X-ray Inspection System - Factronics USA · X-ray Inspection System 6 Specifications Model...
20
X-ray Inspection System KD74 KD74-h KD74-f DualX For Specific Applications October 2015
Transcript of X-ray Inspection System - Factronics USA · X-ray Inspection System 6 Specifications Model...
X-ray Inspection System
KD74
KD74-h
KD74-f
DualX
For Specific Applications
October 2015
X-ray Inspection System
Product Catalog
L i n e u p
Standard
KD74 series
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ●Size variations
Highly versatile system with a proven track record suits a wide range of packaged products.
Simultaneous inspection including shape analysis, missing item and package integrity inspection
are available.
Entry
KD74-f series
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ●Size variations
With low X-ray output and simple construction, this series are suitable for dry products.
DualX
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ● High power ● Low power
Analyzing two different x-ray energy signals, it clearly distinguishes contaminants from products.
Performs accurate inspection of low density bones in meat and overlapping products.
For Specific Applications
●Large bags and cartons ●Tall products
●Sanitary design ●Pipe type
X-ray systems in a variety of configurations offered to fit specific inspection requirements.
High Definition
KD74-h series
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ●For metal particles ●For low density contaminants ●Size variations
High accuracy detection technology detects a 0.2 diameter metal sphere. Suitable for soft
contaminants that are of low-density, such as bone and plastics, as well as for minute metal
particles.
2
X-ray Inspection System
Product Catalog
L i n e u p
Standard
KD74 series
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ●Size variations
Highly versatile system with a proven track record suits a wide range of packaged products.
Simultaneous inspection including shape analysis, missing item and package integrity inspection
are available.
Entry
KD74-f series
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ●Size variations
With low X-ray output and simple construction, this series are suitable for dry products.
DualX
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ● High power ● Low power
Analyzing two different x-ray energy signals, it clearly distinguishes contaminants from products.
Performs accurate inspection of low density bones in meat and overlapping products.
For Specific Applications
●Large bags and cartons ●Tall products
●Sanitary design ●Pipe type
X-ray systems in a variety of configurations offered to fit specific inspection requirements.
High Definition
KD74-h series
Products Dry products Wet products
Protection class IP40 IP66
X-ray output Low (max. 100W) Middle to High (max. 210W) High (max. 350W)
Product range ●For metal particles ●For low density contaminants ●Size variations
High accuracy detection technology detects a 0.2 diameter metal sphere. Suitable for soft
contaminants that are of low-density, such as bone and plastics, as well as for minute metal
particles.
Note: Any one of the pass heights can be selected.
Model Detection area (Units：mm) Page
KD7405AWH/ADWH /BWH/BDWH W2 (160)
W1 (240)
H (1
20)
Effective detection width = 240 – 80×Hp
120
Effective detection height = 120×(240–Wp)80
4
KD7405CWT/DWTKD7405DWH 8, 9
KD7405KP/KDP 10
KD7405ABWHW2 (200)
W1 (240)
H(50
)
Effective detection width = 240 – 40×Hp
50
Effective detection height = 50×(240–Wp)40
6
KD7405ACWH 7
KD7405KCP 10
KD7416AWH/ADWH /BWH/BDWH W2 (280)
W1 (390)
H (1
50)
Effective detection width = 390 – 110×Hp
150
Effective detection height = 150×(390–Wp)110
5
KD7416DWH 9
KD7416AWZE/ADWZEKD7416DWZ 11, 12
KD7416ABWH
W2 (355)
W1 (390)H (50)
Effective detection width = 390 – 35×Hp50
Effective detection height = 50×(390–Wp)35
6
KD7416ACWH 7
KD7416ACWZE 11
KD7417BWHW2 (230)
W1 (390)
H (2
20)
Effective detection width = 390 – 160×Hp
220
Effective detection height = 220×(390–Wp)160
5
KD7417DWH9
KD7447DWKD7447DWEKD7447FWE
W2 (410)
W1 (590)
H (2
50)
Effective detection width = 590 – 180×Hp
250
Effective detection height = 250×(590–Wp)180
13
KD7337AWH1KD7337AWH2 W2 (510)
W1 (690)
H (2
50)
Effective detection width = 690 – 180×Hp
250
Effective detection height = 250×(690–Wp)180
14
KD7416AMW2 (255)
W1 (365)
H (1
50)
Effective detection width = 365 – 110×Hp
150
Effective detection height = 150×(365–Wp)110
15
KD7416ACM
W2 (330)
W1 (365)H (50)
Effective detection width = 365 – 35×Hp50
Effective detection height = 50×(365–Wp)35
15
KD7478AWHKD7478BWH W (150)
H1
(307
)
H2
(237
) Effective detection width= 150×(307–Hp)70
Effective detection height= 307– 70×Wp150
16
Model Selection List
Products
3
● When Hp ≦ 237: Effective detection width = 150
● When 237 < Hp ≦ 307:
X-ray Inspection System
4
■ SpecificationsModel KD7405AWH KD7405ADWH KD7405BWH KD7405BDWHDetection sensitivity 1 Fe sphere and SUS sphere 0.3 mm dia., SUS wire 0.2 mm dia.× 2 mm longX-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 W Tube voltage 25 to 80 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2 Maximum width 240 mm, maximum height 120 mm (see drawing for detection area)Belt width 270 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100
Belt speed 3
Maximum product weight 4
5 to 60 m/min, maximum 5 O61 to 90 m/min, maximum 2 O5 to 40 m/min, maximum 10 O (optional)
Power requirements 5, 6, 7 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 210 O 215 O 220 O 225 OEnvironmental conditions 8 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The entrance and exit may require covers depending on the length of a product. 3: Variable depending on Product No. 4: Sum total of product weight on the conveyor. 5: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 6: Allowable power fluctuation range is ± 10%. 7: Installing the air-conditioner option changes the displayed power consumption. 8: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 77 dB(A).
External Dimensions
240
590 t
o 6
90
196
(80º)
7304
65
265
1360 t
o 1
460
270
Belt w
idth
33.5 dia.
Roller
60 dia.
450
Leg spacing 605
Leg spacing
240
Effective detection width
700 t
o 8
00
Lin
e h
eig
hts
120
Pass h
eig
ht
800/※1000
500
120
240
160
Detection area
Units:mm
KD7405AWH KD7405ADWH ※KD7405BWH KD7405BDWH ※
StandardKD74 series
KD7405AWH/ADWH/BWH/BDWH Maximum width Maximum height
Product size: 240 mm × 120 mm
KD7405AWH
Enter the curtain in stable position
Become unstable at the joint
Become unstable by the curtain
Pass over the joint in stable position
KD7405ADWH / KD7405BDWH
The conveyor is lengthened from 800 to 1000 for smooth product transfer.
For Packaged Products
KD
74 seriesK
D74-h series
KD
74-f seriesFor Specific Applications
DualX
X-ray Inspection System
5
■ SpecificationsModel KD7416AWH KD7416ADWH KD7416BWH KD7416BDWH KD7417BWHDetection sensitivity 1 Fe sphere and SUS sphere 0.3 mm dia., SUS wire 0.2 mm dia.× 2 mm long
X-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 W Tube voltage 25 to 80 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 W
Safety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)
Product size 2, 3 Maximum width 390 mm, maximum height 150 mm Maximum width 390 mm, maximum height 220 mm
Belt width 420 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 4
Maximum product weight 55 to 60 m/min, maximum 5 O 5 to 40 m/min, maximum 10 O5 to 40 m/min, maximum 10 O (optional) ー
Power requirements 6, 7, 8 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 255 O 260 O 265 O 270 O 265 OEnvironmental conditions 9 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The detection area is shown above. 3: The entrance and exit may require covers depending on the length of a product. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 7: Allowable power fluctuation range is ± 10%. 8: Installing the air-conditioner option changes the displayed power consumption. 9: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 77 dB(A).
External Dimensions150
390
280
Detection area
880
540
340
420
Belt w
idth
1530 t
o 1
630
33.5 dia.
Roller
60 dia.
450
Leg spacing
700 t
o 8
00
Lin
e h
eig
hts
800/※1000
500
(280)
271
(80º)
755
Leg spacing
390
Effective detection width
150
Pass h
eig
ht
600
to 7
00
Units:mm
KD7416AWH KD7416ADWH ※KD7416BWH KD7416BDWH ※
220
390
230
Detection area
880
540
340
420
Belt
wid
th
1530
to 1
630
33.5 dia.Roller
60 dia.450
Leg spacing
700
to 8
00Li
ne h
eigh
ts
800
500
(345)271
(80º)
755Leg spacing
390Effective detection width
220
Pas
s he
ight
610
to 7
10
Units:mm
KD7417BWH
StandardKD74 series
KD7416AWH
For Packaged Products
KD
74 seriesK
D74-h series
KD
74-f seriesFor Specific Applications
DualX
KD7416AWH/ADWH/BWH/BDWH Maximum width Maximum height
Product size: 390 mm × 150 mm
KD7417BWH Maximum width Maximum height
Product size: 390 mm × 220 mm
X-ray Inspection System
6
■ SpecificationsModel KD7405ABWH KD7416ABWHDetection sensitivity 1 Fe sphere and SUS sphere 0.3 mm dia., SUS wire 0.2 mm dia.× 2 mm longX-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2, 3 Maximum width 240 mm, maximum height 50 mm Maximum width 390 mm, maximum height 50 mmBelt width 270 mm 420 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 4
Maximum product weight 55 to 50 m/min, maximum 5 O5 to 40 m/min, maximum 10 O (optional)
Power requirements 6, 7, 8 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 230 O 280 OEnvironmental conditions 9 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The detection area is shown above. 3: The entrance and exit may require covers depending on the length of a product. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 7: Allowable power fluctuation range is ± 10%. 8: Installing the air-conditioner option changes the displayed power consumption. 9: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 77 dB(A).
External Dimensions
50
200
※355
73
0
※8
804
65
※5
40
26
5
※3
402
32
※3
82
240
※390
Detection area
27
0/※
42
0
Be
lt w
idth
132
1430
1360
1000
435
33.5 dia.
Roller
Hopper
Interlock
91
5 t
o 1
01
5※
95
5 t
o 1
05
5
13
60
to
14
60
※1
53
0 t
o 1
63
0
70
0 t
o 8
00
Lin
e h
eig
hts
65
0 t
o 7
50
60 dia.
450
Leg spacing 605/※755
Leg spacing
196
※271
50
Pa
ss h
eig
ht
240/※390
Effective detection width
Units:mm
KD7405ABWH KD7416ABWH ※
StandardKD74 series
KD7405ABWH
Enter the curtain in stable position
Become unstable at the joint
Become unstable by the curtain
Pass over the joint in stable position
KD7405ADWH / KD7405BDWH
A shield plate and a x-ray leakage prevention cover prevent x-ray leakage.
For Bulk Flow of Unpacked Fresh Food
KD
74 seriesK
D74-h series
KD
74-f seriesFor Specific Applications
DualX
KD7405ABWH Maximum width Maximum height
Product size: 240 mm × 50 mm
KD7416ABWH Maximum width Maximum height
Product size: 390 mm × 50 mm
X-ray Inspection System
7
■ SpecificationsModel KD7405ACWH KD7416ACWHDetection sensitivity 1 Fe sphere and SUS sphere 0.3 mm dia., SUS wire 0.2 mm dia.× 2 mm longX-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2, 3 Maximum width 240 mm, maximum height 50 mm Maximum width 390 mm, maximum height 50 mmBelt width 270 mm 420 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 4
Maximum product weight 55 to 50 m/min, maximum 5 O5 to 40 m/min, maximum 10 O (optional)
Power requirements 6, 7, 8 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 230 O 285 OEnvironmental conditions 9 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The detection area is shown above. 3: The entrance and exit may require covers depending on the length of a product. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 7: Allowable power fluctuation range is ± 10%. 8: Installing the air-conditioner option changes the displayed power consumption. 9: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 77 dB(A).
External Dimensions
Detection area
50
200
※355
240
※390
73
0
※8
804
65
※5
40
26
5
※3
40
27
0/※
42
0
Be
lt w
idth
500
1268
1340 to 1355
14
20
to
15
50
※1
59
0 t
o 1
72
0
76
0 t
o 8
90
605/※755
Leg spacing
196
※271
240/※390
Effective detection width
70
0 t
o 8
00
Lin
e h
eig
hts
60 dia.450
Leg spacing
10 to
15º 3
0 t
o 5
0
Pa
ss h
eig
ht
Units:mm
KD7405ACWH KD7416ACWH ※
StandardKD74 series
KD7405ACWH
Enter the curtain in stable position
Become unstable at the joint
Become unstable by the curtain
Pass over the joint in stable position
KD7405ADWH / KD7405BDWH
Instead of x-ray protection curtains that could disrupt product flow, an inclined conveyor with covers is equipped for stable conveyance.
For Lightweight Products and Those in Small Bags
KD
74 seriesK
D74-h series
KD
74-f seriesFor Specific Applications
DualX
KD7405ACWH Maximum width Maximum height
Product size: 240 mm × 50 mm
KD7416ACWH Maximum width Maximum height
Product size: 390 mm × 50 mm
X-ray Inspection System
8
■ SpecificationsModel KD7405CWT KD7405DWTDetection sensitivity 1 Fe sphere and SUS sphere 0.2 mm dia. 2, SUS wire 0.2 mm dia.× 2 mm longX-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 300 W Tube voltage 25 to 80 kV, tube current 0.3 to 10.0 mA, output 7.5 to 350 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 3 Maximum width 240 mm, maximum height 120 mm (see drawing for detection area)Belt width 270 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100
Belt speed 4
Maximum product weight 5
10 to 60 m/min, maximum 5 O61 to 90 m/min, maximum 2 O5 to 40 m/min, maximum 10 O (optional)
Power requirements 6, 7, 8 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 230 OEnvironmental conditions 9 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: Reference value using Anritsu test piece. 3: The entrance and exit may require covers depending on the length of a product. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 7: Allowable power fluctuation range is ± 10%. 8: Installing the air-conditioner option changes the displayed power consumption. 9: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 77 dB(A).
External Dimensions120
240
160
Detection area
270
Belt w
idth
730
265
465
33.5 dia.
Roller
605
Leg spacing
450
Leg spacing
196
240
Effective detection width
(240)
120
Pass h
eig
ht
(80º)
700 t
o 8
00
Lin
e h
eig
hts 1360 t
o 1
460
500
800
590 t
o 6
90
60 dia.
Units:mm
KD7405CWTKD7405DWT
High DefinitionKD74-h series
KD7405DWT
For Packaged Products
KD
74-h seriesK
D74 series
KD
74-f seriesFor Specific Applications
DualX
KD7405CWT/DWT Maximum width Maximum height
Product size: 240 mm × 120 mm
X-ray Inspection System
9
External Dimensions120
240
160
Detection area
270
Belt w
idth
730
265
465
33.5 dia.
Roller
605
Leg spacing
450
Leg spacing
196
240
Effective detection width
(240)
120
Pass h
eig
ht
(80º)
700 t
o 8
00
Lin
e h
eig
hts 1360 t
o 1
460
500
800
590 t
o 6
90
60 dia.
KD7405DWH
(80º)
420
Belt w
idth
33.5 dia.
Roller
60 dia.
450
Leg spacing 755
Leg spacing
(280)
※(345)
390
Effective detection width
700 to 8
00
Lin
e h
eig
hts 1
530 to 1
630
880
540
340
150/※
220
Pass h
eig
ht
150
※220
280
※230
271
500
800
390
Detection area
600 to 7
00
※610 to 7
10
KD7416DWH KD7417DWH ※
Units:mmUnits:mm
■ SpecificationsModel KD7405DWH KD7416DWH KD7417DWHDetection sensitivity 1 Fe sphere and SUS sphere 0.3 mm dia., SUS wire 0.2 mm dia.× 2 mm longX-ray output Tube voltage 25 to 80 kV, tube current 0.3 to 10.0 mA, output 7.5 to 350 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2, 3 Maximum width 240 mm, maximum height 120 mm Maximum width 390 mm, maximum height 150 mm Maximum width 390 mm, maximum height 220 mmBelt width 270 mm 420 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100
Belt speed 4
Maximum product weight 5
10 to 60 m/min, maximum 5 O 5 to 60 m/min, maximum 5 O 5 to 40 m/min, maximum 10 O61 to 90 m/min, maximum 2 O 5 to 40 m/min, maximum 10 O (optional) ー5 to 40 m/min, maximum 10 O (optional) ー ー
Power requirements 6, 7, 8 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 230 O 280 OEnvironmental conditions 9 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The detection area is shown above. 3: The entrance and exit may require covers depending on the length of a product. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 7: Allowable power fluctuation range is ± 10%. 8: Installing the air-conditioner option changes the displayed power consumption. 9: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 77 dB(A).
High DefinitionKD74-h series
KD7416DWH
For Packaged Products
KD
74-h seriesK
D74 series
KD
74-f seriesFor Specific Applications
DualX
KD7405DWH Maximum width Maximum height
Product size: 240 mm × 120 mm
KD7416DWH Maximum width Maximum height
Product size: 390 mm × 150 mm
KD7417DWH Maximum width Maximum height
Product size: 390 mm × 220 mm
X-ray Inspection System
10
■ SpecificationsModel KD7405KP KD7405KDP KD7405KCPDetection sensitivity 1 Fe sphere and SUS sphere 0.3 mm dia., SUS wire 0.2 mm dia.× 2 mm longX-ray output Tube voltage 25 to 50 kV, tube current 0.3 to 4.0 mA, output 7.5 to 100 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2, 3 Maximum width 240 mm, maximum height 120 mm Maximum width 240 mm, maximum height 50 mmBelt width 270 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100
Belt speed 4
Maximum product weight 5
5 to 60 m/min, maximum 3 O 5 to 50 m/min, maximum 3 O61 to 80 m/min, maximum 2 O 5 to 35 m/min, maximum 6 O (optional)5 to 35 m/min, maximum 6 O (optional) ー
Power requirements 6, 7, 8 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 700 VA, rush current 80 A (typ.) (5 ms or less)Mass 200 O 205 O 220 OEnvironmental conditions 9 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The detection area is shown above. 3: The entrance and exit may require covers depending on the length of a product. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 7: Allowable power fluctuation range is ± 10%. 8: Installing the air-conditioner option changes the displayed power consumption. 9: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 72 dB(A).
External Dimensions120
240
160
Detection area
270
Belt w
idth
(470)
（425
）
465
715
250
(195º)
(175º)
60 dia.
450
Leg spacing
605
Leg spacing
33.5 dia.
Roller
700 t
o 8
00
Lin
e h
eig
hts
500
195
710
800/※1000
120
Pass h
eig
ht
(90º)
1360 t
o 1
460
580 t
o 6
80 (240)
240
Effective detection width
Units:mm
KD7405KPKD7405KDP ※
(175º)
(265)
195
(90º)
(425)
250
504
65
715
270
Belt w
idth
33.5 dia.
Roller
60 dia.
450
Leg spacing 605
Leg spacing
240
Effective detection width
(195º)
(470)
1340 to 1355
10 to
15º
760 t
o 8
90
610 t
o 7
401420 t
o 1
550
700 t
o 8
00
Lin
e h
eig
hts
30 t
o 5
0
Pass h
eig
ht
1268
500
240
200
Detection area
Units:mm
KD7405KCP
EntryKD74-f series
KD7405KP
For Packaged Products
KD
74-f seriesK
D74 series
KD
74-h seriesFor Specific Applications
DualX
KD7405KP/KDP Maximum width Maximum height
Product size: 240 mm × 120 mm
KD7405KCP Maximum width Maximum height
Product size: 240 mm × 50 mm
For Lightweight Products and Those in Small Bags
X-ray Inspection System
11
External Dimensions150
390
280
Detection area
880
540
340
420
Belt w
idth
1530 t
o 1
630
33.5 dia.
Roller
60 dia.
450
Leg spacing
700 t
o 8
00
Lin
e h
eig
hts
800/※1000
500
(280)
271
(80º)
755
Leg spacing
390
Effective detection width
150
Pass h
eig
ht
600
to 7
00
Units:mm
KD7416AWZEKD7416ADWZE ※
Detection area
50
355
390
88
0
54
03
40
42
0
Be
lt w
idth
500
1268
1340 to 1355
15
90
to
17
20
76
0 t
o 8
90
755
Leg spacing
271
390
Effective detection width
70
0 t
o 8
00
Lin
e h
eig
hts
60 dia.450
Leg spacing
10 to
15º 3
0 t
o 5
0
Pa
ss h
eig
ht
Units:mm
KD7416ACWZE
DualXKD74 series
KD7416AWZE
For Packaged Products
KD
74 seriesK
D74-h series
KD
74-f seriesD
ualXFor Specific Applications
■ SpecificationsModel KD7416AWZE KD7416ADWZE KD7416ACWZEX-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 1, 2 Maximum width 390 mm, maximum height 150 mm Maximum width 390 mm, maximum height 50 mmBelt width 420 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 3
Maximum product weight 410 to 60 m/min, maximum 5 O 10 to 50 m/min, maximum 5 O10 to 40 m/min, maximum 10 O (optional) 10 to 40 m/min, maximum 10 O (optional)
Power requirements 5, 6, 7 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 255 O 260 O 285 OEnvironmental conditions 8 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: The detection area is shown above. 2: The entrance and exit may require covers depending on the length of a product. 3: Variable depending on Product No. 4: Sum total of product weight on the conveyor. 5: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 6: Allowable power fluctuation range is ± 10%. 7: Installing the air-conditioner option changes the displayed power consumption. 8: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems does not exceed 70 dB(A).
KD7416AWZE/ADWZE Maximum width Maximum height
Product size: 390 mm × 150 mm
KD7416ACWZE Maximum width Maximum height
Product size: 390 mm × 50 mm
For Lightweight Products and Those in Small Bags
X-ray Inspection System
12
For Specific ApplicationsK
D74 series
KD
74-h seriesK
D74-f series
DualX
■ SpecificationsModel KD7416DWZX-ray output Tube voltage 25 to 80 kV, tube current 0.4 to 10.0 mA, output 10 to 350 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesSafety 15-inch color TFT LCD (unified image monitoring screen and operation screen)Display Touch panel (with touch buzzer)Product size 1 Maximum width 390 mm, maximum height 150 mm (see drawing for detection area)Belt width 420 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 2
Maximum product weight 35 to 60 m/min, maximum 5 O5 to 40 m/min, maximum 10 O (optional)
Power requirements 4, 5, 6 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 280 OEnvironmental conditions 7 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: The entrance and exit may require covers depending on the length of a product. 2: Variable depending on Product No. 3: Sum total of product weight on the conveyor. 4: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 5: Allowable power fluctuation range is ± 10%. 6: Installing the air-conditioner option changes the displayed power consumption. 7: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems is 77 dB(A).
External Dimensions15
0
390
280
Detection area
880
540
340
420
Belt
wid
th15
30 to
163
0
33.5 dia.Roller
60 dia.450
Leg spacing
700
to 8
00Li
ne h
eigh
ts
800500
(280)271
(80º)
755Leg spacing
390Effective detection width
150
Pas
s he
ight
600
to 7
00
Units:mm
KD7416DWZ
DualXKD74 series
KD7416DWZ
For Packaged ProductsKD7416DWZ Maximum width Maximum height
Product size: 390 mm × 150 mm
X-ray Inspection System
13
External Dimensions
690
111
4
424
1200
500
700 t
o 8
00
Lin
e h
eig
hts
49.5 dia.
Roller
836
Leg spacing
975
Leg spacing
80 dia.
350
590
Effective detection width
1806 t
o 1
906
250
Pass h
eig
ht
(484)
(471)
620
Belt w
idth
590
410
250
Detection area
Units:mm
KD7447DWKD7447DWE
620
300
690
463
1153
(471)
(800)
1200
Maintenancespace
Maintenancespace
49.5 dia.
Roller
700 to 8
00
82580 dia.
250
590
388
1906 to 2
006
(1500)
Belt w
idth
Lin
e h
eig
hts
Leg spacing
1013
Leg spacing
Pass h
eig
ht
Effective detection width
500
590
410
250
Detection area
Units:mm
KD7447FWE
■ SpecificationsModel KD7447DW KD7447DWE KD7447FWEDetection sensitivity 1 Fe sphere and SUS sphere 0.4 mm dia. Fe sphere and SUS sphere 0.5 mm dia. Fe sphere and SUS sphere 0.8 mm dia.X-ray output Tube voltage 25 to 80 kV, tube current 0.3 to 10.0 mA, output 7.5 to 350 W Tube voltage 80 to 100 kV, tube current 0.5 to 4.3 mA, output 40 to 350 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2, 3 Maximum width 590 mm, maximum height 250 mm (see drawing for detection area)Belt width 620 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100
Belt speed 4
Maximum product weight 5
10 to 35 m/min, maximum 50 O 10 to 35 m/min, maximum 50 O 7
36 to 40 m/min, maximum 30 O 6 36 to 40 m/min, maximum 30 O 7
25 to 50 m/min, maximum 20 O (optional) 25 to 50 m/min, maximum 20 O (optional) 7
Power requirements 8, 9, 10 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)
200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)
Mass 450 O 650 OEnvironmental conditions 11 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The entrance and exit may require covers depending on the length of a product. 3: Pass height of 350 mm is available as an option. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: In an environment where water or oil regularly splashes the equipment, the maximum is 20 O. 7: Can decrease if the conveyor is exposed to water or oil. 8: Allowable power fluctuation range is ± 10%. 9: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 10: Installing the air-conditioner option changes the displayed power consumption. 11: The air-conditioner option may be required depending on the operating environment. Note: The noise level of KD7447DW/KD7447DWE does not exceed 70 dB(A). The noise level of KD7447FWE is 72 dB (A).
For Specific Applications Large Products and CartonsKD74 series
KD7447DW
For Packaged Products
For Specific ApplicationsK
D74 series
KD
74-h seriesK
D74-f series
DualX
KD7447DW/DWE/FWE Maximum width Maximum height
Product size: 590 mm × 250 mm
X-ray Inspection System
14
For Specific ApplicationsK
D74 series
KD
74-h seriesK
D74-f series
DualX
■ SpecificationsModel KD7337AWH1 KD7337AWH2Detection sensitivity 1 Fe sphere and SUS sphere 0.5 mm dia.X-ray output Tube voltage 30 to 80 kV, tube current 0.3 to 7.0 mA, output 9.0 to 350 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2 Maximum width 690 mm, maximum height 250 mm (see drawing for detection area)Belt width 780 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 3
Maximum product weight 410 to 30 m/min, maximum 50 O31 to 35 m/min, maximum 40 O
Power requirements 5 200 Vac, single phase, 50/60 Hz, 1.8 kVA, D class grounding Mass 750 OEnvironmental conditions Temperature: 0º to 35ºC, relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP52Exterior Stainless steel (SUS304)Cooling system Air conditioner (standard equipped)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The entrance and exit may require covers depending on the length of a product. 3: Variable depending on Product No. 4: Sum total of product weight on the conveyor. 5: Allowable power fluctuation range is ± 10%. Note: The noise level of x-ray inspection systems is 72 dB(A).
External Dimensions250
1300
810
490
690
510
Detection area
780
Belt w
idth
1800
700
800
Leg spacing
80 dia.
450 to 5
50
Line
hei
ghts
250
Pass h
eig
ht
690
Effective detection width
1140
Leg spacing
410
Air conditioner
79 dia.
Roller
1695 to 1
795
2150 to 2
250
Units:mm
KD7337AWH1KD7337AWH2
For Specific Applications Large Products and CartonsKD73 series
KD7337AWH1Air conditioner is equipped as standard.
For Packaged ProductsKD7337AWH1/AWH2 Maximum width Maximum height
Product size: 690 mm × 250 mm
X-ray Inspection System
15
■ SpecificationsModel KD7416AM KD7416ACMDetection sensitivity 1 Fe sphere and SUS sphere 0.3 mm dia., SUS wire 0.2 mm dia.× 2 mm longX-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2, 3 Maximum width 365 mm, maximum height 150 mm Maximum width 365 mm, maximum height 50 mmBelt width 420 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 4
Maximum product weight 55 to 40 m/min, maximum 5 O 5 to 50 m/min, maximum 3 O5 to 35 m/min, maximum 10 O (optional) 5 to 35 m/min, maximum 8 O (optional)
Power requirements 6, 7 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.6 kVA, rush current 80 A (typ.) (5 ms or less)Mass 335 O 355 OEnvironmental conditions Temperature: 0º to 35ºC, relative humidity: 30% to 85%, non-condensingProtection class 8 IP69K (with all protection covers closed)Exterior Stainless steel (SUS304)Cooling system Air conditioner (standard equipped)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The detection area is shown above. 3: The entrance and exit may require covers depending on the length of a product. 4: Variable depending on Product No. 5: Sum total of product weight on the conveyor. 6: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 7: Allowable power fluctuation range is ± 10%. 8: Excluding air-conditioner ventilation hole. Note: The noise level of x-ray inspection systems is 82 dB(A).
External Dimensions
(610)
(420)
(410) 270
(365)
(380)
420
Belt w
idth
60 dia.
450
Leg spacing 755
Leg spacing
365
Effective detection width
(590)
(550 t
o 6
10)1540 t
o 1
600
1430
1380
480
900
540
360
720 t
o 7
80
Lin
e h
eig
hts
33.5 dia.
Roller
33.5 dia.
Roller
800
500
150
Pass h
eig
ht
(90º
)
(200
º)
(105º)
(140º)
Air conditioner
150
365
255
Detection area
Units:mm
KD7416AM
(610)
(185)
(170)
(36
5)
(38
0)
42
0
Belt
wid
th
60 dia.
450
Leg spacing
(410) 270
755
Leg spacing
365
Effective detection width
(59
0)
61
0 t
o 7
00
78
0 t
o 8
70 16
00
to
16
90
14
30
13
80
48
09
00
54
03
60
72
0 t
o 7
80
Lin
e h
eig
hts
33.5 dia.
Roller
48 dia.
Roller
500
1270
1360 to 1375
1340 to 1355
30
to
50
Pa
ss h
eig
ht
（90
°）
120°
(200
º)
(105º)
(125º)
10 to
15º
Air conditioner
Detection area
50
330
365
Units:mm
KD7416ACM
For Specific Applications Sanitary DesignKD74 series
KD7416ACMAir conditioner is equipped as standard.
For Specific ApplicationsK
D74 series
KD
74-h seriesK
D74-f series
DualX
KD7416AM Maximum width Maximum height
Product size: 365 mm × 150 mm
KD7416ACM Maximum width Maximum height
Product size: 365 mm × 50 mm
For Packaged Products
For Unpackaged Fresh Meat, Poultry and Fish
KD7416ADM (1000-mm long) and KD7416ABM (Hopper loading system) are also available. Contact our sales representatives for details.
X-ray Inspection System
16
KD
74 seriesK
D74-h series
KD
74-f seriesFor Specific Applications
DualX
■ SpecificationsModel KD7478AWH KD7478BWHDetection sensitivity 1 Fe sphere and SUS sphere 0.4 mm dia.X-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 W Tube voltage 25 to 80 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product size 2 Maximum width 120 mm, maximum height 350 mm (see drawing for detection area)Belt width 120 mmMasking function Equipped as standardMissing product detection function Equipped as standardClip check function Equipped as standardPreset memory Maximum 100Belt speed 3
Maximum product weight 4 5 to 60 m/min, maximum 5 O
Power requirements 5, 6, 7 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.0 kVA, rush current 80 A (typ.) (5 ms or less)Mass 310 O 315 OEnvironmental conditions 8 Temperature: 0º to 35ºC (0º to 40ºC with optional air conditioner), relative humidity: 30% to 85%, non-condensingProtection class Conveyor IP66, other parts IP40, tool free belt removalExterior Stainless steel (SUS304)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: The entrance and exit may require covers depending on the length of a product. 3: Variable depending on Product No. 4: Sum total of product weight on the conveyor. 5: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. 6: Allowable power fluctuation range is ± 10%. 7: Installing the air-conditioner option changes the displayed power consumption. 8: The air-conditioner option may be required depending on the operating environment. Note: The noise level of x-ray inspection systems does not exceed 70 dB(A).
External Dimensions
55
90
5
52
03
85
1455
1400
500
12
0
Be
lt w
idth
35
0
Pass
heig
ht
712
Leg spacing
382
150
Effective detection width
60 dia.
450
Leg spacing
70
0 t
o 8
00
Lin
e h
eig
hts
15
05
to
16
05
33.5 dia.
Roller
IN OUT
150
30
7
23
7
Detection area
Units:mm
KD7478AWHKD7478BWH
Flow direction can be changed.
For Specific Applications Tall ProductsKD74 series
KD7478AWH
For Packaged ProductsKD7478AWH/BWH Maximum width Maximum height
Product size: 120 mm × 350 mm
Note: Not usable for glass containers.
17
X-ray Inspection System
■ SpecificationsModel KD7483AFWHDetection sensitivity 1 Fe sphere and SUS sphere 0.6 mm dia. (when only water is conveyed)X-ray output Tube voltage 25 to 60 kV, tube current 0.3 to 7.0 mA, output 7.5 to 210 WSafety X-ray leakage maximum 1μSv/h or less, prevention of x-ray leakage by safety devicesDisplay 15-inch color TFT LCD (unified image monitoring screen and operation screen)Operation method Touch panel (with touch buzzer)Product sizeProduct: solids in fluid 12 mm or smaller (less than 1/3 of the minimum height of the inspection section)
Transfer pipe dimension 3-inch (76.2 mm) dia.Inspection section pass height 35 mm (fixed)Position change at sensitivity adjustment Main unit position change (pipe position fixed)Preset memory Maximum 100Processing capacity (flow) 11.0 S/hPower requirements 2, 3 100 to 120 or 200 to 240 Vac, single phase, 50/60 Hz, 1.6 kVA, rush current 80 A (typ.) (5 ms or less)Mass 340 OEnvironmental conditions Temperature: 0º to 40ºC, relative humidity: 30% to 85%, non-condensingProtection class Product transfer pipe IP66, other parts IP40Exterior Stainless steel (SUS304)Cooling system Air conditioner (standard equipped)
1: Actual sensitivity depends on the physical properties of products (contents and shape) and on the environmental conditions. 2: Allowable power fluctuation range is ± 10%. 3: Selectable by switching terminals. Note that the rush current shown above is at an AC voltage of 200 V. It varies according to voltage. Note: The noise level of x-ray inspection systems is 71 dB(A).
External Dimensions
(170º)
(170º)
88
0 t
o 9
80
Lin
e h
eig
hts
99
0 t
o 1
09
0
Jo
int
he
igh
ts
77
0 t
o 8
70
Jo
int
he
igh
ts
560
Leg spacing
1280
Leg spacing
Clamp Union Fittings 3.0 S
80 dia.
165
124
226100
1400
1074
165
890
379 901
(25
0)
(47
0)
(80º
)
130
Stroke width
350
Stroke width
Air conditioner
11
0
14
80
to
15
80
Units:mm
KD7483AFWH
For Specific Applications Pipe typeKD74 series
KD7483AFWH Solids in fluid
Product size: 12 mm (Less than 1/3 of the minimum height of the inspection section)
KD7483AFWHAir conditioner is equipped as standard.
For Pumped Products
For Specific ApplicationsK
D74 series
KD
74-h seriesK
D74-f series
DualX
18
X-ray Inspection System
Anritsu believes customer safety is of utmost importance.
Anritsu safety mechanism
Safety management
Safety of inspected products
Emergency stop switchCuts power to x-ray and drive circuits,
stops the conveyor and x-ray radiation.
X-ray irradiation displayThe lamp is lit during x-ray
radiation.
Leakage prevention curtainPrevents x-ray leakage. For
unpackaged or bulk products,
the standard lead impregnated
curtains are replaced with SUS
plates and covers - preventing
direct food contact with the
curtains.
Hand insertion sensorInterrupting the sensor for a
certain period of time stops x-ray
radiation.
X-ray ON/OFF keyTurning the key to OFF stops x-ray
radiation completely.
X-ray shield cover open/close sensorOpening the cover stops x-ray radiation.
X-ray shield coverOpened/Closed using x-ray Irradiation
ON/OFF Key.
Opening the cover stops x-ray radiation
due to the x-ray Shield Cover Open/Close
Sensor.
X-ray Inspection System has been designed to fully satisfy the safe operation. However, to ensure even higher safety, use
the safety procedures outlined below.
1
3
Periodic measurement and recording of x-ray leakage data
Additional safety measures
Covers may need to be mounted on upstream and
downstream conveyors instead of the shield curtains,
depending on the shape, weight, and package of
products.
2
4
Management of operator working hours
No disassembly or modification
NEVER modify or disassemble the main unit, covers,
x-ray leakage prevention curtains, safety covers, safety
interlocks, etc., otherwise the x-ray leak-proof design
may no longer be functional.
WHO concluded in 1980 that the “irradiation of any food commodity up to an overall average dose of 10 kGy presents
no toxicological hazard and introduces no special nutritional or microbiological problems.”
The maximum dose of x-ray irradiation to the products to be inspected by our x-ray inspection systems is 0.002 Gy,
which is much lower than the value described above. Even if a product stops inside, the x-ray dose is always kept to
0.1 Gy or less.
Note: Follow the local laws and regulations regarding the installation and use of the x-ray inspection systems.
Safety in design
19
Note
X-ray Inspection System
KD74
KD74-h
KD74-f
DualX
For Specific Applications
October 2015
2015-10 (ddc) Printed in JapanCAT. NO. K3176-C-1
2014
