Roadrunner Familiarization

Wylie, TX

Model number (3629/3630)

Rosenbauer

Safety Information

Please read all safety information!!

Safety Introduction

Familiarize yourself with all manuals supplied.

Read and follow all safety precautions

DO NOT MODIFY any equipment without authorization from the factory

Keep ignition sources away from flammable objects

Practice good housekeeping.

Safety Harnesses

For the safety of everyone on

your crew. A safety harness

MUST BE WORN at ALL

TIMES by any individual on

the aerial!

Positioning the Truck for Operation1. Determine if the aerial will be used as a water tower or for rescue.

2. Make sure to note ALL overhead obstructions.

3. Scan scene to position the truck for best attack.

NOTE: For the best positioning, a corner of a building is highly suggested. This gives the

operator access to two sides of the structure as well as the roof.

REMINDER: The operator should always observe the placement of the fire fighting vehicle to be

sure that there is enough space for the stabilizers to be set and the aerial to be operated without any

obstructions.

Obstructions to be most aware of include, but are not limited to: adjacent buildings, curbs, drop-

offs at road edges, man holes, vehicles, trees, over head electrical wires, ditches and culverts.

When setting up the stabilizers the ground must be firm. It is highly recommended that the

operator uses the outrigger pads provided. Setting up over manholes, underground parking

facilities or storm drains could cause serious damage to the operator and/or serious damage to the

truck. The area must be able to support 75 PSI

Setting Front of Truck to UPHILL Grades

With maximum grades the truck should be positioned with the

cab facing uphill. Aerial should be operated over the rear.

Advantages:1. Can reduce the truck’s grade by extending the rear outrigger

stabilizer jacks.

2. When truck is set up the front tires will be in contact with the

ground.

3. With the outriggers set operator has more ballast for the

operation of the aerial.

Setting Front of Truck to UPHILL Grades

Disadvantages:

1. Since only the front tires are on the ground there is less resistance

to prevent truck movement.

2. The rear compartment and aerial access step are more difficult to

access.

Setting Front of Truck to DOWNHILL

Grades

Advantages:

1. Rear compartments are closer to the ground for easier access.

2. Better resistance to keep the truck from sliding by having more

tires in contact with the ground.

Disadvantages:1. Can not reduce the trucks grade by extending the front outrigger stabilizer

jacks. FRONT TIRES MUST STAY ON THE GROUND WHEN

OPERATING OVER THE FRONT OF THE TRUCK.

2. It is possible that the truck will teeter if the aerial is operated over the front

stabilizers with the front tires off the ground.

3. Their will be less ballast for aerial operations with the rear tires on the ground.

Setting Front of Truck to DOWNHILL

Grades

Safety Around the Vehicle

EXHAUST FUMES

• Be conscious of exhaust fumes when working around the vehicle.

• Ensure that there is adequate ventilation.

• DO NOT alter emission controls.

COOLING SYSTEM

• Ensure there is adequate clearance between fan and shroud.

• DO NOT alter fan ratio, spacers or position.

• Observe fan clutch operation to ensure fan is disengaging when cooling is not

necessary.

AIR INTAKE SYSTEM

• DO NOT alter any intake piping or filter locations.

Safety Around the VehicleUNDERCARRIAGE

• Notify others when working underneath the vehicle.

• Keep away from moving parts.

• Avoid hot areas such as engine, transmission, exhaust and pumps.

• Avoid ports that may eject steam or other hot fluids.

COVERS AND DOORS

• DO NOT sit, stand, climb or hang on open doors.

• Some doors are spring loaded. Use caution when opening doors.

• Use care not to get fingers and hands caught in pinch points such as hinges.

• Do not drive with doors partially closed.

TIRES AND WHEELS

• DO NOT operate vehicle with damaged or improperly inflated tires.

PRECAUTIONS FOR

DRIVING SAFETY AND

AERIAL OPERATION

Vehicle Safety

ENTERING, EXITING AND CLIMBING

• Keep steps, handles, rails, walking surfaces and shoes free from grease.

• Use extreme caution during inclement weather or when surfaces are wet.

• DO NOT use pump fixtures or lights as stepping surfaces.

• Make deliberate movements when entering, exiting or climbing on the

vehicle. DO NOT rush.

• DO NOT climb in areas without slip resistant surfaces and hand holds.

• Use a three point stance in which three extremities are in contact with the

vehicle, when entering, exiting or climbing on the vehicle.

Vehicle Operational Safety

VEHICLE BACKING• Use a spotter when backing vehicle.

• Establish hand or verbal communication prior to backing.

• During periods of low light use spotter with wands and reflective vests.

VEHICLE CONTROL• Ensure proper tire inflation before operating vehicle.

• A neutral safety switch prevents vehicle from being started in gear.

• Allow starter to cool for one minute if vehicle doesn’t start within 15seconds.

• Familiarize yourself with gauges, switches and on-board accessories priorto operating vehicle.

WATCH YOUR TURNING!Increased overhangs, particularly at the rear, must be kept in mind.

NOTE: In narrow crossings the driver must confirm that there is enough space for turning.

KNOW YOUR TRAVEL HEIGHT!

KNOW YOUR TOTAL WEIGHT!NOTE: The driver must confirm the vehicle can freely pass limited weight areas.

WATCH YOUR ANGLE OF DEPARTURE!Ground clearance and the angels to front and rear structures

Our ground clearance is 8°

REMEMBER HIGH CENTER OF GRAVITY!

HEIGHT OF THE CENTER

OF GRAVITY.

NOTE: Speeding with the

vehicle when turning a corner

is DANGEROUS!

REMEMBER 60% OF YOUR

WEIGHT IS ABOVE YOU

Your truck!

Rosenbauer 68’ Roadrunner

Rosenbauer Commander chassis

Cummins ISL 450hp Engine

Waterous S100 1750gpm pump

500 gallon water tank

8kw Onan Hyd

Cab Tilt Procedures

• Before tilting cab check the

following:

• Front bumper storage lid is

closed.

• No equipment on front

bumper.

• Inside cab -all loose

equipment removed such as

air packs, books, portable

radios, helmets, etc.

You MUST set the jacks and raise the

aerial BEFORE tilting the cab!

• Raise the Aerial to 20 degrees

• Shut the engine down

• Leave battery switch on

• Go to right side pump panel

compartment

• Operate switch to raise cab

Check Safety Bar

Lowering Cab

• Check to see if area is clear to lower

cab!

• Raise cab fully

• Pull cable until cab safety lock is

away from the cab cylinder and hold

• Hold switch down

• Cab will automatically lock down

Pump & Plumbing Info

Waterous S100 1750 GPM pump

Stainless Steel plumbing

Discharges

Crosslays

2-1/2” Discharges

LDH Discharges

Anti-Electrocution Platform

The pump control panel operator

should stand on anti-electrocution

platform when the aerial is being

operated.

Standing on the anti-electrocution

platform will raise the pump

operator off the ground and keep the

operator from being a pathway to

ground for electrical current if the

aerial contacts and energized line.

In-Control Governor

Master Pressure and Engine

Displays

STANDARD FEATURES

•Power Up in Pressure Mode

•Automatic Regulation of Pump Discharge Pressure

•Manual Control of Pressure or Engine RPM Settings

•Field Programmable Presets

•Diagnostic Capabilities

•No Pressure or RPM Variation When Changing Modes

•Limits Increase of Pressure When in RPM Mode

•Recognition of No Water Condition With Automatic Response

•Interlock Signal Recognition and OK To Pump LED

•Return to Engine Idle With the Push of a Button

•Off-The-Shelf Programmable for Engine Type

Pump Engagement

Neutral

Switch from Road to Pump

Shift to 4th gear

Pump Priming System

Waterous oil – less primer

33

Drains

Generator Electrical Panel

Generator has a monitoring system that lets you see amps, line voltage, and frequencies.

Breaker panel box is equipped with GFI breakers.

Cummins DPF

Aerial Technical

Information

Aerial VocabularyAerial Types:

Mid-Mounted Aerial Ladder

Rear-Mounted Aerial Ladder

Mid-Mounted Aerial Platform

Rear-Mounted Aerial Platform

Aerial VocabularyBase-Section – the lowest most section on an aerial

Mid-Section – is any of the sections used between the base section and the fly section

Fly-Section – the top most section on an aerial

Short-Jack Operation – allowing aerial to operate in predefined zones with outriggers/stabilizers not fully extend

Torque Box (tube) – part of an aerial attached below the turntable to transfer torsion loads to the chassis

and outriggers.

Turntable – part of the aerial device attached to the base ladder section designed to articulate the

position for rescue or firefighting

E-Tracking - a flexible track utilized to protect electrical, communication and control wires in aerial

extension/retraction

Soft-Touch Control - electric control of aerial functions through the use of a remote manual control

programmed to slowly start and stop aerial functions

Auto-Bedding Control – automatic aerial bedding when aerial is in predefined zone

Dead Load – weight of aerial and attached mechanism and equipment

Live Load (Tip Load) – weight and forces exerted on the aerial by payload, and water stream reactions.

Outrigger/stabilizer – a hydraulic lifting mechanism designed to prevent aerial overturn and transfer

loads to the ground

Aerial Vocabulary

Rated Capacity – total weight of payload at the outermost ladder rung or platform according to ladder load chart

Cab-Body Collision Protection – program preventing aerial device from collision with chassis and equipment mounted on the body

Pinable Waterway – manual device designed to place the waterway at the tip or next lower section

Modified Warren Bridge – design of aerial structure to transfer loads up and down the aerial device.

Bolt-On Egress – outermost extension device designed for personnel to climb on/off the end of the aerial

Yield Strength – point at which the material exhibits a permanent deformation or set

Water Load – stress produced by water weight and nozzle reaction overhead to the side and below stream applications

Hot Dipped Galvanized – a process for treating steel ladder and stabilizers to prevent corrosion and oxidation on the inside and outside of all the ladder parts

Aerial Vocabulary

Dead load Stress – stress produced by the aerial structure weight and any permanently mounted or

manufactured equipment

Rated Capacity Stress – stress produced by the aerial rated capacity applied to the tip of the fly section

Water Reaction Stress - weight of the water and nozzle reaction force

Material Yield Stress – the stress at which a material exhibits a distortion or permanent set

Load Limit Indicators (Load Charts) - a load indicator or instruction plate, visible at the operators

position, showing the recommended safe load at any condition of the aerial’s elevation and extension

Aerial Vocabulary

68’ 3-Section Elevated Water Tower

• 2 Outriggers A-Frame 11’ 9” spread

• Tip load wet of 500 lbs.. Dry 1000 lbs.

• Water flowing at 1250 GPM 45° to the side

• Horizontal reach at 0° is 59’

• Elevation of -10° to 75° vertical height

• Axel ratings 22,800 front & 31,500 single rear

• Wheel base 222”

• Standard Height – 12’ 5”

• Standard Length – 36’ 10”

Load Chart

Setting Up the Cab for Aerial

Operations1. Shift transmission (1) from drive into neutral.

2. Apply the parking brake (2).

3. Switch on the aerial master (3). When the aerial master is

switched on there is electrical power to the aerial system. At

this time flashing lights on the outriggers will begin to

operate.

4. Switch on the Power Take-Off (PTO).

Note: It is important to note that step # 4 cannot be performed

before step # 3 has been completed and step # 2 cannot be

completed until step # 1 has been completed. Some trucks

will have the aerial master and PTO switch combined .

The transmission must be in neutral (4) or 4th gear for the

water pump to be engaged. The parking brake must be set

before the ladder power will operate. If the water pump is

engaged, the high idle of the aerial will be disengaged.

12

4

3

Outrigger Operation Set Up

• Once the ladder power is activated,

the flashing light (1) on the inside

of the outrigger jack tubes will

begin to flash and the outrigger

jack scene lights (2) will come on.

• Outriggers are ready to operate. 1

1

2

Outrigger Operation Set UpWith tire chocks set the operator will proceed to the outrigger station.

1. Move Aerial/Stabilizer On/Off/On Switch to the Stablizer ON position

This will cause the high idle to engage and the warning alarm will begin. The alarm alerts all other personnel the outriggers are being positioned. If the water pump is engaged the high idle of the aerial will be disengaged.

2. Use Controllers to set the outriggers.

The outrigger controls are located to the back, outside of the truck to provide the operator a good clear vision to set up the outriggers.

The controllers are designed to move in the same direction as the corresponding outrigger. (Example: To extend the right outrigger you would push the controller to the right to extend and to the left to retract.)

3. Position outrigger pads under jack locations

Outrigger Operation Set Up

4. Lower outrigger jacks

Take the bubble out of the truck tire or

level truck as much as possible.

As the truck is leveled or the bubble is

taken out, each Jack Indicator Light will

respond according to how the outrigger is

set.

Outrigger Operation Set Up

5. When outriggers are set move the

Aerial/Stabilizer On/Off/On Switch

to the OFF position or Aerial On

position.

6. Outrigger operation set up is

completed.

Outrigger Operation Set Up

Control Panel1. Aerial/Stabilizer On/Off/On Switch

2. High Idle Switch

3. Tracking Lights Switch

4. Tip Lights Switch

5. Emergency Backup Pump Switch

6. Radio Remote Switch

7. Change Hydraulic Filter when Light is on Light

8. Rungs Aligned Light

9. Ladder Aligned with Bed Light

10. Flow Minder

11. Flow Minder Totalizer

12. Hour Meter

13. System Pressure Gauge

14. Boom Controls

15. Monitor Controls

1

2

5

8

34

6 7

9

15

1012

11

1314

1. Aerial/Stabilizer Switch

To run the aerial this switch needs to

be placed up in the on position. To

run the stabilizers this switch needs

to be placed in the down position.

Control Panel

1

2. High Idle Switch

This switch will activate the high idle and raise

the RPM’s. Push up on the switch to activate.

The switch must be activated in order to operate

the outriggers or the boom. The high idle will not

work if the water pump is engaged.

Control Panel

2

3. Tracking Lights Switch

To activate the tracking lights (lights located on

the base section in front of the elevation

cylinders) this switch will need to be placed in

the on position. This switch will activate all

AC and DC tracking lights as well as the panel

light and optional rung lighting. Most AC and

DC lights provided also include a switch on the

lamp head itself. If personnel switched the

switch on the lamp head to the off position the

operator will not be able to override it from the

control panel. The switch will need to be

reengaged from the lamp head.

Control Panel

3

Control Panel

4

4. Tip Lights Switch

To activate the tip lights (lights located on the

fly section) this switch will need to be placed in

the on position. This switch will activate all

AC and DC lights at the tip. Most AC and DC

lights provided also include a switch on the

lamp head itself. If personnel switched the

switch on the lamp head to the off position the

operator will not be able to override it from the

control panel. The switch will need to be

reengaged from the lamp head.

5. Emergency Back-Up Pump On/Off

Switch

The sole purpose of the Emergency Back-Up

Pump is to stow the aerial in case of hydraulic

failure.

To Use Emergency Back-Up Pump

1. Select the operation required (outrigger or

aerial) and move switch to the on position.

2. Engage the outrigger or aerial control handle.

3. Activate momentarily the Emergency 12V

Back-Up Pump

4. To ensure that the Emergency Back-Up

Pump doesn’t over heat, it can only operate 5

minutes out of 60.

Control Panel

5

6. Wireless Radio Remote Switch

In order to operate the boom from the

wireless radio remote, place this switch to

the on position. The operator at the

turntable control stand can override the

wireless radio remote at anytime by placing

the radio remote switch to the off position.

Control Panel

6

7. Change Hydraulic Filter Light

When this light is illuminated the high

pressure and return hydraulic filters are

dirty and need to be changed, both filters

are connected to the same light.

Control Panel

7

8. Rungs Aligned Light

The ring alignment light will illuminate

when the rungs are aligned. While

extending or retracting the aerial this light

will flash on and off in accordance with the

rungs being aligned. It is recommended

that the rungs be aligned when personnel

are climbing the aerial for personal safety.

Control Panel

8

9. Boom Aligned with Bed Light

The boom aligned with bed light will be

illuminated when the boom is aligned with

the bed and ready to be stowed.

Control Panel

9

10. Flowmeter

The flowmeter will give a continuous

reading of the water flowing from the

monitor. Depending on options this could

be a combination pressure and flow gauge

and will vary by manufacturer.

11. Flowmeter Totalizer

The totalizer button only comes with certain

flow gauges. Press the button to get the

total amount of water flown.

Control Panel

1011

12. Hour meter

The hour meter keeps record of the hours

the aerial has operated (only while the aerial

is moving).

Control Panel

12

13. System Pressure Gauge

This gauge show the current hydraulic

system pressure while the aerial is

operating.

Control Panel

13

14. Boom Controls

The three controllers will operate the aerial

functions (extend/retract, left/right &

raise/lower). In order to activate the

controller pull up on the locking mechanism

on the bottom side of the controller. Push

or pull the appropriate controller to move

the aerial. See aerial operations.

Control Panel

14

15. Monitor Controls

Three monitor toggle switches or the

manufactured monitor controls will control

the monitor (stream/shape, right/left,

raise/lower). Push up on the individual

switches to activate the stream, right and

lower functions of the monitor. Push down

on the individual switches to activate the

shape, left and lower functions of the

monitor. To turn off the switches the

operator will need to release the switch to

the neutral position.

Control Panel

15

Wireless Radio Controls

1. Aerial Extend/Retract

2. Aerial Clockwise/Counter Clockwise

3. Aerial Lower/Raise

4. On/Off

5. Enable/Frequency

6. 100% / 50%

7. Auto Bedding Switch

8. Feedback Screen

9. Left Monitor/Right Monitor (Option)

10. Monitor Clockwise/Counter Clockwise

11. Monitor Raise/Lower

Wireless Radio Remote

In order the use the wireless radio remote the radio remote switch needs to be turned to the on position on the turntable control console.

1. Turn the on/off switch to the on position

2. Push the enable switch and operate one of the aerial functions within two seconds. If the aerial functions have ceased for more than 5 seconds the enable switch must be pushed again to start aerial operations.

• NOTE: If no aerial or monitor operation occurs, release the enable switch and move it to the frequency side to find a new frequency and then back to enable to operate aerial or monitor function.

Wireless Radio Remote

3. If you want to run the aerial at 100% speed turn the 100%/50% switch to 100%. If you want to run it at approximately half speed switch it to 50%.

4. Use the aerial extend/retract, clockwise/counterclockwise and lower/raise joysticks to operate the aerial to the desired location.

For monitor controls the radio transmitter must be turned on and the monitor switched will be activated. The monitor controls run the monitor stream/shape, clockwise/counterclockwise and raise/lower momentary switches.

The feedback screen will give the operator continuous readings of aerial position including extension, rotation, elevation, aerial load, outrigger deployment and breathing air levels.

Wireless Radio Remote

Aerial Intercom

Push the talk switch to communicate to

the other intercom. The volume knob

adjust the sound.

Aerial Intercom

Warning Labels

The warning labels are located in the lid and

will warn the operator of potential life

threatening situations that could occur when

operating the aerial.

Aerial Warnings

• 3 ways to use your aerial to flow water

– From main pump through Aerial Devise

– From external source to Aerial Devise

– From main pump and use waterway inlet as a large

diameter discharge.

Water Flow

• To discharge water from the main fire pump through the aerial devise:

– Open the Aerial Discharge valve at the pump panel

– Open the Aerial butterfly valve at the turn table.

Water Flow From Pump

• To discharge water from relay operations through the aerial devise:

– Close the Aerial Discharge valve at the pump panel

– Open the Aerial butterfly valve at the turn table.

– Connect incoming water source to Waterway Inlet at rear.

Water Flow From Relay

• To discharge water from rear aerial waterway / discharge connection:

– Open the Aerial Discharge valve at the pump panel

– Close the Aerial butterfly valve at the turn table.

– Connect discharge hose to Waterway / Inlet at rear.

Water Flow From LDH

Practical operations of aerial to include:

1. Positioning of the truck

2. Outrigger operation, placement and setup

3. Operation of the aerial from the turn table

4. Operation of the aerial from the remote control

5. Moving water

Overview

QUESTIONS?