929001470180

Wireless

Wireless LCD Control Panel

Datasheet

WirelessWireless LCD Control Panel

2019/01

This product is a liquid crystal touch multifunctional control panel with built-in wireless communication chip, which

can control other equipment wirelessly, such as lighting, air conditioning, etc. Including control page of lighting,

curtain, scene, temperature, etc., supporting lighting brightness, opening and closing control, air-conditioning,

heating, mode switch, curtain opening and closing action; A variety of scene calls, such as home, away from home,

greeting visitors, cinema mode, to achieve a key direct corresponding scene, such as lighting open, curtain open, air

conditioning open.

Features

• One-click scene control

• For lighting dimming

• For floor heating control

• For air conditioning control

• For curtain opening and closing or

support equipment control with ON

and OFF functions

• ZIGBEE's scene control

• Replace the traditional mechanical 86

control buttons

Bene�ts

• 86 panel, install on the wall easily

• Capacitive multifunctional touch LCD display

• Wireless access, meet 802.15.4 physical

standards

• Meet ZIGBEE ZHA compliance agreement

• Control zigbee-related equipment directly, such

as lighting, curtains, etc

• Abundant control pages with protocols such as

scenario control and group control.

• Support for custom names

• Support up to 12 scenario

• Support up to 20 lamp control

Application

• Office

• Classroom

• Hotel

• Home

2 - 5 2019/01

Electrical data

Speci�cation item Value Unit Conditions

Supply Voltage 5 Vdc

Input Current 190 mA

LCD Size 3.5 Inch

LCD TFT Resolution 320 × 3（RGB）× 240

LCD Type TFT

Touch key type Capacitive touch

ESD 4KV @ conductive

8KV @ air

RF data

Speci�cation item Value Unit Conditions

RF Frequency 2.4 … 2.485 GHz

Channel 16 pcs

Modulation QPSK （DSSS）

Transmit Power 8…10 dBm Conditions: 2.0-3.6V, +25ºC

Typical value ：8.5

Receiving Sensitivity -92 … -96 dBm Nominal for 1% PER

Typical value ：-94

Maximum receiver input power +10 dBm For 1% PER measured as sensitivity;

supply current at 14.7 mA

Physical Protocol 802.15.4

Security 128 bit AES

EMC & SAFETY

Speci�cation item Value

SAFETY GB19510.1, GB19510.14

EMC GB17625.1, GB/T 17626.4, GB/T 17626.5, GB/T 17626.7, GB9254-2008(CISPR22-2006)

ESD GB/T17626.2（IEC61000-4-2）

Datasheet - Wireless LCD Control Panel

Operational temperatures and humidity

Speci�cation item Value Unit Conditions

Ambient temperature -20...+50 ºC

Relative humidity 10...90 %

Product Data

All speci�cations are typical and at 25 °C Tcase unless otherwise speci�ed.

Ordering Information

Commercial product name 12NC Carton Quantity

Wireless LCD Control Panel 929001470180 30 pcs

Dimensions and weight

Speci�cation item Value Unit Conditions

Material ABS + PC (V0 AC3100）

Color RAL9016

Dimensions L x W x H 88.6 X 88.6 X 12.2 mm Tolerance：+/- 0.1mm

Weight 96 gram

3 - 5 2019/01

Certi�cates and standards

Speci�cation item Value Unit Conditions

Approval marks CE

RoHS RoHS

REACH REACH

ZIGBEE ZIGBEE

Audible noise < 20 dB

Ingress Protection classi�cation IP20

Datasheet - Wireless LCD Control Panel

Data Sheet

Item Dimensions (mm)

A1 88.6

B1 88.6

C1 8.2

C2 13.2

D1 40

E1 32

F1 21

Dimensions (mm)

Wireless LCD Control Panel

Storage temperature and humidity

Speci�cation item Value Unit Conditions

Ambient temperature -25...+85 ºC

Relative humidity 5...95 %

Lifetime

Speci�cation item Value Unit Conditions

Lifetime 30000 Hours Maximum failures=10%

E1

F1

D1

4 - 5 2019/01

Wiring & Connections

1. Fix the base of product to the 86 base of wall with screws

2. Put the power supply of accessories into 86 boxes and connect the 220V mains wire with the wire L and N

of the accessories;(where input: brown L, blue N;Output: 2 pin jack, red L, black N;Note: please disconnect

the 220V power supply when wiring

3. Connect the output of the accessory power supply and the power input of the multi-function touch panel

as shown below

4. Lock the wall bracket as shown below on the transit box through the �tting screw (note that the arrow is up

in the correct direction)

5. Insert the product power wire and output wire of the power supply through the terminal and tilt the

product at a certain Angle. Fasten the upper button and then press the lower end of the product

Datasheet - Wireless LCD Control Panel

01/2019 Data subject to change

www.lighting.philips.co.uk/oem-emea/products/connected-lighting

© 2019 Signify Holding, IBRS 10461, 5600VB, NL. All rights reserved.

The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial o�er and does not form part of any quotation or contract, unless otherwise agreed by Signify.Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.