HANSIN ELECTRONICS TRADING

LAGUNASTAR INDUSTRIES COMPANYShop = 3rd Flr Unit C22 Banawe De Sta Rosa Phase 2 Balibago, Santa Rosa City, Laguna

Mob/Tel : 0933-5996622, 0932-8688548 , ( 049) 5020789

lagunastar1@gmail.com , lagunastar2@gmail.com

www.hanstartools.com , http://soldering102.blogspot.com

LOW COST, WILL GET THE JOB DONE VAT Reg. TIN 007-434-260-000

TECHNICAL DATA SHEETWrist Strap System Tester 1. EXACT-171 Wrist Strap TesterAnti-static wrist strap tester model EXACT-171 provides simple and reliable tests.

The operator wears the wrist strap band on their wrist as normal.

Insert the banana plug into the jack located on the front of the wrist strap tester.

Then push the metal push button on the wrist strap tester.

The tester measures the resistance of the ground path from the skin of the operator through the ground cord of the wrist strap.

A properly operating wrist strap will give an "OK" LED indication on the wrist strap tester. If either RED "FAIL LOW" or

YELLOW "FAIL HIGH" LED's light, and the audible indicator sounds, then the wrist strap should be discarded and replaced with a new one.

small size, cordless, portable operation , performs test of anti-static wrist straps

Visual and audible fail indication , simple push button test

Uses 9V Battery, with low battery indicator (low indicator set at 6.5V)SpecificationsLED Display Resistance Value (5%) Indicator Status

OK (Green)800K to ~ 10MON

HI (Yellow)10M and aboveYES

LO (Red)800K and belowYES

Test parameters are factory set to pass 800K to 10M, but can be calibrated to match your own specifications via 3 internal potentiometers.

operating temperature 50F to 104F (10C to 40C)

storage temperature 5F to 140F (-15C to 60C)

relative humidity: 0% to 90%

accuracy: 5%

net weight: 5.2oz (145g)

dimensions: 2.8in W x 3.54in L x 1.1in T (7.1cm x 9.0cm x 2.8cm)

2. EXALT-498 Wrist Strap Tester-Used to check wrist straps and ground cords, as well as the contact resistance between wrist strap and skin. - To operate, simply connect the tester to the ground cord of the wrist strap assembly, and press the finger pad. - If the wrist strap and ground cord are working properly (resistance between 500K and 10M), the green "GOOD" lamp will light up and an audible signal will be heard. A lit red "HIGH" lamp, with no audible signal heard, indicates loose contact between wrist band and skin (resistance greater than 10M). A lit red "LOW" lamp, with no audible signal heard, indicates a faulty ground cord resistor (resistance less than 500K). - It comes with 8-ft. grounding wire and 9V battery.

Can be used anywhere for quick and easy checking variety of grounding systems.

Ensures employee safety.

Eliminates product defects caused by static electricity.

9V Battery operated (included) Size:110x72x40mm , Weight:200g

LED IndicationCalibration ResistanceBuzzer

LOW (Red)R < 800K ohmOFF

GOOD (Green)800K ohm - 9M ohmON

HIGH (Red)R > 9M ohmOFF

Note: The tolerance in resistance is set to 0 +10% for the

Lower Limit of 800 KiloOhm and -10% to 0 for the upper limit of 9 MegaOhm

======================================================================================== 3. HANSIN 498 Wrist Strap Tester

- Same Specs & Operation as Exalt & Hakko 498, but it is the Economy Version. -Fit for Non- heavy users or small repair centers onlyLAGUNASTAR INDUSTRIES COMPANY

http://soldering102.blogspot.comlagunastar1@gmail.com lagunastar2@gmail.comMob/Tel. 0933-5996622 049-5308463