Welcome Step 1: Connect your telephones

Welcome to your new Mitel 1000. Your pack should contain the items pictured below. These instructions show you how to connect telephones and the telephone line to the system so you can make and receive calls.

They also show how to connect to the Internet over your DSL Line so you can browse the web, use email or even make telephone calls over the Internet.

A) If your Mitel 1000 came with a Featurephone please plug this into the EXTN 20 socket on the back of the Mitel 1000. Otherwise plug a standard phone into the EXTN 20 socket.

It is possible to connect up to three other phones to the Mitel 1000. These should be plugged into any remaining extension sockets. (EXTN 21-23).

B) Plug the Line Cable (grey) into the Line 1 socket on the back of the Mitel 1000.

C) Fit the Cable Cover over the phone connections.

Step 1 continued

D

F

Step 2: Connect to the Internet Step 2 continued

Featurephone *

1 Cable Cover

1 Documentation Pack(1 CD incl. Owner’s Manual)(1 Phone Quick Reference Guide)(1 Fast Installation Guide)

1 Power Supply Unit

2 Line Cables (grey)

1 DSL Cable (purple)

DECT Handset &Charger *(Includes separateinstruction sheet)

1 Mitel 1000 System

1 LAN Cable (yellow)

1 ADSL splitter

1 2 3 4 5

D) Plug the other end of the Line Cable (grey) into the phone connector of the splitter supplied with your DSL service. Plug the splitter into the wall telephone outlet.

Plug one end of the DSL cable (violet) into the ADSL Modem connector of the splitter supplied with your DSL sevice.

E) Connect the other end of the DSL cable (violet) to the DSL connector of your Mitel 1000.

F) Connect the Power Supply Unit to the Mitel 1000 and the mains power outlet.

Wait approximately one minute for the system to initialise. You can now make telephone calls.

***Do not proceed beyond this stage until calls can be made and received***

G) Set up and register the DECT Handset (s) that are supplied with your Mitel 1000 by following the instructions supplied with the handset.

NOTE: After powering on the DECT Handsets for the first time, the batteries should be charged for 14 hours to get maximum battery performance.

NOTE: If you wish to have any of your phones located away from the Mitel 1000 please see the Owner’s Manual for cabling instructions.

NOTE: Voice features can be programmed from the Featurephone on extension 20. For instructions refer to Appendix C in the Owner’s Manual on the Documentation CD.

A) Connect the LAN Cable (yellow) from the LAN port of your PC to any of the ETHERNET sockets of your Mitel 1000 (yellow).

B) Open a web browser, such as Internet Explorer or similar, on your PC.

C) Open the Mitel 1000 Management Application by entering the following address into your web browser: http://192.168.1.1

D) Enter the Username (admin) and the Password (admin) and press OK.

D

This will open the programming interface Welcome screen.It allows you to programme the PBX and Router configurationE) To program the ADSL Modem as required.Click on the Username /

Password link on the welcome page

BA

C

E

A

A

C

Note:(If this screen does not appear, check your PC settings for automatically obtaining an “IP address” or ensure that the PROXY server setting is turned OFF.Refer to Appendix E in Owner’s Manual on the Documentation CD).

E

By default your Mitel 1000 is programmed with the PPPoA option. As an example you can see below how to continue programming this option.Note: PPPoA follows the same steps for programming as PPPoE.

RED SolidGreen FlashingGreen OFF

PowerPower or device

malfunctionPower ON - Power OFF

Ethernet -Powered device

connected to the Connection

Central LAN-

No cable connection or no powered device

DSL -DSL line

connected and synchronized.

(Occasional flicker)

DSL attempting to synchronize -

InternetUsename/Password Incorrect.

VPI/VCI Incorrect

IP connected (No traffic detected)

IP connected (Traffic detected)

DSL Line not connected

Wireless - Wireless LAN enabled

Wireless LAN activity present

Wireless LAN disabled

Step 2 continued (PPPoA or PPPoE) Step 2 continued (DHCP-RFC 1483) Step 2 continued (Manual RFC 1483) Step 3: Next steps

Enter your broadband service Username and Password.

Note: In some cases a Password may not be required. In this case just enter the Username.

Click on “Next”.

Enter the VPI and VCI settings as supplied by your broadband supplier.

Click on “Next”.

This completes the ADSL programming (PPPoA or PPPoE type).

6 7 8 9

If your broadband type is DHCP.These steps should be followed. Click on the Router Configuration option onthe welcome page/ADSL Modem/Change the ADSL Modem Settings here/ DHCP.

Select the RFC 1483 Mode that your broadband supplier has provided you with.

Click on “Next”.

Enter the VPI and VCI settings as supplied by your broadband supplier.

Click on “Next”.

This completes the ADSL programming (DHCP type).

NOTE: More information can be obtained of how to program your ADSL Modem from the Owner’s Manual.

If your broadband type is Manual (static) and you have selected this option.These steps should be followed.

Enter all the details provided by your broadband supplier in the boxes.

Click on “Next”.

There are four types of RFC1483 connection available.

Choose a connection type that has been provided by your broadband supplier.Click on “Next”.

Enter the VPI and VCI settings as supplied by your broadband supplier.Click on “Next”.

This completes the ADSL programming (Manual - RFC 1483).It may take several minutes for the DSL to synchronise.Your Mitel 1000 is ready to browse the Internet once the DSL LED has gone solid green with an occasional flicker, and the Internet LED is solid or flashing green.

A) TroubleshootingYour Mitel 1000 has an activity status panel at the front of your system. The status of the lights (LEDS) will help you see if all your connections are properly installed.

Note: If the Power led flashes red, it means Mitel 1000 is in DECT registration mode.

B) Quick Reference Guide Use this to get the most from the telephone features of your Mitel 1000. For example, you can use your Mitel 1000 to take messages when you are not available to answer your phone. (Voicemail).

C) Owner’s Manual The Owner’s Manual is contained in the Documentation CD. Use it to learn how to access the advanced capabilities of your Mitel 1000. For example, you can connect your PC to the Mitel 1000 LAN without needing to have them connected via a cable. (Wireless LAN). You can also use your Mitel 1000 to make calls over the Internet. (VoIP).

Confirm the configuration by selecting “Confirm Changes”.

If requested, press Restart

Confirm the configuration by selecting “Confirm Changes”.

If requested, press Restart

Confirm the configuration by selecting “Confirm Changes”.

LR2770.06210-2