Which of the following statements are true regarding RIP v1 and v2? (Choose three.)
22
Cisco 3 - Classless Page 1 06/15/22 Module 1 The subnet 192.168.32.16/28 has been selected to be further subnetted to support point-to-point serial links. What is the maximum number of serial links that this plan can support? 1. 2 2. 3 3. 3 if ip subnet-zero is enabled 4. 4 5. 6 6. 8
-
Upload
samantha-branch -
Category
Documents
-
view
37 -
download
2
description
The subnet 192.168.32.16/28 has been selected to be further subnetted to support point-to-point serial links. What is the maximum number of serial links that this plan can support? 2 3 3 if ip subnet-zero is enabled 4 6 8. - PowerPoint PPT Presentation
Transcript of Which of the following statements are true regarding RIP v1 and v2? (Choose three.)
Cisco 3 - Classless
Page 104/20/23
Module 1
The subnet 192.168.32.16/28 has been selected to be further subnetted to support point-to-point serial links. What is the maximum number of serial links that this plan can support?
1. 2
2. 3
3. 3 if ip subnet-zero is enabled
4. 4
5. 6
6. 8
Cisco 3 - Classless
Page 204/20/23
Module 1
The subnet 192.168.32.16/28 has been selected to be further subnetted to support point-to-point serial links. What is the maximum number of serial links that this plan can support?
1. 2
2. 3
3. 3 if ip subnet-zero is enabled
4. 4
5. 6
6. 8
Cisco 3 - Classless
Page 304/20/23
Module 1
Which of the following statements are true regarding RIP v1 and v2? (Choose three.)
1. Both RIP versions use hop count.
2. Both RIP versions can provide authentication of update sources.
3. Both RIP versions use 16 hops as a metric for infinite distance.
4. RIP v1 uses split horizon to prevent routing loops while RIP v2 does not.
5. RIP v1 uses hold-down times to prevent routing loops while RIP v2 does not.
6. RIP v1 broadcasts routing table updates, while RIP v2 multicasts its updates
Cisco 3 - Classless
Page 404/20/23
Module 1
Which of the following statements are true regarding RIP v1 and v2? (Choose three.)
1. Both RIP versions use hop count.
2. Both RIP versions can provide authentication of update sources.
3. Both RIP versions use 15 hops as a metric for infinite distance.
4. RIP v1 uses split horizon to prevent routing loops while RIP v2 does not.
5. RIP v1 uses hold-down times to prevent routing loops while RIP v2 does not.
6. RIP v1 broadcasts routing table updates, while RIP v2 multicasts its updates
Cisco 3 - Classless
Page 504/20/23
Module 1
A new network is to be configured on a router. Which of the following tasks must be completed to configure this interface and implement dynamic IP routing for the new network? (Choose three.)
1. Select the routing protocol to be configured.
2. Assign an IP address and subnet mask to the interface.
3. Update the ip host configuration information with the device name and new interface IP address.
4. Configure the routing protocol with the new network IP address.
5. Configure the routing protocol with the new interface IP address and subnet mask.
6. Configure the routing protocol in use on all other enterprise routers with the new network information.
Cisco 3 - Classless
Page 604/20/23
Module 1
A new network is to be configured on a router. Which of the following tasks must be completed to configure this interface and implement dynamic IP routing for the new network? (Choose three.)
1. Select the routing protocol to be configured.
2. Assign an IP address and subnet mask to the interface.
3. Update the ip host configuration information with the device name and new interface IP address.
4. Configure the routing protocol with the new network IP address.
5. Configure the routing protocol with the new interface IP address and subnet mask.
6. Configure the routing protocol in use on all other enterprise routers with the new network information.
Cisco 3 - Classless
Page 704/20/23
Module 1
Router1 and Router2 shown in the topology have been configured with the no ip subnet-zero command. Which of the following valid VLSM network numbers could be used for the serial link between Router1 and Router2? (Choose two.)
1. 192.168.1.0/30
2. 192.168.1.4/30
3. 192.168.1.8/30
4. 192.168.1.96/30
5. 192.168.1.138/30
6. 192.168.1.190/30
Cisco 3 - Classless
Page 804/20/23
Module 1
Router1 and Router2 shown in the topology have been configured with the no ip subnet-zero command. Which of the following valid VLSM network numbers could be used for the serial link between Router1 and Router2? (Choose two.)
1. 192.168.1.0/30
2. 192.168.1.4/30
3. 192.168.1.8/30
4. 192.168.1.96/30
5. 192.168.1.138/30
6. 192.168.1.190/30
Cisco 3 - Classless
Page 904/20/23
Module 1
How does a router know of paths to destination networks? (Choose two.)
1. inspection of the destination IP address in data packets
2. ARP requests from connected routers
3. manual configuration of routes
4. updates from other routers
5. DHCP information broadcasts
6. updates from the SMTP management information base
Cisco 3 - Classless
Page 1004/20/23
Module 1
How does a router know of paths to destination networks? (Choose two.)
1. inspection of the destination IP address in data packets
2. ARP requests from connected routers
3. manual configuration of routes
4. updates from other routers
5. DHCP information broadcasts
6. updates from the SMTP management information base
Cisco 3 - Classless
Page 1104/20/23
Module 1
Refer to the network shown. How will Router1 summarize and advertise the four networks attached to its Ethernet ports?
1. 172.16.16.0/20
2. 172.16.19.0/20
3. 172.16.16.0/20 and 172.16.19.0/20
4. 172.16.16.0/22
5. 172.16.18.0/24
6. 172.16.0.0/24
Cisco 3 - Classless
Page 1204/20/23
Module 1
Refer to the network shown. How will Router1 summarize and advertise the four networks attached to its Ethernet ports?
1. 172.16.16.0/20
2. 172.16.19.0/20
3. 172.16.16.0/20 and 172.16.19.0/20
4. 172.16.16.0/22
5. 172.16.18.0/24
6. 172.16.0.0/24
Cisco 3 - Classless
Page 1304/20/23
Module 1
In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
1. 3
2. 4
3. 12
4. 36
5. 84
6. 180
Cisco 3 - Classless
Page 1404/20/23
Module 1
In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
1. 3
2. 4
3. 12
4. 36
5. 84
6. 180
Cisco 3 - Classless
Page 1504/20/23
Module 1
A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
1. /31
2. /30
3. /29
4. /28
5. /27
6. /26
Cisco 3 - Classless
Page 1604/20/23
Module 1
A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
1. /31
2. /30
3. /29
4. /28
5. /27
6. /26
Cisco 3 - Classless
Page 1704/20/23
Module 1
Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
1. 32-bit address
2. next hop router interface
3. subnet mask
4. unicast host address
5. Layer 2 address
Cisco 3 - Classless
Page 1804/20/23
Module 1
Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
1. 32-bit address
2. next hop router interface
3. subnet mask
4. unicast host address
5. Layer 2 address
Cisco 3 - Classless
Page 1904/20/23
Module 1
Which of the following is a summarization address for the networks 172.21.136.0/24 and 172.21.143.0/24?
1. 172.21.136.0/21
2. 172.21.136.0/20
3. 172.21.136.0/22
4. 172.21.136.0/2
Cisco 3 - Classless
Page 2004/20/23
Module 1
Which of the following is a summarization address for the networks 172.21.136.0/24 and 172.21.143.0/24?
1. 172.21.136.0/21
2. 172.21.136.0/20
3. 172.21.136.0/22
4. 172.21.136.0/2
Cisco 3 - Classless
Page 2104/20/23
Module 1
An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
1. 192.1.1.16/26
2. 192.1.1.96/28
3. 192.1.1.160/28
4. 192.1.1.196/27
5. 192.1.1.224/28
6. 192.1.1.240/28
Cisco 3 - Classless
Page 2204/20/23
Module 1
An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
1. 192.1.1.16/26
2. 192.1.1.96/28
3. 192.1.1.160/28
4. 192.1.1.196/27
5. 192.1.1.224/28
6. 192.1.1.240/28
