated pressures up to 29.3 bar (425 psi) can be attained with increasedcurrent values and 30 bar (435 psi) inlet pressure.

Deadband: 0.150 amps @ 12 VDC; 0.075 amps @ 24 VDCHysteresis: 5% PWM for 20 bar (290 psi) control pressureReducing/Relieving Pressure Range from Zero to Maximum Control Current:

0–20.7 bar (0–300 psi)Rated Flow: Port ➂ to ➃ with coil de-energized: 30 lpm (8 gpm)Maximum Pilot Flow: 0.79 lpm (0.21 gpm) with 20.7 bar (300 psi) inletFlow Path: Free Flow: ➂ to ➃ coil de-energized; Reduced: ➁ to ➂ coil energized;

Relieving: ➂ to ➃ coil energized; Port ➀ is not plumbed externallyOil Temperature: -40 to 120°C (-40 to 248°F)Ambient Air Temperature: -40 to 120°C (-40 to 248°F)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities



Cavity: Special; Consult factory; Cavity Tool: Special; Consult factorySeal Kit: SK90-3V; See page 8.650.1

USASI/ISO:

SYMBOLS

PERFORMANCE

FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)

Pressure Drop vs. Flow Characteristic- - - - For Flow ➂ to ➃ with Coil De-energized

—— For Flow ➁ to ➂ with Coil Energized

0 1 2 63 54 7 8 9 10

00 0

20

140

120

40

60

80

100

2

4

6

8

10

5 10 2015 3025 35

160

Cartridge & Body

Cartridge Only

PR

ES

SU

RE

(ps

i)

0

50

100

150

200

250

300

PR

ES

SU

RE

(ba

r)

0

5

10

15

20

% of Maximum Control Currentto achieve 20 bar (290 psi) Regulated Pressure

Note: Regulated pressures up to 29.3 bar (425 psi)can be attained with increased current values

and 30 bar (435 psi) inlet pressure.

0 2010 30 50 70 9040 60 80 100

Reduced Pressure vs. Current CharacteristicWith Inlet Pressure at ➁ of 0–20.7 bar (0–300 psi)

Control Current: 200 Hz Dither

2

1

3

4

Input Sig.w/12V or PCB Metal DIN Rail24V Coil Board Box Mount0-5 VDC 4000194 4000174 4000136

0-10 VDC 4000141 4000182 40001374-20 mA 4000143 4000186 4000139

PWM 4000144 4000133 4000140


TS98-T34

2.950.2


HYDRAFORCE®

PERFORMANCE

MATERIALS

Cartridge including Coil: Weight:0.23 kg. (0.50 lbs.); Steel withhardened work surfaces. Zinc-Nickelplated exposed surfaces; HNBRO-rings standard. Coil is encapsu-lated, class H high-temperaturemagnetwire, with zinc-nickel platedshell.

Special Ported Body: Consult factory.

TO ORDER

TS98-T34__ - __ - __ - __ __ __ __ - __

Voltage12 12 VDC (0.70 amps max.)24 24 VDC (0.35 amps max.)



Reducing/Relieving Pressure vs. Flow CharacteristicRegulated Pressure Range: 0–20 bar (0–290 psi) with 20.7 bar (300 psi) InputPressure at ➁ for Various Control Currents (∆P Shown for Cartridge & Body)

FLOW (gpm)9 78 6 5 4 3 2 1 97 85 643210

PR

ES

SU

RE

(ps

i)

150

0

50

100

200

250

300

350

PR

ES

SU

RE

(ba

r)

10

0

5

15

20

25

FLOW (lpm)253035 20 15 10 5 0 5 10 15 20 25 30 35


94% I-Max.

82% I-Max.

70% I-Max.

59% I-Max.

47% I-Max.

35% I-Max.24% I-Max.1.16

DIA.29.5

1.9549.6

2.5965.7

INCH

MILLIMETRE

2

1

3

4

MOUNTING SCREWTORQUE: 2 to 3 ft-lbs(3 to 4 Nm)1.28

30°

32.5

0.8521.5

1.1027.8

DIMENSIONS

TerminationDJ Amp Junior TimerDY Metri-Pack® 150.2ADR Deutsch DT04-2P

Diode(Blank) None

Z Zener Diode

SealsHydrogenated Nitrile N

(HNBR)

OptionNone (Blank)

Inlet Port Screen S

(continued)

EHPR08-33 Proportional Reducing/Relieving Valve

USASI/ISO:

SYMBOLS

2.970.1

PERFORMANCE



PR

ES

SU

RE

(ps

i)

0

50

100

150

200

250

300

350

400

PR

ES

SU

RE

(ba

r)

0

5

10

15

20

25

30


FLOW (gpm)

FLOW (lpm)

PR

ES

SU

RE

(ba

r)

PR

ES

SU

RE

(ps

i)


0 0.2 0.4 0.6 0.8 1.0

00 0

25

150

100

125

50

75

2

4

6

8

10

1.0 3.02.0 4.0

Cartridge Only

DESCRIPTIONA screw-in, cartridge-style, direct acting, spool-type reducing/relieving valve, whichcan be infinitely adjusted across a prescribed range using a variable electric input.Pressure output is proportional to DC current input. This valve is intended for use as apressure control device in demanding applications.

OPERATIONThe EHPR08-33 allows free flow from ➀ to ➂ when no current is applied to the coil.When the coil is energized, ➁ is connected to ➀. Increasing current applied to the coilwill increase the control (reduced) pressure proportionally. If pressure at ➀ exceedsthe setting induced by the coil, pressure from ➀ is relieved to ➂.


FEATURES• 12 and 24 volt coils standard.• Optional manual override.• Industry common cavity.• Waterproofed coils standard.

RATINGSMaximum Port Pressure: 207 bar (3000 psi)Maximum Control Current: 1.2 amps for 12 VDC coil; 0.6 amps for 24 VDC coil;

For other voltages, consult factoryDither Frequency Required: 200 HzTypical Frequency Response: See Section 10Hysteresis: Less than 3%Reducing/Relieving Pressure Range from Zero to Maximum Control Current:

0–26 bar (0–375 psi)Rated Flow: 4.0 lpm (1.05 gpm), ∆P=6 bar (87 psi), Cartridge only,

➀ to ➂ coil de-energizedStep Response: TON <30 ms; TOFF <12 msFlow Path: Free Flow: ➀ to ➂ coil de-energized; Reduced: ➁ to ➀ coil energized;

Relieving: ➀ to ➂ coil energizedTemperature: -40 to 120°C (-40 to 250°F), with standard Buna N sealsAmbient Air Temperature: -40 to 80°C (-40 to 176°F)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-3; See page 9.108.1; Cavity Tool: CT08-3XX; See page 8.600.1Seal Kit: SK08-3X-00; See page 8.650.1


Typical Relieving/Reducing Pressure vs. Flow CharacteristicTypical Relieving Pressure at Various %’s of Maximum Control Current

Pressure Range “A” (26 bar/375 psi); Cartridge in Body

FLOW (gpm)

% o

f MA

XIM

UM

RE

DU

CIN

G P

RE

SS

UR

E

50

0

25

75

100

125

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

50

0

25

75

100

125

FLOW (lpm)4.0 3.0 2.0 1.0 0 1.0 2.0 3.0 4.0

0 0.20.2 0.40.4 0.60.6 0.80.8 1.01.0Reducing Pressure ➁ to ➀Relieving Pressure ➀ to ➂





PERFORMANCE

EHPR08-33

2.970.2

MATERIALS

Cartridge: Weight: 0.25 kg. (0.55 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. BunaN O-rings.

Standard Ported Body: Weight:0.16 kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); See page8.008.1. Steel and ductile iron bodiesavailable; dimensions may differ;consult factory.

EHPR Series Coil: Weight: 0.11 kg.(0.25 lbs.); Unitized, thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

TO ORDER

EHPR08-33__- __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T

3/8 in. BSP* 3B1/2 in. BSP* 4B*BSP Body;U.K. Mfr. Only


Voltage0 Less Coil

10 *10 VDC (1.5 amps max.)12 12 VDC (1.2 amps max.)20 *20 VDC (0.75 amps max.)24 24 VDC (0.6 amps max.)*For use where there is a voltage drop across the controller.Consult factory for other voltages

2.0652.3

0.164.1

Manual Override Option0.13 (3.3) Hex Socket

(continued)

HYDRAFORCE®



ConnectorsER Deutsch DT04-2P


DIMENSIONS

2 4 6FREQUENCY (Hz)

Typical Frequency Response CurvesInput Current and Regulated Pressure

8 10 20 30 40 50 60

Signal 25% ±10%

Signal 50% ±50%

Signal 85% ±10%

Inlet: 35 bar (500 psi), 4 lpm (1 gpm)Regulated: BlockedTank: <0.15 bar (2 psi)Input Signal: Sinusoidal

-180

-90

-45

0

-135

PH

AS

E (

degr

ees)

9

12

6

3

0

-3

-6

-9

GA

IN (

dB)

Current

0

500

1000

1500

CU

RR

EN

T (

mA

)

0

3.450

6.9100

10.3150

13.8200

17.2250

20.7300

24.2350

27.6400

RE

GU

LAT

ED

PR

ES

SU

RE

(ba

r/ps

i)

TIME (msec.)1006050403020100 20 30 40


Pressure

OptionNone (Blank)

Manual Override M


PWM — 4000144 4000133 4000140


EHPR98-T33 Proportional Reducing/Relieving

USASI/ISO:

SYMBOLS

2.971.1

PERFORMANCE

CURRENT amps

PR

ES

SU

RE

bar

/psi

Reducing Pressure vs. CurrentInlet: 241 bar/3500 psi; 200 Hz PWM


6.9/100

13.8/200

20.7/300

27.6/400

34.5/500

0.2 0.4 0.6 1.00.8 1.41.2

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Pressure Drop vs. FlowBody and Line

➀ to ➂ ———; ➁ to ➀ - - - - -

1.7/25

3.4/50

5.2/75

6.9/100

8.6/125

0.80.2

1.50.4

2.30.6

3.00.8

3.81.0

DESCRIPTIONA direct-acting, spool-type, drop-in-style, flange-mounted, pressure reducing/relievingvalve, which can be infinitely adjusted across a prescribed range using a variableelectric input. Pressure output is proportional to DC current input. The Ecoil is anintegral part of the valve assembly, and cannot be replaced or field-serviced.

OPERATIONThe EHPR98-T33 allows free flow from ➀ to ➂ when no current is applied to the coil.When the coil is energized, ➁ is connected to ➀. Increasing current applied to the coilwill increase the control (reduced) pressure proportionally. If pressure at ➀ exceedsthe setting induced by the coil, pressure from ➀ is relieved to ➂.


FEATURES• Economical drop-in style.• Integral waterproof coil standard.• 10, 12, 20 or 24 VDC coils.• Several push-on termination options.

RATINGSMaximum Inlet Pressure: 241 bar (3500 psi)Common Port Burst Pressure: One cycle at 158 bar (2300 psi) on all ports

simultaneously pressurizedTank Port (➂) Pressure: 34.5 bar (500 psi) maximum for 100,000 cyclesMaximum Control Current: 1.38 amps for 10 VDC coil; 1.30 amps for 12 VDC coil;

0.69 amps for 20 VDC coil; 0.65 amps for 24 VDC coil;Hysteresis: Less than 3% with 200 Hz PWMRated Flow: 3.8 lpm (1.0 gpm), cartridge only, ➀ to ➂ coil de-energizedStep Response: TON <30 ms; TOFF <12 msTemperature: -40 to 120°C (-40 to 250°F), with standard Buna N sealsAmbient Air Temperature: -40 to 80°C (-40 to 176°F)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 ssu)Installation: Flange MountMounting Screws: M4 x 0.7 x 10 Long; Part No. 4001015Cavity and Cavity Tool: VC-T009; See page 9.108.1Seal Kit: SK98-T39X-000; See page 8.650.1


Relieving Pressure ➀ to ➂

Typical Relieving/Reducing Pressure vs. Flow CharacteristicTypical Relieving Pressure at Various %s of Maximum Control Current

Inlet: 241 bar/3500 psi; 100 Hz PWM (Both Directions)

FLOW lpm/gpm

3.81.00

2.80.75

1.90.50

0.90.25

0 0.90.25

1.90.50

2.80.75

3.81.00


100% Max. Control Current75% Max. Control Current50% Max. Control Current25% Max. Control Current0% Max. Control Current

% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

% o

f MA

XIM

UM

RE

DU

CIN

G P

RE

SS

UR

E

50

0

25

75

100

125

50

0

25

75

100

125

PERFORMANCE

EHPR98-T33

2.971.2

1.0927.6

1.7343.9

2.1354.1

1.3133.3

INCHMILLIMETRE

2.1554.6

1.1228.4

MountingScrew

Torque:0.9–1.1 ft-lbs(1.2–1.5 Nm)

0.184.6

40°

(continued)

HYDRAFORCE®

DIMENSIONS

0.1FREQUENCY Hz

Typical Frequency Response CurvesInlet: 241 bar/3500 psi; Regulated Port Blocked

Signals: 40% ±10% ———; 50% ±25% — — —; 70% ±20% - - - - - -

1.0 10.0 50.0

180

90

45

0

135

PH

AS

E A

NG

E d

egre

es

6

7

45

8

3

-4

-3

-2

-1

0

1

2

-5

-6

-7

-8

MA

GN

ITU

DE

dB

0

6.9/100

13.8/200

20.7/300

27.6/400

34.5/500

41.4/600

PR

ES

SU

RE

(ba

r/ps

i)

TIME seconds0.450.400.350.300.250.15 0.200.100.050 0.50

Typical Step Response CurveInlet 241 bar/3500 psi; Regulated Port Blocked

Pressure

CurrentInput Sig.w/12V or DIN Coil PCB Metal DIN Rail24V Coil Mount Board Box Mount0-5 VDC 4000161 4000194 4000174 40001360-10 VDC 4000165 4000141 4000182 40001374-20 mA 4000169 4000143 4000186 4000139

PWM — 4000144 4000133 4000140


Drop-In-Style Valve

OptionNone (Blank)

233µ screen S on inlet port

MATERIALS

Cartridge including Coil: Weight:0.20 kg. (0.44 lbs.); Steel withhardened work surfaces. Zinc-Nickel plated exposed surfaces;HNBR O-rings standard. Coil isencapsulated, class H high-temperature magnetwire, withzinc-nickel plated shell.

Ported Body: Consult Factory

EHPR98-T33 __ - __ __ - __ - __ __ __ __TO ORDER

Voltage10 10 VDC12 12 VDC20 20 VDC24 24 VDC

TerminationER Deutsch DT04-2PEJ Amp Junior Timer

PortingConsult Factory

Other voltages andcoils with internaldiode are available.Consult factory.

SealsHydrogenated Nitrile N

(HNBR)


USASI/ISO:

SYMBOLS

2.972.1

PERFORMANCE

CURRENT amps

PR

ES

SU

RE

bar

/psi

Reducing Pressure vs. CurrentInlet: 25 bar/365 psi; 100 Hz PWM

Reduced Pressure to

2.8/405.5/80

8.3/12011.0/16013.8/20016.5/24019.3/28022.1/320

0.2 0.4 0.6 1.00.8 1.41.2

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Pressure Drop vs. FlowCartridge Only

1 to 3 —— ; 2 to 1 - - - -

1.7/25

3.4/50

5.2/75

6.9/100

8.6/125

10.3/150

12.1/175

0.90.25

1.90.50

2.80.75

3.81.00

4.71.25

5.71.50

DESCRIPTIONA direct-acting, spool-type, drop-in-style, fl ange-mounted, pressure reducing/reliev-ing valve, which can be infi nitely adjusted across a prescribed range using a variable electric input. Pressure output is proportional to DC current input. The Ecoil is an integral part of the valve assembly, and cannot be replaced or fi eld-serviced.

OPERATIONThe EHPR98-T35 allows free fl ow from ➀ to ➂ when no current is applied to the coil. When the coil is energized, ➁ is connected to ➀. Increasing current applied to the coil will increase the control (reduced) pressure proportionally. If pressure at ➀ exceeds the setting induced by the coil, pressure from ➀ is relieved to ➂.Note: Back pressure on port ➂ becomes additive to the pressure setting at a 1:1 ratio.

FEATURES• Economical drop-in style. • Several push-on termination options.• Integral waterproof coil standard. • 1000-hour salt spray protection.• 10, 12, 20 or 24 VDC coils.

RATINGSMaximum Inlet Pressure: 103 bar (1500 psi); If higher inlet pressure is required

(103 bar/1500 psi to 241 bar/3500 psi) select the “A” option in the model code.Maximum Tank Pressure: 34.5 bar (500 psi);

with Manual Override Option: 17.2 bar (250 psi)Control Pressure at Maximum Control Current: 20.7 bar (300 psi)Maximum Control Current: 1.38 amps for 10 VDC coil; 1.30 amps for 12 VDC coil;

0.69 amps for 20 VDC coil; 0.65 amps for 24 VDC coilResistance: 4.2Ω (10V); 5.1Ω (12V); 17.0Ω (20V); 19.3Ω (24V)Inductance: 80 mH (12V); Hysteresis: Less than 4% with 100 Hz PWMFlow Rating: 5.7 lpm (1.5 gpm)Maximum Internal Leakage:

De-energized: 75 ml/minute (4.58 cu. in./minute) at 25 bar (365 psi); 200 ml/minute (12.2 cu. in minute) at 241 bar (3500 psi).Energized at I-Max.: 125 ml/minute (7.63 cu. in./minute) at 25 bar (365 psi); 400 ml/minute (24.4 cu. in. minute) at 241 bar (3500 psi)

Temperature: -40 to 120°C (-40 to 250°F), with standard Buna N sealsAmbient Air Temperature: -40 to 80°C (-40 to 176°F)Environmental Rating: IP69KFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: Flange MountMounting Screws: M4 x 0.7 x 12 Long; Part No. 4001015 (not provided with valve)Cavity: VC-T009; See page 9.111.1; Cavity Tool: CT-T009R0-x-G; See page 8.600.1Seal Kit: SKEHPR98-T3X; See page 8.650.1



Typical Relieving/Reducing Pressure vs. Flow CharacteristicInlet: 25 bar/365 psi ——— ; Inlet: 241 bar/3500 psi - - - - -

100 Hz PWM (Both Directions); Note: Curves overlap on Relieving Pressure (LH) side of graph

FLOW lpm/gpm

3.81.00

4.71.25

5.71.50

2.80.75

1.90.50

0.90.25

0 0.90.25

1.90.50

2.80.75

3.81.00

4.71.25

5.71.50


0 mA

RE

LIE

F P

RE

SS

UR

E b

ar/p

si

RE

DU

CIN

G P

RE

SS

UR

E b

ar/p

si

6.9/100

0

3.4/50

10.3/150

24.1/350

27.6/400

0

20.7/300

17.2/250

13.8/200

6.9/100

3.4/50

10.3/150

24.1/350

27.6/400

20.7/300

17.2/250

13.8/200

1300 mA

1000 mA

800 mA

600 mA400 mA

HYDRAFORCE.com®

RP



PERFORMANCE

EHPR98-T35

2.972.2

(continued) DIMENSIONS

0.1FREQUENCY Hz

Typical Frequency Response CurvesInlet: 25 bar/365 psi; DC Current; Regulated Port Blocked

Signals: 40% ±10% ——; 50% ±25% — —; 70% ±20% – – –; 80% ±10% - - - -

1.0 10.0 50.0

180

90

45

0

135

PH

AS

E A

NG

E d

egre

es

6

7

45

8

3

-4

-3

-2

-1

0

1

2

-5

-6

-7

-8

MA

GN

ITU

DE

dB

0

3.4/50

6.9/100

10.3/150

13.8/200

17.2/250

20.7/300

24.1/350

PR

ES

SU

RE

bar

/psi

TIME seconds0.50 1.00 1.50 2.00 2.50 3.000

Typical Step Response CurveInlet 25 bar/365 psi; Regulated Port Blocked

Pressure

DC Current

Drop-In-Style Valve

MATERIALS

Cartridge including Coil: Weight: 0.20 kg. (0.44 lbs.) Steel with hardened work surfaces. Zinc-Nickel plated exposed surfaces. HNBR O-rings standard. Coil is encapsulated, class H high-temperature magnetwire, with zinc-nickel plated shell.

Ported Test Body: Consult Factory

Mounting Screws: Must be ordered separately: Part No. 4001015

EHPR98-T35 __ __ __- __ __ - __ - __ __ __ __ __TO ORDER

Voltage 10 10 VDC 12 12 VDC 20 20 VDC 24 24 VDC


Seals N Hydrogenated Nitrile (HNBR) V Fluorocarbon

Other voltages are available. Consult factory.

®HYDRAFORCE

HYDRAFORCE.com®

Porting Cartridge Only 0

Option None (Blank)

Manual Override M

Inlet Pressure 0 to 103 bar (0 to 1500 psi) (Blank)

103 to 241 bar (1500 to 3500 psi) A

1.0927.6

1.7343.9

2.1354.1

1.3133.3

INCHMILLIMETRE

2.1554.6

0.4711.9

1.1228.4

MountingScrewTorque:

0.9–1.1 ft-lbs(1.2–1.5 Nm)


0.256.4

40°

ScreenOption


Note: For additional Frequency Response or Step Response information, consult factory.

Screen Option None (Blank)

142µ on Inlet Port 2 S

Diode (Blank) None Z Zener Diode, Bidirectional

RP




USASI/ISO:

SYMBOLS

2.973.1

PERFORMANCE

DESCRIPTIONA direct-acting, spool-type, drop-in-style, fl ange-mounted, pressure reducing/reliev-ing valve, which can be infi nitely adjusted across a prescribed range using a variable electric input. Pressure output is proportional to DC current input. The Ecoil is an integral part of the valve assembly, and cannot be replaced or fi eld-serviced.

OPERATIONThe EHPR98-T38 allows free fl ow from ➀ to ➂ when no current is applied to the coil. When the coil is energized, ➁ is connected to ➀. Increasing current applied to the coil will increase the control (reduced) pressure proportionally. If pressure at ➀ exceeds the setting induced by the coil, pressure from ➀ is relieved to ➂.Note: Back pressure on port ➂ becomes additive to the pressure setting at a 1:1 ratio.

FEATURES• Economical drop-in style. • 1000-hour salt spray protection.• Integral waterproof coil standard. • 10, 12, 20 or 24 VDC coils.

RATINGSMaximum Inlet Pressure: 241 bar (3500 psi)Tank Port (➂) Pressure: 34.5 bar (500 psi) maximum;

17.2 bar (250 psi) maximum with manual override option.Maximum Control Current: 1.38 amps for 10 VDC coil; 1.30 amps for 12 VDC coil;

0.69 amps for 20 VDC coil; 0.65 amps for 24 VDC coil;Control Pressure at Maximum Control Current: 30 bar (435 psi)Resistance: 4.3 ohm (10V); 5.2 ohm (12V); 17.5 ohm (20V); 20.9 ohm (24V)Inductance: 80 mH (12V)Hysteresis: at 150 Hz PWM: 5% of maximum control pressureFlow Rating: 18.9 lpm (5.0 gpm)Maximum Internal Leakage: De-engergized: 50 ml/min. (3 cu. in./min.) at 34.5 bar

(500 psi); Energized at I-max: 100 ml/min. (6 cu. in./min.) at 34.5 bar (500 psi)Temperature: -40 to 120°C (-40 to 250°F), with standard Buna N sealsAmbient Air Temperature: -40 to 80°C (-40 to 176°F)Environmental Rating: IP69KFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Mounting Screws: M4 x 0.7 x 12 Long; Part No. 4001015 (not provided with valve)Cavity: VC-T011; See page 9.111.1Cavity Tool: CT-T011R0-x-G; See page 8.600.1Seal Kit: SK-T011; See page 8.650.1


HYDRAFORCE.com®

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Pressure Drop vs. FlowCartridge Only

to ———; to - - - - -

1.7/25

3.4/50

5.2/75

6.9/100

8.6/125

3.81.0

7.62.0

11.43.0

15.14.0

18.95.0


Typical Relieving/Reducing Pressure vs. Flow CharacteristicTypical Relieving Pressure at Various %s of Maximum Control Current

Inlet: 34.5 bar/500 psi ——; Inlet 241 bar/3500 psi – – –(Curves overlap on Relieving Pressure side of graph); 150 Hz PWM (Both Directions)

FLOW lpm/gpm

15.14.0

15.14.0

18.95.0

18.95.0

11.43.0

11.43.0

7.62.0

7.62.0

3.81.0

3.81.0

0


100% Max. Control Current75% Max. Control Current

30% Max. Control Current0% Max. Control Current


% o

f MA

XIM

UM

RE

LIE

F P

RE

SS

UR

E

% o

f MA

XIM

UM

RE

DU

CIN

G P

RE

SS

UR

E

50

0

25

75

100

125

150

50

25

75

100

125

150

0


CURRENT amps

PR

ES

SU

RE

bar

/psi

Reducing Pressure vs. Current

6.9/100

13.8/200

20.7/300

27.6/400

34.5/500

0.2 0.4 0.6 1.00.8 1.41.2

Reducing Pressure ➁ to ➀Inlet: 34.5 bar/500 psi; 150 Hz PWM; 12V Coil

RP



PERFORMANCE

EHPR98-T38

2.973.2

(continued) DIMENSIONS

Drop-In-Style Valve

MATERIALS

Cartridge including Coil: Weight: 0.32 kg. (0.70 lbs.) Steel with hardened work surfaces. Zinc-Nickel plated exposed surfaces. HNBR O-rings standard. Coil is encapsulated, class H high-temperature magnetwire, with zinc-nickel plated shell.

Ported Test Body: Consult FactoryMounting Screws: Must be ordered

separately: Part No. 4001015

EHPR98-T38 __ - __ __ - __ - __ __ __ __ __TO ORDER

Voltage 10 10 VDC 12 12 VDC 20 20 VDC 24 24 VDC


®HYDRAFORCE

HYDRAFORCE.com®


Option None (Blank)

Manual Override M


0

6.9/100

13.8/200

20.7/300

27.6/400

34.5/500

PR

ES

SU

RE

(ba

r/ps

i)

TIME seconds2.252.001.751.501.250.75 1.000.500.250 2.50

Typical Step Response CurveInlet 34.5 bar/500 psi; DC Current; Regulated Port Blocked

Pressure

Current (amps x 100)

1.0627.0

1.7343.9

2.1354.1

1.3133.3

INCHMILLIMETRE

2.1554.6

0.4711.9

1.6642.1

MountingScrewTorque:

0.9–1.1 ft-lbs(1.2–1.5 Nm)


0.256.4

40

Note: To operate manual override, rotate screw clockwise until desired pressure is achieved.

FREQUENCY Hz

Typical Frequency Response CurvesInlet: 34.5 bar/500 psi; DC Current; Regulated Port Blocked

(For 241 bar/3500 psi inlet frequency response curves, consult factory.)

Signals: 40% ±10% ———; 50% ±25% — — —70% ±20% - - - - - -; 80% ±10% — - — - —

1 10 50

180

90

45

0

135

PH

AS

E A

NG

E d

egre

es

8

10

4

6

12

2

-4

-2

0

-6

-8

-10

-12

MA

GN

ITU

DE

dB

Seals Hydrogenated Nitrile (HNBR) N Fluorocarbon V

Diode (Blank) None Z Zener Diode, Bidirectional

Other voltages are available. Consult factory.

RP



HSP16-20 HyPerformanceTM Poppet, 2-Way, N.C.

DESCRIPTIONA proportional solenoid-operated, 2-way, poppet-type, normally closed, screw-in hydraulic cartridge valve for low-leakage blocking and load-holding in high pressure applications requiring low internal leakage.

OPERATIONWhen de-energized, the HSP16-20 acts as a check valve, allowing fl ow from ➀ to ➁, and blocking fl ow from ➁ to ➀. When energized, the ➁ to ➀ fl ow path opens. Flow is proportional to current applied to the coil.Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the use of 10 volt or 20 volt coils respectively. See “SP Valves and Coil Operating Parameters,” page 2.002.1.

FEATURES• Industry-common cavity. • Effi cient wet-armature construction.• Continuous-duty rated coils. • Waterproof E-Coils rated up to IP69K.• 1000-hour salt-spray rated solenoid tubes.• All HyPerformance products are tested to NFPA specifi cation T2.6.1,

and are tested at a verifi cation level of 90% and an assurance of 99%.

RATINGSOperating Pressure: 350 bar (5075 psi); 10% Cycle Life: 420 bar (6090 psi)Fatigue Rating: 2 million cycles at 420 barBurst Pressure: 1380 bar (20,000 psi)Flow: Up to 265 lpm (70 gpm); see performance curves.Hysteresis: From 3.8 to 11.3 lpm (1 to 3 gpm): Less than 7.6 lpm (2 gpm);

From 11.3 to 113.4 lpm (3 to 30 gpm): Less than 15.1 lpm (4 gpm);Maximum Control Current: 1.2 ampsMax. Internal Leakage: 7 drops per minute at 345 bar (5000 psi) inletTemperature: -54° to 107°C (-65° to 225°F) with Urethane sealsFluids: Mineral-based or synthetics with lubricating properties at viscosities

of 7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Filtration: See page 9.010.1; Installation: No Restrictions. See page 9.020.1Cavity: HVC16-2; See page 9.116.1; Cavity Tool: HCT16-2XX; See page 8.600.1Seal Kit: SK16-2U-O; See page 8.650.1; Coil Nut: Part No. 4553800


SYMBOLSUSASI/ISO:

2.016.1

PERFORMANCE

HYDRAFORCE.com®


FLO

W lp

m/g

pm

227/60

246/65

189/50

208/55

151/40

170/45

114/30

133/35

76/20

95/25

38/10

19/5

57/15

0

FLOW vs. CURRENT at Various Inlet Pressureswith 12 VDC Coil — 32 cSt/150 sus oil at 40°C

PERCENT of MAX. CONTROL CURRENT10 20 30 40 50 60 70 80 90 100

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 AMP

345 bar5000 psi

35 bar500 psi

104 bar1500 psi

11 bar160 psi

5.5 bar80 psi

3810

7620

11330

15140

18950

22760

26570

FLOW lpm/gpm

35/500

69/1000

103/1500

138/2000

172/2500

207/3000

PR

ES

SU

RE

bar

/psi

TYPICAL PRESSURE RESPONSE

0.75A 0.85A 0.90A

0.95A

1.00A

1.20A1 to 2 De-En

RP



HSP16-20

2.016.2

DIMENSIONS

MATERIALS TO ORDER

HSP16-20 __ - __ __ __ - __ - __ __ __ __ __

Recommended for pressures above 241 bar (3500 psi).


Seals PPDI Urethane U

Option None (Blank)

®HYDRAFORCE

HYDRAFORCE.com®

Cartridge: Weight: 0.32 kg. (0.71 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Urethane O-rings with no back-up standard.

Ported Body: Ductile iron recommended for pressures above 207 bar (3000 psi). Consult Factory.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. See page 3.400.1.

Voltage 0 Less Coil** 10 10 VDC (D- or E-Coil) 12 12 VDC (D- or E-Coil) 20 20 VDC (E-Coil) 24 24 VDC (D- or E-Coil)

For Coils with Zener Diode, add “/Z” to option code. For example: “ER/Z”. Not available on all models. See coil option info. on page 3.400.1

Coil TerminationDeutsch DT04-2P ER (IP69K)Metri-Pak 150 EY (IP69K)Dual Lead Wires EL (IP69K)Amp Jr. Timer EJ (IP67)DIN 43650 EG (IP65)

**Includes E-Coil Nut.

1.6241.1

1.84


DIA.46.7

2.54

ORIFICE DISC CANNOTBE USED WITH THIS PRODUCTdue to HyPerformanceTM Cavity.

64.5

1.56ACROSS FLATS

39.81.84

TORQUE: 5 – 7 ft-lb.6.8 – 9.5 Nm

TORQUE:195 – 205 ft-lb.265 – 278 Nm

46.7

RP



YDRAFORCE Electro-Proportional Valves · 2.000.1 ®HYDRAFORCE Electro-Proportional Valves •...

Documents

Transcript of YDRAFORCE Electro-Proportional Valves · 2.000.1 ®HYDRAFORCE Electro-Proportional Valves •...