XTR115 + TPS54062
-
Upload
athena-snyder -
Category
Documents
-
view
21 -
download
0
description
Transcript of XTR115 + TPS54062
![Page 1: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/1.jpg)
XTR115 + TPS54062Objective: Increase the available power for sensor and other external circuitry on a remote 2-wire current loop transmitter.
With existing designs, sensors and systems that draw more than ~3.3mA will not be able to meet typical under-scale current or zero-scale levels of 3.8mA or 4mA.
Loop Supply – 16VDesired Iout range = 3.8mA DC – 20.2mA DC with 1mApp HART AC signalRequired Sensor Current = 7.1mA
![Page 2: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/2.jpg)
XTR115 + TPS54062
Vreg
Vref
Iin
Iret
V+
B
E
Iout
Loop Supply
(24VDC)
20k
TPS54062EVM
Iout_TPS = 9mA
Iret = 2.75mA
Iout_XTR
XTR115
Vout (5VDC) Vin
GND
250R
+
-
Sensor
V+
V-
Out
4-20mA
Solution: Use low-current buck topology switching power converter to buck down the loop-supply to the required VREG levels. All SMPS current must sink back through IRET of XTR115.
EfficiencyPout
Pin
Vout Iout_TPS
VLoop IRETIout_TPS
Efficiency IRET VLoop
Vout
![Page 3: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/3.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 1uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
At 2.2kHz, Max IRET increased to 2.6mA before signal degradation occurred
TPS_IOUT = 7.2mA
IRET = 2.6mA
![Page 4: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/4.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 1uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
Showing the +3.3V output with the reduced 1uF capacitance, output looks good
DC Couple AC Couple
![Page 5: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/5.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 0.47uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
At 2.2kHz, Max IRET increased to 2.85mA before signal degradation occurred
IRET = 2.8mA
TPS_IOUT = 9mA
![Page 6: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/6.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 0.47uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
At 2.2kHz, Max IRET increased to 2.85mA before signal degradation occurred
IRET = 2.85mA
TPS_IOUT = 9.25mA
![Page 7: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/7.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 0.47uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
At 2.2kHz, Showing distortion with IRET = 2.9mA
IRET = 2.9mA
TPS_IOUT = 9.5mA
![Page 8: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/8.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 0.47uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
At 2.2kHz, Showing distortion with IRET = 3mA
IRET = 3mA
TPS_IOUT = 10mA
![Page 9: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/9.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 0.47uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
Showing the +3.3V output with the reduced 0.47uF capacitance, output looks good
DC Couple AC Couple
![Page 10: XTR115 + TPS54062](https://reader036.fdocuments.in/reader036/viewer/2022072114/5681334f550346895d9a584b/html5/thumbnails/10.jpg)
XTR115 + TPS54062Setup:
XTR115 + TPS54062EVM with reduced input capacitance of 0.47uF
Output: 3.8mA DC + 1mAPP 2.2kHz HART signal
Results:
Showing the +16V input ripple with the reduced 0.47uF capacitance, looks similar when compared to original
2.2uF Input cap 0.47uF Input Cap