WIRELESS Solar Energy Monitor - Jaycar Watts Clever WIRELESS Solar Energy Monitor helps you conserve...

WIRELESSSolar Energy MonitorMonitor household electricity use

Instruction ManualEW4009

The Watts Clever WIRELESS Solar Energy Monitor helps you conserve elec-tricity by showing you how much you use, and what it costs, as you use it where by it monitor the energy produced by your Solar System in real-time. This feedback will help you take steps to reduce your energy consumption and save money. The WIRELESS Solar Energy Monitor will show you:

● Your current electricity usage.

● The performance of your off-grid or grid-tied Solar Electric System.

● Your accumulated electricity usage over any time period.

● Your accumulated power generated by Solar System over any time period.

● Your estimated per hour usage.

● Your electricity cost per hour.

● Your accumulated electricity cost over an hour, a day, or ant time period.

● Your estimated monthly bill.

● The money you redeem from Solar Bonus Scheme.

Welcome

And when you program the WIRELESS Solar Energy Monitor with your electric-ity billing rates, it will show you:

Notes on Safety

Caution ● Please read all instructions before you use the monitoring system.

● Please shake the Energy Monitor and the Power Transmitter first before installation. In case you hear any sound from inside of the part, please don’t use it. Please replace it with your reseller.

● Keep the Energy Monitor, Power Transmitter and Sensor Clamp away from sources of heat, water or any other liquid.

● Do not locate the Energy Monitor, Power Transmitter and Sensor Clamp within reach of children.

● Do not open the product other than to replace the batteries.

● Do not use the monitoring system if you find your electric wire in abnormal conditions, such as loose wire, exposed copper wire, burnt mark on wire insulation layer, holes on wire layer or damage on electric meter. In case of such abnormalities, please consult a professional electrician immediately.

● Periodically check all wires and components to ensure there is no damage.

● Use a dry cloth to clean. Don’t use solvent, abrasive cleaners or water.

● Do not reply on the displayed information to calculate the cost of your elec-tricity bill. The WIRELESS Solar Energy Monitor is an educational device and is NOT intended to replace your energy supplies energy meter.

● Do not use this product where the use of radio frequency products can cause malfunction in other equipment (for instance hospitals, aircraft, etc.).

● Do not dispose of old batteries in a fire as they may explode.

● Do not open or mutilate the batteries. Released electrolyte from the bat-teries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

● Always insert batteries correctly with regard to polarity (+ and -) marked on the battery and the equipment.

● Do not short battery terminals.

● Do not mix old and new batteries. Replace all of item at the same time with new batteries of the same brand and type.

● Remove dead batteries immediately and follow local codes for disposal.

2 3

Contents of the box

* 10mm clamp or

* 25mm clamp

Energy Monitor 2 x Power Transmitter (2 x C Cells included) with sensor clamp

(For Home Electricity System & Solar System)

Wall Sticker for Power Transmitter

* RJ45-USBData Cable (3M)

3 x AAA Batteries Power adapter

Thank you for your purchasing WIRELESS Solar Energy Monitor. Please verify that your package contains all of the components shown below.

If any item is missing. Please contact your reseller immediately.

* Optional accessories are available to purchase online and your reseller. (Please visit www.wattsclever.com)

Contents

4

5

6

15

17

18

19

20

21

22

23

24

26

28

30

32

33

34

35

Contents of the box

Parts

Setup

1 Full LCD Display Layout

2 Settings before start

3 Pairing for entire house use

4 Installation of the Power Transmitter for entire house use

5 Pairing for Solar System use

6 Installation of the Power Transmitter for Solar System use

10 Mode of Energy Monitor

1 HOUSE COST Mode

2 HOUSE COST History Mode

3 HOUSE ENERGY Mode

4 HOUSE ENERGY History Mode

5 SOLAR ENERGY Mode

6 SOLAR ENERGY History Mode

7 COST BALANCE Mode

8 COST BALANCE History Mode

9 ENERGY BALANCE Mode


Reset of Energy Monitor

Resetting and Data Clearance

Buzzer Mode of Energy Monitor

Buzzer Mode

RJ45-USB Data Cable and Software


Tips for use

How electricity is measured

Find out the electric Power of your country 4 5

Setup

2 Settings before startYou have to finish below required settings before you start to use, other-wise the Energy Monitor will not work probably.

The required settings will finish the settings for YEAR / MONTH / DAY / TIME / VOLTAGE / CURRENCY / TARIFF continually in the order as described.

Step 1 • Power ON the Energy Monitor

Step 2 • Setting Mode - Setup for Current YEAR

Fig. 1

After being powered ON, the LCD screen will display (as Fig. 1) for about 3 seconds. This full LCD Display means Energy Monitor is in Setting Mode.

The display will shown the default setting for the year is [ 2011 ] and the symbol [ Y ] is flashing (Fig. 2). Now press the [ Set button1] shortly.

Fig. 2

The thousand - digit will flash. Then use [ Up button2] or [ Down button 3] to adjust the thousand - digit to the correct value for the year.

Parts

Set button1

Up button2 Down button3

Display

LED light

Setup

1 Full LCD Display Layout

Battery status icon:Tx for Power Transmitter of home consumptionSx for Power Transmitter of Solar System

Support 7 currencies:£ / € / R / $ / R$ / KR / Rs

Time indicator Support up to 3 Tariffs

Titles of displays

Specific symbol for display titles

All units to be used in the displays

Symbol of Negative

value

Clock and Channel No. Temperature

Solar iconSignal strength

Sensor clamp No.

6 7Continue setting on the next page.

LED light

Pairing hole Wall Sticker

Front Back

Setup

Press the [ Set button1] shortly and operate the same way as for the YEAR setting to finish the setting of the month value (range 01 - 12).

Step 4 • Setting Mode - Setup for the DAY

After you press [ Down button3] to confirm the setting of MONTH and then will enter into day setting interface. The default setting is [ 01 ] and the symbol [ D ] is flashing (Fig. 5).

Fig. 5

Press the [ Set button1] shortly and operate the same way as for the YEAR setting to finish the setting of the day value (range 01 - 31).

To confirm the setting of MONTH, press [ Down button3].

To modify the MONTH, please press the [ Set button1] again to re-start the MONTH setting.

To confirm the setting of DAY, press [ Down button3].

To modify the DAY, please press the [ Set button1] again to restart the DAY setting.

Setup

Press [ Set button1] to confirm and you will see that the hundred - digit of the year begins to flash.

Do the same way until you set the correct value of the last single - digit.

After you set the last single - digit, press the [ Set button1] shortly to confirm. The confirmation of the last single digit will make the complete 4 digits number flash (Fig. 3).

Step 3 • Setting Mode - Setup for the MONTH

After you press [ Down button3] to confirm the setting of YEAR and then will enter into month setting interface. The default setting is [ 01 ] and the symbol [ M ] is flashing (Fig. 4).

To confirm the setting of YEAR, press [ Down button3].

Fig. 3

To modify the YEAR, please press the [ Set button1] again to restart the YEAR setting.

Fig. 4


Setup

Step 6 • Setting Mode - Setup for the VOLTAGE

After you press [ Down button3] to confirm the setting of TIME and then will enter into voltage setting interface, where you will find three dashes to be set as the correct voltage value (Fig. 7).

Fig. 7

Press the [ Set button1] shortly and the dashes [ - - - ] will automatically turn to be [ 0 0 0 ] and then the hundred-digit will flash

Use [ Up button2] or [ Down button3] to adjust the hundred - digit to the correct value for the voltage. Then press the [ Set button1] shortly to confirm and do the same way until you set the correct value for the last-digit.

After you set the last single - digit, press the [ Set button1] shortly to confirm. The confirmation of the last single digit will make the complete voltage value flash (Fig. 8).

The voltage are generally in the range 100-240V. Check carefully the voltage level of your country before set up.

Setup

Step 5 • Setting Mode - Setup for the TIME

After you press [ Down button3] to confirm the setting of DAY and then will enter into time setting interface. The symbol [ ] is flashing (Fig. 6).

Fig. 6

Press the [ Set button1] shortly, the hour value of the clock will flash. Use the [ Up button2] or [ Down button3] to adjust to the correct hour.

Then press the [ Set button1], the time value will flash. Use the [ Up but-ton2] or [ Down button3] to adjust to the correct minute.

To confirm the setting of TIME, press [ Down button3].

To modify the TIME, please press the [ Set button1] again to restart the TIME setting.


Fig. 8

To modify the VOLTAGE, please press the [ Set button1] again to re-start the VOLTAGE setting.

To confirm the setting of VOLTAGE, press [ Down button3].

Setup

Use [ Up button2] or [ Down button3] to adjust the first digit to the correct value, then press the [ Set button1] shortly to confirm and do the same way until you set the correct value for the last digit and press the [ Set button1] to confirm for the rate of TARIFF 1.

● No matter the applied tariff is single tariff or 3 tariff, the tariff setting will go through tariff 1 to tariff 3 accordingly.

● For single tariff, please enter [ 00:00 ] as the starting time of tariff 1.

● Please only enter the starting time of every tariff.

The confirmation of the last digit will make the clock value [ - - : - - ] flash. The starting time for TARIFF 1 will be set next.

Press the [ Set button1] shortly to enter the location setting of decimal point. Use the [ Up button2] or [ Down button3] to adjust the deci-mal point to the correct location, and press the [ Set button1] shortly to confirm.

Setup

Step 7 • Setting Mode - Setup for the CURRENCY

After you press [ Down button3] to confirm the setting of VOLTAGE and then will enter into currency setting interface. Totally there are 7 kinds of currencies [ £ / € / R / $ / R$ / KR / Rs ] that can be selected (Fig. 9).

Fig. 9

Press the [ Set button1] shortly and the first currency will flash. Use the [ Up button2] or [ Down button3] to adjust to the correct currency.

Press the [ Set button1] shortly again to confirm the currency.

To modify the CURRENCY, please press the [ Set button1] again to restart the CURRENCY setting.

Step 8 • Setting Mode - Setup for the TARIFF

After you confirm the currency (eg. $ ), press [ Down button3] to enter into TARIFF setting interface, where you will find the default tariff value is displayed as [ $ - . - - - ], the time value is [ - - : - - ] and the symbol [ ] is flashing behind [ TARIFF ] as (Fig. 10). It means TARIFF 1 will be set first.

Fig. 10

To confirm the setting of CURRENCY, press [ Down button3].


Setup

Step 9 • Setting Mode - Setup for the Solar TARIFF

Step 10 • Complete Setting Mode of Energy Monitor

The last pressing of the [ Down button3] will finish the all the setting and the LCD screen will return to unpaired HOUSE COST Mode (as Fig. 13).

To enter into the Setting Mode from the HOUSE COST Mode

1. Press the [ Set button1] for about 3 seconds. The LCD screen will display full LCD Display.

2. After the LED light flashes twice, release the [ Set button1] and the LCD screen will enter into the Setting Mode.

Do the same way to set TARIFF 1 and press the [ Set button1] to con-firm the setting for of Solar TARIFF.

Fig. 13 HOUSE COST Mode

After you set the tariff, press [ Down button3] to enter into Solar TARIFF setting interface, where you will find the default tariff value is displayed as [ $ - . - - - ] and the decimal point is flashing as (Fig. 12). It means Solar TARIFF will be set.

Fig. 12

Setup

Press the [ Set button1] shortly, the hour value of the clock will flash. Use the [ Up button2] or [ Down button3] to adjust to the correct hour (range: 00-23).

Then press the [ Set button1] shortly to confirm and the minute value will flash. Use the [ Up button2] or [ Down button3] to adjust to the correct minute (range: 00-59).

Fig. 11

Press the [ Set button1] to confirm the starting time of TARIFF 1. The display will then automatically lead to setting interface of TARIFF 2 (as Fig. 11), follow by TARIFF 3. Please operate the setting same way as Setting of Tariff 1. symbol [ ] is flashing behind [ TARIFF ].

● For single tariff, you can set any starting time for TARIFF 1 or just leave the dashes unchanged go to (Step 9 • Setting Mode - Setup for the Solar TARIFF).

● For 3 tariff, you have to set the starting time according to the real case. And do the same way to set TARIFF 2 and TARIFF 3 as the set-ting of TARIFF 1.

14 15

Setup

When the pairing is successfully finished, the antenna icon stops flash-ing and stays on the top right corner of the LCD screen. The paired LCD screen will return to the HOUSE COST Mode (as Fig. 15). In case the Power Transmitter begins to send data, the HOUSE COST Mode will show the data accordingly.

The pairing may take up to 60 seconds.

To pair more Power Transmitters with the Energy Monitor, operate the same way as described above.

PAIREDFig. 15

successfulUnsuccessful

If the pairing can’t be finished successfully within one minute, the LCD screen will return to unpaired HOUSE COST Mode.

Setup

3 Pairing for entire house useStep 1 • Prepare for Energy Monitor

Step 2 • Prepare for Power Transmitter

In the HOUSE COST Mode (Fig. 13), press the [ Down button3] and hold it there for about 3 seconds when the antenna icon is flashing at the top right corner of the LCD screen. This means the Energy Monitor is ready for pairing.

Pull out the clear plastic tab (marked with “REMOVE BEFORE USING”) from the back of the Power Transmitter. The tab is an insulation sheet, once it is pulled out, the built-in batteries will make the Power Transmitter start to work immediately.

Keep the Power Transmitter as close to the Energy Monitor as possible. Use a slim stick to push into the pairing hole of the Power Transmitter (as Fig. 14) and hold it there until the LED light of the Power Transmitter flashes quickly. The Power Transmitter is now starting to pair with the Energy Monitor. Fig. 14

Press for 3 sec

1716 Continue pairing on the next page.

Setup

5 Pairing for Solar System useStep 1 • Prepare for Energy Monitor

Step 2 • Prepare for Power Transmitter

From the HOUSE COST Mode, press the [ Set button1] 2 TIMES to switch to the SOLAR ENERGY Mode (as Fig. 17).

Now press the [ Down button3] and hold it there for about 3 seconds when the antenna icon is flashing at the top right corner of the LCD screen. This means the Energy Monitor is ready for pairing.

Pull out the clear plastic tab (marked with “REMOVE BEFORE USING”) from the back of the Power Transmitter. The tab is an insulation sheet, once it is pulled out, the built-in batteries will make the Power Transmitter start to work immediately.

Keep the Power Transmitter as close to the Energy Monitor as possible. Use a slim stick to push into the pairing hole of the Power Transmitter (as Fig. 18) and hold it there until the LED light of the Power Transmitter flashes quickly. The Power Transmitter is now starting to pair with the Energy Monitor. Fig. 18

Press for 3 sec

2Fig. 17 SOLAR ENERGY ModePress 2 TIMES

Setup

4 Installation of the Power Transmitter for entire house use

OR

Fig. 16

You may choose to put the Power Transmitter in a dry place near the moni-tored object or stick the Power Transmitter on the wall near the monitored object.

The Sensor Clamp immediately starts to sensor the current and the moni-toring system starts to work.

Fix the Sensor Clamp

3-phase power supply

Fix the Sensor Clamp around the live cable of the monitored object, as be-low (Fig. 16) is shown (Don’t fix the clamp around the ground wire). Make sure the cable is passing through the clamp.

25mm ver.10mm ver.

If the monitored object use a 3-phase power supply. You need two more sensor clamps (available to purchase on our webshop and your reseller. Please visit www.wattsclever.com).

Connect the DC plug of each sensor clamp into the DC sockets on the back of the Power Transmitter.

0 7 4 2

kWh

METRE

1 6

1918 Continue pairing on the next page.


1 HOUSE COST ModeThe HOUSE COST Mode is what the user usually sees from the LCD screen of the Energy Monitor.

It is the forecast of next hour’s total electricity cost of all channels based on current power under consumption. The TARIFF No. will always display on the LCD screen and automatically reflect the applied tariff for current period.

The change of the power consumption will change the forecast of next hour’s cost.

Press the [ Up button2] or [ Down button3] from the HOUSE COST Mode will allow the user to view the HOUSE COST for channel 3 to channel 15 (as Fig. 22). In that case, the clock icon and numbers will be replaced by the channel number.

10 seconds idleness on each channel display will return the LCD screen to HOUSE COST Mode.

No key operation under any other displays will return the LCD screen to the COST Mode.

10 secidleness

Fig. 22

HOUSE COST Mode

Setup

When the pairing is successfully finished, the antenna icon stops flash-ing and stays on the top right corner of the LCD screen. The paired LCD screen will return to the HOUSE COST Mode (as Fig. 19).

The pairing may take up to 60 seconds.

PAIREDFig. 19

6 Installation of the Power Transmitter for Solar System use

Fig. 21

Fig. 20

You may choose to put the Power Transmitter in a dry place near the moni-tored object or stick the Power Transmitter on the wall near the monitored object.

The Sensor Clamp immediately starts to sensor the current and the moni-toring system starts to work.

Fix the Sensor Clamp

Fix the Sensor Clamp around the live cable coming out from the inventer to the electricity meter as below (Fig. 20) is shown. Make sure the cable is passing through the clamp (Fig. 21).

Inverter

Home ElectricityElectricity Meter

PowerTransmitter

Solar Panel

2120


3 HOUSE ENERGY ModeFrom the HOUSE COST Mode, shortly press the [ Set button1] ONCE to switch to the HOUSE ENERGY Mode (as Fig. 25), which displays the cur-rent power under consumption for channel 2.

Fig. 25Press ONCE

HOUSE ENERGY Mode

10 secidleness

Fig. 26

Press the [ Up button2] or [ Down button3] from the ENERGY Mode will allow the user to view the power consumption for channel 3 to channel 15 (as Fig. 26). In that case, the clock icon and numbers will be replaced by the channel number.

10 seconds idleness on each channel display will return the LCD screen to ENERGY Mode of all channels.

1

There are two units (watts and kW) involved in this Mode. For data equal to or below 999.9 watts, the unit displayed is watts, for data over 999.9 watts, the unit will automatically switch to kW (Fig. 26).


Press for 3 sec

2 HOUSE COST History Mode

Fig. 23

In Fig. 23, there are three kinds of cost history data automatically switch-ing among each other in an interval of 5 seconds.

From Fig. 22, press the [ Up button3] for about 3 seconds will lead the display screen to enter HOUSE COST History Mode (Fig. 23).

TODAY

MTD

YTD

● the money spent from 00:00 of current day to now.

● the money spent from 00:00 1st of current month to now.

● the money spent from 00:00 1st January of current year to now.

Cost data of a specific day

To view the cost data of an exact day, from the HOUSE COST History Mode, press the [ Up button2] for about 3 seconds until the display enter into the history date input interface (as Fig. 24).

The numbers before the decimal point is for month and the numbers after the decimal point is for day.

Fig. 24

Use the [ Up button2] or [ Down button3] and the [ Set button1] to select the date. Press [ Set button1] will make the selected date flash.

Then press the [ Down button3] to display the money spent for the se-lected date.

Press for 3 sec

2322

Press for 3 sec

2


5 SOLAR ENERGY ModeFrom the HOUSE COST Mode, shortly press the [ Set button1] 2 TIMES to switch to the SOLAR ENERGY Mode (as Fig. 29), which displays the output power of the Solar System (channel 1).

Fig. 29

Fig. 30

Press 2 TIMES

In Fig. 30, there are three kinds of balance history data automatically switching among each other in an interval of 5 seconds.

From Fig. 29, press the [ Up button3] for about 3 seconds will lead the display screen to enter SOLAR ENERGY History Mode (Fig. 30).

TODAY

MTD

YTD

● the electricity produced already by Solar from 00:00 of current day to now.

● the electricity produced already by Solar from 00:00 1st of cur-rent month to now.

● the electricity produced already by Solar from 00:00 1st Janu-ary of current year to now.

6 SOLAR ENERGY History Mode


4 HOUSE ENERGY History Mode

Fig. 27

In Fig. 27, there are three kinds of energy history data automatically switching among each other in every 5 seconds.

From Fig. 26, press the [ Up button3] for about 3 seconds will lead the display screen to enter HOUSE ENERGY History Mode (Fig. 27).

Press for 3 sec

Energy consumption data of a specific day

To view the energy consumption data of an exact day, from the HOUSE ENERGY History Mode, press the [ Up button2] for about 3 seconds until the display enter into the history date input interface (as Fig. 28).


Fig. 28


Then press the [ Down button3] to display the electricity spent for the selected date.

Press for 3 sec

TODAY

MTD

YTD

● the electricity consumption from 00:00 of current day to now.

● the electricity consumption from 00:00 1st of current month to now.

● the electricity consumption from 00:00 1st January of current year to now.

2524

Press for 3 sec

3


7 COST BALANCE Mode

8 COST BALANCE History Mode

From the HOUSE COST Mode, shortly press the [ Set button1] 3 TIMES to switch to the COST BALANCE Mode (as Fig. 32), which displays the bal-ance forecast between the HOUSE COST and SOLAR Yield for next hour based on current power. In case the SOLAR Yield is lower than HOUSE COST, the negative value symbol [ – ] will appear.

Fig. 32

Fig. 33

Press 3 TIMES


From Fig. 32, press the [ Up button3] for about 3 seconds will lead the display screen to enter COST BALANCE History Mode (Fig. 33).

TODAY

MTD

YTD

● the balance of energy cost from 00:00 of current day to now.

● the balance of energy cost from 00:00 1st of current month to now.

● the balance of energy cost from 00:00 1st January of current year to now.


History data of solar electricity output of a specific day

To view the history data of solar electricity output of an exact day, from the SOLAR ENERGY History Mode, press the [ Up button2] for about 3 sec-onds until the display enter into the history date input interface (as Fig. 31).


If you want to view the history data of an exact month, just input the day value as 00 after the month value and confirm.

The historical data of an exact day is available for the past 31 days. The historical data of a specific month is available for the past 12 months.

Fig. 31


Then press the [ Down button3] to display the electricity produced by solar for the selected date.

Press for 3 sec

2726

4



10 ENERGY BALANCE History Mode

From the HOUSE COST Mode, shortly press the [ Set button1] 4 TIMES to switch to the ENERGY BALANCE Mode (as Fig. 35), which displays the balance forecast between the power of home consumption and the power generate by Solar System. In case if the SOLAR produced power is lower than the power consumed, the negative value symbol [ – ] will appear.

Fig. 35

Fig. 36

Press 4 TIMES


From Fig. 35, press the [ Up button3] for about 3 seconds will lead the display screen to enter ENERGY BALANCE History Mode (Fig. 36).

TODAY

MTD

YTD

● the balance of electricity energy from 00:00 of current day to now.

● the balance of electricity energy from 00:00 1st of current month to now.

● the balance of electricity energy from 00:00 1st January of cur-rent year to now.

Press for 3 sec


Balance of energy cost of a specific day

To view the history data of balance energy cost of an exact day, from the COST BALANCE History Mode, press the [ Up button2] for about 3 sec-onds until the display enter into the history date input interface (as Fig. 34).




Fig. 34


Then press the [ Down button3] to display the balance of energy cost for the selected date.

Press for 3 sec

2928


Resetting and Data ClearanceTo clear the history data (resetting), please follow the instruction as follows:

Step 1 • Take out the batteries and unplug the power supply from the Energy Monitor.

Step 2 • Press and HOLD at the same time [ Up button2] and the [ Down button3], then plug in the power supply (or install the batteries) into the Energy Monitor.

The LCD screen will display full LCD display characters as below.


Balance of electricity energy of a specific day

To view the history data of balance electricity energy of an exact day, from the ENERGY BALANCE History Mode, press the [ Up button2] for about 3 seconds until the display enter into the history date input interface (as Fig. 37).




Fig. 37


Then press the [ Down button3] to display the balance of electricity en-ergy for the selected date.

Press for 3 sec

3130

Buzzer Mode of Energy Monitor

Buzzer ModeFrom the HOUSE COST Mode, press the [ Up button2] and [ Down button3] at the same time for about 3 seconds to enter the Buzzer Mode.

If the buzzer is set on, the display unit will makes a “BEE” sound every time the key is pressed.

Then you see the symbol [ bOFF ] on the screen (as Fig. 39), it means the buzz-er was set to be OFF status during production default setting.

Now press shortly the [ Up button2] or the [ Down button3] to switch be-tween ON and OFF status.

When the buzzer is switched to ON status, it makes a “BEE” sound. In (Fig. 40) [ bON ] is the screen symbol of buzzer on status.

After switching to desired status, press the [ Set button1] to finish the set-ting and return to the COST Mode.

HOUSE COST Mode

Fig. 39 Buzzer OFF

Fig. 40 Buzzer ON


Step 3 • After the LED light flashes, release the [ Up button2] and [ Down button3]. The LCD screen will display the programming version (as Fig. 38).

Step 4 • After the LCD screen display the program version, unplug the power supply (or take out the batteries) from the Energy Monitor again.

Step 5 • Then re-install the batteries or plug the power supply again into the Energy Monitor and follow the instruction of 2 Settings before start on P. 6.

Fig. 38

Up to now all of the data has been cleared.

3332

Tips for use

* The information is only for reference, please check with the related parties in your country.

Find out the electric power of your countryAfghanistan, Albania, Angola, Argentina, Armenia, Azerbai-jan, Azores, Balearic Islands, Bangladesh, Belarus, Benin, Bosnia, Burkina Faso, Burundi, Cameroon, Canary Islands, Cape Verde, Central African Republic, Chad, Chile, China, People’s Republic of, Comoros, Congo, Dem. Rep. of (former Zaire), Côte d’Ivoire, Djibouti, East Timor, Egypt, Equatorial Guinea, Ethiopia, Faeroe Islands, French Guiana, Gabon, Georgia, Greece, Greenland, Guinea, Guinea-Bissau, Hong Kong, Israel, Kazakhstan,Korea, South, Lesotho, Lithuania, Luxembourg, Macau, Macedonia, Madagascar, Madeira, Mali, Mauritania, Mongolia, Montenegro, Mozambique, Namibia, New Caledonia, Niger, Pakistan, Paraguay, Peru, Philippines, Réunion Island, Russia, Serbia, Slovenia, Somalia, Syria, Tahiti, Tajikistan, Thailand, Togo, Turkmenistan, Ukraine, United Arab Emirates,Uruguay,Uzbekistan,Yemen, Rep. of, Zimbabwe, Brazil, Costa Rica, Lebanon, Martinique, Monaco, Morocco, Netherlands Antilles, Saudi Arabia, Vietnam, Belize, Cuba, South Africa

220V

Algeria, Andorra, Antigua, Austria, Bahrain, Belgium, Bhutan, Bulgaria, Cambodia, Channel Islands, Congo, People’s Rep. of, Croatia, Czech Republic, Denmark, Eritrea, Estonia, Finland, France, Gaza, Gambia, Germany, Ghana, Grenada (Windward Is.), Guadeloupe, Hungary, Iceland, India, Iran, Iraq, Ireland (Eire), Italy, Jordan, Laos, Liechtenstein, Malawi, Maldives, Mauritius, Montserrat (Leeward Is.), Myanmar (formerly Burma), Nepal, Netherlands, New Zealand, Norway, Poland, Portugal, Romania, Rwanda, St. Kitts and Nevis (Leeward Is.), St. Vincent (Windward Is.), Samoa, Senegal, Sierra Leone, Singapore, Slovak Republic, Spain, Sri Lanka, Sudan, Swaziland, Sweden, Switzerland, Tanzania, Tunisia, Turkey, United Kingdom, Vanuatu, Zambia, Bolivia, South Africa, Indonesia

230V

American Samoa, Bahamas, Bermuda, Canada, Cayman Islands, Guatemala, Latvia, Liberia, Micronesia (Federal States of), Nicaragua, Palmyra Atoll, United States of America, Venezuela, Costa Rica, Ecuador

120V

Anguilla, Colombia, Dominican Republic, Guam, Haiti, Honduras, Jamaica, Panama, Taiwan, Brazil, Belize, Cuba 110V

Aruba, Libya, Mexico, Suriname, Ecuador, Indonesia, Monaco, Morocco, Netherlands Antilles, Saudi Arabia, Vietnam, Ecuador, Indonesia 127V

Japan, Okinawa 100V

Botswana 231V

Barbados, El Salvador, Trinidad & Tobago, Virgin Islands (British and U.S) 115V

Australia, Brunei, Cook Islands, Cyprus, Falkland Islands, Fiji, Gibraltar, Guyana, Isle of Man, Kiribati, Kuwait, Malaysia, Malta, Nauru, Nigeria, Oman, Papua New Guinea, Qatar, St. Lucia (Windward Is.), Seychelles, Tonga, Uganda, Kenya

240V


RJ45-USB Data Cable and SoftwareThe RJ45-USB Data Cable and the software allow you to view your electricity consumption data on your computer.

Please download the software on our website - http://www.wattsclever.com.

Step 1 • Plug the RJ45-USB Data Cable on the back side of the Energy Moni-tor (as Fig. 41).

Step 2 • Plug the RJ45-USB Data Cable - USB side to your PC and use the software that you installed to view your electricity consumption data.

Fig. 41

How electricity is measuredPower is the ability to do work. Electric power is measured in Watts (W), and for large values, in kilowatts (1000 Watts, or kW). A typical incandescent light bulb consumes 60 Watts. A typical microwave oven consumes 1 to 2 kilowatts.

Energy is power used over a period of time. Electric energy is measured in kilowatts-hours(kWh). If you leave a 60W light on for one hour, it consumes 60 Watt-hours, 0.06 kWh. If you leave a 2 kW microwave oven on for 15 minutes, it consumes 0.5 kWh.

Tips for use

3534

For more detailed instructions, FAQ’S, and product support please visit our websites.

www.wattsclever.com www.blog.wattsclever.com www.support.wattsclever.com

Product SpecificationsModel • EW4009

Dimensions:

Energy Monitor • 88 (L) x 74 (W) x 43 (H) mm

LCD Display • 79(L) x 48.5 (H) mm

Power Transmitter • 90.5 (L) x 72 (W) x 44.5 (H) mm

Operating range • 80 - 265V

Wireless transmission • 433 MHz SRD band

Maximum rated sensor current • 100A

Min current sensitivity • 0.1A

Transmission Distance • 30m

Room 1407, 14/F,

New Victory House,

93-103 Wing Lok Street,

Sheung Wan, Hong Kong

W www.wattsclever.com

T +852 2815 6700

Watts Clever(International) Limited

© 2011 Watts Clever (International) Limited

All Rights Reserved

Made in China

Now, WIRELESS Solar Energy Monitor is ready to work.Feedback on your electricity consumption will help you change your energy habits, resulting in lower electricity bills. Many household have saved up to 20% of their electricity bills by using the WIRELESS Solar Energy Monitor.

Typical power consumption for some household appliances:

Television

Air conditioner

Hot water heater

150 W

2000 - 5000 W

4000 W

Toaster

Microwave

1000 W

1000 - 2000 W

My Appliances Cost:

Dishwasher

Clothes washer

Coffee maker

Electric hot water heater for bath or shower

$ ___________ / Hour

$ ___________ / Hour

$ ___________ / Hour

$ ___________ / Hour

Power generated by Solar System:

Day time

Night time

Other Electrical Appliances:

__________kw / Hour

__________kw / Hour

$ ___________ / Hour

$ ___________ / Hour

___________________________________________

___________________________________________

WIRELESS Solar Energy Monitor - Jaycar Watts Clever WIRELESS Solar Energy Monitor helps you conserve...

Documents

Transcript of WIRELESS Solar Energy Monitor - Jaycar Watts Clever WIRELESS Solar Energy Monitor helps you conserve...