Www.technologyfuturae.com By ANJU K P Edited By Sarath S Nair M ODELING AND S PEED C ONTROL OF B...
-
Upload
kirsten-higgins -
Category
Documents
-
view
215 -
download
3
Transcript of Www.technologyfuturae.com By ANJU K P Edited By Sarath S Nair M ODELING AND S PEED C ONTROL OF B...
ww
w.te
chn
olo
gyfu
tura
e.co
m
By ANJU K P
Edited BySarath S Nair
www.technologyfuturae.com
MODELING AND SPEED CONTROL OF
BRUSHLESS DC MOTOR DRIVESBY LOAD TORQUE ESTIMATION
ww
w.te
chn
olo
gyfu
tura
e.co
m
OVERVIEW
Introduction BLDC Advantages, disadvantages and applications
of BLDC Modeling of BLDC and current control method Conclusions References
ww
w.te
chn
olo
gyfu
tura
e.co
mINTRODUCTION
DC motors have many attractive properties such as high efficiency and linear torque speed characteristics .
The control of dc motors is simple and their hardware is less.
The main drawback of dc motor is the need of periodic maintenance
Thus DC motors have been gradually replaced by the BLDC
ww
w.te
chn
olo
gyfu
tura
e.co
m
The PI controller is usually employed in a BLDC motor control, which is simple in realization. But it is difficult to obtain the sufficiently high-performance applications.
Used a feedforward compensation method through load torque estimation
The estimated load disturbance by the state observer is compensated as the equivalent current
The d-q transform of phase currents were possible by the Fourier series summation method
This current control method was used to get compensation current of BLDC motor.
ww
w.te
chn
olo
gyfu
tura
e.co
m
BLDC
Permanent magnet synchronous motor, having permanent magnets on the rotor and trapezoidal shape back EMF.
The BLDC motor employs a dc power supply switched to the stator phase windings of the motor by power devices, the switching sequence being determined from the rotor position.
BLDC is driven by a three-phase inverter with, six-step commutation
Commutation timing is determined by the rotor position, which can be detected by Hall sensors
ww
w.te
chn
olo
gyfu
tura
e.co
mADVANTAGES, DISADVANTAGES AND APPLICATIONS OF BLDC
ADVANTAGES More Efficient Less electrical energy is wasted Reduced Noise Longer Lifetime Reduced EM Interference. Torque, Voltage, And RPM Linearly Related DISADVANTAGES High cost More complex controller
ww
w.te
chn
olo
gyfu
tura
e.co
mAPPLICATIONS
They are having different power ratings from very small motors as used in hard disks to larger motors in electric vehicles
hard drives, CD/DVD players, and PC cooling fans use BLDC motors.
High power BLDC motors are found in electric vehicles and some industrial machinery.
A number of electric bicycles use BLDC motors
Certain HVAC systems, especially those featuring variable-speed and/or load modulation, use ECM motors .
ww
w.te
chn
olo
gyfu
tura
e.co
m
ww
w.te
chn
olo
gyfu
tura
e.co
m
MODELING OF THE BLDC MOTOR AND CURRENT CONTROL METHOD
ww
w.te
chn
olo
gyfu
tura
e.co
m
MODELING OF BLDC MOTOR
The BLDC motor is an AC synchronous motor The BLDC motor has three stator windings
and permanent magnets on the rotor. The modeling is based on the following
assumptions:(1) The motor is not saturated.(2) Stator resistances of all windings are equal
and self and mutual inductances are constant.
(3) Power semiconductor devices in the inverter are ideal.
(4) Iron Losses are negligible.
ww
w.te
chn
olo
gyfu
tura
e.co
m
BLOCK DIAGRAM OF BLDC MOTOR DRIVE
ww
w.te
chn
olo
gyfu
tura
e.co
m
Under the above assumptions, a BLDC motor can be represented as
where ia, ib , and ic are rectangular shaped phase currents and ea, eb and ec are trapezoidal shaped back-EMFs. The electromagnetic torque is expressed as
where, wm is mechanical speed
ww
w.te
chn
olo
gyfu
tura
e.co
m
CURRENT CONTROL METHOD
Input current reference value was calculated from the summation method of the Fourier series.
Phase current is rectangular shape and then, it's Fourier series is expressed as
Where a0=0 and an=0, because it is odd function
ww
w.te
chn
olo
gyfu
tura
e.co
m
using above eqn d-q transform of phase current can be done
the electromagnetic torque is rewritten as
α is proportional constant for feedforward compensation, λm is linkage flux of permanent magnet, andiq is q axis stator current
ww
w.te
chn
olo
gyfu
tura
e.co
m
The interaction of T, with the mechanical dynamics
where TL is the load torque, J is the inertia, w is the rotor speed, and B is the viscous damping.
ww
w.te
chn
olo
gyfu
tura
e.co
m
BLOCK DIAGRAM OF PROPOSED CONTROL ALGORITHM
BLDCM
ww
w.te
chn
olo
gyfu
tura
e.co
m
LOAD TORQUE OBSERVER The proposed speed control method requires information
of the load torque for feedforward compensation. A direct measurement of the load torque is difficult
because other high cost equipment is required. Therefore, we use state observer to estimate value. Input
value of the state observer is position information of rotor. The system equations of a motor can be described as
where y is the rotor position
ww
w.te
chn
olo
gyfu
tura
e.co
m The dynamic equation of the given system
can be expressed as
ww
w.te
chn
olo
gyfu
tura
e.co
m
A state observer for the load torque estimation can be represented as follows
ww
w.te
chn
olo
gyfu
tura
e.co
m
Estimated state vector can be represented as
is the proportional gain vector to be chosen so as to determine the error dynamics of the observer
ww
w.te
chn
olo
gyfu
tura
e.co
m
Estimated outputs of the observer are rotor position, speed,and load torque.
Estimated load torque is used for feedforward compensation
Reference current iq* is compensated as iq,com by estimated
motor speed quickly converges the reference shortly after startup and recovers very well from the load torque disturbance as well as parameters variation
ww
w.te
chn
olo
gyfu
tura
e.co
m
ww
w.te
chn
olo
gyfu
tura
e.co
m
ww
w.te
chn
olo
gyfu
tura
e.co
m
ww
w.te
chn
olo
gyfu
tura
e.co
m
CONCLUSIONS
Though BLDC is costly and its control circuit is complex, it replaces DC motors in many applications due to its wide advantages . The basics of BLDC was discussed.
The feedforward compensation control improves the overall speed control performance in low speed controller gain. This technique was also discussed.
It is regarded as the best control method to get fast and accurate speed response.
ww
w.te
chn
olo
gyfu
tura
e.co
m
REFERENCES
[1]Ki-Hong Park, Tae-Sung Kim, Sung-Chan Ahn, Dong-Seok Hyun,”Speed Control of High-PerformanceBrushless DC Motor Drives by Load Torque Estimation”.
[2]K. Ohishi, M. Nakao, K. Ohnishi and K. Miyachi,“Microprocessor-Controlled DC Motor for Load-Insensitive Position Servo System,” IEEE Trans. Ind. Electron., vol. 34, no. 1, pp. 44-49,1987.
[3]Jong Sun KO, Jung Hoon Lee, Se Kyo Chung, and Myung Joong Youn,“A Robust Digital Position Control of Brushless DC motor with Dead Beat Load Torque Observer,” IEEE Trans. Ind. Electron., vol. 40, no. 5,pp. 512-520, May 1993.
ww
w.te
chn
olo
gyfu
tura
e.co
m
[4]P.Pillay and R. Krishnan, “Application Characteristics of Permanent Magnet Synchronous and Brushless dc Motors for Servo Drives,” IEEE Trans. Ind. Appl., vol. 27, no.5, pp. 986-996 Sept./Oct. 1991.
[5]Guchuan Zhu, Dessaint, L.-A., Akhrif, O., and Kaddouri, A., “Speedtracking control of a permanent-magnet synchronous motor with state and load torque observer,” IEEE Trans, vol. 47, no. 2, pp. 346-355, Apr.2000.
[6]Stefán Baldursson,”BLDC Motor Modelling and Control – A Matlab®/Simulink®Implementation” Master Thesis work , Institutionen för Energi och Miljö International masters program in Electric Power Engineering , Chalmerstekniska HogskolaGöteborg, Sverige, 2005
Log On to www.technologyfuturae.com
Technology Futurae
Technical Presentations, Research Reviews, New designs & Developments
ww
w.te
chn
olo
gyfu
tura
e.co
m
THANK YOU…