Www.ihe.net PCD Infusion Pump WG Containment / Mode / Status Discussion (rev. 2) Updated: 2012.04.23...
-
Upload
mason-cochran -
Category
Documents
-
view
219 -
download
4
Transcript of Www.ihe.net PCD Infusion Pump WG Containment / Mode / Status Discussion (rev. 2) Updated: 2012.04.23...
www.ihe.netwww.ihe.net
PCD Infusion Pump WGContainment / Mode / Status
Discussion (rev. 2)
Updated: 2012.04.23 Monday
www.ihe.net2
DS-IP-xyz Containment/Mode/StatusDiscussion Scope:
Review proposed containment models for : DS – Infusion Pump – LVP DS – Infusion Pump – Syringe DS – Infusion Pump – PCA
Define role and values for pump Mode parameter Define purpose and values for pump Status parameter
www.ihe.net3
DS-IP-LVP Containment Model
VMDs are paired with technology-specific delivery channels
Source Channels package semantics that define / drive the behavior of a Delivery Channel
Multiple source channels can be “active” at any point in time.
www.ihe.net4
DS-IP-Syringe Containment Model
Syringe-specific parameters are contained in the Syringe Delivery Channel
Source Channels are the same as those available for LVP Delivery Channels
www.ihe.net5
DS-IP-LVP-PCA Model
PCA specific parameters are packaged in a PCA Source Channel
PCA Source Channel can be combined with other Source Channels as needed
PCA Source Channel can be combined with any Delivery Channel (LVP or Syringe)
PCA Source Channels may operate exclusively, sequentially or concurrently with one or more other Source Channels.
www.ihe.net6
DS-IP-Syringe-PCA Containment Model
Only difference is the choice of the Syringe Delivery Channel “mechanism”
www.ihe.net7
Pump Mode & Status ParametersDiscussion Points:
Operational Mode & Status contained in delivery channels Mode reflects …
what source channels are actively determining the operation of their associated delivery channel
What the user would “see” as the configured “mode” All source channels OR only currently active source channels?
Status reflects … primarily what is observed in the distal line … ?
ISSUE #1: What do we want these values to be for DS-IP-xyz? Including active / concurrent source channel indication
ISSUE #2: Harmonization with the 11073-10101:2004 Definitions
www.ihe.net8
X73 Pump “Mode” ParameterMDC_PUMP_MODE
(from 11073-10101:2004, A.7.7.12)
hRTM Group: “Operational Mode”: pump-mode-nominal pump-mode-drug-dosing pump-mode-ramp-taper pump-mode-multi-step pump-mode-multi-dosing pump-mode-bolus pump-mode-loading-dose pump-mode-multi-channel pump-mode-pca pump-mode-continuous pump-mode-pca-and-continuous pump-mode-piggyback pump-mode-concurrent
www.ihe.net9
X73 Pump “Status” Parameter
(from 11073-10101:2004, A.7.7.18)
MDC_PUMP_STAT
hRTM Group: “Operational Mode”: pump-status-ready pump-status-infusing pump-status-paused pump-status-kvo pump-status-delayed pump-status-standby pump-status-vtbi-complete pump-status-off pump-status-priming
www.ihe.net10
Proposed Resolution Define two Operational Mode parameters + 1 status parameter MDC_PUMP_MODE_SETTING (proposed)
Indicates the configured infusion “protocol” Enumerations include: pump-mode-continuous / -piggyback / -
pca / … Multiple mode “bits” can be set
MDC_PUMP_MODE_CURRENT (proposed) Indicates the actual operational – including simultaneous –
operational modes Enumerations - same as MDC_PUMP_MODE_SETTING
MDC_PUMP_STAT (… can we make this _STATUS?) Indicates what the pumping mechanism is doing Does NOT include alarm status indication (separate parameter) Enumerations include: pump-status-ready / -infusing / -paused /
-delayed / -standby / -off / …
www.ihe.netwww.ihe.net
PCD Rules!