XLR-8 EXTENDED RACK - Teledyne Cetac EXTENDED RACK ACCESSORIES AND PARTS CATALOG Catalog part number...
Transcript of XLR-8 EXTENDED RACK - Teledyne Cetac EXTENDED RACK ACCESSORIES AND PARTS CATALOG Catalog part number...
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
2
Accessories and SuppliesTray XLR-8 SP7025
Z-Axis Drive Assembly PEEK Anti Kink
For use with Carbon Fiber and Ultem Probes
(PEEK Drive Cable-Green)
*Guide plate included for use with probes other than Carbon Fiber versions, typically Ultem
SP7171
Z-Axis Drive Tubing Replacement Kit (PEEK Anti-Kink)
SP7174
Sample ProbesLength: 10 inches (25.4 cm)Probe Material: FEP-covered carbon fiberCapillary Material: PFA
ID (mm) Band Capillary Length Part Number0.3 Black 108 in (2.74 m) SP5799C0.5 Blue 108 in (2.74 m) SP5800C0.8 Red 108 in (2.74 m) SP5796C0.9 Yellow 70 in (1.78 m) SP5950C1.0 2 Blue 108 in (2.74 m) SP6013CSample Racks
90 Position, 13.3 mm Round opening, used with 8mL round bottom or 7mL flat bottom vial
90 Position, 13.5 mm Square opening, used with 8mL round bottom or 7mL flat bottom vial
450362
450055
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
3
60 Position, 17.0 mm Square opening, used with 14mL or 15mL vial
40 Position, 20.6 mm Square opening, used with 20mL vial
24 Position, 25.2 mm Square opening, used with 30mL vial
21 Position, 30.5 mm Square opening, used with 50mL vial
450056
450057
450058
450059
Vials
7mL, 13mm x 82mm (1000/kit)7mL, 13mm x 82mm (250/kit)(Flat bottom with cap)
8mL, 13mm x 100mm (1000/kit)8mL, 13mm x 100mm (250/kit)(Round bottom without cap)
14mL, 16mm x 100mm (1000/kit)14mL, 16mm x 100mm (250/kit)
15mL, 17mm x 100mm (1000/kit)15mL, 17mm x 100mm (250/kit)
20mL, 21.5mm x 100mm (500/kit)20mL, 21.5mm x 100mm (100/kit)
30mL, 25mm x 95mm (500/kit)
50mL, 30mm x 115mm (500/kit)50mL, 30mm x 115mm (100/kit)
Material for all vials is polypropylene
SP5178ASP5178E
SP5178KSP5178L
SP5178BSP5178F
SP5178MSP5178N
SP5178GSP5178I
SP5178H
SP5178CSP5178J
Z-Drive Attachment Kit SP5903
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
4
Thumbscrew and O-ring Kit SP5919
Y-Axis Slider Block (Home Block) Hardware Kit SP5918
Drain Pump Tubing and Connector Kit (PharMed)
SP6089
Drain Pump Tubing and Connector Kit (Tygon) SP6090
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
5
Repair Parts
Rotor Assembly SP6346
Rinse Station SP5337
Rinse Station Block SP5340
X-Axis Drive Belt SP5222
Pump Motor Kit
2-Channel
SP7002A
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
6
Carriage – Stepper Ribbon Cable-31” (For use with Two-Piece Shield and Splashguard Kit)
SP6378
Two-Piece Shield and Splashguard Kit SP6377
Switch / Power Input (6 pin input)SP6104
Power Cable – XLR-8 Base to Autosampler Head SP6979
24-Volt Power Supply (Standard ASX-520)
28-Volt Power Supply (Standard ASX-520HS)
SP6103
SP7020
Power Cords
US VersionEuro VersionUK VersionAustralian Version
SP5003SP5004SP5005SP6772
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
7
CPU Board (Rabbit)
XLR-8 Standard Version
XLR-8 HS Version
SP6143-23
SP6144-24
Main Board (for XLR-8 Base) SP6978
Main Board (Conformal Coated) SP6111
X-Axis Sensor SP6107
Sensor wiring harness, XLR-8 SP6989
Electrical Backpanel Assembly-Main Board not included
SP6990
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
8
Full Drive Motion Assembly (including motor, leadscrew, sensors)
SP6986
Chain with bracket SP6982
Standard Height Autosampler Mounting Block SP6984
150mm Extended Height Autosampler Mounting Block (for sample tubes that are 150mm in height)
SP6985
Guide Rail Set, XLR-8 SP6987
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
9
Transport Cart Assembly, XLR-8 SP6983
RS232 Cable, Female/Female, 15 ft, Black
*Connects the autosampler to the computer
SP6981
RS232 Cable, Female/Female, 3 ft, Black
*Connects the head to the base
SP6980
Accessory Cart – Polypropylene 24-in x 36-in
(for holding the XLR-8)
SP7107
Z-Axis Stepper Motor SP6108
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
10
X-Axis Stepper Motor SP6109
Y-Axis Stepper Motor SP6110
Y-Axis Sensor SP6106
Z-Axis Sensor SP6105
Arm Tube Assembly
CETAC White
SP6202
Y-Axis Lead Screw Kit SP5335
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
11
X-Axis Lead Screw Kit SP5940
Guide Shaft SP5221
Bearing, 7/8" x 3/8" SP6239
Bearing ½" ID (Set of 2) SP7999
Front Cover with Rinse Station
CETAC White color
SP6201
10 Position standards rack, XLR-8 SP6988
XLR-8 AUTOSAMPLER ACCESSORIES AND PARTS
12
OrderingTo order, contact:
Phone (Toll-Fee, USA): 800-369-2822Phone (Outside USA): +1-402-733-2829Fax: +1-402-733-5292e-mail: [email protected]
Teledyne CETAC Technologies14306 Industrial RoadOmaha, Nebraska 68144, USA
For questions about service and repair, call us at the numbers above or e-mail [email protected]
Trademark Acknowledgements: PharMed and Tygon are registered trademarks of Saint-Gobain Performance Plastics. Viton® is a registered trademarks of E.I. du Pont de Nemours and Company. Superthane is a registered trademark of NewAge Industries, Inc.