univox Loop Systems, since 1965.

www.univox.eu

www.univox.us www.edin.se

SLS - Loop systemsunivox Loop Systems, since 1965

www.univox.eu


Conventional loops:Overspill (energy/space wasted leakage)

Head tilt problem (directivity)

Acoustic and Inductive feedback/interference

Metallic influence/interference

Variable field - level / frequency drop in middle area

Needs experienced expertise for planning

www.univox.eu


Conventional Loops = overspill

www.univox.eu


SLS = no overspill

www.univox.eu


Conventional Loop - overspill

www.univox.eu


SLS – No overspill

www.univox.eu


Tilt angle – conventional loop

www.univox.eu


-3dB (@45°)-3dB (@45°)

Conventional loops - tilt angel

0dB=full level

Silence!

Vertical field

Silence!

www.univox.eu


-3dB (@45°)-3dB (@45°)

New Loops- both directions

0dB=full level

full levelfull level

Vertical AND Horizontal Field

www.univox.eu


SLS – No overspill

www.univox.eu


SLS-XF, second generation

• One unit, 2 matched stages and built-in SLS-filter

• Increased internal high frequency range 10-16 kHz

• Fully matched output stages and filter

• Super safe technology

• 12 Power transistor of each 25A current capability

• Increased output voltage: 30Volt – 50Volt

• Built-in auto-SCART-function

www.univox.eu


IEC 60118-4 standard

univox Loop Systems, since 1965

www.univox.eu


IEC 60118-4, Scope + Facts

Background noise less than -47dBA, -32dBA

Frequency range 100-5000HzField variation +-3dBLevel 0dB = 400mA/m (clarity and less

noise)

Specifies the Field strength

www.univox.eu


IEC 60118-4, CommentsLoop Amplifier can NOT be IEC

60118-4 approved IEC 60118-4 Specifies ONLY the Field Strength

Do NOT trust the stated coverage area for Loop Amplifier Trust the written certificate from the installer Compare the output current and/or power

consumption for Loop Amp

Measurement report - certificateLevel = 400mA/m for speech

(clarity, no noise)

www.univox.eu


High Noise, Low field strength

Field Strength -12dB (16-times less power below standard)

Noise -12dB (20 dB higher than the standard)

www.univox.eu


Field comply but NoisyField Strength

0dB=400mA/mNoise -12dB

www.univox.eu


Minimum IEC-standard!Field Strength

0dBNoise -32dB

www.univox.eu


Wireless system needed!

Do NOT trust stated coverage area!

Certify according to IEC

LEVEL = 400mA/m (0dB)Do NOT certify using a Hearing Aid.

www.univox.eu


Why a Loop System?

univox Loop Systems, since 1965

www.univox.eu


Why a Loop System?

DistortionEchoReverberationAbsorptionNoise> human speech noiseFrequency limitation

Sound in air has problems:

www.univox.eu


Hearing Aid, Mic-input

2 sec reverberation time, large building-church

Speaker 4mBabble noise (other speakers)Direct from a Hearing Aid (artificial

ear)

www.univox.eu


Wireless system needed!

Difficult to filter out reverberation

Impossible to filter out speech from speech

Solution: shorter microphone distance (wireless system)

www.univox.eu


IR – Radio - Loops

IR – infrared No overspillDifferent frequencies – partly

standardizedSensitive to direct sun light

Radio and Infra Red (IR) High current consumption compared to

HA (0.3-1.5mA) Not Compatibility with Hearing Aid (neck

loop) Separat unit outside HA No world-wide standard

(2.4GHz streamers, not standardized)

www.univox.eu


Loop System – fundamentals

Built-in reciever in HA

Zero Current consumption, T-coil

World Wide Standard

www.univox.eu


Loop Systems – users view

InvisibleEconomical = No extra costly unitNo additional knowledgeNo channel switching, level settingNo changing battery/charging hassleEconomical = No extra unit+Zero

CurrentLong life = system is not tampered

withIndividual fitted hearing aidCompatible everywhere-World Wide

www.univox.eu


Homogenous sound

www.univox.eu


Thank you for your attention!

[email protected]

univox Loop Systems, since 1965.

Documents

Transcript of univox Loop Systems, since 1965.