Workshop practice ii lecture notes
-
Upload
jean-de-dieu-iyakaremye -
Category
Engineering
-
view
979 -
download
7
Transcript of Workshop practice ii lecture notes
![Page 1: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/1.jpg)
WORKSHOP PRACTICE IILECTURE NOTES
BYJean de Dieu IYAKAREMYE (Msc)
Email: [email protected] of Rwanda
![Page 2: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/2.jpg)
AGM 204 WORKSHOP PRACTICE AND APPLICATIONS
• Component Name: Workshop Practice II Part 1: Drilling operationPart 2: Welding ProcessesPart 3: Lathe machine
![Page 3: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/3.jpg)
Workshop Practice II
Part I. Drilling operation
![Page 4: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/4.jpg)
1. Introduction
• Drilling is a process of producing round holes in a solid material or enlarging existing holes with the use of multi-tooth cutting tools called drills or drill bits.
• The hole is produced by axially feeding the rotating drill into the workpiece which is held on the table of the drilling machine.
• The most common widely employed drilling tool is the twist drill.
![Page 5: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/5.jpg)
2. Types of holes
• Drilled holes can be either through holes or blind holes (see Figure 1 on the next slide).
• A through holes is made when a drill exits the opposite side of the work; in blind hole the drill does not exit on the other side of the workpiece.
![Page 6: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/6.jpg)
• Two types of holes: (a) through hole and (b) blind hole
![Page 7: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/7.jpg)
3. Drilling machines - Drill press
![Page 8: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/8.jpg)
3.1. Types of Drilling Machines
• The sensitive or bench drill is used for light drilling on small parts.
• The upright drill press is used for heavy duty drilling and finally the radial drill press is used for drilling large, heavy work piece that are difficult to move.
![Page 9: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/9.jpg)
• Sensitive or Bench drill press
• Upright drill press
![Page 10: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/10.jpg)
Radial drill Press
• This is the largest drill press designed to drill up to 100-mm diameter holes in large workparts.
• It has a radial arm along which the drilling head can be moved and clamped.
![Page 11: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/11.jpg)
Other drilling machines• The gang drill is a drill press consisting of a series
of drill presses connected together in an in-line arrangement so that a series of drilling operations can be done in sequence.
• In the multiple-spindle drill, several drill spindles are connected together to drill multiple holes simultaneously into the workpart.
• Numerical control drill presses (CNC)are available to control the positioning of the holes in the workparts.
![Page 12: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/12.jpg)
4. Geometry of twist drill
• The twist drill is the most used cutting tools in the drilling operation.
Figure : Standard geometry of a twist drill
![Page 13: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/13.jpg)
• The twist drill is the most used cutting tools in the drilling operation.
• The twist drill is provided with two spiral grooves and two cutting edges.
• The chips produced are guided up through these spiral grooves.
• The grooves also serve as passage to the cutting fluid.
• In order that the cutting edges can cut off chips, two movements are required simultaneously; rotational speed and axial feed.
![Page 14: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/14.jpg)
• The typical helix angle of a general purpose twist drill is 18~30o while the point angle (which equals two times the major cutting edge angle) for the same drill is 118o.
• Some standard drill types are, straight shank: this type has a cylindrical shank and is
held in a chuck; taper shank: his type is held directly in the drilling
machine spindle.• Drills are normally made of HSS but carbide-tipped drills,
and drills with mechanically attached carbide inserts are commonly used in many operations, especially on CNC drilling machines.
![Page 15: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/15.jpg)
Cutting Drill angles • In twist drill, there are various angles to be considered: Cutting angle (ca) or angle of lip:
The two lips must be of same length and equal angle. For ordinary work, the cutting angle is 59º and vary with metal to metal.
Lip clearance angle:The cone shaped cutting end is the point from the lips and varies from 12- 15º degrees. In drilling soft materials, the angle may be increased under heavy feeds. For hard materials, the recommended angle is 9º degrees. If reduced further the drill cannot cut into the metal and may break in the centre along the web.
![Page 16: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/16.jpg)
Rake angle: It is the angle between the flute and the workpiece that is usually 70-75º degrees. This helps to secure the lip over the correct space to curl the chips. If more there will be no edge for cutting and if less the cutting edge will be too thin and may break under strain.
![Page 17: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/17.jpg)
5. Cutting conditions in drilling
• The twist drill is a cutting tool with two symmetrical opposite cutting edges, each removing part of the material in the form of chip.
• Fig. : Basics of a drilling operation.
![Page 18: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/18.jpg)
6. Motions of Drill and Cutting Velocity
• In drilling, the primary motion is the rotation of the cutting tool held in the spindle.
• Drills execute also the secondary feed motion.• Cutting velocity V in drilling is not a constant
along the major cutting edge as opposed to the other machining operations.
It is zero at the center of the twist drill, and has a maximum value at the drill corner.
The maximum cutting speed is given by:
![Page 19: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/19.jpg)
V = πDNwhere D is the drill diameter, and N is the rotational speed of the drill.
• As in the case of turning and milling, cutting speed V is first calculated or selected from appropriate reference sources, and then the rotational speed of the drill N, which is used to adjust drill press controls, is calculated.
![Page 20: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/20.jpg)
7. Feed in Drilling• Feed (f) is the distance that the drill penetrates
per revolution (mm/rev), the share of each cutting edge is = f/2
• Two types of feed in drilling can be identified: feed per tooth fz: has the same meaning as in the
other multi-tooth cutting tools.Feeds per tooth are roughly proportional to drill diameter, higher feeds for larger diameter drills.
• feed per minute fm: feed per minute is calculated taking into account the rotational speed N,
fm = 2fzN
![Page 21: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/21.jpg)
• Feed per minute is used to adjust the feed change gears.
• Depth of cut d is equal to the half of drill diameter, d = 1⁄2 D
where D is the drill diameter. • In core drilling, a drilling operation used to enlarge an
existing hole of diameter D(hole), depth of cut is given by
d = 1⁄2 (D(drill) – D(hole)) where D(drill) is the drill diameter, and D(hole) is the
diameter of the hole being enlarged.
![Page 22: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/22.jpg)
8. Drilling time
• Drilling time (T) can be given by the equation; T = L / f N;
Where f is the feed (mm/rev) N is the rotational speed (rpm) L is the sum of hole depth, approach and over travel distances.*The approach is usually considered as 0.4D while over travel ranges from 1 to 3mm.
![Page 23: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/23.jpg)
9. Drilling operations
![Page 24: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/24.jpg)
• Drilling is used to drill a round blind or through hole in a solid material. If the hole is larger than ~30 mm, its a good idea to drill a smaller pilot hole before core drilling the final one. For holes larger than ~50 mm, three-step drilling is recomended;
• Core drilling is used to increase the diameter of an existing hole.
• Step drilling is used to drill a stepped (multi-diameter) hole in a solid material.
![Page 25: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/25.jpg)
• Counterboring provides a stepped hole again but with flat and perpendicular relative to hole axis face. The hole is used to seat internal hexagonal bolt heads.
• Countersinking is similar to counterboring, except that the step is conical for flat head screws.
• Reaming provides a better tolerance and surface finish to an initially drilled hole. Reaming slightly increases the hole diameter. The tool is called reamer;
![Page 26: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/26.jpg)
• Center drilling is used to drill a starting hole to precisely define the location for subsequent drilling. The tool is called center drill. A center drill has a thick shaft and very short flutes. It is therefore very stiff and will not walk as the hole is getting started.
• Gun drilling is a specific operation to drill holes with very large length-to-diameter ratio up to L/D ~300. There are several modifications of this operation but in all cases cutting fluid is delivered directly to the cutting zone internally through the drill to cool and lubricate the cutting edges, and to remove the chips
![Page 27: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/27.jpg)
10. Reamers
• The reamer used in reaming operation has similar geometry as for twist drill .
• The difference in geometry between a reamer and a twist drill are:
The reamer contains four to eight straight or helical flutes, respectively cutting edges.
The tip is very short and does not contain any cutting edges.
![Page 28: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/28.jpg)
![Page 29: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/29.jpg)
11. Drill materials
• Drills are normally made of high-speed steel (HSS) but carbide-tipped drills, and drills with mechanically attached carbide inserts are commonly used in many operations, especially on CNC drilling machines
![Page 30: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/30.jpg)
12. Apparatus needed during drilling operation
• Normally, holes produced by drilling are bigger than the drill diameter and depending on its applications; the drilled holes will subjected to other operations such as reaming or honing to better surface finish and dimensional accuracy
• There are also several apparatus needed during the drilling operation as shown below:
Drilling machine Center punch Hammer Center drill Twist drills Coolant Vernier caliper Two flute drill set: i. Center drill; ii. Countersink drill; iii. Counter bore drill;
iv. Drill various diameter
![Page 31: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/31.jpg)
Part II. Welding Processes
![Page 32: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/32.jpg)
Welding Processes
Ship Structures
![Page 33: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/33.jpg)
1. INTRODUCTION
• Welding is the process of permanently joining two or more metal parts, by melting both materials. The molten materials quickly cool, and the two metals are permanently bonded.
• Modern welding technology started just before the end of the 19th century with the development of methods for generating high temperature in localized zones.
• Welding generally requires a heat source to produce a high temperature zone to melt the material, though it is possible to weld two metal pieces without much increase in temperature.
• Welding process can be done with or without the application of pressure, and with or without the use of filler metal.
![Page 34: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/34.jpg)
2. Classification of Welding
• Fusion Welding or Non-Pressure Welding The materials at the joint are heated to a molten
state and allowed to solidify.(Ex) Gas welding, Electric Arc welding
• Pressure Welding or Plastic Welding The piece of metal to be joined are heated to a
plastic state and forced together by external pressure.(Ex) Resistance welding
![Page 35: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/35.jpg)
Classification of Welding (Cont’)
Fusion Welding Pressure Welding
Homogeneous Heterogeneous
Brazing SolderingGas Welding
Electroslag
High Energy Beam
Electric Arc
MIGTIG
Shielded Metal Arc – “Stick”
Friction Welding
![Page 36: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/36.jpg)
2.1. Fusion Welding Principles
• Base metal is melted• Filler metal may be added• Heat is supplied by various means
– Oxyacetylene gas– Electric Arc– Plasma Arc– Laser
![Page 37: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/37.jpg)
Fusion Weld Zone
Fig : Characteristics of a typical fusion weld zone in oxyfuel gas and arc welding.
![Page 38: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/38.jpg)
Fusion Welding
BASE METAL
WELD
SOLIDIFIED SLAG
ARC POOL
WELDING ATMOSPHERE
CORE WIRE
ELECTRODE COATING
ARC STREAM
PENETRATION DEPTH
![Page 39: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/39.jpg)
Weld Metal Protection
• During fusion welding, the molten metal in the weld “puddle” is susceptible to oxidation
• Must protect weld puddle (arc pool) from the atmosphere
• Methods– Weld Fluxes– Inert Gases– Vacuum
![Page 40: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/40.jpg)
Weld Fluxes
• Typical fluxes– SiO2, TiO2, FeO, MgO, Al2O3
• Produces a gaseous shield to prevent contamination the oxygen and nitrogen of the air.
• Act as scavengers to reduce oxides.• Add alloying elements to the weld.• Influence shape of weld bead during
solidification.
![Page 41: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/41.jpg)
Inert Gases
• Argon, helium, nitrogen, and carbon dioxide• Form a protective envelope around the weld
area• Used in
– MIG– TIG– Shield Metal Arc
![Page 42: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/42.jpg)
Vacuum
• Produce high-quality welds• Used in electron beam welding• Nuclear/special metal applications
– Zr, Hf, Ti• Reduces impurities by a factor of 20 versus
other methods• Expensive and time-consuming
![Page 43: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/43.jpg)
3. Types of Fusion Welding
• Oxyacetylene Cutting/Welding• Shielded Metal Arc (“Stick”)• Metal Inert Gas (MIG) • Tungsten Inert Gas (TIG)
![Page 44: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/44.jpg)
3.1. Oxy-acetylene Arc Welding
• Flame formed by burning a mix of acetylene (C2H2) and oxygen
• Fusion of metal is achieved by passing the inner cone of the flame over the metal
• Oxyacetylene can also be used for cutting metals
Inner Cone: 5000-6300 deg F Combustion Envelope 3800 deg F
2300 deg FTORCH TIP
![Page 45: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/45.jpg)
Oxyacetylene flames
Fig : Three basic types of oxyacetylene flames used in oxyfuel-gas welding and cutting operations: (a) neutral flame; (b) oxidizing flame; (c) carburizing, or reducing flame. The gas mixture in (a) is basically equal volumes of oxygen and acetylene.
![Page 46: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/46.jpg)
Oxyacetylene flames• Oxygen is turned on, flame immediately changes into a long white inner area
(Feather) surrounded by a transparent blue envelope is called Carburizing flame (30000C)
• Addition of little more oxygen give a bright whitish cone surrounded by the transparent blue envelope is called Neutral flame (It has a balance of fuel gas and oxygen) (32000c)
Used for welding steels, aluminium, copper and cast iron• If more oxygen is added, the cone becomes darker and more pointed, while the
envelope becomes shorter and more fierce is called Oxidizing flame Has the highest temperature about 34000C Used for welding brass and brazing operation
![Page 47: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/47.jpg)
Oxyacetylene Torch
Fig. (a) General view of and (b) cross-section of a torch used in oxyacetylene welding. The acetylene valve is opened first; the gas is lit with a spark lighter or a pilot light; then the oxygen valve is opened and the flame adjusted. (c) Basic equipment used in oxyfuel-gas welding. To ensure correct connections, all threads on acetylene fittings are left-handed, whereas those for oxygen are right-handed. Oxygen regulators are usually painted green, and acetylene regulators red.
![Page 48: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/48.jpg)
3.2. Shielded Metal Arc (Stick)• An electric arc is generated between a coated
electrode and the parent metal• The coated electrode carries the electric current to
form the arc, produces a gas to control the atmosphere and provides filler metal for the weld bead
• Electric current may be AC or DC. If the current is DC, the polarity will affect the weld size and application
![Page 49: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/49.jpg)
Shielded Metal Arc (Stick)
Fig. Schematic illustration of the shielded metal-arc welding process. About 50% of all large-scale industrial welding operations use this process.
![Page 50: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/50.jpg)
Shielded Metal Arc (con’t)• Process:
– Intense heat at the arc melts the tip of the electrode– Tiny drops of metal enter the arc stream and are
deposited on the parent metal– As molten metal is deposited, a slag forms over the bead
which serves as an insulation against air contaminants during cooling
– After a weld ‘pass’ is allowed the cool, the oxide layer is removed by a chipping hammer and then cleaned with a wirebrush before the next pass.
![Page 51: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/51.jpg)
3.3. Inert Gas Welding
• For materials such as Al and its alloys or Ti which quickly form oxide layers. The shielded gases used are:
Argon, Helium, nitrogen, carbon dioxide or mixture of them.
Argon and Helium are completely inert and therefore they provide a complete inert atmosphere around the puddle.
![Page 52: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/52.jpg)
• Uses a consumable electrode (filler wire made of the base metal) and is fed automatically from a coil into the arc.
• Inert gas is typically Argon
Metal Inert Gas (MIG)
BASE METAL PUDDLE
POWER SOURCE
DRIVE WHEELSCONSUMABLE ELECTRODE
ARC COLUMNSHIELDING GAS
![Page 53: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/53.jpg)
• Tungsten electrode acts as a cathode• A plasma is produced between the tungsten cathode and the base
metal which heats the base metal to its melting point• Filler metal can be added to the weld pool
Tungsten Inert Gas (TIG)
BASE METAL PUDDLE
POWER SOURCE
ARC COLUMNSHIELDING GAS
TUNGSTEN ELECTRODE
+ +
BASE METAL (ANODE)
TUNGSTEN ELECTRODE
(CATHODE)
- - -+ +
![Page 54: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/54.jpg)
4. Submerged arc welding
Fig : Schematic illustration of the submerged-arc welding process and equipment. The unfused flux is recovered and reused .
![Page 55: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/55.jpg)
Submerged arc welding (Cont)
Fig : Simplified schematic illustration of the submerged-arc welding process
![Page 56: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/56.jpg)
Submerged arc welding (Cont)• Submerged arc welding (SAW) is an electric arc welding
process that uses a continuous, consumable bare wire electrode.
• The arc shielding is provided by a cover of granular flux.• The electrode wire is fed automatically from a coil into the
arc.• The flux is introduced into the joint slightly ahead of the weld
arc by gravity from a hopper.
![Page 57: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/57.jpg)
5. Flux cored Arc Welding
• Flux cored arc welding (FCAW) is similar to a gas metal arc welding (MIG).
• Electrode is tubular in shape and is filled with flux.
• Cored electrodes produce more stable arc, improve weld contour and produce better mechanical properties.
• Flux is more flexible than others.
![Page 58: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/58.jpg)
Equipment used in MIG and FCAW Welding Operations
Fig : Basic equipment used in gas metal-arc (MIG) and (FCAW) welding operations
![Page 59: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/59.jpg)
6. Plasma-Arc Welding Process
• Plasma Arc Welding (PAW) is a special form of gas tungsten arc welding in which a plasma arc is directed at the weld area.
• The tungsten electrode is contained in a specially designed nozzle that focuses a high-velocity stream of inert gas (for example, argon or argon-hydrogen mixtures, and helium) into the region of the arc to produce a high-velocity plasma jet of small diameter and very high-energy density.
• Temperatures in plasma arc welding reach 30,000o C or greater, hot enough to melt any known metal.
![Page 60: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/60.jpg)
Plasma-Arc Welding Process (Cont)
Fig.: Two types of plasma-arc welding processes: (a) transferred, (b) nontransferred. Deep and narrow welds can be made by this process at high welding speeds.
![Page 61: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/61.jpg)
7.Welding Positions
![Page 62: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/62.jpg)
8.Main Joint Design
BUTT JOINTBUTT JOINT
STRAP JOINT
LAP JOINT
FILLET JOINT
CORNER JOINT
![Page 63: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/63.jpg)
Derived Welding Joint Design
Fig. Examples of welded joints and their terminology.
![Page 64: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/64.jpg)
9. Resistance welding
• Resistance welding (RW) is a group of fusion welding processes that utilizes a combination of heat and pressure to accomplish coalescence.
• The heat required is generated by electrical resistance to current flow at the interface of two parts to be welded.
• The resistance welding processes of most commercial importance are spot and seam welding.
![Page 65: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/65.jpg)
9.1. Resistance Spot Welding• Resistance spot welding (RSW) is a resistance
welding process in which fusion of the base metal is achieved at one location by opposing electrodes.
• Resistance spot welding is widely used in mass production of automobiles, appliances, metal furniture, and other products made of sheet metal of thickness 3 mm or less.
![Page 66: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/66.jpg)
• The cycle in a spot welding operation consists of the steps depicted in the figure:
Steps in a spot welding cycle: (1) parts inserted between open electrodes, (2) electrodes close and force is applied, (3) weld time (current is switched), (4) current is turned off but force is maintained, and (5) electrodes are opened, and the welded assembly is removed.
![Page 67: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/67.jpg)
9.2. Resistance Seam Welding
• In Resistance Seam Welding (RSEW), the electrodes are two rotating wheels as shown in the figure:
![Page 68: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/68.jpg)
Different types of seam welding
Different types of seam welding, (from left to right) conventional seam welding, roll spot welding, continuous resistance seam welding.
![Page 69: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/69.jpg)
Different types of seam welding (Cont’)
• The spacing between the weld nuggets in resistance seam welding depends on the motion of the electrode wheels relative to the application of the weld current.
• In the usual method of operation, called continuous motion welding, the wheel is rotated continuously at a constant velocity, and current is turned on at timing intervals consistent with the desired spacing between spot welds along the seam so that overlapping weld spots are produced.
![Page 70: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/70.jpg)
Different types of seam welding (Cont’)
• But if the frequency of current switching is reduced sufficiently, there will be spacing between the weld spots, and this method is termed roll spot welding.
• In another variation, the welding current remains on at a constant level so that a truly continuous welding seam is produced.
![Page 71: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/71.jpg)
10. Generalized Welding Symbol
FAR SIDE DETAILS
ARROW SIDE DETAILS
Field weld symbol
Weld all-around for pipes, etc.
L1-L2
L1-L2
D = Weld Depth (usually equal to plate thickness)
L1 = Weld Length
L2 = Distance between centers for stitched welds
The Field Weld Symbol (generally used in arc welding)is a guide for installation. Shipyards normally do not use it, except in modular construction.
ElectrodeMaterial
D
D
Weld Geometry
![Page 72: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/72.jpg)
Example Welding Symbol
1/2” 1/2”
1/2
1/2
One-sided welds are max 80% efficientTwo sided are 100% efficient
Geometry symbol for V-groove
![Page 73: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/73.jpg)
Weld Symbols (Butt Joints)
Backing
![Page 74: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/74.jpg)
Weld Symbol (Fillet Joints)
![Page 75: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/75.jpg)
Weld Symbol (Corner Joints)
![Page 76: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/76.jpg)
General Design Guidelines
![Page 77: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/77.jpg)
11. Electrode Designations
![Page 78: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/78.jpg)
Weld Quality and Testing in Arc Welding
![Page 79: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/79.jpg)
1. WELD QUALITY
• Welding discontinuities can be caused by inadequate or careless application.
• The major discontinuities that affect weld quality are: Porosity Slag Inclusions Incomplete fusion and penetration Weld profile Lamellar tears Cracks Surface damage Residual stresses
![Page 80: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/80.jpg)
Discontinuities and Defects in Fusion Welds
Fig.1. Examples of various discontinuities in fusion welds.
![Page 81: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/81.jpg)
Fig.2. Schematic illustration of various defects in fusion welds.
![Page 82: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/82.jpg)
1.1. Porosity• Caused by gases released during melting of the weld area but
trapped during solidification, chemical reactions, Contaminants
• They are in form of spheres or elongated pockets.• Porosity can be reduced by Proper selection of electrodes Improved welding techniques Proper cleaning and prevention of contaminants Reduced welding speeds
![Page 83: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/83.jpg)
1.2. Slag Inclusions
• Compounds such as oxides ,fluxes, and electrode-coating materials that are trapped in the weld Zone.
• Prevention can be done by following practices : Cleaning the weld bed surface before the next layer
is deposited. Providing enough shielding gas. Redesigning the joint.
![Page 84: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/84.jpg)
1.3. Incomplete Fusion and Penetration
• Produces lack of weld beads• Practices for better weld : Raising the temperature of the base metal. Cleaning the weld area, prior to the welding. Changing the joint design and type of electrode. Providing enough shielding gas.
![Page 85: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/85.jpg)
1.4. Penetration
• Incomplete penetration occurs when the depth of the welded joint is insufficient.
• Penetration can be improved by the following practices :
Increasing the heat Input. Reducing the travel speed during the welding. Changing the joint design. Ensuring the surfaces to be joined fit properly.
![Page 86: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/86.jpg)
1.5. Weld Profile
• Under filling results when the joint is not filed with the proper amount of weld metal.
• Undercutting results from the melting away of the base metal and consequent generation of a groove in the shape of a sharp recess or notch.
• Overlap is a surface discontinuity usually caused by poor welding practice and by the selection of improper material.
![Page 87: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/87.jpg)
1.6. Cracks
• Cracks occur in various directions and various locations
• Factors causing cracks:
Temperature gradients that cause thermal stresses in the weld zone.
Variations in the composition of the weld zone. Embrittlement of grain boundaries Inability of the weld metal to contract during
cooling.
![Page 88: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/88.jpg)
Types of cracks
Fig : Types of cracks (in welded joints) caused by thermal stresses that develop during solidification and contraction of the weld bead and the surrounding structure. (a) Crater cracks (b) Various types of cracks in butt and T joints.
![Page 89: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/89.jpg)
1.7. Lamellar tears• Occurred due to the shrinkage of the restrained
components in the structure during cooling.• Can be avoided by providing for shrinkage of the
members.• Changing the joint design. • Surface Damage : These discontinuities may
adversely affect the properties of welded structure, particularly for notch sensitive metals.
![Page 90: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/90.jpg)
1.8. Residual Stresses
• Caused because of localized heating and cooling during welding, expansion and contraction of the weld area causes residual stresses in the work piece.
• Distortion, Warping and buckling of welded parts• Stress corrosion cracking• Further distortion if a portion of the welded
structure is subsequently removed• Reduced fatigue life
![Page 91: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/91.jpg)
1.9. Distortion of Parts After Welding
Fig. Distortion of parts after welding. (a) Butt joints and (b) fillet welds. Distortion is caused by differential thermal expansion and contraction of different regions of the welded assembly.
![Page 92: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/92.jpg)
2. Weld Testing2.1. Destructive Techniques
Fig. Destructive Techniques: (a) Specimen for longitudinal tension-shear testing; (b) specimen for transfer tension-shear testing; (c) wraparound bend test method; (d) three-point bending of welded specimens.
![Page 93: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/93.jpg)
2.2. Non-Destructive testing
• Often weld structures need to be tested Non-Destructively
• Non-Destructive testing are : Visual Liquid-penetrant Radiographic Magnetic-particle Ultrasonic
![Page 94: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/94.jpg)
![Page 95: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/95.jpg)
Part 3: Turning operations
![Page 96: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/96.jpg)
1. Introduction• Turning is a machining process to produce parts
round in shape by a single point tool on lathe Machines.
• The cutting tool is fed either linearly in the direction parallel or perpendicular to the axis of rotation of the workpiece, or along a specified path to produce complex rotational shapes.
• The primary motion of cutting in turning is the rotation of the workpiece, and the secondary motion of cutting is the feed motion of the cutting tool (See figure on the next slide).
![Page 97: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/97.jpg)
2. Principal Surfaces and Motions
![Page 98: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/98.jpg)
3. Cutting conditions in turning
• Cutting speed in turning V in m/s is related to the rotational speed of the workpiece by the equation:
V = πDN (m/sec)where D is the diameter of the workpiece, m; N is the rotational speed of the workpiece, rev/s (rpm).
• Feed in turning is generally expressed in mm tr-1 (millimetres per revolution).
![Page 99: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/99.jpg)
• The turning operation reduces the diameter of the workpiece from the initial diameter Do to the final diameter Df. The change in diameter is actually two times depth of cut, d:
2d = Do - Df• The volumetric rate of material removal (so-
called material removal rate, mrr) is defined bymrr = Vfd
• When using this equation, care must be exercised to assure that the units for V are consistent with those for f and d.
![Page 100: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/100.jpg)
4. Operations in turning
• Turning of cylindrical surfaces• Turning of flat surfaces• Threading• Form turning• Knurling• Drilling, Internal grooving and Boring
![Page 101: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/101.jpg)
4.1. Turning of cylindrical surfaces
The lathe can be used to reduce the diameter of a part to a desired dimension. The resulting machined surface is cylindrical.
![Page 102: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/102.jpg)
4.2. Turning of flat surfaces
A lathe can be used to create a smooth, flat face very accurately perpendicular to the axis of a cylindrical part.
Tool is fed radially or axially to create a flat machined surface.
![Page 103: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/103.jpg)
4.3. Threading Threading is turning operation on lathe machine to
cut an helical groove on or in the workpiece, which is actually a thread, by The single-point cutting tool at a feed exactly equal to the thread pitch.
The procedure calls for correct settings of the machine, and also that the helix be restarted at the same location each time if multiple passes are required to cut the entire depth of thread.
The tool point must be ground so that it has the same profile as the thread to be cut.
![Page 104: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/104.jpg)
Another possibility is to cut threads by means of a thread die (external threads), or a tap (internal threads). These operations are generally performed manually for small thread diameters.
![Page 105: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/105.jpg)
4.4. Form turning
Cutting tool has a shape that is imparted to the workpiece by plunging the tool into the workpiece.
In form turning, cutting tool is complex and expensive but feed is linear and does not require special machine tools or devices.
![Page 106: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/106.jpg)
![Page 107: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/107.jpg)
4.5. Contour turning (profiling)
Cutting tool has a simple shape, but the feed motion is complex; cutting tool is fed along a contour thus creating a contoured shape on the workpiece.
For profiling, special lathes* or devices are required.
Producing tapers on a lathe is a specific task and contour turning is just one of the possible solutions**.
![Page 108: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/108.jpg)
![Page 109: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/109.jpg)
4.6. Drilling, Internal grooving and Boring
![Page 110: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/110.jpg)
4.7. Knurling
This is not a machining operation at all, because it does not involve material removal. Instead, it is a metal forming operation used to produce a regular crosshatched pattern in the work surface.
![Page 111: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/111.jpg)
![Page 112: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/112.jpg)
5. Lathes
• A lathe is a machine tool that rotates the workpiece against a tool whose position it controls.
• The spindle (see picture in the next page) is the part of the lathe that rotates. Various work holding attachments such as three jaw chucks, collets, and centers can be held in the spindle. The spindle is driven by an electric motor through a system of belt drives and gear trains.
• Spindle rotational speed is controlled by varying the geometry of the drive train.
![Page 113: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/113.jpg)
6. Principal components of a lathe
![Page 114: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/114.jpg)
• The tailstock can be used to support the end of the workpiece with a center, or to hold tools for drilling, reaming, threading, or cutting tapers.
• The carriage controls and supports the cutting tool. It consists of:
a saddle that slides along the ways;an apron that controls the feed mechanisms;a cross slide that controls transverse motion of the tool;a tool post that holds the cutting tools.
![Page 115: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/115.jpg)
7. Work holding methods in lathes
![Page 116: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/116.jpg)
8. Turning tapers on lathes
• A taper is a conical shape.
• The tailstock offset h is defined by h = Lsinα
where L is the length of workpiece, and α is the half of the taper angle.
![Page 117: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/117.jpg)
9. Cutting tools
![Page 118: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/118.jpg)
Left and Right-hand turning tool bit
![Page 119: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/119.jpg)
Shapes of Tool Bits
![Page 120: Workshop practice ii lecture notes](https://reader034.fdocuments.in/reader034/viewer/2022042520/5872310b1a28ab3b7a8b7a8f/html5/thumbnails/120.jpg)
END OF PART 3
THANK YOU