X9 500 Evo Workshop Manual
-
Upload
viktor-kadek -
Category
Documents
-
view
236 -
download
0
Transcript of X9 500 Evo Workshop Manual
-
8/6/2019 X9 500 Evo Workshop Manual
1/434
WORKSHOP MANUAL
633234
X9 Evolution 500
-
8/6/2019 X9 500 Evo Workshop Manual
2/434
WORKSHOPMANUAL
X9 Evolution 500
The descriptions and illustrations given in this publication are not binding. While the basic specificationsas described and illustrated in this manual remain unchanged, PIAGGIO-GILERA reserves the right, at
any time and without being required to update this publication beforehand, to make any changes tocomponents, parts or accessories, which it considers necessary to improve the product or which are
required for manufacturing or construction reasons.Not all versions shown in this publication are available in all countries. The availability of single versions
should be checked at the official Piaggio sales network." Copyright 2005 - PIAGGIO & C. S.p.A. Pontedera. All rights reserved. Reproduction of this publication
in whole or in part is prohibited."PIAGGIO & C. S.p.A. - Q.C.S./After sales V.le Rinaldo Piaggio, 23 - 56025 PONTEDERA (Pi)
www.piaggio.com
-
8/6/2019 X9 500 Evo Workshop Manual
3/434
-
8/6/2019 X9 500 Evo Workshop Manual
4/434
-
8/6/2019 X9 500 Evo Workshop Manual
5/434
INDEX OF TOPICS
CHARACTERISTICS CHAR
TOOLING TOOL
MAINTENANCE MAIN
TROUBLESHOOTING TROUBL
ELECTRICALSYSTEM ELE SYS
ENGINEFROMVEHICLE ENG VE
ENGINE ENG
INJECTION INJEC
SUSPENSIONS SUSP
BRAKINGSYSTEM BRAK SYS
COOLINGSYSTEM COOL SYS
CHASSIS CHAS
PRE-DELIVERY PRE DE
TIME TIME
-
8/6/2019 X9 500 Evo Workshop Manual
6/434
INDEX OF TOPICS
CHARACTERISTICS CHAR
-
8/6/2019 X9 500 Evo Workshop Manual
7/434
This section describes the general specifications of the vehicle.
Rules
This section describes general safety rules for any maintenance operations performed on the vehicle.
Safety rules
Should it be necessary to keep the engine running while servicing, make sure that the area
or room is well ventilated, and use special exhaust fans, if required. never let the engine run
in an enclosed area. Exhaust fumes are toxic.
The battery electrolyte contains sulphuric acid. Protect your eyes, clothes and skin. Sul-
phuric acid is highly corrosive; in the event of contact with your eyes or skin, rinse thoroughlywith abundant water and seek immediate medical attention.
The battery produces hydrogen, a gas that can be highly explosive. Do not smoke and avoid
sparks or flames near the battery, especially when charging it.
Fuel is highly flammable, and in some conditions it can be explosive. Do not smoke in the
working area, and avoid open flames or sparks.
Clean the brake pads in a well ventilated environment, directing the compressed air jet so
as to not inhale the dust produced by the wear of the friction material. Even though the latter
contains no asbestos, dust inhalation is harmful.
Maintenance rules
Use original PIAGGIO spare parts and lubricants recommended by the Manufacturer. Non-
original or non-conforming spares may damage the vehicle.
Use only the special tools designed for this scooter.
Always use new gaskets, sealing rings and split pins upon reassembly.
After removal, clean the components using non-flammable or low fire-point solvent. Lubri-
cate all the work surfaces except the tapered couplings before refitting. After reassembly, check that all components have been installed properly and that they are
in good working order.
For removal, overhaul and reassembly operations use only tools provided with metric meas-
ures. Metric bolts, nuts and screws are not interchangeable with coupling members with
English measurement. Using unsuitable coupling members and tools may damage the
scooter.
Should any interventions to the scooter electrical system be required, check that the elec-
trical connections - especially earth and battery connections - have been implemented
properly.
X9 Evolution 500 Characteristics
CHAR - 7
-
8/6/2019 X9 500 Evo Workshop Manual
8/434
Vehicle identification
VEHICLE IDENTIFICATIONSpecification Desc./QuantityChassis prefix ZAPM 27000 4000001Engine prefix M271M 1001
Dimensions and mass
WEIGHT AND DIMENSIONS
Specification Desc./Quantity
Total dry weight 206 KgWidth (at the mirrors) 910 mm
Wheel base 2130 mmLength 1530 mm
Height (at the saddle) 780 mmHeight at the windscreen (high position) 1450 mm
Characteristics X9 Evolution 500
CHAR - 8
-
8/6/2019 X9 500 Evo Workshop Manual
9/434
Engine
ENGINESpecification Desc./Quantity
Engine Single-cylinder, four-strokeBore 92 mm
Stroke 69 mmCubic capacity 460 cm
Compression ratio 10.5: 1Timing system Single overhead camshaft with integrated tone wheel, control
from flywheel side chain, 4 valves and automatic start-up valvelifting device.
Valve clearance: intake 0.15 mm (when cold)Valve clearance: discharge 0.15 mm (when cold)Valve clearance adjustment By threaded adjuster on the rockers
Engine idle speed 1500 50 rpmAir filter Dry paper filter.
CO % value (measured at the intake manifold) 1 - 1.5%Starting system Electric starter system with freewheel.
Lubrication By trochoidal pump (inside the crankcase), pressure adjust-ment by-pass and oil filter.
Lubrication pressure 4 barMinimum allowed (at 100C) 0.8 bar
Fuel supply Electronic injection system with electric fuel pump, 38 mmthrottle body and single injector.
Max. power (at crankshaft) 29.5 kW at 7500 rpmMax. torque (at crankshaft) 43 Nm at 5500 rpm
Cooling system Fluid circulation through a motor-driven pump, 3-way thermo-stat and electric fan.
X9 Evolution 500 Characteristics
CHAR - 9
-
8/6/2019 X9 500 Evo Workshop Manual
10/434
Transmission
TRANSMISSIONSSpecification Desc./Quantity
Transmission With automatic expandable pulley variator with torque server,V belt, automatic clutch, gear reduction unit and transmission
housing with forced air circulation cooling.
Capacities
CAPACITIESSpecification Desc./Quantity
Cooling system approx. 1.8 lFuel tank (including reserve ~ 2.5 l) ~ 14,5 l
Rear hub ~ 250 ccEngine oil (empty) 1.7 lt.
Engine oil (at oil and filter change) 1.5 lt.
Electrical system
ELECTRICAL COMPONENTS
Specification Desc./Quantity
1 Ignition type Inductive, high efficiency, integrated with injection, vari-able advance and separate HV coil.
2 Spark advance (before TDC) Variable, controlled by the injection controller3 Spark plug CHAMPION RG6YC; NGK CR7EKB4 Battery 12V-14Ah5 Fuses n.1 70A_n.1 30A_n.2 15A_n.3 10A_n.4 7,5A_n.2 5A_n.
1 3A6 Generator in three-phase alternating current
Frame and suspensions
FRAME AND SUSPENSIONSSpecification Desc./Quantity
Type Welded structure consisting of steel pipes with asymmetricaltrestle structure, front crosspieces and union members made
of sheet steel.Front suspension Hydraulic telescopic fork with dual effect, 40 mm stems and
back pin with couplongs for dual brake calipers.Front fork stroke 104 mmRear suspension Engine based on oscillating fork pivoted to the chassis by 2-
freedom degree oscillating arm and pair of dual effect hydraulicshock absorbers with 4-position preload adjustment
Rear suspension range 76.6 mm (minimum spring preload)
X9 Evolution 125-250-500:
Please take note that, starting from chassis serial number ZAPM2300003509521, the front small chas-
sis fixing system has changed in order to improve its locking to the chassis. Therefore we have
introduced:
N2 screws drawing 432142
N2 4x11x0 external teeth spring washers drawing 012533 N2 nuts drawing 968224
Characteristics X9 Evolution 500
CHAR - 10
-
8/6/2019 X9 500 Evo Workshop Manual
11/434
Front fork
This is to inform you that, starting from frame no. ZAPM2700004008122, the front fork has been re-
placed to improve comfort. The new suspension differs from the previous one for a different stiffness
of the springs and a higher quantity of oil: from 268 cc to 273 cc 2 cc of Selenia Fork 7.5 W
Brakes
BRAKESSpecification Desc./Quantity
Front Disc brake 260 (vehicle RH side), with hydraulic commandactivated from handlebars with right-hand lever and 2 piston
floating caliper.Combined With dual disc brake, 260 front LH with 2 piston floating cal-
iper and 240 rear, with 2 opposed piston floating caliper.
Hydraulic command activated from handlebars with left-handlever. The system is interlocked with a pressure distribution
valve.
Wheels and tyres
WHEELS AND TYRESSpecification Desc./Quantity
Light alloy rims (Front): 3,50x14"Light alloy rims (rear): 4,50x14"
Tyre pressure (when cold): front 2,2 barTyre pressure (when cold): rear 2,4 bar (2,6 bar with passenger or optional trunk on)
Front Tyre Michelin Gold Standard 120/70-14' M/C reinforced TL 55 SManufacturer / Model / Size Pirelli GTS 23 120/70_14'M/C TL 55 S
Rear Tyre Michelin Gold Standard 150/70-14' M/C TL 66 SManufacturer / Model / Size Pirelli GTS 24 150/70_14' M/C TL 66 S
CAUTION
IT IS MANDATORY TO ADOPT EXCLUSIVELY "S" CLASS TYRES, WHICH GUARANTEE COR-RECT VEHICLE PERFORMANCE AT THE DIFFERENT SCOOTER SPEEDS. USING ANY OTHERTYRE MAY RESULT IN VEHICLE INSTABILITY. IT IS ADVISABLE TO USE TYRE TYPES REC-OMMENDED BY PIAGGIO.
X9 Evolution 500 Characteristics
CHAR - 11
-
8/6/2019 X9 500 Evo Workshop Manual
12/434
Tightening Torques
STEERING UNITName Torque in Nm
Steering wheel upper ring nut 36 39Steering wheel lower r ing nut 10 13 then loosen by 90(see "Steering wheel ring nut lock-
ing")Handlebar fixing screw (*) 43 47
STEERING WHEEL LOCKING RING NUT
1) Apply to the lower ring nut a setting torque of 2025 Nm then loosen it.
2) Tighten the ring nut again at a torque of 1013 Nm.
3) Loosen the lower ring nut by 90.
4) Insert the spacer.
5) Lock the upper ring nut at a torque of 36 39 Nm
CHASSIS UNIT
Name Torque in Nm
Oscillating arm pin right nut - Engine 100 120Oscillating arm pin left nut - Engine 56 70
Oscillating arm-chassis pin 14 17Oscillating arm-chassis pin lock nut 40 50
Oscillating arm pin right nut - Chassis 66 73Side stand support fixing bolt 33 41
Bolt fixing the centre stand to the frame 25 30Hydraulic actuator fixing screw to chassis 20 25
Side stand screw 35 40Side stand switch screw 5 7
Side stand nut 40 45Oscillating arm damper bar nut 33 41Damper pad support plate nut 33 41
FRONT SUSPENSIONName Torque in Nm
Fork leg tightening clamp screw 20 25Front wheel axle 45 50
Wheel axle tightening clamp screw 6 7Front mudguard fixing screw 5 6,5
Pumping fixing screw to fork leg 45 50
FRONT BRAKEName Torque in Nm
Screw for fixing the caliper support to the fork 42 62Brake fluid pump-hose fitting 16 20Brake fluid pipe-calliper fitting 16 20
Disc tightening screw () 5 6Oil drainage screw 12 16
REAR SUSPENSIONName Torque in Nm
Right and left shock absorber support fixing 20 25Shock absorbers fixing to chassis 33 41
Shock absorbers fixing to lower supports 33 41Rear wheel axle 104 126
Rear wheel rim screws 33 37Silencer support arm fixing to engine 33 42
Characteristics X9 Evolution 500
CHAR - 12
-
8/6/2019 X9 500 Evo Workshop Manual
13/434
COMBINED BRAKEName Torque in Nm
Oil pipe union on combined brake pump 16 20Combined brake pipe union on front calipers 16 20
Combined brake pipe union on rear calipers 16 20Front brake caliper pipe union on combined braking device 20 25Rear brake caliper pipe union on combined braking device 20 25
Brake caliper fixing screw to supports 20 25Rear disc tightening screw () 14 17
Oil bleed screw 12 - 16Rear brake caliper fastening screw to engine 20 25
Rear brake piping support fixing screw to engine 5 6,5Rear brake piping support fixing screw to chassis 9 11
SILENCER
Name Torque in Nm
Manifold fixing screw to silencer 16 18Silencer support bracket fixing screw to engine 33 41
Silencer heat guard fixing screw 3 4Exhaust gas inlet screw 22 26
ENGINE UNITName Torque in Nm
Clutch locking nut 65 75Driven pulley shaft support fixing screw 23 26
Belt anti-flapping roller fixing screw 17 20Driving pulley nut () 160 175
Flywheel nut () 115 125Driven pulley nut 92 100
Half-crankcase union screw 11 13Head cover screws 11 13Head nuts () () (*) 38 42
Cylinder stud bolts 44 46Camshaft bell screw (#) 30 35
Camshaft plate fixing screw (#) 4 6Valve clearance adjustment lock nut 6 8
Water pump impeller 4 6Starter motor fastening screw 11 13
Ignition spark plug 12 14Hub oil drainage cap 15 17Rear hub cap screw 24 27
Transmission cover screw 11 13Oil pump head screw 8 10
Engine oil drainage cap 24 30Water pump cover screw 3 4
Screw fixing the oil pump to the crankcase 5 6Stator fastening screw 8 10
Screw fixing the start-up free wheel to the flywheel (#) 13 15Flywheel cover screw 11 13
Head intake manifold screw 11 13Screw fixing the throttle body to the manifold 11 13
Chain tightener sliding block screw (#) 10 14Timing chain tensioner central screw 5 - 6Timing chain tensioner support screw 11 13Counter-rotating shaft fixing nut (#) 25 29
Screw fixing the silencer to the support arm 20 25Exhaust manifold - cylinder nuts 27 33
Screw fixing the rear brake caliper support bracket to the en-gine
20 25
Driving shaft timing cap 3,5 4,5Head water outlet cover screw 3 4
Calibrated dowel 5 7
Oil cap with level bar 1,5 2,5Oil filter 12 16
Oil filter engagement union 18 22
X9 Evolution 500 Characteristics
CHAR - 13
-
8/6/2019 X9 500 Evo Workshop Manual
14/434
Name Torque in Nm
Oil vent pipe fixing 3 4Minimum oil pressure sensor 12 14
Fairlead bracket fixing 3 4Head/Cylinder/Crankcase fixing 10 12
Revolution timing sensor fixing screw 3 4
Coolant temperature sensor 10 12Pressure reducer counterweight retainer 7 8.5
Counter shaft gear fixing on driving shaft (#) 10 12Thermostat cover 1,5 2
Start-up rim counter shaft plate fixing 3 4Injector support fixing (#) 3 4
Head lubrication control jet 5 - 7
()Lubricate parts before fitting.
(^) Apply LOCTITE for surfaces type 510.
(#) Apply thread-holding LOCTITE medium type 242.
() 1st locking: 20 Nm crossed, locking at torque 38 - 42 Nm crossed, crossed loosening.
(*) 2nd tightening: 20 Nm crossed, locking at torque 38 - 42 Nm crossed.N.B.
LUBRICATE THE THREADS.
NOTICE OF TECHNICAL SERVICING
For correct tightening, the expansion tank cap locking torque has been standardised to 2.5 Nm
Please take note that we have normalized to 17 - 20 Nm the temperature sensor locking torque, in order
to guarantee a correct locking
This is to inform you that the tightening torque forscrews with dwg. no. 842502 has been increased
from 8-10 Nm to 14-16 Nm, to prevent the exhaust
pipe from coming loose.
Overhaul data
This section provides the main information for scooter servicing.
Assembly clearances
Characteristics X9 Evolution 500
CHAR - 14
-
8/6/2019 X9 500 Evo Workshop Manual
15/434
Cylinder - piston assy.
(Values in mm)
HEIGHT AT WHICH THE DIAMETER SHOULD BE MEASUREDSpecification Desc./Quantity
A: 10 mmB: 43 mm
CATEGORIES OF COUPLINGName Initials Cylinder Piston Play on fitting
Cylinder Piston A 91.990 - 91.997 91.954 - 91.961 0.029 - 0.043Cylinder Piston B 91.997 - 92.004 91.961 - 91.968 0.029 - 0.043Cylinder Piston C 92.004 - 92.011 91.968 - 91.975 0.029 - 0.043Cylinder Piston D 92.011 - 92.018 91.975 - 91.982 0.029 - 0.043
N.B.
THE PISTON MUST BE INSTALLED WITH THE ARROW FACING TOWARDS THE EXHAUST SIDE,
THE PISTON RINGS MUST BE INSTALLED WITH THE WORD TOP OR THE STAMPED MARKFACING UPWARDS.
Piston rings
* Fit rings 2 and 3 with the word TOP facing upwards.
** Position the openings in the rings as shown here.
*** Value A of sealing ring inside the cylinder
**** Ring opening
X9 Evolution 500 Characteristics
CHAR - 15
-
8/6/2019 X9 500 Evo Workshop Manual
16/434
SEALING RINGSName Initials Cylinder Piston Play on fitting
1st Compression ring A 0.15 0.35 0.5 Middle piston ring A 0.25 0.50 0.65
Oil scraper ring A 0.25 0.50 0.65
Crankcase - crankshaft - connecting rod
Characteristic
Drive shaft / crankcase axial clearance:
0.1 - 0.5 mm (when cold)
AXIAL CLEARANCE BETWEEN CRANKSHAFT AND CONNECTING ROD
Name Description Dimensions Initials Quantity
Transmission-sideshoulder
0.8 0.025 A D= 0.20 - 0.40
Transmission-side half-shaft
19.6 + 0.050 B D= 0.20 - 0.40
Connecting rod 22 0.10-0.15 C D= 0.20 - 0.40Flywheel-side shoulder 13 0.025 F D= 0.20 - 0.40
Flywheel-side half-shaft 19.6 +0.050 E D= 0.20 - 0.40Complete drive shaft 63.5+0.1-0.05 G D= 0.20 - 0.40
Characteristics X9 Evolution 500
CHAR - 16
-
8/6/2019 X9 500 Evo Workshop Manual
17/434
Diameter of crankshaft bearings.
Measure the capacity on both axes x-y.
CRANKSHAFTSpecification Desc./Quantity
Cat. 1 Standard diameter: 40.010 40.016Cat. 2 Standard diameter: 40.016 40.022
Crankshaft alignment
Specific tooling
020335YMagnetic support for dial gauge
MAX. ADMISSIBLE DISPLACEMENTSpecification Desc./Quantity
A = 0.15 mmB = 0.010 mmC = 0.010 mmD = 0.10 mm
Crankcase / countershaft coupling
Besides considering it should match the crankshaft, the crankcase is chosen according to the centre
to centre distance between the seat of the crankshaft and that of the contra-rotating shaft.
Both the centre to centre distance and the pair of gears driving the contra-rotating shaft are divided into
two types (A and B) to be matched (A with A and B with B).
This selection is useful to keep the difference between the working distance of the gears and their
distance without clearance at a given value in order to avoid abnormal noise.
TYPE ASpecification Desc./Quantity
Centre to centre distance of the gears without clearance 76.937 76.867Centre to centre distance on the crankcase 77.022 76.992
TYPE BSpecification Desc./Quantity
Centre to centre distance of the gears without clearance 76.907 76.837
X9 Evolution 500 Characteristics
CHAR - 17
-
8/6/2019 X9 500 Evo Workshop Manual
18/434
Specification Desc./Quantity
Centre to centre distance on the crankcase 76.992 76.962
The gears with centre to centre distance without clearance between 76.867 and 76.907 are considered
universal and can be fitted to either crankcase type.
Either the pair of gears or the crankcase is identified with the letter referring to the type (on the crank-
case, this mark is found at the cylinder mouth, flywheel side).
Slot packing system
Shimming system for limiting the compression ratio Rc = 10.5 : 1
DISTANCE "A" IS A PROJECTION OR RECESS VALUE OF THE PISTON TOP FROM THE CYL-INDER PLANE.DISTANCE "A" ALLOWS THE THICKNESS OF THE GASKET TO BE DETERMINED THAT HAS TOBE FITTED TO THE CYLINDER HEAD IN ORDER TO RESTORE THE COMPRESSION RATIO. THE
BASE GASKET MUST BE THICKER, THE MORE THE PLANE FORMED BY THE PISTON TOPPROTRUDES FROM THE PLANE FORMED BY THE CYLINDER HEAD. ON THE OTHER HAND,THE MORE THE PISTON TOP IS RECESSED INTO THE CYLINDER TOP PLANE, THE SMALLERTHE GASKET THICKNESS.
BASE GASKET THICKNESSName Measure A Thickness
A MEASURE TAKEN - 0.185 - - 0.10 0.4 0.05A MEASURE TAKEN - 0.10 - + 0.10 0.6 0.05A MEASURE TAKEN + 0.10 + 0.185 0.8 0.05
N.B.
VALUES INDICATED WITH - REFER TO PISTON CROWN RECESSES WITH RESPECT TO THECYLINDER PLANE.
Characteristics X9 Evolution 500
CHAR - 18
-
8/6/2019 X9 500 Evo Workshop Manual
19/434
Products
PRODOTTIProduct Description Specifications
AGIP ROTRA 80W-90 Rear hub oil SAE 80W/90 Oil that exceeds the re-quirements of API GL3 specifications
AGIP FILTER OIL Oil for air filter sponge Mineral oil with specific additives for in-creased adhesiveness
AGIP CITY HI TEC 4T Engine oil SAE 5W-40, API SL, ACEA A3, JASO MASynthetic oil
AGIP BRAKE 4 Brake fluid FMVSS DOT 4 Synthetic fluidSPECIAL AGIP PERMANENT fluid coolant Monoethylene glycol-based antifreeze
fluid, CUNA NC 956-16AUTOSOL METAL POLISH Muffler cleaning paste special product for cleaning and polishing
stainless steel mufflerAGIP GP 330 Grease for brake levers, throttle White calcium complex soap-based
spray grease with NLGI 2; ISO-L-XBCIB2AGIP CITY TEC 2T Mixer oil synthetic oil for 2-stroke engines: JASO
FC, ISO-L-EGD
ARNICA 46 Electro-hydraulic centre-stand Highly viscous oil for hydraulic controls
X9 Evolution 500 Characteristics
CHAR - 19
-
8/6/2019 X9 500 Evo Workshop Manual
20/434
INDEX OF TOPICS
TOOLING TOOL
-
8/6/2019 X9 500 Evo Workshop Manual
21/434
SPECIFIC TOOLINGStores code Description
001330Y Tool for fitting steering seats
001467Y002 Driver for OD 73 mm bearing
001467Y006 Pliers to extract 20 mm bearings
001467Y007 Driver for OD 54-mm bearings
001467Y008 Pliers to extract 17 mm bearings
001467Y017 Driver for OD 36 mm bearings
X9 Evolution 500 Tooling
TOOL - 21
-
8/6/2019 X9 500 Evo Workshop Manual
22/434
Stores code Description
001467Y031 Bell
001467Y034 Pliers to extract 15-mm bearings
001467Y035 Belle for OD 47-mm bearings
002465Y Pliers for circlips
020004Y Punch for removing fifth wheels fromheadstock
020055Y Wrench for steering tube ring nut
Tooling X9 Evolution 500
TOOL - 22
-
8/6/2019 X9 500 Evo Workshop Manual
23/434
Stores code Description
020074Y Support base for checking crankshaftalignment
020150Y Air heater support
020151Y Air heater
020193Y Oil pressure gauge
020306Y Punch for assembling valve seal rings
020329Y MityVac vacuum-operated pump
X9 Evolution 500 Tooling
TOOL - 23
-
8/6/2019 X9 500 Evo Workshop Manual
24/434
Stores code Description
020330Y Stroboscopic light to check timing
020331Y Digital multimeter
020333Y Single battery charger
020334Y Multiple battery charger
020335Y Magnetic support for dial gauge
020358Y 37x40-mm adaptor
Tooling X9 Evolution 500
TOOL - 24
-
8/6/2019 X9 500 Evo Workshop Manual
25/434
Stores code Description
020359Y 42x47-mm adaptor
020360Y Adaptor 52 x 55 mm
020363Y 20 mm guide
020364Y 25-mm guide
020375Y Adaptor 28 x 30 mm
020376Y Adaptor handle
020382Y012 bush (valve removing tool)
X9 Evolution 500 Tooling
TOOL - 25
-
8/6/2019 X9 500 Evo Workshop Manual
26/434
Stores code Description
020412Y 15 mm guide
020431Y Valve oil seal extractor
020434Y Oil pressure control fitting
020439Y 17 mm guide
020444Y Tool for fitting/ removing the driven pulleyclutch
Tooling X9 Evolution 500
TOOL - 26
-
8/6/2019 X9 500 Evo Workshop Manual
27/434
Stores code Description
020444Y009 46x55 Wrench
020456Y 24 mm adaptor
020458Y Puller for lower bearing on steering tube
020459Y Punch for fitting bearing on steering tube
020460Y Scooter diagnosis and tester
X9 Evolution 500 Tooling
TOOL - 27
-
8/6/2019 X9 500 Evo Workshop Manual
28/434
Stores code Description
020467Y Flywheel extractor
020468Y Piston fitting band
020469Y Reprogramming kit for scooter diagnosistester
020470Y Pin retainers installation tool
020471Y Pin for countershaft timing
Tooling X9 Evolution 500
TOOL - 28
-
8/6/2019 X9 500 Evo Workshop Manual
29/434
Stores code Description
020472Y Flywheel lock wrench
020474Y Driving pulley lock wrench
020475Y Piston position checking tool
020476Y Stud bolt set
020477Y Adaptor 37 mm
020478Y Punch for driven pulley roller casing
X9 Evolution 500 Tooling
TOOL - 29
-
8/6/2019 X9 500 Evo Workshop Manual
30/434
Stores code Description
020479Y Countershaft lock wrench
020480Y Petrol pressure check set
020481Y Control unit interface wiring
020482Y Engine support
020483Y 30 mm guide
020512Y Piston fitting fork
Tooling X9 Evolution 500
TOOL - 30
-
8/6/2019 X9 500 Evo Workshop Manual
31/434
Stores code Description
020527Y Engine support base
020565Y Flywheel lock calliper spanner
020604Y011 Fitting adapter494929Y Exhaust fumes analyser
X9 Evolution 500 Tooling
TOOL - 31
-
8/6/2019 X9 500 Evo Workshop Manual
32/434
INDEX OF TOPICS
MAINTENANCE MAIN
-
8/6/2019 X9 500 Evo Workshop Manual
33/434
Maintenance chart
Adequate maintenance is fundamental to ensuring long-lasting, optimum operation and performance
of your vehicle.To this end, a series of checks and maintenance operations (at the owner's expense) have been sug-
gested, which are included in the summary table on the following page. Any minor faults should be
reported without delay to an Authorised Service Centre or Dealer without waiting until the next
scheduled service to solve it.
All scheduled maintenance services must be carried out at the specified intervals, even if the stated
mileage has not yet been reached. Punctual scooter servicing is essential to ensure your warranty
remains valid. For any further information concerning Warranty procedures and "Scheduled Mainte-
nance", please refer to the "Warranty Booklet".
EVERY 2 YEARS
60'Action
Coolant - changeBrake fluid - change
EVERY 3,000 KMAction
Engine oil - level check/ top-upBrake pads - check condition and wear
AFTER 1,000 KM OR 4 MONTHS
90'Action
Engine oil - replacementHub oil - changeCarburetion - check/adjustSeals/injection system hoses - visual checkBase vent - checkSteering - adjustmentBrake control levers - greasingBrake fluid level - checkSafety locks - checkElectrical system and battery - check
Vehicle and brake test - road test
X9 Evolution 500 Maintenance
MAIN - 33
-
8/6/2019 X9 500 Evo Workshop Manual
34/434
AFTER 6,000 KM OR 12 MONTHS
80'Action
Engine oil - replacementHub oil - level checkSpark plug / electrode gap - checkAir filter - cleaningEngine oil - changeValve clearance - checkBase vent - checkVariable speed rollers - replacementDriving belt - checkingCoolant level - checkBrake fluid level - checkElectrical system and battery - checkTyre inflation and wear - CheckVehicle and brake test - road test
AFTER 12,000 KM OR 24 MONTHS AND 60,000 KM205'
Action
Engine oil - replacementHub oil - level checkSpark plug/electrode gap - replacementAir filter - cleanEngine oil - changeCarburetion - check/adjustSeals/injection system hoses - visual checkBase vent - checkVariable speed rollers - replacementRoller support sliding blocks - check/changeDriving belt - replacement
Coolant level - checkSteering - adjustmentBrake control levers - greasingTransmission elements - lubricationBrake fluid level - checkSafety locks - checkSuspensions - checkElectrical system and battery - checkHeadlight - adjustmentTyre pressure and wear - checkVehicle and brake test - road test
AFTER 18,000 KM AND AFTER 54,000 KM
150'Action
Engine oil - replacementHub oil - level checkSpark plug / electrode gap - checkAir filter - changeEngine oil - changeValve clearance - checkBase vent - checkVariable speed rollers - replacementDriving belt - checkingCoolant level - checkRadiator - external cleaning/ checkBrake fluid level - checkElectrical system and battery - check
Tyre inflation and wear - CheckVehicle and brake test - road test
Maintenance X9 Evolution 500
MAIN - 34
-
8/6/2019 X9 500 Evo Workshop Manual
35/434
AFTER 24,000 KM
255'Action
Engine oil - replacementHub oil - changeSpark plug / electrode gap - replacementAir filter - cleanEngine oil - changeFuel filter - checkCarburetion - check/adjustSeals/injection system hoses - visual checkBase vent - checkVariable speed rollers - replacementRoller support sliding blocks - check/changeDriven pulley bushing - check / greaseDriving belt - replacementCoolant level - checkSteering - adjustment
Brake control levers - greasingTransmission elements - lubricationBrake fluid level - checkSafety locks - checkSuspensions - checkElectrical system and battery - checkHeadlight - adjustmentTyre inflation and wear - CheckVehicle and brake test - road test
AFTER 30,000 KM, 42,000 KM AND 66,000 KM
80'Action
Engine oil - replacement
Hub oil - level checkSpark plug / electrode gap - checkAir filter - cleaningEngine oil - changeBase vent - checkVariable speed rollers - replacementDriving belt - checkingCoolant level - checkBrake fluid level - checkElectrical system and battery - checkTyre inflation and wear - CheckVehicle and brake test - road test
AFTER 36,000 KM
365'Action
Engine oil - replacementHub oil - level checkSpark plug/electrode gap - replacementAir filter - changeEngine oil - changeValve clearance - checkCarburetion - check/adjustSeals/injection system hoses - visual checkBase vent - checkVariable speed rollers - replacementRoller support sliding blocks - check/changeDriving belt - replacement
Coolant level - checkRadiator - external cleaning/ checkSteering - adjustment
X9 Evolution 500 Maintenance
MAIN - 35
-
8/6/2019 X9 500 Evo Workshop Manual
36/434
Action
Brake control levers - greasingBrake fluid hoses - replacementTransmission elements - lubricationBrake fluid level - checkSafety locks - check
Suspensions - checkElectrical system and battery - checkHeadlight - adjustmentTyre inflation and wear - CheckVehicle and brake test - road test
AFTER 48,000 KM
255'Action
Engine oil - replacementHub oil - changeSpark plug / electrode gap - replacementAir filter - clean
Engine oil - changeFuel filter - replacementCarburetion - check/adjustSeals/injection system hoses - visual checkBase vent - checkVariable speed rollers - replacementRoller support sliding blocks - check/changeDriven pulley bushing - check / greaseDriving belt - replacementCoolant level - checkSteering - adjustmentBrake control levers - greasingTransmission elements - lubricationBrake fluid level - checkSafety locks - check
Suspensions - checkElectrical system and battery - checkHeadlight - adjustmentTyre inflation and wear - CheckVehicle and brake test - road test
AFTER 72,000 KM
405'Action
Engine oil - replacementHub oil - changeSpark plug / electrode gap - check / replacementAir filter - changeEngine oil - change
Fuel filter - checkValve clearance - checkCarburetion - check/adjustSeals/injection system hoses - visual checkBase vent - checkVariable speed rollers - replacementRoller support sliding blocks - check/changeDriven pulley bushing - check / greaseDriving belt - replacementCoolant level - checkRadiator - external cleaning/ checkSteering - adjustmentBrake control levers - greasingBrake fluid hoses - replacementBrake fluid level - checkSafety locks - checkSuspensions - check
Maintenance X9 Evolution 500
MAIN - 36
-
8/6/2019 X9 500 Evo Workshop Manual
37/434
Action
Electrical system and battery - checkHeadlight - adjustmentTyre inflation and wear - CheckVehicle and brake test - road testTransmission elements - lubrication
Spark plug
Check and replacement
CAUTION
THE SPARK PLUG MUST BE REMOVED WITH COLD EN-GINE. THE SPARK PLUG SHOULD BE CHECKED EVERY6,000 KM AND REPLACED EVERY 12,000 KM. THE USE OFNON-CONFORMING IGNITION CONTROL UNITS ANDSPARK PLUGS OTHER THAN THOSE PRESCRIBED CANSERIOUSLY DAMAGE THE ENGINE.
CharacteristicRecommended spark plugs:
CHAMPION RG6YC - NGK CR 7 EKB
- Position the scooter on centre stand.
- Open the door on the left side and remove the relevant screw lifting from the lower part in the specific
groove.
- Disconnect the shielded spark plug cap
- Unscrew the spark plug.
- Check the conditions of the spark plug, make sure the insulation is intact, that the electrodes are not
excessively worn or grimy, the conditions of the washer, and measure the distance between the elec-
trodes using the appropriate feeler gauge.
Characteristic
Electrode gap
0.7-0.8 mm
Adjust the gap if necessary, carefully bending the
earth electrode. In the event of irregularity, replace
the spark plug with a recommended type.
- Fit the spark plug with the correct inclination and
manually screw it all the way down, then use the
special spanner to tighten it.
Locking torques (N*m)
Spark plug12 14
- Insert the cap onto the spark plug and proceed with the reassembly operations.
Hub oil
X9 Evolution 500 Maintenance
MAIN - 37
-
8/6/2019 X9 500 Evo Workshop Manual
38/434
Check
- Take the vehicle to a flat ground and rest it on the
central stand.
- Unscrew the oil bar A, dry it with a clean cloth
and reinsert it, screwing it in thoroughly;
- Pull out the bar and check that the oil level is be-
tween the MAX and MIX levels indicated on the
bar (see figure); if the level is below the MIN value,
restore the proper amount of oil in the hub.
- Screw the oil bar back on, checking that it is tight-
ly in place.
N.B.
THE NOTCHES ON THE HUB OIL LEVEL BAR, WITH THEEXCEPTION OF THOSE INDICATING THE MAX AND MINLEVEL, REFER TO SOME OF THE MANUFACTURER'SOTHER MODELS AND HAVE NO SPECIFIC FUNCTION ASFAR AS REGARDS THIS VEHICLE.
Replacement
- Prepare a suitable container.
- Remove the oil drainage cap B and let the oildrain out completely.
- Tighten the drainage cap again and fill the hub
with oil.
Recommended products
AGIP ROTRA 80W-90rear oil hub
SAE 80W/90 Oil that exceeds the requirements of
API GL3 specifications
CharacteristicRear hub oil
250 cc
Maintenance X9 Evolution 500
MAIN - 38
-
8/6/2019 X9 500 Evo Workshop Manual
39/434
Air filter
- Raise the saddle.
- Remove the piston ring and the battery cover.
- Loosen the 4 mounting screws shown in the fig-
ure.
- Loosen the mounting screw located under the in-
take manifold.
- Replace the air filter and reassemble the various
components, reversing the removal procedure.
X9 Evolution 500 Maintenance
MAIN - 39
-
8/6/2019 X9 500 Evo Workshop Manual
40/434
- An inspection and possible cleaning (with com-
pressed air) of the air filter is scheduled every 6000
km in any case.
- The air jet must be directed from the inside to theoutside of the filter (i.e. opposite the direction of
the air flow during normal operation of the engine).
- Any deposits of condensate out of the engine oil
caused by blow-by can be removed via the pipe
shown in the figure.
N.B.
FAILURE TO OBSERVE THE RULES REGARDING CLEANING OF THE FILTER ELEMENT CANLEAD TO IMPROPER LUBRICATION OF THE ELEMENT. POOR LUBRICATION AFFECTS THE
FILTERING CAPACITY. EXCESSIVE LUBRICATION AS WITH A SOILED FILTER CAUSES ANEXCESSIVELY RICH FUEL/AIR MIXTURE.
CAUTION
WHEN TRAVELLING ON DUSTY ROADS, THE AIR FILTER MUST BE CLEANED MORE OFTENTHAN SHOWN IN THE SCHEDULED MAINTENANCE CHART.
WARNING
DO NOT RUN THE ENGINE IF THE AIR FILTER IS NOT IN PLACE THIS WILL RESULT IN EXCES-SIVE WEAR TO ALL THE PARTS OF THE COOLING SYSTEM.
Engine oil
In 4T engines, the engine oil is used to lubricate the distribution elements, the bench bearings and the
thermal group. An insufficient quantity of oil can cause serious damage to the engine.
In all 4T engines, the deterioration of the oil characteristics, or a certain consumption should be con-
sidered normal, especially if during the run-in period. Consumption levels in particular can be influenced
by the conditions of use (e.g.: oil consumption increases when driving at "full throttle".
Check
This operation must be carried out with the engine
cold and following the procedure below:
1) Rest the vehicle on the central stand and on a flat ground.
2) Unscrew the cap/dipstick "A", dry it with a clean cloth and reinsert it, screwing it thoroughly.
3) Remove the cap/dipstick again and check that the level is between the max. and min levels; top-up,
if required.
Topping up from the MIN to MAX. level requires around 1700 cc.
If the check is carried out after the vehicle has been used, and therefore with a hot engine, the level
line will be lower; in order to carry out a correct check it is necessary to wait at least 10 minutes afterthe engine has been stopped, so as to get the correct level.
Maintenance X9 Evolution 500
MAIN - 40
-
8/6/2019 X9 500 Evo Workshop Manual
41/434
Oil top up
The oil should be topped up after having checked the level and in any case by adding oil without ever
exceeding the MAX. level.
The restoration level between the MIN and MAX levels implies a quantity of oil of approx. 400 cc.
Engine oil filter
CAUTION
DO NOT DISPOSE OF OIL IN THE ENVIRONMENT. OIL, GASKET AND FILTER SHOULD BE DIS-POSED OF ACCORDING TO THE REGULATIONS IN FORCE.WARNING
AVOID TOUCHING PARTS OF THE ENGINE WHEN HOT, AS THIS MAY CAUSE BURNS.
- Remove the muffler.
- Remove the filler plug.
- Remove and clean the mesh pre-filter of the drain
cap with compressed air.
- Use a belt spanner for filters to remove cartridge
filter "C".
- Make sure the pre-filter and drain cap O-rings are
in good condition.
- Lubricate them and refit the mesh filter and oil
drain cap by tightening to the prescribed torque.
- Refit a new cartridge filter making sure to lubri-
cate the O-ring before fitting, then screw until it
comes into contact with the seal and further tighten
to the prescribed torque.
- Refit the muffler.- Add recommended engine oil.
X9 Evolution 500 Maintenance
MAIN - 41
-
8/6/2019 X9 500 Evo Workshop Manual
42/434
- Start the engine and let it run for a few minutes and then turn it off.
After 5 minutes check the level and top up, if necessary, never exceed the MAX. level.
N.B.
IF THE OIL IS CHANGED WITHOUT CHANGING THE CARTRIDGE FILTER (1ST COUPON) ADDAROUND 1500 CC OF OIL INSTEAD OF 1700 CC SINCE PART OF THE LUBRICATION CIRCUITIS FILLED.
Characteristic
Engine oil:
1700 cm
Locking torques (N*m)
Engine oil drainage plug24 30Engine oil filter12 - 16
Oil pressure warning light
The vehicle is equipped with a warning light on the
instrument panel that lights up when the key is
turned to the ON position. However, this light
should switch off once the engine has been star-
ted.
If the light turns on during braking, at idling
speed or while turning a corner, it is necessary
to check the oil level and the lubrication sys-tem.
Checking the ignition timing
- Using a TORX wrench, remove the timing check
cap located on the flywheel cover.
- Remove the transmission cover to access the
driving pulley fastening nut that allows the driving
shaft rotation.- Remove the head cover as described in the Ther-
mal unit and timing system chapter.
- Turn the driving shaft to make the reference lo-
cated on the magnet support collimate with that on
the flywheel cover (TDC).
- Make sure that the reference on the wheel speed
sensor is aligned with that obtained on the head.
If the reference is located opposed to the index
Maintenance X9 Evolution 500
MAIN - 42
-
8/6/2019 X9 500 Evo Workshop Manual
43/434
obtained on the head, make the driving shaft per-
form a further revolution.
- Check that the two references match perfectly; if
not, remove the timing belt and install it again.
See also
Cylinder assy. and timing system
Checking the valve clearance
- To check the clearance in the valves collimate
the references between the cam shaft control pul-
ley and head.
- Use a feeler to make sure the clearance between
the valve and register screw correspond to the in-
dicated values. If the clearance does not corre-
spond, adjust it by loosening the lock nut using a
screwdriver on the set screw as shown in the fig-ure.
Characteristic
Valve clearance: intake
0.15 mm (when cold)
Valve clearance: discharge
0.15 mm (when cold)
Cooling system
Engine cooling fluid level check
The fluid level inspection should be carried out ev-
ery 6,000 km when the motor is cold, following the
methods indicated below:
- Rest the vehicle on the central stand and on a flat
ground.
- Remove the expansion tank cap and top up, if the
fluid level is near to or below the MIN level into the
X9 Evolution 500 Maintenance
MAIN - 43
http://0.0.0.0/ -
8/6/2019 X9 500 Evo Workshop Manual
44/434
expansion tank. The fluid level should always be
between the MIN and MAX level.
- To have an indication of the fluid level, refer to a
notch made in a cylindrical insert, coaxial to thefiller and visible inside it once you remove the
loading cap.
The top side of the notch indicates the MAX level
while the lower one indicates the MIN level.
The cooling fluid consists of a mixture of 50%
demineralised water and ethylene glycol and cor-
rosion inhibitors based anti-freeze solution.
WARNING
TO CHECK THE PRESENCE OF AIR IN THE CIRCUIT, PRO-CEED AS DESCRIBED IN THE COOLING CHAPTER
CAUTION
DO NOT EXCEED THE MAX. LEVEL WHEN FILLING SO ASTO AVOID THE COOLANT ESCAPING FROM THE EXPAN-SION TANK WHEN THE vehicle IS IN USE.
Characteristic
Cooling system
approx. 1.8 l
See also
Cooling system
Level check
The front and rear brake fluid tanks can be ac-
cessed removing the cover located on the right
side of the handlebar cover and the display PICS
on the left side.
To check the level proceed as follows:
- rest the vehicle on the central stand with the han-dlebars in a central position;
- remove cover A loosening the fixing screw
B and check the front brake fluid level;
- remove screws C fixing the display PICS and
check the combined brake fluid level;
The level will go down to a certain extent due to
lining wear.
Maintenance X9 Evolution 500
MAIN - 44
http://0.0.0.0/http://0.0.0.0/ -
8/6/2019 X9 500 Evo Workshop Manual
45/434
Braking system
Level check
- Rest the scooter on a flat ground and on the cen-
tral stand.
- Remove the brake pump cover as shown in the
figure.
- Check the brake fluid level by the special indica-
tor located on the pump, as shown in the figure.
N.B.THE LEVEL TENDS TO DROP AS THE BRAKE PADS GET WORN, A MINIMUM LEVEL SHOULDNOT BE REACHED. IF THE LEVEL IS TOO LOW, CHECK AND FIX THE SYSTEM SEALS, IF RE-
X9 Evolution 500 Maintenance
MAIN - 45
-
8/6/2019 X9 500 Evo Workshop Manual
46/434
QUIRED. TOP UP THE PUMP TANK, IF REQUIRED, CONSIDERING THAT THE "MAX." LEVELMUST ONLY BE OBTAINED WITH NEW PADS.
Top-up
To top up the fluid proceed as follows:
Remove the right cover and/or the PICS display,
then remove the tank cap loosening the relevant
two screws, remove the intermediate rubber mem-
brane and restore the level using the prescribed
fluid without exceeding the max level.
CAUTION
ONLY USE DOT 4-CLASSIFIED BRAKE FLUID.
Recommended productsAGIP BRAKE 4Brake fluid
FMVSS DOT 4 Synthetic fluid
In normal weather conditions, the fluid should be
replaced every 20,000 km or in any case every 2
years.
Never use braking fluid from containers that have
already been opened, or partially used.
CAUTION
THE BRAKE FLUID IS HYGROSCOPIC, THAT IS, IT AB-SORBS MOISTURE FROM THE SURROUNDING AIR. IFTHE LEVEL OF HUMIDITY IN THE BRAKE FLUID EXCEEDSA GIVEN VALUE, BRAKING EFFICIENCY WILL BE RE-DUCED.
CAUTION
AVOID CONTACT OF THE BRAKE FLUID WITH YOUREYES, SKIN, AND CLOTHING. IN CASE OF ACCIDENTALCONTACT, WASH WITH WATER.
WARNING
BRAKE CIRCUIT FLUID IS VERY CORROSIVE; DO NOTLET IT COME INTO CONTACT WITH PAINTED PARTS.
N.B.
SEE THE BRAKING SYSTEM CHAPTER WITH REGARD TOTHE CHANGING OF BRAKE FLUID AND THE BLEEDINGOF AIR FROM THE CIRCUITS.
Headlight adjustment
- Place the vehicle in use conditions, with no load, with tyres inflated at the prescribed pressure on flat
ground at 10 m from a white screen placed in dim light, making sure that the vehicle's axle is perpen-
dicular to the screen.
- Trace a horizontal line on the screen at 70 - 73 cm above ground level.
Maintenance X9 Evolution 500
MAIN - 46
-
8/6/2019 X9 500 Evo Workshop Manual
47/434
- Turn the headlight on, switch on the dipped beam
and check that the horizontal limit line between the
dark zone and the illuminated zone does not fall
above the horizontal line traced on the screen.- Adjust the screw located under the front shield to
change the headlight inclination and the light beam
height.
Checking the end compression pressure
- With the engine cold remove the sparkplug cap.
- Remove the sparkplug.
- Fit a compression testing pressure gauge in the sparkplug seat with a 10 mm sparkplug fitting tightened
to the correct torque.
- With the switch on "ON" wait a few seconds and then disconnect the rpm-timing sensor to disable
operation of the injector and sparkplug.
- Run the engine using the starter motor and with the throttle body fully open, until the reading on the
pressure gauge is stable.
- If the pressure is greater than XX - XX, remove the device and reassemble the vehicle.
- If pressure values lower than those indicated are measured, check the engine rpm used for the test;if under 450 rpm, check the starter system.
When the compression end pressure is under the norm, remove the fitting from the pressure gauge and
pour a few cc of oil in the combustion chamber, rotate the engine (preferably by hand) to lubricate the
cylinder.
Repeat the pressure test:
if the new values are still low check the valve seals.
Higher pressure values of a new engine indicate poor sealing of the parts.
Locking torques (N*m)Spark plug12 14
X9 Evolution 500 Maintenance
MAIN - 47
-
8/6/2019 X9 500 Evo Workshop Manual
48/434
Maintenance X9 Evolution 500
MAIN - 48
-
8/6/2019 X9 500 Evo Workshop Manual
49/434
INDEX OF TOPICS
TROUBLESHOOTING TROUBL
-
8/6/2019 X9 500 Evo Workshop Manual
50/434
Transmission and brakes
Clutch grabbing or performing inadequately
IRREGULAR CLUTCH PERFORMANCE OR SLIPPAGEPossible Cause Operation
Faulty clutch Check that there is no grease on the masses. Check that theclutch mass contact surface with the casing is mainly in thecentre with equivalent characteristics on the three masses.
Check that the clutch casing is not scored or worn in an anom-alous way
Insufficient braking
INSUFFICIENTBRAKINGPossible Cause Operation
Inefficient braking system Check the pad wear (1.5 min). Check that the brake discs arenot worn, scored or warped. Check the correct level of fluid inthe pumps and change brake fluid if necessary. Check there isno air in the circuits; if necessary, bleed the air. Check that the
front brake calliper moves in axis with the disc.Fluid leakage in hydraulic braking system Failing elastic fittings, plunger or brake pump seals, replace
Brakes overheating
BRAKES OVERHEATINGPossible Cause Operation
Rubber gaskets swollen or stuck Replace gaskets.Compensation holes on the pump clogged Clean carefully and blast with compressed air
Brake disc slack or distorted Check the brake disc screws are locked; use a dial gauge anda wheel mounted on the vehicle to measure the axial shift of
the disc.Defective piston sliding Check calliper and replace any damaged part.
Braking vibrations or noise
VIBRATIONSORNOISEWHENBRAKING
Possible Cause Operation
Brake disc slack or distorted Check the brake disc screws are locked; use a dial gauge anda wheel mounted on the vehicle to measure the axial shift of
the disc.
Electrical system
Troubleshooting X9 Evolution 500
TROUBL - 50
-
8/6/2019 X9 500 Evo Workshop Manual
51/434
Battery
BATTERYPossible Cause Operation
Battery This is the device in the system that requires the most frequentattention and the most thorough maintenance. If the vehicle isnot used for some time (1 month or more) the battery needs tobe recharged periodically. The battery runs down completely inthe course of 3 months. If the battery is fitted on a motorcycle,be careful not to invert the connections, keeping in mind thatthe black ground wire is connected to the negative terminal
while the red wire is connected to the terminal marked+.
Turn signal lights malfunction
TURN INDICATOR NOT WORKING
Possible Cause Operation
Electronic ignition device fai lure With the key switch set to "ON" jump the contacts 1 (Blue -Black) and 5 (Red/Blue) on the control unit connector. If by
operating the turn indicator control the lights are not steadilyon, replace the control unit; otherwise, check the cable harness
and the switch.
Steering and suspensions
Controls
STEERING CONTROLS AND SUSPENSIONSPossible Cause Operation
Torque not conforming Check the tightening of the top and bottom ring nuts. If irregu-larities in turning the steering continue even after making the
above adjustments, check the seats on which the ball bearingsrotate: replace them if they are recessed or if the balls are flat-
tened.Steering hardening Check the tightening of the top and bottom ring nuts. If irregu-
larities in turning the steering continue even after making theabove adjustments, check the seats on which the ball bearingsrotate: replace them if they are recessed or if the balls are flat-
tened.Malfunctions in the suspension system If the front suspension is noisy, check: the efficiency of the front
shock absorbers; the condition of the ball bearings and relevant
lock-nuts, the limit switch rubber buffers and the movementbushings. In conclusion, check the tightening torque of thewheel hub, the brake calliper, the shock absorber disk in the
attachment to the hub and the steering tube.Seal fault or breakage Replace the shock absorber Check the condition of wear of the
steering covers and the adjustments.
Heavy steering
STEERING HARDENING
Possible Cause Operation
Torque not conforming Check the tightening of the top and bottom ring nuts.
If irregularities continue in turning the steering even after mak-ing the above adjustments, check the seats in which the ballbearings rotate: replace if they are recessed.
X9 Evolution 500 Troubleshooting
TROUBL - 51
-
8/6/2019 X9 500 Evo Workshop Manual
52/434
Excessive steering play
EXCESSIVE STEERING CLEARANCEPossible Cause OperationEXCESSIVE STEERING CLEARANCE Check the tightening of the top and bottom ring nuts.
If irregularities continue in turning the steering even after mak-ing the above adjustments, check the seats in which the ball
bearings rotate: replace if they are recessed.
Noisy suspension
NOISY SUSPENSION
Possible Cause Operation
NOISY SUSPENSION If the front suspension is noisy, check: the efficiency of the front
shock absorbers; the condition of the ball bearings and relevantlock-nuts, the limit switch rubber buffers and the movementbushings.
Suspension oil leakage
OILLEAKAGEFROMSUSPENSION
Possible Cause Operation
Oil leakage from suspension Service the pumping members and check the sleeves andsealing rings are in good conditions. Replace the damaged
parts
Troubleshooting X9 Evolution 500
TROUBL - 52
-
8/6/2019 X9 500 Evo Workshop Manual
53/434
INDEX OF TOPICS
ELECTRICALSYSTEM ELE SYS
-
8/6/2019 X9 500 Evo Workshop Manual
54/434
ELECTRICAL SYSTEMSpecification Desc./Quantity
1 Outside temperature sensor2 Rear brake stop button3 Light switch with flash4 Indicators switch5 Horn button6 Emergency flashing button7 Front fuse holder box8 Fuse no.3 7,5A9 Horn10 Fuse 15A11 Side stand switch
12 Intercom connectors13 Voltage regulator14 Electric side stand control unit15 Engine stop remote control switch 30A16 Remote electronic controller switch 30A17 No. 2 side stand pump remote control switches18 Fuse 70A19 Fuse holder box with side stand pump base20 LH tai ll ight with sidelights bulb and flashing l ight bulb21 Fuse 7,5A22 Fuse 10A23 Fuse 5A24 Fuse 3A25 No. 2 rear fuse holder boxes for control unit26 Anti-tilting sensor27 Saddle opening actuator28 Intercom control unit
Electrical system X9 Evolution 500
ELE SYS - 54
-
8/6/2019 X9 500 Evo Workshop Manual
55/434
Specification Desc./Quantity
29 Front left-hand direction indicator with bulb30 Analogue instrument unit (5 bulbs)31 Radio display32 Digital instrument unit with no. 11 LED indicators33 Front headlight
34 Front right-hand direction indicator with bulb35 Diode unit36 Diode 6A37 Diode 1A38 Main remote control switch 30A39 Socket 12V40 Helmet compartment glass bowl with lamp41 Rear brake light with no. 5 bulbs42 Number plate light with bulb43 RH tai llight with sidelights bulb and flashing l ight bulb44 Start-up remote control switch45 Battery 12V-14Ah46 Helmet compartment light button47 Starter motor48 No. 3 7.5A fuses49 Fuse holder box50 Fuse 15A51 HV coil52 Connector cap53 Saddle opening button54 Fuel level indicator with pump55 Immobilizer aerial56 Key switch57 Anti-theft alarm fitting58 Electric fan59 Electric fan remote control switch 30A60 Fitting for accessories61 Side stand button62 Start up button63 Reset button64 Actuators control unit65 Engine stop switch66 Decoder67 Front brake stop button68 Wheel rpm sensor69 Injection ECU70 Side stand pump motor71 End of stroke button72 Enable button73 No. 2 buttons with clamp74 Fuel injector75 Throttle potentiometer76 Idle adjustment motor77 Engine rpm sensor
78 Engine rpm sensor79 Engine water temperature sensor80 Stuck relay indicator81 Engine oil pressure sensor82 Magneto flywheel
WIRING COLOUR CHART:
B = White - Bl = Blue - G = Yellow - Mr = Brown - N = Black - BV = White - Green - GN = Yellow - Black
- G = Grey - Rs Pink - R = Red - Vi = Purple - V = Green - VN = Green - Black - BN = White - Black -
BBl = White - Blue - GV = Yellow - Green - Ar = Orange - Az = Light blue - GrBl = Grey - Blue - GrN
= Grey - Black.
CAUTION
X9 Evolution 500 Electrical system
ELE SYS - 55
-
8/6/2019 X9 500 Evo Workshop Manual
56/434
SHOULD ANY INTERVENTIONS TO THE ELECTRIC SYSTEM BE REQUIRED, MAKE SURE THATTHE LEADS TO THE ELECTRONIC IGNITION DEVICE ARE PROPERLY CONNECTED ACCORD-ING TO POLARITY AND TO THE LEAD COLOURS.
Components arrangement
COMPONENTSLOCATION
Specification Desc./Quantity
1 Side stand switch2 Voltage regulator3 Side stand control unit4 Electronic control unit remote control switch5 Engine stop remote control switch6 Service remote control switch7 Fuse holder box (n.3 7.5A, n.1 15A)8 No. 2 start-up remote control switches9 Magneto flywheel 373W10 No. 2 buttons for side stand
11 Side stand pump motor12 Pump unit with level indicator13 Starter motor14 Helmet compartment lighting button15 Helmet compartment glass bowl16 Socket 12V17 No. 2 rear fuse holder boxes for control unit (n.1 3A, n.1
5A, n.1 10A, n.1 3A)18 (Diode holder box (n. 2 6A and 2A diodes)19 Fuse holder box (n.2 7.5A, n.1 15A and 5A)20 Fuse holder box with base for stand pump remote control
switch (n.1 70A)21 Digital instrument unit (11 indicators and led)22 Analogue instrument unit (5 bulbs)23 Headlight with n. 2 position bulbs and n.2 high/low beam
bulbs 55W24 Front LH direction indicator with 10W bulb25 Rear brake stop button
Electrical system X9 Evolution 500
ELE SYS - 56
-
8/6/2019 X9 500 Evo Workshop Manual
57/434
Specification Desc./Quantity
26 Light switch with flash27 Indicators switch28 Horn button29 Emergency flashing button30 Reset button
31 Horn32 LH taill ight with sidelights bulb 5W and flashing light bulb
10W33 Rear tail light with 5 2.3W bulbs34 Number plate light bulb 12V-5W35 Rh taill ight with sidelights bulb 5W and flashing light bulb
10W36 Battery 12V-14Ah37 Front brake stop button38 Engine stop switch39 Wheel rpm sensor40 Front RH direction indicator with 10W bulb41 Main remote control switch42 Light switch43 Start up button
44 Side stand button45 Key switch46 Radio display47 Electric fan remote control48 30A fuse with start-up remote control switch49 Radio/intercom/handsfree control unit50 No. 2 pump remote control switches51 Stuck relay indicator52 No. 2 headlight remote control switches
Conceptual diagrams
Ignition
X9 Evolution 500 Electrical system
ELE SYS - 57
-
8/6/2019 X9 500 Evo Workshop Manual
58/434
IGNITIONSECTIONSpecification Desc./Quantity
1 Anti-theft alarm fitting2 Side stand switch
3 Engine stop switch4 Voltage regulator5 Battery 12V - 4Ah6 Start up button7 Diode 6A8 Starter motor9 Fuse no. 13 30 A10 Remote starter switch11 Main remote control switch12 Diode 2 A13 Key switch contacts14 Two brake light buttons15 Digital instrument unit16 Engine stop remote control switch17 Electronic control unit remote control switch
18 Immobilizer aerial19 Decoder20 HV coil21 Start-up/injection electronic control unit22 Fuse no. 2 10 A23 Fuse no. 3 3A24 Fuse no. 10 7,5A
Headlights and automatic starter section
HEADLIGHTSANDAUTOMATICSTARTERSECTIONSpecification Desc./Quantity
1 Anti-theft alarm fitting2 Bulb for upper beams 12V - 55W3 Bulb for lowerbeams 12V - 55W
Electrical system X9 Evolution 500
ELE SYS - 58
-
8/6/2019 X9 500 Evo Workshop Manual
59/434
Specification Desc./Quantity
4 Light switch5 Side stand switch6 Engine stop switch7 Voltage regulator8 Roof lamp for box helmet illumination with lamp
9 Helmet compartment lighting button10 Battery 12V - 14 Ah11 Fuse no. 13 30 A12 Main remote control switch13 Diode 2 A14 Key switch contacts15 No. 2 bulbs for front sidelight 12V-3W16 License plate light bulb 12V - 5W17 Two (2) taillight bulbs 12V - 5W18 Digital instrument unit19 4 Turn indicator bulbs 12V-10W20 Indicators switch21 Emergency flashing light button (4 direction indicators)22 Engine stop remote control switch23 Connettore per predisposizione accessori24 Start-up/injection electronic control unit25 Fuse no. 5 15 A26 Fuse no. 8 7,5 A27 Fuse no. 4 5 A28 Fuse no. 12 7,5 A29 Fuse no. 11 7,5 A30 Fuse no. 9 15 A
Battery recharge and starting
BATTERYRECHARGEANDSTART-UPSECTIONSpecification Desc./Quantity
1 Side stand switch2 Engine stop switch3 Magneto flywheel
X9 Evolution 500 Electrical system
ELE SYS - 59
-
8/6/2019 X9 500 Evo Workshop Manual
60/434
Specification Desc./Quantity
4 Voltage regulator5 Battery 12V - 4Ah6 Start up button7 Diode 6A8 Starter motor
9 Fuse no. 13 30 A10 Remote starter switch11 Main remote control switch12 Diode 2 A13 Key switch contacts14 Two brake light buttons15 No. 5 bulbs for brake light 12V-2,3W16 Digital instrument unit17 Control unit power supply remote control switch (engine
stop)18 Start-up/injection electronic control unit19 Fuse no. 4 5 A20 Fuse no. 10 7,5A
Level indicators and enable signals section
LEVELINDICATORSANDENABLESIGNALSSECTIONSpecification Desc./Quantity
1 Anti-theft alarm fitting2 Side stand switch3 Engine stop switch4 Saddle opener actuator5 Saddle opening button6 Voltage regulator7 Key switch contacts8 Roof lamp for box helmet illumination with lamp9 Helmet compartment lighting button
10 Battery 12V - 4Ah11 Fuse no. 13 30 A12 Main remote control switch
Electrical system X9 Evolution 500
ELE SYS - 60
-
8/6/2019 X9 500 Evo Workshop Manual
61/434
Specification Desc./Quantity
13 Diode 2 A14 Key switch contacts15 Engine warning indicator16 Engine not enable indicator17 Low fuel warning light
18 High-beam warning light19 Wheel RPM sensor20 Outside temperature sensor21 Digital instrument unit22 Fuel level sender23 Control unit power supply remote control switch (engine
stop)24 Electronic control unit components remote control switch25 Saddle opener receiver26 Pump remote control switches27 Side stand pump motor28 Stuck relay indicator29 Side stand out enable button30 Side stand in enable button31 Electro-hydraulic side stand actuation button
32 Side stand control unit33 Tilting sensor34 Air temperature sensor35 Engine rpm sensor36 Double wire screened cable37 Fuel injector38 Idle adjustment motor39 Fuel pump40 Engine temperature sensor41 Diagnostics socket connector42 Throttle potentiometer43 Start-up/injection electronic control unit44 Fuse no. 5 15A45 Fuse no. 6 10A46 Fuse no. 14 70A47 Fuse no. 2 10A48 Fuse no. 1 5A49 Fuse no. 4 5 A50 Fuse no. 12 7,5 A
Checks and inspections
Battery recharge circuit
The recharge system is provided with a three phase alternator with permanent flywheel.
The alternator is directly connected to the voltage regulator.
This, in its turn, is connected directly to the ground and the battery positive terminal passing through
the 30A protective fuse.
This system therefore requires no connection to the key switch.
The three- phase generator provides good recharge power and at low revs, a good compromise is
achieved between generated power and idle stability.
Stator check
Stator winding check-up
WARNING
THIS CHECK-UP CAN BE MADE WITH THE STATOR PROPERLY INSTALLED.
X9 Evolution 500 Electrical system
ELE SYS - 61
-
8/6/2019 X9 500 Evo Workshop Manual
62/434
1) Remove the door in the saddle compartment.
2) Disconnect the connector between the stator and regulator with the three yellow wires.
3) Measure the resistance between each of the yellow terminals and the other two.
Electric characteristic
Resistance:
0.2 - 1
4) Check that there is insulation between the each yellow cable and the ground.
5) If values are incorrect, replace the stator.
Recharge system voltage check
Look for any leakage
1) Check that the battery does not show signs of leaking fluid before checking the output voltage.
2) Turn the ignition key to OFF and connect the multimeter leads between the battery negative pole (-)
and the Black cable.
3) With the multimeter leads connected, disconnect the Black cable from the battery negative pole (-).
4) With the ignition key always at OFF, the reading indicated by the ammeter must be 0.5 mA.
Maximum current output check.
- With engine off and panel set to "ON" turn on the lights and let the battery voltage set to 12V.
- Connect ammeter pliers to the 2 recharge positive poles in output from the regulator.
- Keep the lights on and start the engine, bring it to normal speed and read the values on the ammeter.
With an efficient battery a value must be detected: > 20A
Check the charging current
WARNING
BEFORE CARRYING OUT THE CHECK, MAKE SURE THAT THE BATTERY IS IN GOOD WORK-ING ORDER.
1) Place the vehicle on its centre stand
2) With the battery correctly connected to the circuit, place the tester terminals between the battery
terminals..
3) Start the engine, ensure that the lights are all out, increase the engine speed and at the same time
measure the voltage.
Electric characteristic
Voltage ranging between 14.0 and 15.0V at 5000 rpm.
VOLTAGE REGULATOR/RECTIFIER
Specification Desc./QuantityType Non-adjustable three-phase transistor
Voltage 14 15V at 5000 rpm with lights off
Electrical system X9 Evolution 500
ELE SYS - 62
-
8/6/2019 X9 500 Evo Workshop Manual
63/434
Lights list
LIGHTS
LIST
Specification Desc./Quantity
1 Dipped beam light N1, 12V-55W, halogen2 Upper beam light N1, 12V-55W, halogen3 Front position lights N2, 12V-3W, all glass4 Front direction indicator lights N2, 12V-10W, spherical5 Rear position lights N2, 12V-5W, spherical6 Stop lights N5, 12V-2,3W, spherical7 Rear turn indicator bulbs Two, 12V-10W, spherical8 Instrument panel lights N5, 12V-2W, all glass9 Helmet compartment light N1, 12V-5W, cylindrical10 Number plate lights N1, 12V-5W, cylindrical
Fuses
The electric system is equipped with:
1. four fuses A into the under saddle compartment.
FUSESpecification Desc./Quantity
1 N.1 Capacity: 15 AProtected Circuits : Socket 12V for users- Under sad-
dle compartment light2 N.1 Capacity: 10 A
Protected Circuits : Saddle opening by button3 N.1 Capacity: 10 A
Protected Circuits : PICS device4 N.1 Capacity: 7,5 A
Protected Circuits : Dipped and high beam bulb
2. five fuses B next to the battery, on the left side.
FUSESpecification Desc./Quantity
1 N.1 Capacity: 70 AProtected Circuits : Electro-hydraulic stand
2 N.1 Capacity: 5 AProtected Circuits : Electro-hydraulic stand
3 N.1 Capacity: 10 AProtected Circuits : Fuel pump - Injector - H.V. coil
4 N.1 Capacity: 3 AProtected circuits: Immobilizer (Decoder and EMS en-
gine management control unit)
X9 Evolution 500 Electrical system
ELE SYS - 63
-
8/6/2019 X9 500 Evo Workshop Manual
64/434
Specification Desc./Quantity
5 N.1 Capacity: 5 AProtected circuits: Diagnostic outlet - Decoder and
control unit enable signal
3. four fuses C into the trunk on the left side.
FUSE
Specification Desc./Quantity
1 N.1 Capacity: 15 AProtected circuits: Horn - High beam bulb - Accesso-
ries2 N.1 Capacity: 7,5 A
Protected circuits: Start-up enable signal - Brake lightlamp
3 N.1 Capacity: 7,5 AProtected circuits: Front and rear position light - Num-
ber plate light4 N.1 Capacity: 7,5 A
Protected circuits: PICS - Saddle opening by remote
control
4. a 30A fuse (main fuse), located next to the bat-
tery on the right side and on the start-up remote
control switch; a spare fuse is provided below it.
Electrical system X9 Evolution 500
ELE SYS - 64
-
8/6/2019 X9 500 Evo Workshop Manual
65/434
Dashboard
Vehicle X9 is provided with an instrument panel
divided into 2 sections: the analogue section is
fixed into the cap while the digital section is integral
to the handlebar.
The analogue section includes:
- Tachometer with dual scale (MPH/KMH) control-
led by the fifth wheel by the digital section;
- RPM counter controlled by the signal sent by the
injection control unit;
- Fuel level indicator controlled by a resistive sen-
sor (into the tank)
- Cooling fluid temperature indicator controlled by
a resistive sensor (on the head)
These instruments are electrical and managed by
stepping motors.
The digital section has the following indications:
- Fuel reserve: amber coloured;
- Position and dipped beam lights: green coloured;
- Upper or passing beams: blue coloured;
- Left direction indicator: green coloured;
- Right direction indicator: green coloured;
- Emergency lights (four direction indicators): red
coloured;
- Engine disabled: red coloured;
- ABS system failure (optional): red coloured;
- Oil pressure: red coloured;
- Injection warning: amber coloured;- ALARM (electro-hydraulic stand): red coloured.
The fuel reserve, direction indicators and emergency flashing functions are activated by the instrument
electronics. For example, the fuel reserve indicator light only turns on when the reserve indication com-
ing from the engine lasts at least 13.5 seconds. This prevents the intermitting turning on of the reserve
light indicator.
- The intermitting function is built in the instrument electronics: this allows operating the emergency
lights with switch in position "OFF" and control switch off. The control switch is only active when the
instrument panel is on.
X9 Evolution 500 Electrical system
ELE SYS - 65
-
8/6/2019 X9 500 Evo Workshop Manual
66/434
To ensure safety while riding, the "direction indicators control" function is connected to the odometer.
If the indicator is left on, it automatically stops after 1 kilometre travelled.
- The "engine disabled" indicator is activated by the side stand switch and by the emergency switch on
the right side of the handlebar.- The LCD display gives a 5 digit indication for the total kilometres covered by the vehicle. It can be
expressed in kilometres or in miles: of course, this indication cannot be reset. To select the indication,
press "Trip" and "M" at the same time, then tirn the key switch to "ON"; keep these 2 buttons
pressed for more than 3" to display "SET" on the display, then the display switches from miles
to kilometres, or vice versa.
The instrument panel digital section is completed
by a liquid crystal display and 4 control buttons.
The display has 3 icons:- Oil
- Service
- Belt
- The "Oil" icon warns the user of the need of replacing the engine oil.
- The "Service" icon warns the user of the need of servicing the vehicle.
- The "Belt" icon warns the user of the need of replacing the driving belt.
After servicing by the authorised workshop, the icon message must be reset by the "Reset" button
located in the front side of the vehicle under the headlight upper cover. The "Reset" button allows
resetting the kilometres covered and, in the case of "OIL" and "BELT" and "SERVICE", also the year
count. This count remains active even if the battery is disconnected for a short time.
To reset one of the icons, press the "Reset" button for less than a second, then on the icon
before that to be reset press "Reset" for at least 3" so as to display:
- The selectionj of the desired icon through the relevant solid light.
- The flashing of this light confirms the reset.
- For example, to reset the "Service" icon, go to "Oil" and press the "Reset" button for at least 3". To
reset "Oil", repeat the above procedure going to "Belt".
This procedure must be repeated since the selection of the icon and its reset are operations to be made
at the same time (it is not possible to view the desired function and reset by two different button pres-
sures since in this way the next icon would be reset).
Data check function
The date must be adjusted upon the vehicle delivery to the customer. This is because the clock starts
counting the year for the Service function. If the clock has already been started, reset the functions
Electrical system X9 Evolution 500
ELE SYS - 66
-
8/6/2019 X9 500 Evo Workshop Manual
67/434
Oil, Service and Belt. The calendar is programmed from 2000 to 2050, to adjust the date and
time use the two buttons Clock and Set.
To guarantee the vehicle safety, every time the key switch is set to ON, all of the digital indications
are checked.The digital section also has a functional check of the 4 analogue instruments and of the flashing light
control. To start this check, keep buttons Clock and Set pressed and set the key switch to
ON. Within 4 seconds, the software version is displayed, the instruments indicate the scale bottom
and the direction indicators turn on.
At the end of the above procedure, there is the normal check of the indicator lights.
pics
PICS SECTIONSpecification Desc./Quantity
1 Display pics2 Intercom Controller3 Intercom connectors4 Battery 12V - 4Ah5 Fuse no. 13 30 A6 Key switch contacts7 Fuse no. 7 10A8 Fuse no. 12 7,5 A
X9 Evolution 500 Electrical system
ELE SYS - 67
-
8/6/2019 X9 500 Evo Workshop Manual
68/434
Captions
A = Satellite
D = Mobile phone cable
F = Telephone connectorH = Spark plug inspection port
J = Loudspeaker
L = Microphone
O = Headset clip
R = Volume button-
U = Passenger connection
X = Volume button +
B = Control unit
E = Control unit power supply connector
K = Vehicle control unit connector
M = MODE button
P = Satellite connector
S = Selection button
V = Pilot connection
Y = UP button
C = Mobile phone
G = Control unit audio connection cables
Electrical system X9 Evolution 500
ELE SYS - 68
-
8/6/2019 X9 500 Evo Workshop Manual
69/434
I = Headset cables
N = Loudspeaker
Q = Vehicle satellite connector
T = Cable support plateW = DOWN button
Z = Fixing of control unit to chassis
The control unit PICS X9 (B) combines in a single product the traditional function of intercom for motor-
riders and that of hadsfree kit for mobile phones and RDS radios.
The voice activation of the intercom function allows eliminating the ground noise caused by the wind It
can be enabled both in automatic and manual mode selecting the two available levels high/low.
Without passenger, the control unit can be used by the pilot as telephone handsfree and/or to listen to
the radio or to the external audio source.
The phone talk sets automatically to the pilot when the call signal is detected, but it can be switched to
the passenger and/or vice versa by the button (Y) located on the satellite.
The listening volume is adjusted by hand using buttons (R) and (X) for the two loudspeakers; this
adjustment affects the audio, intercom and telephone.
The control unit is provided with an auxiliary audio socket for a portable CD or cassette reader.
During the telephone conversation, the external source is disconnected from the conversation channel
and is restored at the end of the same.
The control unit is adapted to specific mobile phones by the telephone cable (D) (supplied separately).
N.B.
THE MOBILE PHONE-CONTROL UNIT INTERFACE CABLE IS AVAILABLE FOR MOST MOBILEPHONES AVAILABLE ON THE MARKET. CHECK THE AVAILABILITY OF THE INTERFACE CA-BLE FOR YOUR SPECIFIC MOBILE PHONE AT THE CONCESSIONAIRE'S.
The microphone stem is provided with an elastic
metal clip to fix it to the bottom edge of the helmet,
on the right side.
The loudspeaker (J) is fixed inside the helmet, atthe ear height, by an attachment velcro (N).
To optimise the intercom communication quality:
- For crash helmets, bend the microphone stem so
that the capsule is fully seated into the helmet, with
the white identification spot (see figure 2) facing
the mouth.
- For open helmets, bend the microphone stem so that the capsule sensitive part is as close as possible
to the mouth, using the white identification spot (see figure).WARNING
X9 Evolution 500 Electrical system
ELE SYS - 69
-
8/6/2019 X9 500 Evo Workshop Manual
70/434
DON'T REMOVE THE MICROPHONE CAPSULE PROTECTION.
Insert both headsets into the connectors; the pilot's is the front one, the passenger's is the rear one.
Move the ignition key to ON and the intercom will start automatically, at the low level (LOW); the intercom
can be started in manual mode too.
Adjust the volume using buttons (X) (R).
The voice activation level can be switched to two levels (high; low).
In automatic mode, the intercom starts automatically when the pilot or the passenger talk, and it remains
active for 20 seconds at the end of the talk (be careful to the level set).
To switch it to the high level (HIGH), press button (M) and then button (S) when the radio function is
displayed.
A mobile phone can be connected to the device using the special cable (D) (see Piaggio accessories);
when a call is received, a tone is heard by both the passenger and the pilot; after the tone, the call is
switched to the pilot, with the possibility of switching it to the passenger by button (Y). The call can be
temporarily interrupted by button (W) to switch to the intercom, and then resumed pressing the same
button.
In any case, when the call is received, the control unit emits a short sound on both loudspeakers,
optionally with the phone's tone, if the phone model has one.
When the vehicle is stopped, if a call is in progress the control unit remains on until the conversation is
ended.The mobile phone should be set to the automatic answer function to prevent having to press a key to
start the conversation.
For the models not provided with this function: you can select the answer by any key option.
The conversation volume can only be set by the mobile phone.
The volume should be set to maximum.
It is possible to connect a scatterer (2.5 W max) by the external scatterer socket (see figure 1). Besides
the radio, intercom and handsfree kit functions, it is possible to connect the control unit to a portable
CD reader or a walkman by a cable with stereo jack termination 3.5 mm. Adjust the external source
volume so that it can be heard corrctly without having to adjust the intercom volume.
During a conversation in intercom mode, the audio from the radio or from the external source remains
in background at a lower volume.
N.B.
ALWAYS REFER TO THE USE MANUAL OF YOUR MOBILE PHONE TO SET UP THE FUNCTIONSDESCRIBED ABOVE.
N.B.
THE USERS OF MOTOROLA 8700, STARTAC 130 CD920 CD930 AND BOSCH M-COM 506MUST CONNECT THEIR MOBILE TO THE CONTROL UNIT WITH PHONE OFF: THE PHONE WILLSWITCH ON AUTOMATICALLY.
Electrical system X9 Evolution 500
ELE SYS - 70
-
8/6/2019 X9 500 Evo Workshop Manual
71/434
STARTING (USING THE VEHICLE KEY)Specification Desc./Quantity
No helmet inserted - Logo X9 Tuner - source - Speakerphone with external speakersDriver headphone inserted - Driver/passenger helmet - pas-
senger crossed out
Tuner - source - Speakerphone
Passenger headphone inserted - Driver/passenger helmet -driver crossed out
Tuner - source - Speakerphone
Driver and passenger headphones inserted - Driver and pas-senger helmets
Tuner - source - Speakerphone - Intercom
N.B.
EVERY TIME THE KEY SWITCH IS SET TO "ON" THE PICS SYSTEM DISPLAY CHECKS ALLAVAILABLE ICONS.
TURNING ON/OFF THE DEVICE (VEHICLE RUNNING)Specification Desc./Quantity
Turn off - M > 4 sec.
Turn on - M > 4 sec.N.B.
WHEN THE VEHICLE IS STARTED, IF THE DEVICE HAD BEEN TURNED OFF THE ICON CHECKWILL BE DISPLAYED AND AT THE END OF THIS STEP IT WILL RETURN TO THE PREVIOUSPOSITION (OFF). TO RESTART, PRESS "M" FOR MORE THAN 4 SEC.
MANUAL INTERCOMSpecification Desc./Quantity
Activation - M two times ShortDeactivation - M two times Short
N.B.
AFTER MANUAL DISABLING, THE INTERCOM SWITCHES TO AUTOMATIC MODE WITH LESSSENSITIVE ENABLE LEVEL (LOW).
TUNER/SOURCESpecification Desc./Quantity
Radio on - S ShortRadio off - S Short
Source on - M go after S Short, > 2 sec.Source off -M go after S short, > 2 sec
Manual tuning UP - M go after Short, ContinuousManual tuning DOWN -M go after short, continuousAutomatic tuning UP - M go after Short, Continuous
Automatic tuning DOWN -M go after short, shortMemory scanning UP - ^ Short
Memory scanning DOWN - v ShortAUTOSTORE memorization - > 2 sec.
RDS - M go after vol + (AF - TA - PTY) Short, ShortPTY functions (can only be selected after enabling PTY) - Vol.
-Short
Manual station memorization - Select station* go after S** goafter ^ o V (select station) and after S (to confirm)
> 4 sec., short, short
* By automatic or manual tuning described above
** Press until the display flashes
N.B.
THE BUTTONS MUST BE PRESSED IN A SEQUENCE NOT AT THE SAME TIME.
RDS Radio Data System
X9 Evolution 500 Electrical system
ELE SYS - 71
-
8/6/2019 X9 500 Evo Workshop Manual
72/434
Several functions are provided but few of them are used correctly. Basic functions as the AF (alternative
frequencies), that allow listening to a fixed radio station on most of the territory during a journey, are
not always used properly. The same also applies to traffic news.
AF Alternative Frequencies
This allows the receiver to automatically tune on an alternative frequency stronger than the currently
listened by relating to the same station.
TA Traffic Announcement identification
When the traffic news are on air, the function starts and interrupts any other radio stations to listen to
the traffic news. You must be tuned on the station that transmits the news.
PTY Program Type
This allows identifying different types of music programs, to listen to the news, etc. There will be: News,
Affairs, Info, Sport ecc.
SPEAKERPHONE TELEPHONESpecification Desc./Quantity
Driver-passenger conversation passage - ShortIntercom-telephone passage - v Short
Volume adjustment
icon
Headphone inserted
icon
Passenger headphone
not inserted icon
Driver headphone not
inserted icon
Electrical system X9 Evolution 500
ELE SYS - 72
-
8/6/2019 X9 500 Evo Workshop Manual
73/434
Intercom on icon
Manual intercom icon
Incoming call icon
Incoming call icon only
with driver headphone
inserted.
Incoming call icon onlywith passenger head-
phone inserted.
Telephone call with
driver icon
Telephone call with
passenger icon
Telephone conversation intercom icon
SPECIFICHETECNICHE
Specification Desc./Quantity
1 Power 10.5V 16V1.4 A max
X9 Evolution 500 Electrical system
ELE SYS - 73
-
8/6/2019 X9 500 Evo Workshop Manual
74/434
Specification Desc./Quantity
2 Key 10.5V 16V1.5 mA max
3 Maximum output power 500 mW per channel4 Power consumption vehicle off ~0 mA
in stand-by ~280 mA
at maximum power ~500 mA5 Frequency response audio 200 Hz - 20 kHz 3 dB
intercom 200 Hz - 5 kHz 3 dB6 Microphones -69 dB 3 dB one-way7 Frequency response: audio 200 Hz 20 kHz 3 dB8 Loudspeakers 8 - 0.5 m
Sealed battery
Airtight battery start-up operations
If the vehicle is provided with an airtight battery, the only maintenance required is the check of its charge
and recharging, if needed.
These operations should be carried out before delivering the vehicle, and on a six-month basis for
storage with open circuit.
Besides upon pre-delivery it is therefore necessary to check the battery charge and recharge it, if re-
quired, before storing the vehicle and afterwards every six months.
INSTRUCTIONS FOR THE RENEWAL RECHARGE AFTER OPEN-CIRCUIT STORAGE
1) Voltage check
Before installing the battery on the vehicle, perform an open-circuit voltage check using a conventional
tester.
- If voltage exceeds 12.60 V, the battery may be installed without any renewal recharge.
- If voltage is below 12.60 V, a renewal recharge is required as explained at 2).
2) Constant-voltage battery instructions
- Constant voltage charge equal to 14.40-14.70V
- Initial charge current equal to 0.3-0.5 x rated capacity
- Charge time:
- Recommended 10-12
- Minimum 6 h
- Maximum 24 hConstant-current battery instructions
- Charge current equal to 1/10 o