X-431 PADII Quick Start Guide (EN) LAUNCH - … PADII Quick Start Guide (EN) LAUNCH ... Pictures...
Transcript of X-431 PADII Quick Start Guide (EN) LAUNCH - … PADII Quick Start Guide (EN) LAUNCH ... Pictures...
Quick Start Guide (EN)X-431 PADII LAUNCH
Front & Side View
X-431 PADII Professional Tablet
Rear View
Accessory Checklist
*Note1: USB Port is reserved for add-on modules, and other USB devices use only. Micro USB Port is reserved for Micro USB cable only.
*Note2: X-431 PADII tablet is charging. Once charging is finished, it willturn green.
It illuminates red while
X-431 PADII Unit Docking Station Diagnostic Connector
OBDI Converter Password Envelope Non-16pin Connector
HDMI Cable Battery Clamps Cable OBDII Extension Cable
Power Adaptor Cigarette Lighter USB Cable
(A tablet for showing test results.)
(To supply power to the tablet.)
(To connect to anexternal projector or monitor with HDMI
interface.)
(A converting cable for connecting
non-16pin connector.)
(A piece of paper bearing Product S/N and Register
Password, which is required for your
registration.)
(To supply power to the non-16pin connector via
vehicle’s cigarette lighter socket.)
(To connect the diagnostic connector
and the display tablet.)
(To connect the diagnostic connector
for extension purpose.)
(To provide power to the non-16pin connector through connection to the vehicle’s battery.)
(See Section “Docking Station” on Page 2.)
(A device for accessing vehicle data.)
(Optional)
(For detailed non-16pin
connectors, please check
the package)
Pictures illustrated here are for reference purpose only and this Quick Start Guide is subject to change without notice.
Handgrip
Camera Flash
Rear Camera
Audio Speakers
Micro SD Card Slot
Mini HDMI Port
Volume Buttons
Reset Button
golo Button
(For Messaging application)
quick access to Instant
DC Input Port
1USB Port
Power Button
1Micro USB Port
Front Camera Charging Indicator2
Microphone
IPS Touch Screen
Charging Slot
Headphone Jack
Quick Start Guide (EN)X-431 PADII LAUNCH
Pictures illustrated here are for reference purpose only and this Quick Start Guide is subject to change without notice.
Diagnostic Connector
1. Locate vehicle’s DLC socket: It provides standard 16 pins and is generally located on driver’s side, about 12 inch away
from the center of dashboard. See Figure DLC Location. If DLC is not equipped under dashboard, a label indicating
its position will be given. In case no DLC is found, please refer to Automobile Repair Manual;
2. Plug the connector into the vehicle's DLC(It is suggested to use the OBD II extension cable to connect the DLC and the
connector). For vehicles with non-16PIN DLC, please choose the desired connector. Normally the power indicator of
diagnostic connector will light up.
Note: Remember to remove thediagnostic connector from the DLCif it keeps unattended.
NEAR CENTEROF DASH DLC Location
1. Charge X-431 PADII Tablet
Except that power adaptor supplies power to X-431 PADII, PADII can also obtain power from the Lithium polymer battery. Choose any of the followings to charge X-431 PADII tablet:
1. Use the included 5V power adaptor: Connect one end of the power adaptor to DC IN port of X-431 PADII, then connect the other end to the AC outlet. We assume no responsibility for damage or loss resulting from using other similar adaptors other than the specified one.
2. Use the docking station: Follow the steps described as below to charge your X-431 PADII tablet:
X-431
Docking
Statio
n
Install diagnostic connector
Note: If X-431 PADII tablet keeps idle or unattended for a long period, please lock the screen or turn it off to save power.
OBD II 16 PIN connector
Communication indicator
Power indicator
Micro USB port
Fig. a Fig. b
Locate the charging slot on the bottom of X-431 PADII tablet and the docking station. See Fig. a & Fig. b.
1
*Note3: It is designed to charge the display tablet. For details on how to charge, please refer to Section “Charge X-431 PADII Tablet” on the right.
*Note5: the socket for demo experience when the station is connected to the AC outlet.
Plug the diagnostic connector into
Power Interface
3Charging Slot
OBD 16 Socket without 4power output
OBD 16 Socket with 5power output
(Provides power to the docking station)*Note4: These 2 sockets are used to
store the additional DBScar/EasyDiag/golo diagnostic connector (separatelypurchased).
Fig. c
2
Align the charging slots, and then dock the tablet into the station to ensure that it firmly sits on the docking station. Refer to Fig. c. Insert one end of power cord of the docking station into the power jack, then plug the other end into the AC outlet.
2. Connections
Non-OBD II Vehicle Connection
OBD II Vehicle Connection
3. Power on, Wi-Fi connection, Register and Download software
1. Power on
Press the [POWER] button, the system starts initializing and then enters the desktop.
2. Wi-Fi connection
Tap [Settings] on the desktop and then [Wi-Fi] to configure Wi-Fi setting. Refer to Figure A.
Select the desired Wi-Fi connection from the list. (Password may be required for secured networks). When “Connected” appears, tap to return to the desktop.
(To be continued...)
3. Register (1. Tap “Login” --> 2. Register an Account --> 3. Activate Connector --> 4. Finish Register)1. Launch the application on the desktop to enter. Tap on “LOGIN” on the right upper corner
of the screen. 2. Tap on “New Register” in Figure B, input the information (items with * must be filled) and then tap on
“Register”. Refer to Figure C.3. Input the Product S/N and Activation Code (can be obtained from the password envelope, see Figure
F), and then tap on “Activate”. Refer to Figure D. 4. Tap on “Go To Update Center” to enter diagnostic software download screen. Refer to Figure E.
X-431 PADII
A Via Cigarette Lighter
A Directly plug the diagnostic connector into vehicle’s
DLC
B Via Battery Clamps Cable
B Using OBD II extension cable
To Vehicle’s DLC
OBD II ExtensionCable
To diagnostic connector
X-431 PADII LAUNCHQuick Start Guide (EN)
Login InterfaceB
Create an AccountC
A
Activation Code
Password Envelope
For more detailed operations, please refer to User’s Manual of X-431 PADII.
X-431 PADII LAUNCH
3. Power on, Wi-Fi connection, Register and Download software (Cont.)
4. Download & Update Software
Tap to start downloading.
Note: By default, all vehicle software are selected. To deselect certain software, just uncheck the box next to the software version.
Once downloading finished, the software packages will be installed automatically.
4. How to Diagnose
Follow the flowchart illustrated as below to diagnose a vehicle.
Tap “Diagnostic”
Select vehicle
Select test systemSelect test function
Select diagnostic software version
Tap “LOGIN” to register1
Activate connector?No
Tap “Update” to update software2
Yes
…… (Refer to Section 3)
Register & Activate OK
Notes:
* 1. To start diagnosing a vehicle, you have to register the diagnostic connector. For details, please refer to Section 3 “Power on, Wi-Fi connection, Register and Download Software” in this Quick Start Guide.
* 2. To perform update, tap and select “Update” from the pull-down list.
3. Register (Cont.)
Diagnosing Flowchart
Quick Start Guide (EN)
Activate ConnectorD
Finish Register
Where is my activation code?
G
Tap here to enterupdate center
E
F