MANUAL NO. SIEP C710606 31A

Technical Manual

YASKAWA AC Drive-J1000

Type: CIMR-JU

Compact V/f Control Drive

Models: 200 V Class, Three-Phase Input: 0.1 to 5.5 kW200 V Class, Single-Phase Input: 0.1 to 2.2 kW400 V Class, Three-Phase Input: 0.2 to 5.5 kW

To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user receives this manual.

3

2

1

4

5

6

7

8

A

B

C

D

Receiving

Mechanical Installation

Electrical Installation

Parameter Details

Troubleshooting

Specifications

Parameter List

Standards Compliance

Start-Up Programming & Operation

Periodic Inspection &Maintenance

Peripheral Devices &Options

MEMOBUS/ModbusCommunications

This Page Intentionally Blank

2 YASKAWA ELECTRIC SIEP C710606 31A YASKAWA AC Drive J1000 Technical Manual

Copyright 2008 YASKAWA ELECTRIC CORPORATION. All rights reserved.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, inany form or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior writtenpermission of Yaskawa. No patent liability is assumed with respect to the use of the information contained herein.Moreover, because Yaskawa is constantly striving to improve its high-quality products, the information containedin this manual is subject to change without notice. Every precaution has been taken in the preparation of thismanual. Yaskawa assumes no responsibility for errors or omissions. Neither is any liability assumed for damagesresulting from the use of the information contained in this publication.

Table of Contentsi. PREFACE & GENERAL SAFETY.................................................................... 9

i.1 Preface ....................................................................................................................... 10Applicable Documentation....................................................................................................... 10Symbols................................................................................................................................... 10Terms and Abbreviations ........................................................................................................ 10

i.2 General Safety ........................................................................................................... 11Supplemental Safety Information ............................................................................................ 11Safety Messages..................................................................................................................... 11Drive Label Warnings .............................................................................................................. 13Warranty Information............................................................................................................... 14Quick Reference...................................................................................................................... 14

1. RECEIVING .................................................................................................... 151.1 Section Safety............................................................................................................ 161.2 Model Number and Nameplate Check ..................................................................... 17

Nameplate ............................................................................................................................... 171.3 Component Names.................................................................................................... 19

IP20/Open-Chassis ................................................................................................................. 19Front Views ............................................................................................................................. 21

2. MECHANICAL INSTALLATION..................................................................... 232.1 Section Safety............................................................................................................ 242.2 Mechanical Installation ............................................................................................. 26

Installation Environment .......................................................................................................... 26Installation Orientation and Spacing........................................................................................ 27Exterior and Mounting Dimensions ......................................................................................... 28

3. ELECTRICAL INSTALLATION ...................................................................... 313.1 Section Safety............................................................................................................ 323.2 Standard Connection Diagram................................................................................. 343.3 Main Circuit Connection Diagram............................................................................ 36

Single-Phase 200 V Class (CIMR-JoBA0001 ~ 0010)........................................................... 36Three-Phase 200 V Class (CIMR-Jo2A0001 ~0020);Three-Phase 400 V Class (CIMR-Jo4A0001 ~ 0011)........................................................... 36

3.4 Terminal Block Configuration .................................................................................. 373.5 Protective Covers...................................................................................................... 38

YASKAWA ELECTRIC SIEP C710606 31A YASKAWA AC Drive J1000 Technical Manual 3

IP20/Open-Chassis Cover Removal and Installation ........................................................................ 383.6 Main Circuit Wiring..............................................................................................................39

Main Circuit Terminal Functions........................................................................................................ 39Wire Gauges and Tightening Torque ................................................................................................ 39Main Circuit Terminal Power Supply and Motor Wiring..................................................................... 40

3.7 Control Circuit Wiring .........................................................................................................42Control Circuit Terminal Block Functions .......................................................................................... 42Terminal Configuration ...................................................................................................................... 43Wiring Procedure............................................................................................................................... 44

3.8 I/O Connections...................................................................................................................46Sinking/Sourcing Mode Switch.......................................................................................................... 46

3.9 Main Frequency Reference.................................................................................................48DIP Switch S1 Analog Input Signal Selection ................................................................................... 48

3.10 Braking Resistor..................................................................................................................49Installation ......................................................................................................................................... 49

3.11 Interlocking with Connected Machinery ...........................................................................51Drive Ready Signal............................................................................................................................ 51

3.12 Wiring Checklist ..................................................................................................................524. START-UP PROGRAMMING & OPERATION ...................................................... 53

4.1 Section Safety......................................................................................................................544.2 Using the Digital LED Operator..........................................................................................56

Keys, Displays, and LEDs ................................................................................................................. 56Digital Text Display............................................................................................................................ 57LED Screen Displays ........................................................................................................................ 57LO/RE LED and RUN LED Indications.............................................................................................. 57Menu Structure for Digital LED Operator .......................................................................................... 58

4.3 The Drive and Programming Modes..................................................................................59Navigating the Drive and Programming Modes................................................................................. 59Changing Parameter Settings or Values ..........................................................................