Daikin Water Chillers are of the self-contained type. This means that they are assembled, internally wired and charged with refrigerant at the factory for easy installation, only requiring external wiring and plumbing on site. They are compatible with Daikin's Air Handling and/or Fan Coil Units.

All rights reservedPrinted in Japan 11/06/005 SW.HP.ADc

DealerHead Office:Umeda Center Bldg., 2-4-12, Nakazaki-Nishi,Kita-ku, Osaka, 530-8323 Japan

Tokyo Office:JR Shinagawa East Bldg., 2-18-1, Konan,Minato-ku, Tokyo, 108-0075 Japan

http://www.daikin.com/global/

1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided and choose an outdoor unit with anti-corrosion treatment.

Cautions on product corrosion

Warning Daikin Industries, Ltd.’s products are manufactured for export to numerous countries throughout the world. Daikin Industries, Ltd. does not have control over which products are exported to and used in a particular country. Prior to purchase, please therefore confirm with your local authorised importer, distributor and/or retailer whether this product conforms to the applicable standards, and is suitable for use, in the region where the product will be used. This statement does not purport to exclude, restrict or modify the application of any local legislation.Ask a qualified installer or contractor to install this product. Do not try to install the product yourself. Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion.Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or contractor to install those parts and accessories. Use of unauthorised parts and accessories or improper installation of parts and accessories can result in water or refrigerant leakage, electrical shock, fire or explosion.Read the User's Manual carefully before using this product. The User's Manual provides important safety instructions and warnings. Be sure to follow these instructions and warnings.

If you have any enquiries, please contact your local importer, distributor and/or retailer.

Printed on 100% recycled paper with soy ink.Specifications, designs and other content appearing in this brochure are current as of November 2006 but subject to change without notice.

ISO 14001 is the standard defined by the International Organization for Standardization (ISO) relating to environmental management systems. Our group has been acknowledged by an internationally accredited compliance organisation as having an appropriate programme of environmental protection procedures and activities to meet the requirements of ISO 14001.

About ISO 14001ISO 9001 is a plant certification system defined by the International Organization for Standardization (ISO) relating to quality assurance. ISO 9001 certification covers quality assurance aspects related to the “ design, development, manufacture, installation, and supplementary service” of products manufactured at the plant.

About ISO9001

JMI-0107 EC99J2044

2

H ig h -pe r fo r m a n c e D a ik in W a t e r C h i l le r s a r e A v a i la ble in a B r o a d R a n g e o f M o de ls t o S u it D iv e r s e A ppl ic a t io n s .

Lis t of Daikin Water C hiller Models

1 2

Air Cooled Water Chillers : UWAP S eries / UWAXP S eries : UWA S eries / ( For High Outdoor Temperature Use )

Dedicated water chillers are able to operate year round because they can accommodate a wide range of outdoor temperatures. The high-performance models with capacities of over 40 HP can deliver between 10% (12% ) and 100% of their capacities. They are able to withstand the demanding conditions typical of industrial applications.

Air Cooled Water Chillers - Heat Pump Type

Water Cooled Water Chillers

Air cooled heat pump system units are an ideal way to provide a reliable supply of hot and cold water. Of compact s ize because no cooling tower is required, they are also suitable for office building air conditioning. These high-end models provide an answer to a variety of air conditioning requirements.

Water cooled units provide a s table supply of chilled water year round and are unaffected by changes in the outdoor temperature. In addition to air conditioning applications , they are also a highly reliable industrial process cooling solution thanks to their s tability and wide temperature control range.

Air Cooled Water Chillers

Air

Coo

led

Wat

er C

hill

ers20 40 60 80 100 150 200 250 300 350 450 500 600 700 800 900 1000 1200 1400 P age

11

12 13

14

14 15

17

18

21

21 22

23

27

27

28

29

9 10

9

C apac ity R ange (kW)

Air Cooled Water Chillers - Heat Pump Type

Water Cooled Water Chillers

Standard Unit

Standard Unit

Standard Unit

Brine Cooling Unit

Standard Unit

ForHigh Outdoor Temperature Use

Standard Unit

Inverter Cooling Unit

Brine Cooling Unit

Year - Round Cooling Only Unit

Standard Unit

Air Cooled Water Chillers20 40 60 80 100 150 200 250 300 350 450 500 600 700 800 900 1000 1200 1400 P age

12

13

15

18

21

22

24

27

28

29

10

9

C apac ity R ange (kW)

Air Cooled Water Chillers - Heat Pump Type

Water Cooled Water Chillers

Standard Unit

Standard Unit

Standard Unit

Brine Cooling Unit

Standard Unit

For High Outdoor Temperature Use

Standard Unit

Brine Cooling Unit

Year - Round Cooling Only Unit

Standard Unit

Wat

er C

oole

d W

ater

Chi

ller

sA

ir C

oole

d W

ater

Chi

ller

s- H

eat P

ump

Type

: UWY P S eries : UWY S eries

: UWP S eries : UWD S eries ZUW S eries

50Hz

60Hz

106 1260 UWAP-BY1

106 1260 UWAP-BY1K

12.5 75

11.2 67

106 1260 UWA-AY1

106 1260 UWYP-BY1

106 1260 UWY-AY1

8 80

118 355 UWD-DY1

UWAXP-AY1

108.4 319.2 UWA-JAY1

351.6 791 UWA-JY1

UWP-AY3

6.7 67 UWAP-AY3

68 808 UWAP-BY1Z

UWYP-AY3

367 1450 ZUW-AY1

190 715 ZUW-AY1Z

118 355 UWAP-BYB

118 355 UWAP-BYBK

118 355 UWYP-BYB

118 355 UWY-AYB

9 90 UWP-AY3

79 370 UWA-JATJ

7.5 75 UWAP-AY3

79 242

118 355 UWA-AYB

UWYP-AY312.5 75

441 1040 ZUW-AYB

233 555 ZUW-AYBZ

UWAP-BYBZ

Daikin chilling units employ advanced technology that provides highly accurate temperature control to within 0.5 . They are widely used in applications ranging from air conditioning to industrial equipment. Recent changes have introduced new models with substantially increased capacities of up to 480 HP and various model series, including advanced inverter type units, year-round cooling type units, and units with brine-resistant specifications. By providing a full lineup of heat source series choices, Daikin offers an even more flexible array of solutions for a wide range of heat source applications.

2

H ig h -pe r fo r m a n c e D a ik in W a t e r C h i l le r s a r e A v a i la ble in a B r o a d R a n g e o f M o de ls t o S u it D iv e r s e A ppl ic a t io n s .

Lis t of Daikin Water C hiller Models

1 2

Air Cooled Water Chillers : UWAP S eries / UWAXP S eries : UWA S eries / ( For High Outdoor Temperature Use )

Dedicated water chillers are able to operate year round because they can accommodate a wide range of outdoor temperatures. The high-performance models with capacities of over 40 HP can deliver between 10% (12% ) and 100% of their capacities. They are able to withstand the demanding conditions typical of industrial applications.

Air Cooled Water Chillers - Heat Pump Type

Water Cooled Water Chillers

Air cooled heat pump system units are an ideal way to provide a reliable supply of hot and cold water. Of compact s ize because no cooling tower is required, they are also suitable for office building air conditioning. These high-end models provide an answer to a variety of air conditioning requirements.

Water cooled units provide a s table supply of chilled water year round and are unaffected by changes in the outdoor temperature. In addition to air conditioning applications , they are also a highly reliable industrial process cooling solution thanks to their s tability and wide temperature control range.

Air Cooled Water Chillers

Air

Coo

led

Wat

er C

hill

ers20 40 60 80 100 150 200 250 300 350 450 500 600 700 800 900 1000 1200 1400 P age

11

12 13

14

14 15

17

18

21

21 22

23

27

27

28

29

9 10

9

C apac ity R ange (kW)

Air Cooled Water Chillers - Heat Pump Type

Water Cooled Water Chillers

Standard Unit

Standard Unit

Standard Unit

Brine Cooling Unit

Standard Unit

ForHigh Outdoor Temperature Use

Standard Unit

Inverter Cooling Unit

Brine Cooling Unit

Year - Round Cooling Only Unit

Standard Unit

Air Cooled Water Chillers20 40 60 80 100 150 200 250 300 350 450 500 600 700 800 900 1000 1200 1400 P age

12

13

15

18

21

22

24

27

28

29

10

9

C apac ity R ange (kW)

Air Cooled Water Chillers - Heat Pump Type

Water Cooled Water Chillers

Standard Unit

Standard Unit

Standard Unit

Brine Cooling Unit

Standard Unit

For High Outdoor Temperature Use

Standard Unit

Brine Cooling Unit

Year - Round Cooling Only Unit

Standard Unit

Wat

er C

oole

d W

ater

Chi

ller

sA

ir C

oole

d W

ater

Chi

ller

s- H

eat P

ump

Type

: UWY P S eries : UWY S eries

: UWP S eries : UWD S eries ZUW S eries

50Hz

60Hz

106 1260 UWAP-BY1

106 1260 UWAP-BY1K

12.5 75

11.2 67

106 1260 UWA-AY1

106 1260 UWYP-BY1

106 1260 UWY-AY1

8 80

118 355 UWD-DY1

UWAXP-AY1

108.4 319.2 UWA-JAY1

351.6 791 UWA-JY1

UWP-AY3

6.7 67 UWAP-AY3

68 808 UWAP-BY1Z

UWYP-AY3

367 1450 ZUW-AY1

190 715 ZUW-AY1Z

118 355 UWAP-BYB

118 355 UWAP-BYBK

118 355 UWYP-BYB

118 355 UWY-AYB

9 90 UWP-AY3

79 370 UWA-JATJ

7.5 75 UWAP-AY3

79 242

118 355 UWA-AYB

UWYP-AY312.5 75

441 1040 ZUW-AYB

233 555 ZUW-AYBZ

UWAP-BYBZ

Daikin chilling units employ advanced technology that provides highly accurate temperature control to within 0.5 . They are widely used in applications ranging from air conditioning to industrial equipment. Recent changes have introduced new models with substantially increased capacities of up to 480 HP and various model series, including advanced inverter type units, year-round cooling type units, and units with brine-resistant specifications. By providing a full lineup of heat source series choices, Daikin offers an even more flexible array of solutions for a wide range of heat source applications.

E quipped with an E fficient, Durable S emi-hermetically S ealed S crew C ompressor.

60,000Sales volume

Gate Rotor

ScrewRotor Suction

Pressure

SuctionPressure

Discharge Pressure

Discharge Pressure

E quipped with a Newly Developed, Highly E ffic ient C ompac t C ompres s or.Optimization of the unit enhances efficient operation. A newly developed denture mold enabled the production of a compact model with reduced volume and weight.

High Operational E ffic ienc y R educ es E nergy Los s .In addition to effic ient operation afforded by a 12-compress ion s ingle cycle, the s ingle screw construction eliminates blow-by from high to low pressure sections to reduce energy loss . Daikin water chillers are equipped with a tightly sealed gate rotor to reduce refrigerant loss from leakage. Our compressors are des igned for efficient operation

High Ac c urac y and High Durability.C areful construction features gate rotors pos itioned to the right and left of the screw to eliminate eccentric load produced by pressure differential. The orthogonal rotor shaft uses high-precis ion ball and roller bearings , which extends its life compared to conventional types . In addition, power transmiss ion between rotors is reduced, thus eliminating friction wear and maintaining stable operating performance over an extended period of time.

Low Vibration and S ound Levels .Daikin water chillers us e gate rotors made of high-performance engineering plastic for smooth meshing with the screw rotor, thereby reducing shock and vibration. while maintaining stable operation. The gate rotors are well balanced to equalize pressure, which reduces noise and

L ightweight C ompac t Des ign S ave S pac e.In addition to the s imple s ingle rotor construction, the compact, lightweight des ign eliminates the need for an oil cooler while incorporating the oil separator into a s ingle part to reduce the space required for setup.

Durable C ons truc tion Inc reas es Ins pec tion Intervals thereby Dec reas ing Maintenanc e.Durability of the equipment increases the maintenance interval to approximately 40,000 hours (or about seven years ). The s implified lubrication system, including a high/low pressure differential lubrication system and ball and roller bearings , reduces the factors that can contribute to problems. Along with increas ing the maintenance and inspection interval, the careful construction of Daikin water chillers enhances reliability.

C as ingS crew rotorS lide valveB all bearingMotorG ate rotorHigh efficient oil separatorHigh-low pressure differential lubricating mechanismB earing lubricating oil for models us ing new refrigerantR efrigerant inletR efrigerant outlet

1

2

3

4

5

6

7

8

9

10

11

12

4

5

63

8

9

7

10

11

High Function Microcomputer C ontrol P anel and Multifunctional R emote C ontroller R ealise E fficient Operation C ontrol.

S imple key operation displays required operating and settings data. Displays a complete of operating data for easy comprehension.

Up to eight units c an be group c ontrolled by a s ingle remote c ontroller.E quipped with s imultaneous defros t prevention c ontrol for avoiding radic al water temperature c hange when operating multiple units .*S imultaneous defrost can be carried out for up to two units when five or more units are connected.

Note : C ustom orders may take more time for delivery.

R otation c ontrol

Mic roc omputer C ontrol P anel Makes Operation C ontrol E as y.

Multi-display

Controls Multiple Units Effectively

A Multifunc tional L iquid C rys tal R emote C ontroller for E ffec tive G roup C ontrol.

Function for Equal Control using Microcomputer Control Panel

E nables different types of remote control, such as control by commands from the host computer, the Daikin B uilding Air-C onditioning C ontrol S ystem (D-B AC S ), or the multifunctional remote controller.

Remote Control by Remote Command

On/Off remote c ontrol

R emote s etting of water temperature

S etting for heat s torage operationY ou can s witch s ettings from normal operation to either temperature setting for heat s torage or control by the external

Lower nois e operation for during nighttimeY ou can reduce the operating noise by stopping half the fan. Note that the capacity control of the chiller should be limited to less than 70% .

Forc ed fan operation c ontrol*Y ou can force fan operation even when the unit is s topped, which is convenient for removing the snow collected on the fan.*This function is des igned for in areas where snow rarely falls . An optional snow hood should be used in areas prone to snow.

Demand c ontrol(1) Y ou can have Three demand controls are poss ible thermostat Off, less than 40% or less than 70% . (Factory set:70% )(2) Demand control may also be achieved by setting the operating current of the compressor.*Demand control is available on all models , with the exception of those lis ted below.UWAP 75 — 750AY 3, UWAXP 125 — 750AY 1, UWA37 — 109J AY 1, UWA120 — 270J Y 1, UWA27 — 122J ATJ , UWY P 125 — 750AY 3,UWP 90 — 900AY 3

Outdoor temperature

Inlet/Outlet temperature

Dis c harge gas temperature

Dis plays operating data for eas y c omprehens ion of s ys tem s tatus .

High and low pres s ure

Water temperature s etting

Malfunc tion c ode

*For details , refer to the Operation Manual of each model.

On/Off c ontrol

Water temperature s etting

S witc hing of operatingmode

Defros t c yc le s etting*

Heat s torage operation

E nables different types of remote c ontrol.

Low nois e operation duringnighttime

Forc ed fan operation

Demand c ontrol*

R otation c ontrol

Ins pec tion/Tes t operation

Memorizes the number of s tops for each unit (therefore not effective for systems in continuous operation), and smooths operation by starting in order from the unit with the least number of s tarts and stops to increase the life time of all apparatus in the system.

B R C 307 (Option)

*Applies to all models , with the exc eption of thos e lis ted below.UWA37 — 109J AY 1, UWA120 — 270J Y 1, UWA27 — 122J ATJ , UWP 90 — 900AY 3

*Demand control is not available with

*Applies to heat-pump type only.

Outdoor temp.

Discharge gas temp.

Water temp. setting

Inlet/outlet water temp.

H/L pressure of refrigerant

Centralized control

Malfunction code display

3 4

E quipped with an E fficient, Durable S emi-hermetically S ealed S crew C ompressor.

60,000Sales volume

Gate Rotor

ScrewRotor Suction

Pressure

SuctionPressure

Discharge Pressure

Discharge Pressure

E quipped with a Newly Developed, Highly E ffic ient C ompac t C ompres s or.Optimization of the unit enhances efficient operation. A newly developed denture mold enabled the production of a compact model with reduced volume and weight.

High Operational E ffic ienc y R educ es E nergy Los s .In addition to effic ient operation afforded by a 12-compress ion s ingle cycle, the s ingle screw construction eliminates blow-by from high to low pressure sections to reduce energy loss . Daikin water chillers are equipped with a tightly sealed gate rotor to reduce refrigerant loss from leakage. Our compressors are des igned for efficient operation

High Ac c urac y and High Durability.C areful construction features gate rotors pos itioned to the right and left of the screw to eliminate eccentric load produced by pressure differential. The orthogonal rotor shaft uses high-precis ion ball and roller bearings , which extends its life compared to conventional types . In addition, power transmiss ion between rotors is reduced, thus eliminating friction wear and maintaining stable operating performance over an extended period of time.

Low Vibration and S ound Levels .Daikin water chillers us e gate rotors made of high-performance engineering plastic for smooth meshing with the screw rotor, thereby reducing shock and vibration. while maintaining stable operation. The gate rotors are well balanced to equalize pressure, which reduces noise and

L ightweight C ompac t Des ign S ave S pac e.In addition to the s imple s ingle rotor construction, the compact, lightweight des ign eliminates the need for an oil cooler while incorporating the oil separator into a s ingle part to reduce the space required for setup.

Durable C ons truc tion Inc reas es Ins pec tion Intervals thereby Dec reas ing Maintenanc e.Durability of the equipment increases the maintenance interval to approximately 40,000 hours (or about seven years ). The s implified lubrication system, including a high/low pressure differential lubrication system and ball and roller bearings , reduces the factors that can contribute to problems. Along with increas ing the maintenance and inspection interval, the careful construction of Daikin water chillers enhances reliability.

C as ingS crew rotorS lide valveB all bearingMotorG ate rotorHigh efficient oil separatorHigh-low pressure differential lubricating mechanismB earing lubricating oil for models us ing new refrigerantR efrigerant inletR efrigerant outlet

1

2

3

4

5

6

7

8

9

10

11

12

4

5

63

8

9

7

10

11

High Function Microcomputer C ontrol P anel and Multifunctional R emote C ontroller R ealise E fficient Operation C ontrol.

S imple key operation displays required operating and settings data. Displays a complete of operating data for easy comprehension.

Up to eight units c an be group c ontrolled by a s ingle remote c ontroller.E quipped with s imultaneous defros t prevention c ontrol for avoiding radic al water temperature c hange when operating multiple units .*S imultaneous defrost can be carried out for up to two units when five or more units are connected.

Note : C ustom orders may take more time for delivery.

R otation c ontrol

Mic roc omputer C ontrol P anel Makes Operation C ontrol E as y.

Multi-display

Controls Multiple Units Effectively

A Multifunc tional L iquid C rys tal R emote C ontroller for E ffec tive G roup C ontrol.

Function for Equal Control using Microcomputer Control Panel

E nables different types of remote control, such as control by commands from the host computer, the Daikin B uilding Air-C onditioning C ontrol S ystem (D-B AC S ), or the multifunctional remote controller.

Remote Control by Remote Command

On/Off remote c ontrol

R emote s etting of water temperature

S etting for heat s torage operationY ou can s witch s ettings from normal operation to either temperature setting for heat s torage or control by the external

Lower nois e operation for during nighttimeY ou can reduce the operating noise by stopping half the fan. Note that the capacity control of the chiller should be limited to less than 70% .

F orc ed fan operation c ontrol*Y ou can force fan operation even when the unit is s topped, which is convenient for removing the snow collected on the fan.*This function is des igned for in areas where snow rarely falls . An optional snow hood should be used in areas prone to snow.

Demand c ontrol(1) Y ou can have Three demand controls are poss ible thermostat Off, less than 40% or less than 70% . (Factory set:70% )(2) Demand control may also be achieved by setting the operating current of the compressor.*Demand control is available on all models , with the exception of those lis ted below.UWAP 75 — 750AY 3, UWAXP 125 — 750AY 1, UWA37 — 109J AY 1, UWA120 — 270J Y 1, UWA27 — 122J ATJ , UWY P 125 — 750AY 3,UWP 90 — 900AY 3

Outdoor temperature

Inlet/Outlet temperature

Dis c harge gas temperature

Dis plays operating data for eas y c omprehens ion of s ys tem s tatus .

High and low pres s ure

Water temperature s etting

Malfunc tion c ode

*For details , refer to the Operation Manual of each model.

On/Off c ontrol

Water temperature s etting

S witc hing of operatingmode

Defros t c yc le s etting*

Heat s torage operation

E nables different types of remote c ontrol.

Low nois e operation duringnighttime

F orc ed fan operation

Demand c ontrol*

R otation c ontrol

Ins pec tion/Tes t operation

Memorizes the number of s tops for each unit (therefore not effective for systems in continuous operation), and smooths operation by starting in order from the unit with the least number of s tarts and stops to increase the life time of all apparatus in the system.

B R C 307 (Option)

*Applies to all models , with the exc eption of thos e lis ted below.UWA37 — 109J AY 1, UWA120 — 270J Y 1, UWA27 — 122J ATJ , UWP 90 — 900AY 3

*Demand control is not available with

*Applies to heat-pump type only.

Outdoor temp.

Discharge gas temp.

Water temp. setting

Inlet/outlet water temp.

H/L pressure of refrigerant

Centralized control

Malfunction code display

3 4

Daikin's C ontrol S ystem for C entral Air C onditioning S ystem Offers Appropriate C ontrol for Use and S ize of B uilding.

Daikin's intelligent control solution for the whole air-conditioning system.

Daikin's Control System for Central Air Conditioning.

Daikin introduces its "C ontrol S ystem for C entral Air C onditioning" The system lets you freely combine a number of optional controllers for centralized control to construct the air conditioning control system that is appropriate for your needs . The system executes total central control of chillers and air conditioners , to save management labour while realizing ideal central air conditioning performance.

Different C ontrol Apparatus C ombinations E nable a Multipurpos e S ys tem.Daikin offers a lineup of c entral controllers equipped with a variety of functions . The unified ON/OFF controller lets you turn equipment on and off individually or in groups . The schedule timer lets you program the time for connected equipment to be turned on and off for eac h week. C ontrol apparatus with different functions can be freely combined, and up to 64 groups can be centrally controlled.*Number of units that c an be

Note:The system shown above is applicable only to Series UWAJ-G, UWYJ-B, UWAP-G and UWYP-G.Note:Air handling and Fan coil units can be connected by custom orders.

C entral remote controller Unified ON/OFF controller S chedule timer

Model

S top-running c ommandC ooling/heating mode settingTemp. settingS c hedule func tionInterloc k settingPower proportion limitationS top-runningC ooling/heating modeTemperature setR oom temp. (suc tion inlet)Water temp. (inlet/outlet)AbnormalAbnormal s ignalFilter s ignalC ontinuous running periodTemp. upper/lower limit

S tandard c onnec tion

Air-c ooling Unit

UWAP,UWYP,UWA,UWY

Water-c ooling Unit

ZUW

AIR NE T

DioUnit

C ommodity from other c ompanies

Pump, R efrigerating Unit, C ooling Tower

(Note1)

System Structure(VRV+central conditioning)

C ool/warm water pump 1C ooling tower 1

iPU(R eservedfor VR V)

E themet

VR V(4 ports )256 indoor units

Dio Unit Dio Unit

Wiring adaptor is required for c onnec ting Dio unit to Airnet

1. C entral air-c onditioning system c an be c ontrolled together with VR V.

2. Operating interfac e is based on the windows interfac e, whic h is easy to use.

3. 1024 units (groups) of indoor unit or water c ooled c hiller c an be c onnec ted.

4. Power distribution in proportions , c alc ulation the power rate and other AC -related c osts of user.

5. C an be c onnec ted with Air C onditioning Network S ervic e S ystem

6. Ordinary 2-c ore c able is used for wiring, the field wiring work is very s imple.

Features of I-Manager

( realised func tion irrespec tive item only data information, c an't be ac hieved up till now)

Note1: C an realize partial func tion of Air C onditioning Network S ervic e S ystem.

* Please contact Daikin for detailed data for connection of Fan coil and AC(terminal products)

R emote c ontroller(units No. c ontrol)

C ool/warm water pump 3

Monitoring func tion

C ontrollingfunc tion

Func tion

R emote monitor c enter

Max. 4 iPUs are

iPU(R eserved for c entral

air-c onditioning system)

E quipment~pump of other c ompany, c ooling tower(1

port) Pump 4 units

Note: It is not poss ible to c onnec t a high outdoor temperature spec ific ation unit and the UWAP75 — 750.

D -NE T

I-Manager

D -NE T

D -NE T wiring adaptor

Water c ooled c hiller (1 port)Air-c ooling 240HP 2 units

Water-c ooling 400US R T 1 unit

Unified ON/OFF controller

Chilling unit

Possible to link withhost computer

Schedule timer

SkyAir series

VRV system

Central remote controllerPossible to have a forcedshut-down input

Enables control of other air conditioning systemssuch as VRV, SkyAir or HRV.

Enables individual control from chillers to air conditioners by using a single line.

Enables group control by remote controllers of both chillers and air conditioners.

Lets you develop a system that doesn't use individual remote controllers.(Central remote controller required)

Air handling unit Air handling unit Fan coil unit Possiblewireless remote controller

System configuration

D adaptor I-Manager option

Control Function List of I-Manager

I-Manager Control heat resources system by using I-Manager

New VersionNew Version

5 6

Daikin's C ontrol S ystem for C entral Air C onditioning S ystem Offers Appropriate C ontrol for Use and S ize of B uilding.

Daikin's intelligent control solution for the whole air-conditioning system.

Daikin's Control System for Central Air Conditioning.

Daikin introduces its "C ontrol S ystem for C entral Air C onditioning" The system lets you freely combine a number of optional controllers for centralized control to construct the air conditioning control system that is appropriate for your needs . The system executes total central control of chillers and air conditioners , to save management labour while realizing ideal central air conditioning performance.

Different C ontrol Apparatus C ombinations E nable a Multipurpos e S ys tem.Daikin offers a lineup of c entral controllers equipped with a variety of functions . The unified ON/OFF controller lets you turn equipment on and off individually or in groups . The schedule timer lets you program the time for connected equipment to be turned on and off for eac h week. C ontrol apparatus with different functions can be freely combined, and up to 64 groups can be centrally controlled.*Number of units that c an be

Note:The system shown above is applicable only to Series UWAJ-G, UWYJ-B, UWAP-G and UWYP-G.Note:Air handling and Fan coil units can be connected by custom orders.

C entral remote controller Unified ON/OFF controller S chedule timer

Model

S top-running c ommandC ooling/heating mode settingTemp. settingS c hedule func tionInterloc k settingPower proportion limitationS top-runningC ooling/heating modeTemperature setR oom temp. (suc tion inlet)Water temp. (inlet/outlet)AbnormalAbnormal s ignalFilter s ignalC ontinuous running periodTemp. upper/lower limit

S tandard c onnec tion

Air-c ooling Unit

UWAP,UWYP,UWA,UWY

Water-c ooling Unit

ZUW

AIR NE T

DioUnit

C ommodity from other c ompanies

Pump, R efrigerating Unit, C ooling Tower

(Note1)

System Structure(VRV+central conditioning)

C ool/warm water pump 1C ooling tower 1

iPU(R eservedfor VR V)

E themet

VR V(4 ports )256 indoor units

Dio Unit Dio Unit

Wiring adaptor is required for c onnec ting Dio unit to Airnet

1. C entral air-c onditioning system c an be c ontrolled together with VR V.

2. Operating interfac e is based on the windows interfac e, whic h is easy to use.

3. 1024 units (groups) of indoor unit or water c ooled c hiller c an be c onnec ted.

4. Power distribution in proportions , c alc ulation the power rate and other AC -related c osts of user.

5. C an be c onnec ted with Air C onditioning Network S ervic e S ystem

6. Ordinary 2-c ore c able is used for wiring, the field wiring work is very s imple.

Features of I-Manager

( realised func tion irrespec tive item only data information, c an't be ac hieved up till now)

Note1: C an realize partial func tion of Air C onditioning Network S ervic e S ystem.

* Please contact Daikin for detailed data for connection of Fan coil and AC(terminal products)

R emote c ontroller(units No. c ontrol)

C ool/warm water pump 3

Monitoring func tion

C ontrollingfunc tion

Func tion

R emote monitor c enter

Max. 4 iPUs are

iPU(R eserved for c entral

air-c onditioning system)

E quipment~pump of other c ompany, c ooling tower(1

port) Pump 4 units

Note: It is not poss ible to c onnec t a high outdoor temperature spec ific ation unit and the UWAP75 — 750.

D -NE T

I-Manager

D -NE T

D -NE T wiring adaptor

Water c ooled c hiller (1 port)Air-c ooling 240HP 2 units

Water-c ooling 400US R T 1 unit

Unified ON/OFF controller

Chilling unit

Possible to link withhost computer

Schedule timer

SkyAir series

VRV system

Central remote controllerPossible to have a forcedshut-down input

Enables control of other air conditioning systemssuch as VRV, SkyAir or HRV.

Enables individual control from chillers to air conditioners by using a single line.

Enables group control by remote controllers of both chillers and air conditioners.

Lets you develop a system that doesn't use individual remote controllers.(Central remote controller required)

Air handling unit Air handling unit Fan coil unit Possiblewireless remote controller

System configuration

D adaptor I-Manager option

Control Function List of I-Manager

I-Manager Control heat resources system by using I-Manager

New VersionNew Version

5 6

Model Lineup

50Hz60Hz50Hz60Hz50Hz60Hz50Hz60Hz

R-407C

R-22

Standard Unit

Year - Round Cooling Only Unit

Brine Cooling Unit

Standard Unit

Refrigerant Units series Model No.

UWAP—BY1UWAP—BYBUWAP—BY1KUWAP—BYBKUWAP—BY1ZUWAP—BYBZUWA—AY1UWA—AYB

Capacity (kW)

9, 10101112

12, 1313

14, 1515

page315120120120120120120120120

370140—

140—

140—

140—

420160—

160—

160—

160—

480180—

180—

180—

180—

530200—

200—

200—

200—

580220—

220—

220—

220—

630240—

240—

240—

240—

740280—

280—

280—

280—

840320—

320—

320—

320—

960360—

360—

360—

360—

1060400—

400—

400—

400—

1160440—

440—

440—

440—

1260480—

480—

480—

480—

50/60Hz50Hz60Hz50Hz60Hz50Hz60Hz50Hz50Hz60Hz

Refrigerant

R-407C

R-22

Units series

Standard Unit

Year - Round Cooling Only Unit

Brine Cooling Unit

Inverter Cooling Unit

Standard Unit

Model No.

UWAP—AY3*UWAP—BY1UWAP—BYBUWAP—BY1KUWAP—BYBKUWAP—BY1ZUWAP—BYBZUWAXP—AY1UWA—AY1UWA—AYB

Capacity (kW)6.7/7.5

75—————————

11.2/12.5125——————

125——

17/19190——————

190——

22.4/25250——————

250——

33.5/37.5375——————

375——

45/50500——————

500——

56/63630——————

630——

67/75750——————

750——

106—404040404040—4040

132—505050505050—5050

160—606060606060—6060

212—80—80—80——80—

265—

100100100100100100—

100100

99, 10101112

12, 131314

14, 1515

page

Note: Capacity figures are provided for reference and assume a power supply frequency of 60 Hz.

E mploys the new refrigerant R -407C .

UWAP 75 — 750AY 3 UWAXP 125 — 750AY 1UWAP 40 — 480B Y 1(K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

New Refrigerant Efficient and Reliable Compressors

To improve their operational reliability, 5 -- 30HP models employ scroll compressors , while 40 -- 480HP models are equipped with semi-hermetic s ingle screw compressors .

R efrigerant inlet

R efrigerant outlet

S emi-hermetic s ingle screw compressor

The user can select to give priority to either precis ion or reduced power consumption.

C ontinues operation to levels as low as 10(12)% of total capacity to provide stable water temperature c ontrol even during low-load peri-ods .

This mode can be used to re-duce power cons umption if highly precise water temperature control is not necessary dur-ing low-load periods. It shuts down the compressor when the load drops below 40% .

High-P rec is ion Mode Low-P ower Mode

Note: Switching between the above modes is accomplished using a control on the outdoor unit.

Multiple Operating Modes

Refrigerant Inlet

Refrigerant Outlet

Water Outlet

WaterInlet

Heat Exchanger with Stainless Steel Plates

S tainles s s teel heat ex-changer plates prevent rust, thereby improving their dura-bility and the system's op-

ReliabilityApplies to All Models

The compact des ign of these units s ignificantly reduces the space required for installation.

The horizontal linkup des ign increases installation flexibility.

In the outdoor unit, component parts of a small size have been used wherever possible to reduced its size and correspondingly reduce how much space it re-quires. Furthermore, replacing the 2-way refrigerant inlets with 4-way inlets has reduced the amount of space the outdoor unit needs even further.

This design provides the installation does not protrude so far, making it possible to install water chillers along a wall or under a roof overhang.

Note: Water supply piping must be purchased separately.(UWAP375AY3 — 750AY3)

UWAP 40 — 480B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

Easy Installation

UWAP 125AY 3 — 750AY 3

High load compliance and highly efficient inverter control provide highly precise adjustment of the water temperature, making it possible to reduce the size of the peripheral equipment.

UWAXP 125 — 750AY 1

C ompressor duty cycling control together with emergency operation and power-interruption auto-restart functions pro-vide enhanced air conditioning system reliability.

UWA40 — 480AY 1UWA40 — 120AY B

A choice of three control system is available.UWA40 — 480AY 1

Outflow water temperature controlProvides precise control of the water temprerature.(UWAP40 — 160BY1, UWA40 — 160AY1)

Compressor count controlControls the number of compressors operating depending on the load.(UWAP40 — 480BY1, UWA40 — 480AY1)

In flow water temperature controlPerforms duty cycling control.(UWAP40 — 480BY1, UWA40 — 480AY1)

Reduced Energy Wastage

C ontinuous capacity control with a range from 10% to 100% helps to reduce energy wastage during low-load

UWAP 40 — 160B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

UWAP 40 — 160B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

UWA40 — 160AY 1 UWA40 — 120AY B

UWA40 — 480AY 1UWAP 40 — 120AY B

UWAP 40 — 480B Y 1 (Z)UWAP 40 — 120B Y B (Z)

UWAP 40 — 480B Y 1

C apacityWater Temperature C ontrol R ange

Models E mploying R -407C Models E mploying R -22

3 — 30

40 — 480

5 to 16

4 to 25 (Inver C ooling Unit)

4 to 25

-10 to 0 (B rine C ooling Unit)

—

—

4 to 16

Wide Water Temperature Control Range

T he wide water temperature c ontrol range provides compatibility with a variety of heat source requirements .

A variety of brine-res is tant specification models are available that provide stable cooling operation at brine outflow temperatures down to -10 .

Applies to All Models

Applies to All Models

UWAP 120B Y 1KUWAXP 750AY 1 UWAP 180B Y 1

Wide Operation Range

A variety of year-round cooling type models are available that provide stable operation at outdoor temperatures down

The wide outdoor air temperature range ensures a s table supply of chilled water year round.

Applies to All Models

C apacityOutdoor Air Temperature R ange where C ooling P oss ible

Models E mploying R -407C Models E mploying R -22

3 — 30

40 — 480

-15 to 43

-5 to 43

-15 to 43 ( Y ear-R ound C ooling Only Unit )

0 to 43 ( B rine C ooling Unit )

—

—

-5 to 43

High Precision

10

9

8

7

Upper Limit S ignal

Water Temp. ( )

E xample of Outlet Water Temperature C ontrol

If outlet water temperature rises above the upper limit s ignal, the load starts to increase in 10% increments

As the temperature falls below the upper limit s ignal, the load increase increments are reduced to 5% .

As the temperature falls below the set value, the load increase increments remain at 5% .

When changes in outlet water temperature become 1 or less , the thermostat is turned off.

Value S et

The outlet water temperature is precisely controlled to within 0.5 (with a s table load) through the use of electric expansion

UWAXP 125 — 750AY 1

UWAP 40 — 160B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

UWA40 — 160AY 1UWA40 — 120AY B

Inverter control with high load compliance achieves highly accurate outflow water temperature control to within 0.5

Note: In systems with one compressor installed and where the load factor is 30% or more, and in systems with two or more compressors installed and where the load factor is 30% or more, control to within 0.5 is possible.

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

Air Cooled Water Chillers

: UWAP S eries UWAXP S eries : UWA S eries

7 8

Model Lineup

50Hz60Hz50Hz60Hz50Hz60Hz50Hz60Hz

R-407C

R-22

Standard Unit

Year - Round Cooling Only Unit

Brine Cooling Unit

Standard Unit

Refrigerant Units series Model No.

UWAP—BY1UWAP—BYBUWAP—BY1KUWAP—BYBKUWAP—BY1ZUWAP—BYBZUWA—AY1UWA—AYB

Capacity (kW)

9, 10101112

12, 1313

14, 1515

page315120120120120120120120120

370140—

140—

140—

140—

420160—

160—

160—

160—

480180—

180—

180—

180—

530200—

200—

200—

200—

580220—

220—

220—

220—

630240—

240—

240—

240—

740280—

280—

280—

280—

840320—

320—

320—

320—

960360—

360—

360—

360—

1060400—

400—

400—

400—

1160440—

440—

440—

440—

1260480—

480—

480—

480—

50/60Hz50Hz60Hz50Hz60Hz50Hz60Hz50Hz50Hz60Hz

Refrigerant

R-407C

R-22

Units series

Standard Unit

Year - Round Cooling Only Unit

Brine Cooling Unit

Inverter Cooling Unit

Standard Unit

Model No.

UWAP—AY3*UWAP—BY1UWAP—BYBUWAP—BY1KUWAP—BYBKUWAP—BY1ZUWAP—BYBZUWAXP—AY1UWA—AY1UWA—AYB

Capacity (kW)6.7/7.5

75—————————

11.2/12.5125——————

125——

17/19190——————

190——

22.4/25250——————

250——

33.5/37.5375——————

375——

45/50500——————

500——

56/63630——————

630——

67/75750——————

750——

106—404040404040—4040

132—505050505050—5050

160—606060606060—6060

212—80—80—80——80—

265—

100100100100100100—

100100

99, 10101112

12, 131314

14, 1515

page

Note: Capacity figures are provided for reference and assume a power supply frequency of 60 Hz.

E mploys the new refrigerant R -407C .

UWAP 75 — 750AY 3 UWAXP 125 — 750AY 1UWAP 40 — 480B Y 1(K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

New Refrigerant Efficient and Reliable Compressors

To improve their operational reliability, 5 -- 30HP models employ scroll compressors , while 40 -- 480HP models are equipped with semi-hermetic s ingle screw compressors .

R efrigerant inlet

R efrigerant outlet

S emi-hermetic s ingle screw compressor

The user can select to give priority to either precis ion or reduced power consumption.

C ontinues operation to levels as low as 10(12)% of total capacity to provide stable water temperature c ontrol even during low-load peri-ods .

This mode can be used to re-duce power cons umption if highly precise water temperature control is not necessary dur-ing low-load periods. It shuts down the compressor when the load drops below 40% .

High-P rec is ion Mode Low-P ower Mode

Note: Switching between the above modes is accomplished using a control on the outdoor unit.

Multiple Operating Modes

Refrigerant Inlet

Refrigerant Outlet

Water Outlet

WaterInlet

Heat Exchanger with Stainless Steel Plates

S tainles s s teel heat ex-changer plates prevent rust, thereby improving their dura-bility and the system's op-

ReliabilityApplies to All Models

The compact des ign of these units s ignificantly reduces the space required for installation.

The horizontal linkup des ign increases installation flexibility.

In the outdoor unit, component parts of a small size have been used wherever possible to reduced its size and correspondingly reduce how much space it re-quires. Furthermore, replacing the 2-way refrigerant inlets with 4-way inlets has reduced the amount of space the outdoor unit needs even further.

This design provides the installation does not protrude so far, making it possible to install water chillers along a wall or under a roof overhang.

Note: Water supply piping must be purchased separately.(UWAP375AY3 — 750AY3)

UWAP 40 — 480B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

Easy Installation

UWAP 125AY 3 — 750AY 3

High load compliance and highly efficient inverter control provide highly precise adjustment of the water temperature, making it possible to reduce the size of the peripheral equipment.

UWAXP 125 — 750AY 1

C ompressor duty cycling control together with emergency operation and power-interruption auto-restart functions pro-vide enhanced air conditioning system reliability.

UWA40 — 480AY 1UWA40 — 120AY B

A choice of three control system is available.UWA40 — 480AY 1

Outflow water temperature controlProvides precise control of the water temprerature.(UWAP40 — 160BY1, UWA40 — 160AY1)

Compressor count controlControls the number of compressors operating depending on the load.(UWAP40 — 480BY1, UWA40 — 480AY1)

In flow water temperature controlPerforms duty cycling control.(UWAP40 — 480BY1, UWA40 — 480AY1)

Reduced Energy Wastage

C ontinuous capacity control with a range from 10% to 100% helps to reduce energy wastage during low-load

UWAP 40 — 160B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

UWAP 40 — 160B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

UWA40 — 160AY 1 UWA40 — 120AY B

UWA40 — 480AY 1UWAP 40 — 120AY B

UWAP 40 — 480B Y 1 (Z)UWAP 40 — 120B Y B (Z)

UWAP 40 — 480B Y 1

C apacityWater Temperature C ontrol R ange

Models E mploying R -407C Models E mploying R -22

3 — 30

40 — 480

5 to 16

4 to 25 (Inver C ooling Unit)

4 to 25

-10 to 0 (B rine C ooling Unit)

—

—

4 to 16

Wide Water Temperature Control Range

T he wide water temperature c ontrol range provides compatibility with a variety of heat source requirements .

A variety of brine-res is tant specification models are available that provide stable cooling operation at brine outflow temperatures down to -10 .

Applies to All Models

Applies to All Models

UWAP 120B Y 1KUWAXP 750AY 1 UWAP 180B Y 1

Wide Operation Range

A variety of year-round cooling type models are available that provide stable operation at outdoor temperatures down

The wide outdoor air temperature range ensures a s table supply of chilled water year round.

Applies to All Models

C apacityOutdoor Air Temperature R ange where C ooling P oss ible

Models E mploying R -407C Models E mploying R -22

3 — 30

40 — 480

-15 to 43

-5 to 43

-15 to 43 ( Y ear-R ound C ooling Only Unit )

0 to 43 ( B rine C ooling Unit )

—

—

-5 to 43

High Precision

10

9

8

7

Upper Limit S ignal

Water Temp. ( )

E xample of Outlet Water Temperature C ontrol

If outlet water temperature rises above the upper limit s ignal, the load starts to increase in 10% increments

As the temperature falls below the upper limit s ignal, the load increase increments are reduced to 5% .

As the temperature falls below the set value, the load increase increments remain at 5% .

When changes in outlet water temperature become 1 or less , the thermostat is turned off.

Value S et

The outlet water temperature is precisely controlled to within 0.5 (with a s table load) through the use of electric expansion

UWAXP 125 — 750AY 1

UWAP 40 — 160B Y 1 (K ) (Z) UWAP 40 — 120B Y B (K ) (Z)

UWA40 — 160AY 1UWA40 — 120AY B

Inverter control with high load compliance achieves highly accurate outflow water temperature control to within 0.5

Note: In systems with one compressor installed and where the load factor is 30% or more, and in systems with two or more compressors installed and where the load factor is 30% or more, control to within 0.5 is possible.

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

Air Cooled Water Chillers

: UWAP S eries UWAXP S eries : UWA S eries

7 8

10

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

118 — 355kW class

UWAP 40 — 120B Y BStandard Unit

60Hz

UWAP40BYB(40 )

UWAP50BYB(50 )

UWAP60BYB(60 )

UWAP100BYB(100 )

UWAP120BYB(120 )

118403,000 34 3 phase, 60 Hz 400/440 V, 4 wires system338 100~10-0Semi-hermetic sealed single-screw type 30 1Brazing Plate type Cross fin coil Propeller Direct drive 81028,5930.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,0001,6901,7230 to 43

150512,000 43

430

37 1

1,01035,6531.0 4

1,8101,846

180614,000 51

516

45 1

1,8701,910

3001,024,000 85

860

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5003,551

3551,212,000 101

1,018

45 2

3,6053,662

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

530 — 1,260kW class

UWAP 200 — 480B Y 1Standard Unit

50Hz

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWAP200BY1(200 )

UWAP220BY1(220 )

UWAP240BY1(240 )

UWAP280BY1(280 )

UWAP320BY1(320 )

UWAP360BY1(360 )

UWAP480BY1(460 )

5301,809,000 151 3 phase, 50 Hz 380/400/415 V, 4 wires system1,519 100~10-0 Semi-hermetic sealed single-screw type45 2+60Brazing Plate type Cross fin coil Propeller Direct drive3,010106,2531.0 14R-407C

5B Flange (125A HG20593-97)

2,456 7,050 2,0006,0006,1980 to 43

UWAP400BY1(400 )

UWAP440BY1(440 )

Model

Cooling capacity Power SupplyChilled Water Flow Rate Capacity Steps

Compressor

Evaporetor type Comdenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

Weight Operation weight Operation range

5801,979,000 165

1,663

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0006,5006,719

6302,150,000179

1,806

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,0057,245

7402,525,000 210

2,121

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97) (2,456 4,850 2,000) 24,125 24,196 2

8402,867,000 239

2,408

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 24,590 24,661 2

9603,276,000 273

2,752

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 25,500 25,691 2

1,0603,617,000 301

3,039

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 26,000 26,198 2

1,1603,959,000 330

3,325

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 26,500 26,719 2

1,2604,300,000 358

3,612

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 27,005 27,245 2

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWAP40BY1(40 )

UWAP50BY1(50 )

UWAP60BY1(60 )

UWAP80BY1(80 )

UWAP100BY1(100 )

UWAP120BY1(120 )

UWAP180BY1(180 )

106362,000 30 3 phase, 50 Hz 380/400/415 V, 4 wires system304100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000

1,6901,7230 to 43

UWAP140BY1(140 )

UWAP160BY1(160 )

106 — 480kW class

UWAP 40 — 180B Y 1Standard Unit

50Hz

Model

Cooling capacity Power SupplyChilled Water Flow Rate Capacity Steps

Compressor

Evaporetor type Comdenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

Weight Operation weight Operation range

132450,000 38

378

37 1

86030,3581.0 4

1,8101,846

160546,000 46

459

45 1

1,8701,910

210717,000 60

602

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,3752,422

265904,000 75

760

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,000

3,5003,551

3201,092,000 91

917

45 2

1,72060,716

3,6053,662

3701,263,000 105

1,061

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,1254,196

4201,433,000 119

1,204

60 2

2,58091,0741.0 12

2,456 5,300 2,0004,5904,661

4801,638,000 137

1,376

45 3

5B Flange (125A HG20593-97) 2,456 6,600 2,0005,5005,691

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB). *2 The following safety devices are equipped as standard. • High pressure switch. • Reverse-phase protector. • Fusible plug. • Freeze up thermostat. • Overcurrent relay for compressor

and fan motor. • Overheat protection for discharge gas. • fan thermal protector.*3 This product is manufactured in Japan.

S pecifications

kWBtu/hUSRT

/min

%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity(50/60 Hz)

Power supplyChilled water flow rate (50/60 Hz)Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDriveAir flow rate(50/60 Hz)Motor output

UWAP75AY3(3 )

UWAP125AY3(5 )

UWAP190AY3(8 )

UWAP250AY3(10 )

UWAP375AY3(15 )

UWAP750AY3(30 )

6.7/7.522,900/25,6001.91/2.133 phase, 50 Hz 380/400/415 V, 60 Hz 400/440 V, 3 wires system

19/22

100-0Hermetically sealed scroll type2.2 1Brazed plate heat exchangerCross fin coilPropellerDirect drive75/852,650/3,0000.14 1R-407C

1B Flange (JIS10K)(25A) 2

1,450 635 (839) 690136138-15 to 43

11.2/12.538,200/42,7003.19/3.55

32/36

3.75 1

90/953,180/3,3500.20 1

140142

17.0/19.058,000/64,9004.83/5.40

49/54

5.5 1

140/1604,940/5,6500.215+0.14

1 1/2B Flange (JIS10K)(40A) 2

1,450 1,280 690248253

22.4/25.076,500/85,4006.37/7.11

64/72

7.5 1

175/1856,180/6,5300.215+0.22

260264

33.5/37.5114,000/128,0009.53/10.7

96/108

100-67-34-0

7.5+3.75

265/2809,350/9,880(0.215+0.22)+0.2

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 21,500 1,925 690400407

45.0/50.0154,000/171,00012.8/14.2

129/143

100-50-0

7.5 2

350/37012,400/13,100(0.215+0.22) 2

1 1/2B Flange(JIS10K)(40A) 4

1,500 2,570 690515525

56.0/63.0191,000/215,00015.9/17.9

161/181

100-80-60-40-20-0

7.5 2+3.75

440/46515,500/16,400(0.215+0.22) 2+0.2

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 41,550 3,230 758680695

67.0/75.0229,000/256,00019.1/21.3

192/215

100-67-34-0

7.5 3

525/55518,500/19,600(0.215+0.22) 3

1 1/2B Flange(JIS10K)(40A) 6

1,550 3,870 758800820

UWAP500AY3(20 )

UWAP630AY3(25 )

*1

6.7/7.5 — 67/75kW class

UWAP 75 — 750AY 3Standard Unit

50/60Hz

9

Air Cooled Water Chillers

10

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

118 — 355kW class

UWAP 40 — 120B Y BStandard Unit

60Hz

UWAP40BYB(40 )

UWAP50BYB(50 )

UWAP60BYB(60 )

UWAP100BYB(100 )

UWAP120BYB(120 )

118403,000 34 3 phase, 60 Hz 400/440 V, 4 wires system338 100~10-0Semi-hermetic sealed single-screw type 30 1Brazing Plate type Cross fin coil Propeller Direct drive 81028,5930.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,0001,6901,7230 to 43

150512,000 43

430

37 1

1,01035,6531.0 4

1,8101,846

180614,000 51

516

45 1

1,8701,910

3001,024,000 85

860

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5003,551

3551,212,000 101

1,018

45 2

3,6053,662

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

530 — 1,260kW class

UWAP 200 — 480B Y 1Standard Unit

50Hz

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWAP200BY1(200 )

UWAP220BY1(220 )

UWAP240BY1(240 )

UWAP280BY1(280 )

UWAP320BY1(320 )

UWAP360BY1(360 )

UWAP480BY1(460 )

5301,809,000 151 3 phase, 50 Hz 380/400/415 V, 4 wires system1,519 100~10-0 Semi-hermetic sealed single-screw type45 2+60Brazing Plate type Cross fin coil Propeller Direct drive3,010106,2531.0 14R-407C

5B Flange (125A HG20593-97)

2,456 7,050 2,0006,0006,1980 to 43

UWAP400BY1(400 )

UWAP440BY1(440 )

Model

Cooling capacity Power SupplyChilled Water Flow Rate Capacity Steps

Compressor

Evaporetor type Comdenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

Weight Operation weight Operation range

5801,979,000 165

1,663

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0006,5006,719

6302,150,000179

1,806

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,0057,245

7402,525,000 210

2,121

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97) (2,456 4,850 2,000) 24,125 24,196 2

8402,867,000 239

2,408

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 24,590 24,661 2

9603,276,000 273

2,752

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 25,500 25,691 2

1,0603,617,000 301

3,039

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 26,000 26,198 2

1,1603,959,000 330

3,325

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 26,500 26,719 2

1,2604,300,000 358

3,612

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 27,005 27,245 2

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWAP40BY1(40 )

UWAP50BY1(50 )

UWAP60BY1(60 )

UWAP80BY1(80 )

UWAP100BY1(100 )

UWAP120BY1(120 )

UWAP180BY1(180 )

106362,000 30 3 phase, 50 Hz 380/400/415 V, 4 wires system304100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000

1,6901,7230 to 43

UWAP140BY1(140 )

UWAP160BY1(160 )

106 — 480kW class

UWAP 40 — 180B Y 1Standard Unit

50Hz

Model

Cooling capacity Power SupplyChilled Water Flow Rate Capacity Steps

Compressor

Evaporetor type Comdenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

Weight Operation weight Operation range

132450,000 38

378

37 1

86030,3581.0 4

1,8101,846

160546,000 46

459

45 1

1,8701,910

210717,000 60

602

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,3752,422

265904,000 75

760

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,000

3,5003,551

3201,092,000 91

917

45 2

1,72060,716

3,6053,662

3701,263,000 105

1,061

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,1254,196

4201,433,000 119

1,204

60 2

2,58091,0741.0 12

2,456 5,300 2,0004,5904,661

4801,638,000 137

1,376

45 3

5B Flange (125A HG20593-97) 2,456 6,600 2,0005,5005,691

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB). *2 The following safety devices are equipped as standard. • High pressure switch. • Reverse-phase protector. • Fusible plug. • Freeze up thermostat. • Overcurrent relay for compressor

and fan motor. • Overheat protection for discharge gas. • fan thermal protector.*3 This product is manufactured in Japan.

S pecifications

kWBtu/hUSRT

/min

%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity(50/60 Hz)

Power supplyChilled water flow rate (50/60 Hz)Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDriveAir flow rate(50/60 Hz)Motor output

UWAP75AY3(3 )

UWAP125AY3(5 )

UWAP190AY3(8 )

UWAP250AY3(10 )

UWAP375AY3(15 )

UWAP750AY3(30 )

6.7/7.522,900/25,6001.91/2.133 phase, 50 Hz 380/400/415 V, 60 Hz 400/440 V, 3 wires system

19/22

100-0Hermetically sealed scroll type2.2 1Brazed plate heat exchangerCross fin coilPropellerDirect drive75/852,650/3,0000.14 1R-407C

1B Flange (JIS10K)(25A) 2

1,450 635 (839) 690136138-15 to 43

11.2/12.538,200/42,7003.19/3.55

32/36

3.75 1

90/953,180/3,3500.20 1

140142

17.0/19.058,000/64,9004.83/5.40

49/54

5.5 1

140/1604,940/5,6500.215+0.14

1 1/2B Flange (JIS10K)(40A) 2

1,450 1,280 690248253

22.4/25.076,500/85,4006.37/7.11

64/72

7.5 1

175/1856,180/6,5300.215+0.22

260264

33.5/37.5114,000/128,0009.53/10.7

96/108

100-67-34-0

7.5+3.75

265/2809,350/9,880(0.215+0.22)+0.2

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 21,500 1,925 690400407

45.0/50.0154,000/171,00012.8/14.2

129/143

100-50-0

7.5 2

350/37012,400/13,100(0.215+0.22) 2

1 1/2B Flange(JIS10K)(40A) 4

1,500 2,570 690515525

56.0/63.0191,000/215,00015.9/17.9

161/181

100-80-60-40-20-0

7.5 2+3.75

440/46515,500/16,400(0.215+0.22) 2+0.2

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 41,550 3,230 758680695

67.0/75.0229,000/256,00019.1/21.3

192/215

100-67-34-0

7.5 3

525/55518,500/19,600(0.215+0.22) 3

1 1/2B Flange(JIS10K)(40A) 6

1,550 3,870 758800820

UWAP500AY3(20 )

UWAP630AY3(25 )

*1

6.7/7.5 — 67/75kW class

UWAP 75 — 750AY 3Standard Unit

50/60Hz

9

Air Cooled Water Chillers

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

*1

118 — 355kW class

UWAP 40 — 120B Y B KYear - Round Cooling Only Unit

60Hz

UWAP40BYBK(40 )

UWAP50BYBK(50 )

UWAP60BYBK(60 )

UWAP100BYBK(100 )

UWAP120BYBK(120 )

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

*1

530 — 1,260kW class

UWAP 200 — 480B Y 1KYear - Round Cooling Only Unit

50Hz

UWAP200BY1K(200 )

UWAP220BY1K(220 )

UWAP240BY1K(240 )

UWAP280BY1K(280 )

UWAP320BY1K(320 )

UWAP360BY1K(360 )

UWAP400BY1K(400 )

UWAP440BY1K(440 )

UWAP480BY1K(480 )

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

*1

106 — 480kW class

UWAP 40 — 180B Y 1KYear - Round Cooling Only Unit

50Hz

UWAP40BY1K(40 )

UWAP50BY1K(50 )

UWAP60BY1K(60 )

UWAP80BY1K(80 )

UWAP100BY1K(100 )

UWAP120BY1K(120 )

UWAP140BY1K(140 )

UWAP160BY1K(160 )

UWAP180BY1K(180 )

Air Cooled Water Chillers

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

68 — 303kW class

UWAP 40 — 180B Y 1ZBrine Cooling Unit

50Hz

UWAP40BY1Z(40 )

UWAP50BY1Z(50 )

UWAP60BY1Z(60 )

UWAP80BY1Z(80 )

UWAP100BY1Z(100 )

UWAP120BY1Z(120 )

UWAP140BY1Z(140 )

UWAP160BY1Z(160 )

UWAP180BY1Z(180 )

68232,000 193 phase, 50 Hz 380/400/415 V, 4 wires system 428 100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000

1,6901,723ambient temp. 0 to 43, Brine temp. -10 to 16

83283,000 24

522

37 1

86030,3581.0 4

1,8101,846

101345,000 29

635

45 1

1,8701,910

135460,000 38

848

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,3752,422

166567,000 47

1,044

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,000

3,5003,551

205700,000 58

1,290

45 2

1,72060,716

3,6053,662

236804,00067

1,483

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,1254,196

269918,00077

1,693

60 2

2,58091,0741.0 12

2,456 5,300 2,0004,5904,661

3031,034,000 86

1,906

45 3

5B Flange (125A HG20593-97)2,456 6,600 2,0005,5005,691

118403,000 343 phase, 60 Hz 400/440 V, 4 wires system 338100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive81028,5930.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000 1,7151,748-15 to 43

150512,00043

430

37 1

1,01035,6531.0 4

1,8351,871

180614,00051

516

45 1

1,8951,935

3001,024,00085

860

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5503,601

3551,212,000101

1,018

45 2

3,6553,712

106362,000 303 phase, 50 Hz 380/400/415 V, 4 wires system 304 100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000

1,7151,748-15 to 43

5301,809,000 1513 phase, 50 Hz 380/400/415 V, 4 wires system 1,519100~10-0 Semi-hermetic sealed single-screw type40 2+60Brazing Plate type Cross fin coil Propeller Direct drive3,010106,2531.0 14R-407C

5B Flange (125A HG20593-97)

2,456 7,050 2,000 6,0856,283-15 to 43

5801,979,000165

1,663

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0006,5956,814

6302,150,000179

1,806

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,1107,350

7402,525,000210

2,121

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97)

(2,450 4,850 2,000) 24,185 24,256 2

8402,867,000239

2,408

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 24,660 24,731 2

9603,276,000273

2,752

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 25,575 25,766 2

1,0603,617,000301

3,039

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 26,085 26,283 2

1,1603,959,000330

3,325

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 26,595 26,814 2

1,2604,300,000358

3,612

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 27,110 27,350 2

132450,00038

378

37 1

86030,3581.0 4

1.8351.871

160546,00046

459

45 1

1,8951,935

210717,00060

602

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,4102,457

265904,00075

760

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,000

3,5503,601

3201,092,00091

917

45 2

1,72060,716

3,6553,712

3701,263,000105

1,061

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,1854,256

4201,433,000119

1,204

60 2

2,58091,0741.0 12

2,456 5,300 2,0004,6604,731

4801,638,000137

1,376

45 3

5B Flange (125A HG20593-97)2,456 6,600 2,0005,5755,766

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

11 12

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

*1

118 — 355kW class

UWAP 40 — 120B Y B KYear - Round Cooling Only Unit

60Hz

UWAP40BYBK(40 )

UWAP50BYBK(50 )

UWAP60BYBK(60 )

UWAP100BYBK(100 )

UWAP120BYBK(120 )

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

*1

530 — 1,260kW class

UWAP 200 — 480B Y 1KYear - Round Cooling Only Unit

50Hz

UWAP200BY1K(200 )

UWAP220BY1K(220 )

UWAP240BY1K(240 )

UWAP280BY1K(280 )

UWAP320BY1K(320 )

UWAP360BY1K(360 )

UWAP400BY1K(400 )

UWAP440BY1K(440 )

UWAP480BY1K(480 )

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

*1

106 — 480kW class

UWAP 40 — 180B Y 1KYear - Round Cooling Only Unit

50Hz

UWAP40BY1K(40 )

UWAP50BY1K(50 )

UWAP60BY1K(60 )

UWAP80BY1K(80 )

UWAP100BY1K(100 )

UWAP120BY1K(120 )

UWAP140BY1K(140 )

UWAP160BY1K(160 )

UWAP180BY1K(180 )

Air Cooled Water Chillers

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

68 — 303kW class

UWAP 40 — 180B Y 1ZBrine Cooling Unit

50Hz

UWAP40BY1Z(40 )

UWAP50BY1Z(50 )

UWAP60BY1Z(60 )

UWAP80BY1Z(80 )

UWAP100BY1Z(100 )

UWAP120BY1Z(120 )

UWAP140BY1Z(140 )

UWAP160BY1Z(160 )

UWAP180BY1Z(180 )

68232,000 193 phase, 50 Hz 380/400/415 V, 4 wires system 428 100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000

1,6901,723ambient temp. 0 to 43, Brine temp. -10 to 16

83283,000 24

522

37 1

86030,3581.0 4

1,8101,846

101345,000 29

635

45 1

1,8701,910

135460,000 38

848

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,3752,422

166567,000 47

1,044

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,000

3,5003,551

205700,000 58

1,290

45 2

1,72060,716

3,6053,662

236804,00067

1,483

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,1254,196

269918,00077

1,693

60 2

2,58091,0741.0 12

2,456 5,300 2,0004,5904,661

3031,034,000 86

1,906

45 3

5B Flange (125A HG20593-97)2,456 6,600 2,0005,5005,691

118403,000 343 phase, 60 Hz 400/440 V, 4 wires system 338100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive81028,5930.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000 1,7151,748-15 to 43

150512,00043

430

37 1

1,01035,6531.0 4

1,8351,871

180614,00051

516

45 1

1,8951,935

3001,024,00085

860

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5503,601

3551,212,000101

1,018

45 2

3,6553,712

106362,000 303 phase, 50 Hz 380/400/415 V, 4 wires system 304 100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,000

1,7151,748-15 to 43

5301,809,000 1513 phase, 50 Hz 380/400/415 V, 4 wires system 1,519100~10-0 Semi-hermetic sealed single-screw type40 2+60Brazing Plate type Cross fin coil Propeller Direct drive3,010106,2531.0 14R-407C

5B Flange (125A HG20593-97)

2,456 7,050 2,000 6,0856,283-15 to 43

5801,979,000165

1,663

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0006,5956,814

6302,150,000179

1,806

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,1107,350

7402,525,000210

2,121

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97)

(2,450 4,850 2,000) 24,185 24,256 2

8402,867,000239

2,408

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 24,660 24,731 2

9603,276,000273

2,752

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 25,575 25,766 2

1,0603,617,000301

3,039

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 26,085 26,283 2

1,1603,959,000330

3,325

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 26,595 26,814 2

1,2604,300,000358

3,612

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 27,110 27,350 2

132450,00038

378

37 1

86030,3581.0 4

1.8351.871

160546,00046

459

45 1

1,8951,935

210717,00060

602

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,4102,457

265904,00075

760

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,000

3,5503,601

3201,092,00091

917

45 2

1,72060,716

3,6553,712

3701,263,000105

1,061

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,1854,256

4201,433,000119

1,204

60 2

2,58091,0741.0 12

2,456 5,300 2,0004,6604,731

4801,638,000137

1,376

45 3

5B Flange (125A HG20593-97)2,456 6,600 2,0005,5755,766

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

11 12

S pecifications

kWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

12.542,7003.553 phase, 50 Hz 380/400/415 V, 4 wires system36100~35Hermetically sealed scroll type3.5 1Blazing plate heat exchangersCross fin coilPropellerDirect drive (Inverter system)803,1800.20 1R-407C1B Flange (JIS10K)(25A)1,450 835 690 150152-15 to 43

19.064,9005.40

54100~20

(3.5+2.2) 1

1504,940(0.20+0.14) 1

1 1/2B Flange (JIS10K)(25A)

1,450 1,280 690250252

25.085,4007.11

72

(3.5+3.75) 1

1706,180(0.20+0.18) 1

260263

50.0171,00014.2

143

(5.5+7.5) 1

34012,400(0.14+0.20) 2

1,500 2,570 690510517

63.0215,00017.9

181

(3.5+3.75)+(5.5+5.5)

170+2656,180+9,350(0.20+0.18)+0.20 3

2 1/2B Flange (JIS10K)(65A)

1,550 3,230 758715730

75.0256,00021.3

215

(3.5+3.75)+(5.5+7.5)

170+3406,180+12,400(0.20+0.18)+(0.14 2+0.20 2)

1,550 3,870 758790820

UWAXP750AY1(30 )

UWAXP630AY1(25 )

UWAXP500AY1(20 )

UWAXP375AY1(15 )

UWAXP250AY1(10 )

UWAXP190AY1(8 )

UWAXP125AY1(5 )

37.5128,00010.7

108

(5.5+5.5) 1

2659,3500.20 3

2B Flange (JIS10K)(50A)

1,500 1,925 690440446

*1

Pipe connections water inlet/outlet

Notes:*1 Cooling capacity is based on the following conditions : Entering water temp.12 (53.6 F), Ieaving chilled water temp.7 (44.5 F), and outdoor temp. 35 DB (95 FDB). *2 The following safety devices are equipped as standard. • High/ pressure switch. • Reverse-phase protector. • Fusible plug. • Freeze-up thermostat. • Overcurrent relay for compressor and fan motor. • Overheat protection for discharge gas. • Fan thermal protector. *3 This product is manufactured in Japan.

12.5 — 75kW class

UWAXP 125 — 750AY 1Inverter Cooling Unit

50Hz

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Brine Cooling Unit

337 — 808kW class

UWAP 200 — 480B Y 1Z50Hz

UWAP480BY1Z(480 )

UWAP440BY1Z(440 )

UWAP400BY1Z(400 )

UWAP360BY1Z(360 )

UWAP320BY1Z(320 )

UWAP280BY1Z(280 )

UWAP240BY1Z(240 )

UWAP220BY1Z(220 )

UWAP200BY1Z(200 )

3371,149,000 96 3 phase,50 Hz 380/400/415 V, 4 wires system 2,119100~10-0Semi-hermetic sealed single-screw type 45 2+60Brazing Plate type Cross fin coil Propeller Direct drive 3,010106,2531.0 14R-407C

5B Flange (125A HG20593-97)

2,456 7,050 2,0006,0006,198 ambient temp. 0 to 43, Brine temp. -10 to 16

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

3701,263,000 105

2,328

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0006,5006,719

4041,379,000 115

2,542

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,0057,245

4721,611,000 134

2,970

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97)

(2,456 4,850 2,000) 24,125 24,196 2

5381,836,000 153

3,385

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 2 4,590 24,661 2

6062,068,000 172

3,813

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 2 5,500 25,691 2

6742,300,000 192

4,241

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 2 6,000 26,198 2

7402,525,000 210

4,656

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 2 6,500 26,719 2

8082,757,000 230

5,084

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 2 7,005 27,245 2

Brine Cooling Unit

79 — 242kW class

UWAP 40 — 120B Y B Z60Hz

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

UWAP40BYBZ(40 )

UWAP50BYBZ(50 )

UWAP60BYBZ(60 )

UWAP100BYBZ(100 )

UWAP120BYBZ(120 )

242826,000 69

1,523

45 2

3,6053,662

79270,000 22 3 phase,60 Hz 400/440 V, 3 wires system 497 100~10-0Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive81028,5930.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,0001,6901,723ambient temp. 0 to 43, Brine temp. -10 to 16

94321,000 27

591

37 1

1,01035,6531.0 4

1,8101,846

121413,000 34

761

45 1

1,8701,910

188642,000 53

1,183

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5003,551

S pecifications

kWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWA40AY1(40 )

UWA50AY1(50 )

UWA60AY1(60 )

UWA80AYAY1(80 )

UWA100AY1(100 )

UWA120AY1(120 )

UWA180AY1(180 )

106362,000303 phase, 50 Hz 380/400/415 V, 4 wires system304100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type30 1Blazing Plate typeCross fin coilPropellerDirect drive70024,7100.5 4R-22

3B Flange (80A HG20593-97)

2,395 2,200 2,000 1,5001,517-5 to 43

132450,00038

378

37 1

71025,0630.8 4

1,6501,670

160546,00046

459

45 1

84029,6521.2 4

1,7501,773

265904,00075

760

37 2

1,42050,1260.8 8

4B Flange (100A HG20593-97)

2,395 4,400 2,0003,3003,336

3201,092,00091

917

45 2

1,68059,3041.2 8

3,5003,542

3701,263,000105

1,061

45+60

1,78062,834

3,6203,684

4201,433,000119

1,204

60 2

1,88066,364

3,6403,704

4801,638,000137

1,376

45 3

2,52088,9561.2 12

5B Flange (125A HG20593-97)2,460 6,600 2,0005,6055,670

UWA140AY1(140 )

UWA160AY1(160 )

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required.*4 Installation/operating weight includes the weight of refrigerant and refrigerant oil(charged before delivery).

210717,00060

602

60 1

94033,182

1,8201,852

*1

106 — 480kW class

UWA40 — 180AY 1Standard Unit

50Hz

Air Cooled Water Chillers

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

13 14

S pecifications

kWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

12.542,7003.553 phase, 50 Hz 380/400/415 V, 4 wires system36100~35Hermetically sealed scroll type3.5 1Blazing plate heat exchangersCross fin coilPropellerDirect drive (Inverter system)803,1800.20 1R-407C1B Flange (JIS10K)(25A)1,450 835 690 150152-15 to 43

19.064,9005.40

54100~20

(3.5+2.2) 1

1504,940(0.20+0.14) 1

1 1/2B Flange (JIS10K)(25A)

1,450 1,280 690250252

25.085,4007.11

72

(3.5+3.75) 1

1706,180(0.20+0.18) 1

260263

50.0171,00014.2

143

(5.5+7.5) 1

34012,400(0.14+0.20) 2

1,500 2,570 690510517

63.0215,00017.9

181

(3.5+3.75)+(5.5+5.5)

170+2656,180+9,350(0.20+0.18)+0.20 3

2 1/2B Flange (JIS10K)(65A)

1,550 3,230 758715730

75.0256,00021.3

215

(3.5+3.75)+(5.5+7.5)

170+3406,180+12,400(0.20+0.18)+(0.14 2+0.20 2)

1,550 3,870 758790820

UWAXP750AY1(30 )

UWAXP630AY1(25 )

UWAXP500AY1(20 )

UWAXP375AY1(15 )

UWAXP250AY1(10 )

UWAXP190AY1(8 )

UWAXP125AY1(5 )

37.5128,00010.7

108

(5.5+5.5) 1

2659,3500.20 3

2B Flange (JIS10K)(50A)

1,500 1,925 690440446

*1

Pipe connections water inlet/outlet

Notes:*1 Cooling capacity is based on the following conditions : Entering water temp.12 (53.6 F), Ieaving chilled water temp.7 (44.5 F), and outdoor temp. 35 DB (95 FDB). *2 The following safety devices are equipped as standard. • High/ pressure switch. • Reverse-phase protector. • Fusible plug. • Freeze-up thermostat. • Overcurrent relay for compressor and fan motor. • Overheat protection for discharge gas. • Fan thermal protector. *3 This product is manufactured in Japan.

12.5 — 75kW class

UWAXP 125 — 750AY 1Inverter Cooling Unit

50Hz

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Brine Cooling Unit

337 — 808kW class

UWAP 200 — 480B Y 1Z50Hz

UWAP480BY1Z(480 )

UWAP440BY1Z(440 )

UWAP400BY1Z(400 )

UWAP360BY1Z(360 )

UWAP320BY1Z(320 )

UWAP280BY1Z(280 )

UWAP240BY1Z(240 )

UWAP220BY1Z(220 )

UWAP200BY1Z(200 )

3371,149,000 96 3 phase,50 Hz 380/400/415 V, 4 wires system 2,119100~10-0Semi-hermetic sealed single-screw type 45 2+60Brazing Plate type Cross fin coil Propeller Direct drive 3,010106,2531.0 14R-407C

5B Flange (125A HG20593-97)

2,456 7,050 2,0006,0006,198 ambient temp. 0 to 43, Brine temp. -10 to 16

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

3701,263,000 105

2,328

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0006,5006,719

4041,379,000 115

2,542

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,0057,245

4721,611,000 134

2,970

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97)

(2,456 4,850 2,000) 24,125 24,196 2

5381,836,000 153

3,385

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 2 4,590 24,661 2

6062,068,000 172

3,813

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 2 5,500 25,691 2

6742,300,000 192

4,241

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 2 6,000 26,198 2

7402,525,000 210

4,656

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 2 6,500 26,719 2

8082,757,000 230

5,084

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 2 7,005 27,245 2

Brine Cooling Unit

79 — 242kW class

UWAP 40 — 120B Y B Z60Hz

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 This product is manufactured in China.

UWAP40BYBZ(40 )

UWAP50BYBZ(50 )

UWAP60BYBZ(60 )

UWAP100BYBZ(100 )

UWAP120BYBZ(120 )

242826,000 69

1,523

45 2

3,6053,662

79270,000 22 3 phase,60 Hz 400/440 V, 3 wires system 497 100~10-0Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive81028,5930.5 4R-407C

3B Flange (80A HG20593-97)

2,456 2,200 2,0001,6901,723ambient temp. 0 to 43, Brine temp. -10 to 16

94321,000 27

591

37 1

1,01035,6531.0 4

1,8101,846

121413,000 34

761

45 1

1,8701,910

188642,000 53

1,183

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5003,551

S pecifications

kWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWA40AY1(40 )

UWA50AY1(50 )

UWA60AY1(60 )

UWA80AYAY1(80 )

UWA100AY1(100 )

UWA120AY1(120 )

UWA180AY1(180 )

106362,000303 phase, 50 Hz 380/400/415 V, 4 wires system304100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type30 1Blazing Plate typeCross fin coilPropellerDirect drive70024,7100.5 4R-22

3B Flange (80A HG20593-97)

2,395 2,200 2,000 1,5001,517-5 to 43

132450,00038

378

37 1

71025,0630.8 4

1,6501,670

160546,00046

459

45 1

84029,6521.2 4

1,7501,773

265904,00075

760

37 2

1,42050,1260.8 8

4B Flange (100A HG20593-97)

2,395 4,400 2,0003,3003,336

3201,092,00091

917

45 2

1,68059,3041.2 8

3,5003,542

3701,263,000105

1,061

45+60

1,78062,834

3,6203,684

4201,433,000119

1,204

60 2

1,88066,364

3,6403,704

4801,638,000137

1,376

45 3

2,52088,9561.2 12

5B Flange (125A HG20593-97)2,460 6,600 2,0005,6055,670

UWA140AY1(140 )

UWA160AY1(160 )

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required.*4 Installation/operating weight includes the weight of refrigerant and refrigerant oil(charged before delivery).

210717,00060

602

60 1

94033,182

1,8201,852

*1

106 — 480kW class

UWA40 — 180AY 1Standard Unit

50Hz

Air Cooled Water Chillers

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

13 14

UWAP40BY1UWAP40BYB

UWAP50BY1UWAP50BYB

UWAP60BY1UWAP60BYB UWAP80BY1 UWAP100BY1

UWAP100BYBUWAP120BY1

UWAP120BYB UWAP140BY1 UWAP160BY1 UWAP180BY1

Model

Remote controllerCommunication I/F P.C. boardCommunication I/F P.C. B storage boxTransmission wireCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307C50BRP66B3 1BRP66A97 1(external)BER66A5 1DCS302CA61DCS301BA61DST301BA61

BRP66A100 1(internal)BER66A7 1

Not required (S.Box installed)

UWAP75AY3 UWAP125AY3 UWAP190AY3 UWAP250AY3 UWAP375AY3 UWAP500AY3 UWAP630AY3 UWAP750AY3*1

*1*1*1

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP40BGWP-UWYP40BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWP-UWYP80BGWEL-UWYP100BGWP-UWYP100B

GWEL-UWYP180BGWP-UWYP180B

UWAP200BY1 UWAP220BY1 UWAP240BY1 UWAP280BY1 UWAP320BY1 UWAP360BY1 UWAP400BY1 UWAP440BY1 UWAP480BY1Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP180BGWP-UWYP180BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWEL-UWYP280BGWP-UWYP280B

GWEL-UWYP360BGWP-UWYP360B

Notes:*1 Communication I/F P.C. board, Communication I/F P.C. B storage box and Transmission wire are also required.

Model

Remote controller *1Communication I/F P.C. boardCommunication I/F P.C. B storage boxTransmission wire

UWAXP125AY1

UWA40AY1UWA40AYB

UWA50AY1UWA50AYB

UWA60AY1UWA60AYB UWA80AY1 UWA100AY1

UWA100AYBUWA120AY1UWA120AYB UWA140AY1 UWA160AY1 UWA180AY1

UWAXP190AY1 UWAXP250AY1 UWAXP375AY1 UWAXP500AY1 UWAXP630AY1 UWAXP750AY1BRC307C50BRP66B3 1— BER66A5

BPR66A97BER66A6

—BER66A7

BRP66B3 2BRP66A96BER66A8

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

UWA200AY1 UWA220AY1 UWA240AY1 UWA280AY1 UWA320AY1 UWA360AY1 UWA400AY1 UWA440AY1 UWA480AY1

BRC307D503GWEL-UWY40AGWP-UWY40ADAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

BRC307D503GWEL-UWY180AGWP-UWY180ADAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWEL-UWY80A GWP-UWY80A GWP-UWY100A

GWEL-UWY180AGWP-UWY180A

GWEL-UWY280AGWEL-UWY281A

GWEL-UWY360AGWP-UWY360A

Notes: *1 Communication I/F P.C. board, Communication I/F P.C. B storage box and Transmission waire are also required.

Option L is t

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 The limited length of wire represents its max. length when the pressure is lower than 2%.*5 This product is manufactured in China.

*1

118 — 355kW class

UWA40 — 120AY BStandard Unit

60Hz

UWA120AYB(120 )

UWA100AYB(100 )

UWA60AYB(60 )

UWA50AYB(50 )

UWA40AYB(40 )

118403,000343 phase, 60 Hz 400/440 V, 4 wires system 338100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type30 1Blazing Plate typeCross fin coilPropellerDirect drive80028,2400.5 4R-22

3B Flange (80A)

2,395 2,200 2,0001,5001,517-5 to 43

150512,00043

430

37 1

81028,5930.8 4

1,6501,670

180614,00051

516

45 1

94033,1821.2 4

1,7501,773

3001,024,00085

860

37 2

1,62057,1860.8 8

4B Flange (100A)

2,395 4,400 2,0003,3003,336

3551,212,000101

1,018

45 2

1,88066,3641.2 8

3,5003,542

S pecifications

kWBtu/hUSRT

/min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWA200AY1(200 )

UWA220AY1(220 )

UWA240AY1(240 )

UWA280AY1(280 )

UWA320AY1(320 )

UWA360AY1(360 )

UWA480AY1(480 )

5301,809,0001513 phase, 50 Hz 380/400/415 V, 4 wires system1,519100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type45 2+60Blazing Plate typeCross fin coilPropellerDirect drive2,62092,4861.2 12R-22

5B Flange (125A HG20593-97)

2,460 6,600 2,000

5,6605,737-5 to 43

5801,979,000165

1,663

45+60 2

2,72096,016

5,6955,782

6302,150,000179

1,806

60 3

2,82099,546

5,7505,850

8402,867,000239

2,408

(60 2) 2

3.760132,728

3,640 23,704 2

9603,276,000273

2,752

(45 3) 2

5,040177,912(1.2 12) 2

5B Flange (125A HG20593-97)

(2,460 6,600 2,000) 2

5,605 25,670 2

1,0603,617,000301

3,039

(45 2+60) 2

5,240184,972

5,660 25,737 2

1,1603,959,000330

3,325

(45+60 2) 2

5,440192,032

5,695 25,782 2

1,2604,300,000358

3,612

(60 3) 2

5,640199,092

5,750 25,850 2

UWA400AY1(400 )

UWA440AY1(440 )

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required.*4 Installation/operating weight includes the weight of refrigerant and refrigerant oil(charged before delivery).

7402,525,000210

2,121

(45+60) 2

3,560125,668(1.2 8) 2

4B Flange (100A HG20593-97)

(2,395 4,400 2,000) 2

3,620 23,684 2

*1

530 — 1,260kW class

UWA200 — 480AY 1Standard Unit

50Hz

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

15 16

Air Cooled Water Chillers

UWAP40BY1UWAP40BYB

UWAP50BY1UWAP50BYB

UWAP60BY1UWAP60BYB UWAP80BY1 UWAP100BY1

UWAP100BYBUWAP120BY1

UWAP120BYB UWAP140BY1 UWAP160BY1 UWAP180BY1

Model

Remote controllerCommunication I/F P.C. boardCommunication I/F P.C. B storage boxTransmission wireCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307C50BRP66B3 1BRP66A97 1(external)BER66A5 1DCS302CA61DCS301BA61DST301BA61

BRP66A100 1(internal)BER66A7 1

Not required (S.Box installed)

UWAP75AY3 UWAP125AY3 UWAP190AY3 UWAP250AY3 UWAP375AY3 UWAP500AY3 UWAP630AY3 UWAP750AY3*1

*1*1*1

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP40BGWP-UWYP40BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWP-UWYP80BGWEL-UWYP100BGWP-UWYP100B

GWEL-UWYP180BGWP-UWYP180B

UWAP200BY1 UWAP220BY1 UWAP240BY1 UWAP280BY1 UWAP320BY1 UWAP360BY1 UWAP400BY1 UWAP440BY1 UWAP480BY1Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP180BGWP-UWYP180BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWEL-UWYP280BGWP-UWYP280B

GWEL-UWYP360BGWP-UWYP360B

Notes:*1 Communication I/F P.C. board, Communication I/F P.C. B storage box and Transmission wire are also required.

Model

Remote controller *1Communication I/F P.C. boardCommunication I/F P.C. B storage boxTransmission wire

UWAXP125AY1

UWA40AY1UWA40AYB

UWA50AY1UWA50AYB

UWA60AY1UWA60AYB UWA80AY1 UWA100AY1

UWA100AYBUWA120AY1UWA120AYB UWA140AY1 UWA160AY1 UWA180AY1

UWAXP190AY1 UWAXP250AY1 UWAXP375AY1 UWAXP500AY1 UWAXP630AY1 UWAXP750AY1BRC307C50BRP66B3 1— BER66A5

BPR66A97BER66A6

—BER66A7

BRP66B3 2BRP66A96BER66A8

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

UWA200AY1 UWA220AY1 UWA240AY1 UWA280AY1 UWA320AY1 UWA360AY1 UWA400AY1 UWA440AY1 UWA480AY1

BRC307D503GWEL-UWY40AGWP-UWY40ADAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

BRC307D503GWEL-UWY180AGWP-UWY180ADAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWEL-UWY80A GWP-UWY80A GWP-UWY100A

GWEL-UWY180AGWP-UWY180A

GWEL-UWY280AGWEL-UWY281A

GWEL-UWY360AGWP-UWY360A

Notes: *1 Communication I/F P.C. board, Communication I/F P.C. B storage box and Transmission waire are also required.

Option L is t

S pecifications

kWBtu/hUSRT /min%

kW

m3/mincfmkW

mmkgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 The unit is equipped with standard water filter.*4 The limited length of wire represents its max. length when the pressure is lower than 2%.*5 This product is manufactured in China.

*1

118 — 355kW class

UWA40 — 120AY BStandard Unit

60Hz

UWA120AYB(120 )

UWA100AYB(100 )

UWA60AYB(60 )

UWA50AYB(50 )

UWA40AYB(40 )

118403,000343 phase, 60 Hz 400/440 V, 4 wires system 338100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type30 1Blazing Plate typeCross fin coilPropellerDirect drive80028,2400.5 4R-22

3B Flange (80A)

2,395 2,200 2,0001,5001,517-5 to 43

150512,00043

430

37 1

81028,5930.8 4

1,6501,670

180614,00051

516

45 1

94033,1821.2 4

1,7501,773

3001,024,00085

860

37 2

1,62057,1860.8 8

4B Flange (100A)

2,395 4,400 2,0003,3003,336

3551,212,000101

1,018

45 2

1,88066,3641.2 8

3,5003,542

S pecifications

kWBtu/hUSRT

/min%

kW

m3/mincfmkW

mm

kgkg

Model

Cooling capacity

Power supplyChilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWA200AY1(200 )

UWA220AY1(220 )

UWA240AY1(240 )

UWA280AY1(280 )

UWA320AY1(320 )

UWA360AY1(360 )

UWA480AY1(480 )

5301,809,0001513 phase, 50 Hz 380/400/415 V, 4 wires system1,519100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type45 2+60Blazing Plate typeCross fin coilPropellerDirect drive2,62092,4861.2 12R-22

5B Flange (125A HG20593-97)

2,460 6,600 2,000

5,6605,737-5 to 43

5801,979,000165

1,663

45+60 2

2,72096,016

5,6955,782

6302,150,000179

1,806

60 3

2,82099,546

5,7505,850

8402,867,000239

2,408

(60 2) 2

3.760132,728

3,640 23,704 2

9603,276,000273

2,752

(45 3) 2

5,040177,912(1.2 12) 2

5B Flange (125A HG20593-97)

(2,460 6,600 2,000) 2

5,605 25,670 2

1,0603,617,000301

3,039

(45 2+60) 2

5,240184,972

5,660 25,737 2

1,1603,959,000330

3,325

(45+60 2) 2

5,440192,032

5,695 25,782 2

1,2604,300,000358

3,612

(60 3) 2

5,640199,092

5,750 25,850 2

UWA400AY1(400 )

UWA440AY1(440 )

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*3 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required.*4 Installation/operating weight includes the weight of refrigerant and refrigerant oil(charged before delivery).

7402,525,000210

2,121

(45+60) 2

3,560125,668(1.2 8) 2

4B Flange (100A HG20593-97)

(2,395 4,400 2,000) 2

3,620 23,684 2

*1

530 — 1,260kW class

UWA200 — 480AY 1Standard Unit

50Hz

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

15 16

Air Cooled Water Chillers

For High Outdoor Temperature Us e

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rate

Cooling capacity

Chilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

kWBtu/hUSRT

kWBtu/hUSRT

%

kW

m3/mincfmkW

mm

kgkg

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWA27JATJ(25 )

79.0269,80022.43 phase, 60 Hz, 208/230 V, 3 wires system20671.0242,00020.1185100-50-0Semi-hermetically sealed reciprocating22Dry expansion shell and Hi-X tubeCross fin coil (Waffle louver fins and Hi-X tubes)PropellerDirect drive58020,4801.7ea. 2R-22FPT2 (50A)1,765 2,025 1,06575079015 to 49

UWA32JATJ(30 )

UWA43JATJ(40 )

UWA53JATJ(50 )

UWA62JATJ(60 )

UWA70JATJ(70 )

UWA80JATJ(80 )

UWA90JATJ(90 )

UWA108JATJ(100 )

UWA122JATJ(120 )

94.3320,60026.7

24582.0280,90023.4215100-66-33-0

48016,9501.0ea. 2

1,915 2,025 1,065900970

125.0426,60035.5

326111.0378,90031.5289

30

1,16040,9601.0ea. 4

FPT2 1/2 (65A)

1,890 2,005 2,000

1,3001,3705 to 49

162.0553,50046.1

423145.0494,00041.0377100-75-50-25-0

37

1.7ea. 4

1,5401,630

185.0632,10052.6

483171.0584,10048.6466

45

1,40049,4302.5ea. 4

FPT3 (80A)

1,6101,700

212.0722,20060.0

552191.0653,10054.2497100-83-66-50-33-0

26 2

1,92067,8001.0ea. 8

4B Flange (JIS16K)(100A)1,745 2,005 4,0002,5002,60015 to 49

253.0865,00072.0

661219.0746,40062.1570

30 2

1,915 2,005 4,000

2,6002,730

274.0936,40078.0

715248.0845,20070.4645100-88-75-63-50-25-0

2,8502,980

324.01,107,00092.2

845285.0972,20081.0742

37 2

2,32081,9201.7ea. 8

5B Flange (JIS16K)(125A)

2,8703,000

370.01,262,000105.0

964335.01,145,00095.3873

45 2

2,80098,8702.5ea. 8

3,0503,210

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 35 DB(95 FDB).*2 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 46 DB(115 FDB).*3 The following safety devices are equipped as standard. • High/low pressure switch. • Oil pressure control switch. • Compressor thermal protector. • Recycling guard timer.

• Crankcase heater. • 3-element overcurrent relay for compressors and fan motors. • Freeze-up protection thermostat. • Fusible plug. • Safety valve(for UWA53, 62, 90, 108, 122JATJ).

*4 This product is manufactured in Japan.

*1

*2

79 — 370kW class

UWA27 — 122J ATJFor High Outdoor Temperature Use

60Hz

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rate

Compressor

Evaporator type

Condenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)Weight Operation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

kWBtu/hUSRT

kW

m3/mincfmkW

mmkg

351.61,201,50099.93 phase, 50 Hz 380/400/415 V, 4 wires system100-83-67-50-33-17-0Semi-hermetic sealed reciprocating30 3

Dry expansion shell and Hi-X tubes

Cross fin coil (Waffle louver fins and Hi-X tubes)PropellerDirect drive2,58091,1000.9ea. 12R-225B Flange (JIS16K)(125A)2,095 2,005 5,7004,3605 to 49

404.41,380,800115.0

37 3

3,000105,900

4,470

474.71,620,600135.0

45 3

3,720131,4001.5ea. 12

4,660

562.81,921,500160.0

100-88-75-63-50-25-0

37 4

Dry expansion shell and corrugated tubes

4,000141,3000.9ea. 16

2,075 2,005 8,0006,110

667.92,280,400189.9

45 4

4,960175,2001.5ea. 16

6,340

791.02,700,800224.7

100-83-67-50-33-17-0

37 6Dry expansion shell and Hi-X tubes

6,000211,9000.9ea. 24

2,095 2,005 11,400 8,940

UWA270JY1(300 )UWA228JY1(240 )UWA192JY1(200 )UWA162JY1(180 )UWA138JY1(150 )UWA120JY1(130 )

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure switch. • Low pressure switch. • Oil pressure control switch. • Compressor thermal protector. • Recycling

guard timer. • Crankcase heater. • 3-element overcurrent relay (Compressor, Fan motors). • Freeze-up protection thermostat. • Fusible plug. • Safety valve (except for UWA120JY1).*3 This product is manufactured in Japan.

*1

351.6 — 791kW class

UWA120 — 270J Y 1For High Outdoor Temperature Use

50Hz

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rate

Cooling capacity

Chilled water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

108.4369,80030.83 phase, 50 Hz 380/400/415 V, 4 wires system28297.4332,50027.7279100-66-33-0Semi-hermetically sealed reciprocating30Dry expansion shell and Hi-X tubeCross fin coil (Waffle louver fins and Hi-X tubes)PropellerDirect drive86030,3700.9ea. 4R-22

FPT2 1/2 (65A)

1,720 2,005 2,0001,2301,3005 to 52

137.2468,20039.0

358124.8425,80035.4325100-75-50-25-0

37

1,00035,310

1,890 2,005 2,0001,4201,490

161.3550,40045.8

420149.9511,50042.6391

45

1,24043,7901.5ea. 4

FPT3 (80A)

1,5201,610

186.0634,90052.9

485167.4571,40047.6436100-83-66-50-33-0

1,72060,7300.9ea. 8

1,745 2,005 4,0002,5002,600

219.1747,60062.3

571197.1672,60056.0514

30 2

4B Flange (JIS16K)(100A)

2,6002,730

250.6855,10071.2

653225.5769,40064.1588100-88-75-63-50-25-0

2,00070,620

1,915 2,005 4,0002,8502,980

272.7930,50077.5

711250.8855,90071.3654

37 2

2,8703,000

319.21,089,20090.7

832290.5991,20082.6757

45 2

2,48087,5801.5ea. 8

5B Flange(JIS16K)(125A)

3,0503,210

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 35 DB(95 FDB).*2 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 46 DB(115 FDB).*3 The following safety devices are equipped as standard. • High/low pressure switch. • Oil pressure control switch. • Compressor thermal protector. • Recycling guard timer.

• Crankcase heater. • 3-element overcurrent relay for compressors and fan motors. • Freeze-up prorection thermostat. • Fusible plug. • Safety valve(for UWA47, 55, 93, 109JAY1).*4 This product is manufactured in Japan.

UWA37JAY1(40 )

UWA47JAY1(50 )

UWA55JAY1(60 )

UWA63JAY1(70 )

UWA75JAY1(80 )

UWA80JAY1(90 )

UWA93JAY1(100 )

*1

*2

kWBtu/hUSRT

kWBtu/hUSRT

%

kW

m3/mincfmkW

mmkgkg

UWA109JAY1(120 )

108.4 — 319.2kW class

UWA37 — 109J AY 1For High Outdoor Temperature Use

50Hz

UWA55J AY 1 UWA138J Y 1 UWA80J ATJ

P rovides a s table supply of chilled water even when the outdoor temperature is as high as 49 .

C apacity can be controlled in multiple steps of between 3 and 7 for efficient energy use.

Full Lineup Includes Models with Capacities Ranging from 79 — 791kW.

Equipped with a Compact and Powerful Semi-hermetically Sealed Reciprocating Compressor.

: UWA S eries

UWA37J AY 1 — 109J AY 1UWA120J Y 1 — 270J Y 1U W A27J AT J / 32J AT J , 70J AT J — 122J AT JUWA43J ATJ — 62J ATJ

5 to 525 to 49

15 to 495 to 49

Wide Operating RangeTemperature range by model.

Wide Capacity RangeUWA37J AY 1 — 109J AY 1UWA43J ATJ — 122J ATJUWA120J Y 1 — 270J Y 1

A selector switch makes it possible to operate only one refrig-erant circuit while the other is under repair.

Two Independent Refrigerant CircuitsUWA63J AY 1 — 10 9J AY 1UWA70J ATJ — 122 J ATJUWA120J Y 1 — 270 J Y 1

Air Cooled Water Chillers

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

1718

For High Outdoor Temperature Us e

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rate

Cooling capacity

Chilled water flow rate Capacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

kWBtu/hUSRT

kWBtu/hUSRT

%

kW

m3/mincfmkW

mm

kgkg

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWA27JATJ(25 )

79.0269,80022.43 phase, 60 Hz, 208/230 V, 3 wires system20671.0242,00020.1185100-50-0Semi-hermetically sealed reciprocating22Dry expansion shell and Hi-X tubeCross fin coil (Waffle louver fins and Hi-X tubes)PropellerDirect drive58020,4801.7ea. 2R-22FPT2 (50A)1,765 2,025 1,06575079015 to 49

UWA32JATJ(30 )

UWA43JATJ(40 )

UWA53JATJ(50 )

UWA62JATJ(60 )

UWA70JATJ(70 )

UWA80JATJ(80 )

UWA90JATJ(90 )

UWA108JATJ(100 )

UWA122JATJ(120 )

94.3320,60026.7

24582.0280,90023.4215100-66-33-0

48016,9501.0ea. 2

1,915 2,025 1,065900970

125.0426,60035.5

326111.0378,90031.5289

30

1,16040,9601.0ea. 4

FPT2 1/2 (65A)

1,890 2,005 2,000

1,3001,3705 to 49

162.0553,50046.1

423145.0494,00041.0377100-75-50-25-0

37

1.7ea. 4

1,5401,630

185.0632,10052.6

483171.0584,10048.6466

45

1,40049,4302.5ea. 4

FPT3 (80A)

1,6101,700

212.0722,20060.0

552191.0653,10054.2497100-83-66-50-33-0

26 2

1,92067,8001.0ea. 8

4B Flange (JIS16K)(100A)1,745 2,005 4,0002,5002,60015 to 49

253.0865,00072.0

661219.0746,40062.1570

30 2

1,915 2,005 4,000

2,6002,730

274.0936,40078.0

715248.0845,20070.4645100-88-75-63-50-25-0

2,8502,980

324.01,107,00092.2

845285.0972,20081.0742

37 2

2,32081,9201.7ea. 8

5B Flange (JIS16K)(125A)

2,8703,000

370.01,262,000105.0

964335.01,145,00095.3873

45 2

2,80098,8702.5ea. 8

3,0503,210

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 35 DB(95 FDB).*2 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 46 DB(115 FDB).*3 The following safety devices are equipped as standard. • High/low pressure switch. • Oil pressure control switch. • Compressor thermal protector. • Recycling guard timer.

• Crankcase heater. • 3-element overcurrent relay for compressors and fan motors. • Freeze-up protection thermostat. • Fusible plug. • Safety valve(for UWA53, 62, 90, 108, 122JATJ).

*4 This product is manufactured in Japan.

*1

*2

79 — 370kW class

UWA27 — 122J ATJFor High Outdoor Temperature Use

60Hz

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rate

Compressor

Evaporator type

Condenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)Weight Operation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

kWBtu/hUSRT

kW

m3/mincfmkW

mmkg

351.61,201,50099.93 phase, 50 Hz 380/400/415 V, 4 wires system100-83-67-50-33-17-0Semi-hermetic sealed reciprocating30 3

Dry expansion shell and Hi-X tubes

Cross fin coil (Waffle louver fins and Hi-X tubes)PropellerDirect drive2,58091,1000.9ea. 12R-225B Flange (JIS16K)(125A)2,095 2,005 5,7004,3605 to 49

404.41,380,800115.0

37 3

3,000105,900

4,470

474.71,620,600135.0

45 3

3,720131,4001.5ea. 12

4,660

562.81,921,500160.0

100-88-75-63-50-25-0

37 4

Dry expansion shell and corrugated tubes

4,000141,3000.9ea. 16

2,075 2,005 8,0006,110

667.92,280,400189.9

45 4

4,960175,2001.5ea. 16

6,340

791.02,700,800224.7

100-83-67-50-33-17-0

37 6Dry expansion shell and Hi-X tubes

6,000211,9000.9ea. 24

2,095 2,005 11,400 8,940

UWA270JY1(300 )UWA228JY1(240 )UWA192JY1(200 )UWA162JY1(180 )UWA138JY1(150 )UWA120JY1(130 )

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 35 DB(95 FDB).*2 The following safety devices are equipped as standard. • High pressure switch. • Low pressure switch. • Oil pressure control switch. • Compressor thermal protector. • Recycling

guard timer. • Crankcase heater. • 3-element overcurrent relay (Compressor, Fan motors). • Freeze-up protection thermostat. • Fusible plug. • Safety valve (except for UWA120JY1).*3 This product is manufactured in Japan.

*1

351.6 — 791kW class

UWA120 — 270J Y 1For High Outdoor Temperature Use

50Hz

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rate

Cooling capacity

Chilled water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outletDimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDrive

Air flow rate

Motor output

108.4369,80030.83 phase, 50 Hz 380/400/415 V, 4 wires system28297.4332,50027.7279100-66-33-0Semi-hermetically sealed reciprocating30Dry expansion shell and Hi-X tubeCross fin coil (Waffle louver fins and Hi-X tubes)PropellerDirect drive86030,3700.9ea. 4R-22

FPT2 1/2 (65A)

1,720 2,005 2,0001,2301,3005 to 52

137.2468,20039.0

358124.8425,80035.4325100-75-50-25-0

37

1,00035,310

1,890 2,005 2,0001,4201,490

161.3550,40045.8

420149.9511,50042.6391

45

1,24043,7901.5ea. 4

FPT3 (80A)

1,5201,610

186.0634,90052.9

485167.4571,40047.6436100-83-66-50-33-0

1,72060,7300.9ea. 8

1,745 2,005 4,0002,5002,600

219.1747,60062.3

571197.1672,60056.0514

30 2

4B Flange (JIS16K)(100A)

2,6002,730

250.6855,10071.2

653225.5769,40064.1588100-88-75-63-50-25-0

2,00070,620

1,915 2,005 4,0002,8502,980

272.7930,50077.5

711250.8855,90071.3654

37 2

2,8703,000

319.21,089,20090.7

832290.5991,20082.6757

45 2

2,48087,5801.5ea. 8

5B Flange(JIS16K)(125A)

3,0503,210

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 35 DB(95 FDB).*2 Cooling capacity is based on the following conditions : Leaving chilled water temp.6.7 (44 F), entering chilled water temp.12.2 (54 F), and outdoor air temp. 46 DB(115 FDB).*3 The following safety devices are equipped as standard. • High/low pressure switch. • Oil pressure control switch. • Compressor thermal protector. • Recycling guard timer.

• Crankcase heater. • 3-element overcurrent relay for compressors and fan motors. • Freeze-up prorection thermostat. • Fusible plug. • Safety valve(for UWA47, 55, 93, 109JAY1).*4 This product is manufactured in Japan.

UWA37JAY1(40 )

UWA47JAY1(50 )

UWA55JAY1(60 )

UWA63JAY1(70 )

UWA75JAY1(80 )

UWA80JAY1(90 )

UWA93JAY1(100 )

*1

*2

kWBtu/hUSRT

kWBtu/hUSRT

%

kW

m3/mincfmkW

mmkgkg

UWA109JAY1(120 )

108.4 — 319.2kW class

UWA37 — 109J AY 1For High Outdoor Temperature Use

50Hz

UWA55J AY 1 UWA138J Y 1 UWA80J ATJ

P rovides a s table supply of chilled water even when the outdoor temperature is as high as 49 .

C apacity can be controlled in multiple steps of between 3 and 7 for efficient energy use.

Full Lineup Includes Models with Capacities Ranging from 79 — 791kW.

Equipped with a Compact and Powerful Semi-hermetically Sealed Reciprocating Compressor.

: UWA S eries

UWA37J AY 1 — 109J AY 1UWA120J Y 1 — 270J Y 1U W A27J AT J / 32J AT J , 70J AT J — 122J AT JUWA43J ATJ — 62J ATJ

5 to 525 to 49

15 to 495 to 49

Wide Operating RangeTemperature range by model.

Wide Capacity RangeUWA37J AY 1 — 109J AY 1UWA43J ATJ — 122J ATJUWA120J Y 1 — 270J Y 1

A selector switch makes it possible to operate only one refrig-erant circuit while the other is under repair.

Two Independent Refrigerant CircuitsUWA63J AY 1 — 10 9J AY 1UWA70J ATJ — 122 J ATJUWA120J Y 1 — 270 J Y 1

Air Cooled Water Chillers

Air

Coo

led

Wat

er C

hill

ers

Air

Coo

led

Wat

er C

hill

ers

1718

19 20

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Low Power Consumption

C ontinuous capacity control with a range from 10(12)% to 100% helps to reduce energy wastage during low-load

UWY P 40 — 160B Y 1 UWY P 40 — 120B Y BUWY 40 — 120AY 1 UWY 40 — 120AY B

UWY P 40 — 160B Y 1 UWY P 40 — 120B Y B

UWA40 — 160AY 1 UWA40 — 120AY B

High Precision

10

9

8

7

Upper Limit S ignal

Water Temp. ( )

E xample of Outlet Water Temperature C ontrol

If outlet water temperature rises above the upper limit s ignal, the load starts to increase in 10% increments

As the temperature falls below the upper limit s ignal, the load increase increments are reduced to 5% .

As the temperature falls below the set value, the load increase increments remain at 5% .

When changes in outlet water temperature become 1 or less , the thermostat is turned off.

Value S et

The outlet water temperature is precisely controlled to within 0.5 (with a s table load) through the use of electric expansion

: UW Y P S eries : UW Y S eries

New RefrigerantUWY P 125 — 750AY 3 UWY P 40 — 480B Y 1UWY P 40 — 120B Y B

E mploys the new refrigerant R -407C .

Efficient and Reliable Compressors

To improve their operational reliability, 40 -- 480HP models are equipped with semi-hermetic s ingle screw compressors .

Applies to All Models

R efrigerant inlet

R efrigerant outlet

S emi-hermetic s ingle screw compressor

UWY P 40 — 160B Y 1 UWY P 40 — 120B Y B

UWY 40 — 160AY 1 UWY 40 — 120AY B

UWY P 100 — 480B Y 1 UWY P 100 — 120B Y B

Duty cycling control equalizes the operating time of the

UWY 100 — 480AY 1

UWY 40 — 160AY 1

A choice of three control systems is available.

Outflow water temperature controlProvides precise control of the water temperature.

Compressor count controlControls the number of compressors operating depending on the load.

Inflow water temperature controlPerforms duty cycling control.

UWY 100 — 120AY B

UWY P 40 — 160B Y 1UWY 40 — 480AY BUWY P 40 — 120B Y B

C ontinues operation to levels as low as 12% of total ca-pacity to provide stable wa-ter temperature control even during low-load periods .

This mode can be used to reduce power consumption if highly precise water tempera-ture control is not necessary during low- load periods . It shuts down the compressor when the load drops below 40% .

High-P rec is ion Mode Low-P ower Mode

Multiple Operating Modes

The user can select to give priority to either precis ion or reduced power consumption.

Capacity Control Mode

The maximum current level of the compressor can be specified in order to control demand for power. S ince this function allows setting of the upper limit current value, comfortable operation is maintained while effectively controlling demand. In contrast to conventional capacity control s tep limit s ys tems , maximum capacity is maintained at the des ired demand value.

C urrent Demand Func tion

Demand Mode

Users can select the operating mode that best matches the heat source application.

Note: Switching between the above modes is accomplished using a control on the outdoor unit.

Note: Water supply piping must be purchased separately. (UWYP375AY3 — 750AY3)

UWY P 40 — 480B Y 1 UWY P 40 — 120B Y B

UWY 40 — 120AY 1 UWY 40 — 120AY B

Wide Operation Range

Note: Measures to protect against drain water freezing are necessary in cold re-gions where the highest temperature stays below 0 on several consecutive days.

A new defrosting system makes poss ible heating operation even when the outdoor temperature is as low as -15 .

C apacityOutdoor Air Temperature R ange where C ooling P oss ible

Models E mploying R -407C Models E mploying R -22

5 — 30

40 — 480

-15 to 43

-5 to 43 -5 to 43

—

UWY P 40 — 480B Y 1 UWY P 40 — 120B Y B

UWY 40 — 480AY 1 UWY 40 — 120AY B

UWY P 40 — 480B Y 1 UWY P 40 — 120B Y B

UWY 40 — 480AY 1 UWY 40 — 120AY B

Applies to All Models

Refrigerant Inlet

Refrigerant Outlet

Water Outlet

Heat Exchanger with Stainless Steel Plates

S tainles s s teel heat ex-changer plates prevent rust, thereby improving their du-rability and the system's operational reliability.

ReliabilityApplies to All Models

Easy Installation

Defrosting is performed under computer control as part of continuous capacity control, resulting in s table heating performance.

The system detects ice formation by constantly monitoring the outdoor tempera-ture, the pressures of the high- and low-pressure components, and the timers. In addition, continuous capacity control allows smooth control of capacity even af-ter a rise in the pressure of the high-pressure components. Remaining ice is melted a little at a time, and stable heating performance is maintained.

The compact des ign of these units s ignificantly reduces the space required for installation.

In the outdoor unit, component parts of a small size have been used wherever possible to reduced its size and correspondingly reduce how much space it re-quires. Furthermore, replacing the 2-way refrigerant inlets with 4-way inlets has reduced the amount of space the outdoor unit needs even further.

UWY P 125 — 750AY 3The horizontal linkup des ign increases installation flexibility.

This design ensures the installation does not protrude so far, making it possible to install water chillers along a wall or under a roof overhang.

Air heat exchangers employ fins with acrylic coating for superior durability.

50/60Hz50Hz60Hz50Hz60Hz

R-407C

R-22

Standard Unit

Standard Unit

Refrigerant Units series Model No.

UWYP—AY3UWYP—BY1UWYP—BYBUWY—AY1UWY—AYB

Capacity (kW)

2121, 22

222324

page6.7/7.5

—————

11.2/12.5125————

17/19190————

22.4/25250————

33.5/37.5375————

45/50500————

56/63630————

67/75750————

106—40404040

132—50505050

160—60606060

212—80—8080

265—

100100100100

50Hz60Hz50Hz60Hz

R-407C

R-22

Standard Unit

Standard Unit

Refrigerant Units series Model No.

UWYP—BY1UWYP—BYBUWY—AY1UWY—AYB

Capacity (kW)

21, 22222324

page315120120120120

370140—

140—

420160—

160—

480180—

180—

530200—

200—

580220—

220—

630240—

240—

740280—

280—

840320—

320—

960360—

360—

1060400—

400—

1160440—

440—

1260480—

480—

Model Lineup

UWY P 750AY 3 UWY P 120B Y 1 UWY P 180B Y 1

Air Cooled Water Chillers - Heat Pump Type

19 20

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Low Power Consumption

C ontinuous capacity control with a range from 10(12)% to 100% helps to reduce energy wastage during low-load

UWY P 40 — 160B Y 1 UWY P 40 — 120B Y BUWY 40 — 120AY 1 UWY 40 — 120AY B

UWY P 40 — 160B Y 1 UWY P 40 — 120B Y B

UWA40 — 160AY 1 UWA40 — 120AY B

High Precision

10

9

8

7

Upper Limit S ignal

Water Temp. ( )

E xample of Outlet Water Temperature C ontrol

If outlet water temperature rises above the upper limit s ignal, the load starts to increase in 10% increments

As the temperature falls below the upper limit s ignal, the load increase increments are reduced to 5% .

As the temperature falls below the set value, the load increase increments remain at 5% .

When changes in outlet water temperature become 1 or less , the thermostat is turned off.

Value S et

The outlet water temperature is precisely controlled to within 0.5 (with a s table load) through the use of electric expansion

: UW Y P S eries : UW Y S eries

New RefrigerantUWY P 125 — 750AY 3 UWY P 40 — 480B Y 1UWY P 40 — 120B Y B

E mploys the new refrigerant R -407C .

Efficient and Reliable Compressors

To improve their operational reliability, 40 -- 480HP models are equipped with semi-hermetic s ingle screw compressors .

Applies to All Models

R efrigerant inlet

R efrigerant outlet

S emi-hermetic s ingle screw compressor

UWY P 40 — 160B Y 1 UWY P 40 — 120B Y B

UWY 40 — 160AY 1 UWY 40 — 120AY B

UWY P 100 — 480B Y 1 UWY P 100 — 120B Y B

Duty cycling control equalizes the operating time of the

UWY 100 — 480AY 1

UWY 40 — 160AY 1

A choice of three control systems is available.

Outflow water temperature controlProvides precise control of the water temperature.

Compressor count controlControls the number of compressors operating depending on the load.

Inflow water temperature controlPerforms duty cycling control.

UWY 100 — 120AY B

UWY P 40 — 160B Y 1UWY 40 — 480AY BUWY P 40 — 120B Y B

C ontinues operation to levels as low as 12% of total ca-pacity to provide stable wa-ter temperature control even during low-load periods .

This mode can be used to reduce power consumption if highly precise water tempera-ture control is not necessary during low- load periods . It shuts down the compressor when the load drops below 40% .

High-P rec is ion Mode Low-P ower Mode

Multiple Operating Modes

The user can select to give priority to either precis ion or reduced power consumption.

Capacity Control Mode

The maximum current level of the compressor can be specified in order to control demand for power. S ince this function allows setting of the upper limit current value, comfortable operation is maintained while effectively controlling demand. In contrast to conventional capacity control s tep limit s ys tems , maximum capacity is maintained at the des ired demand value.

C urrent Demand F unc tion

Demand Mode

Users can select the operating mode that best matches the heat source application.

Note: Switching between the above modes is accomplished using a control on the outdoor unit.

Note: Water supply piping must be purchased separately. (UWYP375AY3 — 750AY3)

UWY P 40 — 480B Y 1 UWY P 40 — 120B Y B

UWY 40 — 120AY 1 UWY 40 — 120AY B

Wide Operation Range

Note: Measures to protect against drain water freezing are necessary in cold re-gions where the highest temperature stays below 0 on several consecutive days.

A new defrosting system makes poss ible heating operation even when the outdoor temperature is as low as -15 .

C apacityOutdoor Air Temperature R ange where C ooling P oss ible

Models E mploying R -407C Models E mploying R -22

5 — 30

40 — 480

-15 to 43

-5 to 43 -5 to 43

—

UWY P 40 — 480B Y 1 UWY P 40 — 120B Y B

UWY 40 — 480AY 1 UWY 40 — 120AY B

UWY P 40 — 480B Y 1 UWY P 40 — 120B Y B

UWY 40 — 480AY 1 UWY 40 — 120AY B

Applies to All Models

Refrigerant Inlet

Refrigerant Outlet

Water Outlet

Heat Exchanger with Stainless Steel Plates

S tainles s s teel heat ex-changer plates prevent rust, thereby improving their du-rability and the system's operational reliability.

ReliabilityApplies to All Models

Easy Installation

Defrosting is performed under computer control as part of continuous capacity control, resulting in s table heating performance.

The system detects ice formation by constantly monitoring the outdoor tempera-ture, the pressures of the high- and low-pressure components, and the timers. In addition, continuous capacity control allows smooth control of capacity even af-ter a rise in the pressure of the high-pressure components. Remaining ice is melted a little at a time, and stable heating performance is maintained.

The compact des ign of these units s ignificantly reduces the space required for installation.

In the outdoor unit, component parts of a small size have been used wherever possible to reduced its size and correspondingly reduce how much space it re-quires. Furthermore, replacing the 2-way refrigerant inlets with 4-way inlets has reduced the amount of space the outdoor unit needs even further.

UWY P 125 — 750AY 3The horizontal linkup des ign increases installation flexibility.

This design ensures the installation does not protrude so far, making it possible to install water chillers along a wall or under a roof overhang.

Air heat exchangers employ fins with acrylic coating for superior durability.

50/60Hz50Hz60Hz50Hz60Hz

R-407C

R-22

Standard Unit

Standard Unit

Refrigerant Units series Model No.

UWYP—AY3UWYP—BY1UWYP—BYBUWY—AY1UWY—AYB

Capacity (kW)

2121, 22

222324

page6.7/7.5

—————

11.2/12.5125————

17/19190————

22.4/25250————

33.5/37.5375————

45/50500————

56/63630————

67/75750————

106—40404040

132—50505050

160—60606060

212—80—8080

265—

100100100100

50Hz60Hz50Hz60Hz

R-407C

R-22

Standard Unit

Standard Unit

Refrigerant Units series Model No.

UWYP—BY1UWYP—BYBUWY—AY1UWY—AYB

Capacity (kW)

21, 22222324

page315120120120120

370140—

140—

420160—

160—

480180—

180—

530200—

200—

580220—

220—

630240—

240—

740280—

280—

840320—

320—

960360—

360—

1060400—

400—

1160440—

440—

1260480—

480—

Model Lineup

UWY P 750AY 3 UWY P 120B Y 1 UWY P 180B Y 1

Air Cooled Water Chillers - Heat Pump Type

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

530 — 1,260kW class

UWY P 200 — 480B Y 1Standard Unit

50Hz

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 The unit is equipped with standard water filter. *5 The limited length of wire represents its max. length when the pressure is lower than 2%. *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

Water inlet/outletDrain outlet

UWYP200BY1(200 )

UWYP220BY1(220 )

UWYP240BY1(240 )

UWYP280BY1(280 )

UWYP320BY1(320 )

UWYP360BY1(360 )

UWYP480BY1(480 )

UWYP400BY1(400 )

UWYP440BY1(440 )Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections Dimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

5301,809,000 151 1,519 5701,945,000 162 3 phase, 50 Hz 380/400/415 V, 4 wires system 1,634 100~10-0Semi-hermetic sealed single-screw type45 2+60Brazing Plate type Cross fin coil Propeller Direct drive 3,010106,2531.0 14R-407C5B Flange (125A HG20593-97)RP1 1/4 Female screw (32A)2,456 7,050 2,000 6,8207,018cooling -5 to 43, heating -20 to 21

5801,979,000 165 1,663 6302,150,000 179

1,806

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0007,5007,719

6302,150,000 179 1,806 6902,355,000 196

1,978

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,8858,125

7402,525,000 210 2,121 8002,730,000 228

2,293

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97)

(2,456 4,850 2,000) 24,553 24,624 2

8402,867,000 239 2,408 9203,140,000 262

2,637

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 25,110 25,181 2

9603,276,000 273 2,752 1,0203,481,000 290

2,924

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 26,265 26,456 2

1,0603,617,000 301 3,039 1,1403,890,000 324

3,268

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 26,820 27,018 2

1,1603,959,000 330 3,325 1,2604,300,000 358

3,612

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 27,500 27,719 2

1,2604,300,000 358 3,612 1,3804,710,000 392

3,956

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 27,885 28,125 2

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

Water inlet/outletDrain outlet

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections water inlet/outlet Dimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

118 — 355kW class

UWY P 40 — 120B Y BStandard Unit

60Hz

UWYP40BYB(40 )

UWYP50BYB(50 )

UWYP60BYB(60 )

UWYP100BYB(100 )

UWYP120BYB(120 )

118403,000 34 338 132450,000 38 3 phase,60 Hz 400/440 V, 3 wires system378 100~10-0Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive81028,5930.5 4 R-407C3B Flange (80A HG20593-97) RP1 1/4 Female screw (32A)2,456 2,200 2,0001,6901,723cooling -5 to 43, heating -20 to 21

150512,000 43 430 170580,000 48

487

37 1

1,01035,6531.0 4

1,8101,846

180614,000 51 516 200683,000 57

573

45 1

1,8701,910

3001,024,000 85 860 3351,143,000 95

960

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5003,551

3551,212,000 101 1,018 4001,365,000 114

1,147

45 2

3,6053,662

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 The unit is equipped with standard water filter. *5 The limited length of wire represents its max. length when the pressure is lower than 2%. *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

Water inlet/outlet

Drain outlet

UWYP40BY1(40 )

UWYP50BY1(50 )

UWYP60BY1(60 )

UWYP80BY1(80 )

UWYP100BY1(100 )

UWYP120BY1(120 )

UWYP180BY1(180 )

UWYP140BY1(140 )

UWYP160BY1(160 )Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

106 — 480kW class

UWY P 40 — 180B Y 1Standard Unit

50Hz

106362,000 30 304 112382,000 32 3 phase,50 Hz 380/400/415 V, 4wires system 321100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

RP1 1/4 Female screw (32A)2,456 2,200 2,0001,8001,833cooling -5 to 43, heating -20 to 21

132450,000 38 378 140478,000 40

401

37 1

86030,3581.0 4

1,9301,966

160546,000 46 459 170580,000 48

487

45 1

1,9902,030

210717,000 60 602 230785,000 65

659

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,6402,687

265904,000 75 760 280956,000 80

803

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,7403,791

3151,075,000 90 9033401,160,000 97

975

45 2

1,72060,716

3,9954,052

3701,263,000 105 1,061 4001,365,000 114

1,147

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,5534,624

4201,433,000 119 1,204 4601,570,000 131

1,319

60 2

2,58091,0741.0 12

2,456 5,300 2,0005,1105,181

4801,638,000 137 1,376 5101,740,000 145

1,462

45 3

5B Flange (125A HG20593-97)

2,456 6,600 2,0006,2656,456

S pecifications

11.2 / 12.5 — 67 / 75 kW class

UWY P 125 — 750AY 3Standard Unit

50/60Hz

Model

Cooling capacity(50/60 Hz)

Chilled water flow rate (50/60 Hz)

Heating capacity(50/60 Hz)

Power supplyHot water flow rate (50/60 Hz)Capacity steps

Compressor

Evaporator typeCondenser type

Fan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDriveAir flow rate(50/60 Hz)Motor output

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

UWYP125AY3(5 )

UWYP190AY3(8 )

UWYP250AY3(10 )

UWYP375AY3(15 )

UWYP500AY3(20 )

UWYP630AY3(25 )

UWYP750AY3(30 )

22.4/25.076,500/85,4006.37/7.1164/7225.0/28.085,400/95,6007.11/7.96

72/80

7.5 1

175/1856,180/6,5300.22 2

260264

17.0/19.058,000/64,9004.83/5.4049/5420.0/22.468,300/76,5005.69/6.37

57/64

5.5 1

140/1604,940/5,6500.22+0.14

1 1/2B Fiange(JIS10K)(40A) 2

1,450 1,280 690258261

33.5/37.5114,000/128,0009.53/10.796/10837.5/42.5128,000/145,00010.7/12.1

108/122100-67-34-0

7.5+3.75

265/2809,350/9,8800.22 2+0.20

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 21,500 1,925 690420427

45.0/50.0154,000/171,00012.8/14.2129/14350.0/56.0171,000/191,00014.2/15.9

143/161100-50-0

7.5 2

350/37012,400/13,1000.22 4

1 1/2B Flange(JIS10K)(40A) 4

1,500 2,570 690525535

56.0/63.0191,000/215,00015.9/17.9161/18163.0/71.0215,000/242,00017.9/20.2

181/204100-80-60-40-20-0

7.5 2+3.75

440/46515,500/16,4000.22 4+0.20

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 41,550 3,230 758700715

67.0/75.0229,000/256,00019.1/21.3192/21575.0/85.0256,000/290,00021.3/24.2

215/244100-67-34-0

7.5 3

525/55518,500/19,6000.22 6

1 1/2B Flange(JIS10K)(40A) 6

1,550 3,870 758820840

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp. 40 (104 F), and outdoor air temp. 7 DB(44.5 FDB), and

6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure switch. • Reverse-phase protector. • Fusible plug. • Freeze up thermostat. • Overcurrent relay for compressor

and fan motor. • Overheat protection for discharge gas. • fan thermal protector.*4 This product is manufactured in Japan.

*1

*2

11.2/12.538,200/42,7003.19/3.5532/3613.2/15.045,100/51,2003.75/4.273 phase, 50 Hz 380/400/415 V, 60 Hz 400/440 V, 3 wires system 38/43100-0Hermetically sealed scroll type3.75 1Brazed plate heat exchangerCross fin coilPropellerDirect drive90/953,180/3,3500.20R-407C

1B Flange (JIS10K)(25A) 2

1,450 635 (839) 690150152-15 to 43 in cooling, -15 to 21 in heating

Air Cooled Water Chillers - Heat Pump Type

21 22

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

530 — 1,260kW class

UWY P 200 — 480B Y 1Standard Unit

50Hz

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 The unit is equipped with standard water filter. *5 The limited length of wire represents its max. length when the pressure is lower than 2%. *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

Water inlet/outletDrain outlet

UWYP200BY1(200 )

UWYP220BY1(220 )

UWYP240BY1(240 )

UWYP280BY1(280 )

UWYP320BY1(320 )

UWYP360BY1(360 )

UWYP480BY1(480 )

UWYP400BY1(400 )

UWYP440BY1(440 )Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections Dimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

5301,809,000 151 1,519 5701,945,000 162 3 phase, 50 Hz 380/400/415 V, 4 wires system 1,634 100~10-0Semi-hermetic sealed single-screw type45 2+60Brazing Plate type Cross fin coil Propeller Direct drive 3,010106,2531.0 14R-407C5B Flange (125A HG20593-97)RP1 1/4 Female screw (32A)2,456 7,050 2,000 6,8207,018cooling -5 to 43, heating -20 to 21

5801,979,000 165 1,663 6302,150,000 179

1,806

45+60 2

3,440121,4321.0 16

2,456 7,500 2,0007,5007,719

6302,150,000 179 1,806 6902,355,000 196

1,978

60 3

3,870136,6111.0 18

2,456 7,950 2,0007,8858,125

7402,525,000 210 2,121 8002,730,000 228

2,293

(45+60) 2

4,300151,790(1.0 10) 2

4B Flange (100A HG20593-97)

(2,456 4,850 2,000) 24,553 24,624 2

8402,867,000 239 2,408 9203,140,000 262

2,637

(60 2) 2

5,160182,148(1.0 12) 2

(2,456 5,300 2,000) 25,110 25,181 2

9603,276,000 273 2,752 1,0203,481,000 290

2,924

(45 3) 2

5B Flange (125A HG20593-97)

(2,456 6,600 2,000) 26,265 26,456 2

1,0603,617,000 301 3,039 1,1403,890,000 324

3,268

(45 2+60) 2

6,020212,506(1.0 14) 2

(2,456 7,050 2,000) 26,820 27,018 2

1,1603,959,000 330 3,325 1,2604,300,000 358

3,612

(45+60 2) 2

6,880242,864(1.0 16) 2

(2,456 7,500 2,000) 27,500 27,719 2

1,2604,300,000 358 3,612 1,3804,710,000 392

3,956

(60 3) 2

7,740273,222(1.0 18) 2

(2,456 7,950 2,000) 27,885 28,125 2

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

Water inlet/outletDrain outlet

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

RefrigerantPipe connections water inlet/outlet Dimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

118 — 355kW class

UWY P 40 — 120B Y BStandard Unit

60Hz

UWYP40BYB(40 )

UWYP50BYB(50 )

UWYP60BYB(60 )

UWYP100BYB(100 )

UWYP120BYB(120 )

118403,000 34 338 132450,000 38 3 phase,60 Hz 400/440 V, 3 wires system378 100~10-0Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive81028,5930.5 4 R-407C3B Flange (80A HG20593-97) RP1 1/4 Female screw (32A)2,456 2,200 2,0001,6901,723cooling -5 to 43, heating -20 to 21

150512,000 43 430 170580,000 48

487

37 1

1,01035,6531.0 4

1,8101,846

180614,000 51 516 200683,000 57

573

45 1

1,8701,910

3001,024,000 85 860 3351,143,000 95

960

37 2

2,02071,3061.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,5003,551

3551,212,000 101 1,018 4001,365,000 114

1,147

45 2

3,6053,662

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 The unit is equipped with standard water filter. *5 The limited length of wire represents its max. length when the pressure is lower than 2%. *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

Water inlet/outlet

Drain outlet

UWYP40BY1(40 )

UWYP50BY1(50 )

UWYP60BY1(60 )

UWYP80BY1(80 )

UWYP100BY1(100 )

UWYP120BY1(120 )

UWYP180BY1(180 )

UWYP140BY1(140 )

UWYP160BY1(160 )Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

CondenserFans

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

106 — 480kW class

UWY P 40 — 180B Y 1Standard Unit

50Hz

106362,000 30 304 112382,000 32 3 phase,50 Hz 380/400/415 V, 4wires system 321100~10-0 Semi-hermetic sealed single-screw type30 1Brazing Plate type Cross fin coil Propeller Direct drive78027,5340.5 4R-407C

3B Flange (80A HG20593-97)

RP1 1/4 Female screw (32A)2,456 2,200 2,0001,8001,833cooling -5 to 43, heating -20 to 21

132450,000 38 378 140478,000 40

401

37 1

86030,3581.0 4

1,9301,966

160546,000 46 459 170580,000 48

487

45 1

1,9902,030

210717,000 60 602 230785,000 65

659

60 1

1,29045,5371.0 6

2,456 2,650 2,0002,6402,687

265904,000 75 760 280956,000 80

803

37 2

1,60056,4801.0 8

4B Flange (100A HG20593-97)

2,456 4,400 2,0003,7403,791

3151,075,000 90 9033401,160,000 97

975

45 2

1,72060,716

3,9954,052

3701,263,000 105 1,061 4001,365,000 114

1,147

45+60

2,15075,8951.0 10

2,456 4,850 2,0004,5534,624

4201,433,000 119 1,204 4601,570,000 131

1,319

60 2

2,58091,0741.0 12

2,456 5,300 2,0005,1105,181

4801,638,000 137 1,376 5101,740,000 145

1,462

45 3

5B Flange (125A HG20593-97)

2,456 6,600 2,0006,2656,456

S pecifications

11.2 / 12.5 — 67 / 75 kW class

UWY P 125 — 750AY 3Standard Unit

50/60Hz

Model

Cooling capacity(50/60 Hz)

Chilled water flow rate (50/60 Hz)

Heating capacity(50/60 Hz)

Power supplyHot water flow rate (50/60 Hz)Capacity steps

Compressor

Evaporator typeCondenser type

Fan

Refrigerant

Pipe connections water inlet/outlet

Dimensions (H W D)WeightOperating weightOperation range

TypeMotor output

TypeDriveAir flow rate(50/60 Hz)Motor output

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

UWYP125AY3(5 )

UWYP190AY3(8 )

UWYP250AY3(10 )

UWYP375AY3(15 )

UWYP500AY3(20 )

UWYP630AY3(25 )

UWYP750AY3(30 )

22.4/25.076,500/85,4006.37/7.1164/7225.0/28.085,400/95,6007.11/7.96

72/80

7.5 1

175/1856,180/6,5300.22 2

260264

17.0/19.058,000/64,9004.83/5.4049/5420.0/22.468,300/76,5005.69/6.37

57/64

5.5 1

140/1604,940/5,6500.22+0.14

1 1/2B Fiange(JIS10K)(40A) 2

1,450 1,280 690258261

33.5/37.5114,000/128,0009.53/10.796/10837.5/42.5128,000/145,00010.7/12.1

108/122100-67-34-0

7.5+3.75

265/2809,350/9,8800.22 2+0.20

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 21,500 1,925 690420427

45.0/50.0154,000/171,00012.8/14.2129/14350.0/56.0171,000/191,00014.2/15.9

143/161100-50-0

7.5 2

350/37012,400/13,1000.22 4

1 1/2B Flange(JIS10K)(40A) 4

1,500 2,570 690525535

56.0/63.0191,000/215,00015.9/17.9161/18163.0/71.0215,000/242,00017.9/20.2

181/204100-80-60-40-20-0

7.5 2+3.75

440/46515,500/16,4000.22 4+0.20

1B Flange (JIS10K)(25A) 2+1 1/2B Flange(JIS10K)(40A) 41,550 3,230 758700715

67.0/75.0229,000/256,00019.1/21.3192/21575.0/85.0256,000/290,00021.3/24.2

215/244100-67-34-0

7.5 3

525/55518,500/19,6000.22 6

1 1/2B Flange(JIS10K)(40A) 6

1,550 3,870 758820840

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp. 40 (104 F), and outdoor air temp. 7 DB(44.5 FDB), and

6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure switch. • Reverse-phase protector. • Fusible plug. • Freeze up thermostat. • Overcurrent relay for compressor

and fan motor. • Overheat protection for discharge gas. • fan thermal protector.*4 This product is manufactured in Japan.

*1

*2

11.2/12.538,200/42,7003.19/3.5532/3613.2/15.045,100/51,2003.75/4.273 phase, 50 Hz 380/400/415 V, 60 Hz 400/440 V, 3 wires system 38/43100-0Hermetically sealed scroll type3.75 1Brazed plate heat exchangerCross fin coilPropellerDirect drive90/953,180/3,3500.20R-407C

1B Flange (JIS10K)(25A) 2

1,450 635 (839) 690150152-15 to 43 in cooling, -15 to 21 in heating

Air Cooled Water Chillers - Heat Pump Type

21 22

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

UWYP40AY1UWYP50AY1UWYP60AY1

UWYP80AY1 UWYP100AY1UWYP120AY1UWYP140AY1UWYP160AY1

UWYP180AY1UWYP200AY1UWYP220AY1UWYP240AY1

UWYP280AY1UWYP320AY1

UWYP380AY1UWYP400AY1UWYP440AY1UWYP480AY1

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP40BGWP-UWYP40BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWP-UWYP80BGWEL-UWYP100BGWP-UWYP100B

GWEL-UWYP180BGWP-UWYP180B

GWEL-UWYP280BGWP-UWYP280B

GWEL-UWYP360BGWP-UWYP360B

Option L is tUWYP40BY1UWYP50BY1UWYP60BY1UWYP40BYBUWYP50BYBUWYP60BYB

UWYP80BY1 UWYP100BY1UWYP120BY1UWYP140BY1UWYP160BY1UWYP100BYBUWYP120BYB

UWYP180BY1UWYP200BY1UWYP220BY1UWYP240BY1

UWYP280BY1UWYP320BY1

UWYP360BY1UWYP400BY1UWYP440BY1UWYP480BY1

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP40BGWP-UWYP40BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWP-UWYP80BGWEL-UWYP100BGWP-UWYP100B

GWEL-UWYP180BGWP-UWYP180B

GWEL-UWYP280BGWP-UWYP280B

GWEL-UWYP360BGWP-UWYP360B

UWYP125AY3 UWYP190AY3 UWYP250AY3 UWYP375AY3 UWYP500AY3 UWYP630AY3 UWYP750AY3

Notes: *1 Communication I/F P.C. board, Communication I/F P.C. B storage box and Transmission waire are also required.

Remote controller *1Communication I/F P.C. boardCommunication I/F P.C. B storage boxTransmission wire

ModelBRC307C50BRP66B3BPR66A97BER66A5

BPR66A100BER66A7

—

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 The unit is equipped with standard water filter. *5 The limited length of wire represents its max. length when the pressure is lower than 2%. *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

*1

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connectionswater inlet/outletDimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

*2

118 — 355kW class

UWY 40 — 120AY BStandard Unit

60Hz

UWY40AYB(40 )

UWY50AYB(50 )

UWY60AYB(60 )

UWY100AYB(100 )

UWY120AYB(120 )

118403,00034338132450,000383 phase, 60 Hz 400/440 V, 3 wires system378100~10-0Semi-hermetic sealed single-screw type30 1Blazing Plate typeCross fin coilPropellerDirect drive80028,2400.5 4R-22

3B Flange (80A HG20593-97)

2,395 2,200 2,0001,7001,717cooling -5 to 43, heating -20 to 21

150512,00043430170580,00048

487

37 1

81028,5930.8 4

1,8001,820

180614,00051516200683,00057

573

45 1

94033,1821.2 4

1,9501,973

3001,024,000858603351,143,00095

960

37 2

1,62057,1860.8 8

4B Flange (100A HG20593-97)

2,395 4,400 2,0003,6003,636

3551,212,0001011,0184001,365,000114

1,147

45 2

1,88066,3641.2 8

3,9003,942

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required. *5 Installation/operating weight includes the weight of refrigerant and refrigerant oil(charged before delivery).

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWY200AY1(200 )

UWY220AY1(220 )

UWY240AY1(240 )

UWY280AY1(280 )

UWY320AY1(320 )

UWY360AY1(360 )

UWY480AY1(480 )

UWY400AY1(400 )

UWY420AY1(420 )

*1

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections Water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mm

kgkg

6302,150,0001791,8067202,457,000205

2,064

60 3

2,82099,546

6,3506,450

7402,525,0002102,1218402,867,000239

2,408

(45+60) 2

3,560125,668(1.2 8) 2

4B Flange (100A HG20593-97)

(2,395 4,400 2,000) 2

4,020 24,084 2

5301,809,0001511,5196002,048,0001713 phase, 50 Hz 380/400/415 V, 4 wires system 1,720100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type45 2+60Blazing plate typeCross fin coilPropellerDirect drive2,62092,4861.2 12R-225B Flange (125A HG20593-97)

(2,460 6,600 2,000) 2

6,2606,337cooling -5 to 43, heating -20 to 21

*2

5801,979,0001651,6636602,252,000188

1,892

45+60 2

2,72096,016

6,2956,382

8402,867,0002392,4089603,276,000273

2,752

(60 2) 2

3,760132,728

4,040 24,104 2

9603,276,0002732,7521,0803,686,000307

3,096

(45 3) 2

5,040177,912(1.2 12) 2

5B Flange (125A HG20593-97)

(2,460 6,600 2,000) 2

6,205 26,270 2

1,0603,617,0003013,0391,2004,095,000341

3,440

(45 2+60) 2

5,240184,972

6,260 26,337 2

1,2604,300,0003583,6121,4404,914,000410

4,128

(60 3) 2

5,640199,092

6,350 26,450 2

1,1603,959,0003303,3251,3204,505,000375

3,784

(45+60 2) 2

5,440192,032

6,295 26,382 2

530 — 1,260kW class

UWY 200 — 480AY 1Standard Unit

50Hz

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heatinging capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required. *5 Installation/operating weight includes the weight of refrigerant and refrigerant oil (charged before delivery). *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWY40AY1(40 )

UWY50AY1(50 )

UWY60AY1(60 )

UWY80AYAY1(80 )

UWY100AY1(100 )

UWY120AY1(120 )

UWY180AY1(180 )

UWY140AY1(140 )

UWY160AY1(160 )

*1

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mm

kgkg

160546,00046459180614,00051

516

45 1

84029,6521.2 4

1,9501,973

210717,00060602240819,00068

688

60 1

94033,182

2,0202,052

106362,00030304118403,000343 phase, 50 Hz 380/400/415 V, 4 wires system 338100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type30 1Brazed plate typeCross fin coilPropellerDirect drive70024,7100.5 4R-223B Flange (80A HG20593-97)

2,395 2,200 2,000

1,7001,717cooling -5 to 43, heating -20 to 21

*2

132450,00038378150512,00043

430

37 1

71025,0630.8 4

1,8001,820

265904,000757603001,024,00085

860

37 2

1,42050,1260.8 8

4B Flange (100A HG20593-97)

2,395 4,400 2,000

3,6003,636

3201,092,000919173551,212,000101

1,018

45 2

1,68059,3041.2 8

3,9003,942

3701,263,0001051,0614201,433,000119

1,204

45+60

1,78062,834

4,0204,084

4801,638,0001371,3765401,843,000154

1,548

45 3

2,52088,9561.2 12

5B Flange (125A HG20593-97) 2,460 6,600 2,0006,2056,270

4201,433,0001191,2044801,638,000137

1,376

60 2

1,88066,364

4,0404,104

106 — 480kW class

UWY 40 — 180AY 1Standard Unit

50Hz

Air Cooled Water Chillers - Heat Pump Type

23 24

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

Air

Coo

led

Wat

er C

hill

ers

- Hea

t Pum

p Ty

pe

UWYP40AY1UWYP50AY1UWYP60AY1

UWYP80AY1 UWYP100AY1UWYP120AY1UWYP140AY1UWYP160AY1

UWYP180AY1UWYP200AY1UWYP220AY1UWYP240AY1

UWYP280AY1UWYP320AY1

UWYP380AY1UWYP400AY1UWYP440AY1UWYP480AY1

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP40BGWP-UWYP40BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWP-UWYP80BGWEL-UWYP100BGWP-UWYP100B

GWEL-UWYP180BGWP-UWYP180B

GWEL-UWYP280BGWP-UWYP280B

GWEL-UWYP360BGWP-UWYP360B

Option L is tUWYP40BY1UWYP50BY1UWYP60BY1UWYP40BYBUWYP50BYBUWYP60BYB

UWYP80BY1 UWYP100BY1UWYP120BY1UWYP140BY1UWYP160BY1UWYP100BYBUWYP120BYB

UWYP180BY1UWYP200BY1UWYP220BY1UWYP240BY1

UWYP280BY1UWYP320BY1

UWYP360BY1UWYP400BY1UWYP440BY1UWYP480BY1

Model

Remote controllerChilling water supply interrupting relayWater high pressure (1.6 MPa) upgraderIPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timer

BRC307D503GWEL-UWYP40BGWP-UWYP40BDAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61

GWP-UWYP80BGWEL-UWYP100BGWP-UWYP100B

GWEL-UWYP180BGWP-UWYP180B

GWEL-UWYP280BGWP-UWYP280B

GWEL-UWYP360BGWP-UWYP360B

UWYP125AY3 UWYP190AY3 UWYP250AY3 UWYP375AY3 UWYP500AY3 UWYP630AY3 UWYP750AY3

Notes: *1 Communication I/F P.C. board, Communication I/F P.C. B storage box and Transmission waire are also required.

Remote controller *1Communication I/F P.C. boardCommunication I/F P.C. B storage boxTransmission wire

ModelBRC307C50BRP66B3BPR66A97BER66A5

BPR66A100BER66A7

—

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 The unit is equipped with standard water filter. *5 The limited length of wire represents its max. length when the pressure is lower than 2%. *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

*1

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connectionswater inlet/outletDimensions (H W D)WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mmkgkg

*2

118 — 355kW class

UWY 40 — 120AY BStandard Unit

60Hz

UWY40AYB(40 )

UWY50AYB(50 )

UWY60AYB(60 )

UWY100AYB(100 )

UWY120AYB(120 )

118403,00034338132450,000383 phase, 60 Hz 400/440 V, 3 wires system378100~10-0Semi-hermetic sealed single-screw type30 1Blazing Plate typeCross fin coilPropellerDirect drive80028,2400.5 4R-22

3B Flange (80A HG20593-97)

2,395 2,200 2,0001,7001,717cooling -5 to 43, heating -20 to 21

150512,00043430170580,00048

487

37 1

81028,5930.8 4

1,8001,820

180614,00051516200683,00057

573

45 1

94033,1821.2 4

1,9501,973

3001,024,000858603351,143,00095

960

37 2

1,62057,1860.8 8

4B Flange (100A HG20593-97)

2,395 4,400 2,0003,6003,636

3551,212,0001011,0184001,365,000114

1,147

45 2

1,88066,3641.2 8

3,9003,942

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heating capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required. *5 Installation/operating weight includes the weight of refrigerant and refrigerant oil(charged before delivery).

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWY200AY1(200 )

UWY220AY1(220 )

UWY240AY1(240 )

UWY280AY1(280 )

UWY320AY1(320 )

UWY360AY1(360 )

UWY480AY1(480 )

UWY400AY1(400 )

UWY420AY1(420 )

*1

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections Water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mm

kgkg

6302,150,0001791,8067202,457,000205

2,064

60 3

2,82099,546

6,3506,450

7402,525,0002102,1218402,867,000239

2,408

(45+60) 2

3,560125,668(1.2 8) 2

4B Flange (100A HG20593-97)

(2,395 4,400 2,000) 2

4,020 24,084 2

5301,809,0001511,5196002,048,0001713 phase, 50 Hz 380/400/415 V, 4 wires system 1,720100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type45 2+60Blazing plate typeCross fin coilPropellerDirect drive2,62092,4861.2 12R-225B Flange (125A HG20593-97)

(2,460 6,600 2,000) 2

6,2606,337cooling -5 to 43, heating -20 to 21

*2

5801,979,0001651,6636602,252,000188

1,892

45+60 2

2,72096,016

6,2956,382

8402,867,0002392,4089603,276,000273

2,752

(60 2) 2

3,760132,728

4,040 24,104 2

9603,276,0002732,7521,0803,686,000307

3,096

(45 3) 2

5,040177,912(1.2 12) 2

5B Flange (125A HG20593-97)

(2,460 6,600 2,000) 2

6,205 26,270 2

1,0603,617,0003013,0391,2004,095,000341

3,440

(45 2+60) 2

5,240184,972

6,260 26,337 2

1,2604,300,0003583,6121,4404,914,000410

4,128

(60 3) 2

5,640199,092

6,350 26,450 2

1,1603,959,0003303,3251,3204,505,000375

3,784

(45+60 2) 2

5,440192,032

6,295 26,382 2

530 — 1,260kW class

UWY 200 — 480AY 1Standard Unit

50Hz

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), and outdoor air temp. 35 DB(95 FDB).*2 Heatinging capacity is based on the following conditions : Leaving hot water temp.45 (113 F), entering hot water temp.40 (104 F), and outdoor air temp. 7 DB(44.5 FDB),and 6 WB(43 FWB).*3 The following safety devices are equipped as standard. • High pressure protector. • Low pressure protector. • Compressor thermal protector. • Fusible plug. • Reverse-phase

protector. • Overheat protection of discharge gas. • Overcurrent relay(compressor). • Freeze-up protection thermostat. • Overcurrent relay(fan). • Safety valve.*4 Standard for the max. chilled water pressure is 0.7MPa, but1.6MPa is available if required. *5 Installation/operating weight includes the weight of refrigerant and refrigerant oil (charged before delivery). *6 This product is manufactured in China.

S pecifications

TypeMotor output

TypeDrive

Air flow rate

Motor output

UWY40AY1(40 )

UWY50AY1(50 )

UWY60AY1(60 )

UWY80AYAY1(80 )

UWY100AY1(100 )

UWY120AY1(120 )

UWY180AY1(180 )

UWY140AY1(140 )

UWY160AY1(160 )

*1

Model

Cooling capacity

Chilled water flow rate

Heating capacity

Power supplyHot water flow rateCapacity steps

Compressor

Evaporator typeCondenser type

Condenserfan

RefrigerantPipe connections water inlet/outlet

Dimensions (H W D)

WeightOperating weightOperation range

kWBtu/hUSRT /minkWBtu/hUSRT

/min%

kW

m3/mincfmkW

mm

kgkg

160546,00046459180614,00051

516

45 1

84029,6521.2 4

1,9501,973

210717,00060602240819,00068

688

60 1

94033,182

2,0202,052

106362,00030304118403,000343 phase, 50 Hz 380/400/415 V, 4 wires system 338100~10-0 (continuous capacity control)Semi-hermetic sealed single-screw type30 1Brazed plate typeCross fin coilPropellerDirect drive70024,7100.5 4R-223B Flange (80A HG20593-97)

2,395 2,200 2,000

1,7001,717cooling -5 to 43, heating -20 to 21

*2

132450,00038378150512,00043

430

37 1

71025,0630.8 4

1,8001,820

265904,000757603001,024,00085

860

37 2

1,42050,1260.8 8

4B Flange (100A HG20593-97)

2,395 4,400 2,000

3,6003,636

3201,092,000919173551,212,000101

1,018

45 2

1,68059,3041.2 8

3,9003,942

3701,263,0001051,0614201,433,000119

1,204

45+60

1,78062,834

4,0204,084

4801,638,0001371,3765401,843,000154

1,548

45 3

2,52088,9561.2 12

5B Flange (125A HG20593-97) 2,460 6,600 2,0006,2056,270

4201,433,0001191,2044801,638,000137

1,376

60 2

1,88066,364

4,0404,104

106 — 480kW class

UWY 40 — 180AY 1Standard Unit

50Hz

Air Cooled Water Chillers - Heat Pump Type

23 24

A s ingle built- in control box s implifies operation and control.

P rovides a s table supply of chilled water throughout the

Since the heat exchanger employs water, operation of the unit is not affected by changes in the outdoor temperature. A stable water temperature is maintained year round.

All controls and indicators are centralized in a single control box, making it possi-ble to control the system using fewer personnel. Installation is simplified by inte-gration of the control box with the main unit.

The water temperature setting can be set to any value between 4 and 25 .

The 10 HP model has a footprint measuring only 0.32 square meters .

8 to 30 HP models have a modular design that enables units with different capaci-ties to be used together in a single system and simplifies increasing system ca-pacity later on 3 — 5 HP models have a similar configuration and are designed for compactness.

The starter panel is built into the control panel, s implifying

Easy InstallationUWP 90AY 3 — 900AY 3

All models are fitted with a pressure gauge as s tandard.

P erformance characteris tics under partial load are efficient.

Reliability

Efficient Performance

Well Appointed

The new double-pipe heat exchanger design reduces clogging, significantly in-creasing resistance to dirty cooling water.

The double-pipe heat exchanger and an individual error indication function help reduce the manpower required for

MaintenanceUWP 90AY 3 — 900AY 3

UWD1320DY 1 — 4000DY 1

Year Round Cooling OperationApplies to All Models

Wide Water Temperature Control Range RangeUWP 90AY 3 — 900AY 3

Simple Operation and ControlUWD1320DY 1 — 4000DY 1

UWD1320DY 1UWP 900AY 3

Model LineupRefrigerant Units series Model No.

Capacity (kW) page

50/60Hz50Hz

R-407CR-134a

Standard UnitStandard Unit

UWP—AY3UWD—DY1

8/990—

13.2/15150—

20/22.4224—

26.5/30300—

40/45450—

53/60600—

67/75750—

80/90900—

118—

1320

150—

1700

180—

2000

236—

2650

300—

3350

355—

40002727

Refrigerant Units series Model No.

50Hz60Hz50Hz60Hz

R-134aStandard Unit

Brine Cooling Unit

ZUW—AY1ZUW—AYBZUW—AY1ZZUW—AYBZ

Capacity100RT

100—

100—

120RT120120120120

150RT150150150150

175RT175175175175

200RT200200200200

240RT240240240240

280RT280280280—

300RT300—

300300

350RT350—

350—

400RT400—

400—

28282929

page

: UWP S eries : UWD S eries ZUW S eries

E mploys the new refrigerants R -407C and R -134a.

New RefrigerantUWP 90 — 900AY 3UWD1320 — 40000DY 1 ZUW100 — 400AY (1) (B ) ZUW100 — 400AY (1) (B ) Z

To improve their operational reliability, 5 -- 30HP models employ scroll compressors , while 40 -- 120HP models are equipped with semi-hermetic s ingle screw compressors .

R efrigerant inlet

R efrigerant outlet

S emi-hermetic s ingle screw compressor

Efficient and Reliable CompressorsApplies to All Models

Wat

er C

oole

d W

ater

Chi

ller

s

Wat

er C

oole

d W

ater

Chi

ller

s

ZUW175AY 1

1 compressoris operating

2 compressors

100

50

0 25 50 100

Power consum

ption ratio (%)

Cooling capacity ratio (%)

Increased characteristicunder partial load

Water Cooled Water Chillers

25 26

A s ingle built- in control box s implifies operation and control.

P rovides a s table supply of chilled water throughout the

Since the heat exchanger employs water, operation of the unit is not affected by changes in the outdoor temperature. A stable water temperature is maintained year round.

All controls and indicators are centralized in a single control box, making it possi-ble to control the system using fewer personnel. Installation is simplified by inte-gration of the control box with the main unit.

The water temperature setting can be set to any value between 4 and 25 .

The 10 HP model has a footprint measuring only 0.32 square meters .

8 to 30 HP models have a modular design that enables units with different capaci-ties to be used together in a single system and simplifies increasing system ca-pacity later on 3 — 5 HP models have a similar configuration and are designed for compactness.

The starter panel is built into the control panel, s implifying

Easy InstallationUWP 90AY 3 — 900AY 3

All models are fitted with a pressure gauge as s tandard.

P erformance characteris tics under partial load are efficient.

Reliability

Efficient Performance

Well Appointed

The new double-pipe heat exchanger design reduces clogging, significantly in-creasing resistance to dirty cooling water.

The double-pipe heat exchanger and an individual error indication function help reduce the manpower required for

MaintenanceUWP 90AY 3 — 900AY 3

UWD1320DY 1 — 4000DY 1

Year Round Cooling OperationApplies to All Models

Wide Water Temperature Control Range RangeUWP 90AY 3 — 900AY 3

Simple Operation and ControlUWD1320DY 1 — 4000DY 1

UWD1320DY 1UWP 900AY 3

Model LineupRefrigerant Units series Model No.

Capacity (kW) page

50/60Hz50Hz

R-407CR-134a

Standard UnitStandard Unit

UWP—AY3UWD—DY1

8/990—

13.2/15150—

20/22.4224—

26.5/30300—

40/45450—

53/60600—

67/75750—

80/90900—

118—

1320

150—

1700

180—

2000

236—

2650

300—

3350

355—

40002727

Refrigerant Units series Model No.

50Hz60Hz50Hz60Hz

R-134aStandard Unit

Brine Cooling Unit

ZUW—AY1ZUW—AYBZUW—AY1ZZUW—AYBZ

Capacity100RT

100—

100—

120RT120120120120

150RT150150150150

175RT175175175175

200RT200200200200

240RT240240240240

280RT280280280—

300RT300—

300300

350RT350—

350—

400RT400—

400—

28282929

page

: UWP S eries : UWD S eries ZUW S eries

E mploys the new refrigerants R -407C and R -134a.

New RefrigerantUWP 90 — 900AY 3UWD1320 — 40000DY 1 ZUW100 — 400AY (1) (B ) ZUW100 — 400AY (1) (B ) Z

To improve their operational reliability, 5 -- 30HP models employ scroll compressors , while 40 -- 120HP models are equipped with semi-hermetic s ingle screw compressors .

R efrigerant inlet

R efrigerant outlet

S emi-hermetic s ingle screw compressor

Efficient and Reliable CompressorsApplies to All Models

Wat

er C

oole

d W

ater

Chi

ller

s

Wat

er C

oole

d W

ater

Chi

ller

s

ZUW175AY 1

1 compressoris operating

2 compressors

100

50

0 25 50 100

Power consum

ption ratio (%)

Cooling capacity ratio (%)

Increased characteristicunder partial load

Water Cooled Water Chillers

25 26

S pecificationsUWP90AY3

(3 )UWP150AY3

(5 )UWP224AY3

(8 )UWP300AY3

(10 )UWP450AY3

(15 )UWP600AY3

(20 )UWP750AY3

(25 )UWP900AY3

(30 )Model

Cooling capacity(50/60 Hz)

Power supplyChilled water flow rate(50/60 Hz)Capacity steps

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)WeightOperating weight

TypeMotor output

Condenser water inlet/outletChilled water inlet/outletDrain outlet

kWBtu/hUSRT

/min

%

kW

mmkgkg

8.0/9.027,300/30,7002.28/2.563 phase, 50 Hz 380/400/415 V, 60 Hz 400/440 V, 3 wires system

23/26

100-0Hermetically sealed scroll type3.0 1Brazed plate heat exchangerDouble pipe condenserR-407CFPT1 (25A)FPT1 (25A)FPT3/4 (20A)1,280 405 690100102

13.2/15.045,100/51,2003.75/4.27

38/43

3.75 1

110112

20.0/22.468,300/76,5005.69/6.37

57/64

5.5 1

FPT1 1/2 (40A)FPT1 1/2 (40A)

1,280 405 790150154

26.5/30.090,500/102,0007.54/8.53

76/86

7.5 1

160165

40.0/45.0137,000/154,00011.4/12.8

115/129

100-50-0

5.5 2

FPT1 1/2 2 (40A)FPT1 1/2 2 (40A)

1,280 808 790305313

53.0/60.0181,000/205,00015.1/17.1

152/172

7.5 2

325335

67.0/75.0229,000/256,00019.1/21.3

192/215

100-60-0

7.5+5.5 2

FPT1 1/2 3 (40A)FPT1 1/2 3 (40A)

1,280 1,211 790465478

80.0/90.0273,000/307,00022.8/25.6

229/258

100-67-0

7.5 3

485500

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp. 30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Reverse-phase protector.

• Discharge gas overheat protector. • Fusible plug. • Safety valve.*3 This product is manufactured in Japan.

*1

8 / 9 — 80 / 90kW class

UWP 90 — 900AY 3Standard Unit

50/60Hz

S pecificationsUWD1320DY1

(40 )UWD1700DY1

(50 )UWD2000DY1

(60 )UWD2650DY1

(80 )UWD3350DY1

(100 )UWD4000DY1

(120 )Model

Cooling capacity

Power supply

Chilled water flow rate

Condenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min

/min

kW%

mmkgkg

118403,00033.63 phase, 50 Hz 380/400/415 V, 3 wires system

338

420

Semi-hermetic sealed single screw type30 1100-70-40-0Shell and Hi-X tube typeShell and cross fin tube typeR-134aFPT3 (80A)FPT3 (80A)FPT3/4FPT1/41,600 2,320 7591,1001,220

150512,00042.7

430

534

37 1

1,702 2,600 7591,2501,390

180615,00051.2

516

640

45 1

FPT4 (100A)4B Flange (JIS10K)(100A)FPT1

1,2801,420

236806,00067.1

677

837

30 2100-70-40-20-0

FPT3 (80A)

1,623 3,330 9941,8001,980

3001,020,00085.3

860

1,068

37 2

1,745 3,338 1,0502,2002,420

3551,210,000101

1,018

1,263

45 2

FPT4 (100A)5B Flange (JIS10K)(125A)

2,3002,520

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal

protector. • Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve(for UWD2000DY1,UWD4000DY1). *3 This product is manufactured in Japan.

*1

118 — 355kW class

UWD1320 — 4000DY 1Standard Unit

50Hz

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal

protector. • Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve. *3 This product is manufactured in China.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

367 — 1,450kW class

ZUW100 — 400AY 1Standard Unit

50Hz

ZUW100AY1(100RT)

ZUW120AY1(120RT)

ZUW150AY1(150RT)

ZUW175AY1(175 RT)

ZUW200AY1(200RT)

ZUW240AY1(240RT)

ZUW280AY1(280RT)

ZUW300AY1(300RT)

ZUW350AY1(350RT)

ZUW400AY1(400RT)

3671,252,1321043 phase, 50 HZ 380/400/415 V, 3 wires system1,0521,253 single screw compress37 2100 25-0 continuous capacity controlshell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) NPT1 1/2 1 NPT1 1/2 1 1,765 1,160 3,5303,500 3,700

4541,548,959129

1,3011,545

45 2

3,650 3,850

5081,733,196144

1,4561,727

3,750 4,000

6312,152,848179

1,8092,153

60 2

1,765 1,210 3,6803,900 4,150

7102,422,381202

2,0352,400

75 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,9604,750 5,050

8572,923,916244

2,4572,930

90 2

2,000 1,400 4,0005,250 5,600

1,0003,411,804284

2,8673,407

90+110

8B Flange (200A)

2,060 1,470 4,5506,650 7,100

1,1143,800,750317

3,1933,773

110 2

6,750 7,200

1,2604,298,874358

3,6124,235

130 2100 10-0 continuous capacity control

8B Flange (200A) NPT1 1/2 1, NPT1 1/4 2NPT1 1/2 1, NPT1 1/4 22,270 1,830 4,2508,300 8,900

1,4504,947,117412

4,1574,883

8,450 9,150

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal protector.

• Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

441 — 1,040kW class

ZUW120 — 300AY BStandard Unit

60Hz

ZUW120AYB(120RT)

ZUW150AYB(150RT)

ZUW175AYB(175RT)

ZUW200AYB(200RT)

ZUW240AYB(240RT)

ZUW300AYB(300RT)

4411,504,6061253 phase, 60 Hz 400/440 V, 3 wires system 1,2641,517single screw compress 37 2100 25-0 continuous capacity control shell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) FPT1/2 FPT1/2 1,765 1,160 3,4003,800 4,000

5421,849,198154

1,5531,864

45 2

4,150 4,400

6062,067,554172

1,7372,085

4,450 4,700

7592,589,560216

2,1752,609

60 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,6005,100 5,400

8482,893,211241

2,4302,903

75 2

2,000 1,400 3,9605,850 6,200

1,0403,548,277296

2,9813,584

90 2

8B Flange (200A)

2,060 1,680 4,0006,350 6,800

Water Cooled Water Chillers

Wat

er C

oole

d W

ater

Chi

ller

s

Wat

er C

oole

d W

ater

Chi

ller

s

27 28

S pecificationsUWP90AY3

(3 )UWP150AY3

(5 )UWP224AY3

(8 )UWP300AY3

(10 )UWP450AY3

(15 )UWP600AY3

(20 )UWP750AY3

(25 )UWP900AY3

(30 )Model

Cooling capacity(50/60 Hz)

Power supplyChilled water flow rate(50/60 Hz)Capacity steps

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)WeightOperating weight

TypeMotor output

Condenser water inlet/outletChilled water inlet/outletDrain outlet

kWBtu/hUSRT

/min

%

kW

mmkgkg

8.0/9.027,300/30,7002.28/2.563 phase, 50 Hz 380/400/415 V, 60 Hz 400/440 V, 3 wires system

23/26

100-0Hermetically sealed scroll type3.0 1Brazed plate heat exchangerDouble pipe condenserR-407CFPT1 (25A)FPT1 (25A)FPT3/4 (20A)1,280 405 690100102

13.2/15.045,100/51,2003.75/4.27

38/43

3.75 1

110112

20.0/22.468,300/76,5005.69/6.37

57/64

5.5 1

FPT1 1/2 (40A)FPT1 1/2 (40A)

1,280 405 790150154

26.5/30.090,500/102,0007.54/8.53

76/86

7.5 1

160165

40.0/45.0137,000/154,00011.4/12.8

115/129

100-50-0

5.5 2

FPT1 1/2 2 (40A)FPT1 1/2 2 (40A)

1,280 808 790305313

53.0/60.0181,000/205,00015.1/17.1

152/172

7.5 2

325335

67.0/75.0229,000/256,00019.1/21.3

192/215

100-60-0

7.5+5.5 2

FPT1 1/2 3 (40A)FPT1 1/2 3 (40A)

1,280 1,211 790465478

80.0/90.0273,000/307,00022.8/25.6

229/258

100-67-0

7.5 3

485500

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp. 30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Reverse-phase protector.

• Discharge gas overheat protector. • Fusible plug. • Safety valve.*3 This product is manufactured in Japan.

*1

8 / 9 — 80 / 90kW class

UWP 90 — 900AY 3Standard Unit

50/60Hz

S pecificationsUWD1320DY1

(40 )UWD1700DY1

(50 )UWD2000DY1

(60 )UWD2650DY1

(80 )UWD3350DY1

(100 )UWD4000DY1

(120 )Model

Cooling capacity

Power supply

Chilled water flow rate

Condenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min

/min

kW%

mmkgkg

118403,00033.63 phase, 50 Hz 380/400/415 V, 3 wires system

338

420

Semi-hermetic sealed single screw type30 1100-70-40-0Shell and Hi-X tube typeShell and cross fin tube typeR-134aFPT3 (80A)FPT3 (80A)FPT3/4FPT1/41,600 2,320 7591,1001,220

150512,00042.7

430

534

37 1

1,702 2,600 7591,2501,390

180615,00051.2

516

640

45 1

FPT4 (100A)4B Flange (JIS10K)(100A)FPT1

1,2801,420

236806,00067.1

677

837

30 2100-70-40-20-0

FPT3 (80A)

1,623 3,330 9941,8001,980

3001,020,00085.3

860

1,068

37 2

1,745 3,338 1,0502,2002,420

3551,210,000101

1,018

1,263

45 2

FPT4 (100A)5B Flange (JIS10K)(125A)

2,3002,520

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal

protector. • Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve(for UWD2000DY1,UWD4000DY1). *3 This product is manufactured in Japan.

*1

118 — 355kW class

UWD1320 — 4000DY 1Standard Unit

50Hz

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal

protector. • Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve. *3 This product is manufactured in China.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

367 — 1,450kW class

ZUW100 — 400AY 1Standard Unit

50Hz

ZUW100AY1(100RT)

ZUW120AY1(120RT)

ZUW150AY1(150RT)

ZUW175AY1(175 RT)

ZUW200AY1(200RT)

ZUW240AY1(240RT)

ZUW280AY1(280RT)

ZUW300AY1(300RT)

ZUW350AY1(350RT)

ZUW400AY1(400RT)

3671,252,1321043 phase, 50 HZ 380/400/415 V, 3 wires system1,0521,253 single screw compress37 2100 25-0 continuous capacity controlshell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) NPT1 1/2 1 NPT1 1/2 1 1,765 1,160 3,5303,500 3,700

4541,548,959129

1,3011,545

45 2

3,650 3,850

5081,733,196144

1,4561,727

3,750 4,000

6312,152,848179

1,8092,153

60 2

1,765 1,210 3,6803,900 4,150

7102,422,381202

2,0352,400

75 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,9604,750 5,050

8572,923,916244

2,4572,930

90 2

2,000 1,400 4,0005,250 5,600

1,0003,411,804284

2,8673,407

90+110

8B Flange (200A)

2,060 1,470 4,5506,650 7,100

1,1143,800,750317

3,1933,773

110 2

6,750 7,200

1,2604,298,874358

3,6124,235

130 2100 10-0 continuous capacity control

8B Flange (200A) NPT1 1/2 1, NPT1 1/4 2NPT1 1/2 1, NPT1 1/4 22,270 1,830 4,2508,300 8,900

1,4504,947,117412

4,1574,883

8,450 9,150

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.7 (44.5 F), entering chilled water temp.12 (53.6 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal protector.

• Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

441 — 1,040kW class

ZUW120 — 300AY BStandard Unit

60Hz

ZUW120AYB(120RT)

ZUW150AYB(150RT)

ZUW175AYB(175RT)

ZUW200AYB(200RT)

ZUW240AYB(240RT)

ZUW300AYB(300RT)

4411,504,6061253 phase, 60 Hz 400/440 V, 3 wires system 1,2641,517single screw compress 37 2100 25-0 continuous capacity control shell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) FPT1/2 FPT1/2 1,765 1,160 3,4003,800 4,000

5421,849,198154

1,5531,864

45 2

4,150 4,400

6062,067,554172

1,7372,085

4,450 4,700

7592,589,560216

2,1752,609

60 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,6005,100 5,400

8482,893,211241

2,4302,903

75 2

2,000 1,400 3,9605,850 6,200

1,0403,548,277296

2,9813,584

90 2

8B Flange (200A)

2,060 1,680 4,0006,350 6,800

Water Cooled Water Chillers

Wat

er C

oole

d W

ater

Chi

ller

s

Wat

er C

oole

d W

ater

Chi

ller

s

27 28

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal protector.

• Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

233 — 555kW class

ZUW120 — 300AY B ZBrine Cooling Unit

60Hz

ZUW120AYBZ(120RT)

ZUW150AYBZ(150RT)

ZUW175AYBZ(175RT)

ZUW200AYBZ(200RT)

ZUW240AYBZ(240RT)

ZUW300AYBZ(300RT)

233794,951663 phase, 60Hz 400/440 V, 3 wires system 1,242909single screw compress 37 2100 25-0 continuous capacity control shell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) FPT1/2 FPT1/2 1,765 1,160 3,4003,800 4,000

290989,42382

1,5461,118

45 2

4,150 4,400

3201,091,77891

1,7061,238

4,450 4,700

4001,364,722114

2,1321,542

60 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,6005,100 5,400

4601,569,430131

2,4521,783

75 2

2,000 1,400 3,9605,850 6,200

5551,893,552158

2,9582,159

90 2

8B Flange (200A)

2,060 1,680 4,0006,350 6,800

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal protector.

• Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

190 — 715kW class

ZUW100 — 400AY 1ZBrine Cooling Unit

50Hz

ZUW100AY1Z(100RT)

ZUW120AY1Z(120RT)

ZUW150AY1Z(150RT)

ZUW175AY1Z(175RT)

ZUW200AY1Z(200RT)

ZUW240AY1Z(240RT)

ZUW280AY1Z(280RT)

ZUW300AY1Z(300RT)

ZUW350AY1Z(350RT)

ZUW400AY1Z(400RT)

190648,243543 phase, 50Hz 380/400/415V, 3 wires system545730single screw compress37 2100 25-0 continuous capacity controlshell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) NPT1 1/2 1 NPT1 1/2 1 1,765 1,160 3,4003,500 3,700

243829,06969

697920

45 2

3,650 3,850

272928,01177

7801,032

3,750 4,000

3381,153,19096

9691,287

60 2

1,765 1,210 3,6803,9004,150

3821,303,309109

1,0951,458

75 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,9604,750 5,050

4591,566,018131

1,3161,758

90 2

2,000 1,400 4,0005,250 5,600

5341,821,904152

1,5312,049

90+110

8B Flange (200A)

2,060 1,470 4,5506,650 7,100

5992,043,671170

1,7172,282

110 2

6,750 7,200

6282,142,613179

1,8002,379

130 2 100 10-0 continuous capacity control

8B Flange (200A) NPT1 1/2 1, NPT1 1/4 NPT1 1/2 1, NPT1 1/42,270 1,830 4,2508,300 8,900

7152,439,440203

2,0502,723

8,450 9,150

ZUW200AY1ZUW175AY1ZUW150AY1ZUW120AY1ZUW100AY1Model

IPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timerUpgrader adaptor

DAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61GD3-ZUW100A

ZUW400AY1ZUW350AY1ZUW300AY1ZUW280AY1ZUW240AY1Model

IPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timerUpgrader adaptor

DAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61GD3-ZUW100A

Option L is t

Water Cooled Water Chillers

Wat

er C

oole

d W

ater

Chi

ller

s

Wat

er C

oole

d W

ater

Chi

ller

s

29 30

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal protector.

• Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

233 — 555kW class

ZUW120 — 300AY B ZBrine Cooling Unit

60Hz

ZUW120AYBZ(120RT)

ZUW150AYBZ(150RT)

ZUW175AYBZ(175RT)

ZUW200AYBZ(200RT)

ZUW240AYBZ(240RT)

ZUW300AYBZ(300RT)

233794,951663 phase, 60Hz 400/440 V, 3 wires system 1,242909single screw compress 37 2100 25-0 continuous capacity control shell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) FPT1/2 FPT1/2 1,765 1,160 3,4003,800 4,000

290989,42382

1,5461,118

45 2

4,150 4,400

3201,091,77891

1,7061,238

4,450 4,700

4001,364,722114

2,1321,542

60 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,6005,100 5,400

4601,569,430131

2,4521,783

75 2

2,000 1,400 3,9605,850 6,200

5551,893,552158

2,9582,159

90 2

8B Flange (200A)

2,060 1,680 4,0006,350 6,800

Notes:*1 Cooling capacity is based on the following conditions : Leaving chilled water temp.-5 (23.0 F), entering chilled water temp.-2 (28.4 F), leaving condenser water temp. 35 (95 F), entering

condenser water temp.30 (86 F).*2 The following safety devices are equipped as standard. • High/low pressure switch. • Freeze-up protection thermostat. • Overcurrent relay for compressors. • Compressor thermal protector.

• Reverse-phase protector. • Discharge gas overheat protector. • Fusible plug. • Safety valve.

S pecifications

Model

Cooling capacity

Power supplyChilled water flow rateCondenser water flow rate

Compressor

Evaporator typeCondenser typeRefrigerant

Pipeconnections

Dimensions (H W D)Weight (Approx.)Operating weight (Approx.)

TypeMotor outputCapacity control

Condenser water inlet/outletChilled water inlet/outletChilled water drain outletCondenser water drain outlet

kWBtu/hUSRT

/min /min

kW%

mmkgkg

190 — 715kW class

ZUW100 — 400AY 1ZBrine Cooling Unit

50Hz

ZUW100AY1Z(100RT)

ZUW120AY1Z(120RT)

ZUW150AY1Z(150RT)

ZUW175AY1Z(175RT)

ZUW200AY1Z(200RT)

ZUW240AY1Z(240RT)

ZUW280AY1Z(280RT)

ZUW300AY1Z(300RT)

ZUW350AY1Z(350RT)

ZUW400AY1Z(400RT)

190648,243543 phase, 50Hz 380/400/415V, 3 wires system545730single screw compress37 2100 25-0 continuous capacity controlshell and tube flooded type shell and tube type R-134a5B Flange (125A) 5B Flange (125A) NPT1 1/2 1 NPT1 1/2 1 1,765 1,160 3,4003,500 3,700

243829,06969

697920

45 2

3,650 3,850

272928,01177

7801,032

3,750 4,000

3381,153,19096

9691,287

60 2

1,765 1,210 3,6803,9004,150

3821,303,309109

1,0951,458

75 2

6B Flange (150A) 6B Flange (150A)

1,830 1,320 3,9604,750 5,050

4591,566,018131

1,3161,758

90 2

2,000 1,400 4,0005,250 5,600

5341,821,904152

1,5312,049

90+110

8B Flange (200A)

2,060 1,470 4,5506,650 7,100

5992,043,671170

1,7172,282

110 2

6,750 7,200

6282,142,613179

1,8002,379

130 2 100 10-0 continuous capacity control

8B Flange (200A) NPT1 1/2 1, NPT1 1/4 NPT1 1/2 1, NPT1 1/42,270 1,830 4,2508,300 8,900

7152,439,440203

2,0502,723

8,450 9,150

ZUW200AY1ZUW175AY1ZUW150AY1ZUW120AY1ZUW100AY1Model

IPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timerUpgrader adaptor

DAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61GD3-ZUW100A

ZUW400AY1ZUW350AY1ZUW300AY1ZUW280AY1ZUW240AY1Model

IPUDio unitD Air unitInterface for use in LONWORKS

Interface for use in BACnetCentral remote controllerUnified ON/OFF controllerSchedule timerUpgrader adaptor

DAM602A5DEC102ADAM101ADMS504B51DMS502A51DCS302CA61DCS301BA61DST301BA61GD3-ZUW100A

Option L is t

Water Cooled Water Chillers

Wat

er C

oole

d W

ater

Chi

ller

s

Wat

er C

oole

d W

ater

Chi

ller

s

29 30

Daikin Water Chillers are of the self-contained type. This means that they are assembled, internally wired and charged with refrigerant at the factory for easy installation, only requiring external wiring and plumbing on site. They are compatible with Daikin's Air Handling and/or Fan Coil Units.

All rights reservedPrinted in Japan 11/06/005 SW.HP.ADc

DealerHead Office:Umeda Center Bldg., 2-4-12, Nakazaki-Nishi,Kita-ku, Osaka, 530-8323 Japan

Tokyo Office:JR Shinagawa East Bldg., 2-18-1, Konan,Minato-ku, Tokyo, 108-0075 Japan

http://www.daikin.com/global/

1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided and choose an outdoor unit with anti-corrosion treatment.

Cautions on product corrosion

Warning Daikin Industries, Ltd.’s products are manufactured for export to numerous countries throughout the world. Daikin Industries, Ltd. does not have control over which products are exported to and used in a particular country. Prior to purchase, please therefore confirm with your local authorised importer, distributor and/or retailer whether this product conforms to the applicable standards, and is suitable for use, in the region where the product will be used. This statement does not purport to exclude, restrict or modify the application of any local legislation.Ask a qualified installer or contractor to install this product. Do not try to install the product yourself. Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion.Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or contractor to install those parts and accessories. Use of unauthorised parts and accessories or improper installation of parts and accessories can result in water or refrigerant leakage, electrical shock, fire or explosion.Read the User's Manual carefully before using this product. The User's Manual provides important safety instructions and warnings. Be sure to follow these instructions and warnings.

If you have any enquiries, please contact your local importer, distributor and/or retailer.

Printed on 100% recycled paper with soy ink.Specifications, designs and other content appearing in this brochure are current as of November 2006 but subject to change without notice.

ISO 14001 is the standard defined by the International Organization for Standardization (ISO) relating to environmental management systems. Our group has been acknowledged by an internationally accredited compliance organisation as having an appropriate programme of environmental protection procedures and activities to meet the requirements of ISO 14001.

About ISO 14001ISO 9001 is a plant certification system defined by the International Organization for Standardization (ISO) relating to quality assurance. ISO 9001 certification covers quality assurance aspects related to the “ design, development, manufacture, installation, and supplementary service” of products manufactured at the plant.

About ISO9001

JMI-0107 EC99J2044