Washer Specifications · ULP-302 ULP-402 Lath-Lock PBH™ Washer - 2” Diameter Also With Screws...
Transcript of Washer Specifications · ULP-302 ULP-402 Lath-Lock PBH™ Washer - 2” Diameter Also With Screws...
Washer Specifications
ULP-302
ULP-402
Lath-Lock
PBH™ Washer - 2” DiameterAlso With Screws for Wood/Lite Metal, Steel & Masonry
DP300™ Washer - 1 3/4” DiameterAlso With Screws for Wood/Lite Metal, Steel & Masonry
DP400™ Washer - 1 3/4” DiameterWith Pre-Spot Stem
DP500™ Tab Washer - 1 1/4” DiameterG-90 Chromium Plated Steel
Demand Products, Inc.
E q u i v a l e n c e s a n d A p p r o v a l s
• EIFS Manufacturers ApprovalsUpon Request
• 3rd Party Windload TestingUpon Request
• All Fasteners Meet or Exceed EIFSManufacturer Requirements —ASTM E330 and ASTM B117
8"
These spacing patterns aregeneral guidelines for mechan-ical installation of EPS to differ-ent substrates when used inconjunction with a typical EIFSsystem or similar systems.Construction projects vary andyours may be different fromthese fastener suggestions.Please consult your EIFS man-ufacturer when using Demandfasteners along with adhe-sives. For additional informa-tion call Demand ProductsTechnical Services at 1-800-325-7540
12" 12" 12"
6"
6"
6"6"
48"
24"
12"
Wood,Plywood,Metal Siding,Masonry andConcrete
24"
16" 16"
4"
4"
8"8"
48"
24"
8"
8"
6"
6 "
12"
8" 8" 8" 8" 8" StructuralSubstratesSuch asWoodSheathing,Concrete,Masonry &Metal Siding
Testing was performed by Underwriters Laboratories per ASTM E330 and E331. Procedure B
Non-StructuralSheathingssuch as OSB,Gypsum,Dens-GlassGold
48"
4"
24"
4"
4 "
8"
8"
4" 10" 10" 10" 10"
48"
StructuralSubstratesSuch asWoodSheathing,Concrete,Masonry &Metal Siding
Screw Pullout Performance Data
Fastener Depth of Embedment in Solid Material (inches)Diameter 1" 11⁄4" 11⁄2" 13⁄4"
3⁄16" 341 581 863 1059Test #CH3932/Pittsburgh Testing Laboratories
Fastener Depth of Embedment in Solid Material (inches)Diameter 1" 11⁄4" 11⁄2" 13⁄4"
3⁄16" *209 *357 *468 *547Test #CH3748/Pittsburgh Testing Laboratories
Nominal Gauge 26 24 22 20
Pullout Strength 120 183 248 296
Nominal Gauge 18 16 14 12
Pullout Strength 471 679 847 1225
MASONRY
STEEL
Coating: CLIMACOAT™Corrosion Resistance: Kestemich Results (Din 50018, 2.OL ) • 20 cycles - 10% or less red rust. SaltSpray Results (ASTM B117) • 500 hours - 10% or less red rust for wood,lite-metal and steel fasteners.
Solid Concrete
Hollow Block
Coating: CLIMASEAL™ for masonry/concrete fasteners onlyCorrosion Resistance: Kestemich Results (Din50018, 2.OL) • 30 cycles - 10% or less red rust.Salt Spray Results (ASTM B117) • 720 Hours -10% or less red rust.
Coating: CLIMASEAL™ for masonry/concretefasteners onlyCorrosion Resistance: Kestemich Results (Din50018, 2.OL) • 30 cycles - 10% or less red rust.Salt Spray Results (ASTM B117) • 720 Hours -10% or less red rust.
*Note 1: Masonry must be pre-drilled 1⁄2" deeper than fastener penetration.*Note 2: Hardness of masonry varies and the standard drill bit may not always drill
the adequate hole. Please consult Demand Products for assistance in prop-er drill bit diameter.
(1⁄4" Minimum Through Penetration) (1⁄4" Minimum Through Penetration)
Please Note: The pullout values listed are the ultimate averages achieved under laboratory conditions.An appropriate safety margin factor should beapplied to these values to achieve adesign value.
CONCRETE
(conforms to ASTM C-548 & C-1002) (conforms to ASTM C-954 & C-548)
W00D
METAL
LT.
A
B
C
D
Windload Specs for PB & PBH Washers
Wind-Devil® 2
All of Our Screws Meet or Exceed ASTM B117
Non-Approved Fasteners & Uncoated Screws Can Cost
You, Your Reputation
1.0 Lb. EPS Pattern A Pattern B1" 83 85
11/2" 105 104
Wind Load Capacity(Average Ultimate PSF, Negative Pressure
2” Diameter •
•
• •
•Large Keyholes forStrong Mechanical Bond
Popouts
Finger Closures
Exceeds Miami/Dade Wind-Load Pull-Off Minimum of 90 PSF
Eliminates Thermal Bridging
White — No Color Bleedthru
For Polymer Based EIFS
Designed for ALLEPS Thicknesses
For PolymerBased Systems
EIFS MANUFACTURER APPROVED
PBH PB
Available Pre-Assembled for Wood/Lite Metal, Steel & Masonry
Demand Products Assembled Fasteners
3. Install PBH™ or PB™ in a manner so the fasteneris flush with the surface of the InsulationBoard. Do not exceed 1.6 mm (1/16”) belowthe surface.
4. Rasp the surface of the Insulation Boardwith a DuraVac™ DuraRasp™ to remove any irregularities.
1. Insulation Board shall be attached to theapproved substrate horizontally with vertical joints staggered and butted tightly.
2. PBH™ or PB™ by Demand Products, Inc. aredesigned to be used with EIFS ManufacturersPB EIFS. Screws shall meet ASTM B117.
Cone DesignPrevents Popouts
CREATING SOLUTIONS FOR THE FOAM INDUSTRY
1055 Nine North Dr. | Alpharetta, GA 30004 USA TEL. 770.772.7448 | FAX. 1.770.772.4618 | TEL. 800.325.7540
www.demandproducts.com | [email protected]