WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for...

24
WHITE PAPER - 2012 Connectivity Solutions for Home Networking

Transcript of WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for...

Page 1: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

WHITE PAPER - 2012Connectivity Solutions for Home Networking

Page 2: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

2

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

SCOTT EDWARDS Business Development Manager Clipsal

ROBERT CARRICK Business Development ManagerHills Solution Group

IAN MILLNERTechnical ConsultantCopper Development Centre

TREVOR OATESChief Boffi nBaby Boomers’ Boffi n

25 years in telecommunications and data communications. Recently data communications consultant at Clipsal Australia. Then in to business development to implement the technical challenges of broadband and television distribution and to commercialise products and solutions for installation technicians. Industry participation in varied positions as technician, project manager, technical specialist, for networking and passive connectivity for enterprise and outside plant systems.

A career that spans Telecommunications, Broadcast Television and Information technology. He’s worked for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings. Robert is a regular contributor to the Smart Wired® industry initiative. Robert has been an advocate of minimising the impact that convergence is having in the residential space through good planning and preparation. Robert believes that even a small amount of planning by a resident can deliver a large benefi t in terms of access to services as well as minimising disruption as new convergent technology and infrastructure, such as Digital Television and the National Broadband Network roll out.

Ian Millner’s career in telecommunications spans over thirty years. He started his career with Telecom Australia working in transmission and broadcasting. He founded a training company that has trained over 30,000 electricians and telecommunications technicians and was instrumental in the development of the Smart Wired® cabling platform and the Code of Practice for Home Wiring. Ian sits on various Communications Alliance Committees and also the Cabling Advisory Group.

Trevor has over 30 years’ experience in the telecommunications industry, working for both telecommunications service providers and telecommunications equipment manufacturers, in roles across network design and implementation, software design, creation and testing, customer support and fault fi nding. He recently created and ran a world class Executive Briefi ng Centre, presenting technical concepts to both technical and non-technical audiences. He now runs his own technology advice and assistance service company.

ABOUT THE AUTHORS

Page 3: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

3

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

INTRODUCTION

Developments in Home Networking ....................4

Connectivity solutions .........................................6

New or renovated homes ...................................6

Existing homes ...................................................6

About the solutions .............................................6

SOLUTION 1

Wired - Fibre .......................................................8

Standards ...........................................................8

Advantages ........................................................8

Disadvantages ....................................................8

SOLUTION 2

Wired - Cat 5 or 6 ...............................................9

Standards ...........................................................9

Advantages ........................................................9

Disadvantages ....................................................9

SOLUTION 3

Power Line Communications (PLC) (Ethernet Over Power Line) ...............................10

Standards .........................................................10

Advantages ......................................................10

Disadvantages ..................................................10

SOLUTION 4

Ethernet over phone line (Telephony Twisted Pair) .....................................12

Standards .........................................................12

Advantages ......................................................12

Disadvantages ..................................................12

SOLUTION 5

Ethernet over coax (Coaxial cabling) .................13

Standards .........................................................13

Advantages ......................................................13

Disadvantages ..................................................13

SOLUTION 6

Wireless (Wi-Fi) .................................................14

Standards .........................................................14

Advantages ......................................................14

Disadvantages ..................................................14

MULTIPLE CONNECTED DEVICES

Wired – Fibre ....................................................15

Wired - Cat 5 or 6 .............................................16

Power Line Communications (PLC) (Ethernet Over Power Line) ...............................17

Ethernet Over Phone Line (Telephony Twisted Pair) ....................................18

Coax cabling ....................................................19

Wireless (Wi-Fi) .................................................20

In summary ......................................................20

Conclusion .......................................................21

References .......................................................22

CONTENTS

Page 4: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

4

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

As new telecommunications services were developed and introduced over time, it was simpler for Service Providers to deliver them across individual networks. In recent years and, largely due to fi nancial pressures, Service Providers have converged their service backbones and delivery mechanisms to Internet Protocol (IP) platforms, gaining economies of scale and removing unnecessary duplication of links in their networks.

Figure 1 illustrates how services are typically delivered to homes today. Whilst there is some sharing of network infrastructure between voice and data getting to the home, in the home they are separate. Free to air and pay TV come in on different networks and terminate on the same TV device. Other services such as security, audio and so on could be added to this diagram, each having its own domestic connections.

The transformation of Service Provider networks to IP is now infl uencing the delivery of advanced

services in the home and in February 2011 the Australian Communications and Media Authority (ACMA) published a paper titled ‘Development in Home Networks’ which looked at the changing architecture of the traditional separate networks into the converged IP based Network. The paper stated that: “emerging IP-based services such as health monitoring, security, home automation, entertainment and social networking accessible via home networks are reshaping the user experience.”

We are now seeing this major shift, from separate networks, to a common IP transport platform delivering a multitude of services. This transformation is being fast tracked by the rollout of fi bre to the home in the form of the National Broadband Network (NBN), an initiative of the Department of Broadband, Communications and the Digital Economy. As the NBN is implemented, all service providers will deliver their services across the NBN using IP.

DEVELOPMENTS IN HOME NETWORKING

FIGURE 1 INDIVIDUAL NETWORKS TO SUPPORT SERVICE DELIVERY

$

Voice and internet provider

Phone Socket

STB

Pay TV head end

Free to airTV

ADSLmodem

Page 5: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

5

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

FIGURE 2 CONVERGED NETWORK

Figure 2 shows how the separate specialised networks are replaced by one that is horizontally integrated with all services using the same IP delivery mechanism. Unfortunately, while all services are delivered to the home via IP, the connectivity in the home between the service providers’ network and the home devices may be achieved by using any one or mix of the following technologies:

1. Wired – Fibre2. Wired – Cat 5 or 63. Power Line Communications (PLC)

(Ethernet Over Power Line)4. Ethernet Over Phone Line (Telephony

Twisted Pair)5. Ethernet Over Coax (Coaxial Cabling)6. Wireless (Wi-Fi)

The ACMA’s paper concludes that: “consumers will need to be more aware of technical aspects. Both industry and consumers will have a role in meeting this awareness through education to improve technical expertise and awareness of technological developments”.

How can we best support the consumer, so as to simplify the internal network in the home?

One starting point for this is the deployment of a homogenised connectivity, open platform using a structured cabling solution based on category 5 or 6 cabling, augmented by wireless for mobility. This makes the future management of the network simpler, allowing the partnership between the consumer and the contractor to grow. Whilst this is the utopian position achievable in new homes, this at face value is not as cost effective for existing homes.

It is therefore important to provide the consumer with a comparison of the range of connectivity technologies that are available so that they can make an informed decision.

@

Pay TV

$Voice and

internet providerVoice and

internet providerPay TV

head endFree to air

TV

IPTV

Delivery mechanism to the dwellingIP over fibre, radio and satellite

Delivery mechanism to the device:IP over fibre, wireless, PLC, coax, twisted pair & Cat 5/6

Page 6: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

6

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

ABOUT THE SOLUTIONS

The purpose of this section is to expose you to the range of connectivity technologies available for use in a residential home. So you can, in turn, advise the consumer. All technologies presented are viable solutions but it is important to make an informed decision as to which is the best connectivity solution for a particular application.

When looking at the best connectivity solutions for the home for the incoming and interactive services provided by the NBN, it is simpler to divide the home market into two main categories:

1. New or renovated homes2. Existing homes

NEW OR RENOVATED HOMES

The connectivity solution for a new home, or one that is being renovated, is best achieved through a hybrid of:

3. Wired (for fi xed location devices such as TV, alarm system, Smart Home controls)

4. Wireless (for devices mobile in the home such as laptops, phone handsets, tablet computers)

Note: While the connectivity solutions listed below can be used in a new home once it has been built, a wired solution included in the build is considered the optimum solution given the cost of installation is low if it is installed when the home is being built.

EXISTING HOMES

The connectivity solution for an existing home is a mixture of a much greater range of technologies, these being:

1. Wired – Fibre2. Wired – Cat 5 or 63. Power Line Communications (PLC)

(Ethernet Over Power Line)4. Ethernet Over Phone Line (Telephony

Twisted Pair)5. Ethernet Over Coax (Coaxial Cabling)6. Wireless (Wi-Fi)

What the consumer needs to know is exactly what each solution is and what are the benefi ts and disadvantages of each solution.

In this section we look at what you would need to establish a simple connection from the NBN’s Network Termination Device (NBN Box) using each of the above listed technologies. At one end we have NBN’s network termination device (NTD, sometimes referred to as Optical Network Terminal or ONT) and at the other end a computer as seen in Figure 3. (This is representative of any device with an IP connection).

For each technology, we show in red the connectivity solution in place from the NTD to the Computer.

CONNECTIVITY SOLUTIONS

Computer

To Electrical switchboard

PSU NTD

To Electrical switchboard

FIGURE 3 NBN’S NTD AND COMPUTER WITH NO CONNECTIVITY

Page 7: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

7

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

Page 8: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

8

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

Computer

Connection topower

Optical Fibre

fly lead

To Electrical switchboard

Media converter

fly lead

Connection topower

PSU NTD

To Electrical switchboard

Media converter

WIRED - FIBRE

SOLUTION

1Figure 4 shows the connectivity provided by fi bre. The full link consists of 5 elements. It shows optical fi bre running from the location of the NTD to where the computer is located, and the fi bre terminated on fi bre connectors. At each end of the fi bre is a media converter and then a cat 5 or cat 6 fl y lead from the media converter to the NTD or the computer. The media converter converts the electrical data signal RJ45 interface on the NTD to an optical signal for transmission over the fi bre and back again. The IP data interface at the computer is typically an RJ45 connector.

STANDARDS

The installation of this type of connectivity is covered by cabling standards and must be performed by a registered cabler. (See References Section for Standards)

ADVANTAGES

1. Dedicated link between the NTD and the computer and there is no bandwidth limitation due to the media type as fi bre will support well beyond 1Gbps.

The bandwidth is limited because of the media converter or computer Network Interface Card (NIC) but these are typically specifi ed at 1Gbps.

2. Highest security as the only way to intercept this link is physically.

3. Life cycle of fi bre is typically as long as the building’s life cycle.

4. Easy to use, no specifi c confi guration requirements, no password or encryption required.

DISADVANTAGES

1. Not good for mobile devices.2. Higher cost to install in existing home.3. If the cabling is installed in concealed

locations, it must be installed by a registered cabler.

4. Each additional device or location you want to add to the network requires a new cable to be installed.

5. The media converters need to be permanently powered and will require replacement on failure.

FIGURE 4: CONNECTIVITY PROVIDED BY FIBRE

Page 9: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

9

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

WIRED- CAT 5 OR 6

SOLUTION

2Figure 5 shows the connectivity technology used. A fi xed cat 5 or cat 6 cable with RJ45 sockets at both ends and a fl y lead at both ends to connect to the NTD and the computer. This link is composed of 3 elements, so the connectivity solution in this case consists of passive wire, sockets and plugs.

STANDARDS

The installation of this type of connectivity is covered by cabling standards and must be performed by a registered cabler. (See References Section for Standards)

ADVANTAGES

1. Connectivity is passive and therefore very reliable.

2. Dedicated link between the NTD and the computer so there is no bandwidth limitation. Typically 1Gbps, the only limitation is the speed of the interface card in the computer and the ONT.

3. Highest security as the only way to intercept this link is physically.

4. When not in use consumes no power.5. Life cycle of cable is typically as long as the

building’s life cycle.6. Easy to use, no specifi c confi guration

requirements, no password or encryption required.

7. Easy to fault fi nd as there are no active components in the link. So a problem is either in the NTD, the cable or the computer.

DISADVANTAGES

1. Not good for mobile services.2. High installation cost in existing home.3. If the cabling is installed in concealed

locations it must be installed by a registered cabler.

4. Each additional device or location you want to add to the network requires a new cable to be installed

FIGURE 5: WIRED CONNECTIVITY PLATFORM

Computer

PSU NTD

Cat 5 or Cat 6 cable

To Electrical switchboard

To Electrical switchboard

Page 10: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

10

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

POWER LINE COMMUNICATIONS (PLC) (ETHERNET OVER POWER LINE)

SOLUTION

3Figure 6 shows the 5 elements that go to make up the Ethernet over Power Line connectivity platform. In this case you need to have an adaptor at both ends that plugs into the existing power point, then a Cat 5/6 fl y lead from the adaptor to the NTD and from the adaptor to the computer. The fi fth element is the physical electrical cabling installation in the home.

STANDARDS

There is a range of vendors’ implementation of standards that compete with each other and care should be taken when choosing additional equipment. Over time there will be harmonisation but until this happens care should be taken on which standards to deploy.

DEVELOPING STANDARDS

This section lists the more current development of standards.

G.hn which is a new standard ratifi ed recently by ITU and supported by the Home Grid Alliance.

IEEE 1901 which is a formalised adoption of the original Home Plug standards

EXISTING STANDARDS

These are standards developed by alliances of companies promoting standardisation to allow for the creation of a new market.

HomePlug 1.0

HomePlug AV

HomePlug Green PHY

ADVANTAGES

1. Connectivity link utilises the existing electrical cabling installation.

2. Installation can be performed by the home owner.

3. Can provide temporary connectivity in rented homes.

4. No licensing requirements for installers.

DISADVANTAGES

1. The performance of the link is dependent on the electrical installation. As the electrical installation was not designed as a communications link, the actual transmission speeds (throughput) may vary from time to time and be signifi cantly lower than the predicted maximum of the adaptors installed.

2. If the power points used are on different power phases there may be limited or no connectivity.

3. As you add more adaptors the electrical cabling becomes a shared medium, resulting in lower throughput.

4. Whilst the adaptors use encryption for security, they are on a shared cabling infrastructure that extends beyond the home.

5. There are competing standards and chipsets so care should be taken when buying additional adaptors.

6. Whilst the theoretical number of adaptors that can be connected is large, this does not seem to translate well into a real life practical installations.

7. The adaptor takes up a power point, though some models have a “Pass-thru” power outlet to overcome this.

8. The adaptors need to be permanently powered and will require replacement on failure.

9. Fault fi nding can be more complex as there are more elements between the computer and the NTD.

10. Not best for mobile services, but the adaptors can be moved between power points as the computer is relocated.

Page 11: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

11

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

FIGURE 6 ETHERNET OVER POWER LINE CONNECTIVITY PLATFORM

Adaptor

PSU NTD

Adaptor Computer

To Electrical switchboard To Electrical

switchboard

Page 12: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

12

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

ETHERNET OVER PHONE LINE(TELEPHONY TWISTED PAIR)

SOLUTION

4Figure 7 shows the 5 elements that go to make up the Ethernet over Phone Line connectivity platform. In this case you need to have an adaptor at both ends that plugs into the existing phone outlets, then a cat 5/6 fl y lead from the adaptor to the NTD and from the adaptor to the computer.

STANDARDSThere is a range of competing standards so care should be taken when choosing additional equipment. Over time there will be harmonisation but until this happens care should be taken on which standards to deploy.

DEVELOPING STANDARDSThis section lists the more current development of standards.

G.hn which is a new standard ratifi ed recently by ITU and supported by the Home Grid Alliance.

EXISTING STANDARDS These are standards developed by alliances

of companies promoting standardisation to allow for the creation of a new market.

HomePNA also an ITU standard G9954

ADVANTAGES1. Connectivity link utilises the existing

telephone cabling installation.

2. nstallation can be done by the home owner (assuming telephone cabling exists).

3. Can provide temporary connectivity in rented homes.

4. No licensing requirements to be installed.

DISADVANTAGES1. The performance of the link is dependent

on the quality of the telephone cabling installation. Some home telephone cabling installations could be decades old.

2. As you add more devices the phone cabling becomes a shared medium.

3. Each adaptor requires access to a power point as they are active devices.

4. The adaptors need to be permanently powered and will require replacement on failure.

5. Fault fi nding can be more complex as there are more elements between the computer and the NTD.

6. Not best for mobile services, but the adaptors can be moved between phone socket locations as the computer is relocated.

FIGURE 7 ETHERNET OVER PHONE LINE

Connection topower

PSU NTD

Adaptor

Adaptor

Computer

To Electrical switchboard

Connection topower

Existing telephone cable

Page 13: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

13

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

POWER LINE COMMUNICATIONS (PLC) (ETHERNET OVER POWER LINE)

SOLUTION

5Figure 8 shows the 5 elements that go to make up the Ethernet over Coax connectivity platform. In this case you need to have an adaptor at both ends that plugs into the existing coax outlets, then a cat 5/6 fl y lead from the adaptor to the NTD and from the adaptor to the computer.

STANDARDSThere is a range of standards that compete with each other and therefore care should be taken when choosing additional equipment. Over time there will be harmonisation but until this happens care should be taken on which standards to deploy.

DEVELOPING STANDARDSThis section lists the more current development of standards.

G.hn which is a new standard ratifi ed recently by ITU and supported by the Home Grid Alliance.

EXISTING STANDARDSThese are standards developed by alliances of companies promoting the creation of a new market.

HomePNA also an ITU standard G9954 Cwave

ADVANTAGES1. Connectivity link utilises the existing coax

cabling installation.2. Installation can be done by the home owner.3. Can provide temporary connectivity in

rented homes.4. No licensing requirements to be installed.

DISADVANTAGES1. The performance of the link is dependent

on the quality of the cabling installation. Some television cabling installation could be decades old.

2. As you add more devices the coax cabling becomes a shared medium.

3. Each adaptor requires access to a power point as they are active devices.

4. The adaptors need to be permanently powered and will require replacement on failure.

5. Fault fi nding can be complex as there are more elements between the computer and the NTD.

6. Not good for mobile services.7. 7Care must be taken that any adaptors do

not interfere with any existing RF services which may already be using the coax cable.

8. 8Very complex to deploy in high rise apartments or any home which uses a shared television distribution system such as a mast-head distribution amplifi er or cable splitter.

FIGURE 8 ETHERNET OVER COAX CABLE

Connection topower

To Electrical switchboard

PSU NTD

Adaptor

Adaptor

Computer

To Electrical switchboard

Connection topower

Existing television coax cable

Page 14: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

14

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

WIRELESS (WI-FI)

SOLUTION

6Figure 9 shows a typical wireless connection which consists of 3 elements. The 3 elements are the fl y lead from the NTD to the wireless router, the wireless router and the link provided by the atmosphere. The wireless router is connected to the NTD and uses the computer’s wireless capability or interface card.

STANDARDS

Wireless standards have now been around for some time and the one dominant standard is IEEE 802.11 commonly referred to as Wi-Fi. There are specifi c vendor enhancements to this standard which claim to deliver higher throughput, but only between pairs of wireless components that support the specifi c enhancement.

ADVANTAGES

1. Easy to install.2. Ideal for all mobile devices.3. Very common support on portable devices.

DISADVANTAGES

1. Performance suffers as the distance from the wireless router increases.

2. Walls and fl oors can reduce performance or prevent wireless communications.

3. Performance may be variable due to interference from other wireless devices such as microwave ovens, blue tooth devices etc.

4. Wireless in adjacent high rise apartments can cause interference leading to variable and poor performance.

5. Wireless is a shared medium so as the number of devices increases, individual throughput decreases.

6. Requires security confi guration (Modern wireless routers support push button security enrolment).

7. The wireless router is active and powered with a power pack. Either device may be a point of failure and require replacement.

FIGURE 9: WIRELESS

PSU NTD

To Electrical switchboard

WIRELESS ROUTER

Connection topower

Computer

To Electrical switchboard

Page 15: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

15

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

MULTIPLE CONNECTED DEVICES

So far we have considered only one device connected to the NTD. The question then arises, what happens when there is more than one device? To answer this question we can look at each connectivity option when more than one device is required.

The connectivity options are: 1. Wired – Fibre2. Wired – Cat 5 or 63. Power Line Communications (PLC)

(Ethernet Over Power Line)4. Ethernet Over Phone Line (Telephony

Twisted Pair)5. Ethernet Over Coax (Coaxial Cabling)6. Wireless (Wi-Fi)

NOTE

Whilst the NTD provided as part of the NBN roll out has up to four ports,

each port is likely to be assigned to a different service provider. For

example your ISP may be on port 1, your security may be on port 2 etc.

1. WIRED – FIBREFigure 10 shows multiple computers connected via individual fi bre links so every link has the full transmission capacity of the fi bre technology, which is easily 1Gbps. This involves two more media converters and their power supplies for each additional connected device.

FIGURE 10 MULTIPLE USERS, USING FIBRE LINKS

Data switch

Connection topower

Connection topower

PSU NTD

To Electrical switchboard

Computer

To Electrical switchboard

Computer

Computer

Computer

fly lead

fly lead

fly lead

fly lead

Media converter

Media converter

Media converter

Media converter

Media converter

Media converter

Media converter

Media converter

Media converter

Optical Fibre

Optical Fibre

Optical Fibre

Optical Fibre

fly leads

fly leads

Note: The data switch must be a layer 3 switch or have router functionality with in built DHCP function

Page 16: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

16

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

Note: The data switch must be a layer 3 switch or have router functionality with in built DHCP function

PSU NTD

To Electrical switchboard

Computer

Cat 5 or Cat 6 cable

To Electrical switchboard

Computer

Data switch

Computer

Computer

2. WIRED - CAT 5 OR 6

Figure 11 shows multiple computers connected via individual Cat 5/6 links so every link has the full transmission capacity of the Cat 5/6 technology which is up to 1Gbps.

FIGURE 11 MULTIPLE USERS USING UTP LINKS

Page 17: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

17

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

3. POWER LINE COMMUNICATIONS Figure 12 shows multiple computers connected via PLC links. In this case every device connected via the PLC link is sharing the one resource, which is the electrical wiring. The maximum transmission speed to each device will vary depending on the number of devices sharing the wiring. The number of adaptors will vary with the number of computers as this technology supports “one to many” connections from the one adaptor at the NTD to the many at the computers.

FIGURE 12 MULTIPLE USERS USING PLC

Adaptor

PSU NTD

Adaptor

To Electrical switchboard

To Electrical switchboard

Computer

Adaptor

Computer

Adaptor

Computer

Page 18: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

18

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

4. ETHERNET OVER PHONE LINE Figure 13 shows multiple computers connected via Ethernet over phone cabling. In this case every device connected via the phone cabling is sharing the one resource, which is the telephone cabling. The maximum transmission speed to each device will vary depending on the number of devices sharing the resource. An additional adaptor and associated power supply will be needed for each additional computer.

FIGURE 13 MULTIPLE USERS USING ETHERNET OVER TELEPHONE CABLING

Connection topower

To Electrical switchboard

PSU NTD

Adaptor

Adaptor

To Electrical switchboard

Existing telephone cable

ComputerComputer

Computer

Page 19: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

19

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

5. COAX CABLINGFigure 14 shows multiple computers connected via Ethernet over Coax. In this case every device connected via Ethernet over Coax link is sharing the one resource, which is the coax cabling. The maximum transmission speed to each device will vary depending on the number of users sharing the resource. An additional adaptor and associated power supply may be needed for each additional computer, especially if the computers are distributed through the home.

FIGURE 14 MULTIPLE USERS USING ETHERNET OVER COAX

Computer

Computer

Computer

To Electrical switchboard

To Electrical switchboard

Adap

tor

Adap

tor

Adap

tor

Adaptor

Existing television coax cable

NTDRJ45 fly lead

RJ45 fly lead

RJ45 fly leadTV Antenna

cable

TV Antennacable

Page 20: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

20

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

6. WIRELESS (WI-FI)Figure 15 shows multiple computers connected via the wireless link. Every device connected via the wireless link is sharing the one resource, which is the RF spectrum. The maximum transmission speed to each device will vary depending on the number of users.

FIGURE 15 MULTIPLE USERS USING WIRELESS LINK

PSU NTD

To Electrical switchboard

WIRELESS ROUTER

Connection topower

Computer

Computer

Computer

Computer

To Electrical switchboard

IN SUMMARYWhen the number of users increases, the link speed to each user on fi bre and UTP cabling system will not change.

When the number of users increases, the link speed will be adversely affected by the number of users, when using PLC, Ethernet over Coax, Ethernet over Phone Line or Wireless.

Page 21: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

Wired fi bre Wired Cat 5/6 PLC Ethernet over Phone lines

Ethernet over coax Wireless

Connectivity Elements 1 3 1 1 1 3

Standards 3 3 1 1 1 3

Mobility 1 1 2 1 1 3

Security 3 3 1 1 1 1

Reliability 3 3 2 2 2 2

Sustainability 2 3 2 2 2 2

Installation cost 1 1 3 3 3 1

Fault fi nding 3 3 1 1 1 2

Regulated 3 3 1 1 1 2

TABLE 1 COMPARATIVE ANALYSIS OF CONNECTIVITY TECHNOLOGIES

Wired fi bre Wired Cat 5/6 PLC Ethernet over Phone lines

Ethernet over coax Wireless

Affect on link speed due to multiple users

TABLE 2 COMPARATIVE ANALYSIS OF LINK SPEED AGAINST MULTIPLE USERS

As speed is the most critical peformence meassure it has been given a score out of 15 whilst all other critiria have a score out of 3

The overall comparative score for the technologies are shown in

Wired fi bre Wired Cat 5/6 PLC Ethernet over Phone lines

Ethernet over coax Wireless

Overall rating /42 35 38 19 18 18 24

TABLE 3 OVERALL RATING

CONCLUSIONAll of the technologies detailed in this document are viable and have their place in the market as they allow for connectivity to be created in the home, making the deployment of services possible. Many of the technologies have been developed to be plug and play technology, so the home user can easily install and operate them. Whilst this is the intention, in the long term as the number of devices grows, fault fi nding becomes an ever growing challenge.

As a professional it is advisable that due consideration be given to the use of each of these technologies so ensuring the connectivity platform is:

Safe

Secure

Reliable / Robust

Sustainable

IN THE FOLLOWING TABLES A RATING HAS BEEN GIVEN TO THE TECHNOLOGY ALONG THE TO AGAINST THE CRITERIA LISTED ON THE LEFT HAND COLUMN. THIS RATING IS:

1. Poor 2. Fair 3. Good

15 15 5 5 5 5

Page 22: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

22

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

REFERENCES

http://www.acma.gov.au/WEB/STANDARD/pc=PC_312456

CABLE INSTALLATION STANDARDS

1. AS/NZS 3080 Telecommunications installations - Generic cabling for commercial premises.

2. AS/ACIF S009 Installation requirements for Customer Cabling (Wiring Rules) (Deals primary with safety)

3. AS/NZS ISO /IC 15018 Information technology – Generic cabling for homes

There is also a range of international standard that have contributed to the development of the Australian and New Zealand Standard, these are:

1. EIA/TIA 568A - This is the American standard and was the fi rst to be published (1991).

2. ISO/IEC 11801 - The International standard for structured cabling systems.

3. CENELEC EN 50173 - The European cabling standard.

Wired fibre Wired Cat 5/6 PLC Ethernet over Ethernet over WirelessPhone LInes coax

RATI

NG

TECHNOLOGIES

45

40

35

30

25

20

15

10

5

0

OVER ALL TECHNOLOGY RATING

You can now look at the various technologies and make a more informed decision based on the advantages, disadvantages and your specifi c need.

FIGURE 16 COMPARATIVE ANALYSIS OF HOME CONNECTIVITY TECHNOLOGIES

Page 23: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

23

CONNECTIVITY SOLUTIONS FOR HOME NETWORKING

NOTES

Page 24: WHITE PAPER - 2012registeredcablers.com.au/assets/template/SW Booklets/6912_07 SW... · for Telstra, TCN-9, The Sydney Opera House, Sony Broadcast, IBM, Avnet and Hills Holdings.

For further information email us at [email protected] or call us direct on 1800 075 060.

International Copper Association AustraliaSuite 1, Level 7, Westfi eld Towers

100 William Street, Sydney NSW 2011Tel: (+612) 9380 2000 Fax: (+612) 9380 2666

www.smartwiredhouse.com.au