- 1 -

SUBARU OUTBACK WHEEL ARCH TRIM

EN

WHEEL ARCH TRIM

E2010AL000; OUTBACK ‘15MY~

INSTALLATION INSTRUCTION

Heptane

Wipe with cleaning agent and shop cloth.

If the outdoor temperature is 15°C or lower, warm between 30°C and 50°C.

24Hrs

Avoid washing the car for 24 hours.

- 2 -

SUBARU OUTBACK WHEEL ARCH TRIM

Component partsNo. Part Description Quantity No. Part Description Quantity(1) Arch trim F bumper RH 1 (10) Arch trim R bumper LH 1(2) Arch trim F bumper LH 1 (11) Metal clips 10(3) Arch trim F fender RH 1 (12) Metal clips (R door) 4(4) Arch trim F fender LH 1 (13) Metal clips (R fender) 4(5) Arch trim R door RH 1 (14) Garnish clips 2(6) Arch trim R door LH 1 (15) Bolts (with attached washer) 2(7) Arch trim R fender RH 1 (16) J nut 2(8) Arch trim R fender LH 1 (17) Protective tape (12-piece sheet) 1 set(9) Arch trim R bumper RH 1 (18) Sealing tape (2-piece sheet) 1 set

(11)(11) (16)(16)

(17)(17)

(18)(18)

(1)(1)

(3)(3)

(7)(7)

(9)(9) (5)(5)

(12)(12)

(13)(13)

(14)(14)

(15)(15)

(2)(2)

(4)(4)

(8)(8)

(10)(10)(6)(6)

Required tools

Figure illustrating completed installation

8mm8mm

－＋

RearFront

- 3 -

SUBARU OUTBACK WHEEL ARCH TRIM

WHEEL ARCH TRIM FRONT installation proceduresThis figure depicts installation on the LH side.Install the product on the RH side in the same way.

1. Align the positions of the front end of the wheel arch trim and the end of the F fender.

Reference diagram for F fender part marking

(4)

Markings (2 locations)

(Parts with protective tape affixed)

2. Remove the wheel arch trim and, using the markings as guides, affix the protective tape (17).

(17)

1

2

3. Peel back the double-sided tape liners on the wheel arch trim: (4) from front, (2) from above, and affix masking tape to the product outer surface side.

Front(4)

NOTE: - The tape liner is doubled on the wheel arch trim (4). Pull off both tape liners toward the outer peripheral side.

4. Temporarily affix the wheel arch trim (2) and (4) to the car body.

(4)

(2)

Affix in the order from (4) to (2).

3

4

- 4 -

SUBARU OUTBACK WHEEL ARCH TRIM

5. Align the gaps in (4) and (2) to the gaps in the car body parts.

(4)(2)

6. Insert the metal clips until the tabs catch, and confirm that the clips do not rattle

(11)

(2)

(4)

(11)

(2) (4) OK NG

5

6

7. Pressure-fix (2) and (4) to the car body while pulling out the double-sided tape liners in the order shown.

2

3

6

7

1

5 4

Pressure-fixed

Pressure-fixed

Pressure-fixed

7

- 5 -

SUBARU OUTBACK WHEEL ARCH TRIM

WHEEL ARCH TRIM REAR installation procedures

1. Remove the garnish.

Side sill garnish

* Peel off the tape remaining on the car body and clean the area underneath.

Rear quarter garnish

Discard

2. Affix the sealing tape (18) over the upper hole.

3. Press the wheel arch trim (6) and (8) to the installation position, and hold it in place temporarily with masking tape.

R fender part markings: 2 locations

R door part markings: 2 locations

(6)

(8)

After the completion of marking, cut the tape along the car divider.

To align the positions of the R door part and the R fender part, affix masking tape to the top surface side.

Align the positions of the end of the wheel arch trim and the end of the R fender.

8

(18)

9

10

4. Using the holes for installation and the shape of the seating face as guides, make markings with the water-based marker.

R fender (2 locations)

R door(2 locations)

5. Remove the wheel arch trim and, using the markings as guides, affix the protective tape (17).

Markings

Protective tape

Tape affixing position on the R door part

(17)

(17)

(14)

(8)

11

12

13

- 6 -

SUBARU OUTBACK WHEEL ARCH TRIM

6. Peel back the double-sided tape liners on the wheel arch trim: (6) and (8) from back, (10) from above, and affix masking tape to the product outer surface side.

Front(8)

NOTE: - From the divider side, peel off toward the end. - Peel off the double-sided tape to a length of about 70mm on the general part, and 30mm on the divider part.

7. Push the mud guard into the rear section, and insert the J nut (16) into the flange part A of the rear bumper.

8. Temporarily affix the wheel arch trim (6), (8), and (10) to the car body.

9. First, affix part A temporarily using bolts (washer) (15).

(6)

(8)

(10)

Part A

(15)

(16)

10. Confirm that the divide between (6) and (8) is as shown in the figure below.

14

15

(6) (8)

Open and close the door to confirm that there is no interference between (6) and (8).

Align with end of R fenderAlign with end of R door

16

11. Align the gaps in (8) and (10) to the gaps in the car body parts.

12. Insert the metal clips until the tabs catch, and confirm that the clips do not rattle.

・ For R fender part only・ For F bumper part・ For F fender part・ For R bumper part

・ For R door part only

(12)

(13)

(11)

(8)

(6)

(10)

(11) (13)

Wheel Arch Trim (6)

OK NG

OK NG

(12)

(8) (10)17

18

19

- 7 -

SUBARU OUTBACK WHEEL ARCH TRIM

13. Tighten the bolts (15) of part A.NOTE:

- Torque: 20 ±0.2 N·m (20 ±2 kgf·cm)

14. Pressure-fix (6), (8), and (10) to the car body while pulling out the double-sided tape liners in the order shown.

1 63

5

4

7

2

Pressure-fixed

Pressure-fixed

Pressure-fixed

(6)

(8)

(10)

15. Attach the garnish that was removed in the first step (1) to the car body.

20