WCDMA RNC Engineering Design Guide 20050929 a 1.0
-
Upload
bayu-pramadiyan -
Category
Documents
-
view
82 -
download
5
Transcript of WCDMA RNC Engineering Design Guide 20050929 a 1.0
Document code Product
name WCDMA-RNC
Intended audience Internal engineers Product
version
Compilation department
UMTS product department
Document version V1.00
WCDMA-RNC Engineering Design Guide
Drafted by Date Reviewed
by Date
Reviewed by Date
Approved by Date
Huawei Technologies Co., Ltd.
All Rights Reserved
Revision Record
Date Version Description Writer
WCDMA-RNC Engineering Design Guide
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
Table of Contents
Chapter 1 Brief Introduction....................................................................................................... 1
1.1 Purpose................................................................................................................................. 1
1.2 Intended Audience................................................................................................................ 1
1.3 Application Occasion ............................................................................................................ 1
1.4 Operation Specifications....................................................................................................... 1
Chapter 2 Work for Engineering Design .................................................................................... 2
2.1Engineering Design Documents ............................................................................................ 3
2.2Engineering Design Document Execution ............................................................................. 4 2.2.1Engineering Overview ................................................................................................. 4 2.2.2System Networking Diagram....................................................................................... 5 2.2.3Engineering Interface .................................................................................................. 6 2.2.4Layout Diagram of Equipment Room.......................................................................... 7 2.2.5Cabling Diagram of Equipment Room......................................................................... 8 2.2.6GPS Antenna Installation Drawing.............................................................................. 9 2.2.7Cabinet Card Layout ................................................................................................... 9 2.2.8Alarm Cable Connection Table ................................................................................. 10 2.2.9PDF Unit Distribution Drawing .................................................................................. 10 2.2.10Iub Trunk Distribution Table .................................................................................... 11 2.2.11Iub Interface Fiber Allocation Table ........................................................................ 11 2.2.12External Interface STM-1 Allocation Table ............................................................. 12 2.2.13Internal Interface STM-1 Allocation Table............................................................... 12 2.2.14OMC System Networking Diagram ......................................................................... 12
WCDMA-RNC Engineering Design Guide
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
Keyword
engineering design
Summary
The document describes the contents of WCDMA-RNC engineering design document and
related execution demands.
Reference
[1] Package of Documents for BSC6800 Products of Huawei
[2] WCDMA-RAN Networking Design Guide
WCDMA-RNC Engineering Design Guide
Chapter 1 Brief Introduction
1.1 Purpose
The WCDMA-RNC Engineering Design Guide is written for engineers of Huawei to finish WCDMA RNC system engineering design work.
1.2 Intended Audience
1. Technical supporters
2. Developers
Note:
Engineering design work should be completed by the personnel who have product bases or by the guide of the personnel who have product bases. For some basic knowledge, there are no detailed descriptions in this guide.
1.3 Application Occasion
Before a site deployment, the system design contents should be completed. The main operators are wireless system design engineers and site deployment engineers.
1.4 Operation Specifications
(1) Execute according to the templates offered by Huawei strictly;
(2) The designs should be precise and detailed;
(3) Accord with related operation specifications of Huawei.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
Chapter 2 Work for Engineering Design
For engineering design, the items in China are completed by the mobile carrier delegates them to the provincial design institute. And XX Project Technical Proposals is exported. For items outside China, the Marketing of Huawei completes the system design according to the suggestions of market technology team and technical support. The XX Project Technical proposals and the related logic networking diagram should be exported too; and then the Customer Service carries out the site survey. Additionally, the Site Survey Report is exported. According to Contract List BOQ, XX Project Technical Proposals and Site Survey Report, technical support engineering design team completes concrete engineering design documents. The networking diagrams in the engineering design documents should be reviewed by technical support.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
The purpose of the system design's whole tache is to offer site engineering implementation guide. So the engineering design documents should be exported finally. The emphasis of this guide is to introduce how to complete the execution of engineering design documents.
2.1Engineering Design Documents
Chapter Document name Document format
Completed by
Chapter 1 Engineering Overview
Engineering Overview
DOC Engineering design engineers
Chapter 2 System Networking
System Networking Diagram
VISIO Engineering design Engineers
Chapter 3 Engineering Interface
Engineering Interface
DOC Engineering Survey Engineers
Floor Plan AUTOCAD Engineering Survey Engineers
Machine Room Cabling Diagram
AUTOCAD Engineering Survey Engineers
Chapter 4 Engineering Drawing
GPS Installation Drawing
AUTOCAD Engineering Survey Engineers
Cabinet Card Layout
DOC Engineering design engineers
Chapter 5 Hardware Configuration
PDF unit distribution list
DOC Engineering design engineers
Alarm Cable Connection Table
DOC Engineering design engineers
Iub Trunk Distribution Table
DOC Engineering design engineers
Iub Fiber Allocation Table
DOC Engineering design engineers
Internal STM-1 Allocation Table
DOC Engineering design engineers
Chapter 6 External Cable Connection
External STM-1 Allocation Table
DOC Engineering design engineers
OMC System Overview
DOC Engineering design engineers
Chapter 7 OMC System
OMC System Networking Diagram
VISIO Engineering design engineers
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
2.2Engineering Design Document Execution
2.2.1Engineering Overview
1. Description
The function of this document is to make engineering personnel know the basic information of engineering. The information includes: engineering information, subscriber information and equipment information. At the same time, you should supplement the basic demands of engineering.
2. Template
Engineering Information
Office name
Engineering type
Equipment composing
Before construction
System capacity
Equipment composing
After construction
System capacity
Subscriber information
Subscriber name
Postal code
Contact person
Contact telephone
Fax
Design information
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
Telephone Survey
personnel
Telephone Design
personnel
3. Execution Demand
Use WORD and fill in the table in detail. You can get the information from local offices, survey engineers and market personnel.
4. Precautions
Assure the correctness of information.
2.2.2System Networking Diagram
1. Description
Usually, MAEKETING and the documents offered by operator at the time of pre-sales communion are used. The logical connections of equipment are introduced. The purpose is to make engineers know about the general view of whole networking, including the equipment owing to the cooperation of partner/competitor.
2. Template
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
3. Execution Demand
You can use VISIO or AUTOCAD to execute. Describe the signaling trend of equipment, IP networking and service trend in detail.
4. Precautions
The networking drawing must be approved by technical support before writing out the engineering design document.
2.2.3Engineering Interface
1. Description
The document is the engineering interface document drawn by site survey personnel according to site situations. By this document, we can know which should be done by Huawei and which need the cooperation of operator.
2. Template
D C p o w e r d is t rib u t io n
u n it D D F /O D F
D C p o w e r d is t rib u t io n
ra c k
M a in sA C p o e w e r d is t rib u t io n
b o x
G ro u n d in g b a r
U P Sin ve rte r
B A M te rm in a l/S e rve r/L A N /R o u te r
re c t ifie r u n it
B a t te ry
E q u ip m e n t t o b e p ro vid e d a n d in s t a l le d b y t h e s u p p l ie r
E q u ip m e n t to b e p ro vid e d a n d in s t a lle d b y t h e u s e rC a b le s to b e p ro vid e d a n d la id b y t h e u s e r
C a b le s t o b e p ro vid e d a n d la id b y th e s u p p lie rC o n n e c t o rs to b e p ro vid e d a n d c o n n e c t e d b y t h e s u p p lie r
C o n n e c to rs t o b e p ro vid e d a n d c o n n e c te d b y t h e u s e r
A la rm b o x
C a b lin g la d d e r
N e tw o rk c a b in e t
RNCc a b in e t
A C p o w e r d is t rib u t io n
u n itE le c t ric g e n e ra to r
Tra ns m is s io n D D F
S D H
3. Execution Demand
Use word templates. The real lines show the engineering related parts of Huawei. And the dashed lines show the parts needing the cooperation of operators.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
4. Precautions
For the concrete engineering interface division, you should communicate with the operator in advance. The purpose is to avoid a dispute.
2.2.4Layout Diagram of Equipment Room
1. Description
This drawing is offered by survey engineers too. The function is that site engineers can know the concrete placement locations of equipment.
2. Template
3. Execution Demand
Offer the AUTOCAD mode. Use A4 standard engineering drawings offered by Huawei. Mark up the distance between cabinets in detail.
4. Precautions
The floor plan should be confirmed by the signature of operator.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
2.2.5Cabling Diagram of Equipment Room
1. Description
The function is to offer a cabling diagram of transmission cables during the project and guide site engineering installations.
2. Template
3. Execution Demand
For this document, you need to offer the AUTOCAD mode. Use A4 standard engineering drawings offered by Huawei. Show the transmission cable trends from equipment to DDF and PDF clearly. At the same time, you should mark clearly it is upward wiring or downward wiring. Introduce the detailed trends of power cables, trunk cables, signal cables and network cables.
4. Precautions
Describe clearly about the height of machine room, floor, with or without floor board, upward and downward wirings, new or expansion equipment.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
2.2.6GPS Antenna Installation Drawing
1. Description
During projects, if GPS antennas are necessary, survey engineers execute this drawing to guide the GPS antenna installation.
2. Template
3. Execution Demand
Offer the AUTOCAD mode. Use A4 standard engineering drawings offered by Huawei. Mark up the equipment position and cable route clearly.
4. Precautions
Mark up the position of outdoor grounding bar.
2.2.7Cabinet Card Layout
1. Description
Board types and amount are gotten from quotation. According to the card position configuration principle, arrange the board position reasonably.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
2. Demand
Execute using the stated template. You must accord with the card position configuration principle.
2.2.8Alarm Cable Connection Table
1. Description
If RNC has the alarm box connection, fill in the table.
2. Execution Demand
Fill in the stated table. Mark up the alarm cable connection port clearly.
2.2.9PDF Unit Distribution Drawing
1. Description
The unit distribution drawing of PDF describes detailed situations of existing network power cabinet.
2. Template
A01 A02 A03 A04 A05 A06 A07 A08 A09 A10
-48V1
B01 B02 B03 B04 B05 B06 B07 B08 B09 B10
-48V2
A11 A12 A13 A14 A15 A16 A17 A18 A19 A20
-48V1
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
B11 B12 B13 B14 B15 B16 B17 B18 B19 B20
-48V2
A21 A22 A23 A24 A25 A26 A27 A28 A29 A30
-48V1
B21 B22 B23 B24 B25 B26 B27 B28 B29 B30
-48V2
3. Execution Demand
Use the WORD template. Describe current demands and the used power switches in detail.
2.2.10Iub Trunk Distribution Table
1. Description
The table marks up the distribution of Iub interface trunk.
2. Execution Demand
Fill in according to the stated WORD template. Mark up the every trunk's corresponding DDF rack port and the peer NodeB name clearly.
2.2.11Iub Interface Fiber Allocation Table
1. Description
If the Iub interface uses fiber to connect, fill in this table.
2. Execution Demand
Fill in according to the stated WORD template. Mark up every tail fiber's corresponding ODF port and the peer NodeB name clearly.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
2.2.12External Interface STM-1 Allocation Table
1. Description
The table describes the distribution of external STM-1.
2. Execution Demand
Fill in according to the stated template. Be clear about every port corresponding ODF rack position and the opposite equipment name. For one interface, if there are two pairs of fiber, they should distribute on different boards in reason.
2.2.13Internal Interface STM-1 Allocation Table
1. Description
The table describes internal fiber allocations.
2. Execution Demand
Fill in according to the stated template. The two pairs of fiber to the same frame should distribute on different boards in reason.
2.2.14OMC System Networking Diagram
1. Description
It describes the OMC networking diagram.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page
WCDMA-RNC Engineering Design Guide
2. Template
3. Execution Demand
Execute by using AUTOCAD or VISIO. In the front of the table, you can add the LanSwitch port description used by the equipment side. You can mark up different port functions and the VLAN usage situations by different colors.
Huawei Technologies Co., Ltd. Huawei Proprietary , All Rights Reserved. Page