Welcome to STRAP Software Presentation · 2020. 6. 28. · Design of composite structures Cold...
Transcript of Welcome to STRAP Software Presentation · 2020. 6. 28. · Design of composite structures Cold...
-
STRAP Software Presentation
Welcome to
-
STRAP Software for
➢ RC structures design, detailing and scheduling.
➢ Design & Optimization of steel structures
➢ Design of composite structures➢ Cold formed steel design➢ Analysis of Bridges➢ Design of water retaining
structures➢ Post tensioning for beams & slabs
-
STRAP For RC Designers
Fully Automatic and Integrated
system for RC Structure design,
detailing and construction
drawing production with BBS
www.ramcadds.com
-
STRAP For RC Designers
RC Frames + Shear walls + Lift
cores + Flat slabs + Raft
Modeling .. All in one system
-
STRAP For RC Designers
Special Features for Shear Wall Modeling
Any complicated shear
wall/ lift core section can
be defined in single step
Automatic generation of rigid links
for efficient load transfer
Program automatically generates additional beams, where ever
coupling beams are defined for proper moment transfer
-
STRAP For RC Designers
➢ Possibility to define opening in the shear wall
➢ Automatic creation of nodes when wall section changes
➢ Change the wall section by moving the node in the main geometry
Special Features for Shear Wall Modeling
-
STRAP For RC Designers
FE Modeling is very SimpleUser controlled
mesh sizeAutomatic
meshing
Automatically
aligns with
existing nodes
Automatically aligns with
adjacent elements
-
STRAP For RC Designers
Beam design and detailing
Reinforcement for beams for
the moment at the face of
the column. Considerable
savings on reinforcement.
Program automatically
detects continuous beams
Cost effective designs
-
STRAP For RC Designers
Automatic Calculation
of effective length factors
Automatic
Detection of un supported
lengths for column design.
Automatic detection unsupported lengths
-
STRAP For RC Designers
RC Column Design features
➢Design for any shaped cross sections
➢Automatic Optimization of reinforcement
for a given cross section.
➢The column capacity calculation is exact.
Program calculates neutral axis and stress
& strain in each bar from neutral axis.
➢Reinforcement can be grouped for different
levels and different columns.
➢Graphical Display of reinforcement and column
capacity factor.
User can specify the
reinforcement in the
column
-
STRAP For RC Designers
Reinforcement can be changed after
detailing. The program automatically
checks for codal provisions.
Automatic drawing
of cross sections
Graphical
display of
Envelope of
Required Rft
Beam Detailing
-
STRAP For RC Designers
BBS and quantity estimation
Total quantity
All standard shape
codes are available.
In addition to that
user can add their
own shape codes.
Automatic scheduling &
quantity calculation
-
STRAP For RC Designers
Column detailing & BBS
Detail and draw all
columns
in tabular formatAutomatically calculates
bar schedule for the total
drawing
Automatically draws
elevation & Cross
Section for selected
column
-
STRAP For RC Designers
SLAB detailing &
BBS
-
STRAP For Steel Designers
Steel Design/Optimization
If you are serious in designing Least Cost Steel
Structures then STRAP is the best choice for you.
-
STRAP For Steel Designers
➢ The shapes can be arbitrary combinations of standard steel sections, plates and sections defined by dimensions.
➢ Above arbitrary shape can be designed in steel post processor
User defined steel section shapes
-
STRAP For Steel Designers
➢ Slender sections can be designed as per Indian code
➢ Design of castellated and cellular beams
➢ Spilt beam with tapered section. Program automatically creates new sections at the new intermediate nodes for a tapered beam
Design of slender sections
-
STRAP For Steel Designers
Automatic Calculation
of unsupported lengths
Design of single/ star
angles about principal
axis.
Automatic detection unsupported lengths
-
STRAP For Steel Designers
COMPOSITE SECTIONS
➢Calculation of shear studs
➢Partial shear connection
➢Design for wet concrete condition
➢Calculation of short term and long
term deflections
➢Option to account for negative
moment reinforcementComposite column
and beam design
Analysis and design of composite columns and beams
-
For Transmission Tower Designers
➢IS 802 is available for tower design
➢Automatic generation of wind load on towers/ Open
structures.
➢Different cost factors can be assigned to various section
types or member groups.
➢Selection of sections can be subject to user constraints.
Specify the deflection or drift, program automatically
optimizes the whole structure
- Engineer can get the least cost structure using STRAP!!!
For Cost Optimization
STRAP For Steel Designers
-
STRAP For Steel Designers
Automatic GA drawing preparation and quantity
calculations.
Export through DXF
to any cad programs.
-
STRAP For Steel Designers
Automatic design of steel connections
➢ Beam to beam
➢ Column web to Beam
➢ Column Flange to Beam
➢ Column base plate design
➢ Design for AISC, BS & Euro Code
-
STRAP For Steel Designers
➢Design for AISI, BS and Euro codes
➢New section types can be added to the
library by defining the basic dimensions only.
➢Calculation of torsional flexural buckling for
LTB
➢Design for reduced section according to the
web thickness/depth ratio
➢Hot rolled sections can be used in the same
model.
➢To define new sections apart from standard,
CROSEC module is necessary.
For Cold Formed Steel DesignersStandard Sections + user can create customized sections
We recommend
STRAP + Cold formed+ CROSEC for cold formed steel
designers
Simple to most complicated sections can be
analyzed and designed.
-
➢Appendix A - "Calculation of minimum
reinforcement, crack spacing and crack widths in
relation to temperature and moisture effects“
➢Appendix B - "Calculation of crack widths in
mature concrete“ - The program calculates the
reinforcement required to satisfy moment/
force requirements
STRAP For Water retaining structures
-
➢ Automatic calculation of nodal weights
➢ Simple to define rigid diaphragm actions
➢ Inbuilt response spectra for various damping ratios
➢ Possibility to use site spectra
➢ Automatic scaling of response spectrum results
➢ Option to define eccentricities at various levels
➢ Assign to the CQC the signs of the results calculated for the dominant mode shape
STRAP Earthquake Analysis
-
➢ The storey drift in any storey shall not exceed 0.004 times the storey height
STRAP Earthquake AnalysisStorey drift calculations
-
STRAP 2012 – New features
➢ Program will list centre of mass and centre of rigidity for each floor.
STRAP Earthquake AnalysisRigidity & mass centre
-
Storey Shear & Moments
STRAP Earthquake Analysis
-
Stability coefficient (Theta)➢ P-Delta effects on story shears and moments are not
required to be considered where the stability coefficient (Theta ) is equal to or less than 0.10"
STRAP Earthquake Analysis
-
Weak Stories Calculation➢ A weak storey is one in which the storey lateral
strength is less than 80% of that in the storey above
STRAP Earthquake Analysis
-
Soft Storey Calculation➢ A soft storey is one in which the lateral stiffness is less than
70% of that in the storey above or less than 80% of the average lateral stiffness of the three storeys above
➢ the columns and beams of the soft storey are to be designed for 2.5 times the storey shears and moments calculated under seismic loads
STRAP Earthquake Analysis
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
Models from Users
-
STRAP 2012 – New features
Models from Users
-
Models from Users
-
Models from Users
-
For more information contact us at [email protected]
Ram Caddsys Pvt. Ltd.A8, Vaigai Apartments4, Giri Street, Westmambalam,Chennai, India. Zip: 600 033.Tel: 00-91-44-2474 7738 /Email: [email protected]: www.ramcadds.in
mailto:[email protected]://www.ramcadds.in/