Website: Add: Room 453,4TH Floor,East...
Transcript of Website: Add: Room 453,4TH Floor,East...
-
Mintek Abrasives & Tools Co.,LtdWebsite: www.mintektools.comAdd: Room 453,4TH Floor,East NO 62, Nongye Road, Jinshui District,Zhengzhou City, Henan Province, China.Tel: 0086-13783500893, 0086-15937195915Email: [email protected] [email protected]
-
CBN Inserts of Mintek Tools:Solid CBN Inserts、Brazed CBN Inserts
-
The Grdae Introduction of Solid CBN inserts
Email: [email protected]
Grade FuturesMain
application
Structure HV
Cutting Material Industry
Matching with other
Brand
MTN-20
● Show its excellent performance when roughing and big depth cutting. ●Updated material with wear-resistance and anti-breakage. ● 100% CBN solid sintering,All corner can be cutting edges, and entire length of edge can be used, with performance and economy futures.
High speed roughing of
cast iron, The material of hard to
cut
Solid CBN 4000-4200
Gray Cast Iron /High
chrome /High Mn-steel /High
Ni-Cr
Metallurgical Roll,Surfacing roll repair,Mine
machinery,Big gear, etc.
Sumitomo BNS800 Kyocera KBN900
MTN-60
● Show its excellent performance when roughing and big depth cutting. ●Updated material with wear-resistance and anti-breakage. ● 100% CBN solid sintering,All corner can be cutting edges, and entire length of edge can be used, with performance and economy futures.
High speed roughing of
cast iron, The material of hard to
cut
Solid CBN 4000-4200
Gray Cast Iron /High
chrome /High Mn-steel /High
Ni-Cr
Metallurgical Roll,Surfacing roll repair,Mine
machinery,Big gear, etc.
Sumitomo BNS800 Kyocera KBN900
MTN-90
●Common CBN material for all machining of Hardened steel. ● Updated material with wear-resistance and anti-breakage. ● From continuous cutting to light -middle-interrupted cutting,the stability and sharp are improved, the surface roughness are also very stable.
Hardened steel
continuous/Interrupted
Cutting
Solid CBN/Brazing CBN
tips
3900-4100
Hardened steel
Wind power bearing,
Crankshaft ,Mine machinery,Automobile
gear,etc.
Sumitomo BN2000 Kyocera KBN05M
MTN-91
●Excellent wear-resistance and heat-resistance ●High speed continuous turing and milling.●Be applied in semi-finishing and finishing of hardened steel parts, eg. Bearing steel, Mould steel, Gauge steel,Tool steel,HSS. etc material.
Hardened steel
continuous Cutting
Solid CBN/Brazing CBN
tips
3300-3500
Hardened steel
Gear,Bearing . etc.
Sumitomo BN1000 Kyocera KBN05M
-
Grade Futures Main application Structure HVCutting Material Industry
Matching with other
Brand
MTN-70
● Best suitable for high speed finish machining of cast iron. ●Realizing the high efficiency processing of sintered alloy.●Corresponding to various difficult processing materials, taking into account cast iron and hardened steel, better on heat-resistance.
Cast iron/Hardened
steel semi-
finishing/fine finishing
Solid CBN/Brazing CBN tips
3700-3900
Cast Iron/Harden
ed steel
Auto brake disc,cylinder blocks of
car engines ,cylinder liner ,Gear,
Bearing.
Sumitomo BN7000/7500
Kyocera KBN60M/900
MTN-80
●Best apply to high speed fine finishing cutting of Cast Iron, meet more than V=500m/min high speed cutting,show its excellent surface roughness and long tool life. ● Make high efficiency machining of the sintered alloy come ture.●All kinds of material of hard cutting, conclude Cast Iron and hardened steel.
Cast Iron fine finishing
Solid CBN/Brazing CBN tips
3700-4000 Cast Iron
Auto brake disc,cylinder blocks of
car engines ,cylinder liner ,Gear,
Bearing.
Sumitomo BN7000/7500
Kyocera KBN60M/900
MTN-84
●Best apply to high speed fine finishing cutting of Cast Iron, meet more than V=500m/min high speed cutting,show its excellent surface roughness and long tool life. ● Make high efficiency machining of the sintered alloy come ture.●All kinds of material of hard cutting, conclude Cast Iron and hardened steel.
Cast Iron fine finishing
Solid CBN/Brazing CBN tips
3700-4000 Cast Iron
Auto brake disc,cylinder blocks of
car engines ,cylinder liner ,Gear,
Bearing.
Sumitomo BN7000/7500
Kyocera KBN60M/900
The Grdae Introduction for Solid CBN inserts of Mintek Tools
-
The Grdae Introduction of Solid CBN Corner Inserts
Grade Fetures Main Application Structure HVCutting Material
For below Industry
S70
●Bestsuitable for high speed finish machining of cast iron.●Realizing the high efficiency processing of sintered alloy.●Corresponding to various difficult processing materials, taking into account cast iron and hardened steel, better on heat-resistance.
Cast iron/Hardened
steel semi-
finishing/fine finishing
Brazing CBN tips 3700-3900
Cast Iron/Hardened
steel
Auto brake disc,Brake
Drum,Cylinderblocks of car
engines,Cylinder liner,Gear,
Bearing.
S80
●Best apply to high speed fine finishing cutting of Cast Iron, meet more than V=500m/min high speed cutting, show its excellent surface roughness and long tool life.●Make high efficiency machining of the sintered alloy come ture.●All kinds of material of hard cutting, conclude Cast Iron and hardened steel.
Cast Iron fine finishing
Brazing CBN tips 3700-4000 Cast Iron
Auto brake disc, Brake
Drum, Cylinder blocks of car
engines, Cylinder liner, Gear, Bearing.
S90
●Common CBN material for all machining of Hardened steel.●Updated material with wear resistance and anti-breakage.●From continuous cutting to light-middle-interrupted cutting the stability and sharp are improved, the surface roughness are also very stable.
Hardened steel continuous/ Interrupted
Cutting
Brazing CBN tips 3900-4100 Hardened steel
Wind power bearing,
Crank shaft, Mine
machinery, Auto mobile
gear,etc.
S91
●Excellent wear-resistance and heat-resistance●High speed continuous turing and milling.●Be applied in semi-finishing and finishing of hardened steel parts, eg. Bearing steel, Mould steel, Gauge steel, Tool steel,HSS.etc. material.
Hardened steel continuous
Cutting
Brazing CBN tips 3300-3500 Hardened steel
Gear, Bearing. etc.
Email: [email protected]
-
Grade Fetures Main Application Structure HVCutting Material
For below Industry
CB70
●Best suitable for high speed finish machining of cast iron.●Realizing the high efficiency processing of sintered alloy.●Corresponding to various difficult processing materials, taking into account cast iron and hardened steel, better on heat-resistance.
Cast iron/Hardened steel
semi-finishing/fine finishing
Brazing PCBN tips
3700-3900
Cast Iron/Hardened
steel
Auto brake disc, Brake Drum,
Cylinder blocks of car engines, Cylinder liner,Gear,Bearing.
CB90
●Common CBN material for all machining of Hardened steel.●Updated material with wear-resistance and anti-breakage.●From continuous cutting to light-middle-interrupted cutting,the stability and sharp are improved, the surface roughness are also very stable.
Hardened steel continuous/Interrupted
Cutting
Brazing PCBN tips
3900-4100 Hardened steel
Wind power bearing, Crank shaft, Mine
machinery, Automobile gear,
etc.
CB91
●Excellent wear-resistance and heat-resistance●High speed continuous turing and milling.●Be applied in semi-finishing and finishing of hardened steel parts,eg. Bearing steel, Mould steel, Gauge steel,Tool steel, HSS.etc material.
Hardened steel continuous Cutting
Brazing PCBN tips
3300-3500 Hardened steel Gear, Bearing. etc.
The Grdae Introduction of Tipped PCBN Inserts
-
Wind Power Generation Industry
-
Bearing for Wind power
Material:20CrMnTiHardness:HRC58-62
Use solid CBN Inserts of Mintek Tools;Grade: MTN-90,MTN-60
Type and specification: RNGN120400 Chamferring:S02020
Cutting Parameter: vc=140m/min, ap=0.04mm, f=0.04mm/r;
Surface roughness: Ra=0.2---0.8
Tool life of CBN inserts:48pcs/edge
-
Material: 42CrMoHardness: HRC47-55
Grade: MTN-90 CBN inserts: RCMX090700Cutting parameter: Vc=90m/min, ap=0.5mm, f = 0.6mm/r
Mintek CBN inserts improve the efficiency by 30% and increase the life by 4 times.
Workpiece: Slewing Bearing
-
Bearing Industry
-
Work piece: Bearing
Material of Bearing:GCr15Hardness:HRC62-64Cutting type:Rounded cornerUse brazed CBN inserts of Mintek ToolsGrade:S91
Type and specification: CNGA120408 S01020
Cutting parameter:
Vc(m/min)=150-244 F(mm/rev)=0.05-0.1 ap(mm)=0.2-0.3 Cutting mode:with coolant
Tool life:100pcs/edge
-
Work piece: Bearing
Material of Bearing:Hardened steelHardness:HRC56-60Cutting position:Rounded corner, End FaceUse brazed CBN inserts of Mintek ToolsGrade:S91
Type and specification: CNGA120408Chamferring: S01020
Cutting parameter: Vc(m/min)=110~150 F(mm/rev)=0.05~0.1 ap(mm)=0.10~0.2
Cutting mode:Dry cutting mode or with coolant
Tool life:50pcs/edge
-
Compressor Industry
Cutting for the main and auxiliary bearings (flanges) need large amount of CBN inserts. Because the intermittent situation is lighter, it is easier to replace the alloy and carbide inserts.
The machining efficiency is much higher than carbide inserts, and the tool life of CBN inserts is about 5 to 6 times than carbide inserts.
-
Main and Auxiliary Bearings (Flange)Use Brazed CBN inserts of Mintek Tools:S70, S80, S84WNGA080412 Chamferring:S02020Cutting parameter: Vc(m/min)=760 F(mm/rev)=0.6 ap(mm)=1.5
Tool life of CBN Inserts: 800-1000pcs/edge
Work pieces:
Main and Auxiliary Bearings (Flange)
Material of work piece:GCR15Hardness:HRC60
-
Air conditioner compressor cylinderUse solid CBN inserts or Brazed CBN inserts;Grade: MTN-70, S70,S80, S84Type and specification:WNGN080412WNGA080412Cutting parameter: vc=260m/min, ap=1.5mm, f=0.2mm/r;
Mintek CBN inserts improve the efficiency by 50% and increase the life by 30%.
Workpiece: Compressor cylinder
Parts Machining position: End faceMaterial: HT200 (Gray cast iron)Hardness: HSD78,HB180-220
-
Work piece: CrankshaftMaterial:HT200(Gray Cast Iron)
Hardness:HB180-220
Use brazed CBN inserts of Mintek ToolsGrade of Mintek:S80, S84Type Specification: TNGA160408Chamferring:S02020/S01020
Cutting Parameter: Cutting Speed Vc=380m/min Cutting Depth Ap=2mm Feed Rate F=0.2mm/r
With Coolant,Tool life:220pcs/edge,It takes about 30 seconds to process a workpiece.
-
Mining Equipment Parts Industry
-
Work piece: Parts of Mining Machine
Material of Workpiece: Cast steelHardness:HRC58-62
Use Mintek Solid CBN inserts;Processing: Rough turning,
Cutting parameter: vc=60-100m/min, ap=1-1.5mm, f=0.3mm/r;
Grade:MTN-60
Type and specification: RNMN120400 RNMN120700
-
Work piece: Parts of crusher machine
Material of Workpiece: High-ChromiumHardness: HRC65Processing: Rough turning,
Cutting parameter: vc=30-60m/min, ap=1-2mm, f=0.4mm/r; Use Mintek solid full CBN inserts;
Grade: MTN-20, MTN-60;
Type: RNGN120400, RNMN120700
-
Work piece: Parts of Mining Industries
Processing: Rough turning, Use Mintek Solid CBN inserts;
Grade: MTN-20, MTN-60; MTN-70, MTN-80;
Type and specification: CNGN120408, CNGN120412 CNGN120416, SNGN120408 SNGN120412, SNGN120416 RNGN120400, RNGN120700.
-
Suggestion of CBN inserts for Compressor partsWork name Main and auxiliary bearings Cylinder Crankshaft
The place of cutting cylindrical, face End face, outer circle outer circle
Grade of
Mintek tools
Solid CBN inserts - - -
Brazed CBN inserts S70, S80, S84 S70, S80, S84 S70, S80, S84
Suggest type and specification
WNGA080408S02020
WNGA080416S02025
TNGA160408S02020
CNGA120412S02020
CNGA120416 S02025
DNGA150408S02020
Suggest cutting edge R(mm) 0.4-1.6 0.8-2.0 0.4-1.6
Suggest for edge type S,T S S,T
Recomand width of chamfer (mm) 0.1-0.3 0.1-0.3 0.1-0.3
Recomand angle of chamfer 15°-25° 20°-30° 15°-25°
Cutting speed Vc(m/min) 210-820 120-650 280-980
Cutting depth ap(mm) 0.2-2.5 0.2-2.5 0.2-2.5
Feed rate f(mm/r) 0.1-0.5 0.1-0.4 0.1-0.5
-
Suggestion of CBN inserts for Gear & BearingWork piece name Gear Big Gear Shaft of Gear Bearing Slewing Ring
The place of turning Bore, face cylindrical of top face cylindrical cylindrical Bore cylindrical,face,bore
Grade
solid CBN inserts
MTN-90 MTN-90
brazed CBN inserts
S90, S91 S90, S91 S90, S91 S90, S91
Suggest type
CCGW 09T304 S01020
SNGN 201020 S05020
SNGA 120408 S02020
CNGA 120412 S02020
CCGW 120408 S01020
CNGN 120412 S02020
TCGW 09T304 S01020
SNGN 150716 S05020
CNGA 120408 S02020
WNGA 080408 S02020
TCGW 09T304 S01020
RCGN 120700 S03020
Recomand cutting edge R(mm) 0.4 - 1.2 0.8 - 2.0 0.4 - 1.2 0.4 - 2.0 0.4 - 1.2 0.8 - 2.0
Shape of cutting edge S, T S S, T S, T S, T S
Recomand width of chamfer(mm) 0.1 - 0.3 0.1 - 0.3 0.1 - 0.3 0.1 - 0.3 0.1 - 0.3 0.1 - 0.5
Recomand angle of chamfer 10° - 25° 10° - 30° 10° - 25° 10° - 25° 10° - 25° 10° - 30°
Cutting speed Vc(m/min) 90 - 520 30 - 120 80 - 560 80 - 480 70 - 480 50 - 220
Depth of cutting ap(mm) 0.05 - 0.5 1 - 10 0.05 - 0.5 0.05 - 0.5 0.05 - 0.5 0.1 - 1
Feed rate f(mm/r) 0.03 - 0.3 0.5 - 1 0.03 - 0.3 0.03 - 0.3 0.03 - 0.3 0.05 - 0.5
Once you would like to order our CBN inserts, kindly refer to email [email protected]