Wetting behavior of Sn–Ag–Cu and Sn–Bi– alloys: insights · est became practical. Three...
Transcript of Wetting behavior of Sn–Ag–Cu and Sn–Bi– alloys: insights · est became practical. Three...
S
Wi
Ba
b
c
a
A
R
A
A
K
S
S
W
T
1
AfSgrih[
ds
h2a
j m a t e r r e s t e c h n o l . 2 0 1 9;8(1):1581–1586
www.jmrt .com.br
Available online at www.sciencedirect.com
hort Communication
etting behavior of Sn–Ag–Cu and Sn–Bi–X alloys:nsights into factors affecting cooling rate
ismarck L. Silvaa, Amauri Garciab, José E. Spinelli c,∗
Department of Materials Engineering, Federal University of Rio Grande do Norte-UFRN, 59078-970 Natal-RN, BrazilDepartment of Manufacturing and Materials Engineering, University of Campinas-UNICAMP, 13083-860 Campinas-SP, BrazilDepartment of Materials Engineering, Federal University of São Carlos-UFSCar, 13565-905 São Carlos-SP, Brazil
r t i c l e i n f o
rticle history:
eceived 8 March 2018
ccepted 13 June 2018
vailable online 5 November 2018
eywords:
older alloys
a b s t r a c t
Based on two experimental approaches: transient directional solidification and drop shape
analyses, the measurements of cooling rates and contact angles (�) of several solders of inter-
est became practical. Three Sn–0.7Cu–(1; 2 and 3Ag) and four Sn–34Bi–(0Cu; 0.1Cu; 0.7Cu;
2Ag) alloys are investigated to determine their wetting behavior, compare to each other and
bring to light their ability (or not) to control the initial cooling rate. In the case of SAC alloys,
increase in Ag means decrease in both � and cooling rate. An opposite correlation between
cooling rate and � is observed when Sn–34Bi and the Sn–34Bi–0.1Cu alloys are compared.
olidification
ettability
hermal analysis
© 2018 Brazilian Metallurgical, Materials and Mining Association. Published by Elsevier
Editora Ltda. This is an open access article under the CC BY-NC-ND license (http://
creativecommons.org/licenses/by-nc-nd/4.0/).
. Introduction
mong the candidates to replace Sn–Pb solders, two Snamilies of eutectic alloys deserve attention: Sn–Ag–Cu andn–Bi–(Ag,Cu) alloys. Sn–Ag–Cu alloys have advantages ofood wettability, superior interfacial properties, high creepesistance, and low coarsening rate [1,2]. Sn–Bi based soldersn the electronic packaging have shown good joint strength,igh creep resistance and low coefficient of thermal expansion
3,4].
Wettability (contact angle – �) is a key property of sol-er alloys. It affects the capability of heat to flow across theolder/substrate interface, which directly contributes to the
∗ Corresponding author.E-mail: [email protected] (J.E. Spinelli).
ttps://doi.org/10.1016/j.jmrt.2018.06.016238-7854/© 2018 Brazilian Metallurgical, Materials and Mining Assocrticle under the CC BY-NC-ND license (http://creativecommons.org/lic
evolution of solidification [5,6]. � values corresponding to theinitial stages of wetting have been related to the interfacial sol-der/substrate heat transfer coefficient (hi) [7,8]. Consequently,the magnitude of the cooling rate (T) in the first stages of solid-ification may be affected. To the best of the present authors’knowledge, until recently, no systematic studies relating � andT of solders were published.
Here T can be analytically described as a function of sol-der/substrate parameters and other operational conditions [9]and consequently, as a function of hi:
T =[
m(Tp − TLiq)√
�.˛SL�2[1 − erf (m�2)] exp(m�2)2
]
[2˛SL�2
2
((2KS�2(TSol − T0))/(n√
�(TLiq − T0) exp(�21)[M + erf (�1)]hi)) + SL
]2
(1)
iation. Published by Elsevier Editora Ltda. This is an open accessenses/by-nc-nd/4.0/).
o l .
1582 j m a t e r r e s t e c h nwhere ˛SL: thermal diffusivity of the alloy mushy zone, �1 and�2: solidification constants associated with the displacementof solidus and liquidus isotherms, respectively, KS: solid thermalconductivity, TSol: non-equilibrium solidus temperature, T0:room temperature, TLiq: liquidus temperature, Tp: initial melttemperature, m: square root of the ratio of thermal diffusivitiesof mushy zone and liquid, (˛SL/˛L)1/2, M: ratio of heat diffusivi-ties of solid solder and substrate material, (kScM�M/kMcS�S)1/2,n: square root of the ratio of thermal diffusivities of solid andmushy zone, (˛S/˛SL)1/2, and SL: position of liquidus isothermfrom the solder/substrate interface.
As described in Eq. (1), beyond hi other alloy properties playa part on T, such as the latent heat of fusion, thermal conduc-tivity, density and specific heat. These properties vary withincreasing alloy solute content, whereas minor additions arenot expected to change them noticeable.
Some previous studies identified that additions of Agaffect the wettability of the Sn–Cu eutectic alloy [10,11].Higher Ag contents produced better wettability by lower-ing wetting time and increasing maximum wetting force.Zang et al. [12] showed that the addition of 1.0 wt.% Cudid not influence decisively the wettability of the Sn–58Bisolder.
The present contribution aims to determine �, by usinga goniometer, and T by transient directional solidification ofvarious SAC and Sn–Bi based alloys. The results of � for thewetting first stages will be correlated with T. The relative sig-nificance of � and alloy solute content on T will be outlined.Moreover, for both families of alloys, the effects of varying
third solute contents (Ag/Cu) on the wetting behavior will beexamined.Controller andsamplethermocouples Thermal insula
Temperaturecontroller
Data logger
PC
Opticalsystem
Fig. 1 – Goniometer apparatus used to determine the form of me�e: equilibrium contact angle).
2 0 1 9;8(1):1581–1586
2. Experimental procedure
Three Sn–0.7Cu–(1; 2 and 3Ag) and four Sn–34Bi–(0Cu; 0.1Cu;0.7Cu; 2Ag) (wt.%) alloys were used in both molten metalshape analysis and solidification experiments. The transientdirectional solidification experiments allowed T to be deter-mined in the solidification first stages. A water-cooled carbonsteel bottom mold allowed heat to flow downwards insidethe system, while growth occurred upwards. The transientdirectional solidification method refers to a well-known exper-imental setup, as detailed elsewhere [13]. The melt superheatwas established as 10% above the liquidus temperature of eachalloy at the beginning of each experiment. Once started thecooling procedure, temperatures referring to positions veryclose to the solder/substrate interface were acquired. For that,a fine thermocouple positioned at 3–4 mm from the bottompart of the mold was required. J type thermocouple stainlesssteel probes with 500 mm of length and 1.5 mm of diameterwere employed.
A goniometer Krüss DSHAT HTM Reetz GmbH modelallowed the measurement of � for each solder alloy/carbonsteel substrate (Fig. 1). The surfaces of the substrates used inthe goniometer had the same finishing as that employed dur-ing directional solidification, that is #1200 grind paper. Thedata of the tests were all developed in triplicate. The equip-ment is able to follow continuously the form of the droplet,which is expressed by contact angles. For each alloy, constantheating rate of 10 K/min and a natural cooling rate inside the
furnace were carried out. Two different periods of the exper-imental scatter will be considered: initial instants (first 45 s)tion chamberOn-off valveand flowmeter
Argoncylinder
Alloy sample
1020 carbonsteel substrate
Solder flux
t1 t2 t3
θI
t1 < t2 < t3
θe
tallic molten droplets (t: time; �I: initial contact angle and
j m a t e r r e s t e c h n o l . 2 0 1 9;8(1):1581–1586 1583
SAC107 SAC107
SAC207
SAC307SAC307
SAC207
Carbon steel substrate
Carbon steel substrate
Carbon steel substrate
Carbon steel substrate
Carbon steel substrate
Carbon steel substrate3mm
3mm
3mm
3mm
3mm
3mm
15s
15s
600s
600s
600s
F on Ad
rr
3
FiaVeat
Seuossfab
ig. 2 – Advancing contact angles of the SAC alloys droplets
uring the wetting tests.
eferred �I; and ending part of the curves when an equilibriumegime is achieved (last 45 s).
. Results and discussion
igs. 2 and 3 show the variations of the molten shape dur-ng the wetting test performed with the SAC and Sn–Bi basedlloys considering two wetting times, which are 15 and 600 s.alues of both �I and �e were automatically determined forach alloy through the tangent method 2 of the drop shapenalyzer. It is worth noting that the contact angles for higherimes are lower than those observed for the first wetting times.
Fig. 4 shows the experimental profiles of � vs. time for then–Ag–Cu alloys. The values of both �I and �e determined forach alloy are shown in Table 1 related to experimental T val-es. It is worth noting in Fig. 4 that some fluctuations haveccurred in the initial stages when the melt was not able topread, and convection flows may occur. Also, a period of con-
tancy is achieved for higher wetting times. �I determinedor the Sn–0.7Cu–1.0Ag, Sn–0.7Cu–2.0Ag and Sn–0.7Cu–3.0Aglloys are 36.7◦, 33.9◦ and 32.1◦, respectively, that is, the wetta-ility improves as the alloy Ag content is increased. The relatedISI 1020 steel surface showing the molten’s shape and size
T show the same tendency of �I as the Ag content increases.Here, a decrease in �I adheres to a decrease in T. Very differentamounts of Ag may result in variation of alloy properties suchas thermal diffusivity and latent heat of fusion. Consequently,these properties interfere in the evolution of solidification ofthe alloy, that is, in T.
The eutectic volume fractions are 35%, 45%, and 61% for theSn–0.7Cu–1.0Ag, Sn–0.7Cu–2.0Ag and Sn–0.7Cu–3.0Ag alloys,respectively [14]. This explains the presumed variations inparameters/properties denoted in Eq. (1) with the increasein Ag alloying. The same tendency of improving wettabilitywith increasing Ag content has been reported [10,11], how-ever, these studies have not focused on a significant range ofAg alloying in SAC alloys, as is the case of the present investi-gation.
The results � vs. time for Sn–34Bi–X alloys can be seenin Fig. 5, and in Table 1 with the corresponding T. For facili-tate the visualization, detailed inlet plots encompassing thewetting behavior in the first 100 s have been inserted. By
comparing the measurements for the Sn–34Bi alloy withthose for the Sn–34Bi–0.1Cu alloy, it is possible to infer thatthe Sn–34Bi–xCu alloys are sensitive to small copper addi-tions. Smaller �I (�I = 27.8◦) associated with higher T (12.3 K/s)1584 j m a t e r r e s t e c h n o l . 2 0 1 9;8(1):1581–1586
Sn-34wt.%BiSn-34wt.%Bi
Carbon steel substrate3mm
Carbon steel substrate3mm
15s
Sn-34wt.%Bi-0.1wt.%Cu Sn-34wt.%Bi-0.1wt.%Cu
Sn-34wt.%Bi-0.7wt.%Cu
Sn-34wt.%Bi-0.2wt.%Ag Sn-34wt.%Bi-0.2wt.%Ag
Sn-34wt.%Bi-0.7wt.%Cu
Carbon steel substrate Carbon steel substrate
Carbon steel substrate Carbon steel substrate
Carbon steel substrate Carbon steel substrate
3mm
3mm 3mm
3mm3mm
3mm
15s
15s
15s
600s
600s
600s
600s
Fig. 3 – Advancing contact angles of the Sn–Bi–X alloys droplets on AISI 1020 steel surface showing the molten’s shape and
size during the wetting tests.characterize the Sn–34Bi–0.1Cu alloy. This is because verysmall additions of Cu are not expected to change the alloyproperties (e.g., the latent heat of fusion, thermal conductiv-ity, density and specific heat) and parameters (e.g., solidus andliquidus temperatures) governing T. In this case, T is controlledby �I, i.e., by hi (lower �I > higher hi > higher T, according toEq. (1)).
The additions of 0.7Cu and 2.0Ag decreased and increased
�I, respectively, as compared to the binary Sn–34Bi alloy. Incontrast, T values are quite close. It appears that a compen-sation between �I and the thermophysical properties of thesemodified alloys (i.e., Sn–34Bi–0.7Cu and Sn–34Bi–2.0Ag) occurs,which is conducive to a similar initial solidification progressas compared to that of the binary Sn–34Bi alloy.
4. Conclusions
It has been shown that despite the importance of �I as a signif-
icant factor affecting soldering cooling rate, with the increasein solute additions to the solder alloys, the thermophysicalproperties can play a role that can gradually be even moresubstantial than that exercised by �I. Based on that, a generalj m a t e r r e s t e c h n o l . 2 0 1
0 100 200 300 400 500 600 700 8005
10
15
20
25
30
35
40
45
50
55
60
0 10 20 30 40 50 60 70 80 90 10020
25
30
35
40
45
50
First 100s
θ, C
onta
ct A
ngle
(°)
Time (s)
Sn-0.7Cu-1.0Ag - SAC 107Sn-0.7Cu-2.0Ag - SAC 207Sn-0.7Cu-3.0Ag - SAC 307
Fig. 4 – Evolution of � between SAC alloys and the AISI 1020steel substrate.
Table 1 – � and T for the tested SAC and Sn–34Bi–Xsolder alloys solidified against a carbon-steel substrate.
Solder alloy �I (◦) – initial �e (◦) – equilibrium T (K/s)a
Sn–34wt%Bi 39.2 ± 2.8 23.0 ± 1.1 10.0Sn–34wt%Bi–0.1wt%Cu 27.8 ± 4.0 15.8 ± 0.1 12.3Sn–34wt%Bi–0.7wt%Cu 34.7 ± 1.3 22.5 ± 0.9 8.0Sn–34wt%Bi–2.0wt%Ag 42.9 ± 1.0 35.8 ± 0.1 9.0SAC107 36.7 ± 0.2 21.4 ± 0.5 32.0SAC207 33.9 ± 0.7 18.8 ± 1.1 16.0SAC307 32.1 ± 3.4 22.2 ± 0.2 9.5
a Determined based on the nearest thermocouple to thealloy/substrate interface.
0 100 200 300 400 500 600 700 8005
10
15
20
25
30
35
40
45
50
55
60
65
0 10 20 30 40 50 60 70 80 90 10 020
25
30
35
40
45
50
55First 100 s Sn-34Bi
Sn-34Bi-0.1Cu Sn-34Bi-0.7Cu Sn-33Bi-2Ag
θ, C
onta
ct A
ngle
(°)
Time (s)
Fig. 5 – Evolution of � between Sn–34Bi–X solder alloys andt
tp
1
r
he AISI 1020 steel substrate.
rend cannot be established between �I and T, as shown by theresent results:
. Sn–0.7Cu–Ag alloys: Both �I and T were shown to decreaseas the Ag content was increased: lower �I > higher hi < lowerT. According to the analytical Expression (1) for T, this wasshown to be associated with variations in thermophysical
9;8(1):1581–1586 1585
properties with the increase in Ag content, as also sup-ported by previous studies.
2. Sn–34Bi–X alloys: A small addition of Cu (X = 0.1Cu) was notexpected to change the alloy thermophysical properties,however, this has induced a smaller �I, which controlledT : lower �I > higher hi > higher T, according to Eq. (1) for T.
The additions of 0.7Cu and 2.0Ag to the Sn–34Bi alloy wereshown to decrease and increase �I, respectively, as com-pared to the binary Sn–34Bi alloy. In contrast, T remainedclose for these alloys, suggesting that a compensatingeffect exists between �I (and consequently hi) and thethermophysical properties, which is conducive to similarcooling rate, T.
Conflicts of interest
The authors declare no conflicts of interest.
Acknowledgements
The authors thank the financial support provided by FAPESP(São Paulo Research Foundation, Brazil: grants 2017/15158-0 and 2017/12741-6), CNPq and the Postgraduate Program inMaterials Science and Engineering (PPGCEM-UFRN).
e f e r e n c e s
[1] Xu S, Habib AH, Pickel AD, McHenry ME. Magneticnanoparticle-based solder composites for electronicpackaging applications. Prog Mater Sci 2015;67:95–160.
[2] Keller J, Baither D, Wilke U, Schmitz G. Mechanical propertiesof Pb-free SnAg solder joints. Acta Mater 2011;59:2731–41.
[3] Braga MH, Vizdal J, Kroupa A, Ferreira J, Soares D, MalheirosLF. The experimental study of the Bi–Sn, Bi–Zn and Bi–Sn–Znsystems. CALPHAD 2007;31:468–78.
[4] Shalaby RM. Effect of silver and indium addition onmechanical properties and indentation creep behavior ofrapidly solidified Bi–Sn based lead-free solder alloys. MaterSci Eng A 2013;560:86–95.
[5] Cheung N, Santos NS, Quaresma JMV, Dulikravich GS, GarciaA. Interfacial heat transfer coefficients and solidification ofan aluminum alloy in a rotary continuous caster. Int J HeatMass Transf 2009;52:451–9.
[6] Abtew M, Selvaduray G. Lead-free solders inmicroelectronics. Mater Sci Eng R 2000;27:95–141.
[7] Santos WLR, Silva BL, Bertelli F, Spinelli JE, Cheung N, GarciaA. An alternative thermal approach to evaluate thewettability of solder alloys. Appl Therm Eng 2016;107:431–40.
[8] Silva BL, Bertelli F, Canté MV, Spinelli JE, Cheung N, Garcia A.Solder/substrate interfacial thermal conductance andwetting angles of Bi–Ag solder alloys. J Mater Sci MaterElectron 2016;27:1994–2003.
[9] Quaresma JMV, Santos CA, Garcia A. Correlation betweenunsteady-state solidification conditions, dendrite spacings,and mechanical properties of Al–Cu alloys. Metall MaterTrans A 2000;31:3167–78.
[10] Pandher R, Lawlor T. Effect of silver in common lead-free
alloys. In: ICSR (soldering and reliability) conferenceproceedings. 2009.[11] Dharma IGBB, Hamdi M, Ariga T. The effects of adding silverand indium to lead-free solders. Weld J 2009;88:45–8.
o l .
1586 j m a t e r r e s t e c h n[12] Zang L, Yuan Z, Zhao H, Zhang X. Wettability of moltenSn–Bi–Cu solder on Cu substrate. Mater Lett 2009;63:
2067–9.[13] Reyes RV, Bello TS, Kakitani R, Costa TA, Garcia A, Cheung N,et al. Tensile properties and related microstructural aspectsof hypereutectic Al–Si alloys directionally solidified under
2 0 1 9;8(1):1581–1586
different melt superheats and transient heat flowconditions. Mater Sci Eng A 2017;685:235–43.
[14] Spinelli JE, Silva B, Garcia A. Assessment of tertiary dendriticgrowth and its effects on mechanical properties ofdirectionally solidified Sn–0.7Cu–xAg solder alloys. J ElectronMater 2014;43:1347–61.