€¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how?...
Transcript of €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how?...
![Page 1: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/1.jpg)
SECTION 10 51 00LOCKERS
Display hidden notes to specifier. (Don't know how? Click Here)
Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved
1 GENERAL
1.1 SECTION INCLUDES
1.1.1 Metal lockers.
1.1.2 Wood lockers.
1.1.3 Plastic lockers.
1.1.4 Phenolic lockers.
1.1.5 Plastic laminate lockers.
1.1.6 Hybrid wood and stainless steel lockers.1.1.6.1.1 Frame Height: 72 inches (1829 mm).
1.1.7 Hybrid phenolic and stainless steel lockers.
1.2 RELATED SECTIONS
1.2.1 Section 06 10 00 - Rough Carpentry.
1.3 SUBMITTALS
1.3.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.
1.3.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.3.2.1 Preparation instructions and recommendations.1.3.2.2 Storage and handling requirements and recommendations.1.3.2.3 Installation methods.
1.3.3 Shop Drawings: Submit shop drawings showing locker layout, details of construction, numbering sequence if applicable.
1.3.4 Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, color, and patterns.
1.4 QUALITY ASSURANCE
1.4.1 Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.
1.4.2 Installer Qualifications: Minimum 2 year experience installing similar products.
1.4.3 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1.4.3.1 Do not proceed with remaining work until workmanship is approved by Architect.1.4.3.2 Refinish mock-up as required to produce acceptable work.
10 51 00-1
![Page 2: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/2.jpg)
1.5 DELIVERY, STORAGE, AND HANDLING
1.5.1 Deliver and store products in manufacturer's unopened packaging bearing the brand name and manufacturer's identification until ready for installation.
1.5.2 Handling: Handle materials to avoid damage.
1.6 PROJECT CONDITIONS
1.6.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.
1.7 SEQUENCING
1.7.1 Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.
1.8 WARRANTY
1.8.1 Provide manufacturer's standard limited warranty.
2 PRODUCTS
2.1 MANUFACTURERS
2.1.1 Acceptable Manufacturer: Longhorn Lockers, which is located at: P. O. Box 375; Venus, TX 76084; Tel: 972-223-2023; Fax: 972-223-1008; Email:request info ([email protected]); Web:www.longhornlockers.com
2.1.2 Web: http://www.longhornlockers.com.
2.1.3 Substitutions: Not permitted.
2.1.4 Requests for substitutions shall be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
2.2 METAL LOCKERS
2.2.1 Metal Lockers: Conqueror Series as supplied by Longhorn Lockers.2.2.1.1 Style: Open Faced.2.2.1.2 Material: Steel parts shall consist of Galvanealed steel body and stainless
hardware.2.2.1.2.1 Finish: Metal shall be cleaned and prepared using a phosphate for finish
adhesion. Metal components shall receive an electrostatically charged finish for maximum adhesion and wrap. Powder Coat finish.
2.2.1.3 Material: Platinum option - Stainless steel metal components for body.2.2.1.4 Construction: The lockers shall be fully welded to form a one piece rigid
structure. Welds are cleaned and buffed before finish is applied.2.2.1.5 Uni-Frame: The locker sides, shelves and top have a 16ga combined 1 inch (25
mm) dual turn in channel type frame system to give the unit strength and stability.
2.2.1.6 Body: Shelves shall be constructed of 16ga galvanealed steel. Hat shelf shall have a built in coat hanger lip consisting of a 1 inch x1 inch (25 mm x 25 mm) channel valley for the coat hanger to hang from. Sides shall angle back from the top to the seat hinge beam for openness.
2.2.1.7 Footlocker: Shall consist of 16ga Galvanealed steel. Size shall be locker depth and width and shall be no more than 16 inches (406 mm) high. Foot locker shall
10 51 00-2
![Page 3: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/3.jpg)
be ventilated thru means of perforations unless custom logo or lettering is punched in face. Adequate ventilation shall be achieved.
2.2.1.8 Foot Locker Seat Lid: Shall consist of 16ga galvanealed steel and to be formed on all 4 sides with a 1 inch (25 mm) double turn back type frame for strength and stability. A 16ga stiffening channel shall be securely welded to the underside of the seat for strength and rigidity. Seat lid shall be attached to footlocker using a 16ga stainless steel piano type hinge. An 11ga strike lug shall protrude through top lip of footlocker face and into the stainless steel recessed handle.
2.2.1.9 Equipment: Shall consist of 2 AIM Custom HD 11ga stainless back wall hooks, 2 HD 11ga Stainless side wall hooks, built in integrated shelf face coat rod channel.
2.2.1.10 Security Box: Shall consist of a 16ga, Galvanealed steel 12 inches x 12 inches (305 mm by 305 mm) lockable compartment for valuables. Door shall be securely attached to the lock box with a 16ga piano type hinge. A continuous strike shall be achieved by the door face over lapping the side of the box and the stainless strike protruding through the door face inside the stainless handle for use with padlock.
2.2.1.11 Lock: Combination padlocks (optional matching set for foot locker and locker box) - Zephyr Model 1925 Master keyed.
2.2.1.12 Lock: Built-in combination lock - Zephyr Model 1954 Master Keyed.2.2.1.13 Lock: DigiLock APS with Pull - Assigned or shared use.2.2.1.14 Lock: Stealth Lock.2.2.1.15 Lock: As scheduled for custom fitting.2.2.1.16 Seat Lid: Armor - Kevlar Infused, high pressure applied polyurethane applied to
steel seat for protection against wear and tear from cleats.2.2.1.16.1 Color: Standard black color.2.2.1.16.2 Color: Custom color.
2.2.1.17 Seat Lid: Armor Elite - includes Armor option with team logo or lettering impregnated and raised under the poly liner.
2.2.1.18 Seat Lid: Woodsman - 3/8 inch (9.5 mm) thick solid Phenolic with wood grain bench top on top of the steel lid.
2.2.1.19 Seat Lid: Executive Pro - premium anti-microbial vinyl covered 2 inches (51 mm) hi-density foam pad attached to steel seat lid.
2.2.1.20 Seat Lid: Poly Pro - standard vinyl covered 2 inches (51 mm) hi-density foam pad attached to steel seat lid.
2.2.1.21 Full Phenolic Signature Back: The full back is covered with 1/4 inch (6 mm) thick wood grain solid Phenolic panel. Laser and routed insignia as indicated or required.
2.2.1.22 Custom Hooks: Provide 2- HD custom stainless laser etched logo hooks (Signature Hook Option).
2.2.1.23 Full Battle Gear: Provide shoulder pad and helmet gear rack. Shall consist of 1.5 inches (38 mm) round 304 stainless steel tubing fully welded to form rack for drying shoulder pads and helmet in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish.
2.2.1.24 Waterfall Gear Rack: Shall consist of 1.5 inches (38 mm) round stainless steel tubing fully welded to form rack for drying shoulder pads in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with acorn beauty nuts with chrome finish.
2.2.1.25 V-Shaped Shoulder Pad Holder: Shall consist of 16ga galvanealed steel V-shaped. This holder is designed to hold pads in an upside down drying position. Pad holder shall be finished in like manner as locker.
2.2.1.26 Cleat Rack: Cleat rack shall consist of 3/16 inch (4.8 mm) flat iron strap formed for hanging shoes for drying. Rack shall be bolted to the back of footlocker compartment through drilled holes.
2.2.1.27 Electrical: Provide 110v electrical outlet with dual USB charging ports placed in
10 51 00-3
![Page 4: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/4.jpg)
back of lock box. Electrical components shall be inside locker and behind stainless cover panels. Electrical whip to j-box in upper name plate area for electrical hookups by locker manufacturer. Electrical terminations to j-box by electrical trade.
2.2.1.28 Air Raider: Shall include air assisted ventilation system powered by 110 V power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back, up a channel and back out into the room. This circulation shall help prevent mildew, smell and staph infection.
2.2.1.28.1 This system shall be hooked up to the Battle Gear Rack for drying of the pads and helmet.
2.2.1.29 Air Raider Return Air Plenum: Ventilation system powered by facility's return/exhausted air source. System shall use the facility's return or exhausted air source to pull the room air in through the locker, across the wet gear, through perforations in false back, up a channel and into the air handling system or out of the exhaust system. This circulation shall help prevent mildew, smell and staph infection.
2.2.1.30 Slide In Name Plate Holder: 1.5 inches x 8 inches (38 mm x 203 mm) bright aluminum slide in name plate holder. Attached to hat shelf face.
2.2.1.31 Custom Name Plate: 1.5 inches x 8 inches (38 mm x 203 mm) custom laser etched name plate in stainless or color acrylic. Requires slide in name plate holder.
2.2.2 Standard Metal Corridor Lockers:2.2.2.1 Body Construction: Knock down (KD) with 24 gauge solid body components.2.2.2.2 Doors: 16 gauge louvered doors, 18 gauge for 9 inches (229 mm) wide, are
standard.2.2.2.3 Doors: Plain.2.2.2.4 Doors: Secure-Air-Flow.2.2.2.5 Doors: SafetyView.2.2.2.6 Doors: Diamond perforated door.2.2.2.7 Frame: 16 gauge frame with 16 gauge horizontal cross member between doors
on double and triple tier wardrobe lockers.2.2.2.8 Handle: Deep-drawn seamless stainless steel recessed handle.2.2.2.9 Door Strike: Continuous vertical door strike at both hinge and latch side2.2.2.10 Latching: 12 gauge latch hooks MIG welded to frame. Gravity lift-type multi-point
spring loaded latching:2.2.2.10.1 3-point latching for openings 48 inches (1219 mm) high and higher.2.2.2.10.2 2-point latching for openings 20 inches (508 mm) high thru 36 inches (914
mm) high.2.2.2.11 Hinges: 16 gauge continuous piano hinge.2.2.2.12 Hooks: 2-single hooks and 1-double hook is standard. I-double hook only for
triple tier and 1-double and 1- single hook for 9 inches (229 mm) wide openings 30 inches (762 mm) and higher
2.2.2.13 Shelves: Hat shelf for single tier openings 60 inches (1524 mm) and 72 inches (1829 mm) high.
2.2.2.14 All production KD lockers are supplied without legs unless otherwise specified.2.2.2.15 Warranty: 2 years.2.2.2.16 Size: Single Tier.
2.2.2.16.1 Width: 9 inches (229 mm).2.2.2.16.2 Width: 12 inches (305 mm).2.2.2.16.3 Width: 15 inches (381 mm).2.2.2.16.4 Width: 18 inches (457 mm).2.2.2.16.5 Width: 24 inches (610 mm).2.2.2.16.6 Depth: 12 inches (305 mm).2.2.2.16.7 Depth: 15 inches (381 mm).
10 51 00-4
![Page 5: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/5.jpg)
2.2.2.16.8 Depth: 18 inches (457 mm).2.2.2.16.9 Depth: 21 inches (533 mm).2.2.2.16.10 Depth: 24 inches (610 mm).2.2.2.16.11 Opening Height: 36 inches (914 mm).2.2.2.16.12 Opening Height: 48 inches (1219 mm).2.2.2.16.13 Opening Height: 60 inches (1524 mm).2.2.2.16.14 Opening Height: 72 inches (1829 mm).2.2.2.16.15 Frame Height: 36 inches (914 mm).2.2.2.16.16 Frame Height: 48 inches (1219 mm).2.2.2.16.17 Frame Height: 60 inches (1524 mm).2.2.2.16.18 Frame Height: 72 inches (1829 mm).
2.2.2.17 Size: Double Tier.2.2.2.17.1 Width: 9 inches (229 mm).2.2.2.17.2 Width: 12 inches (305 mm).2.2.2.17.3 Width: 15 inches (381 mm).2.2.2.17.4 Width: 18 inches (457 mm).2.2.2.17.5 Depth: 12 inches (305 mm).2.2.2.17.6 Depth: 15 inches (381 mm).2.2.2.17.7 Depth: 18 inches (457 mm).2.2.2.17.8 Depth: 21 inches (533 mm).2.2.2.17.9 Depth: 24 inches (610 mm).2.2.2.17.10 Opening Height: 30 inches (762 mm).2.2.2.17.11 Opening Height: 26 inches (660 mm).2.2.2.17.12 Frame Height: 60 inches (1524 mm).2.2.2.17.13 Frame Height: 72 inches (1829 mm).
2.2.2.18 Size: Triple Tier.2.2.2.18.1 Width: 9 inches (229 mm).2.2.2.18.2 Width: 12 inches (305 mm).2.2.2.18.3 Width: 15 inches (381 mm).2.2.2.18.4 Depth: 12 inches (305 mm).2.2.2.18.5 Depth: 15 inches (381 mm).2.2.2.18.6 Depth: 18 inches (457 mm).2.2.2.18.7 Opening Height: 20 inches (508 mm).2.2.2.18.8 Opening Height: 24 inches (610 mm).2.2.2.18.9 Frame Height: 60 inches (1524 mm).2.2.2.18.10 Frame Height: 72 inches (1829 mm).
2.2.3 Standard KD Athletic Lockers2.2.3.1 Body Construction: Knock down (KD) with l 6 gauge solid top, bottom and
intermediate shelves, 16 gauge diamond perforated sides, 18 gauge solid back.2.2.3.2 Doors: 14 gauge diamond perforated doors are standard.2.2.3.3 Doors: Louvered.2.2.3.4 Doors: Secure-Air-Flow.2.2.3.5 Doors: SafetyView.2.2.3.6 Frame: 16 gauge frame with 16 gauge horizontal cross member between doors
on double and triple tier wardrobe lockers.2.2.3.7 Handle:
2.2.3.7.1 Wardrobe: Deep-drawn seamless stainless steel recessed handle.2.2.3.7.2 Box: Single-point thru-the-door finger pull padlock hasp.
2.2.3.8 Door Strike: Continuous vertical door strike at both hinge and latch side.2.2.3.9 Latching (wardrobe): 12 gauge latch hooks MlG welded to frame. Gravity lift-type
multi-point spring loaded latching:2.2.3.9.1 3-point latching for openings 48 inches (1219 mm) high and higher.2.2.3.9.2 2-point latching for openings 20 inches (508 mm) high thru 36 inches (914
mm) high.2.2.3.10 Hinges: 16 gauge continuous piano hinge.
10 51 00-5
![Page 6: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/6.jpg)
2.2.3.11 Hooks (wardrobe): 2-single hooks and 1-double hook is standard. 1-double hook only for triple tier and 1-double and 1- single hook for 9 inches (229 mm) wide openings 30 inches (762 mm) and higher.
2.2.3.12 Shelves (wardrobe): Hat shelf for single tier openings 60 inches (1524 mm) and 72 inches (1829 mm) high.
2.2.3.13 All production KD lockers are supplied without legs unless otherwise specified.2.2.3.14 Warranty: 2 years.2.2.3.15 Size: Single Tier.
2.2.3.15.1 Width: 9 inches (229 mm).2.2.3.15.2 Width: 12 inches (305 mm).2.2.3.15.3 Width: 15 inches (381 mm).2.2.3.15.4 Width: 18 inches (457 mm).2.2.3.15.5 Width: 24 inches (610 mm).2.2.3.15.6 Depth: 12 inches (305 mm).2.2.3.15.7 Depth: 15 inches (381 mm).2.2.3.15.8 Depth: 18 inches (457 mm).2.2.3.15.9 Depth: 21 inches (533 mm).2.2.3.15.10 Depth: 24 inches (610 mm).2.2.3.15.11 Opening Height: 36 inches (914 mm).2.2.3.15.12 Opening Height: 48 inches (1219 mm).2.2.3.15.13 Opening Height: 60 inches (1524 mm).2.2.3.15.14 Opening Height: 72 inches (1829 mm).2.2.3.15.15 Frame Height: 36 inches (914 mm).2.2.3.15.16 Frame Height: 48 inches (1219 mm).2.2.3.15.17 Frame Height: 60 inches (1524 mm).2.2.3.15.18 Frame Height: 72 inches (1829 mm).
2.2.3.16 Size: Double Tier.2.2.3.16.1 Width: 9 inches (229 mm).2.2.3.16.2 Width: 12 inches (305 mm).2.2.3.16.3 Width: 15 inches (381 mm).2.2.3.16.4 Width: 18 inches (457 mm).2.2.3.16.5 Depth: 12 inches (305 mm).2.2.3.16.6 Depth: 15 inches (381 mm).2.2.3.16.7 Depth: 18 inches (457 mm).2.2.3.16.8 Depth: 21 inches (533 mm).2.2.3.16.9 Depth: 24 inches (610 mm).2.2.3.16.10 Opening Height: 30 inches (762 mm).2.2.3.16.11 Opening Height: 26 inches (660 mm).2.2.3.16.12 Frame Height: 60 inches (1524 mm).2.2.3.16.13 Frame Height: 72 inches (1829 mm).
2.2.3.17 Size: Triple Tier.2.2.3.17.1 Width: 9 inches (229 mm).2.2.3.17.2 Width: 12 inches (305 mm).2.2.3.17.3 Width: 15 inches (381 mm).2.2.3.17.4 Depth: 12 inches (305 mm).2.2.3.17.5 Depth: 15 inches (381 mm).2.2.3.17.6 Depth: 18 inches (457 mm).2.2.3.17.7 Opening Height: 20 inches (508 mm).2.2.3.17.8 Opening Height: 24 inches (610 mm).2.2.3.17.9 Frame Height: 60 inches (1524 mm).2.2.3.17.10 Frame Height: 72 inches (1829 mm).
2.2.3.18 Size: Four Tier.2.2.3.18.1 Width: 12 inches (305 mm).2.2.3.18.2 Width: 15 inches (381 mm).2.2.3.18.3 Depth: 12 inches (305 mm).2.2.3.18.4 Depth: 15 inches (381 mm).
10 51 00-6
![Page 7: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/7.jpg)
2.2.3.18.5 Depth: 18 inches (457 mm).2.2.3.18.6 Opening Height: 15 inches (381 mm).2.2.3.18.7 Opening Height: 18 inches (457 mm).2.2.3.18.8 Frame Height: 60 inches (1524 mm).2.2.3.18.9 Frame Height: 72 inches (1829 mm).
2.2.3.19 Size: Five Tier.2.2.3.19.1 Width: 12 inches (305 mm).2.2.3.19.2 Width: 15 inches (381 mm).2.2.3.19.3 Depth: 12 inches (305 mm).2.2.3.19.4 Depth: 15 inches (381 mm).2.2.3.19.5 Depth: 18 inches (457 mm).2.2.3.19.6 Opening Height: 12 inches (305 mm).2.2.3.19.7 Opening Height: 14.4 inches (366 mm).2.2.3.19.8 Frame Height: 60 inches (1524 mm).2.2.3.19.9 Frame Height: 72 inches (1829 mm).
2.2.3.20 Size: Six Tier.2.2.3.20.1 Width: 12 inches (305 mm).2.2.3.20.2 Width: 15 inches (381 mm).2.2.3.20.3 Depth: 12 inches (305 mm).2.2.3.20.4 Depth: 15 inches (381 mm).2.2.3.20.5 Depth: 18 inches (457 mm).2.2.3.20.6 Opening Height: 12 inches (305 mm).2.2.3.20.7 Frame Height: 72 inches (1829 mm).
2.2.3.21 Electrical: Provide 110v electrical outlet with dual USB charging ports placed in back of lock box. Electrical components shall be inside locker and behind stainless cover panels. Electrical whip to j-box in upper name plate area for electrical hookups by locker manufacturer. Electrical terminations to j-box by electrical trade.
2.2.3.22 Air Raider: Shall include air assisted ventilation system powered by 110 V power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back, up a channel and back out into the room. This circulation shall help prevent mildew, smell and staph infection.
2.2.3.22.1 This system shall be hooked up to the Battle Gear Rack for drying of the pads and helmet.
2.2.3.23 Air Raider Return Air Plenum: Ventilation system powered by facility's return/exhausted air source. System shall use the facility's return or exhausted air source to pull the room air in through the locker, across the wet gear, through perforations in false back, up a channel and into the air handling system or out of the exhaust system. This circulation shall help prevent mildew, smell and staph infection.
2.2.4 Law Enforcement Lockers:2.2.4.1 Wardrobe:
2.2.4.1.1 Locker Series: Sentinel Locker Series as specified.2.2.4.1.2 Locker Configuration:2.2.4.1.3 Locker Size:2.2.4.1.4 Lock:
2.2.4.2 Weapons Lockers:2.2.4.2.1 Locker Series: Sentinel Locker Series as specified.2.2.4.2.2 Locker Configuration:2.2.4.2.3 Locker Size:2.2.4.2.4 Lock:
2.2.4.3 Weapon Racks:2.2.4.3.1 Locker Series: Military Field Gear (TA-50) Locker Series as specified.2.2.4.3.2 Locker Configuration:
10 51 00-7
![Page 8: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/8.jpg)
2.2.4.3.3 Locker Size:2.2.4.3.4 Lock:
2.2.4.4 Duty Bag Lockers:2.2.4.4.1 Locker Series: Sentinel Locker Series as specified.2.2.4.4.2 Locker Configuration:2.2.4.4.3 Locker Size:2.2.4.4.4 Lock:
2.2.4.5 Evidence Lockers:2.2.4.5.1 Locker Series: Sentinel Locker Series as specified.2.2.4.5.2 Locker Configuration:2.2.4.5.3 Locker Size:2.2.4.5.4 Lock:
2.2.4.6 Refrigerated Evidence Lockers:2.2.4.6.1 Locker Series: Longhorn Locker Series as specified.2.2.4.6.2 Locker Configuration:2.2.4.6.3 Locker Size:2.2.4.6.4 Lock:
2.2.5 Firehouse Lockers:2.2.5.1 Locker Series: Model A-1 Locker Series as specified.2.2.5.2 Locker Configuration:2.2.5.3 Locker Size:2.2.5.4 Lock:
2.2.6 Military Lockers:2.2.6.1 Locker Series: Military Field Gear (TA-50) Locker Series as specified.2.2.6.2 Locker Configuration:2.2.6.3 Locker Size:2.2.6.4 Lock:
2.2.7 Coin Operated/Amusement Park Lockers:2.2.7.1 Coin Lockers as supplied by Longhorn lockers.2.2.7.2 Key Operated Lockers as supplied by Longhorn lockers.2.2.7.3 Hasp Lockers as supplied by Longhorn lockers.2.2.7.4 Electronic Locking Lockers as supplied by Longhorn lockers.
2.3 WOOD ATHLETIC LOCKERS
2.3.1 Wood Lockers: Fusion Defender Series as supplied by Longhorn Lockers.2.3.1.1 Material: Steel parts shall consist of mild Galvannealed steel. Metal shall be
cleaned and prepared using a phosphate for finish adhesion. Metal components shall receive an electrostatically charged finish for maximum adhesion and wrap.
2.3.1.2 Material: 16ga #3 finish Stainless Steel metal components.2.3.1.3 Wood Veneer materials shall be grade ' A' Plain Sliced Veneer. Species as
indicated or scheduled. Wood finish shall be any AIM standard finish match with 1 coat vinyl sealer and 2 coats clear semi-gloss hi-build Lacquer.
2.3.1.4 Construction: Heavy Duty Bolt-Through Construction- lockers shall be assembled using Stainless 3/16", 1/4" and 3/8" nuts and bolts.
2.3.1.5 Attached hardware shall be aluminum, stainless or zinc coated steel for corrosion resistance. No attachment hardware shall be smaller than 3/16 inch (4.8 mm) diameter in thickness. No material shall be screwed together. Any attachment shall be through bolted to main locker body/frame.
2.3.1.6 Body: Shall consist of 3/4 inch (19 mm) thick medium density fiber board with a wood veneer face. Wood tape shall be applied to visible edges for edge finish and protection.
2.3.1.7 Body: Shall consist of 3/4 inch (19 mm) thick veneer plywood with MDF cross bands. Wood tape (thermally fused) shall be applied to all visible edges for edge
10 51 00-8
![Page 9: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/9.jpg)
finish and protection.2.3.1.8 Shelves: Shelf shall be constructed of 16ga Stainless Steel. Lower shelf shall
have a built in coat hanger lip consisting of a 1 inch x 1 inch (25 mm x 25 mm) channel valley for the coat hanger to hang from. CNC formed and flanged.
2.3.1.9 Footlocker: Shall consist of 16ga Galvannealed steel. Size shall be locker depth and width and shall be no more than 16 inches (406 mm) high. Foot locker shall be ventilated thru means of perforations unless custom logo or lettering is punched in face. Adequate ventilation shall be achieved.
2.3.1.10 Footlocker: Shall consist of 16ga stainless steel interior box (back, front, sides and bottom). This is a formed and flanged unit that spot welded into a rigid 1 piece unit. There is no exposed raw edges on this stainless box. Top bends shall not be less than 1 inch (25 mm) wide giving the unit a full stiff box construction. Size shall be locker depth and width and shall be no more than 14 inches (356 mm) high. Foot Locker face shall be wood with Perforated Stainless insert. Foot locker shall be ventilated thru means of perforations on Stainless portion of face or bottom concealed. Adequate ventilation shall be achieved. Custom laser cut galvanized 14ga steel logo powder coated in logo colors attached to stainless foot locker face using welded stand offs and stainless bolts through the back of the footlocker face.
2.3.1.11 Security Box: Shall consist of a 16ga, Galvannealed steel 12 inches x 12 inches x 12 inches (305 mm x 305 mm x 305 mm) lockable compartment for valuables. Door shall be securely attached to the lock box frame with a 16ga piano type hinge. A continuous strike shall be achieved by the door frame. Padlock hasp shall protrude through the door face. A stainless steel handle shall be attached to face. Door shall be capable of accepting padlocks or built-in combo locks or digital keypad locks.
2.3.1.12 Lock: Combination padlocks (optional matching set for foot locker and locker box) - Zephyr Model 1925 Master keyed.
2.3.1.13 Lock: Built-in combination lock - Zephyr Model 1954 Master Keyed.2.3.1.14 Lock: DigiLock APS with Pull - Assigned or shared use.2.3.1.15 Lock: Stealth Lock.2.3.1.16 Lock: As scheduled for custom fitting.2.3.1.17 Seat Lid: Armor - high pressure applied polyurethane liner applied to steel seat
top and 3 sides for protection against wear and tear from cleats.2.3.1.18 Seat Lid: Armor Elite - includes Armor option with team logo or lettering
impregnated into the poly liner and with a clear layer of polyurethane for added protection.
2.3.1.19 Seat Lid: Woodsman - 1.25 inches (32 mm) thick Maple or Oak Butcher Block bench top in lieu of the steel lid.
2.3.1.20 Seat Lid: Executive Pro - leather covered 2 inches (51 mm) foam pad attached to steel seat lid
2.3.1.21 Seat Lid: Poly Pro - Vinyl covered 2 inches (51 mm) foam pad attached to steel seat lid. This seat cover shall have a single double stitch down the center for design affect.
2.3.1.22 Cleat Rack: Cleat rack shall consist of 3/8 inch (9.5 mm) steel rod formed for hanging shoes for drying. Rack shall be inserted into back of footlocker compartment through drilled holes and welded to footlocker. Also available inside the footlocker in lieu of above the seat.
2.3.1.23 Shoulder Pad and Helmet Rack. Battle Gear Option: Shall consist of 1.5 inches (38 mm) round stainless steel tubing fully welded to form rack for drying shoulder pads and helmet in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish. This option can also be made without the helmet holding mechanism.
2.3.1.24 Waterfall Gear Rack: Shall consist of 1.5 inches (38 mm) round stainless steel tubing fully welded to form rack for drying shoulder pads in the upright position.
10 51 00-9
![Page 10: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/10.jpg)
Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with acorn beauty nuts with chrome finish.
2.3.1.25 Electrical: Provide 110v electrical outlet with dual USB charging ports placed in back of lock box. Electrical components shall be inside locker and behind stainless cover panels. Electrical whip to j-box in upper name plate area for electrical hookups by locker manufacturer. Electrical terminations to j-box by electrical trade.
2.3.1.26 Air Raider: Shall include air assisted ventilation system powered by 110 V power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back, up a channel and back out into the room. This circulation shall help prevent mildew, smell and staph infection.
2.3.1.26.1 This system shall be hooked up to the Battle Gear Rack for drying of the pads and helmet.
2.3.1.27 Air Raider Return Air Plenum: Ventilation system powered by facility's return/exhausted air source. System shall use the facility's return or exhausted air source to pull the room air in through the locker, across the wet gear, through perforations in false back, up a channel and into the air handling system or out of the exhaust system. This circulation shall help prevent mildew, smell and staph infection.
2.3.2 Wood Lockers: Warchest Series as supplied by Longhorn Lockers.2.3.2.1 Material: Steel parts shall consist of mild Galvannealed steel
2.3.2.1.1 Metal Finish: Metal shall be cleaned and prepared using a phosphate for finish adhesion. All metal components shall receive an electrostatically charged finish for maximum adhesion and wrap.
2.3.2.2 Material: Stainless Steel can be substituted as an Optional Add at an upcharge2.3.2.3 Wood Veneer materials shall be grade ' B2' Birch on 3/4" plywood with thermally
fused Birch edge tape.2.3.2.4 Wood Finish: Wood veneer shall have sand sealer applied with 1 coat of hi-build
Lacquer. Clear Natural finish.2.3.2.5 Wood Finish: Wood veneer shall have sand sealer applied with 1 coat of hi-build
Lacquer. Stain finishes as selected as selected form AIM standard colors.2.3.2.6 Wood Finish: Wood veneer shall have sand sealer applied with 1 coat of hi-build
Lacquer. Custom stain match.2.3.2.7 Construction: Heavy Duty Thru Bolt Construction - lockers shall be assembled
using zinc coated nuts and bolts. Attached hardware shall be stainless or zinc coated steel for corrosion resistance. No attachment hardware shall be smaller than 3/16 inch (4.8 mm) diameter in thickness. Attachment shall be through bolted to main locker body/frame. Glue and Dowel Construction is not acceptable and shall not be allowed.
2.3.2.8 Body: Shall consist of 3/4 inch (19 mm) thick plywood with a wood veneer face. 3mm silver birch edge banding or wood tape shall be applied to all visible edges for maximum protection.
2.3.2.9 Shelf: Shelf shall be constructed of 16ga Galvanealed steel. Lower shelf shall have a built in coat hanger lip consisting of a 1 inch x 1 inch (25 mm x 25 mm) channel valley for the coat hanger to hang from.
2.3.2.10 Footlocker: Shall consist of 16ga Galvanealed steel footlocker face. Size shall be locker depth and width and shall be no more than 16 inches (406 mm) high. Foot locker shall be ventilated thru means of perforations in footlocker face unless custom logo or lettering is punched in face. Adequate ventilation shall be achieved.
2.3.2.11 Foot Locker Seat Lid: Shall consist of 16ga Galvannealed steel and to be formed on all 4 sides with a 1 inch (25 mm) double turn back type frame for strength and stability. A stiffening channel shall be securely welded to the underside of the seat lid for strength and rigidity. Seat lid shall be attached to footlocker using a
10 51 00-10
![Page 11: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/11.jpg)
16ga piano type hinge. An 11ga strike lug shall protrude through top lip of footlocker face and into the recessed handle. A stainless steel scratch plate shall be included in the recessed handle.
2.3.2.12 Equipment: Shall consist of HD 11ga 4 stainless wall hooks, built in integrated shelf face coat rod, stainless scratch plate on footlocker lock recess.
2.3.2.13 Security Box: Shall consist of a 16ga, Galvanealed steel 12 inches x 12 inches (305 mm x 305 mm) lockable compartment for valuables. Door shall be securely attached to the lock box with a 16ga piano type hinge.
2.3.2.14 Lock: Stainless strike protruding through the door face inside the stainless handle for padlock by others (standard).
2.3.2.15 Lock: Combination padlocks (optional matching set for foot locker and locker box) - Zephyr Model 1925 Master keyed.
2.3.2.16 Lock: Built-in combination lock - Zephyr Model 1954 Master Keyed.2.3.2.17 Lock: DigiLock APS with Pull - Assigned or shared use.2.3.2.18 Lock: Stealth Lock.2.3.2.19 Lock: As scheduled for custom fitting.2.3.2.20 Seat Lid: Armor - Kevlar Infused, high pressure applied polyurethane applied to
steel seat for protection against wear and tear from cleats.2.3.2.21 Seat Lid: Armor Elite - includes Armor option with team logo or lettering
impregnated and raised under the poly liner.2.3.2.22 Seat Lid: Woodsman - 1.25 inches (32 mm) thick Maple or Oak butcher block
bench top on top of the stainless steel lid.2.3.2.23 Seat Lid: Executive Pro - leather covered 2 inches (51 mm) hi-density foam pad
attached to steel seat lid2.3.2.24 Seat Lid: Poly Pro - Vinyl covered 2 inches (51 mm) hi-density foam pad
attached to steel seat lid.2.3.2.25 Logos: Laser etched logo in back panel - (Signature Option).2.3.2.26 Hooks: 2- HD Custom stainless laser etched logo hooks (Signature Hook).2.3.2.27 Shoulder Pad and Helmet Gear Rack (Full Battle Gear): Shall consist of 1.5
inches (38 mm) round 304 stainless steel tubing fully welded to form rack for drying shoulder pads and helmet in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish.
2.3.2.28 Slide-In Name Plate Holder: This is a 1.5 inches x 8 inches (38 mm x 203 mm) bright aluminum slide in name plate holder. Attached to hat shelf face.
2.3.2.29 Custom Name Plate: 1.5 inches x 8 inches (38 mm x 203 mm) custom laser etched name plate in stainless acrylic. Requires slide in name plate holders and helmet.
2.3.2.30 Full Battle Gear: Provide shoulder pad and helmet gear rack. Shall consist of 1.5 inches (38 mm) round 304 stainless steel tubing fully welded to form rack for drying shoulder pads and helmet in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish.
2.3.2.31 Waterfall Gear Rack: Shall consist of 1.5 inches (38 mm) round stainless steel tubing fully welded to form rack for drying shoulder pads in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with acorn beauty nuts with chrome finish.
2.3.2.32 Electrical: Provide 110v electrical outlet with dual USB charging ports placed in back of lock box. Electrical components shall be inside locker and behind stainless cover panels. Electrical whip to j-box in upper name plate area for electrical hookups by locker manufacturer. Electrical terminations to j-box by electrical trade.
2.3.2.33 Air Raider: Shall include air assisted ventilation system powered by 110 V power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back, up a channel and back out into the room. This circulation shall help prevent mildew, smell and
10 51 00-11
![Page 12: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/12.jpg)
staph infection.2.3.2.33.1 This system shall be hooked up to the Battle Gear Rack for drying of the
pads and helmet.2.3.2.34 Air Raider Return Air Plenum: Ventilation system powered by facility's
return/exhausted air source. System shall use the facility's return or exhausted air source to pull the room air in through the locker, across the wet gear, through perforations in false back, up a channel and into the air handling system or out of the exhaust system. This circulation shall help prevent mildew, smell and staph infection.
2.3.3 Wood Lockers: Defender Club Series as supplied by Longhorn Lockers.2.3.3.1 Steel Parts: Stainless Steel.2.3.3.2 Wood Body Material: Plastic laminate on particle board substrate.2.3.3.3 Wood Body Material: Plastic laminate on MDF substrate.2.3.3.4 Wood Body Material: Plastic laminate on plywood substrate.2.3.3.5 Plastic Laminate Facing: Standard Wilsonart laminate selection.2.3.3.6 Plastic Laminate Interior: Black melamine.2.3.3.7 Plastic Laminate Interior: Almond melamine.2.3.3.8 Plastic Laminate Interior: Woodgrain melamine.2.3.3.9 Wood Veneer Facing: Wood veneer on MDF substrate.2.3.3.10 Wood Veneer Facing: Wood veneer on plywood substrate.2.3.3.11 Wood Veneer: Plain sliced red oak.2.3.3.12 Wood Veneer: Maple.2.3.3.13 Wood Veneer: Birch.2.3.3.14 Wood Veneer: As selected by Architect.2.3.3.15 Wood Finish: 1 coat sanding sealer and 2 coats clear industrial lacquer.2.3.3.16 Wood Finish: 1 coat sanding sealer and 2 coats clear moisture resistant HD
lacquer.2.3.3.17 Construction: Heavy duty bolt-through construction - lockers assembled using
stainless 3/65 inch, 1/4 inch, and 3/8 nuts and bolts. Attached hardware aluminum, stainless or zinc coated steel for corrosion resistance. No attachment hardware may be smaller than 3/16 inch diameter in thickness. Attachments must be through-bolted to main locker body/frame. Dowel and glue construction is not acceptable and will not be allowed.
2.3.3.18 Body: 5/8 inch or 3/4 inch panels (laminate or wood veneer). 3mm PVC edge banding or wood tape applied to visible edges for maximum protection.
2.3.3.19 Doors: Flat slab, wood veneer.2.3.3.20 Doors: Flat slab, laminate.2.3.3.21 Doors: Flat panel wood.2.3.3.22 Doors: Shaker wood.2.3.3.23 Door Hinges: European concealed overlay hinges.2.3.3.24 Lock: Stainless strike protruding through the door face inside the stainless
handle for padlock by others (standard).2.3.3.25 Lock: Built-in combination lock - Zephyr Model 1954 Master Keyed.2.3.3.26 Lock: Cam key lock.2.3.3.27 Lock: DigiLock APS with Pull - Assigned or shared use.2.3.3.28 Lock: Zephyr digital keypad lock with cam hasp and master key override.2.3.3.29 Shelf/Top/Bottom: Shelf constructed of 18 gauge Type 201 stainless steel. Hat
shelf with built-in coat hanger lip consisting of a 1 by 1 inch channel valley for the coat hanger to hang from. Top and bottom formed and flanged and bolted through to the body. Top and bottom panels ventilated with perforations at front for maximum air flow.
2.3.3.30 Slide-In Name Plate Holder: This is a 1.5 inches x 8 inches (38 mm x 203 mm) bright aluminum slide in name plate holder. Attached to hat shelf face.
2.3.3.31 Custom Name Plate: 1.5 inches x 8 inches (38 mm x 203 mm) custom laser etched name plate in stainless acrylic. Requires slide in name plate holders and
10 51 00-12
![Page 13: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/13.jpg)
helmet.2.3.3.32 Standard Equipment: 4 stainless wall hooks, built in integrated shelf face coat
rod.2.3.3.33 Inside Door Mirror: 10 by 16 inches.2.3.3.34 Inside Door Mirror: 10 by 10 inches.2.3.3.35 Inside Door Mirror: As selected by Architect.2.3.3.36 Door Tray: 10 x 2 x 2 inches, 18 gauge stainless steel.2.3.3.37 Door Tray: 10 x 2 x 5 inches, 18 gauge stainless steel.2.3.3.38 Towel Rod: Stainless steel.2.3.3.39 Electrical: Provide 110v electrical outlet with dual USB charging ports placed in
back of lock box. Electrical components shall be inside locker and behind stainless cover panels. Electrical whip to j-box in upper name plate area for electrical hookups by locker manufacturer. Electrical terminations to j-box by electrical trade.
2.3.3.40 Air Raider: Shall include air assisted ventilation system powered by 110 V power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back, up a channel and back out into the room. This circulation shall help prevent mildew, smell and staph infection.
2.3.3.41 Air Raider Return Air Plenum: Ventilation system powered by facility's return/exhausted air source. System shall use the facility's return or exhausted air source to pull the room air in through the locker, across the wet gear, through perforations in false back, up a channel and into the air handling system or out of the exhaust system. This circulation shall help prevent mildew, smell and staph infection.
2.3.4 Country Club Lockers:2.3.4.1 Locker Series:2.3.4.2 Locker Configuration:2.3.4.3 Locker Size:2.3.4.4 Wood Species:2.3.4.5 Lock:
2.3.5 Sports/Fitness:2.3.5.1 Locker Series: Champions Fusion Defender Locker / War Chest.2.3.5.2 Locker Configuration:2.3.5.3 Locker Size:2.3.5.4 Wood Species:2.3.5.5 Lock:
2.3.6 Stadium & Athletics Lockers:2.3.6.1 Locker Series: Champions Fusion Defender Locker / War Chest.2.3.6.2 Locker Configuration:2.3.6.3 Locker Size:2.3.6.4 Wood Species:2.3.6.5 Lock:
2.4 PLASTIC LOCKERS
2.4.1 Plastic Lockers: Champions Fusion Medalist Series as supplied by Longhorn Lockers.2.4.1.1 Material: Steel parts shall consist of mild Galvanealed steel.
2.4.1.1.1 Finish: All metal shall be cleaned and prepared using a phosphate for finish adhesion. All metal components shall receive an electrostatically charged finish for maximum adhesion and wrap.
2.4.1.2 Material: Type 304 or 316 stainless steel metal components (platinum option).2.4.1.3 Plastic materials shall be solid 1/2 inch (13 mm) thick material (HDPE).2.4.1.4 Construction: Knock Down (KD) lockers shall be assembled using zinc coated
10 51 00-13
![Page 14: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/14.jpg)
nuts and bolts or washer backed aluminum rivets. All attached hardware shall be aluminum, stainless or zinc coated steel for corrosion resistance. No attachment hardware shall be smaller than 3/16 inch (4.8 mm) diameter in thickness. No material shall be screwed together. Any attachment shall be through bolted to main locker body/frame.
2.4.1.5 Body: Shall consist of 1/2 inch (13 mm) thick solid extruded plastic (HDPE).2.4.1.6 Body: Shall consist of 1/2 inch (13 mm) thick solid GREEN LEED material with
100% post-consumer material.2.4.1.7 Shelf: Shelf shall be constructed of 16ga Galvannealed steel. Lower shelf shall
have a built in coat hanger lip consisting of a 1 inch x 1 inch (25 mm x 25 mm) channel valley for the coat hanger to hang from.
2.4.1.8 Footlocker: Shall consist of 16ga Galvanealed steel. Size shall be locker depth and width and shall be no more than 16 inches (406 mm) high. Foot locker shall be ventilated thru means of perforations unless custom logo or lettering is punched in face. Adequate ventilation shall be achieved.
2.4.1.9 Foot Locker Seat Lid: Shall consist of 16ga Galvanealed steel and to be formed on all 4 sides with a 1 inch (25 mm) double turn back type frame for strength and stability. Seat lid shall be attached to footlocker using a 16ga piano type hinge. An 11ga lug shall protrude through top lip of footlocker face and into the recessed handle. A stainless steel scratch plate shall be included in the recessed handle.
2.4.1.10 Equipment: Shall consist of 4 stainless wall hooks, built in integrated shelf face coat rod, stainless scratch plate on footlocker lock recess.
2.4.1.11 Lockable Compartment: 12 inches x 12 inches x 12 inches (305 mm x 305 mm x 305 mm) lockable compartment for valuables. Door shall be securely attached to the lock box frame with a 16ga piano type hinge. A continuous strike shall be achieved by the door frame. Padlock hasp shall protrude through the door face. A stainless steel handle shall be attached to face. Door shall be capable of accepting padlocks or built-in combo locks or digital keypad locks.
2.4.1.12 Lock: Combination padlocks (optional matching set for foot locker and locker box) - Zephyr Model 1925 Master keyed.
2.4.1.13 Lock: Built-in combination lock - Zephyr Model 1954 Master Keyed.2.4.1.14 Lock: DigiLock APS with Pull - Assigned or shared use.2.4.1.15 Lock: Stealth Lock.2.4.1.16 Lock: As scheduled for custom fitting.2.4.1.17 Seat Lid: Armor - high pressure applied polyurethane liner applied to steel seat
top and 3 sides for protection against wear and tear from cleats.2.4.1.18 Seat Lid: Armor Elite - includes Armor option with team logo or lettering
impregnated into the poly liner and with a clear layer of polyurethane for added protection.
2.4.1.19 Seat Lid: Poly Pro - Vinyl covered 2 inches (51 mm) foam pad attached to steel seat lid.
2.4.1.20 Cleat Rack: Cleat rack shall consist of 3/8 inch (9.5 mm) steel rod formed for hanging shoes for drying. Rack shall be inserted into back of footlocker compartment through drilled holes and welded to footlocker. Also available inside the footlocker in lieu of above the seat. Refer to drawings.
2.4.1.21 Punched Personalization. Branded Option: Lettering and/or logo applied to foot locker face for ventilation and personalization using either perforation punch press method, plasma or laser method.
2.4.1.22 Shoulder Pad and Helmet Rack. Battle Gear Option: Shall consist of 1.5 inches (38 mm) round stainless steel tubing fully welded to form rack for drying shoulder pads and helmet in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish. This option can also be made without the helmet holding mechanism. Refer to drawings.
2.4.1.23 Shoulder Pad Holder: Shall consist of 16ga Galvannealed steel V-shaped pad
10 51 00-14
![Page 15: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/15.jpg)
holder. This holder is designed to hold pads in an upside down drying position. Pad holder shall be finished in like manner as locker.
2.4.1.24 Electrical: Provide 110v electrical outlet with dual USB charging ports placed in back of lock box. Electrical components shall be inside locker and behind stainless cover panels. Electrical whip to j-box in upper name plate area for electrical hookups by locker manufacturer. Electrical terminations to j-box by electrical trade.
2.4.1.25 Air Raider: Shall include air assisted ventilation system powered by 110 V power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back, up a channel and back out into the room. This circulation shall help prevent mildew, smell and staph infection.
2.4.1.25.1 This system shall be hooked up to the Battle Gear Rack for drying of the pads and helmet.
2.4.1.26 Air Raider Return Air Plenum: Ventilation system powered by facility's return/exhausted air source. System shall use the facility's return or exhausted air source to pull the room air in through the locker, across the wet gear, through perforations in false back, up a channel and into the air handling system or out of the exhaust system. This circulation shall help prevent mildew, smell and staph infection.
2.4.2 Plastic Stadium & Athletics Lockers:2.4.2.1 Locker Series: Champions Fusion Medalist Locker.2.4.2.2 Locker Configuration:2.4.2.3 Locker Size:2.4.2.4 Lock:
2.4.3 Plastic Aquatic Lockers2.4.3.1 Locker Series: Champions Fusion Medalist Locker.2.4.3.2 Locker Configuration:2.4.3.3 Locker Size:2.4.3.4 Lock:
2.5 PHENOLIC LOCKERS
2.5.1 Phenolic Lockers: Champions Fusion Hero Series as supplied by Longhorn Lockers.2.5.1.1 Steel Material: Steel parts shall consist of galvanealed steel.
2.5.1.1.1 Finish: Metal shall be cleaned and prepared using a phosphate for finish adhesion. All metal components shall receive an electrostatically charged finish for maximum adhesion and wrap.
2.5.1.2 Steel Material: Stainless steel metal components. (platinum option)2.5.1.3 Material: Phenolic materials shall be standard black core made by Wilsonart.2.5.1.4 Construction: Knock Down (KD) - lockers shall be assembled using zinc coated
nuts and bolts or washer backed aluminum rivets. All attached hardware shall be aluminum, stainless or zinc coated steel for corrosion resistance. No attachment hardware shall be smaller than 3/16 inch (4.8 mm) diameter in thickness. Any attachment shall be through bolted to main locker body/frame.
2.5.1.5 Body: Shall consist of 3/8 inch (9.5 mm) solid phenolic sides attached with predrilled pilot holes and stainless screws into 1/2 inch (13 mm) thick solid phenolic top, bottom and back.
2.5.1.6 Shelf: Shelf shall be constructed of 16ga Galvanealed steel. Lower shelf shall have a built in coat hanger lip consisting of a 1 inch x 1 inch (25 mm x 25 mm) channel valley for the coat hanger to hang from.
2.5.1.7 Footlocker: Shall consist of Galvanealed steel. Size shall be locker depth and width and shall be no more than 16 inches (406 mm) high. Foot locker shall be ventilated thru means of perforations unless custom logo or lettering is punched
10 51 00-15
![Page 16: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/16.jpg)
in face. Adequate ventilation shall be achieved.2.5.1.8 Foot locker Seat Lid: Shall consist of 16ga galvanealed steel and to be formed
on all 4 sides with a 1 inch (25 mm) double turn back type frame for strength and stability. Seat lid shall be attached to footlocker using a 16ga piano type hinge. Seats, depending on size, shall have stiffener channels welded to the underside of the seat lid. An 11ga stainless strike lug shall protrude through top lip of footlocker face and into the recessed handle. A stainless steel scratch plate shall be included in the recessed handle.
2.5.1.9 Equipment: Shall consist of 2 custom HD 11ga 304 stainless back wall hooks, 2 HD 11ga 304 Stainless side wall hooks, built in integrated shelf face coat rod, stainless scratch plate on footlocker lock recess.
2.5.1.10 Security Box: Door shall be securely attached to the lock box with a 16ga piano type hinge. A continuous strike shall be achieved by the door face over lapping the side of the box and the Stainless strike protruding through the door face inside the Stainless handle. All type locks are available for this lock box. Please specify lock type.
2.5.1.10.1 Size: Shall consist of a 16ga, Galvanealed steel 12 inches x 12 inches (305 mm x 305 mm) lockable compartment for valuables.
2.5.1.11 Lock: Combination padlocks (optional matching set for foot locker and locker box) - Zephyr Model 1925 Master keyed.
2.5.1.12 Lock: Built-in combination lock - Zephyr Model 1954 Master Keyed.2.5.1.13 Lock: DigiLock APS with Pull - Assigned or shared use.2.5.1.14 Lock: Stealth Lock.2.5.1.15 Lock: As scheduled for custom fitting.2.5.1.16 Seat Lid: Armor - Kevlar Infused, high pressure applied polyurethane applied to
steel seat top and 3 sides for protection against wear and tear from cleats.2.5.1.17 Seat Lid: Armor Elite - includes Armor option with team logo or lettering
impregnated into the poly liner and with a clear layer of polyurethane for added protection.
2.5.1.18 Seat Lid: Executive Pro - leather covered 2 inches (51 mm) foam pad attached to steel seat lid
2.5.1.19 Seat Lid: Poly Pro - Vinyl covered 2 inches (51 mm) foam pad attached to steel seat lid.
2.5.1.20 Cleat Rack: Cleat rack shall consist of 3/16 inch (4.8 mm) steel strap formed for hanging shoes for drying. Rack shall be Hinge beam of footlocker compartment through drilled holes. These are available as painted or Armor Coated.
2.5.1.21 Punched Personalization (Branded Option): Lettering and/or logo shall be applied to foot locker face or lock box door for ventilation and personalization using either perforation punch press method, plasma or laser method.
2.5.1.22 Optional Branded Item: Custom number plates attached to the door face 6 inches x 6 inches (152 mm x 152 mm) laser cut.
2.5.1.23 Signature Option: 16 inches (406 mm) team's logo is routered into the back panel.
2.5.1.24 Shoulder Pad and Helmet Gear Rack. Battle Gear Option: Shall consist of 1.5 inches (38 mm) round 304 stainless steel tubing fully welded to form rack for drying shoulder pads and helmet in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish.
2.5.1.25 Shoulder Pad Gear Rack. Waterfall Gear Option: Shall consist of 1.5 inches (38 mm) round 304 stainless steel tubing fully welded to form rack for drying shoulder pads in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish.
2.5.1.26 Air Raider Option: Shall include air assisted ventilation system powered by hardwired power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back,
10 51 00-16
![Page 17: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/17.jpg)
up a channel and back out into the room. This circulation shall help prevent mildew, smell and staph infection. This system can also be hooked up to the Battle Gear Rack for drying of the pads and helmet. Refer to drawings.
2.5.2 Phenolic Stadium & Athletics Lockers2.5.2.1 Locker Series: Champions Fusion Hero Locker.2.5.2.2 Locker Configuration:2.5.2.3 Locker Size:2.5.2.4 Lock:
2.5.3 Phenolic Personnel Lockers2.5.3.1 Locker Series: Champions Fusion Hero Locker.2.5.3.2 Locker Configuration:2.5.3.3 Locker Size:2.5.3.4 Lock:
2.5.4 Phenolic Firehouse Lockers2.5.4.1 Locker Series: Champions Fusion Hero Locker.2.5.4.2 Locker Configuration:2.5.4.3 Locker Size:2.5.4.4 Lock:
2.5.5 Phenolic Aquatic Lockers2.5.5.1 Locker Series: Champions Fusion Hero Locker.2.5.5.2 Locker Configuration:2.5.5.3 Locker Size:2.5.5.4 Lock:
2.6 PLASTIC LAMINATE LOCKERS
2.6.1 Plastic Laminate Lockers: Champions Fusion Challenger Series as supplied by Longhorn Lockers.2.6.1.1 Material: Steel parts shall consist of mild Galvannealed steel
2.6.1.1.1 Finish: All metal shall be cleaned and prepared using a phosphate for finish adhesion. All metal components shall receive an electrostatically charged finish for maximum adhesion and wrap.
2.6.1.2 Material: Stainless steel metal components.2.6.1.3 Plastic Laminate materials shall standard Wilsonart selections on 5/8 inch (16
mm) particle board or medium density fiber board.2.6.1.4 Construction: Knock Down (KD) lockers shall be assembled using zinc coated
nuts and bolts or washer backed aluminum rivets. All attached hardware shall be aluminum, stainless or zinc coated steel for corrosion resistance. No attachment hardware shall be smaller than 3/16 inch (4.8 mm) diameter in thickness. Any attachment shall be through bolted to main locker body/frame.
2.6.1.5 Body: Shall consist of 5/8 inch (9.5 mm) thick particle board or medium density fiber board with a melamine backer and vertical grade laminate face. 3 mm PVC edge banding shall be applied to all visible edges for maximum protection.
2.6.1.6 Shelf: Shelf shall be constructed of 16ga Galvanealed steel. Lower shelf shall have a built in coat hanger lip consisting of a 1 inch x 1 inch (25 mm x 25 mm) channel valley for the coat hanger to hang from.
2.6.1.7 Footlocker: Shall consist of 16ga Galvanealed steel. Size shall be locker depth and width and shall be no more than 16 inches (406 mm) high. Foot locker shall be ventilated thru means of perforations unless custom logo or lettering is punched in face. Adequate ventilation shall be achieved.
2.6.1.8 Foot Locker Seat Lid: Shall consist of 16ga Galvannealed steel and to be formed on all 4 sides with a 1 inch (25 mm) double turn back type frame for strength and stability. Seat lid shall be attached to footlocker using a 16ga piano type hinge.
10 51 00-17
![Page 18: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/18.jpg)
An 11ga lug shall protrude through top lip of footlocker face and into the recessed handle. A stainless steel scratch plate shall be included in the recessed handle.
2.6.1.9 Equipment: Shall consist of 4 stainless wall hooks, built in integrated shelf face coat rod, stainless scratch plate on footlocker lock recess.
2.6.1.10 Large Security Box: Shall consist of a 16ga, Galvannealed steel 12 inches x 12 inches x 12 inches (305 mm x 305 mm x 305 mm) lockable compartment for valuables. Door shall be securely attached to the lock box frame with a 16ga piano type hinge. A continuous strike shall be achieved by the door frame. Padlock hasp shall protrude through the door face. A stainless steel handle shall be attached to face. Door shall be capable of accepting padlocks or built-in combo locks or digital keypad locks.
2.6.1.11 Lock: Combination padlocks (optional matching set for foot locker and locker box) - Zephyr Model 1925 Master keyed.
2.6.1.12 Lock: Built-in combination lock - Zephyr Model 1954 Master Keyed.2.6.1.13 Lock: DigiLock APS with Pull - Assigned or shared use.2.6.1.14 Lock: Stealth Lock.2.6.1.15 Lock: As scheduled for custom fitting.2.6.1.16 Seat Lid: Armor - high pressure applied polyurethane liner applied to steel seat
top and 3 sides for protection against wear and tear from cleats.2.6.1.17 Seat Lid: Armor Elite - includes Armor option with team logo or lettering
impregnated into the poly liner and with a clear layer of polyurethane for added protection.
2.6.1.18 Seat Lid: Executive Pro - leather covered 2 inches (51 mm) foam pad attached to steel seat lid
2.6.1.19 Seat Lid: Poly Pro - Vinyl covered 2 inches (51 mm) foam pad attached to steel seat lid.
2.6.1.20 Cleat Rack: Cleat rack shall consist of 3/8 inch (9.5 mm) steel rod formed for hanging shoes for drying. Rack shall be inserted into back of footlocker compartment through drilled holes and welded to footlocker. Also available inside the footlocker in lieu of above the seat. Refer to drawings.
2.6.1.21 Punched Personalization. Branded Option: Lettering and/or logo shall be applied to foot locker face for ventilation and personalization using either perforation punch press method, plasma or laser method.
2.6.1.22 Shoulder Pad and Helmet Rack. Battle Gear Option.: Shall consist of 1.5 inches (38 mm) round stainless steel tubing fully welded to form rack for drying shoulder pads and helmet in the upright position. Designed for use on top of the locker. Gear rack shall thru-bolt using 6-1/4 inches (159 mm) bolts and secured with vinyl lined acorn beauty nuts with chrome finish. This option can also be made without the helmet holding mechanism. Refer to Drawings.
2.6.1.23 Shoulder Pad Holder: Shall consist of 16ga Galvannealed steel V-shaped pad holder. This holder is designed to hold pads in an upside down drying position. Pad holder shall be finished in like manner as locker.
2.6.1.24 Air Raider Option: Shall include air assisted ventilation system powered by 110 V power source. This system shall use a low voltage fan to pull the fresh air in the foot locker face, across the wet gear, through perforations in false back, up a channel and back out into the room. This circulation shall help prevent mildew, smell and staph infection. This system can also be hooked up to the Battle Gear Rack for drying of the pads and helmet. Refer to drawings.
2.6.2 Plastic Laminate Personnel Lockers2.6.2.1 Locker Series: Champions Fusion Challenger Locker.2.6.2.2 Locker Configuration:2.6.2.3 Locker Size:2.6.2.4 Plastic Laminate:2.6.2.5 Lock:
10 51 00-18
![Page 19: €¦ · Web viewSECTION 10 51 00. LOCKERS. Display hidden notes to specifier. (Don't know how? Click Here). Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved ** NOTE TO ...](https://reader035.fdocuments.in/reader035/viewer/2022081714/5faf678e2e529a4b9031951a/html5/thumbnails/19.jpg)
3 EXECUTION
3.1 EXAMINATION
3.1.1 Do not begin installation until substrates have been properly prepared.
3.1.2 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
3.2 PREPARATION
3.2.1 Clean surfaces thoroughly prior to installation.
3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
3.3 INSTALLATION
3.3.1 Install in accordance with manufacturer's instructions and in proper relationship with adjacent construction. Test for proper operation and adjust until satisfactory results are obtained.
3.4 PROTECTION
3.4.1 Protect installed products until completion of project.
3.4.2 Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION
10 51 00-19