Weaver's Cove Energy Offshore Design Codes and Standards

WEAVER'S COVE ENERGYWEAVER’S COVE OFFSHORE BERTH PROJECT

Resource Report 13

APPENDIX D

DESIGN CODES AND STANDARDS

WEAVER'S COVE ENERGY WEAVER’S COVE OFFSHORE BERTH PROJECT

Resource Report 13

13.D-1

13.D DESIGN CODES AND STANDARDS The following federal agencies have been assigned the tasks of permitting the construction and operation of LNG facilities.

• Federal Energy Regulatory Commission – Site selection, design and construction • US Coast Guard (USCG) – Marine design, assessment of waterway suitability • Pipeline and Hazardous Materials Safety Administration (PHMSA) – Prepares and

enforces LNG safety regulations in 49 CFR (Code of Federal Regulations) The jurisdiction of FERC is shown in Figure 13.D-1 below:

Figure 13.D-1. Federal Agency Jurisdiction

The LNG Transfer System design and construction are to comply with the applicable US Federal Government Regulations, specifically:

1. 33 CFR Part 127, which references: 2. ASME B31.3-1993 - Process Piping - ASME Code for Pressure Piping, B31 3. NFPA 59A, Standard for the Production, Storage, and Handling of Liquefied Natural Gas

(LNG), 1994 Edition 4. Other documents incorporated by reference in 33 CFR Part 127 para. 127.003

Other documents selected as design and engineering guidance1 for this project include those provided in the following sections. The list provided here is not meant to be exclusive.

1 Guidance is intended to mean that these documents will be adopted for use to extent practicable and

where they do not conflict with mandatory requirements listed in 33 CFR Part 127


Resource Report 13

13.D-2

1.0 LOCAL CODES

Local codes, as applicable.

2.0 ACI AMERICAN CONCRETE INSTITUTE

Concrete Formwork US Product Standard PS-1 "Construction and Industrial Plywood" ACE 117/117R Standard Specifications for Tolerances for Concrete Construction and

Materials and Commentary ACI 301 Specifications for Structural Concrete AC1 302.1R Guide for Concrete Floor and Slab Construction ACI 304R Guide for Measuring, Mixing, Transporting, and Placing Concrete ACI 305R Hot Weather Concreting ACI 306R Cold Weather Concreting ACE 308.1 Standard Specification for Curing Concrete AC1 315 Details and Detailing of Concrete Reinforcement ACI 318/318R Building Code Requirements for Structural Concrete and Commentary ACI 347 Guide to Formwork for Concrete AC1 357R Guide for the Design and Construction of Fixed Offshore Concrete

Structures ACI 372R Design and Construction of Circular Wire and Strand Wrapped Pre-

stressed Concrete Structures AC1 373R Design and Construction of Circular Pre-stressed Concrete Structures

with Circumferential Tendons ACI SP-66 American Concrete Institute Detailing Manual

3.0 AEIC ASSOCIATION OF EDISON ILLUMINATING COMPANIES

AEIC CS6 Specifications for Ethylene Propylene Rubber Insulated Shielded Power Cables Rated 5 through 69kV

4.0 AFBMA ANTI-FRICTION BEARING MANUFACTURERS ASSOCIATION, INC.

AFBMA 9 Load Ratings and Fatigue Life for Ball Bearings

5.0 AGA AMERICAN GAS ASSOCIATION

AGA Section 4.3.5 Operating Section Report, Purging Principles and Practice AGA XFO277 Classification of Gas Utility Areas for Electrical Installations

6.0 AGMA AMERICAN GEAR MANUFACTURERS ASSOCIATION

AGMA 350.04 1981 Lubrication of Industrial Enclosed Gear Drives


Resource Report 13

13.D-3

7.0 AISC AMERICAN INSTITUTE OF STEEL CONSTRUCTION

Specification for the Design, Fabrication and Erection of Structural Steel for Buildings and Code of Standard Practice for Steel and Bridges AISC S302 Code of Standard Practice for Steel Buildings and Bridges AISC S326 Design, Fabrication, and Erection of Structural Steel for Buildings, with

Supplements AISC S329 Allowable Stress Design Specification for Structural Joints Using ASTM A

325 or ASTM A 490 Bolts Manual of Steel Construction Allowable Stress Design LRFD Manual of Steel Construction

8.0 ANSI AMERICAN NATIONAL STANDARDS INSTITUTE

ANSI B1.20.1 Pipe Threads, General Purpose (Inch) ANSI B16.5 Pipe Flanges and Flanged Fittings: NPS 1/2 through 24 ANSI B16.9 Factory-Made Wrought Steel Buttwelding Fittings ANSI B16.11 Forge Steel Fittings, Socket-Welding and Threaded ANSI B16.31 Non-Ferrous Pipe Flanges ANSI B18.22.1 Plain Washers ANSI B31.3 Chemical Plant and Petroleum Refinery Piping ANSI B96.1 Welded Aluminum-Alloy Storage Tanks ANSI B16.5 Pipe Flanges and Flanged Fittings ANSI B36.10 Steel Pipe ANSI B36.19 Stainless Steel Pipe ANSI C2 National Electrical Safety Code ANSI C37.16 Low-Voltage Power Circuit Breakers and AC Power Circuit Protectors,

Preferred Ratings, Related Requirements and Application Recommendations

ANSI C37.17 Trip Devices for AC and General Purpose DC Low-Voltage Power Circuit Breakers

ANSI 037.50 Switchgear - Low-Voltage AC Power Circuit Breakers Used in Enclosures - Test Procedures

ANSI C37.51 Switchgear - Metal-Enclosed Low-Voltage AC Power Circuit Breaker Switchgear Assemblies - Conformance Test Procedures

ANSI C37.100 Definitions For Power Switchgear ANSI C39.1 Requirements for Electrical Analog Indicating Instruments ANSI C80.1 (1990) Rigid Steel Conduit - Zinc Coated ANSI S 1.11 Specification for Octave-Band and Fractional Octave-Band Analog and

Digital Filters ANSI S 12 .1 Acoustics - Measurement of Airborne Noise Emitted by Information

Technology and Telecommunications Equipment ANSI S12.13 Part I, Performance Requirements, Combustible Gas Detectors, 1986


Resource Report 13

13.D-4

9.0 API AMERICAN PETROLEUM INSTITUTE

API 5L Specification for Line Pipe API 6D Specification for Pipeline Valves API 500 Electrical Classification API 520 Sizing, Selection, and Installation of Pressure-Relieving Devices in

Refineries Part I - Sizing and Selection Part II – Installation

API 521 Guide for Pressure-Relieving and Depressuring Systems API 526 Flanged Steel Safety Relief Valves API 527 Commercial Seat Tightness of Safety Relief Valves with Metal-to-Metal

Seats API 589 Fire Test for Evaluation of Valve Stem Packing API 598 Valve Inspection and Testing API 607 Fire Test for Soft Seated Ball Valves API 609 Butterfly Valves: Double Flanged, Lug and Wafer Type API 614 Lubrication Shaft - Sealing and Control - Oil Systems for Special-Purpose

Applications API 620 Design and Construction of Large, Welded, Low-Pressure Storage Tanks API 653 Tank Inspection, Repair, Alteration and Reconstruction API 2000 Venting Atmospheric and Low-Pressure Storage Tanks Non-refrigerated

and Refrigerated API/PIP 582 Recommended Practice and Supplementary Welding Guidelines for the

Chemical, Oil and Gas Industries API MPM CH 2.2B Manual of Petroleum Measurement Standards: Tank Calibration -

Calibration of Upright Cylindrical Tanks Using the Optical Reference Line Method

API RP2A Planning, Designing and Constructing Fixed Offshore Platforms API RP 6F Fire Test for Soft Seated Ball Valves API RP 14C Recommended Practice for Analysis, Design, Installation, and Testing of

Basic Surface Safety Systems for Offshore Production Platforms-Seventh Edition

API RP 14G Fire Prevention and Control on Open Type Offshore Production Platforms API RP 14J Recommended Practice for Design and Hazards Analysis for Offshore

Production Facilities-Second Edition API RP 500 Recommended Practice For Classification of Locations For Electrical

Installations API RP 520 Sizing, Selection, and Installation of Pressure-Relieving Devices in

Refineries; Part I - Sizing and Selection-Seventh Edition and Part II - Installation

API RP 521 Pressure-relieving and Depressuring Systems-Fifth Edition; Incorporates Errata: 6/2007 and Addendum: 5/2008

API RP 540 Electrical Installations in Petroleum Processing Plants API RP 550 Manual on Installation of Refinery Instruments and Control Systems API RP 1111 Design, Construction, Operation, and Maintenance of Offshore


Resource Report 13

13.D-5

Hydrocarbon Pipelines (Limit State Design) - Third Edition, (1997) API RP 2003 Protection Against Ignitions Arising Out of Static, Lightning and Stray

Currents, 1991 API LRFD RP2A Planning, Designing and Constructing Fixed Offshore Platforms -Load

and Resistance Factor Design API RP 550 Article 2, Section 1 – Analyzers API RP 2350 Overfill Protection for Storage Tanks In Petroleum API Standard 12D Field Welded Tanks for Storage of Production Liquids API Standard 12F Shop Welded Tanks for Storage of Production Liquids API Standard 601 Metallic Gaskets API Standard 620 Design and Construction of Large, Welded, Low Pressure Storage Tanks API Standard 650 Welded Steel Tanks for Oil Storage API Standard 660 Shell and Tube Heat Exchangers for General Refinery Services API Pub 2030 Guidelines for Application of Fixed Water Spray Systems for Fire

Protection in the Petroleum Industry

10.0 ASCE AMERICAN SOCIETY OF CIVIL ENGINEERS

5E1/ASCE 7-02 Minimum Design Loads for Buildings and Other Structures Wind and Seismic

11.0 ASME AMERICAN SOCIETY OF MECHANICAL ENGINEERS

Boiler and Pressure Vessel Code, including Mandatory Addenda ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form) ASME B1.20.1 Pipe Threads, General Purpose (Inch) ASME B16.5 Pipe Flanges and Flanged Fittings ASME B16.21 Nonmetallic Flat Gaskets For Pipe Flanges ASME B16.25 Buttwelding Ends ASME B16.34 Valves – Flanged, Threaded and Welding End ASME B16.47 Series A 150# through 900# 26 Inch through 60 Inch ASME B31.1 Power Piping ASME B31.3 Process Piping, 1993 ASME B31.5 Refrigeration Piping ASME B31.8 Gas Transmission and Distribution Piping Systems ASME B32.3 Piping Systems ASME B46.1 Surface Texture, Surface Roughness, Waviness and Lay Process Piping ASME PTC 25 Pressure Relief Devices ASME PTC 25.3 Safety and Relief Valves ASME Section II Material Specifications: Part A (Ferrous), Part B (Nonferrous), Part C

(Weld Filler Metal), Part D (Properties) ASME Section V Non-Destructive Examination ASME, Section VIII Boiler and Pressure Vessel Code, Divisions 1 and 2, and Alternative

Rules


Resource Report 13

13.D-6

ASME Section IX Boiler and Pressure Vessel Code - Qualification Standard for Welding and Brazing Procedures, Welders, Braziers, and Welding and Brazing Operators

12.0 ASME/ANSI AMERICAN NATIONAL STANDARDS INSTITUTE

13.0 ASNT AMERICAN SOCIETY FOR NONDESTRUCTIVE TESTING

ASNT 2504 Standard for Qualification and Certification of Nondestructive Testing Personnel

14.0 ASTM AMERICAN SOCIETY FOR THE TESTING OF MATERIALS

ASTM A6/A6M Specification for General Requirements for Rolled Steel Plates, Shapes, Sheet Piling, and Bars for Structural Use

ASTM A20/A2OM Specification for General Requirements for Steel Plates for Pressure Vessels

ASTM A36/A36M Specification for Structural Steel ASTM A48/A48M Specification for Gray Iron Castings ASTM A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc Coated,

Welded and Seamless ASTM A82 Specification for Steel Wire, Plain, for Concrete Reinforcement ASTM A90/90M Test Method for Weight (Mass) of Coating on Iron and Steel Articles

with Zinc or Zinc-Alloy Coatings ASTM A105/A105M Specification for Carbon Steel Forgings for Piping Applications ASTM A123/A123M Specification for Zinc (Hot-Galvanized) Coatings on Products Coatings

on Iron and Steel Products ASTM A139/A139M Specification for Electric-Fusion (Arc) - Welded Steel Pipe (NPS 4 and

over) ASTM A143/A143M Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized

Structural Steel Products and Procedure for detecting Embrittlement ASTM A153/A153M Specification for Zinc Coating (Hot Dip) on Iron and Steel Hardware ASTM A167 Specification for Stainless and Heat-Resisting Chromium - Nickel Steel

Plate, Sheet and Strip ASTM A182/A182M Specification for Forged or Rolled Alloy Steel Pipe Flanges, Forged

Fittings and Valves and Parts for High-Temperature Service ASTM A193/A193M Specification for Alloy-Steel and Stainless Steel Bolting Materials for

High-Temperature Service ASTM A194/A194M Specifications for Carbon and Alloy Steel Nuts for High-Pressure of

High-Temperature Service, or Both ASTM A216/A216M Specification for Steel Castings, Carbon, Suitable for Fusion Welding,

for High-Temperature Service ASTM A217/A217M Specification for Steel Casting, Martensitic Stainless and Alloy, for

Pressure-Containing Parts, Suitable for High-Temperature Service ASTM A234 Standard Specification for Piping Fittings of Wrought Carbon Steel and


Resource Report 13

13.D-7

Alloy Steel for Moderate and High Temperature Service ASTM A245 For Sheet Metal Used in the Steelwork ASTM A252 Standard Specification for Welded and Seamless Steel Pipe Piles ASTM A283 Standard Specification for Low and Intermediate Tensile Strength

Carbon Steel Plates ASTM A307 Carbon Steel Externally Threaded Standard Fasteners ASTM A320 Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch

Toughness Testing for Piping Components ASTM A325 Standard Specification for Structural Bolts, Steel, Heat Treated,

120/105 ksi Minimum Tensile Strength ASTM A328 Standard Specification for Steel Sheet Piling ASTM A366 Standard Specification for Steel, Sheet, Carbon, Cold-Rolled

Commercial Quality ASTM A350 Standard Specification for Carbon and Low-Alloy Steel Forgings,

Requiring Notch Toughness testing for Pipe Components ASTM A351 Specification for Castings, Austenitic, Austenitic-Ferric (Duplex), for

Pressure-Containing Parts ASTM A352 Standard Specification for Steel Castings, Ferritic and Martensitic for

Pressure-Containing Parts, Suitable for Low-Temperature Service ASTM A370 Test Methods and Definitions for Mechanical Testing of Steel Products ASTM A384 Standard Practice for Safeguarding Against Warpage and Distortion

during Hot-Dip Galvanizing of Steel Assemblies ASTM A385 Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip) ASTM A403 Standard Specification for Wrought Austenitic Stainless Steel Piping

Fittings ASTM A416 Standard Specification for Steel Strand, Uncoated Seven-Wire for

Prestressed Concrete ASTM A420 Standard Specification for Pipe Fittings of Wrought Carbon Steel and

Alloy Steel for Low-Temperature Service ASTM A449 Quenched and Tempered Steel Bolts and Studs ASTM A463 Steel Sheet, Aluminum-Coated, by the Hot Dip Process ASTM A490 (1989) Heat-Treated Steel Structural Bolts; 150 PSI Minimum Tensile

Strength ASTM A493 Stainless and Heat Resisting Steel for cold Heading and Cold Forging

Bar and Wire ASTM A516/A516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate-

and lower- temperature service ASTM A525 Standard Specifications for General Requirements for Steel Sheet,

Zinc-Coated (Galvanized) By the Hot-Dip Process ASTM A536 Ductile iron Castings ASTM A553/A553M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and

Tempered 8 and 9 percent Nickel ASTM A577/A577M Specification for Ultrasonic Angle-beam Examination of Steel Plates ASTM A563 Carbon and Alloy Steel Nuts ASTM A572 Standard Specification for High-Strength Low- Alloy Columbium -

Vanadium Structural Steel


Resource Report 13

13.D-8

ASTM A615 Standard Specifications for Deformed and Plain Billet-Steel Bars for Concrete Reinforcement

ASTM A706 Standard Specification for Low-Alloy Steel Deformed Bars for Concrete Reinforcement

ASTM A722 Uncoated High-Strength Steel Bar for Prestressing Concrete ASTM A780 Practice for Repair of Damaged Hot-Dip Galvanized Coatings ASTM A786 Rolled Steel Floor Plates ASTM A992 Standard Specification for Steel for Structural Shapes for Use in

Building Framing ASTM B3 Soft or Annealed Copper Wire ASTM B8 Standard Specification for Concentric-Lay-Stranded Copper

Conductors, Hard, Medium-Hard, or Soft ASTM B117 Standard Practice for Operating Salt Spray (Fog) Apparatus ASTM B209 Standard Specification for Aluminum and Aluminum-Alloy Sheet and

Plate ASTM B496 Compact Round Concentric-Lay-Stranded Copper Conductors ASTM B633 Electro Deposited Coatings of Zinc on Iron and Steel ASTM C31 Making and Curing Concrete Test Specimens in the Field ASTM C33 Standard Specification for Concrete Aggregates ASTM C39 Standard Test Method for Compressive Strength of Cylindrical

Concrete Specimens ASTM C42 Standard Test Method for Obtaining and Testing Drilled Cores and

Sawed Beams of Concrete ASTM C94 ASTM C127 Standard Test Method for Specific Gravity and Absorption of Coarse

Aggregate ASTM C136 Sieve Analysis of Fine and Coarse Aggregates ASTM C140 Standard Test Methods for Sampling and Testing Concrete Masonry

Units and Related Units ASTM C143 Slump of Hydraulic Cement Concrete ASTM C150 Portland Cement ASTM C165 Test Method for Measuring Compressive Properties of Insulations ASTM C171 Sheet Materials for Curing Concrete ASTM C172 Sampling Freshly Mixed Concrete ASTM C177 Standard Test Method for Steady-State Heat Flux Measurements and

Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

ASTM C195 Standard Specification for Mineral Fiber Thermal Insulating Cement ASTM C217 Cold Applied. Tape Coatings for Exterior of Special Sections,

Connections, and Fittings for Buried/Submerged Steel Water Pipelines ASTM C260 Standard Specification for Air-Entraining Admixtures for Concrete ASTM C303 Test Method for Density of Preformed Block-Type Thermal Insulation ASTM C309 Liquid Membrane-Forming Compounds for Curing Concrete ASTM C343 Cellular Glass Block Insulation for Hot Surfaces to 600° F ASTM C392 Class I Mineral Wool Glass Block ASTM C449 Standard Specification for Mineral Fiber Hydraulic-Setting Thermal


Resource Report 13

13.D-9

Insulating and Finishing Cement ASTM C476 Specification for Grout ASTM C494 Standard Specification for Chemical Admixtures for Concrete ASTM C520 Standard Test Method for Density of Granular Loose Fill Insulations ASTM C535 Standard Test Method for Resistance to Degradation of Large-Size

Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine ASTM C552 Cellular Glass Block and Pipe-Thermal Insulation ASTM C533 Standard Specification for Calcium Silicate Block and Pipe Thermal

Insulation ASTM C549 Perlite Loose Fill insulation ASTM C591 Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation ASTM C618 Fly Ash and Raw or Calcined; Natural Pozzolan for Use as a Mineral

Admixture in Portland Cement Concrete ASTM C795 Standard Specification for Thermal insulation for Use in Contact with

Austenitic Stainless Steel ASTM C1107 Packaged Dry, Hydraulic-Cement Grout (Non-shrink) ASTM C1116 Fiber-Reinforced Concrete and Shotcrete ASTM D75 Standard Practice for Sampling Aggregates ASTM D226 Standard Specification for Asphalt-Saturated Organic Felt Used in

Roofing and Waterproofing ASTM D256 Impact Resistance of Plastics and Electrical Insulating Materials ASTM D422 Particle-Size Analysis of Soils ASTM D429 Standard Test Methods for Rubber Property - Adhesion to Rigid

Substrates ASTM D621 Compressive Properties of Rigid Cellular Plastics ASTM D659 Method for Evaluating Degree of Chalking of Exterior Paints ASTM D698 Test Method for Moisture-Density Relations of Soils and Soil-Aggregate

Mixtures Using 5.5 pound Rammer and 12 inch Drop ASTM D714/714 Standard Test Method for Evaluating Degree of Blistering of Paint ASTM D1140 Amount of Material in Soils Finer than the No. 200 Sieve ASTM D1186 Method fob Nondestructive Measurement of Dry Film Thickness of

Nonmagnetic Coatings Applied to a Ferrous Base ASTM D1535 Standard Method for Specifying Color by the Munsell System ASTM D1556 Density and Unit Weight of Soil in Place by the Sand-Cone Method ASTM D1557 Laboratory Compaction Characteristics of Soil Using Modified Effort

56,000 ft-lb/cu. ft. ASTM D1622 Density Apparent or Rigid Cellular Plastics ASTM D1654 Method for Evaluation of Painted or Coated Specimens Subjected to

Corrosive Environments ASTM D1692 Rate of Burning and/or Extent and Time of Burning of Cellular Plastics

Using a Specimen Supported by a Horizontal Screen ASTM D2000 Classification System for Rubber Products in Automotive Applications ASTM D2167 Density and Unit Weight of Soil in Place by the Rubber Balloon Method ASTM D2244 Test Method for Calculating of Color Differences from Instrumentally

Measured Color Coordinates ASTM D2487 Classification of Soils for Engineering Purposes (Unified Soil


Resource Report 13

13.D-10

Classification System) ASTM D2856 Open Cell Content of Rigid Cellular Plastics by the Air Pycnometer ASTM D2922 Density of Soil-Aggregate in Place by Nuclear Methods (Shallow Depth) ASTM D2937 Density of Soil in Place by the Drive-Cylinder Method ASTM D3017 Water Content of Soil and Rock in Place by Nuclear Methods (Shallow

Depth) ASTM D3487 Specification for Mineral Insulating Oil Used in Electrical Apparatus ASTM D3786 Standard Test Method for Hydraulic Bursting Strengths of Knitted

Goods and Non-woven Fabrics - Diaphragm Bursting Strength Tester Method

ASTM D4318 Liquid Limit, Plastic Limit, and Plasticity Index of Soils ASTM D4354 Standard Practice for Sampling Geosynthetics for Testing ASTM D4355 Standard Test Method for Deterioration of Geotextiles from Exposure to

Ultraviolet Light (Xenon-Arc Type Apparatus) ASTM D4533 Standard Test Method for Trapezoidal Tearing Strength of Geotextiles ASTM D4632 Standard Test Method for Grab Breaking Load and Elongation of

Geotextiles ASTM D4751 Standard Test Method for Determining Apparent Opening Size of a

Geotextile ASTM D4759 Standard Practice for Determining the Specification Conformance of

Geosynthetics ASTM D4945 Standard Test Method for High-Strain Dynamic Testing of Piles ASTM D5519 Standard Test Method for Particle Size Analysis of Natural and Man-

Made Riprap Materials ASTM D6092 Standard Practice for Specifying Standard Sizes of Stone for Erosion

Control ASTM D6684 Standard Specification for Materials and Manufacture of Articulating

Concrete Block (ACB) Revetment Systems ASTM E84 Test Method for Surface Burning Characteristics of Building Materials ASTM E96 Water Vapor Transmission of Materials Sheet Form ASTM E376 Standard Practice for Measuring Coating Thickness by Magnetic-Field

or Eddy-Current (Electromagnetic) Examination Methods ASTM F436 Hardened Steel Washers ASTM F1121–87 Standard Specification for International Shore Connections for Marine

Fire Applications (1993)

15.0 AWS AMERICAN WELDING SOCIETY SPECIFICATIONS

AWS A2.1 Welding Symbols AWS A2.4 Standard Symbols for Welding, Brazing, and Nondestructive

Examination AWS A3.0 Standard Welding Terms and Definitions AWS A4.2 Standard Procedure for Calibrating Magnetic Instruments to Measure

Delta Ferrite Content of Austenitic and Duplex Austenitic-Ferritic Stainless Steel Weld Metal

AWS A5.11 Specification for Nickel and Nickel Alloy Welding Electrodes for Shield


Resource Report 13

13.D-11

Metal Arc Welding AWS A5.14 Specification for Nickel and Nickel Alloy Bare Welding Electrodes and

Rod AWS D1.1 Structural Welding Code - Steel AWS D1.4 Structural Welding Code - Reinforcing Steel AWS D3.6 Specification for Underwater Welding

16.0 AWWA AMERICAN WATER WORKS ASSOCIATION

AWWA C200 AWWA Standard for Steel Water Pipe

17.0 CENELEC EUROPEAN COMMITTEE FOR ELECTRICAL STANDARDIZATION

18.0 CINI INSULATION FOR INDUSTRIES

19.0 CAA CLEAN AIR ACT

CAA Section 12 National Emission Standard for Hazardous Air Pollutants

20.0 CGA COMPRESSED GAS ASSOCIATION

CGA 341 Standard for Insulated Cargo Tank Specification for Nonflammable Cryogenic Liquids

21.0 CMAA CRANE MANUFACTURERS ASSOCIATION OF AMERICA

CMAA 70 Electric Overhead Traveling Cranes

22.0 29.0 CRSI CONCRETE REINFORCING STEEL INSTITUTE MANUAL OF PRACTICE

CRSI 63 Recommended Practice for Placing Reinforcing Bars CRSI 65 Recommended Practice for Placing Bar Supports, Specifications and

Nomenclature

23.0 CSA CSA AMERICA, INC

CSA for Class 1 Div 2 Shutdown System Adopting Latest Standards and Supporting Codes

24.0 EEMAC ELECTRICAL AND ELECTRONIC MANUFACTURERS OF CANADA

EEMAC G14-1 Procedure for Testing the Resistance of Metal-clad Switchgear Under


Resource Report 13

13.D-12

Condition of Arcing Due to an Internal Fault

25.0 EJMA STANDARDS OF THE EXPANSION JOINT MANUFACTURERS ASSOCIATION

26.0 EPA ENVIRONMENTAL PROTECTION AGENCY

EPA 40 CFR Part 61 Monitoring Requirements

27.0 FCI FLUID CONTROL INSTITUTE INC.

FCI 70-2 Control Valve Seat Leakage

28.0 FED-STD FEDERAL STANDARDS

FED-STD 595 (Rev B) Colors

29.0 FM FACTORY MUTUAL APPROVAL GUIDE

FM for Class 1 Div 2 (Shutdown System Adopting Latest Standards and Supporting Codes) 30.0 FS FEDERAL SPECIFICATIONS

FS FF-B-171 (Rev A; Am 1) Bearings, Ball, Annular (General Purpose) FS FF-B-185 (Basic; Am 4) Bearings, Roller, Cylindrical; and Bearings, Roller, Self

and Aligning FS RR-C-271 (Rev D) Chains and Attachments, Welded and Weldless FS RR-W-410 (Rev D Am 1) Wire Rope and Strand

31.0 GPA GAS PROCESSORS ASSOCIATION

GPA 2166 Obtaining Natural Gas Samples

32.0 GIIGNL LNG CUSTODY TRANSFER HANDBOOK

33.0 ICEA INSULATED CABLE ENGINEERS ASSOCIATION

ICEA S-68-516 (NEMA WC8) Ethylene-Propylene-Rubber-insulated Wire and Cable for the Transmission and Distribution of Electrical Energy

ICEA 5-73-532 (NEMA WC57) Control Cables


Resource Report 13

13.D-13

34.0 IEC INTERNATIONAL ELECTROTECHNICAL COMMISSION

IEC 751 Industrial Platinum Resistance Thermometer Sensors IEC 60534-1 Part 1 Industrial-Process Control Valve, Part 1: Control Valve Terminology and

General Conditions IEC 60534-2-1 Industrial-Process Control Valves, Part 2-1: Flow-Capacity, Sizing

Equations for Fluids Flow Under Installed Conditions IEC 60534-2-3 Industrial-Process Control Valves, Part 2-3: Flow Capacity, Test

Procedures IEC 60534-2-4 Industrial-Process Control Valves, Part 2: Flow Capacity, Section 4:

Inherent Flow Characteristics and Rangeability IEC 60534-3-1 Industrial-Process Control Valves, Part 3-1: Dimensions-Face-to-Face

Dimensions for Flanged, Two-Way, Globe-Type, Straight Pattern and Centre-Control Valves

IEC 60534-3-2 Industrial-Process Control Valves, Part 3-2: Dimensions-Face-to-Face Dimensions for Rotary Control Valves Except Butterfly Valves

IEC 60534-3-3 Industrial-Process Control Valves, Part 3: End-to-End Dimensions for Buttweld, Two-Way Globe-Type, Straight Pattern Control Valves

IEC 60534-4-4 Industrial-Process Control Valves, Part 4: Inspection Routine Testing IEC 60534-5 Industrial Process Control Valves, Part 5, Marking IEC 60534-6-1 Industrial Process Control Valves, Part 6, Mounting Details for

Attachment of Positioners to Control Valves, Section 1: Positioner Mounting on Linear Actuators

IEC 60534-8-2 Industrial Process Control Valves, Part 8, Noise Considerations, Section 2: Laboratory Measurement of Noise Generated by Hydrodynamic Flow through Control Valves

IEC 60534-8-3 Industrial Process Control Valves, Part 8, Noise Considerations, Section 8: Control Valves, Prediction of Noise Generated by Hydrodynamic Flow

IEC 615078 SIL 3 Functional Safety of Electrical/Electronic/Programmable Electronic Safety-Related Systems

IEC 61511 Safety Instrumented Systems for the Process Industry Sector

35.0 IEEE INSTITUTE OF ELECTRICAL AND ELECTRONIC ENGINEERS

IEEE 1202 Flame Testing of Cables for Use in Cable Tray in Industrial and Commercial Occupancies

IEEE 383 Type Test of Class 1E Electric Cables, Field Splices, and Connections for Nuclear Power Generating Stations

IEEE 841 Standard for Petroleum and Chemical Industry - Severe Duty Totally Enclosed Fan Cooled (TEFC) Squirrel Cage Induction Motors - Up to and Including 500 Horsepower

IEEE C2 National Electrical Safety Code IEEE C12.1 Code for Electrical Metering IEEE C37.04 Standard Rating Structure for AC High-Voltage Circuit Breakers Rated

on a Symmetrical Current Basis


Resource Report 13

13.D-14

IEEE C37.06 AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis -- Preferred Ratings and Related Required Capabilities

IEEE C37.13 Low-Voltage AC Power Circuit Breakers Used in Enclosures IEEE C37.20.1 Metal-Enclosed Low-Voltage Power Circuit-Breaker Switchgear IEEE C37.20.2 Standard for Metal-Clad and Station-Type Cubicle Switchgear IEEE C37.23 Standard for Metal-Enclosed Bus and Calculating Losses in Isolated-

Phase Bus IEEE C37.40 Service Conditions and Definitions for High-Voltage Fuses, Distribution

Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories

IEEE C37.60 Standard for Overhead, Pad-Mounted, Dry Vault, and Submersible Automatic Circuit Reclosers and Fault Interrupters for Alternating Current Systems Up to 38 kV

IEEE C57.104 Guide for the Interpretation of Gases Generated in Oil Immersed Transformers (ANSI)

IEEE C57.111 Guide for Acceptance of Silicone Insulating Fluid and Its Maintenance in Transformers

IEEE C57.12.00 Standard General Requirements for Liquid-Immersed Distribution, Power, and Regulating Transformers

IEEE C57.12.13 Liquid-Filled Transformers Used In Unit installations Including Unit Substations Conformance Standard

IEEE C57.12.80 Standard Terminology for Power and Distribution Transformers (ANSI) IEEE C57.12.90 Standard Test Code for Liquid-Immersed Distribution, Power, and

Regulating Transformers; and Guide for Short-Circuit Testing of Distribution and Power Transformers (ANSI)

IEEE C57.13 Standard Requirements for Instrument Transformers IEEE C57.13.1 Field Testing of Relaying Current Transformers IEEE Std. 1 General Principles for Temperature Limits in the Rating of Electrical

Equipment and for the Evaluation of Electrical Insulation IEEE Std. 80 AC Substation Grounding IEEE Std 142 Grounding of Industrial and Commercial Power Systems (Lightning

Protection) IEEE Std. 519 Recommended Practices and Requirements for Harmonic Control in

Electrical Power Systems IEEE Std. 837 Qualifying Permanent Connections Used in Substation Grounding IEEE Std. 998 Guide for Direct Lightning Strike Shielding of Substations

36.0 ISA THE INSTRUMENTATION, SYSTEMS AND AUTOMATION SOCIETY

ISA 20 Specification Forms for Process, Measurement and Control Instruments, Primary Elements, and Control Valves

ISA 75.01 Flow Equations for Sizing Control Valves ISA 75.03 Face-to-Face Dimensions for Integral Flanged Globe-Style Control

Valve Bodies (ANSI Classes 125, 150, 250, 300 and 600) ISA 75.04 Face-to-Face Dimensions for Flangeless Control Valves (ANSI Classes

150, 300 and 600)


Resource Report 13

13.D-15

ISA 75.08.04 Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (ANSI Classes 4500)

ISA 75.08.07 Face-to-Face Dimensions for Separable Flanged Globe-Style Control Valves (ANSI Classes 150, 300 and 600)

ISA 75.15 Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500 and 2500)

ISA 75.16 Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (ANSI Classes 900, 1500 and 2500)

ISA 75.17 Control Valve Aerodynamic Noise Prediction ISA 75.19.01 Hydrostatic Testing of Control Valves ISA 75.22 Face-to-Centerline Dimensions for Flanged Globe-Style Angle Control

Valve Bodies (ANSI Classes 150, 300 and 600) ISA 75.25 Test Procedure for Control Valve Response Measurement from Step

Inputs ISA S5.1 Instrumentation Symbols and Identification ISA S5.3 Graphics Symbols for Distributed Control/Shared Display

Instrumentation, Logic and Computer Systems ISA S84 Shutdown System Adopting Latest Standards and Supporting Codes ISA S91 Shutdown System Adopting Latest Standards and Supporting Codes ISA-RP-12.1 Electrical Instruments in Hazardous Areas ISA-RP-12.4 Instrument Purging for Reduction of Hazardous Area Classification

37.0 ISO INTERNATIONAL ORGANIZATION FOR STANDARDIZATION

ISO 3171:1988 Petroleum Liquids Automatic Pipeline Sampling ISO 5752 Metal Valve for Use in Flanged Pipe Systems – Face-to-Face and

Center-to-Face Dimensions ISO 8943 Refrigerating Light Hydrocarbon Fluids

38.0 MNL 116 MANUAL FOR QUALITY CONTROL FOR PLANTS AND PRODUCTION OF PRECAST AND PRESTRESSED CONCRETE PRODUCTS

39.0 MS MILITARY SPECIFICATIONS

MS MIL-C-28546 (Rev A; Amt) Cranes, Overhead Traveling, Underhung, Electric Powered

MS MIL-V-173 (Rev C; Am 2, Notice 1) Varnish, Moisture-and-Fungus Resistant (for Treatment of Communications, Electronics, and Associated Equipment)

40.0 MSS MANUFACTURERS' STANDARDIZATION SOCIETY OF THE VALVE AND FITTING INDUSTRY

MSS SP-25 Standard Marking System for Valves, Fittings, Flanges and Unions MSS SP-53 Quality Standard for Steel Castings and Forgings for Valves, Flanges


Resource Report 13

13.D-16

and Fittings and Other Piping Components – Magnetic Particle Examination Method

MSS SP-54 Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components – Radiographic Examination Method

MSS SP-55 Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components – Visual Method for Evaluation of Surface Irregularities

MSS SP-67 Butterfly Valves MSS SP-68 High Pressure – Offset Seat Butterfly Valves MSS SP-93 Quality Standard for Steel Castings and Forgings for Valves, Flanges

and Fittings and Other Piping Components – Liquid Penetrant Examination Method

MSS SP-94 Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components – Ultrasonic Examination Method

41.0 NACE NATIONAL ASSOCIATION OF CORROSION ENGINEERS

NACE MR-01-75 Sulfide Stress Cracking Resistant Metallic Materials for Oil Field Equipment

NACE RP0169 Control of External Corrosion on Underground or Submerged Metallic Piping Systems

NACE RP0187 Design Consideration for Corrosion Control of Reinforcing Steel in Concrete Structure

NACE RP0591 Coatings for Concrete Surfaces in Non-Immersion and Atmospheric Service

NACE TM-0170 Visual Standard for Surfaces of New Steel Air-blast Cleaned with Abrasive

42.0 NACE/INTERNATIONAL NATIONAL ASSOCIATION OF CORROSION ENGINEERS

RP-0188 Discontinuity (Holiday) Testing of New Protective Coatings on Conductive Substrates

PIP Coatings Process Industry Practices PIP CTCE-1000 External Coating Systems Selection Criteria PIP CTSE-1000 Application of External Coatings

43.0 NEMA NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION

NEMA 250 Enclosures for Electric Equipment (1000 Volts maximum) NEMA BU 1 Busways NEMA KS 1 Enclosed and Miscellaneous Distribution Equipment Switched (600

Volts Maximum)


Resource Report 13

13.D-17

NEMA ICS 1 Industrial Control and Systems General Requirements NEMA ICS 2 industrial Control and Systems Controllers, Contactors, and Overload

Relays Rated Not More Than 2000 Volts AC or 750 Volts DC NEMA ICS 3 Industrial Control and Systems Factory Built assemblies NEMA ICS 4 Industrial Control and Systems Terminal Blocks NEMA ICS 6 Industrial Control and Systems Enclosures NEMA MG 1 Motors and Generators NEMA SG-5 Power Switchgear assemblies NEMA ST 1 Specialty Transformers (Except General Purpose Type) NEMA WC26 Wire and Cable Packaging

44.0 51.0 NFPA NATIONAL FIRE PREVENTION ASSOCIATION

NFPA 10 Portable Fire Extinguishers NFPA 15 Standard for Water Spray Fixed Systems for Fire Protection NFPA 14 Standard for the Installation of Standpipe and Hose Systems NFPA 17 Standard for Dry Chemical Extinguishing System NFPA 20 Firewater Pumps NFPA 24 Private Firewater Systems NFPA 30 Flammable Liquids Code NFPA 51B Fire Prevention in Use of Cutting and Welding Processes, 1994 NFPA 59A Standard for the Production, Storage and Handling of LNG, 1994 NFPA 70 National Electric Code (NEC) NFPA 72 Fire Alarm Code NFPA 78 Lightning Protection Code NFPA 101 Life Safety Code NFPA 251 Fire Tests of Building Construction and Materials, 1990 NFPA 255 Method of Test of Surface Burning Characteristics of Building Materials NFPA 496 Standard For Purged and Pressurized Enclosures For Electrical

Equipment in Hazardous Areas

45.0 OCIMF OIL COMPANIES INTERNATIONAL MARINE FORUM

Design and Construction Specification for Marine Loading Arms Fire Protection for Marine Terminals Prediction of Wind and Current Loads on VLCCs Safety Guide for Terminals Handling Ships Carrying Liquefied Gases in Bulk Prediction of Wind loads on Large Liquefied Gas Carriers International Safety Guide for Oil Tankers and Terminals

46.0 OCMA FSV.1 FIRE SAFE CONSTRUCTION FOR BALL VALVES


Resource Report 13

13.D-18

47.0 OSHA OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION

OSHA 1910.95 Occupational Noise Exposure Regulation OSHA 29 CFR1910. 106

Flammable Liquids

OSHA 29 CFR1910. 165

Fire Alarm Systems

48.0 PCI PRECAST/PRESTRESSED CONCRETE INSTITUTE

MNL-120-99 Precast and Prestressed Concrete

49.0 PIP PROCESS INDUSTRY PRACTICES, PIPING, LATEST EDITION

PIP CTCE-1000 External Coating Systems Selection Criteria PIP CTSE-1000 Application of External Coatings

50.0 SIGTTO SOCIETY OF INTERNATIONAL GAS TANKER & TERMINAL OPERATORS

A Guide to Contingency Planning for Marine Terminals Handling Liquefied Gases in Bulk Guidelines for Hazard Analysis as an Aid to Management of Safe Operations Ship/Shore Interface Communications Recommendations and Guidelines for Linked Ship/Shore Emergency Shut-Down of Liquefied Gas Cargo Transfer Guidelines for the Alleviation of Excessive Surge Pressures on ESD Liquefied Gas Handling Principles on Ships and in Terminals Fire Protection for Marine Terminals Prediction of Wind Loads on Large Liquefied Gas Carriers, 1995 SIGTTO/OCIMF Listing of Design Guidelines for Liquefied Gas Terminals

51.0 SSPC STEEL STRUCTURE PAINTING COUNCIL STANDARDS

SSPC - AB1 Mineral and Slag Abrasives SSPC PA1 Shop, Field and Maintenance Painting SSPC - PA-2 Measurement of Dry Coasting Thickness with Magnetic Gages SSPC - SP-1 Solvent Cleaning SSPC - SP-2 Hand Tool Cleaning SSPC - SP-3 Power Tool Cleaning SSPC - SP-5 (NACE No.1)

White Metal Blast Cleaning

SSPC - SP-6 (NACE No. 3)

Commercial Blast Cleaning

SSPC - SP-7 (NACE No. 4)

Brush-off Blast Cleaning

SSPC - SP-10(NACE Near-White Blast Cleaning


Resource Report 13

13.D-19

No. 2) SSPC SP-11 Power Tool Cleaning to Bare Metal SSPC-VIS 1&3 Pictorial Surface Preparation Standards for Abrasive Blast and

Power/Hand Tool Cleaned Steel

52.0 TEMA TUBULAR EXCHANGER MANUFACTURER ASSOCIATION

Standards for Finned Tube Type Exchangers (Vaporizers)

53.0 TUV APPROVAL TO LEVEL AK-6 SHUTDOWN SYSTEM ADOPTING LATEST STANDARDS AND SUPPORTING CODES

54.0 UBC-1997 UNIFORM BUILDING CODE (SEISMIC) OR FEMA PUBLICATION 368 - NEHRP 2000, USE IN CONJUNCTION WITH 14

55.0 UFC UNIFORM FIRE CODE

56.0 UL UNDERWRITERS LABORATORIES, INC.

UL 05 Fire Resistance Directory UL 50 UL Standard for Safety - Cabinets and Boxes UL 508 Shutdown System Adopting Latest Standards and Supporting Codes UL 674 Electric Motors and Generators for Use in Hazardous (Classified)

Locations UL 845 Standard for Motor Control Centers UL 857 Busways and associated Fitting2s UL 1072 Medium-Voltage Power Cables UL 1277 Standard for Safety for Electrical Power and Control Tray Cables with

Optional Optical-Fiber Members UL 1558 Standard for Safety Metal-Enclosed Low-Voltage Power Circuit Breaker

Switchgear UL 1569 Metal-Clad Cables

57.0 AIDS TO NAVIGATION (ATONS)

References 1. United States Coast Guard COMDTINST M16500.1C Aids to Navigation Positioning Manual COMDTINST M16500.3A Aids to Navigation Technical Manual COMDTINST M16500.7 Aids to Navigation Administration Manual COMDTINST M16500.21 Aids to Navigation Seamanship Manual. COMDTINST M16510.2A Aids to Navigation Visual Signal Design Manual


Resource Report 13

13.D-20

2. United States of America Code of Federal Regulations, Title 33, Navigation and Navigable Waters, Chapter 1 - Coast Guard, Department of Homeland Security, Part 62 - United States Aids to Navigation System 3. ASTM D25 Standard Specification for Round Timber Piles 4. AWPA C3 Standard Specification for CCA Treatment

58.0 STEEL SHEET PILING

References Design of Sheet Pile Walls (Technical Engineering and Design Guides as Adapted from the U.S. Corps of Engineers, No. 15) D3.6 Specification for Underwater Welding

59.0 CERTAIN OTHER CODES, STANDARDS, SPECIFICATIONS AND GUIDELINES

Permanent International association of Navigation Congresses "Guidelines for the Design of Fender Systems", 2002 46 CFR Part 154, Safety Standards for Self-propelled Vessels Carrying Bulk Liquefied Gases 49 CFR Part 191, Transportation of Natural and Other Gas by Pipeline; Annual Reports, Incident Reports, and Safety-Related Condition Reports 49 CFR Part 192, Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards 49 CFR Part 193, Liquefied Natural Gas Facilities: Federal Safety Standards 49 CFR Part 195, Transportation of Hazardous Liquids by Pipeline 49 CFR Part 199, Drug and Alcohol Testing. U.S. Army Corps of Engineers. 2002. Coastal Engineering Manual. Engineer Manual 1110-2-1100, U.S. Army Corps of Engineers, Washington, D.C. (in 6 Volumes). U.S. Army Corps of Engineers. 1995. Designs of Coastal Revetments, Seawalls, and Bulkheads. Engineer Manual 1110-2-1614, U.S. Army Corps of Engineers, Washington, D.C., misc. paginated. Center for Civil Engineering Research and Codes. 1995. Manual on the Use of Rock in Hydraulic Engineering. CUR/RWS Report 169, A.A. Balkema Publishers, Brookfield, VT.

Weaver's Cove Energy Offshore Design Codes and Standards

Documents

Transcript of Weaver's Cove Energy Offshore Design Codes and Standards