Water Supply - Raw Water Intake
description
Transcript of Water Supply - Raw Water Intake
-
INT
Wat
er M
anag
emen
tW
ilo C
atal
ogue
Wat
er S
uppl
y
Raw
Wat
er In
take
201
4/20
15
Pioneering for You
WILO SENortkirchenstrae 100D-44263 DortmundGermanyT +49 231 4102-0F +49 231 [email protected]
More contact details at www.wilo.com
2149859/500/1405/EN/MP
Catalogue Water Management 2014/2015
Water Supply Raw Water Intake
Submersible pumps, systems and accessories for raw water intake, water distribution, water treatment, desalination and agriculture
Pioneering for You
-
At Wilo, we focus on your water management project. For your sewage system, wastewater treatment plant or water distribution system, our expert team develops customized solutions. For these, we permanently test and refine new technologies simplifying your job and ensuring more planning certainty. How can we support you?
www.wilo.com
Developing techno-logies that make your job easier,thats what I callPioneering for You.
Wilo-EMU FA Wilo-EMU KMWilo-EMU Megaprop
Dr.-Ing. Markus Beukenberg, Chief Technical Officer, WILO SE Dortmund/Germany
Wilo-SCP Wilo-Sub TWU 3-HS-I Wilo TWU 3-HS-E-CP
Enhanced output due to increased speed (up to 8,400 l/min.) have given the Wilo-Sub TWU 3-HS-I and the Wilo-Sub TWU 3-HS-E-CP the nickname the fast one. The pumps ensure constant high pressure thanks to an integrated or external frequency converter. And all that in 3 inches, which keeps removal and installation costs low. With flexible installation vertically or horizontally, youre sure to be completely convinced.
www.wilo.com
High speed, high output. Thats what I call power.The Wilo solution for raw water intake.
Check also:
productfind
er.wilo.com
-
3Contents
Subm
ersi
ble
pum
psW
ater
-sup
ply
units
Dry
mou
nted
pum
psAc
cess
orie
sCo
nsul
ting
guid
e
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
General notes and abbreviations 8
Submersible pumps 11
Wilo-Sub TWUWilo-Sub TWI Wilo-EMU 6"24"Wilo-EMU polder pumps
Water-supply units 409
Wilo-Sub TWU Plug & Pump systemsWilo-Sub TWI Plug & Pump systems
Dry mounted pumps 416
Norm pumpsPumps with axially split housingAxial pumps
Accessories 419
Electrical accessoriesMechanical accessories
Consulting guide 432
-
4 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Water Supply Raw Water IntakeContents
Submersible pumps
3" and 4" series Series overview 11
Wilo-Sub TWU 3 16*)
Wilo-Sub TWU 3--HS 18*)
Wilo-Sub TWU 4 20*)
Wilo-Sub TWU 4--GT 22*)
Wilo-Sub TWU 4--QC 24*)
Wilo-Sub TWI 4 26*)
Wilo-Sub TWI 5/SE 28*)
6" series Series overview 13
Wilo-Sub TWU 6 30
Wilo-Sub TWI 6 49
Wilo-EMU 6" 82
8" series Series overview 14
Wilo-Sub TWU 8 129
Wilo-Sub TWI 8 141
Wilo-EMU 8" 164
10"...24" series Series overview 15
Wilo-Sub TWI 10 277
Wilo-EMU 10"...24" 307
Wilo-EMU polder pumps 388
Water-supply units
Systems Series overview 409
Wilo-Sub TWU 3 Plug & Pump systems 410*)
Wilo-Sub TWU 4 Plug & Pump systems 412*)
Wilo-Sub TWI 5/SE Plug & Pump systems 414*)
Dry mounted pumps
Norm pumps Series overview 416
Wilo-CronoNorm-NL 416*)
Wilo-VeroNorm-NPG 416*)
Axially split case pumps Wilo-SCP 417*)
Axial pumps Vertical turbine pumps 418*)
Accessories Electrical accessories 419
Mechanical accessories 425
*) see Wilo online catalogue
-
5Water Supply Raw Water IntakeContents
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Subm
ersi
ble
pum
psW
ater
-sup
ply
units
Dry
mou
nted
pum
psAc
cess
orie
sPl
anni
ng g
uide
Consulting guide
Fields of application, principle of operation and standards 432
Water extraction and supply 433
Well-sinking 436
Offshore applications 437
Material selection by water analysis 439
General cable-laying principles 440
Cable-laying Wilo-EMU series 441
Cable-laying Wilo-Sub series 442
-
6 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Programme overview and fields of applications
Three other catalogues are available for building services applications.
Catalogue Water Supply
Water Supply / Heating, Air-conditioning, Cooling
Glanded in-line pumps
Glanded monobloc pumps
Glanded norm pumps
Axially split case pumps
Condensate lifting units
High-pressure multistage centrifugal pumps
Pumps for fire extinguishing and sprinkler systems
BoostingSingle-pump systems
Multi-pump systems
Raw Water Intake
Submersible pumps
Polder pumps (Bottom intake pumps)
Vertical turbine pumps
Catalogue Drainage and Sewage
Wastewater Collection and Transport
Sewage lifting unit
Pumps stations
Submersible sewage pumps with macerator
Solids separation systems (EMUport)
Wastewater Transport and Dewatering(Stock pumps)
Submersible drainage pumps
Self-priming drainage pumps
Submersible sewage pumps
Wastewater Transport and Dewatering (Order-specific production)
Submersible sewage pumps
Axial submersible pumps (pipe sump pumps)
Wastewater Treatment
Submersible mixer
Solids diffuser
Ventilation systems
Submersible mixers for special and industrial applications (MUD mixers)
Recirculation pumps
Axial submersible pumps (pipe sump pumps)
Jet cleaner
Key: Fields of application:
Applicable- Not applicable1) Local prescriptions and directives must be observed
Heating Rainwater utilisation
Secondary hot water Water distribution/boosting
Air-conditioning Fire fighting1)
Cooling/Air-conditioning Clean water treatment
-
7Programme overview and fields of applications
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Troc
kenl
ufe
rpum
pen
Bloc
kpum
pen
Nor
mpu
mpe
nPu
mpe
n m
it ax
ial g
etei
ltem
Ge
hus
eM
ehrs
tufig
e H
ochd
ruck
-Kr
eise
lpum
pen
Main field of application
1) 1) 1)
Fields of application:
Raw water intake Wastewater collection and transport
Desalination Wastewater treatment
Professional irrigation/agriculture Dewatering (incl. Flood Control)
Energy/Leisure/ServiceSpecial applications Industrial process
-
8 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
General notes and abbreviations
Abbrevia-tion
Meaning
1~ 1-phase current3~ 3-phase current-A Float switch attachedD Direct activationDI Leakage detectionDi Inside diameterDi min. Minimum inside diameterDM Three-phase motor, 3~DN Nominal diameter of the flange connection EBM Individual run signalEM Single-phase motor, 1~ESM Individual fault signalGRD/GLRD Mechanical sealF Thrust in newtons (N) (for submersible mixers)H, Hmax Delivery headHA Suction head; inlet floor to ground levelHB Installation depth to inlet floorHN Site altitude above MSL (mean sea level)HG Groundwater level to MSL (mean sea level)IA Starting currentIN Nominal current; current at P2Inst. Installation: H = horizontal, V = vertical
@Supply availability (L = stock article, C = available in 2 weeks, K = available in 4 weeks, A = available on re-quest)
P1 Power consumption (power supplied from the network)P1.1 Power consumption at the duty pointP2 (PN) Nominal motor powerPN Pressure class in bar (e.g. PN10 = suitable up to 10 bar)
PTC Positive temperature coefficient (PTC thermistor sen-sor)
PT 100 Platinum temperature sensor with a resistance value of 100 at 0 CQ (=) Volume flow-S Float switch attachedSBM Run signal or collective run signalSSM Fault signal or collective fault signal
WSKThermal winding contacts (in motor for monitoring the winding temperature, full motor protection through additional tripping unit)
Y/ Star-delta switching
; Operating mode of double pumps: Individual operation of the respective duty pump
< Operating mode of double pumps: Parallel operation of both pumps
Number of poles of electric motors: 2-pole motor = ap-prox. 2900 rpm at 50 Hz
Number of poles of electric motors: 4-pole motor = ap-prox. 1450 rpm at 50 Hz
Number of poles of electric motors: 6-pole motor = ap-prox. 950 rpm at 50 Hz
Material Meaning AISI1.0570 Steel S355J2G3 A1061.4021 Chromium steel X20Cr13 4201.4057 Chromium steel X17CrNi16-2 4311.4112 Chromium steel X90CrMoV18 440B1.4122 Chromium steel X39CrMo17-11.4301 Chromium-nickel steel X5CrNi18-10 3041.4305 Chromium-nickel steel X8CrNiS18-9 3031.4306 Chromium-nickel steel X2CrNi19-11 304L
1.4308 Chromium-nickel steel GX5CrNi19-10 304 CF8
1.4401 Chromium-nickel-molybdenum steel X5CrNiMo17-12-2 316
1.4404 Chromium-nickel-molybdenum steel X2CrNiMo17-12-2 316L
1.4408 Chromium-nickel-molybdenum steel GX5CrNiMo19-11-2 316
1.4460 Chromium-nickel-molybdenum steel X3CrNiMoN 27-5-2 329
1.4462 Chromium-nickel-molybdenum steel X2CrNiMoN22-5-3329 (2205)
1.4470 Chromium-nickel-molybdenum steel GX2CrNiMoN22-5-3 329
1.4517Chromium-nickel-molybdenum steel with copper addition GX2CrNiMoCuN25-6-3-3
1.4528 Blade steel X105CrCoMo182 440B+Co
1.4541 Chromium-nickel steel with titanium ad-dition X6CrNiTi18-10 321
1.4542 Chromium-nickel steel with copper and niobium additions X5CrNiCuNb16-4 630
1.4571 Chromium-nickel steel with titanium ad-dition X6CrNiMoTi17-12-2 316Ti
1.4581Chromium-nickel-molybdenum steel with niobium addition GX5CrNiMoNb19-11-2
316 / 316Nb
Abrasite Chilled cast iron material for use in strongly abrasive fluidsAl Light metal material (aluminium)Al-oxide Aluminium oxideC Carbon
Ceram Coating with very high adhesive strength for long-lasting corrosion protectionComposite High-strength plastic materialCr Chromium
EN-GJL
Cast iron with lamellar graphite, also re-ferred to as grey cast iron. The use of grey cast iron in domestic water systems is governed by the Drinking Water Directive 98/83/EC and applicable recognised tech-nical rules and standards!
EN-GJL 200 Grey cast iron GG20EN-GJL 250 Grey cast iron GG25
-
9General notes and abbreviations
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Wear and tearPumps or parts of pumps are subject to wear in accordance with the current technical standards (DIN 31051/DIN-EN 13306). This wear may vary depending on the operating parameters (temperature, pressure, speed, water conditions) and the installation/usage situa-tion and may result in the failure of the above products/components, including their electrical/electronic circuits, at different times.Wear or wearing parts are all components subject to rotary or dynam-ic stress, including electronic components to which voltage is ap-plied, including in particular:
Gaskets (including mechanical seals), seal rings. Stuffing boxes. Bearings and shafts. Impellers and pump components. Thrust rings and wear rings. Wear rings / wear plates. Macerators. Condensers. Relays/contactors/switches. Electronic circuits, semiconductor components etc.
Pumps and continuous-flow machines (such as submersible mixers and recirculation pumps) and their coated components (cataphoretic, 2K or Ceram coating) are subject to constant wear due to the abrasive content of the fluids. For this reason the coating of these units is also counted as a wearing part!
We do not accept any liability for faults or defects arising from natu-ral wear and tear.
Wilo General Terms of Delivery and ServiceThe latest version of our General Terms of Delivery and Service can be found on the Internet atwww.wilo.com
EN-GJS
Cast iron with spheroidal graphite, also referred to as spheroidal cast iron. The use of spheroidal cast iron in domestic water systems is governed by the Drinking Wa-ter Directive 98/83/EC and applicable rec-ognised technical rules and standards!
EN-GJS-500-7 Spheroidal cast iron GGG50G-Al Si12 Die-cast aluminiumGfK Fibreglass plasticGG See EN-GJLGGG See EN-GJSInox Stainless steelABS Acrylic butadiene styrenePA 30GF See CompositePE-HD High-density polyethylene
PP-GF30 Polypropylene, reinforced with 30% fi-breglassPUR PolyurethaneSiC Silicon carbideSt SteelSt.vz. Galvanised steelV2A Material group, e.g. 1.4301, 1.4306 304V4A Material group, e.g. 1.4404, 1.4571 316
Material Meaning AISI
-
10 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
General notesInformation for the pump curve graph
Raw water intake
Wilo-Sub TWU 4-04.. (Example)
TWU 4-0409-C
TWU 4-0405-C
TWU 4-0407-C
TWU 4-0444-C
TWU 4-0414-C
TWU 4-0418-C
TWU 4-0427-C
TWU 4-0448-C
TWU 4-0435-C
0 1 2 3 4 5 6
0
0 4 8 12 16 20
0 5 10 15 20 25
0
40
80
120
160
200
240
280
320
360
0
200
400
600
800
1000
1200
0 1 2 3 4 5 6
[%]
0
20
40
60
Pump curves, Wilo-Sub TWU 4-04..-C
Minimum efciency index (MEI): 0.7
Pump series
Hydraulic reference number according to ErP Directive
Delivery head in meters.
Pump type
Hydraulic efciency in %.
Flow rate in m/h.
H/Q pump curve
Delivery head in feet.
Flow rate in m/h.
Pump curve basis
H [m]
Q [m/h]
Q [m/h]
Q [l/s]
Q [Imp. g.p.m.]
Q [US g.p.m.]
H [ft]
0.4 0.8 1.2 1.6
1~230 V or 3~400 V, 50 Hz, = 1 kg/dm, v = 1x10-6 m/s, ISO 9906 appendix A, = pump efciency
Flow rate in US gallons per minute.
-
11
Submersible pumps3 and 4 series
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Subm
ersi
ble
pum
ps
Series overview
Series Wilo-Sub TWU 3 Wilo-Sub TWU 3 HS Wilo-Sub TWU 4 Wilo-Sub TWU 4-...-GT
Prod-uct photo
Duty chart
Design Multistage 3 submersible pump in tie strap version for vertical or horizontal installation
Multistage, frequency controlled 3 submersible pump in tie strap version for vertical or horizontal installation
Multistage 4" submersible pump in tie strap version for vertical and horizontal installation
Multistage 4 submersible pump in tie strap version for vertical and horizontal installa-tion
Appli-cation
For private water supply from boreholes, wells and rainwa-ter storage tanks
For domestic water supply, sprinkling and irrigation
For pumping water without long-fibre and abrasive con-stituents
For private water supply from boreholes, wells and rainwa-ter storage tanks
For domestic water supply, sprinkling and irrigation
For pumping water without long-fibre and abrasive con-stituents
For water supply from bore-holes and rainwater storage tanks
For domestic water supply, sprinkling and irrigation
Pressure boosting Lowering the water level For pumping water without
long-fibre and abrasive con-stituents
Geothermal applications For water supply from bore-
holes and rainwater storage tanks
For domestic water supply, sprinkling and irrigation
Pressure boosting Lowering the water level For pumping water without
long-fibre and abrasive con-stituents
Hmax 130 m 96 m 322 m 33 m
Qmax 2.6 m3/h 6.5 m3/h 22 m3/h 6 m3/h
Special fea-tures/prod-uct ad-vantag-es
Rewindable motor Integrated non-return valve Parts that come in contact
with fluids are corrosion-free Pump connection head and
flange made of stainless steel Vertical and horizontal instal-
lation possible Single-phase version with
starting capacitor and On/Off switch
Expanded flow capacity by in-creased rotation speed (up to 8400 rpm)
Rewindable motor Integrated non-return valve Parts that come in contact
with fluids are corrosion-free Including frequency converter
(HS-E: external, installed in the piping; HS-I: built into the motor)
Vertical and horizontal instal-lation possible
Parts in contact with fluid are corrosion-free
Low-wearing due to floating impellers
Integrated non-return valve Vertical and horizontal instal-
lation possible
Parts that come in contact with fluids are corrosion-free
Low-wearing due to floating impellers
Integrated non-return valve Simple and quick extension of
the motor cable without dis-mantling the pump (for QC version)
Vertical and horizontal instal-lation possible
Further infor-mation
Series information from page 16Wilo online catalogue at www.wilo.com
Series information from page 18Wilo online catalogue at www.wilo.com
Series information from page 20 Wilo online catalogue at www.wilo.com
Series information from page 22Wilo online catalogue at www.wilo.com
Wilo-SubTWU 3-...H
[m]
0 0,50
20
40
60
80
100
1,0 1,5 2,0 Q[m/h]
-0115
-0123
-0130
-0145
05 63 4210 Q[m/h]
20
40
60
80
100
H[m
]
Wilo-SubTWU 3-...-HS..
40
80
120
160
200
240
280
H/m
0Q/m/h1053 421 14
Wilo-SubTWU 4-...-C
Q[m/h]0 21 43 65
H[m
]
0
4
8
12
16
20
24
28
Wilo-SubTWU 4-...-GT
-
12 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series overview
Series Wilo-Sub TWU 4-QC Wilo-Sub TWI 4-..-B Wilo-Sub TWI 5/TWI 5-SE
Product photo
Duty chart
Design Multistage 4 submersible pump in tie strap version for vertical and horizontal installation
Multistage 4 submersible pump in tie strap version for vertical or horizontal installation
5" submersible pump in stainless steel, multistage
Application
For water supply from boreholes and rainwater storage tanks
For domestic water supply, sprinkling and irrigation
Pressure boosting Lowering the water level For pumping water without long-fi-
bre and abrasive constituents
For water and potable water supply from boreholes and rainwater storage
Process water supply For municipal water supply, sprinkling
and irrigation Pressure boosting Lowering the water level For pumping water in industrial appli-
cations For pumping water without long-fi-
bre and abrasive constituents
Submersible pumps Pumping from wells, rainwater storage
tanks and vessels Irrigation, sprinkling and pumping out Water supply Rainwater utilisation
Hmax 231 m 315 m 88 m
Qmax 12 m3/h 21 m3/h 16 m3/h
Special features/product advan-tages
Parts that come in contact with fluids are corrosion-free
Low-wearing due to floating impellers Integrated non-return valve Quick and easy extension of motor
cable, without dismantling the pump Vertical and horizontal installation
possible
Easy maintenance due to rapid instal-lation and dismantling
Integrated non-return valve Vertical and horizontal installation
possible
Single-phase AC current version- Pre-installed with switchbox- Thermal motor protection
FS version with integrated float switch Self-cooling motor (installation out-
side water possible) TWI 5 version with standard inlet bas-
ket Variants:
- SE: with lateral inlet connecting piece
- FS: with built-in float switchFurther information
Series information from page 24Wilo online catalogue at www.wilo.com
Series information from page 26Wilo online catalogue at www.wilo.com
Series information from page 28Wilo online catalogue at www.wilo.com
0
40
80
120
160
200
240
H[m
]
52,51 1,5 Q[m/h]0
Wilo-Sub TWU 4-...-QC
0
40
80
120
160
200
240
280
0,6 1 2 3 4 6 8 10
Wilo-SubTWI 4...-BH
/m
Q/m/h 0102030405060
7080
H[m]
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Wilo-Sub TWI 5/ ..-SE 50 Hz
Q[m/h]
304-308504-506
903-904
-
13
Submersible pumps6" series
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Subm
ersi
ble
pum
ps
Series overview
Series Wilo-Sub TWU 6-..-B Wilo-Sub TWI 6-..-B Wilo-EMU 6"
Product photo
Duty chart
Design Multistage 6 submersible pump in tie strap version for vertical and horizontal installation
Multistage 6 submersible pump in tie strap version for vertical or horizontal installation
Multistage 6 submersible pump in tie rod version for vertical and horizontal installation
Application
For water supply from boreholes and rainwater storage tanks
For sprinkling and irrigation For lowering the water level For pumping water without long-fi-
bre and abrasive constituents
For water and potable water supply from boreholes and rainwater storage tanks
Process water supply For municipal water supply, sprinkling
and irrigation Pressure boosting Lowering the water level For pumping water in industrial appli-
cations For pumping water without long-fi-
bre and abrasive constituents
Process water supply from boreholes and rainwater storage tanks
Municipal water supply Sprinkling and irrigation Pressure boosting Pumping of water in industrial appli-
cations and water control Operation of fountains Pumping of water without long-fibre
and abrasive constituents
Hmax 320 m 427 m 410 m
Qmax 72 m3/h 78 m3/h 32 m3/h
Special features/product advan-tages
Impellers made of bronze Integrated non-return valve Immersion depth up to 350 m Vertical and horizontal installation
possible
Easy maintenance due to rapid instal-lation and dismantling
Integrated non-return valve Vertical and horizontal installation
possible Standard and configurable versions
available Star/delta starting Cast and rewindable motors
Pumping water from great depths Corrosion-free and wear-resistant
due to housing made of NiAl-Bz and impellers made of Noryl
Integrated non-return valve Cast and rewindable motors Vertical and horizontal installation
possible (depending on the number of stages)
Further information
Series information from page 30Wilo online catalogue at www.wilo.com
Series information from page 49Wilo online catalogue at www.wilo.com
Series information from page 82Wilo online catalogue at www.wilo.com
H/m
0
100
200
300
Q/m/h10050 75250
Wilo-SubTWU 6-... / TWU 8-...
TWU 8"
TWU 6"
40
4 53 6 7 10 15 20 30 40 50
120
200
280
360
Wilo-SubTWI 6-..-BH
/m
Q/m/h 0,4 1 2 3 4 6 10 150
80
160
240
320
Wilo-EMU 6
Q/l/s
H/m
-
14 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps8" series
Series overview
Series Wilo-Sub TWU 8-..-B Wilo-Sub TWI 8-..-B Wilo-EMU 8"
Product photo
Duty chart
Design Multistage 8 submersible pump in tie strap version for vertical and horizontal installation
Multistage 8 submersible pump in tie strap version for vertical or horizontal installation
Multistage 8 submersible pump in sec-tional construction for vertical and hori-zontal installation
Application
For water supply from boreholes and rainwater storage tanks
For sprinkling and irrigation For lowering the water level For pumping water without long-fi-
bre and abrasive constituents
For water and potable water supply from boreholes and rainwater storage
Process water supply For municipal water supply, sprinkling
and irrigation Pressure boosting Lowering the water level For pumping water in industrial appli-
cations For pumping water without long-fi-
bre and abrasive constituents
For potable water supply / general wa-ter supply from boreholes and rainwa-ter storage tanks
Process water supply Municipal water supply Sprinkling and irrigation Pressure boosting Pumping water in industrial applica-
tions and water control Utilisation of geothermal energy Utilisation in offshore areas
Hmax 380 m 420 m 600 m
Qmax 132 m3/h 120 m3/h 200 m3/h
Special features/product advan-tages
Impellers made of bronze Integrated non-return valve Immersion depth up to 350 m Vertical and horizontal installation
possible
Easy maintenance due to rapid instal-lation and dismantling
Integrated non-return valve Vertical and horizontal (stage-de-
pendent) installation possible Standard and configurable versions
available Star/delta starting Cast and rewindable motors
Pumping water from great depths Impellers made of Noryl or zinc-free
bronze Wear-resistant GI bearing sleeve Integrated non-return valve (depend-
ing on type) Special materials possible Cast and rewindable motors Trimming the impeller allows individu-
al adjustment to the duty point (de-pending on type)
Vertical and horizontal installation possible (depending on the number of stages)
Ceram CT coating possible to increase effectiveness (depending on type)
Further information
Series information from page 129Wilo online catalogue at www.wilo.com
Series information from page 141Wilo online catalogue at www.wilo.com
Series information from page 164Wilo online catalogue at www.wilo.com
H/m
0
100
200
300
Q/m/h10050 75250
Wilo-SubTWU 6-... / TWU 8-...
TWU 8"
TWU 6"
15 20 30 40 50 60 80 10011
40
120
200
280
360
Wilo-SubTWI 8-..-BH
/m
Q/m/h0
80
160
240
320
400
480
H[m
]
1 Q [l/s]2 3 5 10 20 30
Wilo-EMU 8
-
15
Submersible pumps10"...24" series
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Subm
ersi
ble
pum
ps
Series overview
Series Wilo-Sub TWI 10-..-A Wilo-EMU 10" ... 24" Wilo-EMU polder pumps
Product photo
Duty chart
Design Multistage 10 submersible pump in tie strap version for vertical or horizontal installation
Multistage 10...24 submersible pump in sectional construction for vertical and horizontal installation
Multistage submersible pump as polder pump for vertical installation
Application
For water and potable water supply from boreholes and rainwater storage
Process water supply For municipal water supply, sprinkling
and irrigation Pressure boosting Lowering the water level For pumping water in industrial appli-
cations For pumping water without long-fi-
bre and abrasive constituents
For potable water supply / general wa-ter supply from boreholes and rainwa-ter storage tanks
Process water supply Municipal water supply Sprinkling and irrigation Pressure boosting Pumping water in industrial applica-
tions and for water control Utilisation of geothermal energy Utilisation in offshore areas
Potable and process water from tanks or shallow bodies of water
Municipal water supply Sprinkling and irrigation Lowering the water level Industrial applications Utilisation of geothermal energy Utilisation in offshore areas
Hmax 500 m 560 m 160 m
Qmax 160 m3/h 2400 m3/h 1200 m3/h
Special features/product advan-tages
Easy maintenance due to rapid instal-lation and dismantling
Integrated non-return valve Vertical and horizontal (stage-de-
pendent) installation possible Star/delta starting Cast and rewindable motors Hydraulics in corrosion-free stainless
steel design
Water pumping with large volume flows
Corrosion-resistant impellers made of zinc-free bronze
Wear-resistant GI bushing (depend-ing on type)
Special materials possible Cast or rewindable motors Individual adjustment to duty point
due to impeller correction 4-pole motors for long service life and
high degree of efficiency Motors with CoolAct technology for
high power densities High voltage up to 3.3 kV (U 15, U
17, NU 16) or up to 6 kV (U 21) possible on request
Vertical and horizontal installation possible (depending on the number of stages)
Ceram CT coating possible to increase effectiveness
Deep water lowering Self-cooling design Easy installation on the ascending
pipe Wear-resistant design due to differ-
ent material versions Compact design Rewindable motors Individual adjustment to duty point
due to impeller correction Ceram CT coating possible to increase
effectiveiness
Further information
Series information from page 277Wilo online catalogue at www.wilo.com
Series information from page 307Wilo online catalogue at www.wilo.com
Series information from page 388Wilo online catalogue at www.wilo.com
20 30
50100150200250300350400450
40 50 100 20060 15025
Wilo-SubTWI 10-...-AH
/m
Q/m/h 5 10 15 20 30 40 50 100 300Q[l/s]0
80
160
240
320
400
480
H[m
]
Wilo-EMU 10...24
0
H/m
140
120
100
20
40
60
80
Q/l/s10 20 30 40 50 100 160
Wilo-EMUK...P, KM...P, D...P
-
16 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series description Wilo-Sub TWU 3
DesignMultistage 3 submersible pump in tie strap version for vertical or horizontal installation
Type key
Application For private water supply from boreholes, wells and rainwater storage
tanks For domestic water supply, sprinkling and irrigation For pumping water without long-fibre and abrasive constituents
Special features/product advantages Rewindable motor Integrated non-return valve Parts that come in contact with fluids are corrosion-free Pump connection head and flange made of stainless steel Vertical and horizontal installation possible Single-phase version with starting capacitor and On/Off switch
Technical data Mains connection: 1~230 V, 50 Hz or 3~400 V, 50 Hz Immersed operating mode: S1 Fluid temperature: 3-35 C Minimum flow rate at motor: 0.08 m/s Max. sand content: 50 g/m3 Max. number of starts: 30 /h Max. immersion depth: 150 m Protection class: IP 58 Pressure connection: Rp 1
Equipment/function Multistage submersible-motor pump with radial impellers Integrated non-return valve NEMA coupling Single-phase or three-phase AC motor Integrated thermal motor protection for single-phase motor
Materials Hydraulic housing: 1.4301 stainless steel Impellers: polycarbonate Hydraulics shaft: 1.4104 stainless steel Motor housing: 1.4301 stainless steel Motor shaft: 1.4305 stainless steel
Description/designSubmersible-motor pump for vertical or horizontal installation.
HydraulicsMultistage submersible-motor pump with radial impellers with sec-tional construction. Integrated non-return valve. All parts in contact with the fluid are made of corrosion-free materials.
MotorCorrosion-free single-phase or three-phase motor for direct starting, with rewindable motor, oil-filled, self-lubricating bearing.
CoolingThe motor is cooled by the fluid. The motor must always be operated in submerged state. The limit values for the max. fluid temperature and the minimum flow rate must not be exceeded. Vertical installa-tion is possible optionally with or without cooling jacket. Cooling jacket is required for horizontal installation.
Options Motor versions for special voltages 3~230 V, 50 Hz; 1~230 V, 60 Hz;
3~380 V, 60 Hz
Scope of delivery Hydraulics + motor fully assembled 1.8 m connecting cable approved for potable water (cross-section:
4x1.5 mm2) Single-phase version including switchbox with capacitor, thermal
motor protection and On/Off switch Installation and operating instructions
Accessories Cooling jacket pipes Diaphragm pressure vessel Cable kits for potable and process water Float switch Switchgears Connection and installation material
D |
e.g. Wilo-Sub TWU 3-0115TWU Submersible pump3 Diameter of the hydraulic unit in inches ["]01 Nominal volume flow [m3/h]15 Number of hydraulic stages
-
17
Submersible pumps3 and 4 series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWU 3
Configuration No suction mode is possible with these units! The unit must be fully immersed in water during operation.
Pump curves
Wilo-Sub TWU 3-...H
[m]
0 0,50
20
10
40
30
60
50
80
90
70
100
110
120
1,0 1,5 2,0 2,5 Q [m/h]
TWU 3-0115
TWU 3-0123
TWU 3-0130
TWU 3-0145
-
18 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series description Wilo-Sub TWU 3 HS
DesignMultistage, frequency controlled 3 submersible pump in tie strap version for vertical or horizontal installation
Type key
Application For private water supply from boreholes, wells and rainwater storage
tanks For domestic water supply, sprinkling and irrigation For pumping water without long-fibre and abrasive constituents
Special features/product advantages Expanded flow capacity by increased rotation speed (up to 8400 rpm) Rewindable motor Integrated non-return valve Parts that come in contact with fluids are corrosion-free Including frequency converter (HS-E: external, installed in the pip-
ing; HS-I: built into the motor) Vertical and horizontal installation possible
Technical dataSubmersible pump:
Supply voltage:HS-E: 1~230 V, 50/60 Hz (connection to the AC mains supply by a frequency converter )HS-I: 1~230 V, 50/60 Hz (direct connection to the AC mains supply)
Immersed operating mode: S1 Fluid temperature: 3-35 C Minimum flow rate at motor: 0.08 m/s Max. sand content: 50 g/m3
Max. number of starts: 30 /h Max. immersion depth: 150 m Protection class: IP 58 Pressure connection: Rp 1
Frequency converter for version "HS-E: Mains connection: 1~230 V, 50/60 Hz Output: 3~230 V/max.140 Hz/max.2.2 kW Fluid temperature: 3-50 C Max. pressure: 8 bar Protection class: IP X5 Connection: G 1
Equipment/function Multistage submersible-motor pump with radial impellers Integrated non-return valve Including frequency converter (HS-E: external, HS-I: built-in) Thermal motor protection built into the frequency converter
Materials Hydraulic housing: Stainless steel 1.4301 Impellers: Polycarbonate Hydraulics shaft: 1.4104 stainless steel Motor housing: Stainless steel 1.4301 Motor shaft: 1.4305 stainless steel
Description/designSubmersible pump for vertical or horizontal installation.
HydraulicsMultistage submersible pump with radial impellers with sectional construction. Integrated non-return valve. All parts in contact with the fluid are made of corrosion-free materials.
MotorCorrosion-free asynchronous motor for connection to the frequency converter supplied (HS-E) or for direct connection to the mains power supply (HS-I). Rewindable oil-filled motor with self-lubricat-ing bearings, designed for high speeds up to 8400 rpm.
Frequency converterExternal frequency converter or frequency converter integrated within the motor, for operation of the pump at speeds up to 8400 rpm, including the following functions:
Soft starter Undervoltage, overvoltage and short-circuit protection
D |
e.g. Wilo sub TWU 3-0305-HS-E-CPTWU Submersible pump3 Diameter of the hydraulic unit in inches ["]03 Nominal volume flow [m3/h]05 Number of hydraulic stagesHS High-speed versionE Frequency converter version
E = external frequency converterI = external frequency converter
CP Control functionCP = constant pressure controlwithout = fixed speed with up to 8400 rpm
-
19
Submersible pumps3 and 4 series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWU 3 HS
Thermal overload protection of the motor and the frequency con-verter
The version "HS-E with external frequency converter offers the following additional equipment features:
Control function "CP: Constant pressure Avoidance of frequent switching (cycling) by leakage monitoring Dry-running protection with automatic reset Change of direction of rotation Setting for max. flow and target pressure Pressure is shown on the display Settings, operating statuses and error messages are shown by LEDs
or on the display.
The frequency converter always must be installed outside the fluid where it will be protected against overflows!
Control function "CP: Constant pressureOperation with the frequency converter means the rotation speed of the unit is adapted to the current water requirements automatically. As a result, the submersible pump always delivers a constant pres-sure.
CoolingThe motor is cooled by the fluid. The motor must always be operated in submerged state. The limit values for the max. fluid temperature and the minimum flow rate must not be exceeded. In cases of vertical installation, a cooling jacket must be provided de-pending on the diameter of the bore. In cases of horizontal installa-tion, a cooling jacket must always be provided .
The external frequency converter is also cooled by the fluid. For this the frequency converter must be installed directly in the piping out-side the fluid (overflow-proof).
Options Special cable lengths on request
Scope of delivery Hydraulics + motor ready assembled Frequency converter 1.75 m connecting cable approved for potable water (cross-section:
4x1.5 mm2) Installation and operating instructions
Accessories Cooling jacket pipes Diaphragm pressure vessel Cable kits for potable and process water Float switch Switchgears Connection and installation material
Configuration No suction mode is possible with these units! The unit must be fully immersed in water during operation. An adapter of Rp 1 to G 1 in required for installation. This must be
provided on site!
Pump curves
TWU 3-05..HS..
TWU 3-03..HS..
TWU 3-02..HS..
0,2 2,01,00,50,25 1,50,3 0,4 0,6 0,7 0,8
110
120
0
Q [l/s]
5 632,5 4210 1,5 7 Q [m/h]
10
20
30
40
50
60
70
80
90
100
H[m] Wilo-Sub TWU 3-...-HS..
-
20 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series description Wilo-Sub TWU 4
DesignMultistage 4 submersible pump in tie strap version for vertical and horizontal installation
Type key
Application For water supply from boreholes and rainwater storage tanks For domestic water supply, sprinkling and irrigation Pressure boosting Lowering the water level For pumping water without long-fibre and abrasive constituents
Special features/product advantages Parts in contact with fluid are corrosion-free Low-wearing due to floating impellers Integrated non-return valve Vertical and horizontal installation possible
Technical data Minimum Efficiency Index (MEI) up to 0.7 Mains connection: 1~230 V, 50 Hz or 3~400 V, 50 Hz Immersed operating mode: S1 Fluid temperature: 3-30 C Minimum flow rate at motor: 0.08 m/s Max. sand content: 50 g/m3 Max. number of starts: 20/h Max. immersion depth: 200 m Protection class: IP 68 Pressure connection: Rp 1 - Rp 2
Equipment/function Multistage submersible-motor pump with radial or semi-axial impel-
lers Hermetically cast motors Integrated non-return valve NEMA coupling Single-phase or three-phase motor Integrated thermal motor protection for single-phase motor
Materials Hydraulic housing: Stainless steel 1.4301 Impellers: Noryl Hydraulics shaft: 1.4104 stainless steel Motor housing: Stainless steel 1.4301 Motor shaft: 1.4305 stainless steel
Description/designSubmersible-motor pump for vertical or horizontal installation.
HydraulicsMultistage submersible-motor pump with radial or semi-axial impel-lers in sectional construction. Integrated non-return valve. All parts in contact with the fluid are made of corrosion-free materials.
MotorCorrosion-free single-phase or three-phase motor for direct start-ing.Sealed and hermetically cast motor with enamel-insulated wind-ing, resin-impregnated, self-lubricating bearing, with water-glycol filling.
CoolingThe motor is cooled by the fluid. The motor must always be operated in submerged state. The limit values for the max. fluid temperature and the minimum flow rate must not be exceeded. Vertical installa-tion is possible optionally with or without cooling jacket. Cooling jacket is required for horizontal installation.
Options Motor versions for special voltages 3~230 V, 50 Hz; 3~500 V, 50 Hz;
1~230 V, 60 Hz; 3~230 V, 60 Hz; 3~380 V, 60 Hz; 3~460 V, 60 Hz
D |
e.g. Wilo-Sub TWU 4-0203-CTWU Submersible pump4 Diameter of the hydraulic unit in inches ["]02 Nominal volume flow [m3/h]03 Number of hydraulic stagesC Series generation
-
21
Submersible pumps3 and 4 series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWU 4
Scope of delivery Hydraulics + motor fully mounted 1.5/1.75/2.5 m connecting cable approved for potable water (cross-
section: 4x1.5 mm2) Single-phase version including switchbox with capacitor, thermal
motor protection and On/Off switch Installation and operating instructions
Accessories Cooling jacket pipes Diaphragm pressure vessel Cable kits for potable and process water Float switch Switchgears Connection and installation material
Configuration No suction mode is possible with these units! The unit must be fully immersed in water during operation.
General notes - ErP (ecological design-) directive The benchmark for most efficient water pumps is MEI 0.70 The efficiency of a pump with a trimmed impeller is usually lower
than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to re-duced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the sys-tem.
Information on benchmark efficiency is available at www.europ-ump.org/efficiencycharts
Pump curves
20
40
60
80
100
120
140
160
180
200
220
240
260
280
300
H[m]
0Q [m/h]1412105 632,5 421 1,5 87 9 16 20
TWU 4 - 02.
TWU 4 - 04.
TWU 4 - 08.
TWU 4 - 16
Wilo-Sub TWU 4-...-C
-
22 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series description Wilo-Sub TWU 4-...-GT
DesignMultistage 4" submersible pump in tie strap version for vertical and horizontal installation
Type key
Application Geothermal applications For water supply from boreholes and rainwater storage tanks For domestic water supply, sprinkling and irrigation Pressure boosting Lowering the water level For pumping water without long-fibre and abrasive constituents
Special features/product advantages Parts that come in contact with fluids are corrosion-free Low-wearing due to floating impellers Integrated non-return valve Simple and quick extension of the motor cable without dismantling
the pump (for QC version) Vertical and horizontal installation possible
Technical data Minimum Efficiency Index (MEI) up to 0.7 Mains connection: 3~400 V, 50 Hz, Submerged operating mode: S1 Fluid temperature: 3-30 C Minimum flow rate at motor: 0.08 m/s Max. sand content: 50 g/m3
Max. number of starts: 20/h Max. submersion depth: 200 m Protection class: IP 68 Pressure connection: Rp 1
Equipment/function Multi-stage submersible pump with radial or semi-axial impellers Hermetically cast motors Integrated non-return valve NEMA coupling Three-phase motor
Materials Hydraulic housing: Stainless steel 1.4301 Impellers: Noryl Hydraulics shaft: Stainless steel 1.4104 Motor housing: Stainless steel 1.4301 Motor shaft: Stainless steel 1.4305
Description/designSubmersible pump for vertical or horizontal installation.
HydraulicsMulti-stage submersible pump with radial or semi-axial impellers in sectional construction. Integrated non-return valve. All parts in con-tact with the fluid are made of corrosion-free materials.
MotorCorrosion-free three-phase motor for direct starting. Sealed and hermetically cast motor with enamel-insulated winding, resin-im-pregnated, self-lubricating bearing, with water-glycol filling.
CoolingThe motor is cooled by the fluid. The motor must always be operated in submerged state. The limit values for the maximum fluid tempera-ture and the minimum flow rate must not be exceeded. Vertical in-stallation is possible optionally with or without cooling jacket. Cool-ing jacket is required for horizontal installation.
Options Motor versions for special voltages 3~380 V, 60 Hz; 3~460 V, 60 Hz
a
e.g. Wilo-Sub TWU 4-0203-C-QC-GTTWU Submersible pump4 Diameter of the hydraulic unit in inches ["]02 Nominal volume flow [m3/h]03 Number of hydraulic stagesC Series generationQC Quick Connect Cable
for simple and fastextension for the motor cable
GT for geothermal applications
-
23
Submersible pumps3 and 4 series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWU 4-...-GT
Scope of delivery Hydraulics and motor ready assembled Connecting cable approved for potable water (cross-section 4 x 1.5
mm2) Installation and operating instructions
Accessories Cooling jacket pipes Diaphragm pressure vessel Cable kits for potable and process water Float switch Switchgears Connection and installation material
Configuration No suction mode is possible with these units! The unit must be fully immersed in water during operation.
General notes - ErP (ecological design-) directive The benchmark for most efficient water pumps is MEI 0.70 The efficiency of a pump with a trimmed impeller is usually lower
than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to re-duced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the sys-tem.
Information on benchmark efficiency is available at www.europ-ump.org/efficiencycharts
Pump curves
Q/m/h0 1 2 3 4 5 6
Q/l/s0 0 ,4 0,8 1 ,2 1,6
H/m
0
4
8
12
16
20
24
28
32
Wilo-Sub TWU 4-...-GT
-
24 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series description Wilo-Sub TWU 4-QC
DesignMultistage 4 submersible pump in tie strap version for vertical and horizontal installation
Type key
Application For water supply from boreholes and rainwater storage tanks For domestic water supply, sprinkling and irrigation Pressure boosting Lowering the water level For pumping water without long-fibre and abrasive constituents
Special features/product advantages Parts that come in contact with fluids are corrosion-free Low-wearing due to floating impellers Integrated non-return valve Quick and easy extension of motor cable, without dismantling the
pump Vertical and horizontal installation possible
Technical data Minimum Efficiency Index (MEI) up to 0.7 Mains connection: 1~230 V, 50 Hz or 3~400 V, 50 Hz Immersed operating mode: S1 Fluid temperature: 3-30 C Minimum flow rate at motor: 0.08 m/s Max. sand content: 50 g/m3 Max. number of starts: 20/h
Max. immersion depth: 200 m Protection class: IP 68 Pressure connection: Rp 1 - Rp 2
Equipment/function Multistage submersible-motor pump with radial or semi-axial impel-
lers Hermetically cast motors Integrated non-return valve NEMA coupling Single-phase or three-phase motor Integrated thermal motor protection for single-phase motor
Materials Hydraulic housing: 1.4301 stainless steel Impellers: Noryl Hydraulics shaft: 1.4104 stainless steel Motor housing: 1.4301 stainless steel Motor shaft: 1.4305 stainless steel
Description/designSubmersible-motor pump for vertical or horizontal installation.
HydraulicsMultistage submersible-motor pump with radial or semi-axial impel-lers in sectional construction. Integrated non-return valve. All parts in contact with the fluid are made of corrosion-free materials.
MotorCorrosion-free single-phase or three-phase AC motor for direct starting. Sealed and hermetically cast motor, resin-impregnated, with enamel-insulated winding, self-lubricating bearing, with water-gly-col filling.
CoolingThe motor is cooled by the fluid. The motor must always be operated in submerged state. The limit values for the max. fluid temperature and the minimum flow rate must not be exceeded. Vertical installa-tion is possible optionally with or without cooling jacket. Cooling jacket is required for horizontal installation.
D |
e.g. Wilo-Sub TWU 4-0203-C-QCTWU Submersible pump4 Diameter of the hydraulic unit in inches ["]02 Nominal volume flow [m3/h]03 Number of hydraulic stagesC Series generationQC Quick Connect Cable
for simple and fastextension for the motor cable
-
25
Submersible pumps3 and 4 series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWU 4-QC
Options Motor versions for special voltages 1~230 V, 60 Hz; 3~380 V, 60 Hz
Scope of delivery Hydraulics + motor fully mounted 1.5 or 1.75 m connecting cable approved for potable water (cross-
section: 4x1.5 mm2) Cable binders Retaining cable made of polypropylene 1x clamp for fixing the retaining cable to the unit Single-phase version including switchbox with capacitor, thermal
motor protection and On/Off switch Installation and operating instructions
Accessories Quick Connect Cable: Quick-connection cable for fast and easy ex-
tension of the motor cable. Cooling jacket pipes Diaphragm pressure vessel Cable kits for potable and process water Float switch Switchgears Connection and installation material
Configuration No suction mode is possible with these units! The unit must be fully immersed in water during operation.
General notes - ErP (ecological design-) directive The benchmark for most efficient water pumps is MEI 0.70 The efficiency of a pump with a trimmed impeller is usually lower
than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to re-duced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the sys-tem.
Information on benchmark efficiency is available at www.europ-ump.org/efficiencycharts
Pump curves
0
40
80
120
160
200
240
280
1052,51 1,5 Q [m/h]0
Wilo-Sub TWU 4-...-QC
02..-C-QC
04..-C-QC
08..-C-QC
H[m]
-
26 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series description Wilo-Sub TWI 4-..-B
DesignMultistage 4 submersible pump in tie strap version for vertical or horizontal installation
Type key
Application For water and potable water supply from boreholes and rainwater
storage Process water supply For municipal water supply, sprinkling and irrigation Pressure boosting Lowering the water level For pumping water in industrial applications For pumping water without long-fibre and abrasive constituents
Special features/product advantages Easy maintenance due to rapid installation and dismantling Integrated non-return valve Vertical and horizontal installation possible
Technical data Minimum Efficiency Index (MEI) up to 0.7 Mains connection: 1~230 V, 50 Hz or 3~400 V, 50 Hz Immersed operating mode: S1 Fluid temperature: 3-30 C Minimum flow rate at motor: 0.1 m/s Max. sand content: 50 g/m3 Max. number of starts: 20/h Max. immersion depth: 350 m Protection class: IP 68 Pressure connection: Rp 1 - Rp 2
Equipment/function Multistage submersible-motor pump with radial impellers Integrated non-return valve NEMA coupling Single-phase or three-phase motor Hermetically cast motors
Materials Hydraulic housing: 1.4301 stainless steel Impellers: 1.4301 stainless steel Hydraulics shaft: 1.4057 stainless steel Motor housing: 1.4301 stainless steel Motor shaft: 1.4305 stainless steel
Description/designSubmersible-motor pump for vertical or horizontal installation.
HydraulicsMultistage submersible-motor pump with 4" NEMA connection and radial or semi-axial impellers with sectional construction. Integrated non-return valve. All parts in contact with the fluid are made of cor-rosion-free materials.
MotorCorrosion-free single-phase or three-phase AC motor for direct starting. Sealed and hermetically cast motor, resin-impregnated, with enamel-insulated winding, self-lubricating bearing, with water-gly-col filling.
CoolingThe motor is cooled by the fluid. The motor must always be operated in submerged state. The limit values for the max. fluid temperature and the minimum flow rate must not be exceeded. Vertical installa-tion is possible optionally with or without cooling jacket. Cooling jacket is required for horizontal installation.
Pressure shroudThe pressure shroud is used for direct installation of the unit in the pipe system. Standard models are without mounted non-return valves. The maximum inlet pressure is 10 bar.
D | Z
e.g. Wilo-Sub TWI 4.01-09-BTWI Submersible pump4 Diameter of the hydraulic unit in inches ["]01 Nominal volume flow [m3/h]09 Number of hydraulic stagesB Series generation
-
27
Submersible pumps3 and 4 series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWI 4-..-B
Options Hydraulics in 1.4401 stainless steel Three-phase AC motor in 1.4401 stainless steel 60 Hz version Single-phase motor without soft starter, with integrated lightning
and overload protection up to 1.1 kW
Scope of delivery Hydraulics + motor fully assembled 1.5/2.5 m connecting cable approved for potable water (cross-sec-
tion: 4x1.5 mm2) Single-phase version including switchbox with capacitor, thermal
motor protection and On/Off switch Installation and operating instructions
Accessories Cooling jacket pipes Pressure shroud (for configured units) Diaphragm pressure vessel Cable kits for potable water and process water Switchgears
Configuration No suction mode is possible with these units! The unit must be fully immersed in water during operation.
General notes - ErP (ecological design-) directive The benchmark for most efficient water pumps is MEI 0.70 The efficiency of a pump with a trimmed impeller is usually lower
than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to re-duced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the sys-tem.
Information on benchmark efficiency is available at www.europ-ump.org/efficiencycharts
Pump curves
TWI 04.03
TWI 04.14
TWI 04.09
TWI 04.05
TWI 04.02
TWI 04.01
0
20
40
60
80
100
120
140
160
180
200
220
240
260
280
300
320
H[m]
0,6 0,8 1 1,2 1,6 2 2,4 3 4 5 6 7 8 10 12 16 Q [m/h]149
Wilo-Sub TWI 4...-B
-
28 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps3 and 4 series
Series description Wilo-Sub TWI 5/TWI 5-SE
Design5" submersible pump in stainless steel, multistage
Type key
ApplicationSubmersible pumps
Pumping from wells, rainwater storage tanks and vessels Irrigation, sprinkling and pumping out Water supply Rainwater utilisation
Special features/product advantages Single-phase AC current version
- Pre-installed with switchbox- Thermal motor protection
FS version with integrated float switch Self-cooling motor (installation outside water possible) TWI 5 version with standard inlet basket Variants:
- SE: with lateral inlet connecting piece- FS: with built-in float switch
Technical data Mains connection 1~230 V, 50 Hz / 3~400 V, 50 Hz Fluid temperature max. +5 C to +35 C Max. operating pressure 10 bar Protection class IP 68 Pressure-side connection Rp 1 Connection on suction side for SE version Rp 1
Equipment/function 20 m safety cable 20 m H07RN-F cable Single-phase AC version
- Pre-installed with switchbox- Overcurrent protection of the motor
Materials Pump housing: Stainless steel 1.4301 Impeller: 1.4301 Shaft: 1.4301 Mechanical seal: SIC/SIC and carbon/ceramic Stage chambers: 1.4301 Diffuser/injector: 1.4301 Gaskets: NBR
Description/design Multistage construction complete in AISI304 KTW & TV-certified Double mechanical seal SIC/SIC Detachable connection cable Generously dimensioned water-cooled motor Scope of delivery includes 20 m connecting cable and safety cable
Scope of delivery Pump with 20 m connecting cable Safety cable made of polypropylene Installation and operating instructions
Accessories Gate valve Non-return valve Switchgear and motor protection Protection switch Float switch Acoustic overflow alarm WILO Fluidcontrol (EK) Pressure controller Suction filter with floater:
- Coarse filter- Fine filter
D |
Example: TWI5-SE 304 EM-FSTWI Submersible pump made of stainless steel5 Pump diameter (5)[Space] Suction through strainer SE Connection G 1 on suction side (for floating extractor)3 Nominal flow rate Q in m/h (at optimum efficiency)04 Number of stepsEM Single-phase current, 1~230 V, 50 HzDM Three-phase current, 3~400 V, 50 HzFS With float switch
-
29
Submersible pumps3 and 4 series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWI 5/TWI 5-SE
Pump curves
0
10
20
30
40
50
60
70
80
90
H[m
]
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Wilo-Sub TWI 5/ ..-SE 50 Hz
Q[m/h]
304-308
504-506
903-904
-
30 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Series description Wilo-Sub TWU 6-..-B
DesignMultistage 6 submersible pump in tie strap version for vertical and horizontal installation
Type key
Application For water supply from boreholes and rainwater storage tanks For sprinkling and irrigation For lowering the water level For pumping water without long-fibre and abrasive constituents
Special features/product advantages Impellers made of bronze Integrated non-return valve Immersion depth up to 350 m Vertical and horizontal installation possible
Technical data Minimum Efficiency Index (MEI) up to 0.4 (only TWU 6) Mains connection: 3~400 V, 50 Hz Immersed operating mode: S1 Fluid temperature: 3-30 C Minimum flow rate at motor: 0.08-0.16 m/s Max. sand content: 50 g/m3 Max. number of starts: 20/h Max. immersion depth: TWU 6... = 250 m; TWU 8... = 350 m Protection class: IP 68 Pressure connection: Rp 2 - Rp 5
Equipment/function Multistage submersible pump with radial or semi-axial impellers Integrated non-return valve NEMA coupling Three-phase motor Hermetically cast motors
Materials Hydraulic housing: EN-GJL-200 Impellers: Bronze Hydraulics shaft: Steel 1.4006 Motor housing: Stainless steel 1.4301 Motor shaft: 1.4305 stainless steel
Description/designSubmersible pump for vertical or horizontal installation.
HydraulicsMultistage submersible pump with radial or semi-axial impellers. In-tegrated non-return valve.
MotorThree-phase motor for direct starting. Sealed and hermetically cast motor with enamel-insulated winding, resin-impregnated, self-lu-bricating bearing, with water-glycol filling.
CoolingThe motor is cooled by the fluid. The motor must always be operated in submerged state. The limit values for the max. fluid temperature and the minimum flow rate must not be exceeded. Vertical installa-tion is possible optionally with or without cooling jacket. Cooling jacket is required for horizontal installation.
Options Rewindable motor Star/delta starting PT100 sensor for thermal motor monitoring Motor housing made of 1.4571 material Motor shaft made of 1.4460 material Motor versions for special voltages 3~230 V, 50 Hz; 3~500 V, 50 Hz,
3~230 V, 60 Hz; 3~380 V, 60 Hz; 3~460 V, 60 Hz
| x
e.g. Wilo-Sub TWU 6-4208-B-SDTWU Submersible pump6 Diameter of the hydraulic unit in inches ["]42 Nominal volume flow [m3/h]08 Number of hydraulic stagesB Series generationSD Starting type Without = Direct starting SD = star/delta starting
-
31
Submersible pumps6" series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Series description Wilo-Sub TWU 6-..-B
Scope of delivery Hydraulics + motor fully mounted 2.5/4/8 m connecting cable approved for potable water Installation and operating instructions
Accessories Cooling jacket pipes Diaphragm pressure vessel Cable kits for potable and process water Float switch Switchgears Connection and installation material
Configuration No suction mode is possible with these units! The unit must be fully immersed in water during operation.
General notes - ErP (ecological design-) directive The benchmark for most efficient water pumps is MEI up to 0.70 The efficiency of a pump with a trimmed impeller is usually lower
than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to re-duced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the sys-tem.
Information on benchmark efficiency is available at www.europ-ump.org/efficiencycharts
Pump curves
H[m]
0
100
150
50
200
300
350
250
100 125 Q [m/h]50 75250
Wilo-Sub TWU 6-... / TWU 8-...
TWU 8"
TWU 6"
-
32 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Technical data Wilo-Sub TWU 6-..-B
Wilo-Sub... Max. volume flow Max. delivery head Min. flow rate at the motor
Insulation class
Qmax Hmax v
m3/h m m/s
TWU 6-1203-B 16 30 0.1 BTWU 6-1205-B 16 50 0.1 BTWU 6-1206-B 16 60 0.1 BTWU 6-1207-B 16 70 0.1 BTWU 6-1211-B 16 110 0.1 BTWU 6-1213-B 16 130 0.1 BTWU 6-1215-B 16 150 0.2 FTWU 6-1219-B 16 190 0.2 FTWU 6-1222-B 16 220 0.2 FTWU 6-1227-B 16 270 0.2 FTWU 6-1232-B 16 320 0.2 FTWU 6-1232-B-SD 16 320 0.2 FTWU 6-1803-B 26 33 0.1 BTWU 6-1804-B 26 44 0.1 BTWU 6-1805-B 26 55 0.1 BTWU 6-1806-B 26 66 0.1 BTWU 6-1808-B 26 88 0.1 BTWU 6-1810-B 26 110 0.2 FTWU 6-1812-B 26 133 0.2 FTWU 6-1815-B 26 165 0.2 FTWU 6-1818-B 26 198 0.2 FTWU 6-1821-B 26 230 0.2 FTWU 6-1821-B-SD 26 230 0.2 FTWU 6-1824-B 26 266 0.2 FTWU 6-1824-B-SD 26 266 0.2 FTWU 6-2402-B 35 21 0.1 BTWU 6-2403-B 35 32 0.1 BTWU 6-2404-B 35 43 0.1 BTWU 6-2405-B 35 53 0.1 BTWU 6-2407-B 35 74 0.2 FTWU 6-2409-B 35 95 0.2 FTWU 6-2411-B 35 117 0.2 FTWU 6-2413-B 35 138 0.2 FTWU 6-2413-B-SD 35 138 0.2 FTWU 6-2415-B 35 159 0.2 FTWU 6-2415-B-SD 35 159 0.2 FTWU 6-2418-B 35 192 0.2 FTWU 6-2418-B-SD 35 192 0.2 F
Voltage tolerance +/- 10 % (specifications according to DIN EN 60034)
-
33
Submersible pumps6" series
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Subm
ersi
ble
pum
ps
Technical data Wilo-Sub TWU 6-..-B
Wilo-Sub... Max. volume flow Max. delivery head Min. flow rate at the motor
Insulation class
Qmax Hmax v
m3/h m m/s
TWU 6-2420-B 35 214 0.2 FTWU 6-2420-B-SD 35 214 0.2 FTWU 6-3503-B 48 26 0.1 BTWU 6-3504-B 48 35 0.1 BTWU 6-3506-B 48 52 0.2 FTWU 6-3507-B 48 61 0.2 FTWU 6-3510-B 48 88 0.2 FTWU 6-3512-B 48 105 0.2 FTWU 6-3512-B-SD 48 105 0.2 FTWU 6-3514-B 48 122 0.2 FTWU 6-3514-B-SD 48 122 0.2 FTWU 6-3517-B 48 149 0.2 FTWU 6-3517-B-SD 48 149 0.2 FTWU 6-4503-B 72 25 0.1 BTWU 6-4504-B 72 36 0.2 FTWU 6-4505-B 72 43 0.2 FTWU 6-4506-B 72 52 0.2 FTWU 6-4508-B 72 67 0.2 FTWU 6-4508-B-SD 72 67 0.2 FTWU 6-4510-B 72 88 0.2 FTWU 6-4510-B-SD 72 88 0.2 FTWU 6-4512-B 72 104 0.2 FTWU 6-4512-B-SD 72 104 0.2 FTWU 6-4514-B 72 122 0.2 FTWU 6-4514-B-SD 72 122 0.2 FTWU 6-4516-B 72 140 0.2 FTWU 6-4516-B-SD 72 140 0.2 F
Voltage tolerance +/- 10 % (specifications according to DIN EN 60034)
-
34 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Wilo-Sub TWU 6-12..-B
Pump curves Wilo-Sub TWU 6-12..-B
Minimum Efficiency Index (MEI): 0.4
3~400 V, 50 Hz, p = 1 kg/dm3, v = 1x10--6 m2/s, ISO 9906 Annex A
0 2 4 6 8 10 12 14 16
0
0
[m/h]
[l/s]
[lgpm]
H [m]
p [%]
0
50
100
200
225
150
275
325
25
75
175
125
250
300
70
60
50
40
30
4
20 6040
321
10 5030
0 2 4 6 8 10 12 14 16 [m/h]
TWU 6-1232-B
TWU 6-1227-B
TWU 6-1222-B
TWU 6-1219-B
TWU 6-1215-B
TWU 6-1213-B
TWU 6-1211-B
TWU 6-1207-B
TWU 6-1206-BTWU 6-1205-B
TWU 6-1203-B
-
35
Submersible pumps6" series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Wilo-Sub TWU 6-12..-B
Motor data
Wilo-Sub... Mains connec-tion
Motor diameter
Nominal motor power
Nominal current Length of connect-ing cable
Cable cross-section
P2 IN" kW A m mm2
TWU 6-1203-B 3~400 V, 50 Hz 4 1.1 3 2.5 4x1,5TWU 6-1205-B 3~400 V, 50 Hz 4 2.2 5.9 2.5 4x1,5TWU 6-1206-B 3~400 V, 50 Hz 4 2.2 5.9 2.5 4x1,5TWU 6-1207-B 3~400 V, 50 Hz 4 3 7.8 2.5 4x1,5TWU 6-1211-B 3~400 V, 50 Hz 4 4 10 2.5 4x1,5TWU 6-1213-B 3~400 V, 50 Hz 4 5.5 13.7 2.5 4x1,5TWU 6-1215-B 3~400 V, 50 Hz 4 5.5 13.7 2.5 4x1,5TWU 6-1219-B 3~400 V, 50 Hz 6 7.5 16 4 4x4TWU 6-1222-B 3~400 V, 50 Hz 6 9.3 20.7 4 4x4TWU 6-1227-B 3~400 V, 50 Hz 6 11 23.3 4 4x4TWU 6-1232-B 3~400 V, 50 Hz 6 15 31.3 4 4x4TWU 6-1232-B-SD 3~400 V, 50 Hz 6 15 31.3 4 2x 4x4
Information for order placements
Wilo-Sub... Mains connection Art no. Art. no. for cooling jacket pipefor vertical installation (B) for horizontal installation (D)
@TWU 6-1203-B 3~400 V, 50 Hz K 6043738 4096370 4096506TWU 6-1205-B 3~400 V, 50 Hz L 6043739 4096370 4096506TWU 6-1206-B 3~400 V, 50 Hz K 6043740 4096370 4096506TWU 6-1207-B 3~400 V, 50 Hz K 6043741 4096370 4096506TWU 6-1211-B 3~400 V, 50 Hz K 6043742 4096371 4096507TWU 6-1213-B 3~400 V, 50 Hz K 6043743 4096580 4096581TWU 6-1215-B 3~400 V, 50 Hz K 6043744 4096580 4096581TWU 6-1219-B 3~400 V, 50 Hz K 6043745 4096372 4096508TWU 6-1222-B 3~400 V, 50 Hz K 6043746 4096372 4096508TWU 6-1227-B 3~400 V, 50 Hz K 6043747 4096373 4096509TWU 6-1232-B 3~400 V, 50 Hz L 6043748 4096373 4096509TWU 6-1232-B-SD 3~400 V, 50 Hz L 6043749 4096373 4096509
-
36 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Wilo-Sub TWU 6-12..-B
Dimension drawing Wilo-Sub TWU 6-12
A = vertical, B = vertical with cooling jacket, D = horizontal with cooling jacket
Dimensions, weights
Wilo-Sub... Pressure connec-tion
Dimensions Installa-tion
Weight approx.
C1 C2 H H1 H2 R WH WV 3) m
mm kg
TWU 6-1203-B Rp 2 150 70 810.5 512 298.5 174 526 526 143 A, B, D 29.5TWU 6-1205-B Rp 2 150 70 942 586 356 117 583 583 143 A, B, D 37.1TWU 6-1206-B Rp 2 150 70 979 623 356 117 583 583 143 A, B, D 39.6TWU 6-1207-B Rp 2 150 70 1167 660 507 50 650 650 143 A, B, D 45.1TWU 6-1211-B Rp 2 150 70 1391 808 583 57 810 810 143 A, B, D 62.1TWU 6-1213-B Rp 2 150 70 1579 882 697 51 924 924 143 A, B, D 72.4TWU 6-1215-B Rp 2 150 70 1653 956 697 51 924 924 143 A, B, D 77.4TWU 6-1219-B Rp 2 215 140 1781.5 1135.5 646 70 905 905 143 A, B, D 105 TWU 6-1222-B Rp 2 215 140 2075.5 1396.5 679 24 951 951 143 A, B, D 112 TWU 6-1227-B Rp 2 215 140 2292.5 1581.5 711 67 983 983 143 A, B, D 148.2TWU 6-1232-B Rp 2 215 140 2592.5 1816.5 776 2 1048 1048 143 A, B, D 143.2TWU 6-1232-B-SD Rp 2 215 140 2592.5 1816.5 776 2 1048 1048 143 A, B, D 143.23) For power cable in accordance with IN, max. for threaded connection
Rp
H1
H2
H
Rp
H1
H2
H
201,5
WV
R C1RC
1C2
C2
A:
B:
D:HW
-
37
Submersible pumps6" series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Wilo-Sub TWU 6-18..-B
Pump curves Wilo-Sub TWU 6-18..-B
Minimum Efficiency Index (MEI): 0.1
3~400 V, 50 Hz, p = 1 kg/dm3, v = 1x10--6 m2/s, ISO 9906 Annex A
0 2 4 6 8 10 12 14 16 18 20 22
0
0
[m/h]
[l/s]
[lgpm]
H [m]
p [%]
0
60
100
180
200
140
240
280
40
20
80
160
120
220
260
70
60
50
40
30
4
20 6040
321
10 5030 70 80
65
0 2 4 6 8 10 12 14 16 18 20 22 [m/h]
TWU 6-1818-B
TWU 6-1815-B
TWU 6-1812-B
TWU 6-1810-B
TWU 6-1808-B
TWU 6-1806-B
TWU 6-1805-B
TWU 6-1804-B
TWU 6-1803-B
TWU 6-1824-B
TWU 6-1821-B
-
38 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Wilo-Sub TWU 6-18..-B
Motor data
Wilo-Sub... Mains connection
Motor diameter
Nominal motor power
Nominal current Length of connect-ing cable
Cable cross-section
P2 IN" kW A m mm2
TWU 6-1803-B 3~400 V, 50 Hz 4 2.2 5.9 2.5 4x1,5TWU 6-1804-B 3~400 V, 50 Hz 4 3 7.8 2.5 4x1,5TWU 6-1805-B 3~400 V, 50 Hz 4 3 7.8 2.5 4x1,5TWU 6-1806-B 3~400 V, 50 Hz 4 4 10 2.5 4x1,5TWU 6-1808-B 3~400 V, 50 Hz 4 5.5 13.7 2.5 4x1,5TWU 6-1810-B 3~400 V, 50 Hz 6 7.5 16 4 4x4TWU 6-1812-B 3~400 V, 50 Hz 6 7.5 16 4 4x4TWU 6-1815-B 3~400 V, 50 Hz 6 11 23.3 4 4x4TWU 6-1818-B 3~400 V, 50 Hz 6 11 23.3 4 4x4TWU 6-1821-B 3~400 V, 50 Hz 6 15 31.3 4 4x4TWU 6-1821-B-SD 3~400 V, 50 Hz 6 15 31.3 4 2x 4x4TWU 6-1824-B 3~400 V, 50 Hz 6 15 31.3 4 4x4TWU 6-1824-B-SD 3~400 V, 50 Hz 6 15 31.3 4 2x 4x4
Information for order placements
Wilo-Sub... Mains connection Art no. Art. no. for cooling jacket pipefor vertical installation (B) for horizontal installation (D)
@TWU 6-1803-B 3~400 V, 50 Hz K 6043750 4096370 4096506TWU 6-1804-B 3~400 V, 50 Hz K 6043751 4096370 4096506TWU 6-1805-B 3~400 V, 50 Hz K 6043752 4096370 4096506TWU 6-1806-B 3~400 V, 50 Hz K 6043753 4096371 4096507TWU 6-1808-B 3~400 V, 50 Hz K 6043754 4096580 4096581TWU 6-1810-B 3~400 V, 50 Hz K 6043755 4096372 4096508TWU 6-1812-B 3~400 V, 50 Hz K 6043756 4096372 4096508TWU 6-1815-B 3~400 V, 50 Hz K 6043757 4096372 4096508TWU 6-1818-B 3~400 V, 50 Hz K 6043758 4096372 4096508TWU 6-1821-B 3~400 V, 50 Hz K 6043759 4096373 4096509TWU 6-1821-B-SD 3~400 V, 50 Hz L 6043762 4096373 4096509TWU 6-1824-B 3~400 V, 50 Hz K 6043760 4096373 4096509TWU 6-1824-B-SD 3~400 V, 50 Hz L 6043761 4096373 4096509
-
39
Submersible pumps6" series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Wilo-Sub TWU 6-18..-B
Dimension drawing Wilo-Sub TWU 6-18
A = vertical, B = vertical with cooling jacket, D = horizontal with cooling jacket
Dimensions, weights
Wilo-Sub... Pressure connec-tion
Dimensions Installa-tion
Weight approx.
C1 C2 H H1 H2 R WH WV 3) m
mm kg
TWU 6-1803-B Rp 2 150 70 886 530 356 111 589 589 143 A, B, D 37.1TWU 6-1804-B Rp 2 150 70 1080 573 507 44 656 656 143 A, B, D 42.1TWU 6-1805-B Rp 2 150 70 1123 616 507 44 656 656 143 A, B, D 44.1TWU 6-1806-B Rp 2 150 70 1242 659 583 49 816 816 143 A, B, D 53.1TWU 6-1808-B Rp 2 150 70 1442 745 697 45 930 930 143 A, B, D 62.4TWU 6-1810-B Rp 2 215 140 1508.5 862.5 646 64 911 911 143 A, B, D 84 TWU 6-1812-B Rp 2 215 140 1594.5 948.5 646 64 911 911 143 A, B, D 88 TWU 6-1815-B Rp 2 215 140 1788.5 1077.5 711 0 976 976 143 A, B, D 99.7TWU 6-1818-B Rp 2 215 140 1917.5 1206.5 711 0 976 976 143 A, B, D 105.7TWU 6-1821-B Rp 2 215 140 2261.5 1485.5 776 2 1048 1048 143 A, B, D 117.5TWU 6-1821-B-SD Rp 2 215 140 2261.5 1485.5 776 2 1048 1048 143 A, B, D 117.5TWU 6-1824-B Rp 2 215 140 2390.5 1614.5 776 2 1048 1048 143 A, B, D 123.5TWU 6-1824-B-SD Rp 2 215 140 2390.5 1614.5 776 2 1048 1048 143 A, B, D 123.53) For power cable in accordance with IN, max. for threaded connection
Rp
H1
H2
H
Rp
H1
H2
H
201,5
WV
R C1RC
1C2
C2
A:
B:
D:HW
-
40 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Wilo-Sub TWU 6-24..-B
Pump curves Wilo-Sub TWU 6-24..-B
Minimum Efficiency Index (MEI): 0.1
3~400 V, 50 Hz, p = 1 kg/dm3, v = 1x10--6 m2/s, ISO 9906 Annex A
10 12 14 16 18 20 22 24 26 28 30 [m/h]
[l/s]
[lgpm]
H [m]
p [%]
0
60
100
180
200
140
240
40
20
80
160
120
220
55
70
65
60
4
6040
3
50 70 80 10090 110
65 7 98
10 12 14 16 18 20 22 24 26 28 30 [m/h]
TWU 6-2420-B
TWU 6-2418-B
TWU 6-2415-B
TWU 6-2411-B
TWU 6-2409-B
TWU 6-2407-B
TWU 6-2405-B
TWU 6-2404-B
TWU 6-2403-B
TWU 6-2402-B
TWU 6-2413-B
-
41
Submersible pumps6" series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Wilo-Sub TWU 6-24..-B
Motor data
Wilo-Sub... Mains connection
Motor diameter
Nominal motor power
Nominal current Length of connect-ing cable
Cable cross-section
P2 IN" kW A m mm2
TWU 6-2402-B 3~400 V, 50 Hz 4 2.2 5.9 2.5 4x1,5TWU 6-2403-B 3~400 V, 50 Hz 4 3 7.8 2.5 4x1,5TWU 6-2404-B 3~400 V, 50 Hz 4 4 10 2.5 4x1,5TWU 6-2405-B 3~400 V, 50 Hz 4 5.5 13.7 2.5 4x1,5TWU 6-2407-B 3~400 V, 50 Hz 6 7.5 16 4 4x4TWU 6-2409-B 3~400 V, 50 Hz 6 11 23.3 4 4x4TWU 6-2411-B 3~400 V, 50 Hz 6 11 23.3 4 4x4TWU 6-2413-B 3~400 V, 50 Hz 6 15 31.3 4 4x4TWU 6-2413-B-SD 3~400 V, 50 Hz 6 15 31.3 4 2x 4x4TWU 6-2415-B 3~400 V, 50 Hz 6 15 31.3 4 4x4TWU 6-2415-B-SD 3~400 V, 50 Hz 6 15 31.3 4 2x 4x4TWU 6-2418-B 3~400 V, 50 Hz 6 18.5 38.5 4 4x4TWU 6-2418-B-SD 3~400 V, 50 Hz 6 18.5 38.5 4 2x 4x4TWU 6-2420-B 3~400 V, 50 Hz 6 22 45.3 4 4x4TWU 6-2420-B-SD 3~400 V, 50 Hz 6 22 45.3 4 2x 4x4
Information for order placements
Wilo-Sub... Mains connection Art no. Art. no. for cooling jacket pipefor vertical installation (B) for horizontal installation (D)
@TWU 6-2402-B 3~400 V, 50 Hz K 6043763 4096374 4096510TWU 6-2403-B 3~400 V, 50 Hz K 6043764 4096374 4096510TWU 6-2404-B 3~400 V, 50 Hz K 6043765 4096375 4096511TWU 6-2405-B 3~400 V, 50 Hz K 6043766 4096376 4096512TWU 6-2407-B 3~400 V, 50 Hz K 6043767 4096572 4096574TWU 6-2409-B 3~400 V, 50 Hz K 6043768 4096573 4096575TWU 6-2411-B 3~400 V, 50 Hz K 6043769 4096573 4096575TWU 6-2413-B 3~400 V, 50 Hz K 6043770 4096573 4096575TWU 6-2413-B-SD 3~400 V, 50 Hz L 6043774 4096573 4096575TWU 6-2415-B 3~400 V, 50 Hz L 6043771 4096573 4096575TWU 6-2415-B-SD 3~400 V, 50 Hz K 6043775 4096573 4096575TWU 6-2418-B 3~400 V, 50 Hz K 6043772 4096377 4096513TWU 6-2418-B-SD 3~400 V, 50 Hz L 6043776 4096377 4096513TWU 6-2420-B 3~400 V, 50 Hz K 6043773 4096378 4096514TWU 6-2420-B-SD 3~400 V, 50 Hz K 6043777 4096378 4096514
-
42 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Wilo-Sub TWU 6-24..-B
Dimension drawing Wilo-Sub TWU 6-24
A = vertical, B = vertical with cooling jacket, D = horizontal with cooling jacket
Dimensions, weights
Wilo-Sub... Pressure connec-tion
Dimensions Installa-tion
Weight approx.
C1 C2 H H1 H2 R WH WV W2 3) m
mm kg
TWU 6-2402-B Rp 2 150 70 867 511 356 99 601 601 143 A, B, D 34.1TWU 6-2403-B Rp 2 150 70 1073 566 507 32 668 668 143 A, B, D 39.6TWU 6-2404-B Rp 2 150 70 1204 621 583 37 828 828 143 A, B, D 49.1TWU 6-2405-B Rp 2 150 70 1373 676 697 33 942 942 143 A, B, D 56.9TWU 6-2407-B Rp 2 215 140 1463.5 817.5 646 52 923 923 143 A, B, D 80.5TWU 6-2409-B Rp 2 215 140 1638.5 927.5 711 62 988 988 143 A, B, D 91.2TWU 6-2411-B Rp 2 215 140 1748.5 1037.5 711 62 988 988 143 A, B, D 96.2TWU 6-2413-B Rp 2 215 140 1923.5 1147.5 776 0 1053 1053 143 A, B, D 107 TWU 6-2413-B-SD Rp 2 215 140 1923.5 1147.5 776 0 1053 1053 143 A, B, D 107 TWU 6-2415-B Rp 2 215 140 2033.5 1257.5 776 0 1053 1053 143 A, B, D 112 TWU 6-2415-B-SD Rp 2 215 140 2033.5 1257.5 776 0 1053 1053 143 A, B, D 112 TWU 6-2418-B Rp 2 215 140 2264.5 1422.5 842 50 1120 1120 600 143 A, B, D 126.1TWU 6-2418-B-SD Rp 2 215 140 2264.5 1422.5 842 50 1120 1120 600 143 A, B, D 126.1TWU 6-2420-B Rp 2 215 140 2439.5 1532.5 907 50 1184 1184 600 143 A, B, D 138.6TWU 6-2420-B-SD Rp 2 215 140 2439.5 1532.5 907 50 1184 1184 600 143 A, B, D 138.63) For power cable in accordance with IN, max. for threaded connection
Rp
H1
H2
H
Rp
H1
H2
H
201,5
201,5
WV WH
W2
R C1
RRR C1
C1 C1
C2
C 2
C2
C2
WV
W2
A:
B:
D:HW
-
43
Submersible pumps6" series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Wilo-Sub TWU 6-35..-B
Pump curves Wilo-Sub TWU 6-35..-B
Minimum Efficiency Index (MEI): 0.1
3~400 V, 50 Hz, p = 1 kg/dm3, v = 1x10--6 m2/s, ISO 9906 Annex A
10 14 18 22 26 30 34 38 42 46 [m/h]
[l/s]
[lgpm]
H [m]
p [%]
0
60
100
140
160
40
20
80
120
40
70
60
50
6040
3
80 100 120 140 160
654 7 98 10 11 1312
10 14 18 22 26 30 34 38 42 46 [m/h]
TWU 6-3514-B
TWU 6-3512-B
TWU 6-3510-B
TWU 6-3507-B
TWU 6-3506-B
TWU 6-3504-B
TWU 6-3517-B
TWU 6-3503-B
-
44 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Wilo-Sub TWU 6-35..-B
Motor data
Wilo-Sub... Mains connection
Motor diameter
Nominal motor power
Nominal current Length of connect-ing cable
Cable cross-section
P2 IN" kW A m mm2
TWU 6-3503-B 3~400 V, 50 Hz 4 3 7.8 2.5 4x1,5TWU 6-3504-B 3~400 V, 50 Hz 4 4 10 2.5 4x1,5TWU 6-3506-B 3~400 V, 50 Hz 6 7.5 16 4 4x4TWU 6-3507-B 3~400 V, 50 Hz 6 7.5 16 4 4x4TWU 6-3510-B 3~400 V, 50 Hz 6 11 23.3 4 4x4TWU 6-3512-B 3~400 V, 50 Hz 6 15 31.3 4 4x4TWU 6-3512-B-SD 3~400 V, 50 Hz 6 15 31.3 4 2x 4x4TWU 6-3514-B 3~400 V, 50 Hz 6 15 31.3 4 4x4TWU 6-3514-B-SD 3~400 V, 50 Hz 6 15 31.3 4 2x 4x4TWU 6-3517-B 3~400 V, 50 Hz 6 18.5 38.5 4 4x4TWU 6-3517-B-SD 3~400 V, 50 Hz 6 18.5 38.5 4 2x 4x4
Information for order placements
Wilo-Sub... Mains connection Art no. Art. no. for cooling jacket pipefor vertical installation (B) for horizontal installation (D)
@TWU 6-3503-B 3~400 V, 50 Hz K 6043778 4096379 4096515TWU 6-3504-B 3~400 V, 50 Hz K 6043779 4096380 4096516TWU 6-3506-B 3~400 V, 50 Hz K 6043780 4096381 4096517TWU 6-3507-B 3~400 V, 50 Hz K 6043781 4096381 4096517TWU 6-3510-B 3~400 V, 50 Hz K 6043782 4096381 4096517TWU 6-3512-B 3~400 V, 50 Hz K 6043783 4096382 4096518TWU 6-3512-B-SD 3~400 V, 50 Hz L 6043786 4096382 4096518TWU 6-3514-B 3~400 V, 50 Hz K 6043784 4096382 4096518TWU 6-3514-B-SD 3~400 V, 50 Hz K 6043787 4096382 4096518TWU 6-3517-B 3~400 V, 50 Hz K 6043785 4096383 4096520TWU 6-3517-B-SD 3~400 V, 50 Hz L 6043788 4096383 4096520
-
45
Submersible pumps6" series
Subm
ersi
ble
pum
ps
Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Wilo-Sub TWU 6-35..-B
Dimension drawing Wilo-Sub TWU 6-35
A = vertical, B = vertical with cooling jacket, D = horizontal with cooling jacket
Dimensions, weights
Wilo-Sub... Pressure connec-tion
Dimensions Installa-tion
Weight approx.
C1 C2 H H1 H2 R WH WV W2 3) m
mm kg
TWU 6-3503-B Rp 2 150 70 1062 555 507 59 641 641 143 A, B, D 39.1TWU 6-3504-B Rp 2 150 70 1228 645 583 64 801 801 143 A, B, D 50.6TWU 6-3506-B Rp 2 215 140 1522 825 697 98 877 877 143 A, B, D 64.9TWU 6-3507-B Rp 2 215 140 1592.5 946.5 646 87 888 888 143 A, B, D 85.5TWU 6-3510-B Rp 2 215 140 1927.5 1216.5 711 22 953 953 143 A, B, D 100.2TWU 6-3512-B Rp 2 215 140 2172.5 1396.5 776 32 1018 1018 143 A, B, D 115 TWU 6-3512-B-SD Rp 2 215 140 2172.5 1396.5 776 32 1018 1018 143 A, B, D 115 TWU 6-3514-B Rp 2 215 140 2352.5 1576.5 776 32 1018 1018 143 A, B, D 124 TWU 6-3514-B-SD Rp 2 215 140 2352.5 1576.5 776 32 1018 1018 143 A, B, D 124 TWU 6-3517-B Rp 2 215 140 2688.5 1846.5 842 50 1084 1084 600 143 A, B, D 144.1TWU 6-3517-B-SD Rp 2 215 140 2688.5 1846.5 842 50 1084 1084 600 143 A, B, D 144 3) For power cable in accordance with IN, max. for threaded connection
Rp
H1
H2
H
Rp
H1
H2
H
201,5
201,5
WV WH
W2
R C1
RRR C1
C1 C1
C2
C 2C2
C2
WV
W2
A:
B:
D:HW
-
46 Wilo water management catalogue 50 Hz Water supply Raw water intake edition 2014/2015 Subject to change without prior notice
Submersible pumps6" series
Wilo-Sub TWU 6-45..-B
Pump curves Wilo-Sub TWU 6-45..-B
Minimum Efficiency Index (MEI): 0.1
3~400 V, 50 Hz, p = 1 kg/dm3, v = 1x10--6 m2/s, ISO 9906 Annex A
30 34 38 42 46 50 54 58 62 66 [m/h]
[l/s]
[lgpm]
H [m]
p [%]
0
60
100
140
160
40
20
80
120
30
40
70
60
50
120 140 160 180 200 220 240
1311109 12 1817 191514 16
30 34 38 42 46 50 54 58 62 66 [m/h]
TWU 6-4516-B
TWU 6-4514-B
TWU 6-4512-B
TWU 6-4510-B
TWU 6-4508-B
TWU 6-4506-B
TWU 6-4505-B
TWU 6-4504-B
TWU 6-4503-B
-
47
Submersible pumps6" series
Subm
ersi
ble