Wobd2 how to setup v4.94 digiprog3

5
How to Setup V4.94 Digiprog3 Mileage Correction Tool V4.94 digiprog 3 odometer programmer is the newest version of Digiprog3, which adds more car models on the basic of V4.888. Digiprog III is a cost-effective mileage correction tool supporting multi-language and full range of vehicle. Here is the instruction of Digiprog 3 odometer mater setup. 1. Connect the Digiprog 3 main unit to the OBD diagnostic socket, but do not use the cigar lighter lead. Otherwise, it will lose the warranty. 2. After well connection with vehicle, the Digirog 3 main unit will power on, and the device is loading the system. 3 Then the device screen will display Digiprog III software (free download) version information. Software is marked as unique 12 digit electronic serial number. 4. When your Digiprog 3 has finished loading an information screen will appear with a disclaimer regarding the use of the machine. 5. Click “Check/Tick” button to start using Digiprog 3 odometer correction tool.

Transcript of Wobd2 how to setup v4.94 digiprog3

Page 1: Wobd2 how to setup v4.94 digiprog3

How to Setup V4.94 Digiprog3 Mileage Correction Tool

V4.94 digiprog 3 odometer programmer is the newest version of Digiprog3, which adds more

car models on the basic of V4.888. Digiprog III is a cost-effective mileage correction tool

supporting multi-language and full range of vehicle. Here is the instruction of Digiprog 3

odometer mater setup.

1. Connect the Digiprog 3 main unit to the OBD diagnostic socket, but do not use the cigar lighter

lead. Otherwise, it will lose the warranty. 

2. After well connection with vehicle, the Digirog 3 main unit will power on, and the device is

loading the system. 

3 Then the device screen will display Digiprog III software (free download) version information.

Software is marked as unique 12 digit electronic serial number.

4. When your Digiprog 3 has finished loading an information screen will appear with a disclaimer

regarding the use of the machine.

5. Click “Check/Tick” button to start using Digiprog 3 odometer correction tool. 

Page 2: Wobd2 how to setup v4.94 digiprog3

6. The digiprog 3 will require password to enter the system. The default password is “1”. 

7. Welcome the main interface. You are also allowed to check the software marked red on the

picture below. 

Page 3: Wobd2 how to setup v4.94 digiprog3

8. Select the function you need to do and follow the screen instruction. 

Note:The V4.94 digiprog 3 comes with ST01 or ST04 cable, so you do not have to buy extra cable if

your ST01/ ST04 cable is available.. 

 

Digiprox 3 adapter list:http://www.wobd2.com/upload/pro/4147-digiprog3-adapter-list.pdf

Page 4: Wobd2 how to setup v4.94 digiprog3

Digiprog III Odometer Programmer Software Free Download:http://down.wobd2.com/digiprog3-manual.part1.ziphttp://down.wobd2.com/digiprog3-manual.part2.zip

A regulated 12V power supply should be used to power your digiprog III. If power up by above

13.5V is used to power the machine, damage may be caused to the main circuit board and it will

need to be sent to your Digiprog III dealer for repair.

V4.94 digiprog 3 odometer programmer

http://www.wobd2.com/wholesale/newest-v494-digiprog-iii-digiprog3-odometer-master-

programmer-entire-kit-4147.html

adds more car models

http://www.wobd2.com/upload/pro/v494-digiprog-iii-vehicle-list.pdf

ST01/ ST04 cable

http://www.wobd2.com/wholesale/st04-for-cable-digiprogiii-2764.html