· Web viewWith substrate wetting agents and anti-foaming additives included in this formulation,...

SECTION 03 35 00CONCRETE FINISHES

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2015 - 2015 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Decorative concrete finishes including the following:1.1.1.1 Stains.1.1.1.2 Dyes.1.1.1.3 Dry mixes1.1.1.4 Sealers1.1.1.5 Coatings.1.1.1.6 Strippers and cleaners.1.1.1.7 Maintenance waxes.1.1.1.8 Accessory products.1.1.1.9 Countertop mixes.1.1.1.10 Polishing compounds.

1.2 RELATED SECTIONS

1.2.1 Section 03 30 00 - Cast-in-Place Concrete.

1.3 REFERENCES

1.3.1 AASHTO Specification M-148: Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete.

1.3.2 ASTM International (ASTM):1.3.2.1 ASTM C 309: Standard Specification for Liquid Membrane-Forming Compounds

for Curing Concrete.1.3.2.2 ASTM C-156: Standard Test Method for Water Loss [from a Mortar Specimen]

Through Liquid Membrane-Forming Curing Compounds for Concrete.1.3.2.3 ASTM C 1315: Standard Specification for Liquid Membrane-Forming

Compounds Having Special Properties for Curing and Sealing Concrete.1.3.2.4 ASTM D-124: Standard Specification for Degummed Soybean Oil.1.3.2.5 ASTM D-412: Test Methods for Vulcanized Rubber and Thermoplastic Rubbers

and Thermoplastic Elastomers-Tension.1.3.2.6 ASTM D-638: Standard Test Method for Tensile Properties of Plastics.1.3.2.7 ASTM D-882: Standard Test Method for Tensile Properties of Thin Plastic

Sheeting.

03 35 00-1

1.3.2.8 ASTM D-2240: Standard Test Method for Rubber PropertyDurometer Hardness.1.3.2.9 ASTM D-2471: Test Method for Gel Time and Peak Exothermic Temperature of

Reacting Thermosetting Resins.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.4.2.1 Preparation instructions and recommendations.1.4.2.2 Storage and handling requirements and recommendations.1.4.2.3 Installation methods.

1.4.3 Shop Drawings:

1.4.4 Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

1.4.5 Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, color, and patterns.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.

1.5.2 Installer Qualifications: Minimum 2 year experience installing similar products.

1.5.3 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1.5.3.1 Finish areas designated by Architect.1.5.3.2 Do not proceed with remaining work until workmanship is approved by Architect.1.5.3.3 Refinish mock-up area as required to produce acceptable work.

1.6 PRE-INSTALLATION MEETINGS

1.6.1 Convene minimum two weeks prior to starting work of this section.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Deliver and store products in manufacturer's unopened packaging bearing the brand name and manufacturer's identification until ready for installation.

1.7.2 Handling: Handle materials to avoid damage.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.9 SEQUENCING

1.9.1 Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

2 PRODUCTS

2.1 MANUFACTURERS

03 35 00-2

2.1.1 Acceptable Manufacturer: SS Specialties, which is located at: 121 N. E. 40th St.; Oklahoma City, OK 73105; Toll Free Tel: 405-525-2426; Fax: 405-525-3367; Email:request info (); Web:www.ssspecialtiesconcrete.com

2.1.2 Email: [email protected]. Web: http://www.ssspecialtiesconcrete.com.

2.1.3 Substitutions: Not permitted.

2.1.4 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 DECORATIVE CONCRETE FlNlSHES

2.2.1 Products and system components shall be VOC compliant with state and federal regulations required for the Project.

2.2.2 Decorative Concrete Finish System: Provide materials and products as manufactured by SS Specialties in combination and sequence to replicate the Project Mock-Up in design, finish and performance.

2.3 COLORS

2.3.1 Product: Sedona Acid Stain.2.3.1.1 Type: Concentrated penetrating reactive stain.2.3.1.2 Finish: Aged antique appearance.2.3.1.3 Color: Malay Tan.2.3.1.4 Color: Black.2.3.1.5 Color: English Red.2.3.1.6 Color: Green Lawn.2.3.1.7 Color: Cola.2.3.1.8 Color: Aqua Blue.2.3.1.9 Color: Golden Wheat.2.3.1.10 Color: Vintage Umber.2.3.1.11 Color: Walnut.2.3.1.12 Color: Fern.

2.3.2 Product: DYE-namic Acetone Dye.2.3.2.1 Application: Interior.

2.3.2.1.1 Solids: N/A.2.3.2.1.2 Drying Time: Approximately 5 minutes.2.3.2.1.3 Application Temperature: 40 degrees F to 85 degrees F (2.3.2.1.4 Wet Appearance: Colored Liquid.2.3.2.1.5 Dry Appearance: Colored Powder.2.3.2.1.6 VOC Content: 0 g/l.2.3.2.1.7 Blush Resistance: N/A.2.3.2.1.8 Solvent Resistance: N/A.2.3.2.1.9 Concrete Adhesion: Excellent.

2.3.2.2 Application Formula: Exterior UV Resistant.2.3.2.2.1 Solids: < 10%.2.3.2.2.2 Drying Time: > 1 minutes.2.3.2.2.3 Application Temperature: 40 degrees F to 85 degrees F (2.3.2.2.4 Wet Appearance: Colored Liquid.2.3.2.2.5 Dry Appearance: Colored Powder.2.3.2.2.6 VOC Content: < 50 g/l.2.3.2.2.7 Blush Resistance: N/A.2.3.2.2.8 Solvent Resistance: N/A.2.3.2.2.9 Concrete Adhesion: Excellent.

03 35 00-3

2.3.2.3 Primary Color: Yellow.2.3.2.4 Primary Color: Glacier Blue.2.3.2.5 Primary Color: Dixie Red.2.3.2.6 Color: Black.2.3.2.7 Color: Burnt Sienna.2.3.2.8 Color: Caramel.2.3.2.9 Color: Chestnut.2.3.2.10 Color: Chocolate.2.3.2.11 Color: Dixie Red.2.3.2.12 Color: Eggplant.2.3.2.13 Color: Forest Green.2.3.2.14 Color: Glacier.2.3.2.15 Color: Gold.2.3.2.16 Color: Green.2.3.2.17 Color: Mahogany.2.3.2.18 Color: Midnight Black.2.3.2.19 Color: Raw Sienna.2.3.2.20 Color: Saddle Brown.2.3.2.21 Color: Sand.2.3.2.22 Color: Slate Blue.2.3.2.23 Color: Terra Cotta.2.3.2.24 Color: Turquoise.2.3.2.25 Color: Walnut.2.3.2.26 Color: Yellow.

2.3.3 Product: Rainbow Water-Borne Stains.2.3.3.1 Solids: 15-18% by weight and 13-16% by volume.2.3.3.2 Finish: Top coat with SS Sealers for maximum durability.2.3.3.3 Coverage: 240 sq. ft. per gallon at 1 mil dry film thickness.2.3.3.4 Drying Time (to touch): 2 hours at 77 degrees F.2.3.3.5 Drying Time (re-coat): 4 hours at 77 degrees F.2.3.3.6 Application Temperature: Above 40 degrees F.2.3.3.7 Clean up: Warm, soapy water.2.3.3.8 Color: Aqua Blue.2.3.3.9 Color: Acid Black.2.3.3.10 Color: Almondine.2.3.3.11 Color: Blue Iris.2.3.3.12 Color: Cha-Cha.2.3.3.13 Color: Coral Gray.2.3.3.14 Color: Chocolate.2.3.3.15 Color: Cola.2.3.3.16 Color: Dawn Cloud.2.3.3.17 Color: Dusty Mauve.2.3.3.18 Color: English Red.2.3.3.19 Color: Fern.2.3.3.20 Color: Glacier Blue.2.3.3.21 Color: Green Lawn.2.3.3.22 Color: Golden Wheat.2.3.3.23 Color: Irish Luck.2.3.3.24 Color: Jet Black.2.3.3.25 Color: Malay Tan.2.3.3.26 Color: Natural Beige.2.3.3.27 Color: Olive.2.3.3.28 Color: Pale Avocado.2.3.3.29 Color: Pamona.2.3.3.30 Color: Royal Velvet.

03 35 00-4

2.3.3.31 Color: Shasta Daisy.2.3.3.32 Color: Salt Lake.2.3.3.33 Color: Sparrow.2.3.3.34 Color: Sandstone.2.3.3.35 Color: Texas Sand.2.3.3.36 Color: Vintage Umber.2.3.3.37 Color: White.2.3.3.38 Color: Walnut.

2.3.4 Product: Vertical Concrete Color.2.3.4.1 Solids: 55.38+/-2.0%.2.3.4.2 Solids by Volume: 43.75+/-2.0%.2.3.4.3 Theoretical Coverage: 702(sf/gal at 1 mil dry film).2.3.4.4 Drying time (to touch): 35-40 minutes at 77 degrees F.2.3.4.5 Drying time (recoat): 2-4 hours at 77 degrees F.2.3.4.6 Application Temperature: above 40 degrees F below 90 degrees F.2.3.4.7 Clean up: Soap and Water.2.3.4.8 Color: Beige Natural Color.2.3.4.9 Color: Black Natural Color.2.3.4.10 Color: Dark Brown Natural Color.2.3.4.11 Color: Dark Gray Natural Color.2.3.4.12 Color: Medium Gray Natural Color.2.3.4.13 Color: Light Gray Natural Color.2.3.4.14 Color: Off White Natural Color.2.3.4.15 Color: Light Reddish Brown Natural Color.2.3.4.16 Color: Blue Detail Color.2.3.4.17 Color: Green Detail Color.2.3.4.18 Color: Red Detail Color.2.3.4.19 Color: Yellow Detail Color.

2.3.5 Product: Supreme Color Pac.2.3.5.1 Solids (Diluted): Depends on sealer used.2.3.5.2 Drying Time: 1 to 2 hours.2.3.5.3 Recoat Time: 4 to 24 hours.2.3.5.4 Foot Traffic: 4 to 6 hours.2.3.5.5 Wheel Traffic: 24 to 48 hours.2.3.5.6 Application Temp: 40 degrees F to 85 degrees F.2.3.5.7 Wet Appearance: Varies depending upon color.2.3.5.8 Dry Appearance: Varies, High Gloss.2.3.5.9 VOC Content: N/A.2.3.5.10 Blush Resistance: Good.2.3.5.11 Solvent Resistance: Minimal.2.3.5.12 Concrete Adhesion: Excellent.2.3.5.13 Color: Arabian Sand.2.3.5.14 Color: Brick Red.2.3.5.15 Color: Buff.2.3.5.16 Color: Canyon Clay.2.3.5.17 Color: Charcoal.2.3.5.18 Color: Dark Gray.2.3.5.19 Color: Medium Gray.2.3.5.20 Color: Light Gray.2.3.5.21 Color: Off White.2.3.5.22 Color: Sun Buff.2.3.5.23 Color: Taupe.2.3.5.24 Color: Tile Red.

03 35 00-5

2.3.6 Product: Metallic.2.3.6.1 Solids (Diluted): N/A.2.3.6.2 Drying Time: Refer to Epoxy Technical Data.2.3.6.3 Recoat Time: Refer to Epoxy Technical Data.2.3.6.4 Foot Traffic: Refer to Epoxy Technical Data.2.3.6.5 Wheel Traffic: Refer to Epoxy Technical Data.2.3.6.6 Application Temp: Refer to Epoxy Technical Data.2.3.6.7 Wet Appearance: Colored liquid.2.3.6.8 Dry Appearance: Colored powder.2.3.6.9 VOC Content: N/A.2.3.6.10 Blush Resistance: N/A.2.3.6.11 Solvent Resistance: N/A.2.3.6.12 Concrete Adhesion: N/A.2.3.6.13 Color: Burnt Orange Metallic.2.3.6.14 Color: Midnight Blue Metallic.2.3.6.15 Color: Bark Brown Metallic.2.3.6.16 Color: Charcoal Metallic.2.3.6.17 Color: Pearl Metallic.2.3.6.18 Color: Walnut Metallic.2.3.6.19 Color: Purple Metallic.2.3.6.20 Color: Golden Brown Metallic.2.3.6.21 Color: Green Metallic.2.3.6.22 Color: Royal Blue Metallic.2.3.6.23 Color: Moss Green Metallic.2.3.6.24 Color: Chocolate Metallic.2.3.6.25 Color: Khaki Metallic.2.3.6.26 Color: Copper Metallic.2.3.6.27 Color: Black Metallic.2.3.6.28 Color: Silver Metallic.2.3.6.29 Color: Dark Cherry Metallic.2.3.6.30 Color: Tangerine Metallic.2.3.6.31 Color: Forest Green Metallic2.3.6.32 Color: Espresso.

2.3.7 Product: Color Dispersion.2.3.7.1 Solids (Diluted): Depends on Polyaspartic used.2.3.7.2 Drying Time: Refer to Polyaspartic Technical Data.2.3.7.3 Recoat Time: Refer to Polyaspartic Technical Data.2.3.7.4 Foot Traffic: Refer to Polyaspartic Technical Data.2.3.7.5 Wheel Traffic: Refer to Polyaspartic Technical Data.2.3.7.6 Application Temp: 40 degrees F to 85 degrees F.2.3.7.7 Wet Appearance: Depends on Polyaspartic color used.2.3.7.8 Dry Appearance: Varies, high gloss.2.3.7.9 VOC Content: Depends on Polyaspartic used.2.3.7.10 Blush Resistance: Excellent.2.3.7.11 Solvent Resistance: Excellent.2.3.7.12 Concrete Adhesion: Excellent.2.3.7.13 Color: Black.2.3.7.14 Color: Caramel.2.3.7.15 Color: Dolphin Gray.2.3.7.16 Color: Mint Green.2.3.7.17 Color: Mocha.2.3.7.18 Color: Royal Blue.2.3.7.19 Color: Sandy Beige.2.3.7.20 Color: Sky Blue.2.3.7.21 Color: Stone Gray.

03 35 00-6

2.3.7.22 Color: Safety Red.2.3.7.23 Color: Safety Yellow.2.3.7.24 Color: Terra Cotta.2.3.7.25 Color: White.2.3.7.26 Color: White Night Gray.

2.4 DRY MIXES

2.4.1 Product: Spray/Base Mix.2.4.1.1 Appearance: White Liquid.2.4.1.2 Nonvolatile Content, %: 47(-) 0.5.2.4.1.3 Ph: 10.5 to 11.5.2.4.1.4 Solids, %: 48%.2.4.1.5 Bulk Density: 8.2 lb/gallon.2.4.1.6 Freeze Point: 32 degrees F.2.4.1.7 Glass Transition Temperature: +/-12 degrees C.2.4.1.8 Color: Gray.2.4.1.9 Color: White.

2.4.2 Product: Stamp Mix.2.4.2.1 Appearance: White Liquid.2.4.2.2 Nonvolatile Content, %: 47(-) 0.5.2.4.2.3 Ph: 10.5 to 11.5.2.4.2.4 Solids, %: 48%.2.4.2.5 Bulk Density: 8.2 lb/gallon.2.4.2.6 Freeze Point: 32 degrees F.2.4.2.7 Glass Transition Temperature: +/-12 degrees C.2.4.2.8 Color: Gray.2.4.2.9 Color: White.

2.4.3 Product: SLICK'EM.2.4.3.1 Finish: Must be top coated with a solvent or water base sealer.2.4.3.2 Coverage: 1500/2500 sq. ft depending on surface profile.2.4.3.3 Drying Time (re-coat): 4 hours at 72 degrees F (Drying time is affected by the

thickness of application, humidity, and circulation etc.)2.4.3.4 Drying Time (staining): Overnight.2.4.3.5 Clean up: Warm, soapy water.

2.4.4 Product: Concentrated Liquid Polymer Resin.2.4.4.1 Appearance: White Liquid.2.4.4.2 Solids Content, %: 48%.2.4.4.3 Nonvolatile Content, %: 47(-) 0.5.2.4.4.4 Ph: 10.5 to 11.5.2.4.4.5 Bulk Density: 8.2 lb/gallon.2.4.4.6 Freeze Point: 32 degrees F.2.4.4.7 Application Temperature: Above 45 degrees F.2.4.4.8 Glass Transition Temperature: +/-12 degrees C.

2.5 SEALERS

2.5.1 Product: Deco Guard.2.5.1.1 Type: Siloxane Modified Methyl Methacrylate Sealer- Low Sheen.2.5.1.2 Solids: 15+ or - 1%.2.5.1.3 Drying Time*: 30 minutes to 1 hour.2.5.1.4 Re-Coat Time: 4 to 24 hours.2.5.1.5 Foot Traffic: 4 to 6 hours.2.5.1.6 Wheel Traffic: 24 to 48 hours.

03 35 00-7

2.5.1.7 Application Temperature: 50 degrees F to 80 degrees F.2.5.1.8 Wet Appearance: Clear to slightly hazy.2.5.1.9 Dry Appearance: Clear and low gloss.2.5.1.10 VOC Content: < 350 g/l.2.5.1.11 Blush Resistance: Good.2.5.1.12 Solvent Resistance: Minimal.2.5.1.13 Concrete Adhesion: Excellent.2.5.1.14 Standards Compliance:

2.5.1.14.1 ASTM C 309, Type 1, Class A & B.2.5.1.14.2 AASHTO Specification M-148, Type 1, Class A & B.

2.5.2 Product: Deco Guard Plus.2.5.2.1 Type: Siloxane Modified Methyl Methacrylate Sealer-High Gloss.2.5.2.2 Solids: 25+ or - 1%.2.5.2.3 Drying Time*: 30 minutes to 1 hour.2.5.2.4 Re-Coat Time: 4 to 24 hours.2.5.2.5 Foot Traffic: 4 to 6 hours.2.5.2.6 Wheel Traffic: 24 to 48 hours.2.5.2.7 Application Temperature: 50 degrees F to 80 degrees F.2.5.2.8 Wet Appearance: Clear to slightly hazy.2.5.2.9 Dry Appearance: Clear and high gloss.2.5.2.10 VOC Content: < 350 g/l.2.5.2.11 Blush Resistance: Good.2.5.2.12 Solvent Resistance: Minimal.2.5.2.13 Concrete Adhesion: Excellent.2.5.2.14 Standards Compliance:

2.5.2.14.1 ASTM C 1315, Type 1, Class A & B.

2.5.3 Product: EpoSeal 20.2.5.3.1 Type: Non-Yellowing, Penetrating Epoxy/Acrylic Interior Concrete Sealer.2.5.3.2 Solids: 20%.2.5.3.3 Drying Time*: 1 to 4 hours.2.5.3.4 Re-Coat Time: 4 to 24 hours.2.5.3.5 Foot Traffic: 4 to 6 hours.2.5.3.6 Wheel Traffic: 24 to 48 hours.2.5.3.7 Application Temperature: 50 degrees F to 85 degrees F.2.5.3.8 Wet Appearance: Milky white.2.5.3.9 Dry Appearance: Clear and satin finish.2.5.3.10 VOC Content: < 93 g/l.2.5.3.11 Blush Resistance: Good.2.5.3.12 Solvent Resistance: Superior.2.5.3.13 Concrete Adhesion: Excellent.2.5.3.14 Standards Compliance:

2.5.3.14.1 Dried film is USDA approved. ASTM C-1315, ASTM C-309, and ASTM C-156.

2.5.4 Product: EpoSeal 38.2.5.4.1 Type: Non-Yellowing, High Gloss Epoxy/Acrylic Interior Concrete Sealer.2.5.4.2 Solids: 38%.2.5.4.3 Drying Time*: 1 to 2 hours.2.5.4.4 Re-Coat Time: 4 to 24 hours.2.5.4.5 Foot Traffic: 4 to 6 hours.2.5.4.6 Wheel Traffic: 24 to 48 hours.2.5.4.7 Application Temperature: 50 degrees F to 85 degrees F.2.5.4.8 Wet Appearance: Milky white.2.5.4.9 Dry Appearance: Clear and satin finish.

03 35 00-8

2.5.4.10 VOC Content: < 100 g/l.2.5.4.11 Blush Resistance: Good.2.5.4.12 Solvent Resistance: Superior.2.5.4.13 Concrete Adhesion: Excellent.2.5.4.14 Standards Compliance:

2.5.4.14.1 Dried film is USDA approved. ASTM C-1315, ASTM C-309, and ASTM C-156.

2.5.5 Product: Supreme 2500 Medium Gloss.2.5.5.1 Type: 100% Pure Acrylic Non-Yellowing, Penetrating Sealer.2.5.5.2 Solids: 25%.2.5.5.3 Drying Time*: 1 to 2 hours.2.5.5.4 Re-Coat Time: 4 to 24 hours.2.5.5.5 Foot Traffic: 4 to 6 hours.2.5.5.6 Wheel Traffic: 24 to 48 hours.2.5.5.7 Application Temperature: 40 degrees F to 85 degrees F.2.5.5.8 Wet Appearance: Clear to lightly cloudy.2.5.5.9 Dry Appearance: Clear and medium gloss.2.5.5.10 VOC Content: < 700 g/l.2.5.5.11 Blush Resistance: Good.2.5.5.12 Solvent Resistance: minimal.2.5.5.13 Concrete Adhesion: Excellent.2.5.5.14 Standards Compliance:

2.5.5.14.1 Dried film is USDA accepted.2.5.5.14.2 ASTM C-1315, Type 1 Class A.2.5.5.14.3 ASTM C-309, Type 1 Class A and B.

2.5.6 Product: Supreme 2500 High Gloss.2.5.6.1 Type: 100% Pure Acrylic Non-Yellowing, High Gloss Sealer.2.5.6.2 Solids: 25%.2.5.6.3 Drying Time*: 1 to 2 hours.2.5.6.4 Re-Coat Time: 4 to 24 hours.2.5.6.5 Foot Traffic: 4 to 6 hours.2.5.6.6 Wheel Traffic: 24 to 48 hours.2.5.6.7 Application Temperature: 40 degrees F to 85 degrees F.2.5.6.8 Wet Appearance: Clear to lightly cloudy.2.5.6.9 Dry Appearance: Clear and high gloss.2.5.6.10 VOC Content: < 700 g/l.2.5.6.11 Blush Resistance: Good.2.5.6.12 Solvent Resistance: minimal.2.5.6.13 Concrete Adhesion: Excellent.2.5.6.14 Standards Compliance:

2.5.6.14.1 Dried film is USDA accepted.

2.5.7 Product: Supreme 2500 PLUS Medium Gloss.2.5.7.1 Type: Medium Gloss, UV Resistant 25% Acrylic Copolymer Concrete Sealer.2.5.7.2 Solids: 25%.2.5.7.3 Drying Time*: 1 to 2 hours.2.5.7.4 Re-Coat Time: 4 to 24 hours.2.5.7.5 Foot Traffic: 4 to 6 hours.2.5.7.6 Wheel Traffic: 24 to 48 hours.2.5.7.7 Application Temperature: 40 degrees F to 85 degrees F.2.5.7.8 Wet Appearance: Clear to lightly cloudy.2.5.7.9 Dry Appearance: Clear and medium gloss.2.5.7.10 VOC Content: < 700 g/l.2.5.7.11 Blush Resistance: Good.

03 35 00-9

2.5.7.12 Solvent Resistance: minimal.2.5.7.13 Concrete Adhesion: Excellent.2.5.7.14 Standards Compliance:

2.5.7.14.1 Dried film is USDA accepted.2.5.7.14.2 ASTM C-1315, Type 1 Class A.2.5.7.14.3 ASTM C-309, Type 1 Class A and B.2.5.7.14.4 AASHTO Specification M-148, Type 1, Class A & B.2.5.7.14.5 Dried coating is USDA accepted.

2.5.8 Product: Supreme 3000 High Gloss.2.5.8.1 Type: 100% Pure Acrylic Non-Yellowing, High Gloss Sealer.2.5.8.2 Solids: 30%.2.5.8.3 Drying Time*: 1 to 2 hours.2.5.8.4 Re-Coat Time: 4 to 24 hours.2.5.8.5 Foot Traffic: 4 to 6 hours.2.5.8.6 Wheel Traffic: 24 to 48 hours.2.5.8.7 Application Temperature: 40 degrees F to 85 degrees F.2.5.8.8 Wet Appearance: Clear to lightly cloudy.2.5.8.9 Dry Appearance: Clear and high gloss.2.5.8.10 VOC Content: < 700 g/l.2.5.8.11 Blush Resistance: Good.2.5.8.12 Solvent Resistance: minimal.2.5.8.13 Concrete Adhesion: Excellent.2.5.8.14 Standards Compliance:

2.5.8.14.1 Dried film is USDA accepted.

2.6 COATINGS

2.6.1 Product: Water Based 40 Epoxy.2.6.1.1 Type: Low Odor, Two Component, Water Based Epoxy.2.6.1.2 Abrasion resistance: 54 to 65 mg loss.2.6.1.3 (Taber index, ASTM 4060-81, CS-17 abrasion Wheel, 1000 gram load).2.6.1.4 Gloss 60: 86.2.6.1.5 Flexibility (1/8 inch mandrel): Pass.2.6.1.6 Hardness (7 days): Fail.2.6.1.7 Water Resistance: Excellent.2.6.1.8 Solids % Weight (Federal Spec. TTP-141B): 40%.2.6.1.9 Density lbs/gal. (Federal Spec. TTP-141B): 8.54.2.6.1.10 VOC: < 20 grams/liter.2.6.1.11 Mix ratio (a/b volume): 1 to 1.2.6.1.12 Coverage (3 to 5 mils DFT): 250- 340 sq. ft./gal.2.6.1.13 Viscosity: 200 to 350 cps.2.6.1.14 Pot Life: 1 to 1.5 hours.2.6.1.15 Dry Time- Set to Touch (50% R.H. at 72 degrees F): 20 to 40 minutes.2.6.1.16 Dry Time- Recoat (50% R.H. at 72 degrees F): 4 to 6 hours.2.6.1.17 Dry Time- Light Traffic (50% R.H. at 72 degrees F): 6 to 12 hours.2.6.1.18 Dry Time- Full Cure (50% R.H. at 72 degrees F): 2 to 5 days.2.6.1.19 Application Temperature: 50 to 90 degrees F with RH below 75%.2.6.1.20 Chemical & Stain Resistance (chemical spot resistance with 1 hour and 18 hour

exposure, 1 h/18 h):2.6.1.20.1 Toluene: No Change/No Change.2.6.1.20.2 Ethanol: No Change/No Change.2.6.1.20.3 Sulfuric Acid (10%): No Change/No Change.2.6.1.20.4 Acetic Acid (3%): No Change/No Change.2.6.1.20.5 Acetic Acid (10%): Haze + Blister/ Blister.2.6.1.20.6 Coffee: No Change.

03 35 00-10

2.6.1.20.7 Ketchup: No Change.2.6.1.20.8 Mustard: No Change.2.6.1.20.9 Red Wine: Slight Stain.

2.6.2 Product: Water Based 55 Epoxy.2.6.2.1 Type: Low Odor, Two Component, Water Based Epoxy.2.6.2.2 Abrasion resistance: 45 to 55 mg loss.2.6.2.3 (Taber index, ASTM 4060-81, CS-17 abrasion Wheel, 1000 gram load).2.6.2.4 Gloss 60: 90.2.6.2.5 Flexibility (1/8 inch mandrel): Pass.2.6.2.6 Hardness (7 days): Fail.2.6.2.7 Water Resistance: Excellent.2.6.2.8 Solids % Weight (Federal Spec. TTP-141B): 55%.2.6.2.9 Density lbs/gal. (Federal Spec. TTP-141B): 8.96.2.6.2.10 VOC: < 20 grams/liter.2.6.2.11 Mix ratio (a/b volume): 1 to 1.2.6.2.12 Coverage (3 to 5 mils DFT): 250- 330 sq. ft./gal.2.6.2.13 Viscosity: 200 to 500 cps.2.6.2.14 Pot Life: 1 to 1.5 hours.2.6.2.15 Dry Time- Set to Touch (50% R.H. at 72 degrees F): 20 to 40 minutes.2.6.2.16 Dry Time- Recoat (50% R.H. at 72 degrees F): 4 to 6 hours.2.6.2.17 Dry Time- Light Traffic (50% R.H. at 72 degrees F): 6 to 12 hours.2.6.2.18 Dry Time- Full Cure (50% R.H. at 72 degrees F): 2 to 5 days.2.6.2.19 Application Temperature: 55 to 90 degrees F with RH below 75%.2.6.2.20 Chemical & Stain Resistance (chemical spot resistance with 1 hour and 18 hour

exposure, 1 h/18 h):2.6.2.20.1 Toluene: No Change/No Change.2.6.2.20.2 Ethanol: No Change/No Change.2.6.2.20.3 Sulfuric Acid (10%): No Change/No Change.2.6.2.20.4 Acetic Acid (3%): No Change/No Change.2.6.2.20.5 Acetic Acid (10%): Haze + Blister/ Blister.2.6.2.20.6 Coffee: No Change.2.6.2.20.7 Ketchup: No Change.2.6.2.20.8 Mustard: No Change.2.6.2.20.9 Red Wine: Slight Stain.

2.6.3 Product: Water Based 60 Urethane.2.6.3.1 Type: High Solids, Low VOC Two Part Water Based Aliphatic Polyurethane.2.6.3.2 Abrasion Resistance: 38-40 mg loss.2.6.3.3 (Taber Index, ASTM 4060-81, CS-17 Abrasion Wheel, 1000 gram load).2.6.3.4 Gloss 60 degrees (Gloss): 88.2.6.3.5 Gloss 60 degrees (Matte): Matte.2.6.3.6 Flexibility (1/8 inch Mandrel): Pass.2.6.3.7 Pendulum Hardness, sec. (ASTM D-4336): 175.2.6.3.8 Water Resistance: Excellent.2.6.3.9 Solids % Weight (Federal Spec. TTP-141B): 53%.2.6.3.10 Density lbs/gal. (Federal Spec. TTP-141B): 8.83.2.6.3.11 VOC: 100 grams per liter.2.6.3.12 Mix Ratio (a/b volume): 2 to 1.2.6.3.13 Coverage (2-4 mils dft.): 300-400 sq. ft./gal.2.6.3.14 Pot Life (higher temperatures shorten pot life): 30-45 minutes.2.6.3.15 Dry TimeSet to Touch (50% R.H. at 72 degrees F): 5-6 hours.2.6.3.16 Dry TimeRecoat (50% R.H. at 72 degrees F): 12 hours.2.6.3.17 Dry TimeLight Traffic (50% R.H. at 72 degrees F): 18 hours.2.6.3.18 Dry TimeFull Cure (heavy traffic) (50% R.H. at 72 degrees F): 7 days.2.6.3.19 Application temperature: 55-90 degrees F with relative humidity below 75%.

03 35 00-11

2.6.3.20 Chemical Resistance:2.6.3.20.1 Urine: No Effect.2.6.3.20.2 Blood: No Effect.2.6.3.20.3 Brake Fluid: No Effect.2.6.3.20.4 Xylene: No Effect.2.6.3.20.5 Gasoline: No Effect.2.6.3.20.6 Skydrol B-4: No Effect.2.6.3.20.7 Ethylene Glycol: No Effect.2.6.3.20.8 MEK: Film Softened.2.6.3.20.9 10% Sodium Hydroxide: No Effect.2.6.3.20.10 50% Sodium Hydroxide: No Effect.2.6.3.20.11 25% Sulfuric Acid: No Effect.2.6.3.20.12 25% Acetic Acid: No Effect.2.6.3.20.13 20% Nitric Acid: No Effect.2.6.3.20.14 10% Hydrochloric Acid: No Effect.2.6.3.20.15 ** A chemical exposure test shall be performed prior to application to

ensure satisfactory resistance.

2.6.4 Product: Poly Pro 38.2.6.4.1 Type: Two-Component, Low Viscosity Acrylic Urethane.2.6.4.2 Abrasion Resistance: 65 to 70 mg loss.2.6.4.3 (Taber Index, ASTM 4060-81, CS-17 Abrasion Wheel, 1000 gram load).2.6.4.4 Gloss 60 degrees (G): 92.2.6.4.5 Elongation (ASTM D882-67): 5.1 to 7.1 %.2.6.4.6 Flexibility (1/8 inch Mandrel): Pass.2.6.4.7 Hardness (7 days): 5H to 6H.2.6.4.8 Heat Resistance: 300 degrees F.2.6.4.9 Water Resistance: Excellent.2.6.4.10 Solids % Weight (Federal Spec. TTP-141B): 51%.2.6.4.11 Density lbs/gal. (Federal Spec. TTP-141B): 8.51.2.6.4.12 VOC: 400 grams per liter.2.6.4.13 Mix Ratio (a/b volume): 4 to 1.2.6.4.14 Coverage (3 mils dft.): 280 sq. ft./gal.2.6.4.15 Viscosity: 85 to 87 KU.2.6.4.16 Pot Life: 45 minutes.2.6.4.17 Dry TimeSet to Touch (50% R.H. at 72 degrees F): 2 hours.2.6.4.18 Dry TimeRecoat (50% R.H. at 72 degrees F): 10 to 12 hours.2.6.4.19 Dry TimeLight Traffic (50% R.H. at 72 degrees F): 24 hours.2.6.4.20 Dry TimeCure (50% R.H. at 72 degrees F): 72 hours.2.6.4.21 Dry TimeFull Cure (50% R.H. at 72 degrees F): 7 days.2.6.4.22 Solvent: Xylene, Butyl Acetate, Aromatic 100.2.6.4.23 Flash Point: 80 degrees F.2.6.4.24 Chemical Resistance:

2.6.4.24.1 Wine: No Effect.2.6.4.24.2 Urine: No Effect.2.6.4.24.3 Gasoline: No Effect.2.6.4.24.4 Motor Oil: No Effect.2.6.4.24.5 Brake Fluid: No Effect.2.6.4.24.6 Transmission Fluid: No Effect.2.6.4.24.7 Skydrol: No Effect.2.6.4.24.8 10% Sulfuric Acid: No Effect.2.6.4.24.9 10% Hydrochloric Acid: No Effect.2.6.4.24.10 10% Acetic Acid: No Effect.2.6.4.24.11 Xylene: No Effect.2.6.4.24.12 MEK: No Effect.

03 35 00-12

2.6.5 Product: Aliphatic 100% Epoxy.2.6.5.1 Type: Two Component Cyclo-Aliphatic Amine Epoxy Coating for Concrete.2.6.5.2 Abrasion Resistance: 28.1 mg loss.2.6.5.3 (Taber Index, ASTM 4060-81, CS-17 Abrasion Wheel, 1000 gram load).2.6.5.4 Gloss 60 degrees: 90 to 95.2.6.5.5 Flexibility (1/8 inch Mandrel): Pass.2.6.5.6 Hardness (Shore D): 82.2.6.5.7 Compressive Strength at Yield (psi): 11,200.2.6.5.8 Tensile Strength (ASTM D-638): 6200.2.6.5.9 Elongation: 7 %.2.6.5.10 Solids % Weight (Federal Spec. TTP-141B): 100%.2.6.5.11 Density lbs/gal. (Federal Spec. TTP-141B): 9.32.2.6.5.12 VOC: < 5 grams per liter.2.6.5.13 Mix Ratio (a/b volume): 2 to 1. 19.33 # part A (2.0 gallon approximately) to 8.66

# part B (1 gallon approximately).2.6.5.14 Viscosity: 400 to 600 cps.2.6.5.15 Pot Life: 20 to 30 minutes.2.6.5.16 Dry TimeSet to Touch (50% R.H. at 72 degrees F): 6 to 8 hours.2.6.5.17 Dry TimeRecoat (50% R.H. at 72 degrees F): 10 to 16 hours.2.6.5.18 Dry TimeLight Traffic (50% R.H. at 72 degrees F): 14 to 18 hours.2.6.5.19 Dry TimeFull Cure (Heavy Traffic) (50% R.H. at 72 degrees F): 2 to 7 days.2.6.5.20 Application Temperature: 55 to 90 degrees F.2.6.5.21 Chemical Resistance: Rating Key: Anot recommended, B2 hour term splash

spill, C8 hour term splash spill, D72 hour immersion, Elong term immersion.2.6.5.21.1 Butanol: C.2.6.5.21.2 10% Sulfuric Acid: C.2.6.5.21.3 MEK: A.2.6.5.21.4 Gasoline: C.2.6.5.21.5 Xylene: C.2.6.5.21.6 70% Sulfuric Acid: A.2.6.5.21.7 10% Sodium Hydroxide: E.2.6.5.21.8 Skydrol B-4: B.2.6.5.21.9 1,1,1 Trichloroethane: B.2.6.5.21.10 5% Acetic Acid: B.2.6.5.21.11 10% Hydrochloric Acid: No Effect.2.6.5.21.12 50% Sodium Hydroxide: D.2.6.5.21.13 Ethylene Alcohol: C.2.6.5.21.14 Methanol: A.2.6.5.21.15 10% HCI (ag): C.

2.6.6 Product: Aliphatic 60% Urethane.2.6.6.1 Type: Two Component, Aliphatic Polyurethane Coating for Concrete.2.6.6.2 Abrasion Resistance: 35 mg loss.2.6.6.3 (Taber Index, ASTM 4060-81, CS-17 Abrasion Wheel, 1000 gram load).2.6.6.4 Gloss 60 degrees: 90 to 95.2.6.6.5 Hardness (Shore D): 62.2.6.6.6 Water Resistance: Excellent.2.6.6.7 Solids % Weight (Federal Spec. TTP-141B): 60%.2.6.6.8 Density lbs/gal. (Federal Spec. TTP-141B): 8.49.2.6.6.9 VOC: < 400 grams per liter.2.6.6.10 Mix Ratio (a/b volume): 2 to 1.2.6.6.11 Viscosity: 400 to 600 cps.2.6.6.12 Pot Life: 1 to 1.5 hours.2.6.6.13 Dry TimeSet to Touch (50% R.H. at 72 degrees F): 4 to 6 hours.2.6.6.14 Dry TimeRecoat (50% R.H. at 72 degrees F): 10 to 12 hours.2.6.6.15 Dry TimeLight Traffic (50% R.H. at 72 degrees F): 24 hours.

03 35 00-13

2.6.6.16 Dry TimeFull Cure (Heavy Traffic) (50% R.H. at 72 degrees F): 3 to 5 days.2.6.6.17 Chemical Resistance:

2.6.6.17.1 Urine: No Effect.2.6.6.17.2 25% Sulfuric Acid: No Effect.2.6.6.17.3 MEK: No Effect.2.6.6.17.4 Gasoline: No Effect.2.6.6.17.5 Blood: No Effect.2.6.6.17.6 25% Acetic Acid: No Effect.2.6.6.17.7 10% Sodium Hydroxide: No Effect.2.6.6.17.8 Skydrol B-4: No Effect.2.6.6.17.9 Brake Fluid: No Effect.2.6.6.17.10 20% Nitric Acid: No Effect.2.6.6.17.11 50% Sodium Hydroxide; No Effect.2.6.6.17.12 Ethylene Alcohol: No Effect.2.6.6.17.13 Xylene: No Effect.2.6.6.17.14 10% Hydrochloric Acid: No Effect.

2.6.7 Product: Polyaspartic 70%.2.6.7.1 Type: Two Component Polyaspartic Aliphatic Polyurea Utilizing Nanotechnology.2.6.7.2 Meets USDA/CFSAN, U.S. Food Code, physical facilities criteria as outlined in

6.100.11 Surface Characteristics USDA acceptable. Not intended for 21 CFR food contact.

2.6.7.3 Solids: 70%.2.6.7.4 Pot Life: 25 to 30 minutes.2.6.7.5 Re-coat Time: 2 to 3 hours.2.6.7.6 Foot Traffic: .3 to 4 hours.2.6.7.7 Wheel Traffic: 24 hours (recommended).2.6.7.8 Application Temperature: 40 to 85 degrees F.2.6.7.9 Wet Appearance: Clear.2.6.7.10 Dry Appearance: Clear and Very High Gloss.2.6.7.11 VOC Content: < 320 g/l.2.6.7.12 Blush Resistance: Excellent.2.6.7.13 Solvent Resistance; Excellent.2.6.7.14 Concrete Adhesion: Excellent.





03 35 00-14



2.7 STRIPPERS AND CLEANERS

2.7.1 Product: Acetone.2.7.1.1 Type: Raw Solvent for Cleanup, Thinning and Re-Emulsion.

2.7.2 Product: Xylene.2.7.2.1 Type: Raw Solvent for Cleanup, Thinning and Re-Emulsion.

2.7.3 Product: Surf-Prep.2.7.3.1 Acid Based Micro Etcher and Cleaner for Superior Floor Profiling.

2.7.4 Product: Strip-A-Lot.2.7.4.1 Biodegradable and Environmentally Friendly Coating Stripper.

2.8 MAINTENANCE WAXES

2.8.1 Product: Cherry Wax.2.8.1.1 Type: High Sheen Cherry Scented Water Based Acrylic Floor Wax.2.8.1.2 Solids; 21%.2.8.1.3 Drying Time: 1 to 2 hours.2.8.1.4 Re-Coat Time: 1 to 3 hours.2.8.1.5 Foot Traffic: 12 to 24 hours.2.8.1.6 Wheel Traffic: 24 to 48 hours.2.8.1.7 Application: 40 degrees F to 85 degrees F.2.8.1.8 Wet Appearance: Milky White.2.8.1.9 Dry Appearance: Crystal Clear.2.8.1.10 VOC Content: None.2.8.1.11 Blush Resistance: Excellent.2.8.1.12 Solvent Resistance: Good.2.8.1.13 Concrete Adhesion: Superior (over sealed surfaces).

2.8.2 Product: Cherry Wax Matte.2.8.2.1 Type: Matte Sheen Cherry Scented Water Based Acrylic Floor Wax.2.8.2.2 Characteristics: Refer to "Cherry Wax".

2.8.3 Product: Cherry Wax Plus.2.8.3.1 Type: high Performance Cherry Scented Water Based Acrylic Floor Wax.2.8.3.2 Characteristics: Refer to "Cherry Wax".2.8.3.3 Solids: 28 %.2.8.3.4 Recoat Time: 2 to 3 hours.

2.8.4 Product: Cherry Wax PLUS Matte.

03 35 00-15

2.8.4.1 Type: high Performance Cherry Scented Water Based Acrylic Floor Wax.2.8.4.2 Characteristics: Refer to "Cherry Wax".2.8.4.3 Solids: 28 %.2.8.4.4 Recoat Time: 2 to 3 hours.

2.9 ACCESSORlES

2.9.1 Product: Mottling Agent.2.9.1.1 Application: Used with Acetone.

2.9.2 Product: Matte-It.2.9.2.1 Application: Satin FinishAdd 1 pint per 5 gallon of 25% solids acrylic sealer.2.9.2.2 Application: Matte FinishAdd 2 pints per 5 gallon of 25% solids acrylic sealer.

2.9.3 Product: Seal-Grip.2.9.3.1 Type: Bleached Aluminum Oxide for Concrete.

2.9.4 Product: Get-A-Grip.2.9.4.1 Application: Anti-Slip Particle Additive for Concrete Sealers.

2.9.5 Product: Clear Liquid Release.2.9.5.1 Type: Bubble Gum Scented Decorative Clear Liquid Release Agent.

2.9.6 Product: LesCoat.2.9.6.1 Application: blocks the migration of acid and water borne stains and serves as

an effective sand blast resist for concrete surfaces.2.9.6.2 Appearance and Odor: Green substance with a mild paint like odor.2.9.6.3 Vapor Density: 4.90.2.9.6.4 Vapor Pressure: 2.00.2.9.6.5 Solubility in Water: Y.2.9.6.6 Boiling Point: 212 degrees F.2.9.6.7 Specific Gravity: 1.044.2.9.6.8 VOC Lbs per Gallon: 100.2.9.6.9 % Volatile/Vol: 65.856.2.9.6.10 % Non-Volatile Solids /Wgt: 41.395.2.9.6.11 % Non-Volatile Solids/Vol: 34.414.2.9.6.12 Container Size: 10 oz. caulking tube.

2.9.7 Product: Stencils.2.9.7.1 Stencils are 30 inches wide and as long as the design. If the design is wider than

30 inches, tiling will be required thus making the design to the custom size.

2.9.8 Product: Crack Fill.2.9.8.1 Solids: 60%.2.9.8.2 Tack Free (ASTM D2471): 4 to 5 minutes.2.9.8.3 Traffic Time: 10 to 15 minutes.2.9.8.4 Application Temperature: 30 degrees F to 85 degrees F.2.9.8.5 Mix Ration (a/b volume): 1:12.9.8.6 Dry Appearance: Light beige with some gloss.2.9.8.7 VOC Content: < 420 g/l (mixed).2.9.8.8 Pot Life: 2 minutes.2.9.8.9 Solvent Resistance: Excellent.2.9.8.10 Concrete Adhesion: Excellent.2.9.8.11 Hardness (ASTM D2240 Shore D): 70.2.9.8.12 Tack Free (ASTM D2471): 4 to 5 minutes.2.9.8.13 Tensile (ASTM D412): 4500, filled.2.9.8.14 Tear Strength, pli (ASTM 624-C): 560.

03 35 00-16

2.9.8.15 Elongation (ASTM D124): 3.3%.

2.9.9 Product: Color Vinyl Chips.2.9.9.1 Design: Carmel Chips on Sand Beige.2.9.9.2 Design: Granite Chips on Mocha.2.9.9.3 Design: Saddle Tan Chips on Sand Beige.2.9.9.4 Design: Satillo Chips on Mocha.2.9.9.5 Design: Sunset Trail Chips on Sand Beige.2.9.9.6 Design: Terrazzo Chips on Mocha.2.9.9.7 Design: Tuxedo Chips on White Night Grey.2.9.9.8 Design: White Granite Chips on White Night Grey.

2.10 COUNTERTOP MIXES

2.10.1 Product: enCOUNTER Mix.2.10.1.1 Type; Blend of rock, medium and fine graded sands, cement and proprietary

performance enhancing ingredients. Used for either a cast-in-place method or pre-casting.

2.10.1.2 Color: White.2.10.1.3 Color: Gray.

2.10.2 Product: enFORMS.2.10.2.1 Type: Perimeter forms with milled designs.2.10.2.2 Designs: Chiseled Sandstone.2.10.2.3 Designs: Coral with Seashells.2.10.2.4 Designs: Split Face Granite.

2.10.3 Product: enCOLOR.2.10.3.1 Type: Pre-dispersed iron oxide pigments solids in an aqueous base liquid.2.10.3.2 Pigment: 066 Liquid Color.2.10.3.3 Pigment: 242 Liquid Color.2.10.3.4 Pigment: 288 Liquid Color.2.10.3.5 Pigment: 388 Liquid Color.2.10.3.6 Pigment: 417 Liquid Color.2.10.3.7 Pigment: 492 Liquid Color.2.10.3.8 Pigment: 500 Liquid Color.2.10.3.9 Pigment: 775 Liquid Color.2.10.3.10 Pigment: 920 Liquid Color.

2.10.4 Product: enFLOW.2.10.4.1 Type: High Range Water Reducer for Concrete Countertops and Sinks.

2.10.5 Product: enFORCE.2.10.5.1 Type: Extra heavy-duty fiber reinforcement.

2.10.6 Product: enMAGIC.2.10.6.1 Type: Trowel-Grade Polymer Modified Cementitious Micro Topping.2.10.6.2 Color: White.2.10.6.3 Color: Gray.

2.10.7 Product: enPOXY.2.10.7.1 Type: Two part 100% epoxy.

2.10.8 Product: enSPARTIC.2.10.8.1 Type: Two-Component (1:1) Polyaspartic Aliphatic Polyurea utilizing innovative

proprietary Nanotechnology.

03 35 00-17

2.11 POLISHING COMPOUNDS

2.11.1 Product: Polishing Densifier.2.11.1.1 Type: Lithium Silicate Concrete Densifier, Hardener, and Sealer.

2.11.2 Product: Polishing Guard.2.11.2.1 Type: Copolymer Blend of High Gloss Sealer And High Performance Lithium

Silicate Densifier.

2.11.3 Product: Interior DYE-namic Acetone Dye.2.11.3.1 Type: Finely ground color particles in solution.2.11.3.2 Color: Black.2.11.3.3 Color: Burnt Sienna.2.11.3.4 Color: Caramel.2.11.3.5 Color: Chestnut.2.11.3.6 Color: Chocolate.2.11.3.7 Color: Dixie Red.2.11.3.8 Color: Eggplant.2.11.3.9 Color: Forest Green.2.11.3.10 Color: Glacier.2.11.3.11 Color: Gold.2.11.3.12 Color: Green.2.11.3.13 Color: Mahogany.2.11.3.14 Color: Midnight Black.2.11.3.15 Color: Raw Sienna.2.11.3.16 Color: Saddle Brown.2.11.3.17 Color: Sand.2.11.3.18 Color: Slate Blue.2.11.3.19 Color: Terra Cotta.2.11.3.20 Color: Turquoise.2.11.3.21 Color: Walnut.2.11.3.22 Color: Yellow.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly prepared.

3.1.2 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

3.2.1 Clean surfaces thoroughly prior to installation.

3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

3.4 VERTICAL MIX INSTALLATION

3.4.1 Product: Vertical Mix:

3.4.2 Application:3.4.2.1 Bond Coat: Roll bond coat over entire surface (SS polymer - full strength). Let

bond coat become tacky.

03 35 00-18

3.4.2.2 Scratch Coat 1st Coat: (diluted polymer (4:1) mixed with bag mix to desired consistency. Used as a base coat for adhesion) using a hawk and trowel, apply a thin coat of SS Vertical Mix to achieve an even scratch coat. Let that coat dry until it has a good set.

3.4.2.3 Texture Coat 2nd Coat: (same as scratch coat, the consistency can be thicker depending on conditions) using a hawk and trowel, apply a texture coat. The thickness of this coat is determined by the texture and pattern chosen. Apply to approximately 1/2 inch (13 mm) for flat textures, and 3/4 inch (19 mm) for stone tool impressions. The consistency of this coat is determined by the amount of area to cover, climate conditions and manpower. Only apply texture coat to a limited area to avoid set before stamping is complete.

3.5 PROTECTION

3.5.1 Protect installed products until completion of project.

3.5.2 Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

03 35 00-19

· Web viewWith substrate wetting agents and anti-foaming additives included in this formulation,...

Documents

Transcript of · Web viewWith substrate wetting agents and anti-foaming additives included in this formulation,...